Search Documents

By C Rothfuss, X Wang, S J. Herbert, K Prasad

The extraction of groundwater to produce gas from coal seam gas (CSG) reservoirs has highlighted the opportunity for beneficial uses of groundwater in Australia. This paper presents an assessment of alternate groundwater modelling approaches that can be used for assessment of one beneficial use option, that of injection. This assessment examines the outcome of the use of different simulation methods on predictions of hydrodynamic behaviour.In this paper, a simplified hydraulic concept of a multi-aquifer system within the hypothetical injection field was used to investigate the hydrodynamic behaviour of injection into the Precipice Sandstone. Comparisons were made through the analysis of a Theis 3D analytical solution with 2D and 3D numerical solutions. The paper discusses the different solution methods and the impact of these on predictions of pressure and flux. Differences in 2D and 3D solutions result in implications if planning injection as a beneficial use of water. For example, the 2D solution resulted in faster and higher injection pressure build-up when compared to the 3D solutions. The 2D modelling could result in either plans that require higher capital expenditure for a greater number of wells in order to spread the pressure effect and remain below the maximum injection pressure or a reduced injection rate. Meanwhile, the 3D modelling with sensitivity analysis could result in planning for lower capital expenditure for fewer wells required to spread the pressure effect and remain below the maximum injection pressure. CITATION:Wang, X, Herbert, S J,?Rothfuss, C and Prasad, K, 2013. Assessment of effectiveness of artificial recharge for coal seam gas water management based on numerical modelling, in Proceedings Water in Mining 2013 , pp 67-72 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By I Zh Bunin, V A. Chanturia, V G. Minenko, M V. Ryazantseva, A L. Samusev

A promising source for the extraction of rare metals and REEs in Russia is the eudialyte ores of the Lovozero deposit, which do not contain active uranium components. The eudialyte ore reserves of the Lovozero Massif are considered virtually unlimited and therefore have the potential to become a primary source of a number of rare and rare earth metals. The goal of this study was to comprehensively examine the effect of the parameters of high-power nanosecond electromagnetic pulses (HPEMP) and dielectric barrier discharge (DBD) on the leaching performance of eudialyte concentrate and the selective separation of zirconium and REEs from productive solutions. Using scanning electron microscopy and infrared spectroscopy, the mechanism behind the intensification of acidic dissolution of eudialyte as a result of pretreatment with energy impacts was described. During the HPEMP treatment, weakening and destruction of the eudialyte surface was observed, which at the substructural level is expressed in the deformation and local destruction of Si10O27, Si9MO30 resulting in formation of microcracks. During the DBD treatment, the formation of characteristic defects was observed in the form of imprints of dielectric breakdown microchannels and individual mineral fragments. Pretreatment of eudialyte concentrate using HPEMP made it possible to increase the recovery of zirconium into the pregnant solution of leaching by 3.4–4.3 per cent (from 86.6 per cent to 90.9 per cent) and by 4.1 per cent (from 86.6 per cent to 90.6 per cent) when using DBD. The increase in the total recovery of REEs was 1.2–1.8 per cent (from 87.7 per cent to 89.2 per cent). The effect of pH values, solution temperature, initial concentrations of valuable components on the successive recovery performance of zirconium and REEs from the pregnant solutions nitric from the acid leaching of eudialyte concentrate by chemical precipitation was examined. The possibility of selective separation of the zirconium product and rare earth elements with a zirconium recovery of 99.95 per cent and a REE recovery of 87.5 per cent was established. REE loss with the zirconium product was 8.0 per cent and 4.5 per cent with the spent pregnant solution.

Aug 24, 2022

The series of events leading to the adoption of more complex flotation circuits for coal have been reviewed. In essence, it has been concluded that ac- ceptable overall flotation recovery will only be obtained when efficient distri- bution of collector over all the component feed size fractions is ensured. The achievement of this goal is most likely to be obtained by feed classification and separate flotation of appropriate size fractions. The adoption of such a phil- osophy, however, imposes a number of process problems of both a chemical and an engineering nature. Some of these problems have been identified and possible solutions discussed. A case is emerging for the development of a new generation of flotation cells designed specifically for the flotation of classified coal and for the development of a series of novel re- agents which have the propensity to float middling particles.

Jan 1, 1984

Technological advances evolve in different ways; many are the result of years of application of scientific method. i.e. Observation Deduction Hypothesis Proof In the mining industry, better explosives, drill bits or reagents are likely to evolve in this way. The scientific method is suited to the application of conventional management structures. Other advances are simply the result of a "brainstorm", or building a better mousetrap. Such inspiration probably resulted in "Split Set" rock bolts, or the first use of a vacuum cleaner principle for shaft mucking. Individual consultants can apply lateral thinking to generate such inspiration. In gathering material for the presentation of this paper, I sent a.letter to all members of the Mineral Industry Consultants Association asking them to nominate problems in the industry requiring investigation. The answers have been divided into two classifications - contract research underway and identified problems requiring solutions.

Jan 1, 1986

By Jones JJ

A laboratory study of size segregation is described using a model of a Paul Wurth hopper industrailly employed for blast furnace charg- ing purposes. Experimental charge materials used in the study were glass ballotin.i (1-4mm dia.) and sinter fines (0.25-4mm). The tracer material employed consisted of coloured glass beads. The results of the study show that the discharge stream from a Paul Wurth hopper is characterised by an initial negative segregation followed by a positive segregation and that this segregation pattern is a property of the hopper geometry and the filling conditions. A simple computer model based on experimental tracer concentration results is proposed. The measured segregation results and those predicted by the model show close agreement. Application of the results with special reference to the effect of size segregation on charge permeability in blast furnaces is also included.

Jan 1, 1984

As economic, technological, regulatory and other forces continue to present the global mining industry with new opportunities and challenges, agile mining equipment manufacturers are stepping up their efforts to anticipate and meet the evolving needs of surface and underground mining operations. Operational excellence û the pursuit of efficient, lowest-possible-cost production û is a prime objective for all mines. As mineral commodity markets experience cyclical price highs and lows, mine operators, increasingly, look to their equipment suppliers for equipment and support that can help reduce multiple tangible and intangible operating costs. This paper explores how two mining equipment manufacturers û P&H Mining Equipment, a supplier of surface mining equipment and Joy Mining Machinery, a supplier of machinery for underground mining û are responding to the mining industryÆs aggressive pursuit of obtaining reduced operating cost with innovative products and support programs.

Jan 1, 2000

By Hale C. T, Carnie W. A

Rosebery mine has had over 100 years of mining activity. The reserve has remained static for the last eight years with an expected mine life of six years. A move to rectify this was made in 1994 with the birth of the Deep Exploration Project (DEP). $45 M was committed to drill 100 km of underground exploration diamond drilling and develop 5.5 kin of decline aiming to add 9.5 Mt to the reserves and minimise lead time for development of P and K lenses discovered in the early-1990s. In 1996 this aim was expanded with the objective to build the resource base to 20 Mt by June 2000 allowing the mill to operate at 1.0 Mtpa (0.9 Mt from underground). Preliminary results of the project to-date are outlined and exploration diamond drilling techniques and strategies are described.

Jan 1, 1997

Technological advances evolve in different ways; many are the result of years of application of scientific method. i.e. Observation Deduction Hypothesis Proof In the mining industry, better explosives, drill bits or reagents are likely to evolve in this way. The scientific method is suited to the application of conventional management structures. Other advances are simply the result of a "brainstorm", or building a better mousetrap. Such inspiration probably resulted in "Split Set" rock bolts, or the first use of a vacuum cleaner principle for shaft mucking. Individual consultants can apply lateral thinking to generate such inspiration. In gathering material for the presentation of this paper, I sent a.letter to all members of the Mineral Industry Consultants Association asking them to nominate problems in the industry requiring investigation. The answers have been divided into two classifications - contract research underway and identified problems requiring solutions.

Jan 1, 1986

By M Barley, C A. RosiFre, L Lobato

The Carajßs iron ore deposits contain approximately 17.5 billion tons of ore with >64 per cent Fe and occur in the eastern part of the Amazonas Craton. They are hosted by jaspilitic banded iron-formation (BIF) of the Carajßs Formation which, together with metavolcanic rocks, comprise the ~2.75Ga Grpo Parß Group of the Itacai·nas Supergroup in the ~1000 km long, E-W trending Carajßs Synclinorium. The Carajas Formation comprises discontinuous layers and lenses of partly dolomitised BIF (17 - 43 per cent Fe and 35 - 61 per cent SiO2) and lenses of high-grade iron ore, cut by mafic sills and dykes. The high-grade iron ores occur as large tabular bodies of friable (soft) hematite with smaller lenses of hard (compact) hematite. The hard hematite ores typically occur at the contact with the underlying volcanic rocks and are surrounded by an aureole of hydrothermal carbonate alteration. BIF that has been overprinted by dolomite and magnetite crystallisation has recently been discovered at depth in the N4E Mine. With increasing amounts of carbonate, the original lamination (microbanding) and other fine primary structures in the BIF have been progressively obliterated resulting in alternating carbonate and iron oxide mesobands. The friable hematite ore that is characteristic of the Carajßs deposits results from ongoing weathering and leaching of the carbonates from this type of altered BIF. The hard hematite ores probably result from more extensive early oxidation. The association of both carbonate-altered and jaspilitic BIF with the N4 Mine is similar to that observed at the Mount Tom Price deposit in Western Australia, where carbonate-altered BIF occurs below massive hematite ore with a jaspilitic halo developed above the orebody. This indicates that as at Mount Tom Price, hydrothermal carbonate alteration and associated loss of silica from BIF may be an important step in the formation of these giant hematite deposits.

Jan 1, 2002

By J Leppinen, B Johanson, R Kalapudas, G McMahon

The Suurikuusikko gold deposit was discovered in 1987 in western Finnish Lapland, 54 km NNE from the town centre of KittilS in the volcanic belt of Central Lapland. It is hosted by tholeiitic basalts in a graphite-bearing albitite breccia. The ore is located in subvertical shear zones characterised by strong albitisation, carbonatisation and sulfidisation. The ore minerals consist of arsenopyrite, pyrite, chalcopyrite, sphalerite, tetrahedrite, bournonite and rutile. Small amounts of pyrrhotite, gersdorffite, jamesonite, bornite, gudmundite, tetrahedrite, stibnite, kermesite, berthierite and native Sb are also present. Gold occurs as invisible and as 1 - 2 ¦m size inclusions in arsenopyrite and pyrite, on their grain boundaries and in fractures. The average amount of gold leached by cyanide is 2.93 per cent. The æinvisibleÆ gold contents were studied in pyrite and arsenopyrite by electron microprobe analysis (EPMA) and secondary ion mass spectrometry (SIMS) at CANMET/ MTL. Gold element distribution images show zoned patterns both in pyrite and arsenopyrite. SIMS analyses range from 343 to 55 ppm Au in arsenopyrite and from 217 ppm down to 0.32 ppm (detection limit 478 ppb) Au in pyrite. EPMA results range from 939 to below the detection limit 24 ppm Au in arsenopyrite and from 267 ppm to below 22 ppm Au in pyrite. Recovery of the refractory gold ore was studied using grinding, flotation, bio-oxidation and cyanidation tests. A sulfide bulk concentrate containing 40 ppm Au was obtained by flotation at 90 per cent recovery (As content 5.5 per cent, S content 22 per cent, and mass recovery 15 per cent). The grinding fineness in flotation was P80 -100 to 120 ¦m. At the original fineness the cyanidation recovery from the concentrate was lower than ten per cent, after ultra-fine grinding P80 -10 to 2 ¦m the Au recovery was less than 17 per cent. After bio- oxidation, Au recovery of 95 per cent was obtained in carbon-in-leach (CIL). The bio-oxidation time was two weeks in laboratory test, but after regrinding the oxidation rate was faster and recovery of Au higher. However, the selected method for the mining to be started in summer 2008 is open pit mining and mineral processing methods sulfide flotation and pressure oxidation in an autoclave. The ore reserves were estimated 31 December 2007 as: Probable 18.2 Mt with 5.1 g/t Au, Indicated 5.4 Mt with 3.0 g/t Au and Inferred 10.8 Mt with 3.4 g/t Au. The production capacity will be 3000 t/day.

Jan 1, 2008

By Reichardt Y

Fine feed fractions in the size range from 1 to 40 ¦m of materials with different hardness as limestone and silicon carbide have been stressed in two different devices. A tungsten-carbide-blodc allows a single stressing with a pressure up to 2000 MPa and a 4-piston-block enables a multiple stressing procedure in which the material bed is stressed in alternating directions with a pressure up to 700 MPa. The experiments show energy absorption as the major factor for the interparticle breakage of hard material, like quartz, zircon silicate, silicon carbide and smelted oonindum, pressure, however, does not influence the results within the investigated range from 100 to 700 MPa and even up to 2000 MPa for corundum. But the breakage of the middle-hard limestone depends on the pressure so far as more fineness can be produced if the same energy is introduced at a lower pressure level. The creation of very fine and microfine fragments decreases strongly with increasing hardness of the feed materiaL The energy consumption for producing microfine material with a multiple stressing procedure on a particle bed is much lower than that one of a usual milling process. But this procedure needs a classification with a seperation cut at a couple of microns, which is not easy to accomplish.

Jan 1, 1993

By N J. Beukes, S T. Netshio, M O. de Kock

The Thabazimbi iron ore deposit comprises a series of stratabound orebodies, on average 18 - 25 m thick that are aligned along the faulted basal contact between the Penge Iron Formation and dolostones of the Malmani Subgroup, Transvaal Supergroup. Field geological relationships and petrographic observations suggest that the formation of high-grade iron ores took place after contact metamorphism related to the intrusion of the Bushveld Complex (2.06 Ga) but before the deposition of red beds of the Waterberg Group at ca 1.9 Ga. Hard, high-grade iron ores are predominantly composed of martite and microplaty hematite. Goethite is restricted to supergene-modified ores close to the Late Cretaceous û Early Cenozoic Old African land surface. At depth, the high-grade hematite ores interfinger with low-grade dolomite-hematite and calcite-hematite ores. Iron oxides (martite, microplaty hematite) present in these low-grade ores are texturally indistinguishable from those in the associated high-grade ores, ie ore formation is genetically associated with carbonate metasomatism. Microthermometric studies of fluid inclusions in sparitic carbonates and rare megaquartz reveal their hydrothermal origin. Two compositionally distinct aqueous fluids of shallow crustal origin are identified, namely a Ca-Na-rich high-salinity brine (26 wt per cent NaClequivalent, TH ~160¦C), and an aqueous Mg-K-bearing fluid of intermediate salinity (8.3 - 12.6 wt per cent NaClequivalent, TH~120 - 150¦C). The results confirm that high-grade hematite orebodies at the Thabazimbi deposit owe their origin to an event of extensive oxidative carbonate metasomatism (calcification), similar to that recognised at other important high-grade iron ore deposits in the world. Hydrothermal ore formation is both structurally and lithologically controlled. Size and quality of the orebodies was improved by Late Mesozoic-Cenozoic deep lateritic weathering as carbonate-hematite ores were enriched to friable high-grade ores, but this supergene modification is second in importance compared to the primary event of hydrothermal ore formation.

Jan 1, 2005

By Scoble M, Peck J

This paper reviews the instrumentation and monitoring of blasthole drills and electric mining shovels at a surface coal mine in western Canada. The drill monitoring component involved the development and implementation of microprocessor-based hardware on Bucyrus-Erie 45R and 60R drills. Over a two year period 3800 metres of blasthole drilling were monitored The drill data was subsequently correlated with core and geophysical logs towards identifying unique and reproducible ranges of performance parameter data for the different rock types penetrated. Using this technique, the geology of the study area benches was characterized in detail. Once these same benches had been blasted, the performance of a P&H 2800XP shovel was monitored as it worked through the blasted ground. In this regard, the influence of different digging conditions on shovel performance were identified in a range of blast and geological environments within the study area. The precise nature of these environments was confirmed by a correlation with the interpreted drill monitored data and muckpile size distributions obtained from a digital photo-analysis study. The excavation of 500 000 bcm of waste was thus monitored and a digging index derived which reflected variations in muckpile diggability. The paper concludes by proposing an integrated monitoring approach which, as a first step, uses interpreted drill data for explosive loading. This capability would permit greater accuracy in explosives loading ie. charge placement within higher strength lithologies, while avoiding weaker units. The performance of an instrumented shovel would then be monitored as it works through the resulting muckpile. Interpretation of the shovel performance data would determine the overall quality of the blast in terms of a digging index (DI), providing an indication of the relative digging effort and the effectiveness of the blast design.

Jan 1, 1990

The Ravensworth-Liddell area is part of the Muswellbrook- Singleton Coal District of the Northern Coalfield. It lies in the Parishes of Liddell, Ravensworth, Vane and Howick, in the County of Durham, midway between Singleton and Muswellbrook, and is traversed by the Great Northern Railway, and the New England Highway.Ravensworth and Liddell railway stations are 57 miles arid 61 miles, respectively, north from Newcastle (Fig. 1).The area has been the centre of an intensive search for open cut coal during the past few years. More than 1,200 bores, of which about 10% were cored diamond drill holes, were drilled to depths of about 200ft. Portions with thicker cover have been explored by 10 diamond drill holes to depths of over 400ft. but core recovery from these deeper holes was poor, and the lack of detail in the recorded logs limits geological interpretation. The drilling has proved about 34,000,000 tons of open cut coal, and about 246,000,000 tons under deeper cover.GEOLOGYThe Ravensworth-Liddell area lies on the eastern flank and southern extremity of the Muswellbrook Dome, extending from Hebden in the north, to Jerry's Plains in the south, and the rocks under consideration belong to the Tomago Stage of the Upper Coal Measures. On the north they are truncated by the Hebden Thrust fault, which has a throw of about 4,500ft. (Raggatt, 1929). On the west they are bounded by outcrops of the Upper Marine Series, which conformably underlies the Upper Coal Measures, and...

Jan 1, 1953

By X Ma

Kaolinite is of very fine particle size in nature and thus its dispersion plays a key role in the successful removal of kaolinite in iron ore flotation and selective flocculation processes. As the most widely used dispersant in the world, sodium silicate has been used as a standard dispersant for kaolinite in the iron ore industry. However, the actual effect of sodium silicate on the colloid stability of kaolinite particles and its dispersion mechanism remain unknown in the literature. In this work, the dispersion effect and dispersion mechanisms of some common inorganic and organic dispersants, including sodium silicate, polyphosphate and a low molecular weight polyacrylic acid, on kaolinite particles were systematically investigated through electrophoretic mobility and colloidal stability studies over a wide pH range. It was found that sodium silicate-kaolinite interactions only take place in the neutral and acidic pH range, while polyacrylic acid and polyphosphate interact with kaolinite from pH 3 to 10.5. Consequently, sodium silicate only disperses kaolinite at neutral and acidic pH. In contrast, polyacrylic acid and polyphosphate disperse kaolinite from pH 3 to 10.5, with strong dispersion effect observed at neutral and acidic pH. In the iron ore industry, selective fl occulation and reverse cationic fl otation, the most widely used flotation route, are both conducted at pH 10 to 10.5. The results of the present study show that, at such high pH, polyacrylic acid and polyphosphate are more effective dispersants of kaolinite, in comparison with sodium silicate.

Jul 11, 2011

By Lawless JV

Recent exploration for gold on the Pacific Rim has utilised similarities between active hydrothermal systems and epithermal gold deposits. The major control over formation of such deposits is the hydrology of the ore-depositing hydrothermal system, which varies depending upon its geologic setting.

Jan 1, 1987

By Hommert P. J, Brown B

Early attempts at estimation of stress wave damage in blasting by use of finite element analysis met with limited success due to numerical instabilities that prevented calculations from being carried to late times. An improved damage model based on microcrack growth in tension allows finite element calculations which remain stable at late times. Estimation of crater profiles for blasting experiments in granite demonstrate successful simulations with this model.

Jan 1, 1990

By Sharmil Markar M

Ballarat Goldfields Limited is currently re-opening the old workings of the East Ballarat Goldfield which contain an estimated 1800 ML of groundwater. The disposal of this 'minewater' was of concern: the minewater is of moderate salinity; increased salinity levels have interfered with agriculture and water use at a number of locations downstream from Ballarat. Extensive numerical studies indicated that treated minewater could be discharged into the Ballarat Creek system for dilution by sewage effluent and by surface runoff after rainfall events. An automatic real-time salinity management system has been developed to enable the disposal of saline minewater in this fashion. A desk top computer operates the system: discharge and salinity readings are taken automatically each hour and filed away; the maximum allowable rate of discharge of treated minewater is calculated; pumps are switched on and off. The system readily enables daily, weekly and monthly data reports together with floppy disks of 'raw' data to be prepared in formats suitable for direct submission to the Victorian Environmental Protection Authority.

Jan 1, 1990

By G Chen

Magnesite and dolomite are two salt-type minerals. The surface characteristics of these two minerals are almost the same. It is very difficult to remove dolomite from magnesite ores by flotation process. The present study was performed to develop a new collector and a better flotation scheme for magnesite from dolomite. The flotation tests show that there exists a significant difference in flotability between magnesite and dolomite when dodecyl phosphate synthesised with dodecanol, phosphorus oxychloride and other chemicals is used as collector. Sodium silicate was used as the modifier to improve flotation selectivity. It was found that sodium silicate selectively depressed magnesite at pH 4.5 - 7.5. The separation of magnesite from dolomite was achieved in a reverse flotation which resulted in a 76.1 per cent yield of magnesite with a grade of 47.3 per cent at 100 ppm dodecyl phosphate and 75 ppm sodium silicate. The flotation mechanism was investigated by characterising surface electrical properties and measuring the adsorption density of the reagents on magnesite and dolomite.

Jan 1, 2005

By Pollard DM, Willis GM

The removal of bismuth from liquid copper in a vacuum furnace was studied over a range of pressures. The rate determining step changes from diffusion in the gas at pressures above 0.2 Torr to approach the Langmuir evaporation rate at pressures of 10-2 Torr. Oxygen and sulphur were found to have a negligible effect on the rate. Bismuth removal from copper sulphide was found to be considerably slower than from copper. This is consistent with the known thermodynamic properties of ternary sulphide melts.

Jan 1, 1980