Search Documents

By J Pan, Q H. Li, D Q. Zhu, C C. Yang, X Wang, Z Q. Guo

Al2O3 in natural iron ores generally occurs in goethite, kaolinite, gibbsite, hematite and iron carbonate. When the content of alumina in sinter increases from 1.11 per cent to 3.50 per cent, the reducibility of sinter decreases with the addition of four different types of alumina. When gibbsite and kaolinite are added, the low temperature reduction disintegration (RDI+3.15 mm) of sinter increases with the increase of Al2O3 content in the range of 1.5 per cent to 3.5 per cent. Furthermore, when adding pure reagent alumina, the increase of Al2O3 content in the range of 1.5 per cent to 3.0 per cent will increase the RDI+3.15 mm of sinter. The addition of ferric oxide–alumina spinel with the Al2O3 content in the range of 1.5 per cent to 2.5 per cent, also increases the RDI+ 3.15 mm of sinter. The influence difference is results from the change of the mineral composition and microstructure of sinter because of the occurrence state of Al2O3. Under the condition that Al2O3 content of sinter is 2 per cent, the porosity of sinter with kaolinite is 37.26 per cent, and the shape is irregular. When gibbsite and ferric oxide–alumina spinel are added, the porosity of sinter is about 16 per cent, and the pores are round. When pure reagent alumina is added, the porosity of sinter is 17.49 per cent, and the pores are regular and small. When kaolinite, gibbsite and ferric oxide–alumina spinel are added, platy calcium ferrite is mainly formed in the sinter, and some of it is columnar calcium ferrite. On the other hand, when pure reagent alumina is added, in addition to platy columnar calcium ferrite, acicular calcium ferrite is also formed in the sinter.

Nov 8, 2021

By E Philippa, J Vitanza, C Hawtin, B Miller

B Miller , E Philippa , C Hawtin and J Vitanza

Mar 22, 2022

By R Ibarra, H Solis, G Teowee, B E. Papillon

The authors have previously described a piezoelectric-based system to measure the dynamic pressure during actual detonation in the field. This technique is used in a water hammer test set-up where a donor detonator is fired first, with the pressure sensor and an acceptor electronic detonator placed underwater in a water tank, and maintained at a fixed distance away from the donor detonator. The functioning and timing of the acceptor detonator are captured using a customised microcontroller board called the water hammer timer. Using such water hammer testing, the effect of dynamic pressure was studied as a function of the magnitude of pressure during the electronic timing countdown. Data obtained indicate there is no significant impact in the timing of the electronic detonators in contrast to what has been reported in non-electric detonators.CITATION:Teowee, G, Solis, H, Papillon, B E and Ibarra, R, 2015. Effect of dynamic pressure on electronic detonator timing, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 575–578 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

Morning Star Gold aims to enter the ranks of Australia's gold producers, revitalising the Eastern Victorian Goldfi elds in the second half of 2010 - the fi rst gold production in around 50 years from the Morning Star Gold mine, which was once Australia's largest under WMC. This presentation will outline the redevelopment of the Morning Star Gold Mine from exploration to production. Morning Star Gold NL's (MCO) key project area is centred at the historic mining town of Woods Point and nearby Matlock (to the southeast) and Gaffney's Creek (to the northwest), all of which are located in the lower part of the Victorian Alps roughly 60 kms south of Mansfield. Morning Star has literally numerous historic mines and gold bearing 'dykes' on its tenements, many with a rich production history of high-grade gold from quartz reefs and alluvial sources. The area encompassing the Woods Point goldfi eld and the multiple high-grade gold bearing dyke structures located north towards Jamieson and south towards Walhalla formed one of the most significant mining fields in Australian history. Historical gold production was at least 155 t or around six million ounces of over a century of mining with an average production grade exceeding 27 g per tonne. The bulk of this recorded production came from just a handful of mines and of those only three were mined to any great depth. One of the key historical production hubs in this area was the famous 'Morning Star' mine, which is situated adjacent to Woods Point township. The Morning Star mine produced almost one million ounces at 27 grams per tonne, operating fairly continuously between 1861 and 1959 with a break after Jan 1939 due to the devastating 'Black Friday' bush fi res across eastern Victoria. During the early 1940s, the Morning Star was Australia's biggest gold mine. The Morning Star mine along with Walhalla ensured that this goldfield was third behind Bendigo and Ballarat as Victoria's biggest hardrock gold production centre. Morning Star Gold has rebuilt its 100 per cent owned 'Morning Star' mine with a view to producing gold in the second half of 2010. Morning Star is exploring its regional dykes in order to estimate an overall gold endowment and rank local production sources to feed its proposed mill at the Morning Star mine site. Key initial targets (all within 11 kms of the Morning Star mine) are the Waverly, All Nations, Rose of Denmark, Hunts, Wallaby and Loch Fyne dykes, all of which historically produced high grade gold, much of it gained from only shallow workings above the water table in the weathered zone of rocks. Historically the Morning Star mine was developed over 24 levels to a depth of 940 m via one large vertical shaft and a smaller, deeper inclined shaft at the 1900 feet level underground. At present MCO has dewatered and completely refurbished all infrastructure to the ten level (~310 m below surface). MCO knows there are a number of substantially under-explored and undeveloped or partially developed but not stoped areas within the Morning Star mine. As a result, MCO has been carrying out extensive channel sampling and an underground diamond drilling program targeting areas of the mine that were largely unexplored and undeveloped by the last operators of the mine - Western Mining Corp Ltd (Gold Mines of Australia). Four thousand, fi ve hundred pages of archival WMC records have helped the cause significantly. The shaft refurbishment and reconstruction stage is complete. This has been a program that originally commenced back in 1993 and has cost around $22 M. This refurbishment paved the way for the extensive underground resource focused diamond drilling program, which MCO completed in 2008 with two company-owned and operated drill rigs from drill cuddies on level 9 (900 feet underground) of the mine. This drilling, which encountered some stunning grades intersections and multiple visible gold hits, has outlined further production opportunities including 0.4 m @ 1392 g/t Au (MS 410). Metallurgical testing conducted by Gekko Systems of samples obtained from the exploration program found gravity concentration and a leach circuit gave recoveries of ~95 per cent to 99 per cent, or ~92 per cent from gravity alone at a coarse crush (300 ¦m). Currently, the plan is to use gravity to fi rstly produce dore bars on-site from the free milling gold and secondly a saleable concentrate for CIL processing off-site. A purpose built 10 t/h (~80 000 t/a) gravity treatment plant was subsequently ordered from Gekko and is expected to be installed onsite and commissioned in the Q3 2010. The plant features fi ne crushing with a vertical shaft impactor, followed by gold concentration by inline pressure jig, inline spinner and Wilfley table. This is an ABSTRACT ONLY. No paper was prepared for this presentation.

Aug 1, 2010

By D Semini, B Newcombe

Base-metal sulfide refractory gold ores often contain a portion of ‘free’ gold that is amenable to recovery using gravity concentration methods, whilst the refractory portion of the gold is better recovered using flotation. The decision as to whether a plant treating a refractory gold ore should utilise gravity concentration or a flash flotation circuit (or a combination of both) within the grinding circuit is usually made at the design stage of flow sheet development. Very limited data is available in the published literature which provides an industrial scale comparison on which to base such a decision and conventional laboratory testing methods are often the only way of obtaining such data. The optimum processing route will also be mineralogy dependent.This paper presents the findings of operating a refractory gold plant with either flash flotation (normal operation) or a combination of flash and gravity recovery methods treating the cyclone underflow stream and will demonstrate the regions of the recovery profile that each contributes to. Size-by-assay analysis has been performed on a number of streams around the operating plant to gain an insight into the changes that occur when the gravity circuit is in operation in addition to the flash flotation circuit. A discussion around the implications to overall plant operation in combining the use of a batch process (gravity concentration) with a continuous process (flotation) is presented.CITATION:Newcombe, B and Semini, D, 2014. Interactions between flash flotation and gravity concentration – an industrial case study of a refractory gold concentrator, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 427–436 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By S Natsui, Y Goto, S Kawanishi, J Takahashi, H Nogami

The demand for copper increases yearly, and further improvements in copper smelting efficiency using flash furnaces are required. This study was conducted to understand and promote the interfacial reaction associated with the collision of silica flux and iron oxide particles, ie the formation reaction of fayalite slag, in the reaction shaft of the flash furnace. High-temperature microscopy was used to observe the reaction behaviour of a 2 mm granular SiO2 reagent in contact with micrometreorder- sized FeO reagents in situ. When the amount of FeO was lower than the stoichiometric amount with SiO2, the molten slag formed at the interface between FeO and SiO2 diffused into the SiO2 particle before dissolving the remaining FeO particles. It did not contribute to the subsequent reaction, and despite having the lowest amount of FeO among the samples in this study, many unreacted FeO particles remained on the surface of the samples after testing. On the other hand, under conditions with high FeO content and close to the eutectic composition of the FeO-SiO2 system, a liquid phase formed from low temperatures, gradually increasing in volume and eventually completely dissolving the 2 mm SiO2 grain. These results indicate that the early-stage slag is essential in increasing the interfacial area between FeO and SiO2 and facilitating the supply of FeO to SiO2. In other words, the FeO/SiO2 determines the amount of liquid phase and significantly influences the subsequent interfacial reaction rate between FeO and SiO2. Therefore, the local FeO/SiO2 of the particles falling down the reaction shaft should also be optimised to ensure early slag formation. Meanwhile, the time required for 2 mm SiO2 to complete the reaction for the temperature history employed in this study was significantly longer than the particle residence time in the reaction shaft. Further detailed investigation of the effects of silica flux particle size, composition, and reaction temperature on the reaction time will help find the conditions under which the reaction of silica flux can be completed in the reaction shaft. These kinetic approaches could contribute to future innovations in the copper smelting process using flash furnaces.

Jun 19, 2024

By M S. Fenzel

Increased environmental regulations and pressures have created changing and new demands for tailings management strategies in a variety of mining applications. Critical among these items is the disposal of tailings as the pursuit of increased yields and lower costs have driven the application of different process technologies. With a number of technologies having a niche application focus, the belt filter press has been utilised for decades as a cost-effective and versatile option for dewatering different types of mineral tailings and other waste process streams. One of the critical advantages of the belt filter press is the technology’s ability to adapt and work in numerous plant designs, operating conditions and applications. As permitting and disposal options have become more stringent, plant designers, operators and equipment suppliers must develop comprehensive and site-specific economic, design and process evaluation techniques to ensure proper equipment selection and system design for belt filter presses or any other dewatering technologies. This paper will explore these techniques in relation to belt filter presses (with reference to other technologies) in a variety of different applications, along with other considerations to ensure a successful tailings dewatering system and disposal design. Summaries of equipment performance characteristics, operating and maintenance strategies and optimisation techniques will also be addressed in conjunction with the belt filter press’s adaptability to different plant designs and the resulting tailings characteristics.CITATION:Fenzel, M S, 2015. Analysis and adaptability of belt filter presses and other technologies for tailings dewatering over a range of mineral processes, plant designs, conditions, regions and operating philosophies, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 35–44 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By J Seppelt

The Kanmantoo Copper Project is owned and operated by Hillgrove Resources Limited and is situated in the Adelaide Hills region in South Australia. Mining in the area has taken place off and on over the last 140 years to recover metal from both copper and lead-zinc ores. This paper focuses on the commissioning, ramp up and future outlook for the copper concentrator at the Kanmantoo Copper Project with major focus on issues encountered and operating performance achieved to date.CITATION:Seppelt, J, 2012. Commissioning of the Kanmantoo Copper Concentrator, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 127-136 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By A S. Fogliata, L Bengochea, G Mas, J E. Lazarte

The Culampajß auriferous district is located in the northern sector of the eastern edge of the homonymous hill, Catamarca Province, Argentina. Tajo Largo mine is situated in the southern flank of Las Minas gulch at an approximate height of 3.600 m above sea level. In the studied area main outcrops are orthogneiss rocks of Chango Real Formation. The ore mineral is native gold with a lesser amount of pyrite, chalcopyrite, haematite, limonite, malachite, azurite and covellite. These ore mineral assemblages are disseminated in quartz veins filling tension fractures in the host orthogneiss.Several types of inclusions have been recognised, including three phase H2O-CO2liq-CO2vap inclusions, polyphase inclusions with H2O-CO2 and one or more solid phases, and two phase aqueous inclusions. In the three phase H2O-CO2liq-CO2vap inclusions the Tmclath is about 1¦C and the CO2 liquid-vapour homogenisation occurs at 26 - 28¦C, to liquid phase. The homogenisation temperature of H2O-CO2 occurs at 365 - 380¦C in the aqueous phase. This set of data defined a solution with a salinity of 14, 4 wt per cent NaCl equivalent and a density of 0.84 g/cm3. In the two phase aqueous inclusions the melting temperature (Tm) of -5.4¦C and the eutectic point (Te) in -38¦C indicates a salinity of about 7.5 wt per cent NaCl equivalent, with the probable presence of Ca2+. Density of fluid is about 0.83 g/cm3. Homogenisation temperature ranges between 260¦ and 280¦C. The pressure, temperature and salinity of fluids in the polyphase inclusions suggest an early fluid of high density and high salinity. The three-phase fluid inclusions may be the result of an unmixing-phase separation of post magmatic hydrothermal fluid due to pressure decrease along fractures. It is suggested that the deposit was formed during the late magmatic hydrothermal stage genetically linked to granitic rocks and can be comparable with the intrusion-related gold system of Baker (2003).

Jan 1, 2008

By D R. Wines

The design of near-surface civil infrastructure requires detailed consideration of the geological/ geotechnical conditions, excavation geometry and sequence and ground support measures to ensure stability of the underground openings and minimal impact on overlying or adjacent infrastructure. Twin parallel road tunnels have been designed and built with connecting cross passages and a piggyback busway tunnel as part of a large infrastructure project in Australia. The tunnels were excavated in poor to fair quality rocks using road headers. Temporary ground support includes shotcrete, rock bolts and canopy tubes. Extensive numerical analyses have been performed to analyse the expected behaviour of the tunnels during excavation, including two-dimensional analyses using UDEC and three-dimensional analyses using FLAC3D. Structural defects in the rock are explicitly included in the 2D analyses to examine the potential for localised ground instability. The stress redistribution is captured by the 3D modelling with an accurate representation of the complex excavation geometry and the detailed excavation and support sequence. This paper presents the modelling methodology, numerical results and discussions on integrating both 2D and 3D analyses to achieve reasonable design.

Mar 8, 2011

By P Hawke, J Hurst, B KrapeP

Hancock Prospecting Pty Ltd (HPPL) drilled two deep diamond stratigraphic holes (ECD0001 and RHD0296) within the eastern Fortescue Valley in the Pilbara of Western Australia. Located south of the Roy Hill Iron Ore project, the holes aimed to define the stratigraphy of the Marra Mamba Iron Formation (MMIF) of the Chichester Range and its south-dipping extensions below recent cover. Previous attempts to define the MMIF of the Chichester Range have resulted in differing interpretations due to the data available at the time.The unweathered MMIF beneath the Fortescue Valley in the HPPL drill holes is characterised by dolomitic carbonate interbedded with stilpnomelane-rich shales, chert and banded iron formation (BIF) with hematite staining. This intersection equates to ~75 m of carbonate-facies iron formation, as opposed to the ~230 m thick oxide-facies BIF and shale sequence encountered south of the Fortescue Valley.Various detailed geological core analyses and interpretations from ECD0001 and RHD0296 were integrated with regional diamond and reverse circulation (RC) holes from across the Fortescue Valley. Interpretation of the data indicates that the eastern Fortescue Valley MMIF represents a thinned thickness sequence of the whole formation. The MMIF of the Chichester Range and Fortescue Valley has gamma logs that correlate strongly in parts to the type section used for MMIF south of the Fortescue Valley. Therefore, the outcropping MMIF in the Chichester Range represents an eroded equivalent of the æreducedÆ thickness MMIF observed in ECD0001 and RHD0296.Data from deep diamond drill holes across the valley, from the Hamersley Basin to the Carawine Basin, were correlated. The correlation shows that the depositional site of the MMIF in the HPPL diamond drill holes is consistent with a proximal ramp setting, in which iron-rich shales wedge up-palaeoslope and shelf-derived carbonate turbidites wedge down-palaeoslope. Not only is it the occurrence of these shales that define the MMIF, but they also determine the northward potential to develop orebodies, as they are the source of iron from which iron-rich oxides and carbonates of metamorphic or diagenetic origin form.CITATION:Hurst, J, KrapeP, B and Hawke, P, 2013. Stratigraphy of the Marra Mamba iron formation within the Chichester Range and its implications for iron ore genesis at Roy Hill - evidence from deep diamond drill holes within the East Fortescue Valley, in Proceedings Iron Ore 2013 , pp 91-106 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By M Monaghan, B S. Gregory

The Geita Gold Mine is located 80 km southwest of the town of Mwanza in the north-west of Tanzania and is 100 per cent owned by AngloGold Ashanti Limited. Open pit mining commenced at Geita in 2000. In 2011, the operation produced 494 000 oz at a cash cost of US$536/oz. This is a significant improvement from 2008, when 264 000 oz were produced at a cash cost of US$742/oz.A period of relatively poor operating performance at Geita was recorded over the period from 2006 to 2009. A period known at Geita as æthe turnaroundÆ commenced in 2009, and has been remarkable to say the least. Over the last couple of years the mine has embarked on a journey, which saw various interventions and initiatives. Among the key initiatives were Project ONE (which focuses on business process framework, systems for people and safety transformation), asset integrity, fatigue management and contract mining of satellite pits.Since the commencement of the turnaround at Geita, gold production has matched market guidance. The mine has returned to positive cash flow on the basis of strong performance on cash management, improved production and increased gold price.This paper explains some of the details of the mine operationsÆ improvements, how they were implemented, their relative contributions to improved mining performance and the path ahead to best practice. Observations will be made about some improvement rules that can be applied generally in open pit mining.CITATION:Gregory, B S and Monaghan, M, 2012. The path to best practice at Geita Gold Mine, in Proceedings Eighth Open Pit OperatorsÆ Conference , pp 41-48 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 18, 2012

Since 1975 two electric hydraulic drills, a Robbins 11ND and an Atlas Copco C0P1038, have been part of the production drilling fleet at Mount Isa Mines Limited's Isa Mine. As might be expected with innovative and technically more complex machines, breakdowns and mainten- ance problems have been greater than those experienced with pneumatic drifters. This has been especially so with the COP1038 but in co-operation with Atlas Copco, many modific- ations have been made to alleviate operating problems. The training and quality of the maintenance workforce is of great importance. The use of coloured pictorial diagrams for hydraulic trouble-shooting will aid in minimising maintenance downtime. Both machines have achieved good operator acceptance. This is the result of many factors, the major ones being the more acceptable environmental conditions, the relatively low amount of physical effort and the high degree of mechanisation. The drilling area is one in which there is great potential for cost savings and product- ivity gains. Because both machines are capable of a high drilling output, Isa Mine is confident of achieving these aims.

Jan 1, 1978

By H F. Yu, S Ueda, J Diao, W F. Gu, Y Sasaki, H Qin

The main reason for the underutilisation of steelmaking slags is their instability, which is influenced by their complex phase structure. Recycling and sustainable steelmaking slag face challenges due to the presence of magnesium oxide (MgO), a crucial component in steelmaking slag. This study investigates the phase evolution of steelmaking slag during the cooling process with different MgO contents, using high-temperature experiments and FactSage™ software, ver 8.1, (by Thermfact/CRCT and GTT-Technologies) thermodynamic equilibrium calculations. X-ray diffraction (XRD) and scanning electron microscope - energy dispersive x-ray spectroscopy (SEM-EDS) analyses identified main phases in steelmaking slag, including Ca2SiO4 (C2S), RO (MgO-FeO solid solution), Ca2Fe2O5 (C2F), and Ca3SiO5 (C3S). The study reveals that RO phase increases as the MgO content increases. C3S precipitates from steelmaking slag with a 12 mass per cent MgO content at a reduced temperature of 1400°C. It is important to note that C3S remains in the steelmaking slag even after slow cooling. This may be due to the substitution of Ca2+ in C3S by Fe2+ and Mg2+ ions. Intriguingly, the precipitation of f-CaO in steelmaking slag with 10 mass per cent of MgO content occurred after one year, while there was no manifestation of f-CaO precipitation in the steelmaking slag with 12 mass per cent of MgO content even after one year. This discrepancy suggests a potential stabilising effect of an appropriate amount of MgO in steelmaking slag. However, it is crucial to emphasise that this inference lacks supporting data, necessitating further research to validate this hypothesis. The significance of this work is in uncovering the complexities of steelmaking slag behaviour, providing essential insights for optimising recycling processes. The research sheds light on the factors that influence the phase composition and stability of steelmaking slag, contributing to the utilisation of steelmaking slags, promoting environmental sustainability, and enhancing the overall efficiency of metallurgical processes in the current industrial landscape.

Jun 19, 2024

By G J. Showers, P Botman, A G. Hunt

Iron Road Limited (Iron Road) is currently evaluating the feasibility of producing 21.5 Mt/a of high-grade (>66 per cent Fe) magnetite concentrate from a 3.7 Bt resource (JORC) located at Warramboo on the central Eyre Peninsula in South Australia. Bulk concentrate can be produced via a conventional grind and low-intensity magnetic separation flow sheet. Due to the comparatively coarse magnetite liberation size (106 µm), consideration was given to enhancing both the grind economics and coarser product sizing via gravity separation.This paper outlines the test work, flow sheet design and engineering design of a gravity beneficiation circuit (GBC) conducted by Mineral Technologies for Iron Road. The resulting circuit optimisation necessitated mass balance simulation by Iron Road’s SysCAD model to quantify the resulting changes in mill recirculation load. This included the determination of project-critical grinding power and energy requirements with and without the GBC installed into the primary ball mill classification circuit. The outcome of this work was the design of a GBC, including spirals and up-current classification, which led to a substantial reduction (33 per cent) in ball mill recirculating load and power requirements, together with a favourable coarsening of final product size due to the relatively coarser gravity concentrate. This has led to a significant reduction in project design capital and operating costs. A further benefit of this approach is increased recovery of (paramagnetic) hematite and lesser titano-hematite via gravity separation compared to an all-magnetic separation approach.CITATION:Hunt, A G, Showers, G J and Botman, P, 2015. Test work and design of a gravity circuit for Iron Road’s Central Eyre Iron Project, in Proceedings Iron Ore 2015, pp 139–142 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By B Belle

"Mines around the world are inherently and operationally diverse. Current methodologies for the design of mine ventilation and cooling infrastructure involve controlling major safety and health hazards. Globally, it can be estimated that mine ventilation systems from various commoditiescirculate over 150 000 m3/s of exhaust air through shafts. Additionally, over 2 000 000 workersare transported every day through shafts in labour-intensive mining countries like China, India,Southern Africa, and the Americas. A key objective of this paper is to share experiences and provide a case for the revision of ætime-honouredÆ ventilation design parameters based on a benchmarking exercise on design exhaust shaft velocity from various global operations (gold, diamond, platinum, coal and base metals). An active fi eld observation on exhaust shaft velocity has indicated that, regardless of the commodity or continent where the mine operates, almost all life-of-mine (LOM) design parameters provided are in the same range of 20 m/s to 22 m/s, which is not convincing considering signifi cant variations exist in shaft depths, geography, commodity, operating and capital costs. From a due diligence perspective, there are no documented views that are available on the most widely used design exhaust air velocity. Based on the global exhaust shaft velocity data, it is noted that a significant portion of shaft velocities are outside the current design velocity of 20 m/s (some operating up to 30 m/s) and other signifi cant portions of the exhaust shafts operate in the critical velocity range. In the case of Australian coal mines, limited data suggests that none of the mines have ever reached the LOM design exhaust shaft velocity. It is self-evident that when the shafts are not operating at their design quantities either the mine system resistance is low or the ventilation and main fan is operating ineffi ciently. The most common reasons given for not reviewing the shaft system were, ætime-honouredÆ design parameter are being used and cannot be changed, mine fan pressure limits, possible fan blade damage, possible spontaneous combustion risks, leakage or simply did not consider such a possibility. In conclusion, the study has reiterated the historic lessons that a safe and expensive airway should not be utilised uneconomically by circulating too litt le air through it."

Jun 1, 2012

By T Leach, F Kaiqiang

The Jianchaling gold deposit is located about 1200 km south west of Beijing in central China. The deposit was discovered in 1988 by the Northwestern Geological Exploration Bureau (711 Exploration Team). Sino Gold Limited, an Australian based company, developed the mine in 1998 and is currently operating a 1000 t per day underground mine, producing about 80 000 ounces of gold per year. The pre-mine resource for Jianchaling was 1.6 million tonnes at 9.85 g/t gold. The deposit occurs within the east-west trending Mesozoic Qinling-Dabie orogenic belt formed during the Yanshanian Orogeny. In the Jianchaling region, gold mineralisation is primarily hosted by regional west-northwest to east-southeast striking faults, the most important of which, the reverse sinistral F145 fault, hosts the larger gold deposits including Jianchaling. At the mine scale, the most important zone of mineralisation is localised within a shallowly north dipping dilation on the F145 fault. Proterozoic dolomite forms the hangingwall and serpentinite and talc schist the footwall to the fault. Within the footwall, serpentinite is the most important host rock to mineralisation. Initial alteration involves replacement of serpentine to dolomite ¦ pyrite, talc to ankerite ¦ pyrite, and magnetite and chromite to pyrite, the latter locally through a transitional hematite phase. Proximal to feeder structures, the carbonate minerals have undergone partial dissolution and replacement to quartz. Gold is related to arsenean pyrite and marcasite rimming and replacement of early-formed pyrite, and associated with iron release during the processes of dolomitisation, silicification and carbonate dissolution.

Jan 1, 2004

By J Kovacs

Underground development drill and blast practices have generally remained unchanged for decades. Historically, development optimisation has focused mainly on the application of perimeter control products in order to reduce overbreak, and efficiencies in development cycle times to increase advance rates. In today’s environment of ever increasing operating costs and lower ore grades, it has become even more critical to focus on the optimisation of drill and blast in development mining. It is a crucial component in ensuring mining schedules are maintained, but more importantly achieving the objective of getting to the orebody in the shortest possible time.This paper will focus on the development optimisation process used in a trial at Xstrata’s George Fisher Mine in North Queensland. Not only did the trial include the typical optimisation areas of charge loading practices, perimeter control methods, drill design standardisation and quality control processes, it also investigated the significance of delay accuracy with regards to perimeter control and drill design optimisation.One of the key measures of the trial was a comparative analysis between baseline development and development with the staged introduction of optimisation elements using 3D photogrammetry as a validation tool. A detailed cost analysis between the various stages was also a key measurable of the trial.The results of the work undertaken at George Fisher have shown that the accuracy of electronic detonators can produce significant benefits in development blasting. When combined with standard optimisation philosophies a substantial reduction in overbreak, ground support requirements and development cycle times can be achieved, whilst still being able to reduce the overall development operating costs.CITATION:Kovacs, J, 2014. Mine development optimisation – an evolutionary process, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 51–56 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By D Howe, J Conn, J G. McLellan, K Gates

The Red October Gold Mine, owned by Saracen Gold Mines Pty Ltd, is located approximately 80 km south of Laverton, Western Australia. It is considered to be of a similar nature to many of the Archaean granite-greenstone deposits in the Laverton Tectonic Zone, and presents as an intriguing and relatively young deposit in terms of developed structural and genetic models. Regional deformation events have been proposed for the area, and are relatively well accepted. The most important of these deformation events in the region were the D4b (WNW–ESE sinistral transpression) and D5 (ENE–WSW dextral transpression) which have been attributed to the main Au mineralising phases. At the local scale there appears to have been a rotation of the regional stress field to provide the optimum orientation of maximum principal stress for sinistral movement on the main shear zone.Fully coupled 3D finite element analysis (FEA) was used to simulate the geomechanical response of the system based on structural observations. The geomechanical modelling resulted in highlighting anomalous patterns of stress and strain and subsequent fluid flow as a result of the two main deformation events. The D4 simulation provided a good correlation with the known distribution of subsidiary structures on the main shear zone, and furthermore provided several geomechanical targets that suggested locations of additional subsidiary structures. The D5 simulation provided a great insight into the response of the main shear zone and known subsidiary structures also highlighting additional targets indicating potential for further mineralisation. These targets have since been followed up with a 732 m deep surface reverse circulation (RC) drill hole, resulting in the discovery of two high-grade shoots, with follow up testing currently planned for mid-2014.CITATION:McLellan, J G, Conn, J, Howe, D and Gates, K, 2014. Structural controls and strain partitioning in the Red October Gold Mine, Western Australia, in Proceedings Ninth International Mining Geology Conference 2014 , pp 315–322 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By S Long, D Carnovale, L Louwrens

The Mt Wright underground mine (MTW) is located near the town of Ravenswood in north Queensland and is operated by Carpentaria Gold – a wholly owned subsidiary of Resolute Mining Limited.The Mt Wright mine has gone through many stages, from the conception and implementation of the world first ‘sub-level shrinkage’ stoping (SLS) with continuous fill mining method in 2010, through to steady state production. These have been outlined in detail in papers presented by Mackay (2011) and Mackay, Long and Koen (2014) at previous Underground Operators Conferences.Since the last paper was presented, MTW has experienced significant change in two key areas.The first significant change was the discovery of a previously unknown hazard in the form of flat rilling events (FREs) from closed drawpoints (DPs). These events are believed to be unique to MTW and pose a significant risk to both the safety of personnel and the business as a whole. The paper will discuss this hazard and the evolution of the controls and practices that have been introduced to mitigate the risk posed by the identified hazards. The material involved in these events is extremely dry, fine and hot.The second significant change is an altered stress regime bought on in part by a change in the production front orientation and a general deterioration in ground conditions in some areas of the mine. This has caused some production interruptions at MTW. The second half of the paper will describe the challenges encountered, the mechanisms behind these challenges and the strategies implemented to safely return MTW production to planned levels.It is believed that other operations can learn from the issues mentioned above, and the paper has been written with this in mind.`CITATION:Long, S, Carnovale, D and Louwrens, L, 2017. Mt Wright – managing unique risks, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 295–304 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017