Search Documents

By Rosengren KJ

Geotechnical conditions often have a critical influence on the design of new open pit and underground mines, but they are often considered of secondary importance in relation to other factors, such as detailed geology, orebody geometry and grade distribution. As a result, geotechnical studies may not be carried out during early project investigations or, at best, may be given only superficial attention, often to the overall detriment of the project. Technically and economically, it is logical that geotechnical studies should be integrated with geological investigations as soon as it becomes evident that the particular deposit may prove to be economic. The paper discusses the use of geotechnical information in the selection of mining methods and mine design for underground mines and for wall design and assessment of excavation characteristics in open pit mines. It then considers methods of obtaining the relevant data, with particular reference to exploration boreholes. Selected case studies on the application of geotechnical data to mine design are Included.

Jan 1, 1986

By Hochwimmer B, Baxter JL

Heavy minerals are mined from two fossil strandlines on the southern Swan Coastal Plain. The Capel shoreline, 7 km inland, and the Yoganup shoreline, 15 km inland are arcuate, northwest-facing, and remote from the modern coast. Based on foraminiferal and molluscan assemblages, the shorelines are probably of Pliocene age. The Yoganup shoreline is adjacent to the Whicher Scarp, which is cut into the Leederville Formation (Lower Cretaceous) at the southern boundary of the Swan Coastal Plain. Stratigraphic relations and detailed sedimentology have been studied from temporary exposures in the Yoganup Extended and Yoganup North mines, within a strandline complex at 27 m and 18-33 m above sea level respectively. Heavy minerals were deposited in thin, shallowing-upward sequences along a wave-dominated clastic shoreline cut into pre-Cainozoic sediments. Lithofacies units deposited in eolian, foreshore, shoreface and lagoonal environments are the most significant sites of heavy mineral accumulation. The data collected provide a basis for further exploration.

Jan 1, 1986

In 1972, metallurgical testwork on Renison ore indicated a significant proportion of low specific gravity, tin-barren material ideally suited to heavy medium separation (HMS). Further technical and financial studies provided adequate economic justification and in December 1974 the Renison HMS plant was cannissioned. Initial operations were interrupted by the imposition of tin production quotas for three months in 1976; they were also beset with difficulties particularly with regard to mechanical wear. During the first two operating years much develognent work was carried out including installation of a pyrrhotite flotation bank in the medium recovery circuit, investigations into various wear-resistant materials and the use of atanised rather than milled ferro-silicon. By 1977/78 financial year satisfactory performance had been achieved and since then the average floats rejection has been 18.8% of the total ore treated with an associated tin loss of 2.96%. Developnent has nevertheless continued during the last three years, principal modifications being the installation of larger aperture desliming screens and improvements to the overdense cyclone circuit.

Jan 1, 1978

By Rowena C. Duckworth

The Ocean Drilling Program (ODP) is the largest international geoscience project in the world, and the state-of-the-art drill ship, the JOIDES Resolution, is permanently at sea. Each year there are six scientific cruises (legs) which each last approximately two months. These legs are designed by geoscientists from the nineteen countries that subscribe to ODP. Australia and Canada presently share ODP membership under the banner of the AUSCAN Consortium. The benefits of Australia's involvement in ODP include internationalisation of Australian geoscience, advanced graduate training, and unique scientific investigations of the ocean floors in the Australasian region. In addition, visits to Australian ports by the ODP drill ship, the JOIDES Resolution, contribute up to $2 million per visit to the local economy. Amongst the many other aspects of ten years of scientific drilling, ODP has significantly contributed to our understanding of hydrothermal processes on the seafloor. To date, three hydrothermal sites have been drilled to date by the ODP, Snakepit (MAR), Middle Valley (Juan de Fuca Ridge) and TAG (MAR). Two more hydrothermal sites are scheduled for 1996.

Jan 1, 1995

By Hayward SB

The Maragorik prospect is an example of high sulphidation, Cu/Au mineralisation occurring at a high level in the hydrothermal system. As extensive ash deposits blanket the region, controlled-source audio magneto-tellurics (CSAMT), in conjunct-ion with bulldozer trenching, have been used to delineate subsurface geology. Fluid upflow has occurred along EW structures dilated by rotation on the bounding major NW lineaments. Rising hydrothermal fluids have exploited permeable horizons in contact with the upflow structures. This lithological control is evident as ledges of silicification and peripheral clay alteration, at high levels in the system. As is typical of high sulphidation systems, a two phase fluid consists of an initial rapidly moving vapour-dominated phase, followed by a liquid-dominated phase. Much of the zoned and overprinted silica to clay alteration is developed from the vapour-dominated fluid. Mineral deposition occurs as a result of brecciation of the competent silic-ification by liquid phase fluids. Such mineralisation is of restricted volume in ledges proximal to the feeder structures.The style of alteration and mineralisation are indicative of a very low temperature and hence a high level system. Thus, although high sulphid-ation systems are inferred to develop from porphyry-related magmatic fluids, such a source at Maragorik is interpreted to be very deeply buried.

Jan 1, 1994

Evolutionary changes to the original sizer concept are mild when compared to those which have taken place in the engineering standards embodied in today's commercially available machines. This paper examines the principles of sizer operation and reviews the development trends in new applications for this unique screen type.

Jan 1, 1978

By Ahmed M, Leung L

A program of microseismic noise monitor ing for gas outbursts, in conjunction with other mining engineering measurements and observations, is being undertaken at Leichhardt colliery in Queensland. Headings are developed at present by shotfiring. The equipment being used in this study includes piezoelectric accelerometer assemblies to detect microseismic noise which is then transmitted to a surface base station by cable. Data are recorded on an analogue magnetic tape recorder and are also analysed on-line using a commercially-available acoustic emission pulse analyser. It is proposed to re-interpret recorded data using various modes of analysis and to interface a desktop computer to the existing system to permit continuous monitoring on the mine site. No outbursts have been recorded or analysed and only a limited number of develop- ment shots, and the resultant microseismic activity, have been recorded to date.

Jan 1, 1980

By Mercer J. K

Shaft guide reaetions in No. 2 Ore Shaft, Mount Isa Mines Limited, have been reduced to a low order of magnitude by the use of self aligning slippers and spring loaded guide rollers. Before commissioning the new 4500 h.p. winder at No. 2 Ore Shaft in January, 1958, it was realised that the increase in hoisting speed from 1800 to 2650 ft/min. would cause high shaft guide reactions which would be increased further when the elongated 12 ton skips replaced the existing 7 ton skips.The Cambridge accelerometer was used to measure the shaft guide reactions and to confirm that progressive skip modifications were resulting in reduced reactions. The skip modifications were completed in 4 weeks.INTRODUCTIONIn 1956 an expansion programme was initiated to increase production from 5000 to 11000 tons per mining day. At No. 2 Ore Shaft the 1500 h.p. winder operated at 1800 ft./min. and hoisted a 7 ton capacity skip. The new 4500 h.p. winder operates at 2650 ft./min. and hoists a 12 ton capacity skip. No. 2 Ore shaft is equipped with two 5 ft. by 5 ft. hoisting compartments (Fig. 1) and any increase in skip capacity meant an abnormally long skip. This feature, coupled with the increase in hoisting speed, could have caused very high shaft guide reactions. Before commissioning the 4500 h.p. winder, a Cambridge accelerometer was borrowed from the University of Adelaide and was used to measure the shaft guide reactions. Rather than carry out an extensive shaft timbering programme, the skips were modified by fitting cushioned guide shoes and spring loaded guide rollers (Fig. 1). Testing commenced in February, 1958, and was completed in March, 1958.

Jan 1, 1961

By Knasmillner

During blasting body wave interaction with geometrical surfaces induces Rayleigh-waves which propagate along free surfaces, e.g. crack faces or delaminated rock layers. These Rayleigh-waves carry most of their energy within a very shallow surface layer and propagate with very little attenuation in real rock materials. Upon interaction with a crack front a very strong mixed mode stress intensity factor may result and lead to fracture initiation. On the basis of experimental photomechanical results the history of dynamic stress intensity factors Kt and K2 will be studied in Detail.

Jan 1, 1990

By Nott M. C

The oxidation of xanthate collectors to xanthate/dixanthogen results in a higher hydrophobicity of sulphide minerals surfaces due to the action of dixanthogen. This higher hydrophobicity can be proved on a fundamental level by examining the st

Jan 1, 1994

Lungfish and crayfish inhabit continental ecosystems similar to those of their ancient counterparts in the Permian (lungfish) and Triassic (crayfish) Periods, exhibiting similar burrowing behaviors to live, breed, and escape desiccation. Identification of their burrows in the geologic record when body fossils are absent has relied on the overall gross morphology of the burrows and the process of elimination. A method of burrow identification has been developed by evaluating burrow structures in an attempt to designate architectural and surficial burrow morphologies that uniquely reflect the distinctive burrowing mechanism of a particular organism. The information from this method defines the burrowing signatures of an organism, enabling the differentiation of their burrows even when fossil evidence is lacking.The lungfish constructed simple, vertical burrows with bulbous terminations. The burrow walls exhibit fine, horizontal to sub-horizontal striae and vertical to sub-vertical striae near the top of the bulbous terminus, reflecting a burrowing style similar to modern burrowing lungfish. The crayfish constructed simple, vertical burrows to complex burrows with multiple branching and chamber development. The burrow surface ornamentations exhibit horizontal to sub-horizontal ridges, vertical to sub-vertical groupings of scratches, mud- and lag-liners, knobby and hummocky textures, and body impressions, which reflect the burrowing mechanism of the crayfish.

Jan 1, 1990

The late 1960's and 1970's saw the initial development of the coal resources of the Bowen Basin of Queensland. The projects developed relied on large scale, open-cut operations using draglines for overburden removal and, in the majority of cases, project viability could be established based solely on those open-cut operations. Many of the mines developed in the 1980's have the same characteristics.Unlike these mines, the German Creek Mine has limited open-cut reserves at low overburden to coal ratios, and planning of the complex involved a large open-cut mine capable of developing early cash flow, with phased introduction of underground mining to replace open-cut capacity as the strip ratio increased.

Jan 1, 1985

The major copper orebody at Mount Isa is being extracted at a rate of four million tonnes per year. The method used requires an equivalent rate of back filling with (mainly) cemented fill. There were three major incentives for developing this mining system. The first was the prospect of high ultimate recovery of the orebody. The target is 100% recovery. Also the proposed stoping layout appeared to offer significant advantages in development and production costs. Finally, extensive subsidence above the northern end of the orebody could have disturbed permanent surface installations and jeopardised a possible future open cut. The full implications of this ambitious strategy were not apparent in the early years. Now, after twelve years of production the benefits are being realised and they can be weighed against the costs. Probably the most interesting result which comes from this analysis is the significance of cutoff grades and dilution factors in balancing mining and filling rates.

Jan 1, 1980

By Yagi Y

The double track railway tunnel, called the Second Shirasaka Tunnel is being constructed under the supervision of Japanese PTational Rail- ways (JNR) in the tertiary soft rock strata in order to speed up the railway transportation. This tunnel (L=1765m), located in a central part of Japan, is excavated by the machine (roadheader), while the adjoining First Shirasaka Tunnel (L=1296m), completed five years ago, was driven by the blasting, and NATM is adopted in both tunnels. The geological features in this region are Neogene Tertiary of Miocene sediments consisted of mudstone, the sandy mudstone and the alter- ation of these rocks, having a squeezing be- haviour. And the geological structure is as complicated as some anticline and syncline structures, large or small scale exist, and as a lot of faults are found. The machine excavation manner using road- header is adopted in this tunnel to minimize the effect of excavation because there is a possibility of the occurrence of landslide due to the tunnel excavation, and also because local inhabitants reside on the ground surface.

Jan 1, 1987

By Walker K, Burton RC

An outline of the ventilation and refrigeration requirements of deep South African gold mines is presented. This is followed by a brief description of the history of controlled recirculation in mines and the practical and economic benefits such schemes can offer. The potential hazard of a fire in a recirculation system is discussed.The major part of the paper describes the first large-scale field trial of controlled recirculation to be conducted in South Africa. Emphasis is placed on the monitoring system that was used for data acquisition during the trial, and also on a safety system designed to shut off the recirculation fans in the event of a fire.The paper concludes with a review of the latest development work taking place on recirc-ulation safety systems.

Jan 1, 1985

By Baird G. R, Jurak R. N

In this study Dynamic Finite Element Modelling is used to investigate the distribution of peak particle accelerations (PPA) induced in a rock mass by a vertical decked column of explosives. The rock mass is assumed to be viscoelastic. The influence of the delay time between decking charges, the viscosity attenuation (quality factor Q), the decking configuration, and the velocity of detonation (VOD) on PPAs is examined. The results of this paper are relevant to fragmentation since the nature of the fragmentation is related to the stress magnitude and hence the PPAs. It was found that increasing the VOD, and increasing Q increases the PPAs in the neighbourhood of the blasthole. However, the VOD and rock quality factor Q have little influence upon the distribution of PPA. It was also found that an even distribution of PPAs, at a fixed distance from the blasthole, could only be obtained by increasing the ratio of charge length to stemming length. The study showed that the amplitudes and distribution of PPA surrounding the blasthole was approximately independent of the delay time between the decked charges. The modelling also shows that the particle accelerations at locations below the bottom of the charge are relatively small and so the model predicts no substantial damage below the bottom of the charge after blasting.

Jan 1, 1995

By L Bergin, D J. Williams, S Islam, T A. Vangsness

The flooding of open strip coal mines in the Bowen Basin and Hunter Valley Coalfields of Eastern Australia has the potential to soften the spoil and floor materials to produce “mud”. This mud can act as a slip plane or weak zone when spoil is dumped into it, resulting in geotechnical instabilities. Once mud has formed, typical handling techniques include its costly removal by mechanical means, or its isolation and capping.There are little data available on the moisture state and shear strength of the capped mud. To investigate the effectiveness of isolation and capping, research has been conducted using a large slurry consolidometer (150 mm in diameter by up to 410 mm in height) to simulate capping in situ. Once consolidated, the mud was subjected to shear strength testing in a direct shear box measuring 60 mm by 60 mm by about 20 mm high. The shear strength of the consolidated mud was compared to that of competent, fresh spoil, a mixture of spoil and mud, and to completely degraded spoil (mud alone).These results have been used as inputs in stability calculations using the commercial computer program Slide 7.0, which demonstrates the strong influence of consolidation of the mud on overall low wall slope stability. The results provide insight into the design and construction of capping to isolate in-pit mud.CITATION:Vangsness, T A, Williams, D J, Islam, S, Smith, A and Bergin, L, 2018. Consolidation and shear strength testing and stability analysis of coal mine spoil degraded to mud, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 97–109 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By M G. Hawtin

The Rocklands copper project is a multilode, iron oxide copper gold (IOCG) + cobalt mineralised system located in the Eastern Fold Belt of the Mt Isa Inlier. Rocklands orebodies cover a range of oxidation zones from oxide, to supergene and primary. Each zone contains different economic minerals of interest. The supergene zones contain significant amounts of native copper and the primary zones are dominated by chalcopyrite. The juxtaposition of these oxidation zones and minerals make it an interesting mineralisation system.Current mine production sampling collects a nominal 3 kg drill chip sample from a 1 m composite, RC drilled interval. A site specific sampling procedure was needed to quantify introduced sampling error when taking grade control samples. Due to oxidation and mineralogical variation in ore zones we needed to develop a practically achievable sampling methodology that ensures minimum sample mass and sample error requirements are achieved to ensure ‘representative’ samples for all ore types.These issues are planned to be resolved using an experimentally derived method using principles from the Theory of Sampling. This method uses an experimental calibration of parameters K and a for Gy’s fundamental sampling error formula using a modified 32-piece sampling tree experiment to compile sampling nomograms for the primary and supergene ores. This paper demonstrates the process undertaken to improve the quality and standard of existing mine production sampling procedures at the Rocklands operation.Results indicate a sample mass of 5 kg for RC drill chips is appropriate for both the primary and supergene ores to achieve a fundamental error below 0.01 or 10 per cent relative error, which is slightly higher than the existing sampling protocol of 3 kg. An additional experiment is recommended to compile sampling nomograms using the exact laboratory comminution and mass reduction stage information to assess the use of a 3 kg sample. The results also indicate no changes are required to existing sampling protocols when sampling RC drill chips in primary and supergene ore at Rocklands.Sampling nomogram results also provide a useful ‘rule of thumb’ reference guide to other mining and exploration companies to help understand minimum sample mass requirements and sampling error during exploration drilling, resource evaluation and mining production stages when targeting similar IOCG mineralised systems. A sample mass of 5 kg is recommended when RC drilling similarly IOCG mineralised prospects and deposits in the Cloncurry area. Future test work is recommended when additional open cuts become active as well as including resource drilling drill core to provide better three-dimensional sample representivity.CITATION:Hawtin, M G, 2017. Minimum sample mass from reverse circulation grade control drilling at Rocklands copper project, in Proceedings Tenth International Mining Geology Conference 2017, pp 337–346 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By D J Maconochie

The use of rock bolts as permanent support has been prohibited by client specifications in several recent large tunnel projects in Australia. The justification for this appears to lie in concerns with proper and verifiable installation procedures rather than concerns with the intrinsic durability of the corrosion protection systems. However, in civil tunnels, preventing the use of permanent rock bolts for long-term support results in the use of cast in place concrete lining which in some instances would otherwise be unnecessary.

Mar 8, 2011

By Xaykhamphoune, Ward B

Draglines have been used exclusively for primary overburden stripping at the German Creek Mine complex in central Queensland, where coal has been extracted from a series of ten open cut pits working seams of the German Creek Coal Measures. Due to the dip of the seams, most of the pits have now reached the limit of current economic viability and the emphasis has switched to underground extraction using longwall methods and to a new area of open cut reserves in the nearby Rangal Coal Measures at German Creek East. This area is characterised by weak Tertiary overburden, relatively steep dips and low strength intraformational shear planes at the top and bottom of the coal.The first pit, with a maximum depth to coal of 15 m at the low wall, avoided any major slope failure through use of scrapers to excavate the boxcut and dump the spoil away from the low wall. However, this method was not considered economically viable for the second pit where low wall depths reached 44 m. Following geotechnical investigations the boxcut was divided into a number of zones depending on depth of cover, dip and thickness of Tertiary clay. Slope stability was assessed for each zone using several analytical techniques to ensure that dragline mining would be acceptable. Slope design parameters incorporating various stabilisation techniques, notably an updip trench backfilled with competent spoil to form a low wall buttress prior to excavation of the boxcut panel, were successfully integrated into the mine plan after careful consideration of the complex scheduling to minimise rehandle.

Jan 1, 1992