Search Documents

The man in the street (and no doubt most members of the Institute) thinks of wire, if he gives it any thought at all, as a most commonplace commodity. It is an accepted necessity, and like most necessities is taken for granted, unless a shortage in one or other of its multitudinous forms or products causes inconvenience.For many years Australia has ·been a large consumer of wire, particularly for fencing. With the rapid development of secondary industry the demand has increased in both size and character until at the present time much of the wire produced in this country is used as raw material for subsequent manufacturing processes. The call has been of so varied a nature that the Newcastle Wire Mills now turn out a greater variety of wire types than any other single plant in the world.In this paper, the aim is to provide a picture of the manufacturing, properties, and uses of wire. No attempt is made to cover the subject in any detail, as the field is much too broad for anything other than general treatment. Many phases, particularly in regard to manufacturing processes, are, therefore, dealt with cursorily, but it is hoped that the paper will, without delving too deeply into the technical aspects of Wire production, give a general appreciation of:- (a) How steel wire is made. (b) The remarkable physical characteristics obtained by judicious combination of chemical composition, heat treatment, and subsequent cold work. (c) The uses of steel wire.HISTORY.Best known of the early references to wire is that appearing in Exodus, where mention is made of gold wire being used for the sacerdotal robes of Aaron. However, the period in question, about B.O. 1491, is comparatively modern history as far as wire is concerned, for specimens believed to have been made about B.O. 4600 have been found. It is fairly certain that the Egyptians produced iron wire in B.O. 4000. Of particular interest is the

Jan 1, 1947

By H Khoshrou, A Siamaki

Blast designs can have productive and non-productive impacts on downstream stages, mine productivity and operating costs. On the other hand, ground vibration, fragmentation, and back break caused by blasting impose damage and financial penalties and which must be controlled by blast design. One of the significant variables in blast design is the burden. In this study, the potentials of artificial neural network are investigated in prediction of burden in the Sungun copper open-pit mine. Input data were assembled through 18 blasting blocks according to different levels and experimental geomechanical investigation. To construct the model blastability index, uniaxial compression strength, hole diameter, specific weight of rock, rock quality designation and cohesion strength are taken as input parameters, whereas, burden is considered as an output parameter. Mean square error was used as the performance function and back propagation algorithm as the training function, containing four hidden layers and 14 data sets. Four sets of data were used to make sure that correct training had been carried out. This produced the coefficient correlation of 0.662.

Sep 26, 2011

By R McIlwraith, B Breul

"This paper discusses the successful use of bituminous geomembranes (BGMs) in mining applications since their development in 1974. It explains and illustrates the structure of a BGM composite, which is a geomembrane manufactured by impregnating a polyester geotextile with a compound of bitumen, elastomer and filler. Examples of applications of BGMs in the mining industry are also presented in the following contexts.Storage of solid waste: storage of mining waste at mines in Canada heap leach pads in France, Peru, Chile and Turkey at the base of a mining waste landfill in Brazil capping of solid mining waste in Chile and Canada temporary capping of mining stockpiles in Australia (with possible reuse of the BGM for other works).Examples of the application of BGMs for the storage of liquid waste in mining containment reservoirs in Canada, Guatemala and Peru will also be given.For each example given, reasons are supplied that supported the choice of BGMs by the clients and consultants, drawn from the following advantages of the BGM:BGMs have excellent puncture strength, due to the internal polyester reinforcement, as well as excellent ultraviolet resistance. This often eliminates the need for a cushion geotextile or cover soil over the BGM.BGMs have a very long life expectancy, in excess of 300 years, in subsoil conditions (Breul et al, 2004).BGMs can be installed in very harsh climatic conditions. They are suitable for high wind environments as their heavy mass per square metre makes them resistant to wind uplift. The low coefficient of thermal expansion means that BGMs are suitable for installation in mines where very low or very high temperatures are expected. This reduces construction delays and allows for a quicker use of the mining facility.The fact that the BGM can be installed by the mine’s own workforce, after appropriate training from the BGM manufacturer, allows for a more flexible construction sequence on the mine.Ability of the BGM to connect to other materials such as concrete, steel, rock and other geomembranes that may be on the mine site.The technical advantages of a BGM enabled the engineering consultants to prepare solutions for their mining clients that had a lower environmental risk, had a faster completion schedule and were overall a cheaper option than with a polymeric geomembrane.CITATION:Breul, B and McIlwraith, R, 2015. Bituminous geomembranes in mine construction, in Proceedings Tailings and Mine Waste Management for the 21st Century, pp 289–296 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 27, 2015

By J Coombes

The JORC Code lists the three core principles of Transparency, Materiality and Competency as fundamental to how mineral estimates are publicly reported. But where the principles of Transparency and Materiality can be considered conscious choices underlying decisions at the point of disclosure, Competency is a self-declared position statement based on one’s confidence to defend a technical position (as well as the functional pre-requisites of institute membership and a minimum of five years relevant experience).Developing competency in the mining industry is an ad hoc process, generally left to the individual to chart through a process of osmosis from personal work experiences that lead to a sufficient level of confidence. Companies that actually present professional development programs leading to reporting competency are rare. And even once a person has followed a program, there is no specific outline of what constitutes technical competence.No doubt, there are persons signing off on mineral statements who would benefit from developing and/or updating their technical skills (they may not even be aware of unmastered skills). Equally, there are technical practitioners who are sufficiently competent, but lack the confidence to step up and publicly report their estimates. Confidence in one’s own abilities plays a significant role in deciding when one is ready for the responsibility of submitting mineral estimates for public consumption. In addition, a person’s organisational support, such as the availability of suitable peers and professional development programs, and opportunities to learn from a variety of technical projects contribute to developing relevant experience. Increased exposure in both technical breadth and depth enhance confidence in one’s ability and competence.The mining industry provides numerous opportunities through direct and indirect means to develop the competency underpinning a stable reporting code. This paper examines a theoretical framework and associated processes that could be used to examine how the mining industry, companies and individuals collaborate to develop this vague principle of competency. This paper seeks to initiate research with the express purpose of enabling more effective and efficient development of reporting competency in our industry.

Aug 22, 2011

The knowledge in the field has been reviewed by literature studies, and using experience from personal research in sublevel caving. There is a lot of material regarding gravity flow of fine grained materials in bins, but the theory of flow for these materials are normally not applicable for coarse blasted rock. This study was therefore concentrated towards coarse rock fragments created after blasting in orebodies. The goal for this study was to make a report of known knowledge, and identify what we have to learn more about. The Bergmark-Roos theory, which was a paradigm shift in the science of gravity flow, is today the best mathematical theory for calculation of the drawbody for a homogenous material or when we wish to simulate the mean drawbody for a large number of draws. The Bergmark-Roos theory must however be improved, so it can take into account the flow pipe effect. When this is done it will be possible to construct a 3D computer model for calculation of ore extraction versus amount of loaded ore and waste. It is also necessary to find the 3D shape of the flow cone to be able to calculate the 3D ore rest that normally develops on footwalls. Calculations should be done for the draw on several sublevels including determination of the ore losses and temporary ore rests. First when this computer model is developed optimisation of ore recovery and waste rock dilution can start for a given orebody. The author points out the importance for international co-operation and standardisation of methods for determination of material properties. More field tests and model blasting tests should also be done. When enough knowledge is gathered, a handbook of the optimisation of sublevel and block caving should be written.

Jan 1, 2000

The Barmac autogenous crushing mill is one of the most successful new comminution technologies to become available to the mining and industrial minerals industries in this decade.The Barmac autogenous crushing mill is an innovative Vertical Shaft Impactor which operates in essence like a high intensity dry ore centrifugal pump with the reduction occurring primarily as a result of high velocity rock to rock impact in a fully rock lined crushing chamber. With applications in a wide range of mining and industrial minerals operations the Barmac autogenous crushing mill presents an opportunity to enhance reduction and liberation whilst providing many cost savings and production increases in new and existing plants.This paper briefly describes the operation of the Barmac autogenous crushing mill and reviews its benefits.

Jan 1, 1990

By S Kakara, A Kamaraj, S S. Varanasi, B V. R Mandalika, M B. Shaik

The properties of top slags play a very important role in secondary steelmaking. Fluxes should be chosen based on the ladle furnace (LF) slag requirements like viscosity, melting temperature, sulfide capacity, etc. CaF2 and CaO-Al2O3-based synthetic slags are the most used fluxes in secondary steelmaking to improve slag fluidity and interfacial chemical reactions. CaF2 is obsolete due to fluorine pollution and CaO-Al2O3 based slags have 40–50 wt per cent Al2O3 and 30–40 per cent CaO which is not beneficial for desulfurisation. Yet another drawback is that LF slag disintegrates into fine powder during cooling due to phase transformation C2S (2CaO.SiO2). Hence, there is a need for the development of low melting fluxes with high CaO content and the capability to prevent slag disintegration. The current work studied the effect of 0–9 wt per cent B2O3 on physico-chemical properties and characterisation of LF slags. X-ray diffraction (XRD) analyses were carried out to identify mineralogical phases present in slag and Fourier-transform infrared spectroscopy (FT-IR) analysis was done to understand the changes in bonds of B2O3 added LF slag. The characteristic temperature of slag was determined by a hemispherical method using high-temperature microscopy. Empirical models were used to calculate viscosity, break temperature, and sulfide capacity. FactSage™, ver 8.2 (by GTT-Technologies) simulations were carried out to find the equilibrium phase fractions and percentage of liquid slag at different temperatures. New phases such as Ca11B2Si4O22 and Ca2B3O5 were formed in LF slag with B2O3 addition. Based on the results, 0.5–1.0 wt per cent B2O3 was found to be sufficient to prevent C2S-driven disintegration of LF slag. Also, the melting temperature and viscosity of LF slag were reduced by adding 3–8 wt per cent B2O3 due to the formation of BO3 planar triangular structure and low melting eutectics in slag. Liquid slag started forming at a temperature as low as 800°C when B2O3 is >6 wt per cent. It was found that the sulfide capacity, viscosity, and break temperature of the slag decreased with increasing wt per cent B2O3. Based on the analysis carried out, B2O3 can be a promising fluxing material in secondary steelmaking, for improving the desulfurisation kinetics and valourisation potential of LF slag.

Aug 21, 2024

By N Maistry, C Carelse, A Singh

Banded Iron Formations or more commonly known as BIF are sedimentary rock formations with alternating silica-rich layers and iron-rich layers that are mainly composed of iron oxides (hematite and magnetite), iron-rich carbonates, and/or iron-rich silicates. Considering the depletion of highgrade iron ore reserves in South Africa, there is a need to maximise resource utilisation through the exploitation of low-grade/uneconomic resources particularly BIF material, which makes up more than 65 per cent of current reserves. Previous test work conducted by alternative BIF sources globally indicates the need for fines processing in order to produce a concentrate. South African BIF however is amenable to coarse and fines processing producing an on-grade product or blended feedstock. C-Type material within South Africa’s Northern Cape Province grading at approximately 33 per cent Fe was supplied for research purposes. Top size optimisation via gravity Heavy Liquid Separation (HLS) tests was conducted. The laboratory results being perfect separation (Ep=0) were modelled to predict pilot performance, the results of which were tested on a pilot scale for the finest size fraction (-1 mm). It was observed that a top size of -2 mm provided optimum results in terms of upgrade and recovery, with crushing finer not necessarily producing superior results. At a target grade of 60 per cent Fe, recoveries of 65.6 per cent were achieved on the laboratory scale, whilst recoveries of approximately 58 per cent were achieved on the pilot scale. Targeting higher upgrades of 63 per cent would inevitably result in lower recoveries of 57.2 per cent on a laboratory scale and approximately 54 per cent on a pilot scale. This is in line with grades and recoveries achieved globally for BIF material albeit at finer grind sizes.

Sep 18, 2023

By B Roache, J O’Brien, M Gray

Admixture use in cement products is commonplace in the construction and mining industries. Many Australian mines have an operational concrete batch plant and stock hydration control and water reducing admixtures. The benefits of admixture use, especially in shotcrete is understood and well documented. Cemented rock fill (CRF) is used to fill stope voids and create stable vertical and undercut surfaces at some Australian mines. These mines generally mix rock fill with a slurry of cement and water without the use of admixtures. Recently published work on optimisation of CRF mixes has mainly focused on the strength increases associated with changes to the mix grading proportions by the addition of fines, but not focusing on the potential benefits of admixture use. Admixture use in CRF may be the simplest CRF optimisation method, as the admixtures will often be added by the push of a button at the batch plant. A CRF testing program was undertaken to test the benefits of admixture use in terms of strength gain, using hydration control additives (HCA) and high range water reducer (HRWR) admixtures. Rock fill gradings were strictly controlled in the test process to allow clear definition of the difference admixtures provide in compression at 28 days. The testing results define admixture associated strength gains in a 6 per cent general purpose (GP) cement by dry weight CRF mix (131 kg of cement/m3). Costings have been developed to allow a mine operator to understand the cost benefits of admixture use in CRF due to reduced operating costs. Operational efficiency advances and a suggested admixture implementation plan for CRF optimisation is offered.

Nov 29, 2022

By Morley I. W

In the year 1926, Edie Creek, in the Morobe District of the Mandated Territory of New Guinea, saw the greatest gold rush of recent years. Situated 35 miles inland from the coast, and at an altitude of over 6000 feet, Edie Creek presented to the original prospectors a wet, jungle-clad uninhabited, and inhospitable region. There were no roads; and the only means of approach from the equally inhospitable coast was by an eight to ten days' tramp through coastal swamps and gorge-scarred mountains. All food supplies and equipment had to be carried on the backs of "kanakas," and in many cases through country occupied by hostile natives.Since the first discovery of payable gold at Edie Creek, mining on the Morobe Goldfield has shown remarkable progress, and in spite of the tremendous natural difficulties, the field today ranks as one of the most important in Australasia.Aeroplanes, more than any other factor, have been responsible for this rapid development. They provide the only means of transport from the coast, and at present serve the needs of over 600 Europeans and 3000 indentured native labourers engaged in the industry.

Jan 1, 1933

Subsurface development requires some geotechnical conditions and challenges. Most of then are related to the compatibility between tunnelling system and surrounded ground conditions, and design criteria. Design criteria usually involve lining pressure and ground control of displacements. In order to fulfil these requirements, geotechnical parameters have to be obtained as well as construction aspects have to be taken into account for predicting the tunnel behaviour. The Brasilia Metro is presented as a case history illustrating the geotechnical conditions and challenges for its implementation. It is 42 km long, including tunnels excavated in collapsible porous soils by the New Austrian Tunnelling Method. The Brasilia porous clay presents some characteristics, which may lead to large deformations due to structural collapse. Empirical methods were calibrated for collapsible porous soils and then applied to predict tunnelling-induced settlements. Settlements due to soil structural collapse modify completely the expected settlement profile, increasing their values from the tunnel crown to the ground surface. Consequently, surface settlement trough volumes were also greater than the ground losses around the tunnel. In this case history, structural collapse of porous soils played an important role and must have been taken into account to predict correctly the settlement trough and profile. Numerical simulation has shown that settlement magnitudes due to structural collapse are strongly dependent on the soil stiffness reduction after collapse and the extent of the collapsible zone.

Jan 1, 1999

By H Parra, D Zenteno

Fragmentation modelling has been in use in the mining industry for a long time; however, there are still some aspects to tackle with regard to its use for strategic/planning and day-to-day purposes.On one hand, an important amount of resources are allocated to the task of calibrating and validating a good fragmentation model. Nonetheless, errors during the implementation stage introduce uncertainty into the prediction.On the other hand, it is common practice in the mining industry to use only discrete values to represent the fragmentation from blasting (k20, k50, k80), which provides a biased interpretation of the situation as, for instance, the best and worst possible cases are not taken into account. This is particularly critical when a continuous improvement philosophy has been adopted and modelling is used to either modify the drilling and blasting designs or plan ahead.It is well known that every site has particular conditions (rock mass, equipment, drilling and loading practices, among others) that often define unique trends in implementation. These trends can be captured using statistic and probabilistic techniques and then used as proxies for further analysis.This paper explores the potential of including implementation data in the form of probabilistic distributions into the Swebrec model to improve the performance of this engineering tool during the decision-making process.The fragmentation results of four designs were modelled using three different degrees of accuracy in the implementation for the burden, spacing and explosive column length.The data analysis showed that the probabilistic approach helps to achieve a broader perspective regarding the fragmentation that it is possible to obtain and the implications for the subsequent processes. The analysis also showed that the likelihood of producing similar fragmentation with different designs (involving different powder factors and costs associated) increases with the variability of the implementation.CITATION:Parra, H and Zenteno, D, 2015. Evaluating the inclusion of the implementation variability into fragmentation modelling, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 121–126 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By G Harbort, D Zoetbrood

"The Phu Kham copper-gold operation in the Laos People’s Democratic Republic (PDR) is owned and operated by Phu Bia Mining Limited. PanAust Limited holds a 90 per cent interest in Phu Bia Mining Limited, with the remaining ten per cent held by the Laos PDR Government.The original 12 Mt/a copper-gold concentrator at Phu Kham commenced production in April 2008. An incremental improvement program resulted in a number of circuit changes being incorporated by 2011, including conversion of conditioning tanks to flotation cells and the installation of a Jameson Cell cleaner scalper. In 2012 the Phu Kham Upgrade Project was commissioned to increase throughput to 18 Mt/a. In April, 2013 the Phu Kham Increased Recovery Project was commissioned to maximise performance by debottlenecking the plant IsaMill™ regrind and cleaning capacity.With the variable mineralogy of Phu Kham ore, control of the c concentrate regrind circuit is essential in terms of achieving effective liberation to maintain concentrator performance. On a routine basis laboratory regrind signature plot data is compared with daily surveys of the operational IsaMills™. More extensive surveys are also conducted to determine size distribution on a mineralogical basis and the effect of fine regrinding on pulp electrochemistry and flotation performance. This paper provides a review of the operating performance of the Phu Kham IsaMills™ with regard to power draw, feed and product size distribution, feed per cent solids, mineralogy and pulp electrochemistry. Operating performance is compared with the IsaMill™ signature plot test for predicting performance.Citation:Harbort, G, Zoetbrood, D and McNab, B, 2016. Operating Performance of the Phu Kham IsaMill™, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 39–50 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By T Suwa, S Ishida, J Xue, S Fuchida, H Shimada, Y Aoki, C Tokoro

Pyrite depression with prolonged pre-conditioning treatment in high salinity water has attracted much of researchers’ interest in recent years considering the increased utilisation of multiple stage flotation, closed water circuits, clay minerals, and sea water in flotation plants. In this study, the role of calcium (Ca)/magnesium (Mg) precipitates in stabilising the dissociative ferric hydroxy-xanthate (FHX), and its effect on modifying the balance of hydrophobic/hydrophilic species on the pyrite surface were primarily investigated. The total amount of extractable Fe-bearing species on pyrite concentrates and tailings after floatability test was quantitively determined using ethylenediaminetetraacetic acid (EDTA) extraction tests combined with inductively coupled plasma optical emission spectroscopy (ICP-OES). A more evident accumulation of extracted-Fe in pyrite concentrates rather than it in pyrite tailings was observed at both pH 9 and 10.5 when pyrite was pre-conditioned in Ca/Mg-bearing solutions for 360 min. Fourier transform infrared (FTIR) spectroscopy showed the main xanthate derivatives changed from di-xanthogen (1155 cm-1 ) to FHX (1167 cm-1 ) on the oxidised pyrite samples that were preconditioned in Ca/Mg-bearing solutions. Scanning electron microscopy-energy dispersive spectrometry (SEM-EDS) suggested the preferential accumulation of FHX upon secondary Ca/Mg-bearing precipitates as reflected by the higher Fe/S ratio together with the decrease of O element herein after xanthate conditioning. Although the hydrophilic secondary Ca/Mg/Fe-bearing minerals on the pyrite surface generally deteriorate pyrite’s floatability, the upper section of these secondary hydrophilic aggregates is partially covered by FHX alongside with further multilayer-adsorbed di-xanthogen. The precipitated Ca/Mg-bearing precipitates promotes the immobilisation of dissociated FHX derived from the reaction among iron oxyhydroxides and xanthate anions upon the localised secondary Ca/Mg/Fe-bearing minerals via acid–base complexation. Therefore, this phenomenon alleviates the hydrophilic modification of secondary Ca/Mg/Fe-bearing minerals to pyrite considering the immobilised FHX upon localised precipitates shows a slight hydrophobicity, and meanwhile, the upper FHX benefits the multilayer adsorption of di-xanthogen via the interaction among their inner hydrophobic alkyl chains.

Aug 24, 2022

By D L. Decker, G C. Miller, C Papelis

Arsenic, often associated with precious metals ore deposits, is a major contaminant released during large-scale gold mining. Because of the complex oxidation/reduction and sorption behaviour of As, prediction of the long-term mobility of As in pit lakes is uncertain. The behaviour of As in pit lakes is investigated in this paper by conducting a series of laboratory experiments where As is allowed to adsorb onto pit lakes sediments. Experiments were conducted over a range of pH with both As(III) and As(V) allowed to adsorb onto sediments collected from existing pit lakes found in the three main orebody types in Nevada, USA; porphyry copper, quartz-adularia gold, and Carlin Trend type gold deposits. Results from adsorption experiments show that As(V) and As(III) adsorption is strongly pH dependent with higher uptake at pH 5 and lower uptake at pH 9 for As(V) and higher uptake at pH 9 and lower uptake at pH 5 for As(III). This behaviour, as expected for oxyanions, has been described previously for agricultural soils, iron oxides, and Carlin Trend heap materials. Maximum adsorption of As(V) for the Carlin Trend type gold sediment was 3.0 g/kg at pH 5, 2.0 g/kg for the quartz-adularia sediment, and 0.9 g/kg for the copper porphyry sediment. Maximum adsorption of As(III) for Carlin Trend type gold sediment was 2.5 g/kg at pH 9, 2.2 g/kg for the quartz-adularia sediment, and 2.1 for the copper porphyry sediment. Adsorption isotherms are non-linear and show Freundlich isotherm behaviour. Variations in sorption between the different pit lake sediments under similar conditions can be explained by differences in the elemental composition of the sediment. Most rock forming elements from XRF analysis are similar in quantity except for Fe. The Fe content is highest in the Carlin Trend type gold deposit sediments and lowest in porphyry copper deposit sediments and is the third most abundant element in all three sediments. The Fe content of the sediments correlates well with the amount of As sorption seen in the laboratory experiments.

Jan 1, 2003

By C Moorhead, J Jones

A common problem in the mining industry is that company geologists can operate in relative isolation to the rest of the company (Jones and Moorhead, 2011). This may result in poor knowledge transfer and often priority conflicts with geology, operations and project departments. This problem is amplified by the acquisition of mineralogy capabilities and other metallurgical (met) test work undertaken by many companies in order to solve for complex orebody problems. Met data is often not located and viewed in 3D space so that geologists and engineers can create and work with geometallurgical (geomet) models (Bye, 2006). Visualisation of data in an interactive graphical 3D model provides a bridge enabling met professionals to collaborate with engineers and geologists to provide a common understanding of the relevance of geomet data.In recognition of this problem, Newcrest has undertaken an effective collaboration strategy to improve internal and external engagement through the use of large visualisation displays (Jones, 2009). The displays are underpinned by IT systems and information management practices that recognise the needs of underlying disciplines. Today it is generally understood within Newcrest that this is required to improve decision-making, deliver faster cycle times and improve governance.Collaboration in companies has been generally associated with the introduction of new IT functions (IBM, 2008). However, the science and engineering process that are used to structure modern IT-based collaboration systems and practices are now known to be simplistic compared to the long-standing practices associated with collaboration and knowledge management in disciplines such as geology and mining.CITATION:Jones, J and Moorhead, C, 2013. Geometallurgical communication as a distributed information system, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 133-138 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

By T Berryman, C Adams, L Griesel, C Buxton

The Kalgoorlie Consolidated Gold Mines (KCGM) schedule model is used for short- to medium-term planning and scheduling at the Fimiston Open Pit Mine (the Superpit). The model bridges the gap between grade control models, which are generated one to seven days prior to mining, and the annual Resource and Reserve model update that is used for budget and life-of-mine plans. The schedule model uses close-spaced grade control data (up to 20 000 m drilled each month) as well as resource definition drilling to estimate production volumes three to six months ahead of current mining. From this, a rolling 12 week mining and processing schedule is generated on a monthly basis. As the KCGM operation is mill and sulfur constrained, the schedule model needs to be an accurate predictor of ounces as well as tonnes, gold and sulfur grades. The process must also be time efficient in order to meet monthly planning and reporting deadlines. Due to the large amount of new data generated each month, model updates using conventional interpretation and estimation techniques have proven to be impractical and too time consuming. This paper will examine the evolution of the Superpit schedule model process over time, recent improvements and the effect of different model outcomes on short- and medium-term mine planning.CITATION:Griesel, L, Buxton, C, Adams, C and Berryman, T, 2014. The superpit schedule model – A time-efficient data-driven estimation for short- and medium-term planning, in Proceedings Ninth International Mining Geology Conference 2014 , pp 397–410 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By D Kilkenny

This paper discusses the use of a mechanised shaft sinking machine Herrenknecht Vertical Shaft Sinking Machine (VSM) – to conduct the 93 m presink for the Wira Hoisting Shaft at the Prominent Hill Mine in South Australia. This technology has been widely used in the global construction industry, however, this was the first time it had been used in Australia and the second time in a mining application. The non-entry shaft sinking system eliminates risks associated with a traditional manual method and allows all shaft construction operation to take place from surface. The geology in the upper 100 m at the Prominent Hill mine is conducive to mechanical excavation, with expected rock strengths below 130 MPa. This enabled an alternative shaft construction methodology to be considered. The Herrenknecht VSM system was selected due to its extensive work history and demonstrated performance in similar ground conditions. In collaboration with the operations and design team, the shaft collar and surface configuration were modified to suit the requirements of the VSM, additional equipment, and loading jacks that support the pre-cast lining. Dedicated concrete moulds were designed in Germany and built in Italy. The concrete segments were cast in Adelaide and road freighted to site. This paper outlines each stage of the presink – refurbishment, transportation, logistics, establishment, operation and demobilisation. Selecting this shaft presink excavation methodology, delivered through positive collaboration and communication despite some challenges, shows the benefit to the mining industry of applying new technology and innovation to improve safety and productivity.

Mar 29, 2023

By F Weir, B Estrada

The impact of seismic loading on open pit slope stability in Australia is often only considered where the slopes are located adjacent to tailings facilities or other major infrastructure. The debate regarding application of seismic loading in open pit design in Australia is usually founded on limited reporting on significant damage of open pit operations during earthquakes, the common perception that earthquakes do not occur in Australia or that they are unlikely to occur during the mine life of the mine. It is frequently overlooked that pit slopes that have withstood strong earthquakes in highly active seismic regions are often designed under strict seismic guidelines. This paper discusses the factors that impact earthquake performance of open mine slopes. These factors include topography, slope geometry, rock material and mass properties, water management and intrinsic pit design. Further, the paper presents insights into the characteristics of earthquake activity in Australia such as magnitude distribution, earthquake depths, areas prone of earthquake activity and general seismic hazard that are relevant to pit design. Guidelines are provided on the conditions and circumstances under which earthquake design in open pit mining should be considered. In addition, this paper provides recommendation on the applicable methods for assessment of the impacts of earthquake loading on pit slope stability.

Jun 22, 2022

Breakwater Resources Ltd is a Canadian base metals producer with Cu-Pb-Zn operations in Canada, Honduras, and Chile. Two of its operations contain economical gold levels which are recovered in both gravity and flotation concentrates. The gold payable terms in zinc concentrate are poor when compared to gold concentrates or copper concentrates and various flow sheets have been evaluated by Breakwater staff to maximise gold reporting in higher value products. The Myra Falls mine in British Columbia recovers coarse gold in the grinding circuit, part of which is upgraded and sold as a gravity-gold concentrate with the balance being directed to the copper concentrate. A sampling survey showed that there was potential gravity-recoverable gold in the copper regrind circuit. Installing a gravity concentrator in the copper regrind circuit increased the gold grade and recovery in the higher revenue copper concentrate and reduced the quantity reporting to the less well paid zinc concentrate. The El Toqui Mine in southern Chile has distinct high-and low-gold orebodies which are campaigned separately through the flotation plant. The high gold zone yields both a gravity concentrate and an unusual gold flotation concentrate. The gravity concentrate undergoes intensive cyanidation and electrowinning on-site to produce dore, while the fl otation concentrate is sold to gold producers. The zinc concentrate contains signifi cant gold values. The paper describes efforts over the past few years to improve gold returns at Breakwater's operations and highlights the different approaches dictated by the mineralogy of the gold occurrences at these two operations.

Aug 1, 2010