Search Documents

The Fraser Range is composed dominantly of basic pyroxene granulites derived from basalts, many of which appear to have been vesicular and*pillowed. Acidic and basic garnet-bearing granulites are important in the west, and acidic granulites and narrow anortho- site layers are dominant in some regions east of the Fraser Range. An extensive flat-lying olivine gabbro sheet cuts the granulites, and in places has been converted to spinel-bearing meta-gabbros and pyroxene granulites. The granulites of the Fraser Range (Proterozoic) are separated from the gneisses and schists of the Goldfields regions (Archaean) by the Fraser Fault, over which there is a large gravity anomaly (gradient 20 milligals per mile). Some of the problems associated with the concentration of Cu, Ni, etc. liberated from mineral lattices during metamorphism, and other principles of metal concentration in granulite terranes, are discussed. The recognition of vesicular and pillowed zones, even though highly metamorphosed, is of fundamental importance.

Jan 1, 1969

By S Bhandari

This paper is a step in the direction of developing a computer model of the near source dispersal of suspended particulate matter (SPM) in planetary boundary layer (PBL). Since Surface Mine blasting is done during daytime, study of daytime dispersion in convective boundary layer (CBL) is relevant to the mining engineers. The scope of this paper covers dispersal after the blast in any type of PBL ie stable, convective and neutral but only under weak wind condition. Mathematical analysis of the dispersion of vertical dust column has been carried out during weak wind conditions in a tropical meteorological environment. It is noted that dust concentration reaches its maximum value some distance away from the point of blast, immediately after the blast (t*=1) and thereafter rapidly decreases. After a short interval from the time of blast at t*=11 the dust concentration shows linear decrease in concentration with distance. Dust concentration also rapidly drops during the interval t*=1 to t*=11, thereafter, rate of drop is nearly the same at any distance from the point of blast.

Jan 1, 2001

Economic and technical reasons forced the mining industry all over the world to increase the unit size of mineral processing equipment. in large flotation cells, this development leads to problems in areas of air dispersion and keeping solids in suspension. Outokumpu, an operating mining company, designed and developed a mixing mechanism for large flotation cells at its own concentrators and also studied problems related to tank design. Ideal conditions for flotation can only be achieved if the flow pattern created by the mixing mechanism fits well into the tank configuration and the risk of short circuiting is minimized. In large deep flotation cells, four different zones can be found which improve the behaviour of large cells when compared to small cells. Selectivity is increased and in some cases final concentrate grades can be produced from the rougher cell. The largest units have also been used as final cleaners in some installations. When modernizing old plants by installing fewer larger flotation cells, immediate and substantial savings in power consumption are achieved. Additional power savings are made in pumping costs because of simpler circuit design and decreased circulating loads

Jan 1, 1978

A great range of contacting equipment is used in solvent extraction. However, a tower filled with a regular packing offers many advantages in the direct extraction from slurries. A study was made of the flow of a dense slurry through a packed tower in which the continuous phase was kerosene. The grid type packing, which was preferentially wetted by the slurry, had slats inclined at an angle of 30¦, to the horizontal. On the sur- face of the slats there were uniformly spaced longitudinal indentat- ions. These were of a height slightly less than the film thickness and divided the slurry discharging from the bottom of the slats into a number of uniform streams. When slurry entered the tower it was distributed by means of a troughs and weirs type of distributor. Because of the relatively high slurry velocities that occur at the entry region, it was necess- ary to have the distributor and the first two grids above the solvent level. The interface at the bottom of the tower was located at the mid-point of the bottom grid, so that the slurry entered the interface as a continuous film across the full width of the slats. Using the above system, stable flow with low entrainment was achieved at slurry flow rates of 3.4 mis/cm/sec. This would be equivalent to a flow rate of 177 gallons per minute through a tower of cross-section 4 ft 4 in. by 4 ft 10 in., or 1200 tons per day of solids of specific gravity 2.6 when the pulp density was 65 per cent. Previous tests indicated that a total tower height of about 30 ft would be required for a recovery of better than 99 per cent.

Jan 1, 1969

By Z-Y Pi, B Zhang, S Wen

"The paper introduces the structure and work processes of outside auger hollow claw tipped mechanical sampler for coal. Twenty sets of claw tipped sampler performance tests show that: The design of inner hollow cylinder-type (?180 mm) can ensure to take a coal sample with nominal top size of 60 mm. Built-in self-cleaning piston pusher ensures no adherence and blocking of the sample. The operation practices show that the mechanical sampler can operate in order for taking coal sample with up to 16 per cent of total moisture. Claw closing design can avoid sample leaking or spilling during the claw lifting and ensure the integrity of primary increment. Ultrasonic positioning device makes the sampler capture the materials no less than 10 cm from the bottom of the wagons, basically meeting the requirement taking full depth of the sample. The precision and bias test indicates that the moisture and ash have no relative bias under the sampling process; the sampling precision is in accordance with the requirement in IS013909.At present, the spiral mechanical sampler is widely used for coal sampling but there are many limitations during application, for example: It is difficult to capture a large size sample, so the size range of a coal sample taken is limited. There is easy adhering or blocking for high moisture coal, which will result in the mixture of different increments, wear of sampler and the difficulties for cleaning and maintenance of sampler. It is difficult to capture the coal sample at lower than 30 cm from the bottom of the wagons, in order to avoid damage of the vehicle. It is possible for coal sample loss and spilling during the sampler lifting, due to the unsealed sampler.For the outside auger hollow claw tipped mechanical sampler designed for solving the above problems, the opening distance of the claw is the opening size of the sampler and makes the size range of the coal sample to be taken wide. During sampling, the two pieces of claws open and the sampler rotates vertically downward to capture an adequate coal sample after reaching the specific point. Then the two pieces of claws close tight automatically to ensure there is no coal leaking or spilling. The inner pusher of the sampler will prevent from the adherence and blocking of the coal sample effectively.CITATION:Zhang, B, Pi, Z-Y and Wen, S, 2012. Outside auger hollow claw tipped mechanical sampler for coal, in Proceedings Sampling 2012, pp 41-44 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 21, 2012

By L Lorenzen, H Muller

"Every year a large number of projects are evaluated by small listed and unlisted mining companies that are hoping to find the ideal project, which will catapult them from a mining junior status to that of a mid-tier mining company. Usually this includes finding the æidealÆ or ærightÆ orebody and then developing a process which will allow cost-effective recovery of the valuable metals and the production of a saleable product. These dreams are seldom realised and there are a number of good and obvious reasons for this. Issues that are generally high up on the agenda for the smaller companies are: cost of developing a project before the feasibility study stage finding a suitable, or optimum processing technology financing of the project dealing with risk.The most expensive part of the development process for the small miner is often the exploration side of the business and finding the æidealÆ orebody. However, finding the right orebody will not be discussed in this paper. The æidealÆ orebody does not necessarily solve the problems of the mining junior, as much of the uncertainty lies in the process required to recover and produce the final metal product. Once a mineralised deposit has been identified and the grade at least reasonably qualified, the development of a suitable process becomes the driver to convert the deposit into an orebody. This paper proposes that a small exploration company has a very limited opportunity to succeed if it does not do sufficient homework before it identifies the æidealÆ orebody. The risk profile for the small mining company, by its very nature, has to be different to that of a major company and as a result the opportunities often lie in managing different and often new process options, which may be the key to bring such projects on line successfully.CITATION:Muller, H and Lorenzen, L, 2012. Project selection and process development for mining juniors, in Proceedings Project Evaluation 2012, pp 149-158 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

May 24, 2012

By I Elias, E Moya, S Chaffer

This paper is based on a case study from a mine site that operates two gyratory primary crushers. These crushers were encountering problems, which included inconsistent P80, reduced liner life tonnage and, on some occasions, catastrophic failure of the liners.As part of an evaluation process, both crushers were ‘mapped’ using a technology for condition monitoring and modelling of the crusher’s wear components. The technology provides comprehensive coverage of the crusher’s concaves and mantle at 100 mm intervals. It also automatically assesses wear rate between inspections and determines the highest wear areas. Outcomes include projected optimum reline dates at target replacement thicknesses, the identification of asymmetrical wear patterns, and the accurate measurement of open and closed (OSS/CSS) side settings.A comprehensive study was performed to optimise the performance of both these crushers at site. Over a period of seven liner service lives, the strategies to improved performance included liner analysis (concaves and mantle profile analysis), tonnes per day (t/d) and tonnes per hour (t/h) analysis, mantle reutilisation, detection and control of loose concaves, and detection and control of uneven wear and hot spots.These strategies resulted in the improved mechanical and operational performance of both crushers through concave and mantle redesign, OSS/CSS control, accurate wear forecasting plus other initiatives.As a result of these initiatives, the site now experiences benefits which include consistent product size, increased tonnes per hour (t/h) for both crushers and the liner life tonnage has doubled. Additionally, further benefits include less downtime for crusher liner maintenance and the reduced cost of inventories by mantle reutilisation.CITATION:Elias, I, Chaffer, S and Moya, E, 2015. Improvements in service life and cost reduction for gyratory primary crushers through mantle and concaves optimisation – a case study, in Proceedings Iron Ore 2015, pp 115–128 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

Declines for both access and rock haulage are replacing shafts for mining relatively shallow deposits of down to 1000 m below surface. Where the orebody does not outcrop and where surface access may be restricted, it is often necessary to drive long dead end headings before a connection can be made back to surface and a ventilation circuit created. In hot tropical areas and where large diesel powered equipment is used for mining, heat may also be a problem at these relatively shallow depths. The normal design criteria based on statutory limits and good practice used to evaluate ventilation and cooling requirements in terms of air velocity, dust, gases, diesel exhaust dilution, re-entry after blasting and heat stress are described in this paper. These are then used to design and cost alternative auxiliary ventilation systems that include leakage based on general fan performance curves and typical duct systems. The implications of the current European Community recommendations regarding nitrous fumes are also briefly considered. The actual problem relates to a 2100 m long decline that may have to be extended to 3000 m long without a connection to surface or through ventilation and is located in a hot tropical area where the surface wet bulb temperatures may exceed 25¦C for more than a third of the summer period. Once the preliminary ventilation design is completed, the auxiliary ventilation system can be modelled and simulations undertaken that incorporate heat and moisture transfer routines with the objective of determining the cooling load and amount of refrigeration required. Cognisance is taken of cyclic diesel operations and the thermal flywheel effect of the surrounding rock on the wet and dry bulb temperatures resulting from these operations.A suitable modular cooling system located at the portal is described and optimised with capital and operating costs of both the ventilation and cooling systems provided.

Jan 1, 2005

I am honoured and very pleased to have been given the opportunity this evening to say a few words of thanks not only on behalf of all the guests but especially for the delegates and accompanying persons attending the 13th Congress of the Council of Mining and Metallurgical Institutions. Firstly, I would like to congratulate Sir Hamilton Whyte,KCMG for his most interesting address. In his far ranging talk, when he showed knowledge of widely diverse subjects, I had a brief fear that he was going to be talking about the details of support methods in deep level mines, or how to avoid flotation problems in multi-metal mines. Although he did not go that far, he touched on subjects which have arisen this week - long term planning and secure supply of minerals at acceptable prices. The dire predictions of the Club of Rome have been debunked with a far more elastic supply of minerals having been proved. Combined with the importance of a falling birthrate in some parts of the world, this will lead to many changes in the future, when hopefully governments will take the long term view rather than look at the next budget or the next election. Maybe some of them are not too lazy to do this for all of us. However as a fellow Ukranian, I feel that he might have been called something different if he had been in Australia. Sir Hamilton, thank you for your talk. Once upon a time - and this is not a fairy story - there was a cobbler who had two sons; one very bright who became a professor of mathematics; the other, dim, who became a millionaire shoemaker. Asked for the secret of his success, the millionaire attributed it to a vital piece of economics which his father had imparted, "Be content with small margins on a large turnover." "So", said the millionaire, "I make my shoes for $2 a pair and sell them for $5. I am very happy with the three per cent profit."

Jan 1, 1986

By J Kok

"In some underground mines it has been observed that the primary focus during feasibility studies is to determine the best way to mine the defined orebody. Some studies have been conducted without sufficient consideration of the ventilation and cooling requirements or the risk from exposure to associated airborne pollutants caused by the mining operations.Following the hierarchy of control to manage risk, numerous problems of the ventilation systems in some underground mines could have been avoided if sufficient consideration was given to the ventilation requirements to manage heat, airborne pollutants and leakage during the feasibility study phase. If the constraints and hazards were well defined and understood at the time of the study, efforts could have been made to eliminate or substitute the hazards to decrease the risk. Some of these problems include but are not limited to: primary fan locations heat loads diesel exhaust ventilation design based on the production requirement fire/emergency response strategies.This paper highlights areas in the ventilation discipline that are sometimes overlooked during feasibility studies. It will also highlight the importance of the Ventilation Specialist during these studies. Experience and knowledge of best ventilation practices must be applied in feasibility studies.As a result of adequate consideration to all ventilation aspects in the feasibility study phase, risks will become lower in terms of health, safety, production loss and equipment downtime caused by heat.CITATION:Kok, J, 2014. Feasibility studies – what should be considered in terms of ventilation, in Proceedings 12th AusIMM Underground Operators’ Conference 2014, pp 197–204 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 24, 2014

By E A. Gunn, J Zhou

In this paper a project to develop a joint optimisation/simulation model for production planning in a mine-mill complex is presented. The system involves a mill receiving ore from a number of different locations, each with a unique mineral composition. The mill consists of several crushing and grinding circuits that function in series and parallel. Scheduling the flow of materials through the mill is complex due to constraints on throughput imposed by the millÆs design, the length of time material can be stockpiled on the surface, varying input mineral composition, and throughput targets for a range of output products.An optimisation model is used to create a set of campaigns (ore feed rates) over a given planning horizon under the assumption of deterministic mill throughput. A simulation model is used to evaluate the production plan under assumptions of stochastic machine failure and operational losses created by the need to cycle between input feeds. Campaign scheduling has two important implications for the simulation. First, during any campaign, multiple ore types may need to flow through the mill. However, the mill must be controlled to ensure that only one type of ore can be in a crusher, a grinder or a storage bin at any point in time. Second, as the mill switches from one campaign to another, the set of ores being processed may differ. Thus, the flow of ore through the equipment during a campaign changeover must be controlled to ensure that one or more of the ores from the current campaign can be completely eliminated before the ores from the new campaign are introduced.The simulation architecture employed for this project is Visual Basic for Applications (VBA) combined with MS-Excel as a user interface. A fixed step discrete event orientation is assumed as the simulation framework. A set of model constructs was built for the project with a specific Canadian milling operation in mind, but was designed to be representative of a broad class of milling operations. The constructs are implemented as class objects within the VBA structure, each with a number of properties and methods. The collection of VBA objects forms a composable modelling toolkit. These objects can be linked together by users, via MS-Excel, to represent a broad range of milling operations.

Sep 26, 2011

By A Sadri, S Smith

In the metal and mineral industry, different empirical techniques are used to estimate the remaining thickness of the lining within an operating furnace. The disadvantage and costly factor when using these methods is that production needs to be halted. Hatch has developed an accurate and reliable technique based on stress wave propagation principles to determine the condition of the remaining lining whilst the furnace remains online and operational.The technique involves test data collected and compiled to generate 3D imagery used to assist operators and maintenance planning personnel with valuable information showing areas of metal penetration in the lining, remaining lining thickness, exact location of voids, cracks, poor contacts and deterioration due to chemical attack. In this paper, the principals of the AU-E technique will be explained both theoretically and practically. In addition, the use of ultrasound technology for determining the condition of copper cooling elements will be briefly addressed.

Jan 1, 2006

By K T. Mandisodza, T J. Cartledge

The principal objective of Geotechnical Engineers supporting operating mines is to provide safe working conditions and ensure that pit designs are geotechnically optimised to site conditions and pre-defined stability requirements. Pit slope designs are delivered in advance of pit excavations. Making changes to these designs is usually slow to enact and involves a layered sign-off before implementation, leading to unwanted delays in their adoption and subsequently increased production pressures. When unexpected ground conditions are encountered during the mining process, or short-term mining schedule requirements demand it, changes to these designs may not be easily feasible in certain situations. It is when these scenarios arise that Geotechnical Engineers need to be proactive and consider unconventional options to deliver safe operating conditions while satisfying short-term requirements to the mine schedule. Essentially, the geotechnical short-term strategic designs double-pronged approach supports the mine schedule while providing safe conditions and minimising geotechnical risks for people and equipment. Common short-term strategic geotechnical designs include; slope buttressing, over-steepening cut slopes to increase reserve recovery through unplanned or emergency cutbacks, and accepting risk threat and operating under unstable slopes. When implementing strategic design options, the Geotechnical Engineer must consider the broader implications for such designs. They must think of the plan’s long-term effects on the mine schedule and pit wall stability. Initiating aggressive designs to recover additional reserves to satisfy a short-term scheduling demand could result in-pit wall instability or suboptimal pit layout. Before and during the implementation phase, the Geotechnical Engineer must communicate and engage with relevant stakeholders to ensure that the plan is executed accordingly and geotechnical risks are effectively managed. Proactiveness to ground response and implementation of risk management strategies will improve safety performance and optimise mining schedules.

Jun 22, 2022

By L J. Strachan, O J. Hawes, S W. Crossen, R C. Roberts

The Albany Conglomerate is a widespread geological unit found in northern areas of Auckland, New Zealand. It has previously been described as part of the early Miocene Waitemata Group which underlies most of Auckland. Much of the Waitemata Group comprises weak interbedded sandstones and mudstones, but also includes conspicuous conglomeratic units such as the Albany Conglomerate. The Albany Conglomerate comprises a well-cemented mixture of hard pebbles, cobbles and boulders of igneous and metamorphic derivation in lenticular beds. A number of tunnelling projects are planned for the near future in Auckland. Recent experience has shown that the variable features associated with the Albany Conglomerate can make selecting appropriate construction methods very challenging. This paper explores the engineering geological and sedimentological features of the Albany Conglomerate with respect to other conglomerates within the Waitemata Group and the potential implications on tunnelling projects in Auckland. Consideration is given to the extent of proposed geotechnical investigations and the production of geotechnical baseline reports.CITATION:Roberts, R C, Hawes, O J, Crossen, S W and Strachan, L J, 2014. Underground construction challenges associated with the Albany Conglomerate in Auckland, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 195–202 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

The Olympic Dam mining operation is some 520 kilometres NNW of Adelaide on the Roxby Downs Pastoral lease. The deposit containing copper, uranium, gold and silver was discovered in 1975 by Western Mining Corporation (WMC). A joint venture was formed in mid-1979 between WMC (51 per cent) and British Petroleum (BP, 49 per cent) for the development and exploitation of the deposit. WMC assumed 100 per cent ownership after acquiring BP's share in early-1993. Ore is won from a highly mechanised underground mining operation and processed to refined products. Current annual output from the mining of 3.0 Mt of ore is approximately 83 500 t of refined copper, 1400 t of uranium oxide, 750 kg of gold and 12 000 kg of silver. Conventional long hole, open stoping techniques are used to extract the production ore. Since stope production began in April 1988, full surveys and appraisals of stopes have been carried out to evaluate the integrity of the design and blasting techniques. This evaluation included the determination of the degree of dilution or non break that had occurred. Performance information also made it possible to re-design any adjacent stopes to retrieve remaining ore and conversely, avoid the chances of targeting backfilled material in the future. Performing stope surveys proved not only to be a time-consuming process but one fraught with access and line-of-sight problems. Occasionally it was not possible to obtain any stope survey data, and as was often the case with the mine pass system, rarely. In 1992 the sudden failure of the pillar between the fine ore and mullock passes and the subsequent delays to production, emphasised the need to effectively monitor pass wear. Initial information regarding the development of the Cavity Measurement System (CMS) prototype (Figure 1) indicated that it had the potential to solve these problems by the introduction of a remote scanning device into a cavity. Following a great deal of investigation, Olympic Dam Operations purchased the first CMS in Australia. This paper discusses its application for all underground void surveys and the procedures developed to manage both field and office requirements.

Jan 1, 1995

By P McCarthy

The relatively new field of geo-metallurgy promises to improve the predictability of mill feed quality and enhance processing outcomes. However, it is subject to the same limitations as the prediction of grade using geostatistics and has additional limitations due to the spatial distribution of the variations being measured and the sample sizes required. Schedules based on geo-metallurgical models will, in turn, be subject to variations arising from geological control and practical mining constraints.This paper discusses the key drivers of variations in mill feed quality and quantity from a mining perspective. It concludes that geo-metallurgical modelling addresses only one aspect of the problem. A case study is provided to illustrate poor predictability of metallurgical performance even with very detailed geological data.

Aug 8, 2011

A study of the bacterial oxidation of naturally occurring high-purity sulphide minerals (FeS2, Fel_xS, CuFeS2, Cu2S) has been conducted using a mesophilic strain of T. 6ejtAooLcdcth4. As well as metal analyses and solution pH, partitioning of sulphide sulphur into elemental sulphur and sulphate ion has been monitored. Partially oxidised sulphide substrates have been characterised at regular time intervals by X-ray diffraction methods and extra-cellular organic compounds reporting into leach solution have been identified by'thin layer chromatography. The results indicate that the S¦/SO4 2 partitioning of the sulphide substrates is independent of cell inoculum size and initial pulp density and varies with solution pH, Eh, leaching time and mineralogical properties of the individual sulphide minerals. The signifi- cance of results for applications in selective flotation, coal desulphurisation and agglomera- tion has been outlined.

Jan 1, 1984

By I Gipps

A vision of what the future mine involves all aspects of mining, ie orebody access, ore stoping, material transport, processing and waste material disposal. This paper examines one aspect of the future mine: rock extraction, stoping, automated for remote operation, high productivity and low cost. Concepts for the future require a re-think of the mining process and ROES® re-examines how bulk stoping of ore can be undertaken and how this should be redesigned to accommodate the possibilities that exists with remote control and automated operations.ROES® is a new mining system for underground mines and quarries utilising a shaft located close to or within the stope for the ore breakage process. The system is designed to exclude personnel from contact with production drilling, explosive placement and detonation so all of these tasks are remotely controlled or automated. Survey of the shaft, stope back and broken rock within the stope will occur, following each blast, by remote control or automated techniques. The survey will include excavation geometry, rock fragmentation, geotechnical characterisation and estimation of ore grade. Blastholes will be surveyed before placement of explosives and, with the survey data, the optimal explosive placement and blast timing will be determined with the best available information.ROES® is designed for application in open stoping or sublevel caving in disseminated, geologically defined, thick tabular or narrow vein ore bodies. Technologies developed for ROES® will also have potential applications to caving operations, reducing the risk of frozen ore and poor fragmentation. In a typical sublevel open stope application, ROES® will reduce the stope associated development by half and will allow ore to be brought on-stream sooner and at lower cost. Other savings will flow with the centralisation of mining activities and operational data, reduction in mining fleet, reduction in ventilation requirements, improved occupational safety and reduced mine complexity.

Nov 22, 2011

The disadvantages of the present zinc producing methods, RLE and ISP, are high energy consumption and environmental problems. Therefore, efforts have been directed in Outokumpu Zinc towards the development of alternate routes. One interesting pyrometallurgical process to produce zinc is to inject zinc calcine together with a solid reductant into molten iron, saturated with carbon. This process has been studied by thermodynamic calculations, laboratory tests and mini-pilot test runs at Outokumpu Research Oy, Pori, Finland. The results of these tests are presented and discussed in this paper. The mini-pilot tests demonstrated that over 97 per cent evaporation of the zinc was possible using a reactive coal dust as the reducing agent. The recovery of zinc in the metal phase was at best 88 per cent of input zinc, but only part reported in molten lead in the splash condenser. The final metallic zinc contained at best 98 per cent Zn, the main impurities being dissolved lead and coal carried along with the flue dusts.

Jan 1, 1993

Vertical flow systems (SAPS, vertical flow wetlands) are increasingly used for passive treatment of mine drainage that is net acid. Data on 30 systems in eastern US show that well designed systems typically add about 40 g/d/m2 of alkalinity to influent net acid water. If they are designed with a conservative loading rate of 25 g/d/m2 and carefully constructed, they produce net alkaline water. Alkalinity added depends on influent acidity, Fe, pH, and retention time, and ranges widely, from 7 to 484 mg/L, so this is not a useful design criterion. Some waters may benefit from retention times longer than the conventional 12 - 16 hours, but the design must be partly based on cost-benefit considerations. Systems with fine limestone added to the compost layer perform better than average, perhaps to an alkalinity generation rate of 80 g/m2/d. A variety of problems are noted in the 30 systems and others reported in the literature. Systems with high influent Fe (> ~75 mg/L, varying with pH) tend to gradually decrease in flow rate because of precipitation and settling of Fe hydroxides on top of the compost layer. Some high-Fe systems precipitate Fe in the limestone layer, suggesting inadequate compost thickness, or short-circuiting through thin spots. Systems with Al exceeding about 10 mg/L tend to plug because of Al hydroxide precipitation in the limestone layer. Flushing only removes a small part of this precipitate, but can extend life. Some systems are ineffective because of failure of the inflow system. Some systems are uneconomic because they are oversized. A continuing program of inspection and maintenance is necessary for long-term performance.

Jan 1, 2003