Search Documents

By V Mutton, L Potts, D Joyce

This paper describes the method of extracting sill pillars within the underground operation from under unconsolidated mullock fill at the Cracow Gold Mine. This pillar recovery method was initially successfully used to recover sill pillars at Crusader Mine, Western Australia in 2001. Globally significant resources have been sterilised due to the placement of loose rock fill above crown pillars and within adjacent stopes. The method described here offers significant opportunities to increase recovery of sill pillar recoveries.The royal orebody sill pillars at Cracow Gold Mine form a significant resource. Extraction of these pillars needed to be undertaken with minimal ore dilution and maximum ore recovery. The application that was selected to consolidate the loose mullock fill above each pillar used an injection grouting process (Minova FB200).Cracow Gold Mine mining method is bottom up bench mining. The pillars were left within the orebody to allow for stoping to commence whilst the decline was being developed. Due to the remainder of the orebody being extracted the only access to consolidate the backfill was from the sill pillar extraction level. Numerous problems were encountered and overcome from product selection and trial, system of injection to extraction.This pillar recovery process achieved a 95 per cent recovery of the sill pillar compared with an estimated 60 per cent typical for other mining options.CITATION:Potts, L, Mutton, V and Joyce, D, 2012. Pillar recovery at Cracow gold mine using grouted consolidated mullock, in Proceedings Narrow Vein Mining 2012 , pp 179-184 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 26, 2012

By D J. Brake

Most mine ventilation engineers are involved in ventilation planning and design in some capacity. Ventilation modelling software used by a competent experienced ventilation engineer is extremely useful in developing good ventilation designs by allowing assessment of a wide range of potential options. Unfortunately, ventilation modelling undertaken by persons who do not have sufficient experience or knowledge usually results in a façade that covers up a fundamentally unsatisfactory design. Ventilation models are produced for a wide variety of purposes including: fault-finding of a problem area in a mine and options analysis for resolution of such problems; a complete review or optimisation exercise of an entire mine’s ventilation system; or a much longer life-of-mine type of study. Models can be intended as the basis for studies with diverse purposes such as primary shaft or airway sizing, primary fan specification, examining re-entry times after blasting, resolving leakage or recirculation, or investigating the impact of fires or underground climate or cooling requirements. The concepts of ‘materiality’ and ‘fitness for purpose’ are essential to developing or using a ventilation model and serious mistakes have been made in wrongly using a ventilation model for purposes for which it was never intended, often because it is simply the most recent model on the mine site. Mistakes at this level often translate into faulty ventilation strategies and inefficient or ineffective use of scarce capital for ventilation projects. Validating a ventilation model is a time-consuming and expensive process and not every model must (or even should) be fully validated to meet the objectives at that time. This paper discusses the application of quality assurance in ventilation planning with particular respect to the ‘basis of design’ (BOD) as well as the standards for validating a ventilation model. It also provides a recommended way of dealing with non-conformances in measured versus modelled values of critical parameters in the model.CITATION:Brake, D J, 2015. Quality assurance standards for mine ventilation models and ventilation planning, in Proceedings The Australian Mine Ventilation Conference, pp 221–228 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By A Tsang, D La Rosa, L Julian, W Hunt, R Pratama

Mineral extraction is facing the twin challenges of finite resources and increasing environmental and economic costs. Society’s growth is matched by an increase in demand for the earth’s resources. It is incumbent on us as contemporary mining professionals to promote and facilitate ethical and efficient practices. Technological developments have and will continue to allow a decrease in viable cut-off grades, creating new economic opportunities from deposits that were previously uneconomic. Mining low-grade deposits however, even with perfect recoveries, will have a significant environmental cost for the metal won. The greatest opportunity to increase metal with the least environmental cost is to increase the metal yield from existing mines. The determination of mining polygons is a critical juncture where rock is typically subjected to the binary grading of either ore or waste. This is undertaken using a number of factors, such as the mining equipment being used and the recovery in the processing plant. Traditionally, mining polygons were generated on the in situ grade control model. This ignores the complex differential blast dynamics that occur during blasting. Two opportunities exist to improve metal yields: optimise the blast design to achieve the post-blast muck pile that will support the greatest outcome; and generate optimised polygons on the post-blast muck pile. A data set from a Canadian Gold deposit is used to demonstrate the potential benefit of iterative blast movement modelling and grade control polygon optimisation on metal yield. The impact of blasting on the total recoverable metal is presented, highlighting blast design as a critical process in the mining value chain.

Sep 1, 2024

By Hatherly P, Holt GE, McNally G

The current methodology for delineating and subsequently evaluating coal reserves is based on the use of vertical drill holes and surface based geophysics/geology. These techniques have three major problems, these being respectively:-a) Vertical drill holes can only provide a small sample of the coal seam and stratigraphy. Therefore the planar variation in coal reserve and environment parameters can only be approximated.b) Although surface based geophysics has had its fair share of success in recent years, there are still environments which have masked the finding of major structures.c) Access to drill sites is difficult at some locations due to mountaineous terrain, standing water and environmental impact.

Jan 1, 1985

By Robbilliard K. R, Floyd J. M

The problems facing the metallurgical industry from the viewpoint of the range of unacceptable residues, flue dusts and slags currently produced from the electrolytic zinc process, electric arc furnace scrap treatment, and blast furnace operation in lead smelting and the Imperial Smelting Process (ISP) are addressed. The application of the Ausmelt technology is discussed and analysed for the pyrometallurgical treatment of zinc plant residues, steel plant flue dusts and lead blast furnace and ISP slags, as well as the more complex issue of smelter modernisation to avoid production of zinc plant residues in the future. Processes developed from pilot work are described and indications of the economics of treatment of electrolytic zinc plant neutral residue and jarosite are given.

Jan 1, 1993

By J-T Zhu, Q-Y Tu, S-L Kong, L Wang, Y-P Cheng, H-Y Liu, Q-L Yang

China is the largest coal-producing country in the world, while the geological conditions of deep coal mining are extremely complicated with high ground stress, high gas pressure and low permeability, which results in the difficulty of gas drainage and aggravation of gas explosion and coal and gas outburst disasters. Co-extraction of coal and gas is an effective method to eliminate coalmine gas disasters and realise the safe exploitation of coal and efficient gas drainage at the same time. This concept is widely accepted by the main coal-producing countries around the world, while the concrete definition of co-extraction is vague and not unified, and there is little accurate theoretical support for co-extraction of coal and gas, which makes it hard to determine efficient gas drainage methods correspondingly according to the features of coal seams in a comprehensive and systematic way. Based on theoretical analysis, laboratory test and field observations, basic thoughts and specific definition of co-extraction of coal and gas were put forward after analysing the occurrence characteristics of coal seams in China. We obtained the mechanism of mining-enhanced permeability and established the corresponding theoretical model, which is the process of fracture network formation through opening recovery of the original fractures and new fractures produced by unloading damage. Based on the core idea of ‘mining-enhanced permeability’, engineering approaches of ‘unloading by boreholes drilling’ for the single coal seam and ‘unloading by protective seam mining’ for the coal seam group were proposed to realise safe and efficient co-extraction of coal and gas. Meanwhile, combined with engineering practice, we put forward the construction principle of coal exploitation and gas drainage system in different coal seam occurrence conditions. The above methods were applied successfully in the Tunlan coalmine in Shanxi Province and the Panyi coalmine in Anhui Province, which had established the ‘underground-surface united’ spatial gas drainage modes, and could ensure safe and efficient co-extraction of coal and gas in the outburst coalmines.CITATION:Cheng, Y-P, Wang, L, Liu, H-Y, Kong, S-L, Yang, Q-L, Zhu, J-T and Tu, Q-Y, 2015. Theory of safe and efficient co-extraction of coal and gas and its applications, in Proceedings The Australian Mine Ventilation Conference, pp 79–92 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By D Kilkenny, D Nardini, P Kline

This paper is a case study highlighting learnings and success in two areas challenging underground miners: change management and collaboration. It examines the implementation process of a new automated loading system in the bulk stoping area of Telfer Mine in Western Australia, controlling multiple load haul dump machines. Here, the new technology has brought together different functions and different companies to deliver a well performing automation system in a changing and challenging mining environment. The introduction of a new and different technology on site has driven collaboration between all stakeholders to break down the traditional barriers to achieve the sustained performance required. Historically, different teams have operated within silos and not always aligned to deliver a ‘best for project’ solution. Technical teams focus on the mine design, maintenance teams focus on reliability and operations execute the plan. Mining contractors focus on productivity and cost. Manufacturers focus on supply of goods and service. Optimising each silo individually is not guaranteed to provide an optimal mining solution. Involving elements from each team as seen at Telfer, has resulted in an optimal mining solution for the automated loading system. A change of focus from the technical teams to include automation parameters in the mine design; operability and maintainability built into the system design allowing for collective ownership and responsibility resulting in a more resilient solution. The implementation of the new technology was not only a technical change but more importantly, successful management of change. Elements of successful change management such as communication, vision, leadership and planning, are essential to harness a trusting site culture which is responsive to new technology. Learnings and challenges from this change process will also be discussed with the intent to improve the success rate and timelines of technology implementations in the future.

Mar 15, 2021

By O Arafat, R E. McIvor, K M. Bartholomew

It is well known in the industry that good classification system performance is vital to efficient ball mill circuit performance. But what is meant by good classification system performance, and how is it achieved? Unfortunately, the perceived complexity of classification systems, and the day-to-day time demands placed on the practicing metallurgist, all too often put the low-hanging fruit of classification system optimisation in the ‘I’ll do it later’ basket. Additionally, lingering confusion about basics such as the relationship between circulating load ratio and ball mill circuit performance makes the optimisation objective seem nebulous to both plant metallurgist and designer.Some of this confusion can be eliminated by taking a step back from the overwhelming detail of sharpness of separation curves, circulating load ratios, cyclone feed pressures, vortex and apex sizes etc, and focusing on the purpose or function of the classification system – to apply mill power to particles that need further size reduction! The classification system efficiency (CSE) metric captures how well the classification system is performing its function with two quick and easy size distribution analyses.Once CSE is understood and implemented as the optimisation criteria, well-tested methods for improving CSE can be implemented and quickly measured at plant scale to give confidence that the right change was made.This paper will describe CSE and how it is measured in practice. Next, a guide for improving CSE through manipulation of design and operating variables in the classification system will be provided. Examples and case studies will illustrate the gains in ball mill circuit efficiency that can be achieved by maximising CSE.CITATION:Bartholomew, K M, McIvor, R E and Arafat, O, 2018. A guide to maximising ball mill circuit classification system efficiency (CSE), for operators and equipment designers, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 553–558 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By Y Li, Z Fu, D J. Williams, E Topal

Mine waste rock is unavoidable in the recovery of ore by open pit mining methods. Effective management of waste rock movement covers the removal and placement of the waste rock, generally in a surface dump in the most cost-effective way while satisfying the long-term environmental expectations. Since the 1960s, there has been significant research carried out into planning of ore movement from open pit mines such that the overall net present value (NPV) of the project can be maximised. Currently, several software packages are available to achieve this task as a common practice within the mining industry. However, planning of mine waste rock movement is still achieved manually, as the available software does not consider optimal waste rock movement and dump design. This paper describes a tool to optimise waste rock placement, which minimises the haulage cost while creating environmentally friendly waste rock dumps through selective placement and encapsulation of the reactive waste rock in the dump. The embedded methodology in this tool has been developed based on the mixed integer programming (MIP) modelling technique to optimise the waste rock movement. The methodology provides an easily-manipulated and fully-automatic tool for professionals to complete waste rock dump scheduling in four main steps: data input, model construction, model computation and solution retrieval. The application of the new tool into a real case project in this paper shows that it can determine economically and environmentally optimised waste rock dump schedules in an acceptable time frame.CITATION:Fu, Z, Li, Y, Topal, E and Williams, D J, 2015. A new tool for optimisation of mine waste management in potential acid forming conditions, in Proceedings Tailings and Mine Waste Management for the 21st Century, pp 333–342 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By Q Wang

Net present value (NPV) has been the main criterion in mining project evaluation and production plan optimisation. It is a common practice in NPV calculations to take into account only the tangible cost items in the corporate accounting system. The costs incurred due to damage to the local ecosystem and environment are left out and treated as externalities. Such practice on the one hand underestimates the total cost of a mining operation and, on the other hand, ignores the difference in ecological/environmental impacts between different mine plan alternatives. This paper attempts to measure the ecological costs of mining and to incorporate such costs into the evaluation scheme in mining project evaluation and mine planning. The ecological costs of mining are estimated based on the areas and types of land (eg forest land, grazing land, crop land) damaged by mining activities and the carbon emission from fossil fuel consumption. For the land areas (and their associated ecosystems) directly damaged by mining activities, the ecological costs are measured by the prevention and restoration costs, the lost values of eco-services of the damaged land, including bio-product production, soil erosion control, water run-off control, oxygen release, air pollutant absorption and formation of soil nutrients. The ecological cost of carbon emission from the energy consumption of a mining operation is measured by the cost of cultivating the equivalent forest land required to uptake the emitted carbon. A case study on a large-scale open pit mining project is presented to demonstrate the influence of ecological costs on the mine planning outcome.

Sep 26, 2011

By A H. Bagherieh, S Mesroghli, H Jorjani, S Chehreh Chelgani

The rare earth elements (REEs) assay and recovery in leaching processes is being determined using expensive analytical methods, ICP-AES, and ICP-MS. This paper presents a neural network model to predict the effects of operational variables on the lanthanum, cerium, yttrium, neodymium recovery in the leaching of apatite concentrate. The effects of leaching times: ten to 40 min, pulp densities: 30 to 50 per cent, acid concentrations: 20 to 60 per cent and agitation rates: 100 to 200 rpm were investigated and optimised on REEs recovery in laboratory at a leaching temperature of 60¦C. The obtained data, on the laboratory optimisation process were used for training and testing of a neural network. A feed-forward artificial neural network with 4-5-5-1 arrangement, was capable of estimating the REEs leaching recovery. Neural network predicted values were in good agreement with the experimental results. The correlations of R = 1 in training stages, and R =  0.971, 0.952, 0.985 and 0.98 in testing stages were results for Ce, Nd, La and Y recovery predictions respectively and that theses values are considerably acceptable. It was shown that the proposed neural network model accurately reproduces all the effects of operation variables, and can be used in the simulation of a REEs leaching plant.

Jan 1, 2008

By A L. de Ambrosis, S J. Clarke, R Bertuzzi, J Redelinghuys

The M2 Upgrade Project involved widening 15 km of the existing M2 Motorway, which is a key route in Sydney’s road network. The Norfolk Twin Tunnels in North Epping convey traffic over a 460 m length of the motorway. The project involved widening the twin tunnels to provide a third lane and breakdown lane in each direction.The widening of the tunnels was fundamentally different to other ‘greenfield’ tunnel projects in that the operation of the tunnel was maintained throughout construction, with motorway traffic permitted close to the excavation faces on a daily basis. The widened works had to integrate with the existing tunnel support, construction details, and mechanical and electrical infrastructure.The existing tunnel afforded the opportunity to review existing ground conditions in the tunnel. Exposures were mapped within the tunnel, and key design parameters were back-analysed from the original monitoring data to provide increased confidence in the assessed impact from the widening works.Traffic capacity of the tunnels was maintained by detailed staging of the works, and included the ability to reopen the tunnels at short notice.A permit to tunnel system was developed to manage the risks associated with re-opening the tunnel to traffic. A comprehensive suite of instrumentation was maintained to provide reliable monitoring data to support this process. Emphasis on the robustness and reliability of tunnel instrumentation provided increased confidence in the adequacy of the tunnel support being installed. The monitoring was routinely compared with design predictions to check the adequacy of the support measures being installed and confirm the design.The approaches and methodologies developed for the widening of the Norfolk Tunnels were effective in maintaining the safe operation of the tunnels throughout the two years of construction, and provide a framework for increasing the capacity of existing tunnel infrastructure in the future.CITATION:Clarke, S J, de Ambrosis, A L, Bertuzzi, R and Redelinghuys, J, 2014. Design and construction for the widening of the M2 Norfolk Twin Tunnels, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 591–602 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By R M. Smart, A T. Harrison

Backfill systems using unconventional cementitious binders have been successfully used in relatively deep and hard rock tabular mines for longwall, scattered stoping and shaft pillar removals. Two unconventional cementitious systems are discussed: A ground granulated blast furnace slag (GGBS) with an activator containing lime. This has been used with a total tailings æstableÆ slurry at a relatively low dosage of less than seven per cent, by mass, based on dry solids. The room and pillar stopes supported with this fill were up to 20 m high and the tailings were relatively high in pyrite. A GGBS binder plus a silicate based activator and gelling agent that virtually eliminated all water drainage (and hence post filling shrinkage). The system used a slurry, but the addition of the activator created a final placed product that had the behaviour of a paste. The system has been successfully used for almost ten years in the following applications: stoping widths (mining heights) above 1.6 m; and shaft pillar removals in seismically active areas at the end of the life of the shafts. This paper discusses the technical merits and costs of the systems and compares them to other fill systems (including true paste systems). the acceleration (normally g, 9.81m/sec2) is increased to a significantly larger (but generally unmeasured and unknown) value, as shown in Figure 1.

Jan 1, 1998

By C J. Greet

Oil can enter a flotation circuit from a number of sources (for example, from mining equipment, oil leaks from the grinding equipment and coatings on the grinding media, but to name a few). Folklore generally states that any oil that contaminates the ore entering the flotation circuit is considered to have a negative impact on flotation. That is, a loss in concentrate grade and recovery.This represents a dilemma for some grinding media suppliers, who use a variety of quenching medium (air, polymer, oil or water) to achieve the desired physical properties of the ball. In the case of high chrome grinding media it is necessary, in some instances, to quench in oil to give the ball the right degree of toughness, which invariably leads to these balls having a thin film of oil on their surface. Once the grinding media arrives on site and site personnel recognise that the balls are “covered” in oil, they generally insist that the oil will have a deleterious impact on flotation performance.Obviously, any supplier “worth their salt” would take remedial action at the point of manufacture to minimise this problem. However, does quenching oil actually present a significant “threat” to the flotation process? This paper provides both laboratory and plant data describing the effect quenching oil has on the flotation of copper sulphide ore, with surprising results!

Aug 8, 2011

The mining industry continues to faces significant challenges due to increasing resource constraints (quality of ore bodies, water, energy, human resources) and increasing license to operate requirements (safety, health, environment, location) from society, employees and shareholders. Technology advancements and hence research are necessary to ensure that the industry remains viable in this changing environment. Collaborative research is an important part of a company's research portfolio and offers the opportunity for the industry to work on generic issues that it is facing. Obvious benefits include the reduced cost to individual companies by sharing the costs, the opportunity to leverage government funding and the opportunity to conduct longer term projects resulting in skills development (PhD and MSc). Limitations of collaborative research include the reduced focus on company specific issues and the loss of competitive advantage from owning the outcomes of the research. The challenge for researchers and research managers is for them to demonstrate the value derived from longer term, pre-competitive collaborative research. The competitive advantage is not necessarily derived only from the outcomes of the research but rather from the company's ability to direct the research, translate the generic research outcomes to address company specific issues and to implement improvements at its operations. Implementation remains the greatest challenge. In this paper, case studies of selected collaborative research projects are presented to demonstrate key success factors required for implementation of research outcomes. This is an ABSTRACT ONLY. A full-length paper was not prepared for this presentation.

Sep 13, 2010

The development and distribution of gold placers in Otago û Southland is related primarily to the evolution and architecture of three distinctly different drainage networks that developed during and since Gondwana breakup: +        Late-Gondwana û Pre-marine; +        Middle Tertiary Post-marine; and +        Modern. Late Gondwana û Pre-marine drainage was dominantly recti-linear and controlled by normal faults and sedimentary basins formed before or during Gondwana breakup. Placers formed dominantly in 2nd order transverse drainages with primary sources in their catchments. This drainage network was progressively destroyed by inundation and burial by marine strata during Late Cretaceous û Middle Tertiary marine transgression that ultimately covered most of New Zealand. Middle Tertiary Post-marine drainage evolved on and incised the newly emergent low-relief landscape during regional marine regression driven by development of the present plate boundary through South Island. Most of Central Otago was drained into Southland and to the southern coast via a large braided river system with an extensive network of tributaries in its Central Otago reach. East Otago was drained by several smaller systems. Placers formed dominantly in proximal and medial reaches of 1st and 2nd order drainages with primary or pre-existing placers in their catchments. This drainage network was destroyed by inundation and burial of the Central Otago reach of the major system by lacustrine strata following tectonic damning of its middle reach by range uplift and development of a lake complex that covered >5000km2 of Central Otago. The Modern drainage network evolved from the Middle Tertiary network through complex response, firstly to uplift of NW-trending and NE-trending ranges throughout the region since the Late Miocene, and secondly to the effects of major Pleistocene glacial advances in West Otago. Placers formed in alluvial fans at range margins, proximal and medial pre-glacial fluvial systems and glacial outwash sequences. Evolution of each of these drainage networks has been accompanied by widespread sedimentary recycling of alluvial gold from older to younger placers, augmented locally by input of first-cycle gold derived from erosion of primary sources in the repeatedly exhumed basement rocks.

Jan 1, 2006

By Jaczkowski B

The lower orebody (LOB) at Chingola Divi- sion of Nchanga Consolidated Copper Mines Limited (NCCM) accounts for approximately 30 per cent of the total copper production for the company. The uniformity of the geology of the orebody lends itself readily to a computer based ore reserve calculation and accounting system. The mining units are physically defined such that a hierarchical type of com- puter file organisation can reflect the existing physical interdependencies. In 1972, a project team consisting of one representative from each of the mine planning, operational research, and computer services departments was formed to investigate and to define the technical mining requirements of the dynamic ore reserve system (DORS). The system was finally implemented in 1975ò

Jan 1, 1977

By K S. Smith, J Woodhead, K Olson Hoal

Mineralogy is the link between ore formation and ore extraction. It is the most fundamental component of geomet programs, and the most important aspect of a life-of-project approach to mineral resource projects. Understanding orebodies is achieved by understanding the mineralogy and texture of the materials, throughout the process, because minerals hold the information required to unlock the value they contain. Geomet mineralogy programs absolutely require the appropriate expertise and at least three steps of mineral characterisation prior to using semi-automated or other methods: field examination, thorough core logging, and optical microscopy. Economic geological inputs for orebody characterisation are necessary for orebody understanding, and are exemplified by current research in the Zambian Copperbelt, where revised sequence stratigraphy and understanding of alteration, metasomatism and metamorphism can be used to predict topical issues at mine sites. Environmental inputs for sustainability characterisation are demonstrated by recent work on tailings from the Leadville, Colorado, USA area, including linking mineralogy to water quality issues. Risk assessments need to take into account the technical uncertainties around geological variability and mineral extractability, and mineralogy is the only metric that can be used to make this risk contribution.CITATION:Olson Hoal, K, Woodhead, J and Smith, K S, 2013. The importance of mineralogical input into geometallurgy programs, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 17-26 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

By A Batnasan, K Haga, A Shibayama, K Higuchi, H Takeuchi

High silica (SiO2), alumina (Al2O3), and phosphorus (P) contents in iron ore adversely affect the quality of iron products. The removal of those impurities from iron ore is an essential point in further iron ore processing. In this paper, the removal of P, SiO2 and Al2O3 impurities from iron ore by alkaline drying followed by reverse cationic flotation is discussed. The reverse cationic flotation experiments are performed using the iron ore samples without and with alkaline drying pretreatment. All other flotation conditions except pulp pH (4–12) and particle size distributions (-45 to -250 μm) are held constant. A typical collector and frother, such as dodecylamine acetate (DAA) and methylisobutylcarbinol (MIBC), are used in the flotation experiments. Alkaline treatment is conducted before flotation using sodium hydroxide at fixed conditions. The impact of alkaline drying on the performance of iron ore flotation is evaluated based on the removal rates of P and SiO2 + Al2O3, iron grade, and iron recovery compared with the iron ore flotation without alkaline drying (direct flotation). X-ray diffraction (XRD) analysis indicates hematite and goethite are the main minerals in the iron ore, which assays 62.8 mass per cent Fe, 0.232 mass per cent P, 7.1 mass per cent SiO2 + Al2O3 (total) determined by X-ray fluorescence analysis (XRF). Results indicate that a combined approach is more effective for removing P and SiO2 + Al2O3 impurities from iron ore than the direct processing technique because the maximum removal rates of P and SiO2 + Al2O3 are 48.2 per cent and 66.5 per cent from the alkaline dried iron ore when 8.4 per cent and 13.1 per cent from the non-alkaline dried iron ore.

Sep 18, 2023

By B Davis, A H. Benzer, A N. Mainza, C M. Evertsson, L M. Tavares, M M. Hilden, M S. Powell, C Rule, G Asbj÷rnsson

The Mogalakwena North Concentrator of Anglo Platinum Operations was built with the capability to allow for future projected expansion. Several research groups, currently working with Anglo American on collaborative research over a range of projects, were brought in to review the existing operation, with a view to releasing some specific bottlenecks and providing specialist design input to the potential plant expansion.Based on a thorough review of the high pressure grinding rolls (HPGR) and crushing circuit, a wide range of de-bottlenecking opportunities were identified. This was followed by a series of surveys to provide performance measurements and to model the circuit in detail. From this effort a full simulation of the plant has been developed, including updated models of the HPGR, crusher, bins and screens. These models have been implemented in the researchersÆ Model Development Kit (MDK) version of JKSimMet, and in a prototype dynamic simulator based on the Matlab Simulink software.The observations, measurements and simulations have provided guidance and quantified the benefits of some proposed circuit modifications. Based on these findings a number of upgrades are being planned, with the aim of ensuring full utilisation of the installed equipment. The circuit demonstrates a potential expansion of over 30 per cent through minor improvements, and a 70 per cent increase in capacity with the addition of some strategic equipment.The HPGR-crushing upgrade project demonstrates the potential benefits of nurturing disparate Research groups into a strong inter-disciplinary technical team capable of supporting operational needs while developing future technology.CITATION:Powell, M S, Hilden, M M, Evertsson, C M, Asbj÷rnsson, G, Benzer, A H, Mainza, A N, Tavares, L M Davis, B, Plint, N and Rule, C, 2012. Optimisation opportunities for high pressure grinding rolls circuits, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 81-94 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012