Search Documents

By H. W. Schreiber, G. R. Castle

INTRODUCTION The small mining company faces the dilemma of how to finance the development of its properties. Many of these small companies don't have the financial resources to pay for development costs from their own funds and frequently they do not even have the financial strength to permit them to borrow the money needed for development. A project financing can sometimes be arranged in such a way as to solve this dilemma. A typical project financing will not provide the answer to the "little guy's" problem because most project financings require that the sponsors of the project provide completion undertakings and sometimes other undertakings. These undertakings are often a prerequisite to obtaining financing, and if the sponsor is not financially strong enough to provide the comfort that the lenders require, then the sponsor will have difficulty obtaining financing no matter what undertakings are offered. However, with a little imagination and the right set of circumstances, a project financing can sometimes provide the solution to the small mining company's problem. The Strathcona Sound Project is unusually suited as a case study because the sponsor, Mineral Resources International Limited,(MRI) was able to arrange a project financing for the development of the project even though the lenders probably would not have been willing to loan a similar amount of money direct to MRI based on the full faith and credit of MRI's balance sheet. The way that MRI was able to arrange this financing makes for an interesting story. THE CASE In early 1974, MRI owned 100% of a small to medium sized zinc - lead - silver massive sulfide deposit (Property) located 475 miles north of the Arctic Circle less than two miles from deep water on Strathcona Sound which is a shipping zone in the Canadian Arctic. The Property was situated at a desolate location except for an Eskimo settlement (Arctic Bay) which was about 20 miles west of the Property. In other words, the project required that complete infrastructure would need to be installed in this far northern location. Independent reserve and feasibility studies (Study) had been completed on the Property which confirmed a total of 6,825,000 tons of reserves classified and summarized as shown below on Table I: [ ] These reserves were based on 229 diamond drill holes totalling 58,909 feet and were established on a cut-off grade of 7% zinc and a minimum mining height of seven feet. The overall mining recovery rate was estimated at not less than 85% and not more than 90%. The feasibility study indicated that it would cost an estimated $45,044,000 to develop an underground mine, a concentrator, a town-site, a power plant, storage facility, loading dock, a tailings disposal area and an airstrip on the Property with an annual capacity of 525,000 tons of ore per year. The construction period was expected to take two years and projected capital costs were broken down as set forth below on Table II:

Jan 1, 1985

By T. H. Aldrich

This paper is intended only to give a preliminary account of experiments made, and conclusions reached, concerning the treatment of certain refractory low-grade gold-ores, the profitable reduction of which may furnish a useful guide to the solution of similar mining and metallurgical problems, not only in the gold-bearing belt of the Southern United States, but perhaps in other regions also. It must be regarded as simply a " report of progress," preceding a more elaborate and conclusive report of regular practice. The mines of the Hillabee Gold Mining Co. are located upon what is generally known locally as Hog Mountain, on the northern edge of Tallapoosa county, Ala., about 15 miles from Goodwater and 14 miles from Alexander City, stations on the Central of Georgia railway. Gold has been known since 1839 to exist on this property, where it was discovered in that year by a man named Johnston. The property was worked for placer-gold by the old miners, and there are now the remains of four attempts to operate it by stamp-mill and plate-amalgamation. The present owners purchasid it in 1896, and since that time they have experimented at frequent intervals, in order to devise a process that would satisfactorily recover the gold. In 1903 regular operations were begun. Geologically, the mountain consists of an intrusion of what has been pronounced true granite in altered sedimentary slates. The cooling of the granite produced shrinkage-cracks, which have become veins. There is considerable question as to the period of the slate formation; but it is undoubtedly, in my opinion, of Carboniferous age. The veins, about 50 in number, strike N. 60° to 80° E.; dip approximately 65' from the horizontal; vary from a few inches to 25 ft. (being in gen-

Jan 1, 1909

By Gerhard Derge

A SERIES of studies of the corrosion of tin is under way in the Metals Research Laboratory at the Carnegie Institute of Technology. The complete program includes examination of the corrosion properties of high-purity tin and the changes produced in these properties by the addition of varying amounts of alloying elements. Other studies of this subject have been made recently under the sponsorship of the International Tin Research and Development Council, but these researches have been confined largely to the weakly acid environments commonly encountered in the canning industry.1 There is little information available regarding the corrosion of tin under alkaline conditions, but such data would be of value, for a large amount of the metal is used under such conditions. The potential measurements to be described were made because they seemed to offer the most rapid method for obtaining a general view of the conditions to be encountered in such service. These experiments will also serve to establish a technique that will be of value in further studies. It must be emphasized that the results reported are those of controlled laboratory experiments and that the conclusions drawn cannot yet be applied to service conditions; rather, they point to the directions in which more exhaustive experimental work may be done to best advantage. EXPERIMENTAL PROCEDURE The first work was devoted entirely to the problem of obtaining reproducible results from a series of potential measurements. Only the methods finally adopted as standard will be described here, except when the variations from these have furnished results of interest. The cell used is shown schematically in Fig. 1. The electrolyte is contained in the vessel A (an inverted bell jar), whose ground top is fitted to the transite-board lid B. The controlled atmosphere can be admitted

Jan 1, 1938

By William Hamilton Merritt

At the Atlanta Meeting in October, 1895, a short paper was presented by Mr. R. W. Leonard on the " Assay of Auriferous Ores and Gravels by Amalgamation and the Blow-pipe" (Trans., xxv., 645), embodying the results of some very conclusive tests as to the value of the process. His arguments regarding the desirability of the process appear to be indisputable, but the practicability of the field-outfit used by him is open to question. The Province of Ontario, in which Kingston is situated, is still largely unexplored; and at the Kingstoil School of Mining we give much attention to the instruction of prospectors and the testing of ores. To this end, not only is there a small mill (to which Mr. Leonard alludes) attached to the school, but prospectors' classes

Jan 1, 1897

By Leonard P. Skolnick

PROPERTIES of materials containing a hard con-stituent dispersed in a metallic matrix are dependent on the distribution of the hard phase.'-' The grain growth of titanium carbide in liquid nickel was studied in order to understand microstructural development in this and similar systems. Smith" has examined the influence of surface energy on the distribution of phases in alloys. The grain growth of tungsten carbide in cobalt has been the subject of many conflicting theories. Those prior to 1950 have been summarized by Goetzel.' Recently, Gurland and Norton3 and Gurland8 have indicated that growth occurs primarily by diffusion through the liquid phase in order to lower the inter-facial energy between the carbide and the liquid metal. In the development of the Ti-C-Ni ternary phase diagram, Stover and Wulff9 have shown that both eutectiferous dendritic titanium carbide, and primary titanium carbide which had developed crystals of cubic symmetry, were rounded by heating below the solidus, and that if primary carbide was already present the typical eutectic decomposition products were not formed. Experimental Procedure The infiltration technique was used to study the grain growth of titanium carbide in nickel. In contrast to sintering, infiltration more readily assures uniform dispersion of the two phases, and the problems associated with mixing by milling; i.e., mill contamination, breakdown of original carbide size in the operation, development of interfering surface films, etc., are avoided. In addition, the complicating effect of densification by shrinkage is eliminated. The titanium carbides used were commercial grades. Their chemical analyses, size distributions and shapes are summarized in Table I. Size analysis was conducted by microscopic count on a minimum

Jan 1, 1958

By T. M. Allen, W. H. White

THE Greenwood-Grand Forks area of southern central British Columbia, known as the Boundary District, has a long history of mining exploration and production. At the turn of the century this was the premier copper mining camp in the British Empire, its total production amounting to some 20 million tons. Most of this ore came from the great Granby mines at Phoenix, but the Motherlode mine at Deadwood camp, 6 miles to the west, and several mines in Summit camp, 5 miles north of Phoenix, made important contributions. The large deposits were exhausted in 1918 and the district since has seen only desultory exploration and salvage operations. The orebodies are mineralized skarn zones in limestone members of a thick series of Upper Paleozoic sedimentary and volcanic strata. Chalcopyrite is the primary ore-mineral. Copper carbonates and silicates occur sparingly in outcrops, but the oxidized zone generally is very shallow. Much of the surface is mantled by glacial drift which in most places ranges in thickness from 2 to 15 ft. In some of the hanging valleys, however, the glacial drift may be as much as 100 ft thick and may assume drumlin-like forms. In 1951 an ambitious program aimed at the discovery of new orebodies and important extensions of abandoned deposits was launched by Attwood Copper Mines, Ltd. In this district so thoroughly searched by an earlier generation of prospectors, any orebody which had remained undiscovered must have little or no surface indication. Consequently, in addition to the basic detailed geological work, the program of exploration included magnetometer and self-potential surveys. Geological bets and geophysical anomalies were tested further, prior to diamond drilling, by a study of copper distribution in tree twigs and/or in the soil. The soil sampling and analytical methods used and some of the results seem of sufficient importance to warrant this paper. The authors had done some plant sampling in this and other districts, using the dithizone neutral-color-end-point method (Warren and Delavault, 1948, 1949; White, 1950),1-3 but they were unfamiliar with its soil application. Finally, after much experimenting in the field, they adopted the methods described here. These methods are not entirely original or defensible on theoretical grounds, but under field conditions of rapid sampling and analysis the results are reliable enough to be of use. Fig. 1, which shows the results of duplicate analyses of duplicate soil samples taken at 50-ft intervals across an anomalous zone, indicates the relative dependability both of the sampling and analytical methods. Sampling and Analytical Equipment A 2-ft piece of 1-in. solid drill steel, one end sharpened to a broad, conical point. The steel is marked at 1 ft from the point. A 2-ft piece of ½-in. black iron pipe, one end filed to a bevelled cutting edge. The pipe is marked at 1 ft 3 in. from the cutting end. A 3-lb hammer. A plastic or rubberized sheet about 18 in. square. Moisture-proof assay pulp envelopes. A 10-mesh seive made from window screen with the paint burnt off. A small assay spatula. A pan balance sensitive to 10 mg. Two ignition trays about 4 in. square, made of sheet iron turned up along the edges. A Coleman two-burner gasoline stove. An asbestos board about 5x8 in., used as a hot plate on the gasoline stove. A circular aluminum rack to hold 8 test tubes while refluxing (design of Almond and Morris). Pyrex Glassware Large refluxing test tubes, 25x200 mm, marked at 40 ml volume. Breakers, 20 ml. Pipettes, 1, 5, and 10-ml capacity. Graduate, 50 ml. Shaking cylinders, 100 ml, glass stoppers. Burette, 25 or 50-ml capacity, with holder. Chemical Supplies 1 N sulphuric acid. Hydroxylamine hydrochloride, solid crystals. Fisher Alkacid test paper. Copper standard solution. Dithizone standard solution 60 mg per liter. Water reasonably free of metals. Soil Sampling Method: The problem of how to take a soil sample is extremely crucial. The method outlined below, adopted after a number of tests, has the advantages of uniform pattern, uniform depth, and uniform size of sample. The area to be tested was marked off by chain and compass lines 100 ft apart, normal to the strike of possible ore deposits. Numbered stakes were set at 50-ft intervals along these lines and a soil sample was taken at each stake in the following manner. The drill steel was driven into the ground normal to the slope of the surface to the marked depth of 1 ft, moved slightly from side to side, then carefully withdrawn. The iron pipe was inserted to the bottom of this hole, tapped down to the marked depth of 1 ft 3 in. and withdrawn; the 3-in. soil plug in the

Jan 1, 1955

By F. E. Marcy

IT is not my purpose to write a lengthy article or to attempt the solotion of the problem I am presenting, but to call attention to what I believe an important issue, hoping that it may arouse in some one, or in some company, a sense of responsibility. I am referring particularly to modern up-to-date milling plants discharging tailings which under existing conditions cannot be further treated or from which a recovery cannot be made at a profit, but where a quantitative and qualitative analysis shows that a portion of these tailings might profitably bee treated, at some future time when our metallurgical knowledge has advanced, when we have cheaper power, chemicals, labor or other advantageous conditions. Early Methods In our early milling methods very little attention was given to the care of tailings. It was thought that if the mill could be located by a stream or a river where the final disposal of the tailings could be forever lost sight of, it was highly desirable. We can now see acid estimate what was lost in these rich tailings, not recoverable from the streams and the great rivers. Fortunately for many, the depositing of tailings in these streams and rivers was objected to by the farmers and finally prohibited by the State Legislatures. In looking back over our past milling methods, it seems that, the first endeavor was to make the maximum amount of money for a particular period, or year, regardless of the future, the depletion of the mine, or the conservation of the total mineral content. The dumping and sluicing of 3,000 tons per day, for a period of many years, of a copper tailing carrying

Jan 8, 1917

By Woolsey McA. Johnson

Independently of the recognized chemical reactions involved in the production of metallic zinc, the process is affected by physical conditions in efficiency, and by commercial as well as technical economy. To offer some observations concerning these conditions is the purpose of the present paper. Among the important elements of this problem is the physical nature of the particles constituting the mass of zinc oxide to be reduced. This may be the result, either of the manner of the original deposition of the mineral, or of the treatment to which it has been subjected in the roasting-furnace. The physical character of the reducing-agent is another important factor, since the carbon of some coals is much more active in reduction than that of others. The degree of fineness, whether of ore or coal, or both, likewise plays a significant part. These factors, together with the physical admixture of foreign substances with the ore, may give rise also to chemical " side-reactions," sometimes hindering or retarding, and sometimes accelerating, the reduction. Finally, thermal conditions, including the relative conductivity of the materials, deserve to be taken into account. In firing a furnace with retorts charged with a mixture of roasted ore and coal, the first reaction is naturally the boiling-off of the contained water; the next is the distillation of the light hydrocarbons from the coal; the next is the reduction of the iron oxide to protoxide and sub-oxide successively, and then to metallic sponge; and the final reaction is the reduction of the zinc oxide in the ore by the carbon to metallic zinc. This reaction commences at 1,022o to 1,060o C., according to the physical nature and condition of the coal and ore. Since the retort and the charge are far from being good con-

Jan 1, 1908

By ARTHUR S. DWIGH

Discussion of the paper of W. W. NORTON, presented at the Salt Lake meeting, August, 1914, and printed in Bulletin No. 92, August., 1914, pp. 1993 to 1999. ARTHUR S. DWIGHT, New York, N. Y.-Mr. Norton's chief argument is directed against the idea that the D. & L. sinter is any better material for the blast furnace than the H. & H. product. He supports this by citing two experimental furnace runs. Reducibility.-To discuss a furnace record like that quoted by Mr. Norton for the five days' run in August, 1912, is manifestly difficult for an outsider, but a possible explanation for the poor reduction on Furnace No. 5, smelting D. & L. sinter, may lie in the fact that both sets of furnaces carried the same fuel charges. Other things being equal, if 11 ½ per cent. coke was right for the furnaces smelting H. & H. product, it Was too much for the furnace smelting D. & L. product, as I shall endeavor to show later, and incipient overfire, accompanied by higher leads in slag and matte, was induced. It may sound like a paradox to say that excessive fuel sometimes produces poor reduction, but it is a sad fact. In certain plants where practically the entire charge to the blast furnaces receives a preliminary treatment by being sintered on the D. & L. machines the peculiarities of this problem have had to be very carefully studied, for serious metallurgical difficulties presented themselves when the change was first made to D. & L. sinter in large quantities. Some of these plants had blast pots before they had D. & L. machines, and many opportunities were afforded for comparative study of this very point. There is reason to believe that, clue to the long period of blowing and the higher temperatures developed in the pots from greater mass action, the iron in the H. & H. product is present chiefly as Fe203, perhaps in the form of ferrites, while in the D. & L. product the iron is present as FeO. The fuel charge in the blast furnace must be so proportioned as to exactly meet the chemical and thermic requirements of reduction and melting. If ally of these functions have been performed before the material enters the furnace, a corresponding allowance should be made or the fuel balance will be disturbed and bad work will result. One of the functions of the coke is to reduce enough metallic Fe for the matte requirements, leaving the remainder of the iron as FeO to go into the slag. In smelting almost any other material than D. & L. sinter the iron must-be reduced from the higher oxides, Fe203 or Fe304, to the protoxide, FeO, before a true comparative basis is reached. Experience has shown that with about one-half D. & L. sinter on the charge the coke should-be cut about 10 per cent. This theoretical benefit is borne out by the practical blast-furnace results on a large scale in numerous plants. In fact, wherever this very important factor is ignored the evil symptoms of excessive fuel will be indicated,

Jan 11, 1914

By C. R. McClure

The objective of this papef is to summarize briefly the practical use of rock mechanics in design and construction of various types of structures. These range from foundation for industrial facilities, nuclear power plants, bridges and dams to tunnels and underground caverns. The use of rock mechanics has varied from performing a few laboratory unconfined compressive tests on core samples to complete field and laboratory tests for underground power caverns. The primary difference between the rock mechanics studies we hare for construction projects and those most commonly found in the literature is that our tests must provide immediate answers to specific questions facing a design or construction engineer. For example, when we make a plate-bearing test we arrive at a load-deformation relationship. We realize that this is not a true modulus of elasticity. Yet, when considering the resistance the rock will provide against forces occurring in a pressure tunnel it is a far more useful value than the true modulus of elasticity of the rock. Another example of this difference in interest is in the use of flat jacks. Many people criticize the use of flat jacks because they measure the stresses in the disturbed zone very near the surface and do not represent the undisturbed stress condition in the rock. However, in actual construction it is frequently those near-surface stresses with which we must cope. We are interested in both the stress conditions present prior to excavation and those as modified by construction of an exploratory adit or drift. Fundamentally, we are interested in the practical application of rock mechanics in the solution of problems of design and construction of civil engineering works.

Jan 1, 1968

By Robert :H. . Lesemann

I recently gave a talk at a seminar on mine development in the Eighties. I had to present CRU' s long-range market outlook for copper, lead, zinc, nickel, molybdenum and silver. In reviewing the recent history of each metal, and our projections, I tried to find some common pattern of behavior that could prove a guide in projecting future market behavior. When you sweep aside your input-output models and econometric equations, what you seem to be left with is this: "When a market goes through a prolonged period of price weakness, you can usually look forward to a period of considerable improvement. " "When a market goes through a prolonged period of price strength, you can always anticipate a prolonged period of price weakness." Stated another way, "The better things are, the worse they will get."

Jan 1, 1982

By T. B. Counselman

The importance of concentration of iron ores too low in grade to be smelted direct is shown by Table I, showing 1940 ship- ments from the Lake Superior district. Canadian ores are omitted. Only in Minnesota is concentrating, other than crushing and screening, prac- ticed at present. Tonnage produced by various methods of concentration is shown in Table 2. The curves in Fig.. I show the gradual increase in tonnage of concentrated ores shipped, compared with total shipments from Minnesota. Most of the concentration work is performed on the Mesabi Range. This range is about 100 miles long, and not over 3 miles wide from the line at which the formation tapers out to a feather edge on the north to the place on the south at which, some 600 ft. thick, it is overlain with slates. Classes OF Ore The Mesabi Range contains three classes of iron ore. First is the unaltered taconite, or banded iron-bearing chert. It is estimated that there are some 60 billion tons of this material, which contains, roughly, 25 to 30 per cent iron. This material is virtually untouched, since no commercially successful method has yet been found for concentrating it to a grade suitable for the blast furnace. Intensive exgerimental work is in progress, and the problem is gradually being solved. In 1922 the Mesabi Iron Co. spent several million dollars erecting a large-scale pilot plant for concentrating and sintering the magnetic taconites on the east end of the range. An important tonnage of high-gade sinter was shipped to lower lake furnaces, proving that the taconite can be concentrated to a satisfactory grade. The costs, with equipment and methods then in use, were too high for

Jan 1, 1943

By T. B. Counselman

The importance of concentration of iron ores too low in grade to be smelted direct is shown by Table I, showing 1940 ship- ments from the Lake Superior district. Canadian ores are omitted. Only in Minnesota is concentrating, other than crushing and screening, prac- ticed at present. Tonnage produced by various methods of concentration is shown in Table 2. The curves in Fig.. I show the gradual increase in tonnage of concentrated ores shipped, compared with total shipments from Minnesota. Most of the concentration work is performed on the Mesabi Range. This range is about 100 miles long, and not over 3 miles wide from the line at which the formation tapers out to a feather edge on the north to the place on the south at which, some 600 ft. thick, it is overlain with slates. Classes OF Ore The Mesabi Range contains three classes of iron ore. First is the unaltered taconite, or banded iron-bearing chert. It is estimated that there are some 60 billion tons of this material, which contains, roughly, 25 to 30 per cent iron. This material is virtually untouched, since no commercially successful method has yet been found for concentrating it to a grade suitable for the blast furnace. Intensive exgerimental work is in progress, and the problem is gradually being solved. In 1922 the Mesabi Iron Co. spent several million dollars erecting a large-scale pilot plant for concentrating and sintering the magnetic taconites on the east end of the range. An important tonnage of high-gade sinter was shipped to lower lake furnaces, proving that the taconite can be concentrated to a satisfactory grade. The costs, with equipment and methods then in use, were too high for

Jan 1, 1943

By George S. Barnett

The Equis and El Roble projects are located in the Cordillera Occidental of Colombia. The Equis vein deposits have sulfide ore reserves of 95,955 mt (105,770 st) grading 8.51 g/mt (0.248 oz/st) gold and 12.4 g/mt (0.36 oz/st) silver with 0.94 % copper, 1.10 % lead and 11.06 % zinc. Ore reserves at El Roble are estimated as 1.1 Mmt (1.21 million st) grading 4.89 % copper and 3.39 g/mt (0.099 oz/st) gold. Geologically possible reserves at Equis may total 1.6 Mmt (1.76 million st). El Roble has the potential to contain several tens of millions of metric tons. Exploration included diamond drilling, trenching, channel sampling, rock and soil geochemistry, geophysics and tunneling. Erratic high grade samples affect the weighting of channel and drill core samples. Secondary reconcentration of gold is also a factor. Sample maps and graphs show the distribution of values to be highly variable. Geostatistical treatment of some of these data gave important guidelines for parameters such as sampling densities, drill hole spacing and confidence limits.

Jan 1, 1985

By M. W. BERNEWITZ

ALTHOUGH many persons know that a lot of type metal and etchings are used in the U. S. Government Printing Office few would expect to find anything on metals in the annual report of the Public Printer, George H. Carter. Yet the report for the fiscal year ended June 30, 1931, contains many interesting items. For example: Among the 57,500,000 lb. of materials and supplies delivered to the printing office was little new metal, but the metal in circulation is 6,000,000 to 7,000,000 lb. In the cost of production $31,523 is charged against metal, nearly one-third for salaries and wages. In miscellaneous sales were $4,696 from waste metal and $1,147 from waste gold (from books). Electrotype and stereotype covered 11,438,314 sq. in. The vaults and storage rooms contain 1,700,000 plates and 130,000 pages of type containing 4,600,000 lb. of metal valued at $275,000. In what was known as the Congressional Globe vault were 46,000 stereotype plates; these were salvaged by remelting for other platemaking service. The Congressional Record superseded the Congressional Globe in 1873.)

Jan 1, 1932

New Mexico School of Mmes, and State Bureau of Mmes and Mineral Resources, Socorro, N. M E. H Wells, President and Director Available publications of the State Bureau of Mines and Mineral Resources of the New Mexico School of Mines are: Bulletin 4, Fluorspar in New Mexico (1928), 60 cents; 5, Geologic

Jan 1, 1933

By R. Kossowsky

In the course of a study concerned with structural stability of precipitation hardening nickel base super -alloys after exposures to elevated temperatures, some interesting effects of hydrostatic pressure treatment on Rene were observed. The evidence presented below suggests that hydrostatic pressure treatment of the solution heat-treated alloy can affect the dispersion of the y' (Ni3Al) phase upon subsequent precipitation heat treatment and long time aging. Rene 41 alloy has the following nominal weight percent composition: Al B C Co Cr Fe Mn Mo Ti Ni 1.4 0.006 0.7 11.3 19.2 1.0 0.05 9.4 3.3 balance The effect of successive pressure, precipitation heat treatment, and long time aging on the microstructure of this alloy was determined by subjecting a number of alloy buttons to five different thermopressure treatments. Pressure and precipitation heat-treatment parameters are listed in Table I. Fig. 1 shows y' morphology* of specimens in groups I and 11. The treatment results in a fine dispersion with particle size on the order of 950 and 1350A, respectively, see Table I. Fig. 2 shows the morphology of y' precipitate in

Jan 1, 1967

By Edwin H. McKee

Eruption of rhyolitic ash-flow tuffs in the area of the McDermitt (Cordero) caldera began about 17.4 million yr (m.y.) ago and continued for about 1.5 m.y. During this period of silicic eruptions, a circular area about 30 km in diameter collapsed to form a caldera that subsequently filled with sedimentary and volcanic rocks. A total of more than 200 km30f silicic rocks was erupted from the volcano. The final phase of igneous activity, about 15.0 m.y. ago, included resurgent doming and intrusion in the south-central part of the caldera. Three to 4 m.y. later (-1 2 m.y. ago), hydrothermal solutions using the northern part of the caldera ring fractures as conduits deposited silica, cinnabar, pyrite, alunite, and other minerals in tuffaceous lake beds and volcanic rocks accumulated within the caldera. The ore-forming solutions may have been a residuum from the silicic magma, or connate water, or ground water heated by the still-hot resurgent magma in the central part of the caldera. The source of the mercury and other elements has not been identified.

Jan 1, 1977

By Y. Mishima, R. Shiromizu

THE equilibrium y phase in Cu-Be alloys forms by discontinuous precipitation, the new phase nucleating at the grain boundaries and growing into grains on both sides of the boundary. When the alloy is aged above 500°C, however, growth may take place into only one of the grains.1'2 In A1-Ag alloys it is known that the precipitate has the same orientation as the grain in which no growth takes place.3, 4 This was confirmed in the present investigation on a Cu-Be alloy. A Cu-1.79 wt pct Be alloy was solution-treated at 810°C for 2+ hr, quenched into water at O°C, and aged at 600°C for 1 hr in a salt bath. The specimen was thinned by chemical polishing and electropolishing at room temperature in a solution of H3PO4 saturated with CrOs. The foil produced was examined in a JEM 150 electron microscope operating at 150 kv. Fig. 1 shows precipitates growing on only one side of the grain boundary. The black platelike precipitates were identified as the y phase. Electron dif-

Jan 1, 1969

By Frank R. Milliken

This paper is a running commentary on metallurgical problems and developments, stressing ilmenite flotation, since the start of operations five years ago, at the mill of National Lead Company, Titanium Division, MacIntyre Development, Tahawus, New York. In early 1941, when world conditions threatened to cut off the supply of ilmenite (obtained largely from India) to this country, the National Lead Company started to develop and bring into production their MacIntyre Development. This operation supplied the bulk of the ilmenite used during the war period for the manufacture of the much needed titanium pigments. MacIntyre Development is at Tahawus, New York, on the headwaters of the Hud- son River in the center of the scenic Adirondack Mountains. A general description of the operation was given in the Adirondack Issue of Mining and Metallurgy for November 1943. Operating tonnages and production have increased since 1943, however. Nearly 10,000 tons of.ore and waste is broken and loaded daily in the open-pit mine. About half of this tonnage is ore, from which is produced nearly 800 tons of ilmenite concentrate and 1600 tons of magnetite concentrate daily. Ore—types From an ore-dressing standpoint, there are five rather distinct ore types and two waste-rock types in the mine. The ore types are shown in Table I. The anorthosite waste is a coarse-grained white rock, largely labradorite feldspar. The gabbro waste is generally finer grained, and contains, in addition to feldspar, 35 to 75 pct iron silicates such as hornblende, in garnet and biotite. A minor mineral mineralogically, but important metallurgically, is apatite. A few calcite

Jan 1, 1949