Search Documents

By Kent A. Pease

Design methods for foundation anchors and sockets constructed in rock are based largely on empirical correlations which yield a reasonable estimate for initial capacity, but do not address the general concerns of failure mode and load-displacement behavior. This paper focuses on the behavior of foundation-rock interfaces and shows that interface behavior under increasing load results in a progression from an elastic response to secondary behavior, in which interface failure occurs, and finally to a residual stage at large deformations. Procedures to follow this progression are outlined to provide a more fundamental understanding of the problem.

Jan 1, 1984

By F. A. Kjellin

The problem of smelting steel by electricity attracted years ago the attention of inventors, and as early as 1879 C. W. Siemens constructed his first furnace for the smelting of metals, especially steel. His furnace was of the arc type in which the voltaic arc was formed between a carbon electrode and the metallic content of a crucible, the length of the arc being regulated by an electromagnetic device. This electric furnace, as well as others of similar construction, has the inconvenience that the source of the heat—the voltaic arc—possesses a temperature of 3,700' C., which is much

Jan 1, 1904

By W. H. Nielson, L. S. Diaz

Several techniques are presented to adjust small errors inherent in data collected from material balance measurements on the flotation process. The basic technique used is a Lagrange multiplier adjustment of the filtered data taken from the equipment measurements. The raw data are adjusted such that material balances are closed. The adjustments to each data point is inversely proportional to the square of the standard error of measurement. Problem areas in equipment utilization are discussed. Typical results from on-line measurements are presented. This technique can be applied to either on-line process measurements or metallurgical test data.

Jan 1, 1973

By Randall J. Essex

A massive mudslide blocked a river in Utah, impounding a 61 m (200 ft) deep lake. Under emergency conditions, a system was designed and constructed to: (1) drain the impounded lake; and (2) provide a permanent diversion for the river around the mudslide. The system consisted of a low level tunnel, a connecting vertical shaft daylighting close to the lake shore, control valves mounted within the tunnel, and an inlet channel between the lake and the shaft. This paper focuses on the problems and concerns surrounding the inlet channel excavation and the stabilization of the remaining vertical rock walls.

Jan 1, 1984

[PRESIDENT GEORGE OTIS SMITH, District 4 WASHINGTON, D. C. PAST PRESIDENTS SAMUEL A. TAYLOR, District 3 PITTSBURGH, PA. E. DEGOLYER, District 0 NEW YORK, N. Y. FIRST VICE-PRESIDENT W. H. BASSETT, District 1 WATERBURY, CONN.]

Jan 1, 1928

By Jan M. Mutmansky, Gordon H. Walrod, Y. J. Wang

The approach proposed in this paper is, as stated by the authors, an update of methods well discussed in the literature. The authors are to be congratulated for their excellent effort in quantifying a difficult problem with realistic cost data. Economic analysis of the components of a mine ventilation system is complicated by both the dynamic nature of the system and the uncertainty as to the time when system changes occur. We wish to address three specific areas of this paper which require further consideration: shaft designed air capacity, shaft location, and economic criteria used within the analysis

Jan 11, 1979

Recognizing the fact that the problems of the committee named by the Board to prepare the "official ticket" for officers and Directors of the Institute are various and difficult; and desiring to assist this committee by setting forth some of the principles that should guide the committee and some of the qualifications that should be required of candidates, the following instructions are formulated and the Secretary is directed to publish them in MINING AND METALLURGY concurrently with the publication of the names of each newly appointed Nominating Committee and to send a copy to each member of the Committee.

Jan 1, 1938

Recognizing the fact that the problems of the committee named by the Board to prepare the "official ticket" for officers and Directors of the Institute are various and difficult; and desiring to assist this committee by setting forth some of the principles that should guide the committee and some of the qualifications that should be required of candidates, the following instructions are formulated and the Secretary is directed to publish them in MINING AND METALLURGY concurrently with the publication of the names of each newly appointed Nominating Committee and to send a copy to each member of the, Committee.

Jan 1, 1946

By Stuart A. Bengson

It is extremely difficult to revegetate disturbed sites and mineral wastes in an arid environment because of sporadic and undependable rainfall. Thus, irrigation is often a must for starting seed germination and vegetation. Quite aside from the harsh climate, mining disturbances by themselves cause various adverse conditions for a revegetation program. The problems of revegetating a harsh soil, for instance, are often compounded by the steep slopes of mine wastes. Since these steep slopes intensify the droughty conditions by rapidly draining away soil moisture and accelerating runoff, supplemental irrigation may be the only solution for establishing vegetative cover on the slope.

Jan 8, 1976

Recognizing the fact that the problems of the committee named by the Board to prepare the "official ticket" for officers and Directors of the Institute are various and difficult; and desiring to assist this committee by setting forth some of the principles that should guide the committee and some of the qualifications that should be required of candidates, the following instructions are formulated and the Secretary is directed to publish them in MINING AND METALLURGY concurrently with the publication of the names of each newly appointed Nominating Committee and to send a copy to each member of the Committee.

Jan 1, 1946

By Michael A. Arkoosh, E. A. Peretti

ANALYTICAL results have previously been presented for the diffusion-controlled solution of a second phase in a finite medium for planar, cylindrical, and spherical geometries.' These results were obtained by numerical methods using digital computer techniques and are applicable not only to the stage of the problem where the unstable phase shrinks to zero size, but also the subsequent stage where the concentration gradients in the matrix phase become negligible (essentially complete homogenization). It is anticipated that the results of such an analysis may be of use to those workers who are interested in the processes

Jan 1, 1970

By C. J. Guntner, R. P. Reed

A commercial 18Cr-8Ni iron alloy (AISI 304L) was examined in tension at 300°, 76°, 20°, and 4°K. Continuous stress-strain recordings were made, X-ray analyses at periodic stress (strain) intervals were obtained, and the magnetic measurements were taken. From this data the percentage of martensitic products [bcc(a) and hcp (E)] was computed as a function of stress (strain). It was found thatup to 15 pct E phase forms at low temperntures. The amount of E formed increases to a maximum at about 5 pct strain, then decreases. This decrease indicates the additional transformation of E to a'. The total amount of E and a' was suppressed at constant stress (strain) at 4°K as compared to 76°K. It is proposed that the suppression of E and a' is associated with the decreased mobility of extended dislocations at very low temperatures. The yield strength decreased as the temperature was depressed below room temperature and then increased rapidly near 4°K. SOME ferrous alloys which are austenitic (fcc ?) at room temperature appear to be unique in that two martensitic products (hcp e and bcc a') may form on cooling to lower temperatures or on application of mechanical stress. The most common room-temperature austenitic ferrous alloys are 18Cr, 8Ni stainless steels. Most aspects of the spontaneous transformations have been previously described for these steels.' Several previous papers have described special aspects of the stress-induced transformations at low temperatures for the stainless steels, such as the existence of the hcp phase (c) after straining at 76oK,2-7 the morphology after straining using electron microscopy,7 and the decrease in E at higher strains at 76oK.4 However, for a complete representation, one must know the stress-strain characteristics and the dependence of both martensitic products on applied stress and temperature. It is the intention of this paper to provide that documentation. To accomplish this, continuous stress vs strain recordings were made at four temperatures: 300°, 76", 20°, and 4°K for annealed AISI 304L (a commercial 18Cr-8Ni alloy). At periodic stress intervals at each temperature the integrated X-ray line intensity of a selected peak for each phase (y, E, and a') was measured. In addition, photomicrographs of the strained surfaces were taken and magnetic measurements were made. The magnetic readings can be directly converted into percent a'.',e With these measurements the percentage of each phase may be plotted as a function of stress (or strain) and test temperature. It was found that up to 15 pct E phase forms upon stressing the AISI 304L alloy at low temperatures. The E percentage increases abruptly after the alloy yields, but then decreases gradually at higher stresses. The rapid increase in e at 76°K is associated with an "easy-glide" portion of the stress-strain curve. The total amount of a' + .G is suppressed below 76°K at a constant stress or strain. The yield strength decreases down to 76°K but increases rapidly below 20°K. EXPERIMENTAL PROCEDURE Tensile test specimens were cut parallel to the rolling direction from 0.1-in.-thick sheet. Continuous stress vs strain recordings were obtained at each test temperature (300°, 76o, 20°, and 4°K) using equipment and methods described elsewhere.' The specimens which were used in the X-ray analysis were stressed to successive increments of strain at each temperature, analyzed at room temperature, then restressed at the test temperature. This procedure was repeated until approximately ten X-ray analyses had been performed with approximately 1.0 pct strain increments. The specimens had a reduced section 1 in. long, 1.2 in. wide, and 0.1 in. thick. They were electro polished prior to testing and after each strain increment. Table I lists the chemical composition, grain size, and hardness for the alloy which was used. This is the same alloy for which extensive mechanical-property tests3 and morphological studies of the spontaneous transformations' have previously been made. For the low-temperature tests (76o and 4°K) below the Ms temperature the specimens were initially cooled to the test temperature, held for 1/2 hr, then warmed and X-rayed at room temperature. The results are listed in Table 11. From earlier work8 it was known that additional transformation on the second cycle would be considerably less (-0.1 pct

Jan 1, 1964

By J. B. Dilworth

In estimating the investment-value of a mining-property or plant, the value of which decreases with operation, it is often necessary to know the sum which must be set aside periodically from earnings either to renew the plant at the end of its life, or to return the capital involved when the earningpower of the investment has ceased. In such cases it is manifestly incorrect simply to divide the total amount to be retired by the 'number of periods (usually years) during which the investment shall be active, as the sums periodically withdrawn have a certain interest-earning power varying with the length of time they are held and with the opportunities afforded for their investment. But though the interest may be considered to accumulate regularly year by year, yet the rules and tables for compouiid interest do not apply, owing to the addition of a fixed amount of new money to the total at the beginning of each period. Briefly stated, the problem of sinking-funds is, to find the amount of money which must be periodically set aside at a certain rate of interest, regularly compounded, to yield a certain sum in a given length of time. In most practical cases the interest is compounded and the fresh amount added at the same time—usually once a year—and on this basis the problem may be solved as follows : Let S = total amount to be retired, Let T = interest rate : R = 1 + r, Let n = life of tlie sinking-fund or the amortization-period, Let L = the sum set aside at the end of each year. Then the amouilt of the sinking-fund at the end of first year is 2, which at the end of n years will have illcreased by compound interest to IRn-l. Similarly, another amount, x, will be set aside at the end of second year, which will in turn increase

Jan 1, 1911

By H. C. Theuerer

GeC14 may be purified by extraction with HCI and chlorine. The process is as effective for the removal of AsCI:, as the more cumbersome distillation methods usually used for this purpose. GERMANIUM for semiconductor use contains impurities at levels no higher than a few parts in ten million. Material of this quality is obtained from highly purified GeC1, by hydrolysis to the oxide and reduction of the oxide in hydrogen. When purifying GeCl,, AsC1, is the most difficult impurity to remove. This is usually accomplished by multiple distillation procedures.1-3 AsC1, may also be removed from GeC1, by extraction with HC1.1-4 Reducing the arsenic to low concentrations is not practicable, however, because of the large number of extractions needed. This paper discusses a new method for the removal of arsenic from GeC1, by extraction with HC1 and chlorine. The method is rapid, leads to little loss of germanium and is at least as efficient as the distillation procedures currently being used. Theory of Extraction Procedures In the simple extraction of GeC1, with HC1, the following reaction occurs ASCl8G8C1 D AsCl3rc1 at equilibrium CA/Cn= K, where K is the distribution coefficient, and C, and C,, are the molar concentrations of AsC13 in HC1 and GeCl,, respectively. The materials balance equation for this reaction is VACA + vncn = VnC,, where V, and Vn are the volumes of HC1 and GeCl4, respectively, and C, is the initial concentration of AsC13 in GeC1,. From this it can be shown that for multiple extractions where C,, is the concentration of AsC13 in GeC14 after n extractions, and r is the ratio of V, to V,,. It is assumed that r is maintained constant, that equilibrium is established during each extraction, and that K is independent of the AsCl3 concentration. By saturating the system with chlorine, the following reaction occurs in the aqueous phase AsCl3 + 4H2O + Cl2 D H5AsO4 + 5HC1 at equilibrium K' = ------------ ai - a4 h2u - aet2 where a is the activity of the various components. The effect of this reaction is to reduce the concentration of the AsC1, in the aqueous layer and, therefore, to promote further extraction of this component from the GeC1, layer. If the arsenic acid remains entirely in the aqueous phase, the net effect of this reaction is to promote the removal of arsenic from the GeC11. The materials balance equation for extraction with HC1 and chlorine with the foregoing reaction is, then, VaCC + VACA + VACn = VnCo where C,. is the molar concentration of H3AsO, in the HC1. With the added assumptions that the activities of AsC13 and H8ASO4 in the aqueous phase are equal to their molar concentrations, it can be shown that for n extractions Cn/Cu = (1/rkK + rK + 1) n where k - K1 a4h2o - acl2/aoncl. It can be seen by comparing Eqs. 1 and 2 that if k is large, the removal of AsC1, by HC1 extraction will be greatly improved by the addition of chlorine. Dilution of the HCI used in the extraction with chlorine would also favor the separation. This, however, would increase the loss of GeCl,, which is undesirable. Experimental Procedure Germanium prepared from oxide of semiconductor purity is n-type with resistivities greater than one ohm-cm. The resistivity is controlled by the donor concentration, which is —lo-: mol pct. Germanium prepared from material with added arsenic will have lower resistivity commensurate with the arsenic concentration. With such material, at arsenic concentrations above 10-1 mol pct the resistivity is controlled by the added arsenic, and effects due to other impurities initially in the oxide are negligible. In this investigation GeO, of semiconductor purity was converted to GeCl,, and -0.01 mol pct As was added. This material was used for the extraction experiments and the purification attained determined by a comparison of the resistivity data for samples of germanium prepared from the initial and purified GeC1,. A method for calculating the arsenic concentration from the resistivity data is discussed later. The details of the experimental procedures used are as follows: Two hundred and thirty cu cm GeC1, were prepared by the solution of GeO, in HC1, followed by

Jan 1, 1957

By M. E. Kukura, L. G. Stevens

As described in a previous presentation and in various patents, the Minerals Sciences Div. of UOP, Inc., has developed a modified reduction roast ammonia leach process for nickel laterites. This process gave considerable improvement in extraction over the conventional Caron approach as practiced in Cuba, Australia, and the Philippines. This greatly improved response was obtained with a wide variety of ores. This paper describes the pilot plant flowsheet and reviews the design features unique to the UOP process. Operating results from pilot plant campaigns are compared with bench scale results. Operating problems and their solutions are also discussed.

Jan 1, 1976

COLORADO SCHOOL OF MINES On February 21, 1918, the students of the Colorado School of Mines who are members or have applied for membership in the Institute re-organized the "Scientific Society of The Colorado School of Mines,? which has for its .purpose the study and discussion of mining problems. Its meetings will be held on the first and third Wednesdays of each month, in Guggenheim Hall. Following are the officers R. W. GIBSON, President, W. A. CONLEY, Vice-president, F. L. SERVISS, Sec'y.-Treas. At present there are 62 members, seven of whom are Faculty members. F. L. SERVISS, Secretary.

Jan 5, 1918

By W. Laird

For years, the coal industry has been confronted with face ventilation problems, ignitions, dust, and their effect on productivity. To improve face ventilation, minimize face ignitions, and control dust in the face areas, studies have been conducted over the past 30 odd years by coal companies, federal government research programs and others. These studies included brattice curtains, water spray nozzles, water pressures, highly efficient water filtration systems, auxiliary fans, differ fans, various dust collection systems and the recently developed "Spray Fan" ventilation system. This system consists of spray banks strategically placed on continuous miners to ventilate immediate face area.

Jan 1, 1984

By AIME AIME

CLYDE WILLIAMS, after graduating from the University of Utah as a chemical engineer, worked for a time in western mills and smelters. He then joined the U. S. Bureau of Mines and during the World War studied Ordnance Department and Navy problems on ferroalloys and alloy steels at the Cornell University laboratories. Later, as superintendent of the Northwest Experiment Station of the Bureau, he was active in electric furnace and ore reduction work. Clyde then went to South America and surveyed the iron and fuel resources of the Argentine. Returning, he became chief metallurgist of the Columbia Steel Corp., of

Jan 1, 1936

By C. A. Stewart

PAGE. I. Introduction............ 241 II. Location. TopoGRaphy. and History....... 243 III. DescRiption of the Rocks......... 245 1. Altered Sediments.......... 245 2. Alaskite........... 246 3. Alaskite.Porphyry.....255 4. Quartz Dikes........... 257 5. Biotite.Granite.......... 256 6. Quartz.Porphyryl......... 260 7. Andesite........... 262 8. Miscellaneous Dikes......... 263 IV. Age oF the Rocks and Comparison with other Localities.. 263 V. AlteRation............ 265 1. Sericitization........... 265 2. Silicification........... 266 VI. StRuctuRes........267 1. Dip of the Limestone......... 267 2. Faulting........... 267 VII. Contact - metamorhism,.......... 269 1. Endomorphism.......... 269 2. Exomorphism......... 271 Recrystallization and Loss of Color...... 271 New ,Minerals.......... 272 Addition of Material........ 274 Volume.Changes.... 276 Locus of Metamorhism........ 277 Method of Precipitation.........278 VIII. ORe-Deposits............ 278 1. Contact-Metamorphic Copper.Ores,..... 279 General..........279 Shape and Distribution........ 279 Minerals........... 281 Secondary Enrichment........ 282 2. Disseminated Copper.Ores........ 283 3. Origin of the Copper.Orcs........ 284 4. Lead-Silver Ores.......... 287 IX. Bibliography............ 288

Jan 1, 1913

By L. S. Austin

I. Introduction............ 431 II. Organization............ 432 III. Production............ 434 IV. Transportation............ 435 V. Sampling..........436 VI. Concentration............ 440 VII. Blast-Furnace Plant........... 442 1. Construction........... 442 2. Operation............ 450 VIII. Advantages of Large Furnaces........ 455 1. Saving in Fuel........... 455 2. Saving in Jacket.Water..... 455 3. Quick and Large Discharge of Matte and Slag... 455 4. Decrease of Incrustation... 456 5. Elasticity of Operation..457 6. Large Flow Through Fore.Hearths...4. 57 7. Alterations Without Interruption..458 8. Variations in the Composition of Slag....458 9. Less Labor-Cost.......... 458 10. Less Initial Cost.......... 460 IX. Briquetting.Plant........... 460 X. Roasting-Plant............ 462 1. Kilns............ 462 2. Reverberatory Furnaces...468 XI. Converter-Plant........... 474 1. Construction ..........474 2. Operation.......... 476 XII. Flues and Stacks........... 478 XIII. Arsenic-Plant............ 480 XIV. Coke-Washing Plant.... 452 XV. Slime.Ponds ........... 483 XVI. Brick-Plant............ 484 I. Introduction. The Washoe plant; in Anaconda. Mont., together with the local street-railroad, ranches. a foundry and machine-shop. A

Jan 1, 1907