Search Documents

By R. W. Gurry

Thermodynamic calculations indicate that boron is a better deoxidizer than silicon but probably is not quite as effective as aluminum. Boron should, therefore, be readily oxidized out of the open-hearth bath, which implies that it is not recovered in significant concentration from any scrap charged; also that, if added in the ladle, it tends to oxidize out during teeming unless protected by the presence of a better deoxidizing agent. These conclusions do not apply to liquid cast iron, in which the oxygen content is much lower than in liquid steel. The possibility of conserving certain strategic alloying elements widely used in steelmaking, notably manganese, chromium and molybdenum, by the use of boron, which in small concentration appears to be extraordinarily effective in promoting hardenability, raises a question as to what extent any boron present in the scrap charged into the open hearth is oxidized out during melting and subsequent refining. This question is significant because the optimum concentration of boron in the finished steel, which is fairly critical, would be very difficult to attain if the boron in the charge were largely retained in the metal. Moreover, unless boron is substantially eliminated in the open-hearth process its use on a large scale would eventually make it impossible to produce boron-free steel except by restricting the charge to virgin material. There is at present, unfortunately, virtually no satisfactory direct evidence to provide an answer to this question; but there are indications from practice that boron is oxidized out in the open hearth in the production of medium or low-carbon steel, although it may be retained if the carbon content remains fairly high; that is, if the oxygen is kept fairly low. In the absence of direct data, it is necessary to rely upon the indications of indirect evidence, the best approach now available being a thermodynamic calculation of the deoxidizing power of boron in liquid steel by the general method used so successfully by Chipman1 in his study of the reactions in the open-hearth process. The thermal data for boron, upon which such a calculation must be based, are reasonably satisfactory; the only quantities not directly determined are the entropy of melting of boron, the activity coefficient of boron in liquid steel, and the activity coefficient of B2O3in an open-hearth slag; but these values may be estimated with ample accuracy. The results of this calculation, which is presented later, are given in Table I, together with corresponding data for other deoxidizing elements. This table shows the calculated residual content of oxygen in equilibrium with different residual concentrations of the deoxidizer in the metal;

Jan 1, 1944

By R. W. Gurry

Thermodynamic calculations indicate that boron is a better deoxidizer than silicon but probably is not quite as effective as aluminum. Boron should, therefore, be readily oxidized out of the open-hearth bath, which implies that it is not recovered in significant concentration from any scrap charged; also that, if added in the ladle, it tends to oxidize out during teeming unless protected by the presence of a better deoxidizing agent. These conclusions do not apply to liquid cast iron, in which the oxygen content is much lower than in liquid steel. The possibility of conserving certain strategic alloying elements widely used in steelmaking, notably manganese, chromium and molybdenum, by the use of boron, which in small concentration appears to be extraordinarily effective in promoting hardenability, raises a question as to what extent any boron present in the scrap charged into the open hearth is oxidized out during melting and subsequent refining. This question is significant because the optimum concentration of boron in the finished steel, which is fairly critical, would be very difficult to attain if the boron in the charge were largely retained in the metal. Moreover, unless boron is substantially eliminated in the open-hearth process its use on a large scale would eventually make it impossible to produce boron-free steel except by restricting the charge to virgin material. There is at present, unfortunately, virtually no satisfactory direct evidence to provide an answer to this question; but there are indications from practice that boron is oxidized out in the open hearth in the production of medium or low-carbon steel, although it may be retained if the carbon content remains fairly high; that is, if the oxygen is kept fairly low. In the absence of direct data, it is necessary to rely upon the indications of indirect evidence, the best approach now available being a thermodynamic calculation of the deoxidizing power of boron in liquid steel by the general method used so successfully by Chipman1 in his study of the reactions in the open-hearth process. The thermal data for boron, upon which such a calculation must be based, are reasonably satisfactory; the only quantities not directly determined are the entropy of melting of boron, the activity coefficient of boron in liquid steel, and the activity coefficient of B2O3in an open-hearth slag; but these values may be estimated with ample accuracy. The results of this calculation, which is presented later, are given in Table I, together with corresponding data for other deoxidizing elements. This table shows the calculated residual content of oxygen in equilibrium with different residual concentrations of the deoxidizer in the metal;

Jan 1, 1944

By Harold Roast

THE object of this investigation was to compare the arsenical antimony-lead alloy with some of the regular bearing-metal alloys. With this end in view, the following tests were made: 1. Chemical analyses to show the composition. 2. Thermal analyses. 3. Macroscopic examination of fractures. 4. Microscopic examination. 5. Tensile tests. 6. Crushing tests. 7. Scleroscope tests. 8. Brinell tests, at temperatures from 80° to 400° F. Tests 3 to 8 were conducted on both sand-cast and chill-cast specimens. For the purposes of this paper the alloys have been numbered from 1 to 6; their composition is as follows: LEAD, ANTIMONY, TIN, COPPER, ARSENIC, NUMBER PER CENT. PER CENT. PER CENT. PER CENT. PER CENT. 1 82.64 12.95 4.40 0.01 none 2 27.54 9.94 59.87 2.65 none 3 77.65 20.75 none 0.13 1.47 4 82.95 16.85 none 0.20 none 5 83.78 15.35 none 0.05 0.82 6 0.15 7.87 84.13 7.85 none The analysis, in the case of the antimony, was made by solution in sulfuric acid and titrated with permanganate. For tin, the ferric-chloride method was used; for copper, the alkaline separations, and the thiocyanate methods; for arsenic, volatilization of arsenic and titration with iodine. The lead, with the exception of alloy 6, was taken by difference.

Jan 2, 1922

By Jean Herenguel

THE published work of Lacombe and Beaujard' has demonstrated the interesting application of etch figures to the determination of crystal orientations in aluminum by a purely micrographic method. The geometry of these figures leaves no ambiguity and the method has the added advantage of being applicable to very small crystal units. These authors applied the technique to the study of high purity aluminum, and it has now been adopted buy Heren-guel and his collaborators to various researches on commercial aluminum, containing up to 1 pct Fe and Si. This must modify the opinion point,ed out by

Jan 1, 1953

By J. B. Caine

THE investigation outlined in this paper was carried on at the plant of the Sawbrook Steel Castings Co., Lockland, Ohio. EFFECT OF TEMPERATURE In the study of the effect of temperature, heats were made with the Sawbrook company's standard practice, using multiple slags, the only difference' being that the heats were tapped at two temperatures; one group between 2960° and 3040°F and the other group between 3200° and 3250°F. Slags were weighed throughout the heat at each slag change and after the heat was poured. Only the significant slag weights, those of the total slag and the finishing slag, have been reported.

Jan 1, 1947

By John W. Cloud

The delivery of blows upon roadway structures by the locomotive engine at high speed, althongh long recognized, has, perhaps, not been as generally understood in severity, relation to speed, and cause as is desirable in matters of such importance. Some points of explanation, with illustrative disgrams, are, therefore, submitted to your attention, preparatory to a note 011 " Steel for Bridges," also submitted. In order that a locomotive may run at high rates of speed with-

Jan 1, 1881

By R. V. Lundquist

Leaching manganese-bearing materials with NaOH to remove caustic-soluble silica has been demonstrated as a method for up- grading manganese. Those materials containing opaline varieties of silica respond most readily. Spent leach liquors are regenerated by treatment with lime to precipitate calcium silicate and to reactivate the NaOH for leaching.

Jan 4, 1953

Consolidation Coal Co. is solving the abrasion problem and cutting maintenance costs at its Georgetown preparation plant by using ceramic alumina tiles from The Carborundum Co. The Georgetown complex handles the output of four deep mines and three strip mines in the Cadiz, Ohio, area-washing about 73 000 tons (80,000 st) weekly. Plant superintendent Duke Zinko is using wear-resistant Dura-frax® tiles in several applications, replacing wear plates, profile rubber, and other materials he has tried over the years.

Jan 7, 1979

By F. G. Stone

A strain anneal process has been developed for the production of iron tensile test specimens, the gauge length consisting substantially of a single crystal. Since the method has been quite successful and the results of general interest, the process will be described in detail. The essential feature of the method is the continuous, slow increase of furnace temperature during the grain growth annealing treatment. Briefly, the procedure is as follows: I. Heat machined bars to 950°C in vacuum, hold I hr, furnace cool. 2. Strain to 3.5-3.8 pct elongation (axial loading). 3. Anneal, continuously raising furnace temperature from 450 to goo°C at a rate of so0 per day. 4. Hold at 900°C for 100 hr, furnace cool. Tensile test bars with a 1/4- X I-in. gauge section have been machined from 35 in. Armco iron plate and from 3/8 in. rounds of Puron, a high purity laboratory iron. The axes of the test bars were parallel to the rolling direction. During the machining operation the bars were polished in the lathe with No. 600 emery paper, and this polished surface proved satisfactory for subsequent macrographic examination. A micrographic examination of the materials showed that both were high in FeO inclusions, those of the Puron being smaller but much more numerous. An initial vacuum anneal of I hr at 950°C followed by furnace cooling resulted in a ferritic grain size of ASTM No. 3 for Armco and No. I for Puron. Special heat treatments which reversed these initial grain sizes produced no marked improvement in single crystal production after subsequent treatments. The strain for subsequent grain growth was determined by measuring the decrease in diameter of the tensile bar during elongation. The change in diameter could be measured with a micrometer to +0.0001 in., corresponding to an accuracy of 0.08 pct for the elongation. The accuracy of the diameter measurement is also dependent on grain size because of surface roughening during elongation, and for this reason, a No. 3 grain size is preferable. Optimum grain growth was obtained for strains between 3.5 and 3.8 pct elongation. Once this critical range had been cstablished, all tests were held within it, and thus only meager data were obtained on grain growth following strains outside this range. In general, grain size decreased with increasing strain to about 5.5 pct elongation. Grain growth was occasionally ohserved with less than 3.5 pct elongation although this may have been the result of error in measurement. The program control device for the grain growth anneal consisted of a I rpm motor and worm gear drive, operating the dial shaft of a pyrometer controller through a pulley. Dial speeds of 33 and 50°C per day were tried, but the results at the slower speed were not sufficiently better to warrant the increased furnace time. The furnace tube was evacuated at intervals during the run and kept sealed the remainder of the time. When the controller reached 900°C, it was stopped and the temperature held for 100 hr. This eliminated most of the numerous minute crystallites of about 0.5 mm dimension usually visible on the etched surface of the single crystal. Since recrystallization occurs at the A3 point, the top temperature of 900°C provided a 10"

Jan 1, 1949

By P. Schwarzkopf, J. H. Brophy

A modification of the Mendenhall wedge blackbody1 has been used to determine solidus temperatures and to anneal alloys in the tantalum-rhenium binary system. The technique has proven to be simple and accurate with modest power requirements. For temperatures up to 2800° C a piece of 10-mil tantalum sheet was folded double and formed as shown in Fig. 1. The middle of the resulting ribbon filament was a cylindrical-shaped crucible with less than a 1/8-in. opening. After inserting a specimen in the cavity, the filament was clamped between molybdenum electrodes in a high vacuum chamber. A representative filament 2 in. long and % in. deep was heated to 2800°C with a current of 700 amp at 4 v. The specimen temperature was determined by sighting into the cavity with a Leeds and Northrup optical pyrometer. The twisted filament shape was necessary to avoid serious geometric changes during thermal expansion. For temperatures between 2800" and 3000°C a 4-mil tungsten filament was employed. To facilitate fabrication it was warm-folded, and a twisted segment of 10-mil tantalum was used to support one end to absorb thermal expansion. This element assembly required about 700 amp at 10 v to reach 3000°C. Two geometric modifications of the filament were helpful for solidus temperature determinations. A shallow chamber, with depth to opening ratio of 3 to 1, permitted direct observation of the specimen through the optical pyrometer. The fact that the specimen was visible permitted the melting point to be determined when sharp features on the specimen surface became rounded; it also indicated that blackbody conditions did not prevail. By standardizing against the melting point of molybdenum, the observed melting temperature was corrected by the following form of Wien's Law: in which T is the true temperature, To is the observed temperature, and K is a constant characteristic of the filament geometry and determined experimentally for the molybdenum standard. The resulting corrected melting point for each alloy served as a reference temperature for the second more precise filament geometry. With a 6 to 1 depth to opening ratio, the specimen was indistinguishable from the filament interior, indicating good blackbody conditions. Using this technique, a series of specimens was isothermally treated at temperatures above and below the corrected direct reading. Incipient melting was detected by visual or micrographic examination of the specimen after cooling. This procedure was checked with specimens of pure chromium, molybdenum, and tantalum. Table I represents the values obtained, together with the solidus temperatures in the tantalum-rhenium binary system determined by the same technique. The alloy specimens were approximately 1/8 in. in diam. They were pieces of 10-g buttons melted four times in a nonconsumable tungsten electrode arc furnace on a water cooled copper hearth in 2/3 atmos of titanium gettered helium. Several sources of error are possible in such temperature measurements. Within the accuracy of the pyrometer no gradients were detectable near the specimen, and element distortion was virtually eliminated by twisting the tantalum. Compensation was made for the 1/8-in. sight glass by inserting several identical thicknesses and extrapolating to zero thickness. As a result an additional 10°C correction was added to all observations in the temperature range of 2500" to 3000°C. The principal source of error was then in the operation of the

Jan 1, 1961

By R. E. Robbins, H. R. Brager

THIS note describes an unusual result obtained in an electron microscope investigation of cavities produced in commercial type 304 stainless steel irradiated in a thermal reactor (ETR) at 290°C to a high neutron flu-ence, 6 x loz1 n per sq cm. The analysis of the steel used is given in Table I. The unusual result is that the calculated quantity of helium gas produced by transmutation during the irradiation, 12 ppm, is less than one-tenth the amount of gas necessary to balance the surface tension of the observed cavities produced in the steel during ETR irradiation. Therefore, the cavities would be expected to behave like voids; however, they behave like "gas filled" bubbles. The maximum quantity of helium produced in the steel by B" transmutation was 8 ppm. In addition, the amount of helium formed by (n, (1) fast neutron reactions with the major alloy constituents and nitrogen was calculated to be 4 ppm based on the tabulated differential or effective fission-averaged cross sections of elements in type 304 stainless steel irradiated in typical thermal reactors.', In previous investigations concerning commercial austenitic stainless steel irradiated in a thermal reactor, the amount of helium gas calculated to be produced by transmutation has always been significantly greater than the amount calculated on the basis that the bubbles were gas filled, PPs= 2y/R. The balance of the gas was assumed to be in bubbles smaller than could be detected on the electron micrographs. Accordingly, the bubbles were attributed to helium produced from transmutation of impurity boron by thermal neutrons. These bubbles were not uniformly dispersed in the matrix but were located principally at grain boundaries, or were radially positioned around a few precipitates located in the matrix and at the grain bundaries., 4 Voids have also been observed in austenitic stainless steel irradiated at high temperature to high neutron fluences in the EBR-I1 and Dounreay Fast Reactors. The voids were uniformly distributed throughout the matrix. The amounts of helium gas produced by transmutation during these irradiations were less than one-tenth the amounts needed to balance the surface tension of the voids formed by the fast reactor irradiation. The fast reactor results are quite analogous to those reported here for the ETR irradiated steel. Electron microscope examination of the fast reactor irradiated material after a 1 hr postirradiation annealing at 900°C disclosed that essentially all the voids had been eliminated. The authors stated that the voids had developed due to the high concentration of vacancies produced during irradiatin., 6, ' The microstructure of the ETR irradiated material as-tested at 75O°C, Fig. 1, contained about 2 X lot5 cavities per cm3 with an average diameter of 110A. With the Van der Waals b correction and y = 1500 ergs per cm2, 300 ppm He would balance the surface tension of the observed cavities. Stereoscopic examination of the electron micrographs showed that the cavities were neither preferentially located near the grain boundaries nor highly concentrated at specific regions or precipitates. The cavities were nearly uniformly distributed throughout the matrix, on dislocations and at grain boundaries. These observations imply that the cavities were not the sole results of B'O

Jan 1, 1969

By O. J. C. Runnalls, L. M. Pidgeon

Some observations on the kinetics of the iodide process are reported. The deposition rate is geometry-sensitive in a system containing a finely divided titanium charge. Further, results indicate that the iodine diffusion rate influences the velocity of the process. The nonvolatile iodide, Til,, forms in the hot filament zone, thus removing iodine from the cycle. TITANIUM metal of 99.9 pct purity may be prepared using a refining technique originated by Van Arkel and de Boer.' The purity of this metal, commonly called iodide titanium, exceeds that produced by any known process. In a recent application, the method was employed by Gonser et al.² to prepare titanium rods up to 2 to 3 cm in diam. In the Van Arkel-de Boer system, the relative influence of the fundamental mechanisms: l—production of titanium iodides, 2—gaseous countercurrent diffusion, and 3—decomposition, on the deposition rate have not been clearly established. Blocher and Campbell" have indicated that the controlling step in the process under practical conditions of operation may be the reaction rate of iodine with the crude metal. Fast' reported that crude titanium metal reacted with iodine rapidly, even at room temperature, in his apparatus. Little has been reported on the effect of gaseous diffusion or decomposition on the deposition rate. It is these aspects of the process about which this investigation is centered. An attempt has been made to separate these latter effects from those due to the formation of the iodides at the crude metal surface by a division of the experimental program. Reaction of Iodine with Titanium Apparatus: In the investigation of gas-metal reactions of this type, the chemical reactivity of the halogen and halide vapors dictates the use of all-glass apparatus. In such a system standard techniques for measuring reaction rates are difficult to employ. Here, a simple apparatus was devised (Fig. 1) so that some indication of the reactivity of titanium powder with iodine vapor could be obtained. A stream of iodine gas was evolved from a bulb of controlled temperature and passed over a sample of titanium powder heated in a horizontal tube furnace. The product of the reaction, TiI4, volatilized and was condensed outside the furnace in a series of four glass bulbs, each cooled to room temperature in turn. Preliminary experiments indicated that distillation was retarded in a sealed evacuated system due to a pressure build-up in the condensing end of the apparatus. Hence, the system was pumped continuously using a mechanical pump and two oil diffusion pumps in series, through a liquid air trap. The iodine bulb was made large and a capillary restriction was inserted between the titanium bulb and the condensers so that the iodine pressure over the metal would approach the equilibrium pressure over solid iodine crystals. The effect of this restriction on the evaporation rate of TiI4, was determined separately. The iodine bulb was heated in an oil bath controlled to ±2°C. The titanium bulb temperature was automatically controlled to ±5°C. Procedure: About 200 mg of —30 mesh titanium powder, weighed to 0.1 mg, was placed in the reaction bulb after part B had been joined to part A. The powder was tapped into a long (5 cm) shallow mass along the bottom of the tube. Two chromel-alumel thermocouples were inserted into the magnesium radiator which was clamped to the reaction

Jan 1, 1953

By Peter J. Huck, Madan M. Singh

IIT Research Institute has investigated the potential of high pressure water jets for rapid rock excavation. During this study, an attempt was made to correlate the extent of breakage effected to the mechanical properties of rocks. Six rock types were used in these experiments and nine properties were determined for each rock variety. A regression equation using the two most significant rock properties and one jet parameter (pressure) was established. Although tests were conducted to specific pressures of 35, no minimum in the specific energy consumption was noted.

Jan 1, 1971

By Sir John Cadman

IN THE changed circumstances which now confront the world, an international open-door policy is the only way to keep pace with the world's demand for oil. You may rest assured that as far as the British Empire is concerned, American capital for the develop-ment of oil resources is welcome, and little obstruction will be found in the way to permit the use of foreign capital in the group of countries which constitute the British Empire. In the war days we worked in close cooperation and harmony, but in disbandment of the Petroleum War Service Committee, when the war ended, I feel that it left its task unfinished. In the wake of war there appeared a ghost of war-time conditions in the form of belief that Great Britain was straining to corner the petroleum resources of the world. I am certain that if the war-service committee had continued its work in the period of reconstruction the real story would be known and this sinister ghost would have long since vanished before the truth.

Jan 2, 1922

Very little coal was produced in Texas in the period considered and nearly all of that was used locally. All data are shown in Table 81. [ ]

Jan 1, 1942

By G. A. Vissac

O. R. LYONS *—I wish to thank Mr. Vissac for his compliment. I hope that his paper is not only well received, but that it will serve to bring forth more papers on the subject of thermal drying. One of the primary purposes of the work performed by Battelle for Bituminous Coal Research in investigating the thermal drying of coal was to stimulate other investigators and to get them to contribute their knowledge in the form of papers such as this one. We at Battelle and the personnel of Bituminous Coal Research are very gratified that Mr. Vissac and other persons have responded in this matter of the thermal drying of coal. I wish to state that I think that Mr. Vissac's paper is a very clear and easily understood description of a method of calculating the design requirements for a screen type drier, and I think that it would be exceedingly valuable to operators and to those who intend to purchase any type of thermal drier and use it in the future, if the manufacturers or operators who have such information for other types of driers would provide the same type of information for the other makes of driers now on the market. 1 also wish to point out—an idea that is new to me, and I know is new to most of the operators of driers in the United States-—the idea of recovering the heat that is normally lost in the coal and in the exhaust gases. This heat is not being recovered at most (of the thermal drying operations in the United States, and the possibility of recovering it should be called to the attention of every single one of those operators. I know many of them have never given any thought to the matter, but they will be interested once they realize the ease with which it could be done and the savings that could be realized. I also wish to compliment Mr. Vissac for presenting the method of analysis that he uses to determine the difficulty of drying any particular coal. It is a very simple method, and yet it seems to me that it should be a very effective, very efficient method for determining the difficulty of drying for his particular problems. C. Y. HEINER*—I do not know that I can add anything very illuminating to what Mr. Vissac has said. I think anything that Mr. Vissac said in regard to coal drying is a contribution because, to my personal knowledge, he has studied the matter carefully for many years and made many valuable contributions. I am not too familiar with coal drying problems in the east, but I know in the west we have not made enough coal drying studies. I think coal operators too often just take the coal as it is and make more or less the best of it. There are relatively few washing plants in the west now, and so the problem has not come to the front as much as it probably will in the future. In this connection, it seems to me that this matter of drying the raw coal, as Mr. Vissac brings up, is an extremely important one. We have not a continuous miner ourselves, yet, but we expect to get some this year, and we think the percentage of fine coal-—that is, minus 3/16 in.—will double. We have about 20 pct minus 3/16 in. in the 8 in. by 0 size now, and we think we will likely have 40 pct, which will have a surface moisture of the order of 8 pct. To wash it satisfactorily, we will have to dry the raw coal first in order to screen it, and after that, I suppose, there will have to be dry cleaning of some sort. We have not really used dry cleaning on fines in the west yet to my knowledge, but it is a matter that has to be faced by the industry, and I am very hopeful that Mr. Vissac's study will assist us in that connection. W. L. McMORRIS*-In my company we are preparing largely metallurgical coal for a great number of byproduct coke plants. The most outstanding thing to me about the requirements of moisture in the finished product is that there is a different requirement for almost every coke plant. Each operator has a different set of factors on which he establishes his coking costs where they involve moisture. For our corporation operations in Birmingham, my company does not produce the coal, but in Birmingham they are getting away with moistures very much higher than our plant at Clairton, Pa., would tolerate. The moisture that we have to produce for the plants along the lakefront where they are subject to much more severe weather is something else again. We have not tackled heat drying, primarily because our customers do not know what heat drying will do to the coking characteristics of the coal. If the temperature of drying can be held down

Jan 1, 1950

By Richard R. Zupp, David A. Stevenson

An experimental method to determine the carbon activity in various solid solutions was developed. Samples of the solid solutions and an Fe-C reference sample were equilibrated with respect to carbon content by annealing them in a Hz-CHI gas mixture in a closed cell. The carbon content of each sample was determined, and the carbon activity was obtained from the carbon content of' the reference sample and well-established data for the dependence of the carbon activity on the carbon content in Fe-C alloys. The influence of vanadium on the activity of carbon in austenitic Fe-C-V alloys at 1000°C was determined by this technique. A general semiempirical correlation was developed to describe the dependence of the activity coefficient of- carbon on the composition of ternary austenitic iron-base alloys containing interstitial carbon and a substitutional solute. The correlation is particularly useful in predicting the partitioning of- carbon between various alloys. THE influence of substitutional solutes on the activity of interstitial solutes in metallic solid solutions is important in the theory of alloy phases. Solid solutions of particular interest are the fcc austenite phases of ternary Fe-C-Z systems, in which carbon is the interstitial solute and Z represents any substitutional solute. Carbon-activity data are also needed in these solid solutions to solve practical problems; the quantitative treatment of diffusion-controlled transformations' is an examvle. Experimental information is available for ternary austenitic solid solutions containing Mn,2 Si,2 and A16 as the substitutional solute. Because qualitative preliminary studies indicated that vanadium appreciably decreases the carbon activity,14 the present investigation was undertaken to determine the influence of vanadium on the activity of carbon in austenite. Although Flender and ever" measured carbon activity over a range of compositions in the Fe-C-V system, they were primarily interested in determining phase boundaries in the ternary system, so most of their measurements were outside the composition range for stability of single-phase austenite. Petrova and Shvartsman' also made limited measurements of the carbon activity in Fe-C-V alloys. The dependence of the carbon activity on the carbon content of an alloy may be determined by passing COCOz or H2-CH4 gas mixtures of carefully measured composition over the alloys, determining their equilibrium carbon content, and utilizing the relevant equilibrium relationships. smith16 used this technique with both CO-COZ and HZ-CH4 gas mixtures to determine the dependence of carbon activity on carbon content in pure Fe-C alloys. His data, which are in good agreement with those of some previous and subsequent investigators,6'17 but not with those of others,lfl'ao are usually considered to be the most reliable. Although the same method can be applied to Fe-C-Z alloys, it is difficult experimentally, because the appropriate gas mixtures are almost pure CO or Hz. A simpler technique is to simultaneously equilibrate the Fe-C-Z alloys and pure Fe-C alloys with the gas mixtures, and then use Smith's data to determine the carbon activity in the pure Fe-C alloy. A number of investigators have employed this technique. others Have used the partitioning of carbon at the interface of a diffusion couple prepared from an Fe-C alloy and a Fe-C-Z alloy. In the present study, a closed-cell method was developed by which carbon was selectively transferred via a gas medium between pure Fe-C alloys and Fe-C-V alloys which were not in physical contact. A similar method was developed independently by Heckler and winchel14 and used to study the Fe-C-Ni system. EXPERIMENTAL METHOD A schematic diagram of the experimental arrangement is shown in Fig. 1. In a typical experiment, a 5-g Fe-C sample was placed in one compartment of a quartz cell, and a 5-g Fe-V sample was placed in each of the other compartments. The cell was evacuated, outgassed, backfilled with approximately 125 Torr of hydrogen, and sealed. After being placed in a fur-

Jan 1, 1967

By Donald B. Evans, Robert D. Pehlke

The solubility of nitrogen in liquid Fe-B alloys has been measured up to the solubility limit for the formation of boron nitride. The activity coefficient of nitrogen increases with increasing boron content in the range 0 to 7 wt pct B. From experimen -tal data, values have been calculated for the B-N interaction parameter e3 at temperatures in the range 1550" to 1750°C. A value of 0.038 has been estimated for the boron self-interaction parameter eg at 1550°C. The standard free energy of decomposition of boron nitride into the elements dissolved in liquid iron has been determined to be: ?F° = 45,900 -21.25T in the range from 1550° to 1750°C. The nitride is assumed to be of composition BN. BORON nitride has an unusual combination of properties which make it appear attractive in a wide range of engineering applications. Some of its more important and most recent applications are in the nuclear area, particularly in connection with the liquid-metal cooled reactor concept now receiving considerable emphasis. Boron nitride has a high degree of stability at elevated temperatures. It also has excellent ma-chinability and the ease with which its crystals deform suggests applications as a lubricant. These properties stem from a hexagonal layer-type structure similar to the structure of graphite. One of its primary uses to date has been for seals in liquid-metal pumping systems. It is also used in nuclear reactors as an insulating layer to separate two solid metals which are not themselves compatible under the conditions of temperature and atmosphere in which they are used. Its inertness to liquid metals has also suggested use as a mold-release agent in casting processes. In addition to its excellent machinability and reported inertness to liquid metals such as iron, silicon, aluminum, copper, and zinc, boron nitride has high thermal conductivity and excellent thermal shock resistance. This combination of properties would make it appear ideal as a refractory crucible material for refining of high-purity liquid metals, for example high-quality steels. However, since it is known that concentrations of boron as low as 50 ppm can have a marked effect on the physical properties of certain steels,' in particular on the creep and stress-rupture properties, an investigation was undertaken to define accurately the chemical equilibrium among boron, nitrogen, and liquid iron in the range of steelmaking temperatures. EXPERIMENTAL PROCEDURE Two experimental approaches to this problem were employed: a Sieverts' method and a quenching method. In the first method, the Sieverts' technique was used to measure the equilibrium nitrogen solubility in liquid Fe-B alloys of 0 to 7 pct B as a function of nitrogen gas pressure over the melt. The solubility limit of the boron nitride phase formed was determined by the point of departure of the nitrogen absorption from Sieverts' Law. This technique has been applied to liquid Fe-Ti alloys by Rao and parlee,' to liquid Fe-A1 alloys by Evans and Pehlke,3 and to solid Fe-V alloys by Fountain and Chipman.4 In the second method a melt of liquid iron was held in a crucible of boron nitride under a known partial pressure of nitrogen gas. After thermodynamic equilibrium was attained, the melt was quenched in a stream of helium and then analyzed by wet-chemical methods for boron and nitrogen. The Sieverts' apparatus used in the first method was essentially of the same design as the one described by Pehlke and Elliott.5 The charge materials were vacuum-melted high-purity iron (Ferro-vac E) supplied by the Crucible Steel Co. and -325 mesh boron powder supplied by Cooper Metallurgical Associates of Cleveland, Ohio. The boron contained less than 0.02 wt pct O, according to supplier's analysis. Recrystallized alumina crucibles were used to contain the melt. Examination of solidified melts showed these crucibles to be satisfactory with no evidence of any reaction or physical penetration of the crucible wall by the melt. The melt temperature was measured by a disappearing filament-type optical pyrometer sighted vertically downward on the melt surface through a 1/4-in.-diam sight hole in the crucible lid. The pyrometer was calibrated against the melting point of pure iron in the same apparatus, taking the emissivity of

Jan 1, 1964

By P. S. Kotva

Dislocation substructures in superalloy matrices of varyzng co)npositions have been studied. In general, it has been found that the alloys can be classified into ''high", ''medium", and "low" stacking fault energy classes based on the type of dislocation substructure observed in the matrix and that the substructure can be correlated to the stacking fault energy. The effect of different types of dislocation substructure and dislocation reactions on the intragranulur precipitation of carbide phases has been studied. In a Ni-Cv-Mo-Fe matrix, precipitation of MC carbides in association with stacking faults has been observed. In most superalloys, solid-solution strengthening and precipitation hardening are the chief mechanisms employed to achieve strength. The latter contribution to strength is usually achieved by the precipitation of / in certain wrought alloys. Insufficient attention has been given to the problem of obtaining strength in su-peralloys by controlling precipitation of carbides on imperfections within the matrix. The present work was undertaken to investigate the dislocation substructure in various superalloy matrices, to study the effect of such substructure on subsequent precipitation of carbides in the matrix, and to investigate whether certain modes of precipitation of carbide phases found in austenitic stainless steels2"4'6 would occur in nickel-base alloy matrices with dislocation substructures of the same type as those found in austenitic steels. 1) EXPERIMENTAL TECHNIQUES Five-pound heats of the various alloy compositions reported here were vacuum-cast. The ingots were given light deformation by rolling to break up the as-cast structure and then homogenized for 24 hr. HASTELLOY alloy X (nominal composition: Ni-2OCr-17Fe-8Mo-0.05C) was homogenized at 2150°F and In-cone1 625 (nominal composition: Ni-20Cr-5Fe-8Mo-3.5Cb-0.05C) was homogenized at 2280°F. Fabrication of 0.004-in. sheet was achieved by cold rolling with intermediate annealing treatments being carried out at the same temperature as those used for homogeniza-tion. Each solution anneal was followed by quenching. The aim of this procedure was to redissolve as much of the primary carbide phase as possible. Samples of the 0.004-in. sheet were cut and encapsulated in quartz capsules and then heat-treated in the tube furnaces. Thin foils were prepared using an ethanol-10 pct perchloric acid bath at 32°F and at a voltage of 22 v. A "window" technique was employed. Observations were made on a JEM-7 electron microscope operating at 100 kv. 2) EXPERIMENTAL RESULTS a) Types of Dislocation Substructure. Fig. 1 shows a schematic correlation between stacking fault energy, SFE, and the type of dislocation substructure observed in various matrices of nickel- and cobalt-base alloys. A precise quantitative determination of stacking fault energy is not implied in the figure but the correlation between stacking fault energy and the type of dislocation substructure obtained allows alloys to be divided into three classes in analogy with the classification employed by Swann and ~uttin~' for binary alloys of copper. Class I alloys are associated with a "high" SFE and show a cellular substructure of dislocations as typified by the micrograph of a thin foil of pure nickel deformed 4 pct at room temperature in Fig. 2. With decreasing SFE the tendency toward cell formation is lessened and dislocations tend to be arranged in coplanar groupings. Examples of this class of alloys with "medium" SFE are provided by the mi-crostructure of solution-heat-treated, quenched, and deformed thin foils of HASTELLOY alloy X, "Waspaloy" (prior to any aging), and Inconel 625. Fig. 3 shows a thin-foil micrograph of an alloy of Inconel 625 composition, solution-heat-treated, quenched, and deformed 5 pct at room temperatures. No evidence of any cell structure can be obtained in materials of "medium" stacking fault energy, Fig. 3, even after severe deformation. The stacking fault energy of the alloy shown in Fig. 3 is, however, not low enough to make the dissociation of dislocations visually obvious. As stacking fault energy decreases further, with successive addition of solute in the matrix, there is an increased tendency toward dissociation of dislocations and cross slip becomes progressively more difficult. Eventually, when the stacking fault energy is "low" enough, complete dissociation of dislocations is seen to occur as shown in Figs.

Jan 1, 1969

By R. L. Slobod, H. A. Blum

A semiquantitative method for measuring the wettability of reservoir rocks has been developed. These data are needed for reservoir analysis and for interpretation of laboratory displacement studies. The wettability of a core sample is measured by the contact angle for the system oil-water-solid. These contact angles are calculated from the displacement pressure (threshold pressure) obtained by use of the centrifuge, using first oil-water and second air-oil in the same core sample. This method is based on the assumption that the air-oil and oil-water interfaces occupy similar positions in the porous medium when desaturation of the wetting phase is initiated. The assumption is also made that the Contact angle for the air-oil-solid system which is close to zero in value does not change appreciably even when the contact angle for the oil-water-solid system experiences marked changes. "Apparent contact angles'' for five different solids ranging from 31" to 82" have been determined, and changes irr the "apparent contact angle" of a given sample with laboratory use from 33" to 53' {lave been observed. INTRODUCTION Reservoir rocks vary in their wettability, 1,2,3,4 some being preferentially water wet while other are apparently preferentially oil wet. The degree of wettability, in theory, is measured quantitatively by the contact angle for the system solid-oil-water, hut in 1)practice this quantity is extremely difficult to determine." The need for obtaining some measure of this quantity has become obvious in recent years as a result of both laboratory. and field observations. Several reservoir.: such as the Bradford Sand in Pennsylvania and the Wilcox' at Oklahoma City are reported to be oil wet. If these report:: correctly reflect the true nature of the surface of the rock in the ground, then these reservoirs probably will not perform as predicted on the basis of a water wet rock. In the laboratory many core samples have been Observed to be oil wet. These samples, while perhaps not correctly representing the reservoir, have markedly different properties from water wet rock. The location of the phases is different (oil is in contact with rock instead of water), and other quantities such as the connate water, the capillary pressure curve; residual oil. relative permeabilities. and the recovery of oil by water flooding are markedly affected by the value of the contact -4 A further complication observed in the laboratory is the chang-ing of the wettability of a rock specimen with use. such changes mean that repeat runs on the same core are not the duplicate tests desired, but represent new experiments on a more oil wet material. The changes in surface characteristics are sometimes so rapid that by the time an experiment requiring several days is completed, the results may not be representative of the core as originally described, The, rock material itself (Silica. carbonates. etc.), whell Clean and uncontaminated, is water wet. There seems b( : little evidence of the presence of oil wet minerals such as heavy metal sulfides. The oil wetness of reservoir samples, therefore, is believed to be caused by the accumulation of an adsorbed film in which the polar group of a large organic. molecule is adsorbed on the surface leaving the organic or hydrocarbon part of the molecule projecting out from the solid. Such a surface is much more readily wet 17" oil than by water. These considerations indicate the need for a method which will provide some measure of tile wettalbility (Contact(angle if possible) for reservoir rock ..samples) The method should be capable of (1.1 distinguishing between tile wettalility of dif. ferent formation,.. (2) detecting (change. ill wettalbility of a core with use. and (3) measuring the changes in Wettability which may be accomplished with cleaning operations. such as the use of sodium silicate for increasing water wrettalbility." A preliminary report on such a method is preseted below. not with the idea that this procedure alone will Solve the wettabil-ity problem. but rather that it may provide encouragement to

Jan 1, 1952