Search Documents

By Paul Billingsley

Introduction. THE Georgetown mining district is located in Deerlodge county, Mont., about 20 miles west of Anaconda. It lies along the divide between the headwaters of Warm Springs creek, draining eastward, and Flint creek, flowing west and north through the Philipsburg valley. The actual divide is formed by Cable mountain, a narrow ridge running north and south, terminating to the south in low hills overlooking Georgetown lake, and to the north in a high, rugged plateau that falls off to the west to the wide valley of Flint creek. Oil the eastern, or Warm Springs, slope of Cable mountain is the Cable mine, with the Hidden Lake mine a few miles north. On the western slope is the Southern Cross group, with smaller mines, the Twilight, Cincinnati, Red Lion, and Big Bill, at intervals to the northward. The Georgetown mines lie in the hills south of Cable mountain; the Philipsburg mines, of which the Granite Mountain, Bimetallic, Hope, and Trout are the chief, form a separate group to the north, overlooking Flint Creek valley and Philipsburg. (See Fig. 1.1) The region ranges in elevation from 5,000 to 9,000 ft. It is, with the exception of the lower valleys, well timbered with small fir and pine, although Cable mountain and the higher summits to the northward rise slightly above timber line. The main valleys have the smooth contours of glaciation, and their mouths are frequently choked with morainal deposits.

Jan 9, 1913

By O. Hoover, M. Herman, V. V. Damiano

The Jetter and borie' teclznique of determining textures using a spherical specimen has been applied to tlze study of compression-rolled beryllium sheet. Snzall spheres the order of 1 mm in diam cut from the beryllium sheet were autotnatically rotated about tz41o axes using the G.E. single-crystal goniometer. Quantitative pole figures were obtained without tke need to apply absorption corrections. Compression-rolled beryllium exhibited peak intensities ,for (0002) planes of positions tilted 10 deg to the rolling plane and a near random distribution of (1010) planes about the nornal to the rolling plane. TECHNIQUES for determining textures of rolled sheet material are amply described in the literature. The techniques are found to be variations of two basic methods. One due to Decker, Asp, and arker, referred to as the transmission method, utilizes a thin-sheet specimen in which the X-ray beam enters the specimen from one side and the intensity of the beam which emerges from the opposite side is measured. The second method due to chulz,3 referred to as the reflection method, utilizes a thick specimen and the intensity of the beam emerging from the same side is measured. The two rotations of the specimen in the beam are designated a and 8. In order to completely determine the texture of sheet material, it is generally necessary to use a combination of the two methods. The calculations involved in correcting the raw X-ray data for absorption effects and the combining of the data obtained by the two methods are very laborious and time consuming. To avoid the intensity corrections which arise as a result of the changing diffraction volume and path length within the sample other methods have been proposed. The Norton method utilizes a cylindrically shaped specimen cut from the sheet material. Since the rods have rotational symmetry, the absorption correction is constant for rotations about the sheet texture. Jetter and Borie' employed a spherical specimen to analyze the fiber texture of extruded aluminum rods. The spheres were rotated rapidly about the fiber axis to include a large number of grains in the X-ray beam and changes in intensity with respect to tilts of the fiber axis were measured. The absorption correction was constant for all angles and was neglected. The Jetter and Borie' technique finds excellent ap- plication to very fine-grained low-absorbing metals in which the entire sphere volume can contribute to the diffraction volume. In the case of low-absorbing metals, however, serious limitations on specimen thickness occur as demonstrated by Braggs due to de-focussing effects. Peak shifts may occur which negate the assumption that integrated intensities are proportional to peak intensities. These limitations in sphere size to the order of 0.5 to 1 mm for beryllium require that the grain size be sufficiently small to include a large enough statistical sample. The present paper describes the application of spherical specimens less than 1 mm in diam to the quantitative determination of pole figures for compression-rolled beryllium sheet having a grain size the order of 10 p. EXPERIMENTAL 1) Specimen Preparation. Two techniques for spark-machining beryllium spheres were tried. One involved the use of a hollow cylinder as a cutting tool. The tool was fed into the rotating cylindrical specimen as shown in Fig. l(a). The hollow cylinder was carefully aligned such that the axis of the cylinder and the axis of the specimen lay in the same plane and were 90 deg to each other. As the hollow cylinder was fed into the rotating cylindrical specimen, a spherical shape was formed as shown in Fig. 1. Alignment was very critical. Slight misalignment resulted in the formation of a barrel-shaped specimen instead of a sphere. A second technique involved the use of a cutting wheel shaped as shown in Fig. 2 with a groove of the desired radius. A section of the sheet specimen was first turned into a cylinder on the left part of the cutting wheel. It was then shifted to the right and a spherical specimen was turned as shown in Fig. 2. The axis of the cylinder lay in the plane of the sheet. Flats corresponding to the rolling plane of the sheet were used to grip the specimen during the machining operation and these served to identify the rolling plane of the sphere. 2) Rotation of Spec=. The spherical specimen is shown mounted on the G.E. single-crystal goniometer in Fig. 3. The knob A of the goniometer shown in Fig. 3 rotates the specimen about the pedestal axis. These angles have been designated as @ angles. The knob B rotates the specimen about an axis perpendicular to the pedestal axis. These angles have been designated as p angles. A device was made to automatically drive the single-crystal goniometer by means of two flexible shafts connected to the A and B knobs as shown in Fig. 3. The motor system was designed to rotate the knob A, thus rotating the specimen through angles of $I while the B knob remained stationary. After one complete

Jan 1, 1967

By D. C. Reynolds

Recent experiments with II-VI compounds have shown that they hazle considerable potential for laser applications over a broad region of the optical spectrum. It may be possible to cover the spectrum continuously from 3200A (ZnS) to the far infrared (CdHg:Te) since HgTe is a semimetal. At this writing laser action has been observed in ZnS, Zn0, CdS, CdSe, CdS:Se, CdTe, and some of the CdHg:Te alloys. Of particular interest are those lasers operating in the zlisible and near ultraciolet regzons of the spectrum where detectors of high sensitivity are available. The lasing transitions in II-VI compounds are bound exciton transitions some of which have been identified in auxiliary experiments. High efficiencies and low thresholds for lasing hare been achieved almost exc1usively in plutelet-type crystals. The greater crystalline quality exhibited by the phtelet-type material is shown to result from the crystal growth habit. Phonon scattering- of conduction electrons to the ground-state exciton is discussed ill relution to Lou thresholds and high efficiencies for lasing- observed in the CdS:Se solid solutions. The first successful semiconductor laser operation was achieved in the III-V compounds. It is possible to choose a material in this group that will operate between approximately 0.65 and 8.5 . There are at least two reasons why one would like to have a laser operating at shorter wavelengths. First, it would be easier to experiment with a laser operating in the visible region of the spectrum, and also more desirable to have high-in tensity visible light sources. Second, the most sensitive photomul-tiplier detectors are available in the visible and near ultraviolet regions of the spectrum. It is known that II-VI compounds are direct-band-gap semiconductors and as such offer the potential of operating at any specified wavelength between 3200 (ZnS) and 7772A (CdTe). Light emission from II-VI compounds has been the subject of numerous investigations for many years. These investigations were all primarily concerned with noncoherent emission. It has been only recently that coherent emission from these compounds has been observed. To date, laser operation has been demonstrated in CdS, CdSe, and the solid solutions of CdS:Se, ZnS, ZnO, and CdTe. These compounds cover an appreciable portion of the optical spectrum from the ultraviolet to the near infrared. In considering laser applications, the use of lasers in communication's systems offers many desirable features. In any operation of this type one must consider the losses in transmitting the radiation from the source to the detector. Atmospheric absorption in the visible and near ultraviolet is variable and greater than in certain regions of the infrared. It might be concluded that for long-range communication systems an infrared laser operating in a spectral region that is coincident with a transmission window in the atmosphere would be preferable. However, one cannot overlook the possibility of operating a system in the sensitive region of a highly sensitive photomultiplier detector or other light-amplifying system. LASER CONSIDERATIONS To produce a source of coherent radiation it is necessary to achieve a population inversion. In the case of semiconducting materials it is necessary to raise the electrons from one energy state to a higher-energy state relative to it. In semiconductors, this population inversion can be achieved by three different techniques: 1) Current Injection. This technique uses a p-n junction biased in the forward direction. Large numbers of electrons are injected from the n region into the p region, and recombination occurs close to the junction. An inverted population is obtained in this region and the recombination radiation propagates parallel to the junction. This type of pumping has been used in the GaAs junction-type lasers but has not been successfully employed in the II-VI compounds. 2) Optical Pumping. In this case, one uses photons to obtain a population inversion by exciting electrons to higher-energy states. The pump sources are flash lamps or arc lamps and, occasionally, other laser sources when such sources have the appropriate energy for exciting the electrons. The disadvantage of this type of pumping is that flash lamps put out a rather broad spectrum of radiation, whereas the laser material has a rather narrow region of absorption. This results in an inefficient process. Laser sources provide efficient pump sources but the number of usable wavelengths is limited. 3) Electron Beam Pumping. In this technique, the laser sample cavity is bombarded with electrons having energies in the range from approximately 10 to a few hundred kv. The bombarding radiation excites electrons from valence to conduction band states in the semiconductor, giving rise to an inverted population. This type of pumping has been used successfully in several 11-VI compounds.

Jan 1, 1968

By E. F. Koch, J. L. Walter

oriented crystals of iron and iron with 3, 5, and 6.25 pct Si were rolled to reductions of 10 and 70 to 97 pct at room temperature. Similarly oriented crystals were deformed in tension. Dislocation substructures of the deformed crystals were observed by transmission electron microscopy to determine the effect of silicon on the formation of substructures. Pole figures were obtained to relate orientation changes to substructure. When rolled 10 pct, the iron crystals and the 3 pct Si-Fe crystals formed cells, 1 and 0.2 u in diameter, respecliuely. Cells were absent in the higher-silicon crystals. Extended dislocations and possible stacking faults were observed in the 6.25 pct Si-Fe crystal rolled 10 pct and annealed at 650°C. The stacking-fault energy was estimated to be 20 ergs per sq cm. Rolling to 70 pct resulted in the formation of sub-bands (0.9 µ wide) ill the iron crystals and transition bands (containing 0.2-µ-wide subbands) in the 3 pct Si crystals. No subbands formed in the 5 pct Si-Fe crystal until it was ankzealed. SliP occurred on (112) planes ill tension. The slip traces on the 3 pct Si crystal were wary while those on the 5 pct Si crystal wvere straight. The strain-hardening coefficient for the 5 pct Si crystal was nearly zero. Cells did not form, at least at elongations up to 10 pet. The results suggest that cross slip of iron is restricted by additions of silicon beyond about 3 pct possibly by formation of immobile extended dislocations. IN a previous paper' the authors described the substructures developed in (100)[001]-oriented crystals of 3 pct Si-Fe which were rolled to reductions of 10 to 90 pct at room temperature. At low reductions (10 to 20 pct) cells, approximately 0.2 to 0.3 ja in diameter, were formed. The cell walls consisted mainly of edge dislocations. With increasing reduction (up to 50 pct) the cells were seen to elongate in the rolling direction. In certain regions of the crystal there were significant reorientations which were characterized as rotations about an axis normal to the (100) or rolling plane. These regions were called "transition bands". The regions in which there were no reorientations were called ('deformation bands". At reductions of 60 to 70 pct the elongated cells in the transition bands became sub-bands separated by low-angle tilt boundaries with angles of disorientation of about 2 deg. The elongated cell structure in the deformation band was replaced by a general distribution of dislocations. It was noted that the width of the subbands in the transition bands remained 0.2 to 0.3 µ; i .e., the width of the subbands was the same as the initial cell diameter for reductions up to at least 70 pct. From this, and from considerations of the mechanism of formation of the transition bands,' it was concluded that the subbands evolved directly from the initial cells. In order to check this conclusion, it was decided to examine the relationship between initial cell diameter and width of subbands produced by large rolling reductions. Cell size is known to be dependent upon the temperature of deformation.2,3 However, preliminary experiments with 3 pct Si-Fe crystals indicated that the change in cell size with increasing temperature of deform,ation was not sufficient for the present purpose. On the other hand, cell diameters generally reported for iron deformed at room temperature2'3 range from 1 to 2 p, a factor of 3 to 10 larger than the cells in 3 pct Si-Fe rolled to 10 pct reduction,' indicating the possibility of a marked dependence of substructure (at least in terms of cell size) on the amount of silicon in iron. Thus, the investigation was enlarged to include the study of the effects of varying silicon content on substructure in lightly rolled as well as in heavily rolled crystals of iron and iron with 3, 5, and 6.25 pct Si. The crystals used in this study all had the same orientation, (100)[001], with respect to rolling plane and rolling direction. These were rolled to reductions of from 10 to 97 pct and the substructures determined by electron transmission microscopy in both the rolled state and after annealing. In addition, stress-strain curves were obtained from (100)[001]-oriented crystals of iron and 3 and 5 pct Si-Fe to determine the effect of silicon on tensile properties. The dislocation substructure of the tensile specimens was also determined for Samples pulled to 2 and 10 pct elongation at room temperature for comparison with the substructures produced by rolling. 1) EXPERIMENTAL PROCEDURE Crystals with 3, 5, and 6.25 pct Si were prepared by annealing 0.012-in.-thick sheets of high-purity Si-Fe in purified argon at 1200°C to effect growth

Jan 1, 1965

By K. G. Colman

This text is intended to provide the operator and turn-key contractor with the basic data for sizing vibrating screens to be used in ore crushing plants. The basic capacities, modifying factors, etc. used in the area requirement calculations were developed empirically and modified to their present values based upon years of practical applications. It must be pointed out that screening is much more of an art than an exact science, however, the information presented here should provide for reasonably accurate screen sizing when applied to metallic ores .

Jan 1, 1978

By R. O. Leach, O. W. Wagner

Because of unfavorable wetting conditions much residual oil is left when a porous material is Pushed by water. Methods suggested to change reservoir wetting to improve oil displncernrnt efficiency are generally expensitlr. The present 1aborator.y study was undertaken to gain an under.standinx of the factors which determine reservoir wettability, arid to find out if oil displacement efficiency might be improved by a wettahility change accomplished at low cost in on oil reservoir. Contact angle measurements were made on mineral surfaces using sevc.r~zl sets of reservoir oil and water samp1es. Results of the contact angle studies suggest that reservoir wetta-hility may he primarily determined by natural surface-active substances present in the reservoir fluids. The effect of changing sa1inity and pH of the water phase was studied. The re.suits suggest that gross changes in preferential wettability might be acc~o~npli.shed by injection of water containing simple chernicnls to alter pH or salinity in the reservoir. Such treatment could he much less expensive than injection of commercial surface-active agents. Waterflood tests have also been made using synthetic cores and oil and water having wening characteristics similar to those of reservoir fluids. Cores initially oil-wet were flooded in such a way that they were made prefermtial1y water-wct by the advancing flood water. This reversal in preferential wettability achieved greater oil displacement efficiency than when either oil-wet or water-wet conditions were maintained throughout the flood. For the systems studied, the higher the oil viscosity the greater the percentage improvement obtained over conventional waterflood recovery. This suggests that a flooding process making use of wettability-reversal may extend the oil viscosity range over which water flooding is attractive. Because a precise adjustment of reservoir wettability does not seem to be required, and because altering the pH or salinity in some reservoirs may be inexpensive, it appears that a waterflooding process employing wet-[ability-reversal could find .succesful field application. I NTRODUCTION The efficiency with which water will displace oil from a porous material is related to the nature of the capillary forces present. These in turn are controlled by the preferential wetting of the solid by the two fluids. Because of unfavorable wetting conditions, 30 per cent or more of the original oil in place may remain unrecovered in that portion of a reservoir flushed by water. This paper is concerned with the possibility of improving waterflood oil displacement efficiency by alterations in the wettability of the porous material. A laboratory study was made to gain a better understanding of the factors which control reservoir wettability, and to determine if the oil displacement efficiency could be improved by some inexpensive means of manipulating wettability of the porous medium. Contact angle measurements were made with several natural and synthetic oil, water and solid systems (1) to obtain a better understanding of how to duplicate reservoir wettability in the laboratory, and (2) to discover possible means for changing preferential wettability of natural reservoir systems. Flooding tests were also made in synthetic systems to determine if oil displacement efficiency could be improved by those wettability manipulations suggested by the contact angle measurements. Based on these studies a possible method for improving waterflood oil displacement efficiency is presented. This method involves causing an originally oil-wet porous material to become preferentially water-wet during the course of a water flood. The purpose of this paper is to present results of the laboratory studies. THEORY Rock surfaces in some oil reservoirs are believed to be covered with a firmly attached bituminous or other organic coating. Such surfaces would be preferentially oil-wet in the presence of both oil and water, regardless of composition of reservoir fluids. Other reservoirs are believed to contain rock surfaces not permanently coated with such materials, and which would be preferentially wet by water in the presence of water and oil free from surface-active substances. However, when the reservoir fluids do contain certain natural surface-active materials in sufficient quantity, rock surfaces acquire a degree of preferential oil wettability caused by adsorption of these natural surface-active materials on the solid. The equilibrium amount of these materials adsorbed per unit surface area is believed to depend upon their concentration in the bulk liquid phases.

By Frank Ruskey, Richard G. Burdick

Many problems associated with potential hazards in a proposed mining area may not be adequately appraised because of the complexity of trying to evaluate them in terms of production requirements. Frequently, encountered hazards have to be dealt with by day-to-day operational schemes that require the miner to either force a way through them or avoid them by blocking off the area in which the hazards are known to exist. These considerations, after the mine is in full production, can be costly to the mine operator and can increase the danger to the miners. A hazard-evasion computer program for mine planning that will appraise proposed mine layouts on the basis of existing or potential hazards has therefore been developed. The program is intended for use during the planning phase of a mine, where it should assist the mining engineer in making decisions in mine design, With the output from this program, the mining engineer should be able either to corroborate his judgments made on the basis of mining experience or to find unanticipated solutions to design problems. The program tests hundreds of possible solutions to a mining layout, and by sorting out the 10 best (based on a criteria of minimum-abandoned-coal) limits the number of choices that need to be considered and appraised for applicability to a given mine scheme.

Jan 1, 1976

By John E. Sweet

THERE have already been so many subjects of a purely mechanical nature presented to the Institute of Mining Engineers, that it is unnecessary for me to apologize for adding another to the list. When a new invention, or what is supposed to be a new invention, claiming simply an improvement on the well-known devices, is to be described, it is usual to point out the defects of the old and give a history of the object or the art up to date. But, as no doubt a large proportion of the members of this Institute know as much, or more, about the history and use of the steam-engine indicator than I do myself, I will not further preface the subject, than to remind you that what called for the Richards's improvement on the Watt's indicator was high speed ; that the leading improvement was the reduction of momentum in the reciprocating parts; and that this was accomplished by making the parts lighter, and reducing the travel of the heaviest of them, and consequently the speed and momentum. The use of the indicator has been extended, for the speed of steam-engines and other prime movers has been increased, until one engineer at least, John Cooper, of Philadelphia, says, "I want an indicator that will work up to a thousand revolutions." Mr. Thompson, of the Buckeye Steam-Engine Company, of Salem, Ohio, has improved on the Richards's indicator by another reduction in the momentum, which is done by putting the parallel motion nearer the fulcrum of the pencil arm, reducing both weight and travel. The characteristic feature of the indicator I am going to illustrate is a still further reduction in the same direction, which is accomplished by dispensing with the parallel motion altogether. As is often the, case, in putting a simple idea into shape, some difficulties

Jan 1, 1879

By Frank Firmstone

IT is often desirable to obtain one or more accurate horizontal sections of a blast furnace after blowing out. Wishing to do this, last April, in the case of No. 4 furnace at Glendon, which had worn in a very remarkable manner, the method described below was employed, with very good results. A scaffold was fixed in the furnace, and on it was placed a drawing- board, covered with paper, the top of which was made level at exactly the height at which the section was to he taken. (Fig. 8.) The centre of the furnace (which had previously been found, and marked on a plank across the top) was laid off on it by dropping a plumb-bob from above, and a strong needle was driven into the board in the centre. By means of a straight-edge and two plumb- bobs, the line passing through the centres of the front and back arches was also drawn on the board. A pencil was fastened to a light wooden straight-edge at a known

Jan 1, 1875

By Frank Firmstone

It is often desirable to obtain one or more accurate horizontal sections of a blast furnace after blowing out. Wishing to do this, last April, in the case of No. 4 furnace at Glendon, which had worn in a very remarkable manner, the method described below was employed, with very good results. A scaffold was fixed in the furnace, and on it was placed a drawingboard, covered with paper, the top of which was made level at exactly the height at which the section was to he taken. (Fig. 8.) The centre of the furnace (which had previously been found, and marked on a plank across the top) was laid off on it by dropping a plumb-bob from above, and a strong needle was driven into the board in the centre. By means of a straight-edge and two plumbbobs, the line passing through the centres of the front and back arches was also drawn on the board. A pencil was fastened to a light wooden straight-edge at a known

By E. Alan Haley

Accurate and economic control of line and grade on long tunnels, large structures, excavations and waterways has been a problem to surveyors and engineers for decades. The conventional method of surveying, incorporating a level, transit and a number of surveying technicians, has proven to be a very expensive and time-consuming operation. Now, however, engineers have adapted the laser to help ease the problems of surveying, at the same time increasing the efficiency of such operations. The laser, which projects a continuous, narrow red beam of brilliant light, provides a constant alignment reference that does not interfere with personnel or equipment. A complete laser alignment system, specifically designed for and suited to a variety of mining and tunneling operations, has been developed by the Perkin-Elmer Corp. The engineering significance of this development can be fully realized when it is noted that, aside from potentially tremendous economic advantages in terms of labor savings, the laser beam provides a system of alignment that is at least ten times more accurate than presently used optical systems. The new laser system provides accuracies within 10 microinches per foot (1 x 10-5in.) when used with an accessory centering detector. In one of its first field trials, the laser was used for alignment of a two-mile tunnel which showed a total deviation of less than 5/8 in.

Jan 4, 1968

By David H. Browne

One of the most difficult problems in the chemistry of iron-ore, and one, the solution of which, so far as I am aware, has never been attempted, is the distribution, throughout a given vein, of Bessemer ore, and its relation to the formation of the deposit. In those hematite-mines in which both Bessemer and non-Bessemer ore occur, the sorting of the ore as it lies in the deposit becomes a problem of much economic as well as scientific interest. It would seem, from a superficial examination. or, indeed, from any examination not conducted for this especial purpose, as if high- and low-phosphorus ores were mixed in inexplicable confusion ; and a mining-chemist is very apt to fall into a system of adventitious analyses, taking first-class ore wherever he can find it, and overlooking its relation to the formation and position of the vein. I hope that a few notes which I present on this subject may be found worthy of consideration, as throwing a new light upon this obscure topic. During the last three years, while acting as chemist of the Lumberman's Mining Co., I have made some 3000 analyses of iron-ore from the Ludington mine at Iron Mountain, Michigan. These analyses were necessary in order to separate Bessemer and non-Bessemer ore which occurred intermixed in the deposit. During the last year, I attempted in several ways to find some reason or method in the distribution of phosphorus, and have finally become cognizant of the arrangement herein outlined. I have been obliged to confine my attention to our new mine, and, in that, to that portion wherein

Jan 1, 1889

By C. S. Yust, C. S. Morgan

ThIS note reports the observation of masses of dislocation etch pits around the weld necks of small single-crystal particles of calcium fluoride sintered to a cleaved face of a larger CaFz crystal. Crystal particles in the -50 +I00 mesh size range were placed on freshly cleaved CaFz surfaces and heated at 1250°C for 30 min in a tantalum container in an argon atmosphere. The sintered specimens were then etched at room temperature for 40 to 50 min in a 2 pct sulfamic acid solution which is a selective etch for dislocations in caF2.' Figs. 1 through 3 show the masses of dislocation etch pits observed around weld necks after etching. In some cases, particles were gone after removal of the specimens from the furnace although weld necks were readily visible. In other instances, no etch pits formed around a weld neck. A possible cause of concentrations of dislocations on the crystal surface is mechanical deformation of the base crystal when particles are dropped on it. If such a deformation does occur, it would be much smaller than that caused by the light punching of a crystal with a sharp instrument which results in large concentrations of etch pits. However, crystals deformed by punching with the sharp instrument and annealed at the conditions of these experiments (1250°C for 30 min) before etching showed no concentrations of dislocation etch pits. It is obvious that dislocations from the much smaller deformations, possibly created when particles are placed on the surface, would also anneal out. Etching of large crystals which had particles placed on them in the usual manner but which were not heated showed no dislocation concentrations such as shown in Fig. 1. The magnitude of dislocation etch-pit concentrations did not vary with extensive variation of the cooling rate. The appearance of many of the etch-pit clusters is typical of a well-annealed condition, indicating that the dislocation concentrations formed before the specimen temperature was lowered. Therefore, it is evident that thermal stresses in the neck area did not create the deformation indicated by the presence of the dislocations. The possibility exists that the etch-pit concentrations at places where particles had been removed may be the result of deformation accompanying the fracture of the sintered bond. That this is not so was demonstrated by breaking off particles around which no etch pits occurred. Re-etching never resulted in the large concentrations observed at sintering sites. The stress available to effect material movement during sintering of two particles will depend on the geometry at the contact point but can easily exceed the macroscopic yield stress in CaFz systems. It appears that the plastic deformation observed results from sintering or simply from the weight of the small particles. It has been previously argued that plastic flow makes an important contribution to the initial densification of oxides having the fluorite crystal structure.2p3 If plastic deformation occurs, it would begin as soon as the temperature is sufficiently high

Jan 1, 1967

By Charles Barron McIntosh

BECAUSE of the well known relationship between a low atmospheric pressure and increased amounts of methane in coal mines, attempts have been made to find associations between low pressures and coal mine explosions. An early study by F. Able disclaimed this relationship. He found that half the explosions took place during a rising barometer when methane content in a ventilated mine would be decreasing. A more recent study by C. L. Hosler revealed a close relationship between anthracite mine explosions and low atmospheric pressure. Bituminous coal mine explosions, where coal dust as well as methane can be exploded, were found to be more closely associated with a rising pressure following a low barometer than with the falling or low pressure period. Emphasis on rising pressure periods led the present writer to investigate the effect of the post-frontal or post-cyclonic weather on coal dust. Dust samples of uniform mesh were exposed in an Illinois mine. Analyses of the dust taken before and after the passage of cold fronts and their accompanying low pressure troughs indicated an increase in coal dust moisture prior to a frontal passage and loss of moisture from coal dust following the time of lowest pressure. Thus the warm, moist air (Tropical Maritime)found over the mine during the falling pressure period was cooled in the mine and moisture added to the dust. Cold, dry air (Polar Continental) accompanies' the rising barometer following a frontal passage and the air, being heated in the mine, subtracted moisture from the coal dust. A similar but seasonal phenomenon occurs from summer to winter, the dry dust period in winter being recognized as the more dangerous period. The question arose as to how the short period or daily changes in moisture content of coal dust compared with the seasonal changes. Temperature and humidity statistics were obtained from the surface and mine entry for the months of July andJanuary. The gain and Ioss of mdisture. to the hine were calculated for these two morths as were the gain and loss associated with mT (Tropical Maritime) and cP (Polar Continental),air masses as observed in the investigatiynsl. Temperature and humidity statistics tigatiynsl.taken from [the two air masses represent atimp span of only 34 hr. The redultant changes as presented in the accompanying table verify the supposition that short period changes in coal mine moisture may attain the magnitude of recognized dangerous seasonal changes. Statistics for the mT air and the July air have been placed next each other and those for cP and January air together for easier comparison of the two warm and two cold air units. The last column readily reveals that there is little difference in the amount of moisture being deposited in the mine from the mT air and the July average air. A similar conclusion is reached regarding the loss of moisture from the mine when it is affected by the cP air mass or the average January air. This comparison would be particularly true from late fall through early spring when strongly contrasting air mass changes are a common occurrence. The invasion of cold, dry air following a cold front thus produces a drying period that could well receive more attention as a danger period for coal dust explosions. This drying period would compare with Able's explosion period during a rising barometer. The drying period is also perltinent in Hosler's findings, where it was noted that the average explosion day (for bituminous coal mines) followed the day of lowest atmospheric pressure. Moreover, the author's investigation of some 365 coal mine explosions also indicates that this post-frontal period should receive special attention in connection with mine safety measures. Two comparatively recent major explosions in Illinois (Centralia and West Frapkfort) occurred after the mines had been under the influence of cold-dry air for 25 to 30 hr-following a deep low pressure passage. Dust was the important explosive element in both these explosions.

Jan 1, 1958

By William H. Spice

The fault zone of south central Texas showed renewed activity during I940 along a trend roughly paralleling the old established Balcones fault-line group of producing fields. This was a result of the new discoveries in the Wilcox (Eocene) formation in southeastern Texas and Louisiana. As of the end of the year, one new field producing from the Wilcox formation had been discovered on the Washburn ranch in La Salle County, along the southwestern limits of the district, and several projected tests into that formation were under way. In the western part of the district, par-titularly in the part of the Rio Grande embayment that is in Dimmit, Webb and Zavala Counties, there has been renewed leasing activity with the shallower sands in the Navarro-Taylor formations (Upper Cretaceous) as the objective in several projected tests for the early part of 1941. Three new fields have been discovered along the old fault-line trend, but these have been comparatively small, producing either from Dale lime, Austin chalk or Buda lime. No new fields were discovered during the Year in the Edwards (Lower Cretaceous) lime horizon. Approximately 260 wells were drilled in the district during 1940, which resulted in four new oil fields. Twenty-seven new wells were completed in the Proven Edwards lime fields of Darst Creek, Luling and Salt Flat and seven were added to production in the Pearsall field. Approximately 160 wells in 18 counties were completed as failures during the year. The district produced 7,659,634 bbl. during 1940, which was a 9 per cent decrease under production for 1939. In all, 3559 wells were producing at the end of I940, compared with 3562 wells producing at the end of the previous year; 104 new producing wells were completed and 163 wells were abandoned in the producing fields of the district. During 1940 considerable exploratory work was carried on along the Wilcox trend within the district, particularly by major companies employing various types of geophysical methods, and leasing activity increased considerably. At the end of the year, the total number of acres of nonproducing leases held by major companies in the district increased about 10 per cent. It is anticipated that this activity will continue into the first part of 1941 and will be supplemented by several exploratory test wells. New Fields B,, Creek, Caldwett County.— . R. Ogden NO. 2 Talley, discovery well of the Bee Creek field, in the northeastern part of Caldwell County, was completed on March 16, I940, in Dale lime from 2091 to 2238 ft., pumping 85 bbl. per day, 39° A.P.1. gravity. The discovery of this field can be credited to a combination of subsurface geology and magnetometer work, which indicated the presence of a serpentine intrusion. At the end of the year, ,3 producing oil wells had been completed and the field has produced a total of 47,050 barrels.

Jan 1, 1941

By William H. Spice

The fault zone of south central Texas showed renewed activity during I940 along a trend roughly paralleling the old established Balcones fault-line group of producing fields. This was a result of the new discoveries in the Wilcox (Eocene) formation in southeastern Texas and Louisiana. As of the end of the year, one new field producing from the Wilcox formation had been discovered on the Washburn ranch in La Salle County, along the southwestern limits of the district, and several projected tests into that formation were under way. In the western part of the district, par-titularly in the part of the Rio Grande embayment that is in Dimmit, Webb and Zavala Counties, there has been renewed leasing activity with the shallower sands in the Navarro-Taylor formations (Upper Cretaceous) as the objective in several projected tests for the early part of 1941. Three new fields have been discovered along the old fault-line trend, but these have been comparatively small, producing either from Dale lime, Austin chalk or Buda lime. No new fields were discovered during the Year in the Edwards (Lower Cretaceous) lime horizon. Approximately 260 wells were drilled in the district during 1940, which resulted in four new oil fields. Twenty-seven new wells were completed in the Proven Edwards lime fields of Darst Creek, Luling and Salt Flat and seven were added to production in the Pearsall field. Approximately 160 wells in 18 counties were completed as failures during the year. The district produced 7,659,634 bbl. during 1940, which was a 9 per cent decrease under production for 1939. In all, 3559 wells were producing at the end of I940, compared with 3562 wells producing at the end of the previous year; 104 new producing wells were completed and 163 wells were abandoned in the producing fields of the district. During 1940 considerable exploratory work was carried on along the Wilcox trend within the district, particularly by major companies employing various types of geophysical methods, and leasing activity increased considerably. At the end of the year, the total number of acres of nonproducing leases held by major companies in the district increased about 10 per cent. It is anticipated that this activity will continue into the first part of 1941 and will be supplemented by several exploratory test wells. New Fields B,, Creek, Caldwett County.— . R. Ogden NO. 2 Talley, discovery well of the Bee Creek field, in the northeastern part of Caldwell County, was completed on March 16, I940, in Dale lime from 2091 to 2238 ft., pumping 85 bbl. per day, 39° A.P.1. gravity. The discovery of this field can be credited to a combination of subsurface geology and magnetometer work, which indicated the presence of a serpentine intrusion. At the end of the year, ,3 producing oil wells had been completed and the field has produced a total of 47,050 barrels.

Jan 1, 1941

By Frederick T. Fischer

The New Jersey Zinc Company began a program of exploration in Middle Tennessee in 1964. The target horizon of the exploration project has been the Knox Dolomite which is a low-yield aquifer over nearly the entire Central Basin of Tennessee (1). With the exception of a few hundred acres in the Wells Creek and Flynn Creek disturbances (astroblemes?), the Knox Dolomite in Middle Tennessee is known only in subsurface. In January of 1969, New Jersey Zinc announced the discovery of a major zinc deposit near Elmwood, southeast of Carthage. This is on the northeastern flank of the Nashville Dome where the nearly flat-lying beds have an average eastward slope of about 50 feet per mile. The anticipated development of a mining situation has emphasized the significance of hydrologic relationships in the region as a whole and especially in the Elmwood area. These relationships affect several areas of concern which ma be generally grouped into two broad classes; i. e. , (1) Problems of a Public Nature - involving the prevention of the contamination of potable aquifers, the prevention of the contamination of surface waters, the prevention of the capture of presently utilized water, etc.; and (2) Problems of Mining Economics - involving pumping capacity and costs, the possible need for equipment of special composition, underground environmental conditions, etc. Exploration drilling in Middle Tennessee has contributed additional information about the Knox aquifer and

Jan 1, 1970

By G. J. Saulnier, K. E. Goddard

The US Geological Survey has developed mathematical modeling techniques to assess potential impacts on the hydrologic system resulting from mining of coal and oil shale in northwestern Colorado. Potential impacts of oil shale mining on groundwater hydrology have been simulated using a quasi-three-dimensional, finite-difference model. The model has been used to simulate hypothetical mine dewatering operations at two proposed oil shale mines. Dissolved-solids distribution and solute transport were simulated with a three-dimensional, finite-difference model that was used to evaluate the effects of flooding in hypothetical abandoned mines. The potential impacts of coal and oil shale mining on water-sheds were investigated using a digital watershed model. This deterministic physical-process model predicts responses of the hydrologic system to modifications resulting from mining in basins having snow as the major source of runoff and recharge. Potential impacts of coal development on surface water quality were investigated using a river quality assessment model. The models developed by the US Geological Survey have been useful in defining the potential effects of mining in northwestern Colorado. They are an important first step in analyzing the existing data base and in predicting impacts and new data needs. The models may not be totally applicable on the local scale but are very meaningful on the regional level.

Jan 1, 1983

By R. W. Raymond

That the death of Martin Coryell, which occurred at Lambertville, New Jersey, on Monday morning, November 29th, touched the sympathies of a wide circle of professional associates and personal friends, was amply testified by the gathering at the funeral services on Friday. Like his distinguished friend and neighbor, the late Ashbel Welch, Mr. Coryell was one of those pioneers in American engineering to whom we owe the great railway and canal systems which lie at the base of our national prosperity, and who have consequently enjoyed the respect and esteem of their successors of the present generation. Martin Coryell was born July 20th, 1815, at New ope, Rucks County, Pa., and was educated principally in the schools of his native town arid of Lambertville, New Jersey, to which place he returned for permanent residence fifty years later. With the exception of a brief period in youth, during which, to restore his failing health, he learned and practiced for a few months the carpenter's trade, and another brief period, later in life, when he read law for a time in the office of B. H. Brewster, of Philadelphia, afterwards Attorney-General of the United States, Mr. Coryell may be said to have spent his life as an active civil and mining engineer. Even these two episodes can scarcely be said to have been deviations from that profession, since they served to give him more thorough preparation for constructive and administrative work. The Delaware Division Canal, the Raritan Canal, and the Brunswick Canal, are among those upon which Mr. Coryell was employed. For the Raritan Canal Company, under the superintendence of Ashbel Welch, he located the greater part of the Belvidere Railroad (now the Belvidere division of the Pennsylvania Railroad), and directed its construction from Trenton to Lambertville. He was also active as a mining engineer, being one of the early pioneers of mining in the Lake Superior copper region, and had much to do with the development of the Hazleton coalfield and the railroad which has since expanded into the Lehigh Valley system. In 1862, he removed to Wilkes-Barre, where, in 1864, he became manager of the Warrior Run Mining Company. One of the editors

Jan 1, 1887

By D. T. Jones

In view of the importance of the application of scientific principles to the production of oil from the reservoir, the Production Staff of the Anglo-Iranian Oil Co. (late Anglo-Persian Oil Co.) has been engaged for some years on an intensive program of research on the physical properties of crude oil. Problems involving the retention of crude oil in capillaries and fine fissures demanded for their solution a knowledge of the surface tension and specific gravity of the crude under reservoir conditions, and it is the purpose of this paper to describe briefly the methods adopted for the determination of these properties, and to present the more important results. A detailed article was published in volume 1 of the World Congress Proceedings (1933). Surface-tension observations on crude oil regassed at high pressures with natural gases have been made in the past by Beecher and Park-hurstl and Swartz2, but up to the time of the investigations in Iran no one seems to have carried out experiments with gas-saturated crude direct from the reservoir and kept at its original pressure. Results obtained in this manner are obviously of greater practical value for solving problems connected with the reservoir. Method of Measurement No apparatus for the measurements, under the pressure conditions involved, was available, and a suitable instrument had to be designed and constructed in the Fields workshops. Careful consideration of the matter led to the adoption of a method for measuring the surface tension which did not involve a knowledge of the specific gravity of the oils under the working conditions: the main reason for this being that up to that time no accurate determination of the specific gravity had been made under these conditions. The method adopted involves the measurement of the actual tension in an oil film, and is effected by means of

Jan 1, 1936