Search Documents

By B. L. Landrum, P. B. Crawford

Theoretical and potentiometric model studies have been made of the effect of non-uniform lateral permeabilities on pattern sweep efficiency and production capacity in waterflood and gas-cycling programs. It is shown that a diflerence in directional permeability by a factor of three may result in a sweep efficiency of only 43 per cent for a five-spot pattern or a sweep of either 79 or 38 per cent for a direct line-drive square pattern, depending on the direction of the line-drive flood. Changes in the pattern conductivity varied from about 0.8 to 1.34 over this same permeability variation, depending on the pattern used. It is suggested that measurements be made to determine the possible magnitude and extent of the directional permeability phenomenon early in the field developinent and certainly prior to the initiation of any fluid-injection progmm. INTRODUCTION Irregularities in reservoir sand properties long have been a major difficulty to anyone attempting to explicitly describe the field characteristics of oil production. In particular, it is well known that vertical and lateral permeabilities often differ appreciably; however, the existence of large regions with lateral permeabflity variation is not widely recognized. A number of years ago, extensive studies were conducted by the Secondary Recovery Research Labcratory of the Pennsylvania Grade Crude Oil Association, primarily on the Bradford field. Johnson and Hughes' reported a permeability trend in the northeast-southwest direction. They indicated that flow in the preferred direction may be 25 to 30 per cent greater in that direction than in the northwest-southeast direction. They also reported that similar effects may be found in other nearby fields. The origin of the permeability variation has been discussed by Griffith Hutchinson' described the results of labora- tory tests on limestone cores, pointing out that per-ferential directional permeabilities were significant in one-half of 10 formations studied and that the average permeability ratio was 16:1. Barfield, Jordan and Moore analyzed the fluid-injection displacement performance in the Spraberry and reported that the effective ratio of permeability parallel to the major axis to the permeability perpendicular to this axis was 144:l and that it inclined along an angle of about 30". To prevent the reduction of sweep efficiency which would normally result from flooding or cycling in such reservoirs, well spacing could be varied from the customary square to a diamond-shaped pattern. Johnson and Hughes' presented a method for determining the desired shape. Another method will be discussed in detail in the next section. It is the purpose of this paper to investigate quantitatively the effect of directional permeability upon the sweep efficiency and production capacity of the five-spot and line-drive well patterns. Information currently in the literature will be applied to this particular problem and augmented by a potentiometric model study. It is stressed that the effects herein discussed may or may not be of great importance because field data on this phenomenon are far too scant to form such an opinion. It is suggested that, if conditions similar to those found by Johnson and Hughes frequently exist (as may well be the case), more consideration cdrtainly should be given to this problem.

By R. V. Norris

IRving Ariel Stearns died at his home, 60 South River St., Wilkes-Barre, Pa., on Tuesday morning, Oct. 5, 1920, of pneumonia, after an illness of about a month. In his death, the Wyoming Valley loses one oflits most eminent and best loved citizens, and the loss of so strong a participant in the activities of the Valley will leave a gap most difficult to fill. Despite his more than three score and fifteen years, Mr. Stearns, at the time of his death, was president of the Wilkes-Barre City Hospital, Wyoming National Bank, and the Wyoming Historical and Geological Society, chairman of the Board of the Vulcan Iron Works, and a director of the Spring Brook Water Supply Co., and of the Wilkes-Barre Lace Manufacturing Co. Mr. Stearns came of New England stock, a descendant in the eighth generation of Charles Stearns who was admitted freeman in Watertown in 1646. Irving Ariel Stearns was born Sept. 12, 1845, in Rushville, N. Y., a son of George W. and Miranda (Tufts) Stearns. He was graduated from the Rensselaer Polytechnic Institute of Troy, N. Y., in the celebrated Class of 1868. After graduation, he was assistant professor of chemistry in charge of the analytical laboratory for a year, then went to Wilkes-Barre in 1869, as engineer in the office of R. P. Rothwell, at that time the leading mining engineer of the region. From 1871 to 1872, he was superintendent of the McNeal Coal & Iron Co. of Schuylkill County, Pa. and in 1872 succeeded to Mr. Rothwell's business when the latter became editor of the Engineering & Mining Journal of New York. From 1872 to 1885, Mr. stearns was in private practice as a mining engineer, handling a great amount of business in the anthracite region, including the building of the bridges at Shickshinny and Pittston, and the surveying and mapping of many of the individually operated mines. His practice extended throughout the country, with numerous examinations and reports upon mining properties in Pennsylvania, Virginia, West Virginia, Arkansas, Colorado, California, Wyoming, Idaho and Utah; he was responsible for the design and execution of the Lehigh Valley Railroad Co.'s great Tifft Farm improvements at Buffalo, N. Y. including canals, docks, coal stocking plant, etc. He was commissioned Quartermaster of the Ninth Regiment, N. G. P., March 29, 1880, was promoted to Major on May 15, 1884, and resigned Apr. 1, 1885. He always retained his interest in the National Guard and was trustee and president of the Ninth Regiment Armory Association.

Jan 1, 1922

By R. V. Norris

IRving Ariel Stearns died at his home, 60 South River St., Wilkes-Barre, Pa., on Tuesday morning, Oct. 5, 1920, of pneumonia, after an illness of about a month. In his death, the Wyoming Valley loses one oflits most eminent and best loved citizens, and the loss of so strong a participant in the activities of the Valley will leave a gap most difficult to fill. Despite his more than three score and fifteen years, Mr. Stearns, at the time of his death, was president of the Wilkes-Barre City Hospital, Wyoming National Bank, and the Wyoming Historical and Geological Society, chairman of the Board of the Vulcan Iron Works, and a director of the Spring Brook Water Supply Co., and of the Wilkes-Barre Lace Manufacturing Co. Mr. Stearns came of New England stock, a descendant in the eighth generation of Charles Stearns who was admitted freeman in Watertown in 1646. Irving Ariel Stearns was born Sept. 12, 1845, in Rushville, N. Y., a son of George W. and Miranda (Tufts) Stearns. He was graduated from the Rensselaer Polytechnic Institute of Troy, N. Y., in the celebrated Class of 1868. After graduation, he was assistant professor of chemistry in charge of the analytical laboratory for a year, then went to Wilkes-Barre in 1869, as engineer in the office of R. P. Rothwell, at that time the leading mining engineer of the region. From 1871 to 1872, he was superintendent of the McNeal Coal & Iron Co. of Schuylkill County, Pa. and in 1872 succeeded to Mr. Rothwell's business when the latter became editor of the Engineering & Mining Journal of New York. From 1872 to 1885, Mr. stearns was in private practice as a mining engineer, handling a great amount of business in the anthracite region, including the building of the bridges at Shickshinny and Pittston, and the surveying and mapping of many of the individually operated mines. His practice extended throughout the country, with numerous examinations and reports upon mining properties in Pennsylvania, Virginia, West Virginia, Arkansas, Colorado, California, Wyoming, Idaho and Utah; he was responsible for the design and execution of the Lehigh Valley Railroad Co.'s great Tifft Farm improvements at Buffalo, N. Y. including canals, docks, coal stocking plant, etc. He was commissioned Quartermaster of the Ninth Regiment, N. G. P., March 29, 1880, was promoted to Major on May 15, 1884, and resigned Apr. 1, 1885. He always retained his interest in the National Guard and was trustee and president of the Ninth Regiment Armory Association.

Jan 1, 1922

By H. G. Doll

A new electrical logging method is described which measures the resistivity of small volumes of material near and behind the wall of the bore holes. The very small electrode systems used are supported in the face of the flexible insulator pad of appropriate dimension maintained in contact with the wall. The measurements are recorded simultaneously with two different electrode spacings. This method provides a very detailed record of the formations and particularly of the permeable beds traversed by the bore holes. The application of MicroLog to the location of permeable zones within compact formaltions, such as limestone, and to the determination of the amount of sand existing in sequences of thin shale and sand streaks is discussed. The possibility of quantitative determination, providing a step toward the evaluation of formation porosity and mud cake thickness, is also examined. Field examples illustrate the essential features of the method. INTRODUCTION In conventional electrical logging, the spontaneous potential (SP) log is used to delineate the permeable beds, and the resistivity logs are used primarily to provide indications concerning the fluid content of the beds. When the formations are much more resistive than the mud, as happens, for example, in limestone fields, the SP currents are short-circuited by the more conductive mud column, with the result that the SP log is quite rounded. In that case, the SP log generally gives the approximate location of the permeable formations but it cannot be used for an accurate determination of the boundaries of each permeable bed.' Solutions for the problem of obtaining a better determination of the permeable beds in limestone fields were developed from two angles. One approach consisted in improvements to the logging of the SP, as given by Selective SP logging and Static SP logging. These new methods, which have been described in an earlier paper,' give good results when the mud is not too salty, but they are still in a somewhat experimental stage, mostly because the development efforts have lately been concentrated on another approach to the problem, i.e., the MicroLog.

Jan 1, 1950

By E. D. Gardner

The tide of increasing demand for metals turned during early 1949, with resultant lower prices. The production of the principal metals was less than in 1948. The problem of high unit costs, however, was held over from 1948. With the lower prices for metals, greater efforts are being made to reduce operating costs. The labor supply was adequate during the latter half of the year in most districts. The force has been reduced at most mines; some mines were idle during part of the year because of strikes, and others ceased operations on their own account. In the main, labor efficiency increased during the year in underground metal mines. Efforts are being made generally to improve labor relations. Green men hired in the time of the scarcity of skilled miners are becoming better trained. The supervisory personnel of most mines is cost conscious, and the planning of operations has been improved. Overhead costs are being scrutinized. The trend toward mechanization underground continued strong. Mining technology rapidly is becoming a problem of handling materials. Surface miners, underground miners and miners of metals, nonmetallics, and coal can learn much Gardner from each other. A mine, however, may become overmechanized. The capital charges against new equipment may exceed the saving in labor costs where sufficient daily tonnage is not handled.

Jan 1, 1950

By L. D. Jaffe

THE data recently published1-" on heat treatment of titanium alloys have not been readily systematized into an overall picture. When the ß titanium phase transforms isothermally at low temperatures, the hardness follows a typical age-hardening pattern, going through a peak as schematized by the "hardness" vs "time of isothermal transformation" coordinates of Fig. 1. As the temperature is raised, the peak will decrease in height and occur at shorter times; slowing must however take place as the /3 transus is approached. The brittle microconstituent in the region of peak hardness has been termed /3'. Its structure is still undetermined but it is clearly a transition stage from soft /3 to the £ + a that is found at the right of the peak. On continuous cooling, high cooling rates correspond to short times on Fig. 1; abscissa labeling has been added accordingly. Extremely rapid cooling will retain soft /3; very slow cooling will precipitate soft a; intermediate rates give hard 8'. Increasing distance from the water-quenched end of a Jominy hardenability bar corresponds to slower cooling (right on Fig. I), but the range of cooling rates covered by a Jominy bar is only a small portion of that shown in the figure. The p-stabilizing alloying elements retard the transformation process, moving the material to the left on Fig. 1. A lean alloy is harder water-quenched (P') than air-cooled (/3 +a); a rich alloy is harder air-cooled (/3') than water-quenched (/3). Examples of the position of various compositions with respect to the curve, based on limited data in the literature, are given at the top of the figure. Oxygen and carbon accelerate the transformation process, moving the material to the right on Fig. 1. If an alloy quenched quickly enough to retain soft /3 is reheated below the £ transus (tempered), it ages, going through a hardness maximum as time increases (moving right on Fig. 1). Material which after cooling from the /3 range lies on or right of the hardness peak, will move still further right on tempering, and so soften. Since the rate of the tempering (aging) reaction increases with temperature, the figure also may be used to represent the variation in properties with tempering temperature, at short tempering times. The simple picture given here neglects martensite transformation, as well as differences between decomposition products of /3 formed by direct isothermal transformation and those formed by quenching and tempering. It may nevertheless be of use as a guide for practical heat treatment and for further research.

Jan 1, 1955

By W. C. Krumbein

GEOLOGICAL problems are approached from a geometrical (space relations) viewpoint, a kinematical (time sequence) viewpoint, or a dynamical viewpoint. The first two require sound training in conventional geology and in field methods. The third approach requires a solid foundation of chemistry, physics, and mathematics. Modern training for geologists should include close integration of basic sciences with geological principles. INTRODUCTION Our knowledge of the earth has increased tremendously during the last half century. We know more about its surface configuration, the distribution of its natural resources, the procession of living forms that inhabited it in the past, the chemical composition of its oceans, the areal distribution of its surface rocks, the movements of its atmosphere, and so on. Not only do we know more facts about the earth, but we have a better understanding of the processes that take place on and within it, such as the nature of earthquakes, the thermodynamics of the atmosphere, the chemical equilibria involved in the formation of igneous rocks, the mechanics of stream flow, the dynamics of the earth's origin, and so on. Many sciences contributed to the sum total of this knowledge, including such established disciplines as geology, geography, physics, chemistry, astronomy, biology. Out of this accumulation of new knowledge grew also a group of new sciences, such as seismology, oceanography, meteorology, volcanology, hydrology. Collectively these latter are known as the geophysical and geochemical sciences, and to a large extent they began as branches of geology. Until the turn of the century, for example, the study of earthquakes (seismology) was a part of geology, although as early as 1846 Mallet, a physicist, had suggested that the subject could be investigated by elastic-wave theory. Comparatively little progress was made along these lines until the seismograph was developed near the turn of the century; since then, additional earthquake data have accumulated rapidly, but more important, the interpretation of these data essentially has kept pace with their accumulation. In similar fashion, meteorology was generally considered a branch of geology as recently as one or two decades ago. Considerable progress had been made in such aspects as weather forecasting, but the science dates its recent rapid rise from the year 1911, when Bjerknes first applied the principles of dynamics to the analysis of air masses. The rapid development of such disciplines as oceanography, volcanology and hydrology was due in part to the application of principles of chemical equilibrium, of dynamics, and of thermodynamics to earth problems, by men who were essentially physicists or chemists by training. The last half century, therefore, and particularly the last two decades, saw the influx of numerous chemists and physicists into the realm of the earth sciences. In the meantime the main body of geology itself showed a marked growth, and

Jan 1, 1941

C. W. GENNET, JR.,* Chicago, 111. (written discussion?).-Since the Lehigh Valley accident, transverse fissures have become a source of constant anxiety to railroad officials, because such defects, only infrequently detected by the trackmen, may appear under a moving train entirely without warning. The number of actual accidents resulting from rails containing fissures is no doubt a small proportion of the total, but the serious losses that have been directly attributable to fissures, coupled with the continual possibility of repetition, creates an alarming situation which demands a full investigation of the cause of fissures; apart from other types of rail failures. Mr. Howard's position gives him a field for action and an opportunity for laboratory examination and research that are unsurpassed, and the results. of his investigations must be received with the utmost attention and respect. His admirable paper, summarizing his previously published studies and analyses of the transverse fissure problem, constitutes a convincing treatment of the subject chiefly from the standpoint of stress and strain to which rails are subjected. The intricacies of the problem are so great that seemingly any theory advanced for the cause of fissures may be attacked from some angle; and although Mr. Howard's deductions are logical in the direction followed, it is apparently necessary for considerable work to be done along other lines before his theories can be fully accepted. It is generally conceded that fissures, whether fundamentally clue to fatigue or something else, are of a progressive character, their ultimate size' being the result of growth from an originating nucleus or point of rupture. Abundant proof of this lies in the variable sizes of the fissures found, and there can be no doubt that their development or growth is the result of the strains to which rails are subjected in the track. Obviously, therefore, the most important factor in investigating the cause for fissures lies in determining the conditions that exist at the point or

Jan 4, 1918

(Members are urged to send in for this column any notes of interest concerning themselves or their fellow-members.) Members and guests who called at Institute headquarters during the period August 1, 1916 to September 10, 1916: C. L. Cantley, New Glasgow, N. S. H. M. La Follette, La Follette, Tenn. D. A. Cowell, Columbus, Ohio. Montrose L. Lee, Montevideo, Uruguay. Alexander Deussen, Houston, Texas. V. H. McNutt, Billings, Mont. Chas. E. Dutton, Goldfield, Nev. J. W. Maller, New York, N. Y. H. S. Emlaw, Grand Haven, Mich. Edwin W. Mills, Tul. Mi Chung, Chosen, J. M. Gillette, Swatsburg, N. Y. Korea. E. Gorilla, San Antonio, Texas. Francis R. Pine, Elizabeth N. J. Bertram Grant, Kingman, Arizona. Frank A. Ray, Columbus, Ohio. Ruger W. Hay, Bisbee, Arizona. John A. Rice, El Paso, Texas. C. F. Hendricks, Cobalt, Ontario. W. E. Rice, Ringwood Manor, N. J. Stanley C. Herold, San Jose, Cal. W. H. Staver, Lynchburg, Va. Lloyd Hoffman, Pottersville, N. J. Ralph H. Sweetser, Easton, Pa. Charles Hunter, London, England. Kirby Thomas, New York, N. Y. G. Jansen, Benkoelen, Sumatra. Henry Traphagen, Union Hill. T. H. Jenks, Oatman, Arizona. M. M. Valerius, Tulsa, Okla. Warren jenny, Chanaral, Chile. Wilfrid B. Wainewright, London, Eng. Walter A. Barrows, Jr., of Brainerd, Minn., has been elected president and general manager of the Thomas Iron Co., Easton, Pa., to succeed Ralph H. Sweetser, whose resignation of several months ago becomes

Jan 10, 1916

By Helmut Thielsch

METALLOGRAPHIC specimens whose surfaces are to be investigated are too thick to allow either light or electrons to pass through them for microexamination by transmission. This difficulty is overcome with optical microscopes by illuminating the surface through the objective lens. For electron microscopes best results are obtained by preparing thin replicas of the surface of the specimen, placing them in the microscope and passing the electron beam through them. Since electron microscopes represent a rather recent invention, they have found little application as compared with optical microscopes. This is true because, aside from the cost of new equipment and development of new techniques, some of the older replica methods necessitated the destruction of the surface from which a thin transparent replica was obtained. In other processes in which the surface is preserved, either too tedious a procedure is required, unsuited to "mass-production " requirements of industrial laboratories, or replicas of insufficient contrast and sharpness are produced. In general, investigations with the electron microscope involve five steps: (I) polishing the surface of the metal specimen, (2) proper etching of the surface, (3) preparing the suitable replica from the surface, (4) examination and photography in electron microscope and (5) interpretation. PREPARATION OF METAL SURFACES Usual metallographic polishing is generally satisfactory. It is important though that the final polish be applied very care- fully, since otherwise evidence of a small amount of deformation might show up even on relatively deeply etched surfaces. A high-power microscope should be used to determine the suitability of the polish and etch. This, of course, is not different from optical examinations, but in these, if a deep etch is used, the problem is less serious. It is frequently difficult to detect with optical microscopes poor polishing aside from superficial scratches before etching. Figs. I and 2 show micrographs of "well" and "poorly" polished nickel etched by immersing the same for 20 min. in a solution containing 8 grams cupricsulphate in 40 C.C. of concentrated HCl and 40 C.C. of H20 (Marble's reagent). The sample shown in Fig. I was polished in its final stages for 5 min. on a carborundum wheel followed by 10 min. on a rouge wheel, whereas the sample shown in Fig. 2 was polished only I min. on the rouge wheel. Generally, this procedure does not guarantee that the surface of the specimen will be either undistorted or deformed. It was applied here merely to show the effects of good and poor polishing. To the experienced investigator, plastic deformation is

Jan 1, 1946

RECORDING that the latest annual meeting was the largest and most successful ever held has be-come almost a habit, but when, as this year, the registration on the first day exceeded any other first day by two hundred, the annual dinner attracted nearly 1200, as compared with 750 at the previous largest one, and the number of technical sessions was larger than ever before, there seems no escape from so regarding it. In spite of the third day being a legal holiday (Washington's Birthday) no slackening, in attendance and interest was noted, and throughout the four days the greatest problem was to find enough meeting rooms and chairs to provide for the sessions, of which as many as twelve were in progress at one time. Solution of the problem would not have been possible (since the Engi-neering Societies building, was designed to provide only three general meeting rooms) except that a part of the eighth floor happened to be temporarily vacant. As these extra rooms will not be available next year, it may become necessary to adopt measures to keep the annual meeting down to the limit of facilities for handling it. The meeting opened on Monday with simultaneous sessions on iron and steel, geophysical prospecting, mine ventilation, non-metallic minerals, and milling, methods. The first four, which were continued after the usual recess for lunch, are reported in more detail elsewhere.

Jan 3, 1928

By Jr. W. L . Phillips

The deformation and fracture characteristics of lithium-fluoride single crystals stressed in compression at room temperature have been studied. In as-cleaved specimens the stress-strain curves were variable; two types of {110} fractures were observed in the vicinity of kink bands. The stress-strain curves of annealed crystals were reproducible; {100} cracks formed which propagated along the (100) and (110) planes. The deformation and fracture characteristics were affected by quenching and X-ray irradiation. STUDY of the mechanical behavior of nonmetallic materials has received considerable impetus in recent years because of the need to overcome the problem of brittleness before the refractory properties of nonmetallics can be fully exploited. Ionic crystals provide a convenient and simplified starting point from which to study the deformation and fracture processes in nonmetallic materials. Early investigations of the mechanical behavior of non-metals were restricted largely to determinations of the crystallographic indices of the cleavage and fracture planes and the glide and twinning elements. Until recently, only occasional systematic studies of the deformation characteristics of non-metals have been made; and investigations of the forces necessary to initiate plastic deformation and the factors which affect the flow characteristics have been restricted largely to studies of sodium chloride'-7 , magnesium oxides-l3 and lithium fluoride. 14-22 Fracture studies on alkali halide and metal oxide single crystals have been limited despite the fact that these materials have a number of advantages for fracture studies. Because they are transparent, the cracks which form can be viewed in three dimensions instead of in two dimensions as in metals. Also, they exhibit stress birefringence under polarized illumination, which enables the internal stress pattern and, therefore, the distribution of dislocations to be examined in the vicinity of the fracture. Early workers1-4 have shown that ionic crystals with a cubic structure fracture in tension along the (100) plane normal to the applied stress. These fractures were brittle at room temperature and propagated very rapidly across the cross section of the crystal. More recently, Stokes, Johnston, and Lil0 have studied crack formation in compressed magnesium-oxide single crystals. They found that the cracks, which were observed after about 3 pct strain, formed in the region of a kink band and lay on conjugate (110) slip planes instead of the usual(100) cleavage plane. Two different types of cracks were noted: stroh23 and secondary. The Stroh cracks did not exist merely on the surface but extended through the specimen in the form of tiny slits. A secondary

Jan 1, 1962

By W. A. Griffith

The fundamental principles and modern techniques of experimental planning and data analysis, applicable to any type of research, are particularly important in flotation experimentation. Since they constitute the modern science of experimentation, they should be among the working tools of any scientist, research engineer, or plant operator engaged in flotation investigates. This chapter is a review of these principles and techniques. Equipment and procedures for the actual conduct of experiments will not be discussed here since these subjects are well covered elsewhere in this volume. Neither will any attempt be made to impart a working knowledge of statistical methods of data analysis since this would be impossible in the space allotted, and many excellent texts are available to the diligent inestigator.1-4 The objective here is simply to interest the reader in the application of statistical techniques to flotation experimentation by illustrating their utility in situations frequently encountered, and to point out the principles of experimental planning necessary for their proper use. Any conscientious metallurgist engaged in flotation experimentation or operations is well aware of the inherent complexity of the flotation process, and of the often frustrating difficulties this introduces into experimentation. The raw materials normally treated by the process are complex both physi- cally and chemically, and often highly variable even when from the same source. The flotation process itself is characterized by a very large number of potentially important process variables. Many of these are beyond the con- trol of the metallurgist, and some cannot even be measured quantitatively with available instruments. Those which can be measured and controlled with reasonable precision often produce effects which are intricately interrelated. Not only are the variables many, but the physical and chemical mechanisms by which they function are imperfectly under stood. To compound the difficulty, experimental techniques are relatively crude. Controls are not very precise, and the human factor looms large in most flotation experiments. These situations lead inevitably to experimental data of a relatively low degree of precision or reproducibility. Some are inclined to think that these conditions are unique to flotation experimentation. They are not. The experimental problems met by the agronomist, the biologist, the social scientist, and others are equally complex. Investigators in these fields pioneered in the development of methods for handling just such situations by proper experimental planning and the application of statistical methods in the analysis of data. Their pioneering work has grown into a well established modern science of experimentation which has spread into every field of science. This science is based upon statistical

Jan 1, 1962

By F. L. Ruhlman, Max C. Eastman

The termination of the recent war marked a major changc in the oil-field operations at. Elk Hills. Production was greatly curtailed, various experimental production projects were started, and a long-range exploratory program was inaugurated. Production was reduced from the wartime peak of 65,000 bbl per day to the current rate of about 8ooo bbl per day in order to maintain an available source of crude that can be drawn upon during a national emergency. The existing production rate is deemed essential to carry on the experimental production projects. These projects are being conducted to determine the best methods and means of maintaining the Reserve, shut in, but in a state of readiness to produce the maximum quantity of oil in the most expeditious manner. Projects now being investigated include: (I) protection of surface equipmerit; (2) repair of wells that might damage the reservoir; (3) gas injection; (4) water eneroachment, (5) gravity drainage. An exploratory program is being carried on to determine the amount of recoverable oil in the unexplored portions of the Reserve. The Shallow-zone exploration is practically completed, but owing to the complexity of the Stevens structure and the magnitude of the oil discoveries in the Stevens, exploration will probably continue in that zone for another two years. Introduction Summary of Development History of Elk Hills Although a detailed history of Elk Hills oil field is presented in various publications,1,2 a summary of its unusual development and production history will be given in order that the present problems may be more readily understood. The first development that resulted in commercial production was in the central part of the Reserve. The first well, Hay No. I, in sec 36-R,* was completed in January I9I9, and was soon followed by 37 Others in the same general area. It is commonly referred to as the Hay-Carman area and was shut in in stages from 1925 to 1934 as a result of litigation regarding the title to the land. Not being highly producti,, only about 6½ million barrels of oil with a large volume of gas was produced from the area prior to the shutdown. Shortly after the start of the development of the Hay-Carman area, drilling was started 6 miles east in sec 36-S' Tupman NO. I came in for 5000 bbl per day early in I92o, It was followed by more than 200 others in the next few years, and the field became one of major importance. Produc-

Jan 1, 1949

By B. L. Averbach, M. Cohen

THE PROBLEM MANY hardened steels contain significant quantities of retained austenite even in cases where the carbon and alloy contents are low. In fact austenite has been detected in plain carbon steels containing as little as 0.50 pct carbon.1 Although the austenite may not be visible metallographically it causes definite dilatometric and magnetic effects during subsequent tempering or subatmospheric cooling.1,2,3 Therefore if the reactions which hardened steels undergo during later treatment are to be understood in quantitative fashion it is most essential to have some kind of absolute analysis for the austenite content in hardened steels. Once this analysis has been made, the austenite transformations can be followed precisely by observing such sensitive phenomena as changes in length or in magnetization but the latter techniques can only determine differences in the amount of retained austenite and usually an independent method must be found to put these differences on an absolute basis. In certain instances the microscope can be used advantageously to determine the percentage of retained austenite. The quenched sample is tempered to "darken" the martensite with minimum decomposition of the coexisting austenite, and then is polished and etched in the usual fashion. If the austenite is clearly distinguishable from the tempered martensite and other possible constituents its volume percentage can be measured quantitatively by point counting or lineal analysis.4 Such microscopic methods, however, depend on the etch being sufficiently discriminatory. In fairly coarse structures, if the austenite content is greater than 10-15 pct, there is probably little smearing of the etch, and point counting or lineal analysis seems to be quite accurate. On the other hand if the structure is difficult to resolve, as in commercially treated fine-grained steels which contain less than 10-15 pct retained austenite, the latter may be completely obliterated by the dark etching martensite or it may appear disproportionately low as the interfaces between the two constituents become difficult to distinguish. Another disadvantage of the metallographic method is the need for "darkening" the martensite and hence the determination cannot be applied to as-hardened steels. The required tempering may spoil the structure for other tests or may even remove a small part of the austenite which is being sought. X ray methods hold more promise for covering the range under 15 pct retained austenite. Although austenite and martensite in the hardened steel may be chemically identical, their crystal structures and lattice parameters differ, and the intensity of an austenite diffraction line is some continuous function of the percentage of re-

Jan 1, 1948

By A. J. Shaler, J. Prieto Isaza, J. Wulff

Tantalum metal has a number of unique properties which give it widespread application in modern technology and in research. In electronic apparatus involwing high temperatures in vacuo some of the refractory metals 6ecome brittle. Tantalum retains its ductility at elevated temperatures, and this property, together with its low vapor pressure and its ability to absorb gases, make it important in this field. Its chemical inertness in the presence of acids, halogens, and other corrosive media, makes it useful in chemical apparatus and in neuro and orthopedic surgical applications. As an addition to tungsten carbide in steel-cutting grades of cemented-carbide tools, the carbides of tantalum and of its sister element colum-bium have found considerable use. The present-day method1 of manufacturing tantalum is to sinter a powder compact of the metal in vacuo. Because tantalum-columbium alloys are difficult to work and since tantalum ores almost always contain columbium, the two metals must be separated chemically, the products of the separation being generally in the form of potassium tantalum fluoride and potassium columbium oxyfluoride. These salts are used in fused-salt electrolytic baths from which coarse metallic powder is deposited as a sponge at the cathode. Finer powder can be made from the coarse product or from tantalum scrap by first submitting it to an embrittling heat treatment in hydrogen and then crushing it. The fine hydrogen-containing powder may subsequently be degassed in vacuo at a high temperature. Prompted by the success of others2,3 in the magnesium reduction of titanium and zirconium halides; one of the authors undertook4 an investigation of the thermochemistry of the reaction between solid magnesium and gaseous tantalum penta-chloride, a subject which had not previously been studied. He found that the heat of formation of tantalum pentachloride is approximately 364,250 cal per mol at temperatures lower than the melting point of magnesium. A value of 83 units was found for the standard entropy at these temperatures. With these values, it was shown that magnesium and tantalum pentachloride are capable of reacting exo-thermically at temperatures less than the melting point of magnesium, and that no great violence is to be expected when these substances are heated together. The exothermic nature of the reaction indicated that the Drocess should be efficient and should not require much externally applied energy. Tantalum pentachloride is not commonly made commercially, and any process using it therefore involves the subsidiary problem of producing and handling this substance. A series of experiments was carried out in which dried chlorine saturated with carbon tetrachloride was passed over heated tanta-

Jan 1, 1949

By Helmut Thielsch

MeTallographic specimens whose surfaces are to be investigated are too thick to allow either light or electrons to pass through them for microexamination by transmission. This difficulty is overcome with optical microscopes by illuminating the surface through the objective lens. For electron microscopes best results are obtained by preparing thin replicas of the surface of the specimen, placing them in the microscope and passing the electron beam through them. Since electron microscopes represent a rather recent invention, they have found little application as compared with optical microscopes. This is true because, aside from the cost of new equipment and development of new techniques, some of the older replica methods necessitated the destruction of the surface from which a thin transparent replica was obtained. In other processes in which the surface is preserved, either too tedious a procedure is required, unsuited to "mass-production" requirements of industrial laboratories, or replicas of insufficient contrast and sharpness are produced. In general, investigations with the electron microscope involve five steps: (I) polishing the surface of the metal specimen, (2) proper etching of the surface, (3) preparing the suitable replica from the surface, (4) examination and phorography in electron microscope and (5) interpretation. Preparation of Metal Surfaces Usual metallographic polishing is generclly satisfactory. It is important though that the final polish be applied very carefully, since otherwise evidence of a small amount of deformation might show up even on relatively deeply etched surfaces. A high-power microscope should be used to determine the suitability of the polish and etch. This, of course, is not different from optical examinations, but in these, if a deep etch is used, the problem is less serious. It is frequently difficult to detect with optical microscopes poor polishing aside fiom superficial scratches before etching. Figs. I and 2 show micrographs of "well" and "poorly" polished nickel etched by immersing the sample for 20 min. in a solution containing 8 grams cupric sulphate in 40 C.C. of concentrated HCl and 40 C.C. of Hz0 (Marble's reagent). The sample shown in Fig. I was polished in its final stages for 5 min. on a carborundum wheel followed by ro min. on a rouge wheel, whereas the sample shown in Fig. 2 was polished only I min. on the rouge wheel. Generally, this procedure does not guarantee that the surface of the specimen will be either undistorted or deformed. It was applied here merely to show the effects Of good and poor polishing. To the experienced investigator, plastic deformation is

Jan 1, 1946

By Helmut Thielsch

MeTallographic specimens whose surfaces are to be investigated are too thick to allow either light or electrons to pass through them for microexamination by transmission. This difficulty is overcome with optical microscopes by illuminating the surface through the objective lens. For electron microscopes best results are obtained by preparing thin replicas of the surface of the specimen, placing them in the microscope and passing the electron beam through them. Since electron microscopes represent a rather recent invention, they have found little application as compared with optical microscopes. This is true because, aside from the cost of new equipment and development of new techniques, some of the older replica methods necessitated the destruction of the surface from which a thin transparent replica was obtained. In other processes in which the surface is preserved, either too tedious a procedure is required, unsuited to "mass-production" requirements of industrial laboratories, or replicas of insufficient contrast and sharpness are produced. In general, investigations with the electron microscope involve five steps: (I) polishing the surface of the metal specimen, (2) proper etching of the surface, (3) preparing the suitable replica from the surface, (4) examination and phorography in electron microscope and (5) interpretation. Preparation of Metal Surfaces Usual metallographic polishing is generclly satisfactory. It is important though that the final polish be applied very carefully, since otherwise evidence of a small amount of deformation might show up even on relatively deeply etched surfaces. A high-power microscope should be used to determine the suitability of the polish and etch. This, of course, is not different from optical examinations, but in these, if a deep etch is used, the problem is less serious. It is frequently difficult to detect with optical microscopes poor polishing aside fiom superficial scratches before etching. Figs. I and 2 show micrographs of "well" and "poorly" polished nickel etched by immersing the sample for 20 min. in a solution containing 8 grams cupric sulphate in 40 C.C. of concentrated HCl and 40 C.C. of Hz0 (Marble's reagent). The sample shown in Fig. I was polished in its final stages for 5 min. on a carborundum wheel followed by ro min. on a rouge wheel, whereas the sample shown in Fig. 2 was polished only I min. on the rouge wheel. Generally, this procedure does not guarantee that the surface of the specimen will be either undistorted or deformed. It was applied here merely to show the effects Of good and poor polishing. To the experienced investigator, plastic deformation is

Jan 1, 1946

James Douglas will long be remembered as a distinguished mining engineer and metallurgist, as a scientist with broad vision, as an executive whose understanding of practical problems coupled with his knowledge of men and affairs enabled him to weld together great mining interests and to their service build railroads and bring power. More, he will be recalled as a philosopher and a writer of charm, a historian of no mean order, and one whose catholic tastes and enthusiasms led him into the fields of education, medicine and theology. His aim was to possess that which he considered made life worth while—friends and effectiveness in whatever task he undertook. In this aim he was successful to a degree exceeded by few, as thousands of his friends and associates could and can testify. Dr. Douglas was born on November 4,1837, at Quebec, Canada. His father, James Douglas, Sr., was a prominent physician and the leading surgeon of Canada. He also established the first retreat for the insane in the Dominion, the Quebec Lunatic Asylum, to which he devoted his services for years; The son followed in the footsteps of his father and studied medicine, not only in Canada but also in Scotland and in Germany. He entered the University of Edinburgh in 1855 but after two years at that institution returned to Canada and was graduated from Queens university at Kingston, Ontario, .with the degree of Bachelor of Arts. Later he went to Lava1 University, Quebec, and subsequently became professor of chemistry at Morrin College, Quebec. After he was graduated—at the time he considered his formal education completed—he traveled with his father in Europe and in the Orient; visiting Egypt, being especially interested in that country, several times. They gathered together an important archaeological collection which later was donated by them to the Metropolitan Museum of Art in the city of New York. James Douglas was also greatly interested in photography, a hobby in which he made use of his chemical knowledge. The writer can remember distinctly the descriptions he gave more than forty years ago in Arizona of the difficulties he encountered with the old wet photographic plates, especially while traveling in Egypt, when he prepared and used his own chemicals. In his humorous manner he told how he once discovered, in the nick of time, the nurse preparing to give the baby in the party a rub-down, using for that purpose the white, limpid

Jan 1, 1934

By C. Ernest Birchenall

AS a basis for further progress in several branches of metallurgy, particularly the study of physical properties of solid solutions and the kinetics of solid-solid reactions, a more complete understanding of the structure of solid solutions and the nature of the metallic bond is- necessary. Any investigation contributing to this understanding should be of primary interest to the metallurgist. Since the metallic bond is characteristic of an assemblage of atoms, it can be studied only where this assemblage exists. One of the most promising approaches to this study of the interactions in metals is through the general problem of binary metallic solutions. Although crystal structures of many solid metallic solutions have been determined and solubility limits for many systems are given in phase diagram studies, progress beyond this is irregular. Electromotive force and vapor pressure determinations have provided thermodynamic activity data for small concentration and temperature ranges in the amalgams and a few other systems.' In two systems, however, copper-zinc and iron-carbon, data are available for the calculation of activities over wide ranges of temperature and concentration. This activity data for the brass system is summarized in the preceding paper.= A detailed study of the solubility and distribution of carbon in iron is given by Smith and Darken.3 Their treatment of interaction energies is applicable only to dilute interstitial solutions. The objectives here will be to derive from activity gats given in the previous paper for the brasses and structural considerations as much new and detailed information as possible about the interactions between copper and zinc in metallic solid solution and the effect of these interactions in determining the short range structure of the equilibrium phases; that is, we shall investigate the energy of interaction between pairs of atoms of the same and different kinds, the deviations of the distribution of nearest neighbors from complete randomness, and show that the conclusions found are consistent with the observed behavior of the brass system. The method of treatment is fairly general for substitutional metallic solid solutions and will be applied to other systems. The determination of vapor pressures of the components of alloy systems is being undertaken in this laboratory to supply more data for this purpose. The information obtained from solid solutions may be extended by careful analogy to liquids as long as the metallic type of bonding is preserved. Since it will be necessary to employ the language of thermodynamics, a brief summary defining the terms used extensively in solution theory is given below. Solution Theory4 An ideal solution is one in which the vapor pressure of the constituent molecules

Jan 1, 1947