Search Documents

Jan 1, 1958

By E. G. SINCLAIR

DRILLING wildcat wells in Wyoming differs a little from methods used in any other field. Here it is always advisable to start the hole as large as is convenient in order to carry each string of pipe as far as possible, so that drilling can be continued a thousand feet deeper if necessary, as there is always sand a few hundred feet ahead that really ought to be tested. This plan may seem ambitious, but if it is adhered to, it will save a great deal of trouble before the well is completed. In making the location, one representative from the operating department and one from the geological department should work together, so that the well may be in the best possible place for obtaining oil and the most feasible place to drill for the operating department. In Wyoming nearly all wells are drilled with standard tools, as with them a better log can be kept and better time made in completing the hole. The shales of Wyoming are very hard and do not mix well in a wet hole. The shale cuts into large pieces, too large to be circulated out of the hole, and forms a mat on the rotary which soon cuts off circulation. Then if this mat cannot be jarred from the bit, the drilling string has to be pulled and the mat cut off from the bit with a pick or an axe. I have seen standard tools come out of a wet hole with 10 to 16 in. of mat on the bottom of the bit. Rotary tools have drilled wells satisfactorily in the Big Muddy field and at Billy Creek, but in the other fields the wells have been drilled much more economically with cable tools.

Jan 1, 1926

By H. S. Gipson

A process that has come to be known locally as "multistage stabilization" has been developed in the Haft Kel field of the Anglo-Iranian Oil Co. in southwest Iran, for the recovery of casinghead gasoline. It consists in releasing the dissolved gases from the crude by stages, a practice common in many fields, but which, so far as is known, has nowhere been carried to the extent to which it is employed in Iran. It has been in use there for nearly nine years, during which time some 200 million barrels of crude have been handled by the process. This process of gasoline retention consists in preventing the greater part of the casinghead gasoline hydrocarbons (the butanes and pentanes) from ever leaving the crude, instead of allowing them to be vaporized and then recovered from the lighter gases by the usual compression or absorption processes. Its efficiency is fully equal to that obtained by the absorption process; its disadvantage is that it increases the quantities of ethane and propane in the crude sent to the refinery, but with the growing demand for propane this drawback is vanishing. When casinghead gasoline is recovered as a separate liquid in the Iranian fields, it is blended with the crude, as the only outlet is through the refinery, and the crude-oil pipe line offers the cheapest means of transportation. It is under these conditions that the retention of the butanes and pentanes in the crude by multistage stabilization is a most attractive process, possessing as it does the following advantages: (1) extreme simplicity, (2) low first cost, (3) easy installation! (4) practically 100 per cent operating-time efficiency, (5) no operators required, (6) no water or other services required, (7) negligible maintenance, (8) once established, very little routine testing is necessary. The one essential for reasonably efficient multistage stabilization is that the flowing pressures of the wells should be relatively high; i.e., they should not be less than about one-third the saturation pressure of the crude in the reservoir. This is a very general statement, of course, and much depends on the type of crude and its temperature.

Jan 1, 1940

By H. S. Gipson

A process that has come to be known locally as "multistage stabilization" has been developed in the Haft Kel field of the Anglo-Iranian Oil Co. in southwest Iran, for the recovery of casinghead gasoline. It consists in releasing the dissolved gases from the crude by stages, a practice common in many fields, but which, so far as is known, has nowhere been carried to the extent to which it is employed in Iran. It has been in use there for nearly nine years, during which time some 200 million barrels of crude have been handled by the process. This process of gasoline retention consists in preventing the greater part of the casinghead gasoline hydrocarbons (the butanes and pentanes) from ever leaving the crude, instead of allowing them to be vaporized and then recovered from the lighter gases by the usual compression or absorption processes. Its efficiency is fully equal to that obtained by the absorption process; its disadvantage is that it increases the quantities of ethane and propane in the crude sent to the refinery, but with the growing demand for propane this drawback is vanishing. When casinghead gasoline is recovered as a separate liquid in the Iranian fields, it is blended with the crude, as the only outlet is through the refinery, and the crude-oil pipe line offers the cheapest means of transportation. It is under these conditions that the retention of the butanes and pentanes in the crude by multistage stabilization is a most attractive process, possessing as it does the following advantages: (1) extreme simplicity, (2) low first cost, (3) easy installation! (4) practically 100 per cent operating-time efficiency, (5) no operators required, (6) no water or other services required, (7) negligible maintenance, (8) once established, very little routine testing is necessary. The one essential for reasonably efficient multistage stabilization is that the flowing pressures of the wells should be relatively high; i.e., they should not be less than about one-third the saturation pressure of the crude in the reservoir. This is a very general statement, of course, and much depends on the type of crude and its temperature.

Jan 1, 1940

By R. L. Bell, T. G. Langdon

A technique was developed- for determining the grain strain, and hence the grain boundary sliding contribution, occurring during the high- temperature creep of a magnesium alloy, from the distortion of a grid photographically printed on the specimen surface. The results were compared with those obtained from measurements of grain shape, both at the surface and interrwlly, and it was concluded that the grain shape technique may substantially underestimate the grain strain and overestimate the sliding contribution due to the tendency for migration to spheroidize the grains. ALTHOUGH a considerable volume of work has been published on the role of grain boundary sliding in high-temperature creep, many of the estimates of Egb (the contribution of grain boundary sliding to the total strain) have been in error due to the use of incorrect formulas or inadequate averaging procedures.' One of the most easy and convenient measurements from which to compute Egb is that of v, the step normal to the surface where a grain boundary is incident. Unfortunately, this parameter is also the one associated with the treatest number of pitfalls. Values of v have been used to calculate Egb from the equation: egb =knrVr [1] where k is a geometrical averaging factor, n is the number of grains per unit length before deformation, v is the average value of v, and the subscript ,r denotes the procedure of averaging along a number of randomly directed lines. If the dependence of sliding on stress were assumed, it would be possible, in principle, to calculate k from the known distribution of angles between boundaries and the surface. This in itself is difficult because the distribution depends on the history of the surface,' but the problem is even further complicated by the fact that v depends on other factors such as the unbalanced pressure from subsurface grains.3 However, the great simplicity of the measurement procedure for v makes it highly desirable that this problem of k determination should be overcome. In the present experiments, this was achieved by the use of an indirect empirical method in which the grain strain, eg, at the surface was determined by the use of a photographically printed grid. The assumption here is that the total strain, et, is simply the sum of that due to grain boundary sliding, egb, and that due to slip or other processes within the grains, eg. SO that: Et = Eg + Egb [2] Thus k is given by: In practice, it is customary to indicate the importance of sliding by expressing it as a percentage of the total creep strain; this quantity is termed y (= 100Egb/Et). The determination of Eg from a printed grid within the grains avoids the difficulties due to boundary migration which should be considered when the grain strain is calculated from measurements of the average grain shape before and after deformation. As first pointed out by Rachinger,4,5 however, this latter technique has the particular advantage that it can also be applied in the interior of a polycrystal. Recently, several workers have produced evidence on a variety of materials6-'' to support the observation, first made by Rachinger on aluminum,4,5 that 7 can be very high, 70 to 100 pct, in the interior, even when the surface value, determined from boundary offsets, is very much lower.10'11 Although there have been criticisms both of the shortcomings of the grain shape technique'' and of the different procedures used to determine y at the surface,' it seemed important to check whether measurements of sliding by grain shape gave values of y which were truly representative of the material. In the present experiments, grain shape measurements were therefore made both at the surface and in the interior for comparison with one another and with the independent measurements of grain strain using the surface grid technique. EXPERIMENTAL TECHNIQUES The material used in this investigation was Magnox AL80, a Mg-0.78 wt pct A1 alloy supplied by Magnesium Elektron Ltd., Manchester. Tensile specimens, about 7 cm in length, were prepared from a 1.27-cm-diam rod, with two parallel longitudinal flat faces each approximately 3 cm in length. The specimens were annealed for 2 hr in an oxygen-free capsule, at temperatures in the range 430° to 540°C, to give varying grain sizes, and, prior to testing, the grain size of each was carefully determined using the linear intercept method. This revealed that the grains were elongated -0.5 to 5 pct in the longitudinal direction. Testing was carried out in Dennison Model T47E machines under constant load at temperatures in the range 150" to 300°C. At temperatures of 200°C and below, tests were conducted in air with the polished flat faces coated with a thin film of silicone oil to prevent oxidation; at higher temperatures, an argon atmosphere was used. To determine v,, each test was interrupted at regular increments of strain and the specimen removed from the machine. At the lower strains, when v, was less than about 1 pm, measurements were taken on a Zeiss Linnik interference microscope;

Jan 1, 1969

By Lo-Ching Chang, K. M. Goldman

The kinetics and mechanism of transfer of a constituent across a slag-metal interface are fundamentally important because many metallurgical processes involve the existence of a slag phase and a metal phase. Industrial processes seldom proceed to equilibrium, and information of the rates and modes of reactions are therefore often of greater practical importance than equilibrium data. A study of the kinetics of sulphur transfer across a slag-metal interface under reducing conditions will contribute a great deal toward a better understanding of desulphurization in the blast furnace process. The general principles existing in the transfer of a constituent, such as sulphur, across a slag-metal interface can be extended to similar transfer phenomena in other metallurgical processes. The present paper will demonstrate how such studies will lead to fruitful results from both the practical and theoretical standpoints. EXPERIMENTAL METHOD The apparatus used was, simple. A graphite crucible 15/8-in. id, a wall 1/8-in. thick, and a depth of 4 in., was packed in an outer fused silica tube with powdered magnesia. The crucible assembly was rotated at a speed of 235 rpm inside an in- duction coil. A charge of 250 g of Armco ingot iron was introduced into the graphite crucible and melted by induction heating. The melt was held at a desired temperature for 3-5 "'in., aftcr which 7.5 g of granular ferrous sulphide was added and the bath was held for another 3-5 mi11. A metal sample was then taken by means of a fused silica tube and a rubber suction bulb. Immediately after the metal sample was taken, 30 g of a prefused and crushed slag were introduced. The slag reached the ternperature of the furnace in 1 to 1 1/2 min. Slag

Jan 1, 1949

By K. M. Goldman, Lo-Ching Chang

The kinetics and mechanism of transfer of a constituent across a slag-metal interface are fundamentally important because many metallurgical processes involve the existence of a slag phase and a metal phase. Industrial processes seldom proceed to equilibrium, and information of the rates and modes of reactions are therefore often of greater practical importance than equilibrium data. A study of the kinetics of sulphur transfer across a slag-metal interface under reducing conditions will contribute a great deal toward a better understanding of desulphurization in the blast furnace process. The general principles existing in the transfer of a constituent, such as sulphur, across a slag-metal interface can be extended to similar transfer phenomena in other metallurgical processes. The present paper will demonstrate how such studies will lead to fruitful results from both the practical and theoretical standpoints. EXPERIMENTAL METHOD The apparatus used was, simple. A graphite crucible 15/8-in. id, a wall 1/8-in. thick, and a depth of 4 in., was packed in an outer fused silica tube with powdered magnesia. The crucible assembly was rotated at a speed of 235 rpm inside an in- duction coil. A charge of 250 g of Armco ingot iron was introduced into the graphite crucible and melted by induction heating. The melt was held at a desired temperature for 3-5 "'in., aftcr which 7.5 g of granular ferrous sulphide was added and the bath was held for another 3-5 mi11. A metal sample was then taken by means of a fused silica tube and a rubber suction bulb. Immediately after the metal sample was taken, 30 g of a prefused and crushed slag were introduced. The slag reached the ternperature of the furnace in 1 to 1 1/2 min. Slag

Jan 1, 1949

By Albert Sauveur

To understand this paper properly, the reader must have a clear conception of what is meant by the " critical points " of iron and steel; * and in order to avoid the necessity of tedious references to previous publications on the part of those unfamiliar with the subject, it is here briefly recapitulated. Critictl Points.—If a piece of steel containing, say, 0.50 per cent. or more of carbon, be heated to a high temperature and then allowed to cool slowly, the cooling proceeds at first at a uniformly retarded rate until a temperature of about 700° C. is reached, when there is a sudden " retardation " in the fall of

Jan 1, 1897

By Frank W. Clinard, Oleg D. Sherby

The effect of multiple an transformations on diffusion in a dilute iron alloy was studied. Inter-penetration between iron and an Fe-Co alloy was evaluated, under thermal-cycling conditions chosen so as to transform only the iron-rich side of the diffusion couple. It is shown that a small but consistent diffusion enhancement by a factor of two results when data from the transforming side of thermally cycled specimens are compared with predicted inter diffusion coefficients based on isothermal data. No enhancement is found when data from the mntransforming side of such couples are compared with predicted diffusivities. It is suggested that short-circuiting by moving pain boundaries is the most likely mechanism contributing to the observed diffusion enhancement from multiple phase transJormations in iron. Transformation-induced Point defects, dislocation-pifie short-circuiting, and point defects generated by dislocation motion are less effective in contributing to enhanced diffusion under the experimental conditions utilized. SO far as is known, no studies have been made of the effect of allotropic transformation on diffusion. previous to this investigation. Studies have been made, however, of the influence of transformation on the diffusion-controlled processes of spheroidization and sintering. Cullen1 has described a method of accelerating spheroidization in an AISI 1030 steel. Partial transformation between a and ? phases was uti-

Jan 1, 1965

By R. H. McLean

Velocity, kinetic energy and shear in crossflow beneath three-cone jet bits may influence cleaning of the bottom of the borehole and the teeth of the bit. Laboratory investigation shows that each of these parameters is a function of the diameter of the borehole and the product of the volume rate of flow and velocity through the nozzles (QVn). Increasing QV, or decreasing the diameter of the borehole increases each parameter. These functions provide means of predicting the magnitude of each parameter and of scaling the cleaning forces. INTRODUCTION In drilling operations using conventional jet-type rock bits, the impinging jels create an important flow mechanism. Called crossflow, this flow mechanism originates in the impact area of the jets, spreads across the bottom of the hole and supplies the principal source of energy to clean the teeth of the bit and most of the bottom.' Besides providing the means of cleaning cuttings from the bit and the hole bottom, crossflow may also have other, less direct, effects on the rate of penetration. The shear stress generated on the bottom by crossflow will inIluence the thickness and permeability of any filter cake of mud solids or crushed material which forms on the bottom.' These factors may affect the rate of penetration. A previous pulblication introduced some fundamental concepts of crossflow.' Crossllow was shown to occur in a thin layer adjacent to the bottom, and to cover the bottom completely. The maximum velocity in the crossflow above any position on the bottom was found to be directly proporlional to the square root of the product of the volume rate of flow and velocity through the nozzles—the jct QV,,—and inversely proportional to the diameter of the borehole. This information indicated that the effectiveness of crossllow in scavenging the bottom can be improved by maximizing the jet QV. The investigation reported herein amplifies the definition of crossflow. Complete velocity profile data above a representative position on the bottom are analyzed. These data better illustrate control of the capacity of crossflow to scavenge the bottom, and also relate shear stress on the bottom to known, controllable parameters. The conclusion reached in the previous publication that maximization of the jet QV. produces the maximunl cleaning beneath current jet bits is unchanged by these new data; rather, it is strcngthened. Data presented here show that the kinetic energy flux above a representative position on the bottom is maximized by maximizing the jet QV. The shear stress on the bottom will also be shown to be maximized in the same manner. Since the functions relating the jet QV. to velocity, shear stress and kinetic energy also involve the diameter of the borehole, means of equating, or scaling, these quantities in different sizes of boreholes will be illustrated. EXPERIMENTAL EQUIPMENT AND TECHNIQUE JET BIT MODEL Data were recorded from the same laboratory model as used in the aforementioned investigation of the flow around a jet bit.' The model consisted of a 43/4-in. three-cone, jet-type rock bit in a smooth, flat-bottomed borehole constructed of lucite. The bit had a shape and nozzle placement closely resembling larger three-cone jet bits commonly used in field operations. Fig. 1 illustrates the impact area on the bottom of a jet from this bit. Details of the orientation of the jets may be found in the previous publication. TECHNIOU'E OF MEASUREMENT Measurements of the crossflow were made by inserting a very small Pitot tube through the bottom of the simulatetl boreholc. Extreme thinness of the layer of crossflow necessitated accurate measurements of the height of the Pitot tube above the bottom to achieve close definition of the velocity profile. A cathetometer, which could be read to the nearest 0.005 cm, was used to make this measurement.

Jan 1, 1966

By John T. Awald

The Bradshaw Mountains of west-central Arizona cover an area of 1600 square miles and contain numerous old mines and prospects. The area has been geochemically sampled on a reconnaissance basis to relate mineralized areas to regional structure and rock types. Copper analyses of stream sediments have been classified and contoured to show the distribution of low and high backgrounds and low, intermediate, and highly anomalous areas. Contoured results are compared to geology and known mines. Several prospecting areas are indicated.

Jan 1, 1972

By R. P. Ehrlich, D. A. Dahlstrom

In the hydrometallurgical circuit, many phase separation steps are usually necessary. Typical steps are pregnant liquor - leach residue separation by counter- current decantation or continuous vacuum filtration, clarification of liquids prior to precipitation, ion exchange or solvent extraction, dewatering of final product, etc. The paper discusses the more recent advances in these areas and considers general operating parameters and cost factors. In addition, emphasis is placed on future needs because of the growing importance and necessity of hydrometallurgical processing of minerals.

Jan 1, 1973

Jan 1, 1967

By L. G. Jones, A. S. Odeh

A theoretical developtment is presented which provides a straightforward method of handling the drawdown analysis for both oil and gas wells flowing at variable rates. In the past our inability to analyze variable-rate drawdowns has been a major obstacle in using them for formation evaluation. This method should permit wider use of these tests in the future. INTRODUCTION Pressure build-up analyses are widely used to obtain reservoir data such as the effective flow capacity of the formation. On the other hand. although pressure drawdowns have been run for a long time, they have not been used extensively to evaluate reservoirs because they are difficult to analyze. One of the difficulties in analyzing pressure drawdowns has been that the theory developed until now has required the test to be run at a constant rate. For both oil and gas wells this is a difficult requirement to satisfy. especially during the early period of a well's life when drawdown tests are usually run. In spite of this limitation, drawdown tests are often run with build-ups as a check. In this paper a theory, which handles the drawdown analysis for variable rates, is presented for both oil and gas wells. Thus, one of the biggest deterrents to running drawdowns is removed, and they should become a much more useful engineering tool in the future. THEORETICAL CONSIDERATIONS 011, RESERVOIRS The general equation used for describing the unsteady-state radial flow of slightly compressible fluids in homogeneous porous media can be written in cylindrical coordinates as where r is the radial distance in cm, t is the time in seconds, p is the pressure at r and t in atmospheres, + is the fractional porosity, p is the viscosity in cp, c is the compressibility in vol/vol/atm, and k is the permeability in darcies. There are a number of solutions of Eq. 1 for various boundary conditions. One of these is the so-called "point-source" solution, which approximates the case of an infinite oil reservoir with a well located at r = 0 and produced at a constant rate. The point-source solution of Eq. 1 is

Jan 1, 1966

By Earle E. Schumacher, W. C. Ellis, John F. Eckel

Copper-calcium alloys are of interest as materials for use in deoxidized conductors of high conductivity. That calcium is effective in deoxidizing and degasifying copper is well known. Brandenberg and Wiensl have described the use of calcium in the casting of sound copper and state that the deoxidation can be carried out without difficulty. The castings that they prepared were sound and sufficiently ductile to permit wire drawing. Pratt,2 in British Patent No. 1699 (1907), has claimed the use of calcium for the deoxidation and degasification of copper. Masing3

Jan 1, 1930

Jan 1, 1897

By A. W. Fahrenwald

THE absolute efficiency of crushing and grinding in a ball mill is not known. A number of investigators have made calculations to this end and have presented efficiency figures. Two factors have prompted further investigation of this subject: (1) the unbelievably low magnitude of the values offered, and (2) a desire to obtain, if possible, true relationships between the relative efficiencies of a ball mill operating under varying conditions. A useful forward step in the study of mill efficiency was made when Martin1 and Gross and Zimmerley2 proved the correctness of Rittinger's law, and incidentally the incorrectness of the so-called Kick law, and when Gross and Zimmerley3 determined and gave surface values for Tyler sieve-sized quartz. These data are probably accurate throughout the range of the sieve scale, but on -400 mesh (which is the finest sieve available), the surface data, as obtained by the hydrofluoric acid disso-lution method, are of doubtful reliability. Any inaccuracy existing in surface determinations of -400-mesh material, especially when comparing runs in which varying quantities of this product are formed, will cause the resulting relative mill efficiency values to be distorted. Moreover, knowing surface accurately, the efficiency calculations require a surface energy figure. Two such figures are to be found in literature, one by Edser4 and one by Martin.5 Edser's surface energy

Jan 1, 1931

By W. J. O'CONNOR

THE production of lead in the United States for the period from 1720 to 1912 was 10,432,668 tons valued at $924,600,000. The average price during this period was 4.4c. a pound, although lead sold at times below 3 cents. We know that in the early days of lead smelting in Montana lead was deliberately lost in the slag and only enough reduced as bullion to collect the silver. This bullion was freighted by ox team to Corinne, Utah, the terminus of the railroad at that time, and shipped to Swansea or Omaha, Neb., for refining. The slag from some of the above mentioned operations contained as much as 15 per cent lead and has since been resmelted. Since 1921 the production of lead has increased each year and the price and tonnage have been as follows :

Jan 1, 1926

Jan 1, 1954

By AIME AIME

FEW men are better known in fuel engineering circles in the Middle West than the present Chairman of the Coal Division of the A.I.M.E. - Julian Elnathan Tobey. Now vice-president in charge of engineering of Appalachian Coals Inc., of Cincinnati, he has served that pioneer regional marketing agency since Aug. 1, 1934, when he became manager of its engineering department. His duties have included field promotion work in the interest of use of the agency's coals from eastern Kentucky and Tennessee, south western Virginia, and southern West Virginia in new plants of all types. He has been especially interested in certain industries which have shown an alarming tendency to change to natural gas or hydroelectric power; also in the development and practical application of small stokers and other mechanical equipment.

Jan 1, 1941