Search Documents

By J. C. Scully, G. Sanderson

The electrolytic formation of y hydride in thin foils of Ti-5Al-Z.5Sn alloy and four Ti-A1 binary alloys has been studied by electron microscopy and electron diffraction. Two orientation relationships have been found: THE adsorption of hydrogen by titanium alloys from aqueous solutions has been widely reported. This can occur, for example, in both alkaline' and acidic2 pickling baths, in chemical polishing374 and electro-polishing Solutions,3,4 during cathodic polarization5" and under certain corrosion conditions,7,8 Etching reagents may also produce visible precipitates, sometimes after an aging period.9 During an investigation into the stress corrosion susceptibility of a titanium alloys by thin foil electron microscopy many observations have been made of hydride precipitation which has been deliberately promoted by techniques that are described below. The characteristics of hydride precipitation are reported and the observed crystallographic orientation relationships are discussed with reference to distortion in the titanium lattice created by the presence of the hydride. EXPERIMENTAL TECHNIQUE One grade of commercial titanium and five alloys were examined. Their composition and hardness values are shown in Table I. All the materials were in the form of thin sheet, 0.05 to 0.065 cm thick, which had been annealed after cold rolling. Foils suitable for transmission electron microscopy were made in two ways: a) by chemical polishing; and b) by elec-tropolishing. The solution used for chemical polishing was a mixture of 44 pct HF and 73 pct HNO3 in the volumetric ratio 2:3. During this polishing specimens were manually moved up and down in the solution. The reaction was veFy rapid, specimens thinning to foil thickness (2000A) in 5 min. Since chemical polishing solutions tend not to cause hydride contamination if they are kept cool3 no attempt was made to prevent the solution from becoming hot during the thinning operation. Electropolishing was performed at -30° C with a mixture3 composed of 295 cu cm methyl alcohol, 175 cu cm n-butyl alcohol, and 30 cu cm perchloric acid with an applied voltage of 40 v after chemically thinning specimens to approximately 0.017 cm thickness in a cool solution of 44 pct HF, 40 vol H2O2, and water in the volumetric ratio 1:6:3. EXPERIMENTAL RESULTS 1) Ti-5A1-2.5Sn Alloy. The Ti-5A1-2.5Sn alloy was severely contaminated by hydrogen during the chemical polishing. Foils obtained in this way contained large amounts of the y hydride phase. A typical micrograph is shown in Fig. l. The laths were identified as the hydride phase by selected-area diffraction of a large number of foils examined in a tilting stage that could be turned through 40 deg. Using the lattice spac-ings of the alloy obtained by X-ray diffraction as a standard the a value of the hydride was determined fromo the electron diffraction patterns to be 4.38 to 4.40A. The accuracy of this figure is only about ±2 pct. Further evidence of the identification was obtained by vacuum annealing chemically polished foils of the alloy at 500°C. This resulted in the dissociation of the hydride with the production of dislocations and possibly vacancy loops as shown in Fig. 2. The hydride

Jan 1, 1968

By D. R. Spink

In the preparation of zirconium and hafnium metals, there are many indications that impurity levels control the physical and chemical properties of the metal. The purpose of this work was to develop methods of producing pure raw materials that could be reduced to highly pure metals. Early work by the Carbomcndum Metals Co. and others indicated that certain fused salts were highly efficient in the removal of impurities from gaseous zirconium tetrachloride. We have developed workable fused salts along with a continuous and higly efficient scrubber design which can be used to produce very pure zirconium tetrachloride. Metal made from the purified tetrachloride has been shown to approach crystal bar metal in purity. Scrubber designs are discussed with recommended materials of construction. VARIOUS methods have been used to purify zirconium (and hafnium) tetrachloride. Most of these methods involve thermal degassing initially (the removal of more volatile compounds at temperatures below that where zirconium tetrachloride exhibits a significant vapor pressure) followed by a sublimation step (which conveniently leaves the nonvolatiles behind.) While these procedures effect definite purification, such processing is batchwise and does not result in optimum purification. Early work by The Carborundum Metals Co. and others indicated that fused salts were highly efficient in the removal of impurities from gaseous zirconium tetrachloride. The objective of this work was to develop a continuous fused-salt scrubbing process that would yield high-purity zirconium and hafnium tetrachlorides. The term "fused salt" refers to the molten state of ionic compounds and as used here, specifically refers to alkali metal and alkaline earth halides. Fused salts, because of their many valuable properties, are becoming increasingly im- portant industrially. These valuable properties of the fused salts are: 1) stability at elevated temperatures; 2)low vapor pressure; 3) low viscosity; 4) ability to dissolve many different materials; and 5) good elctctrical conductivity. All but the last property enhances the use of fused salts as scrubbing agents for zirconium and hafnium tetrachlorides. Fused-salt scrubbing may be defined for our purpose as the intimate contact between a gaseous compound and a molten salt with the purpose of removing impurities from the gaseous compound. In this case, the gaseous compound is zirconium tetrachloride which submlimes at 331°C. When this gas is contacted with a molten salt, impurities such as aluminum, iron, and titanium are removed and the resulting product is considered fused-salt scrubbed. Zirconium and hafnium are sold to a purity specification. Generally speaking, normal production without scrubbing is capable of meeting specifications. There are, however, several considerations That make the knowledge of methods of additional purification highly desirable. These are: 1) the control of product analysis; 2) the production of a pure product for special applications; 3) the salvaging of off-specification material; and 4) the use of raw materials with higher impurity levels than 1 he present raw materials. You will note that items 1 and 2 are somewhat complementary to each other and that item 4 assumes that The present process has impurity removal limitations. To better understand the part that fused-salt scrubbing of zirconium tetrachloride plays in the manufacture of zirconium, Fig. 1 contains an illustrated flow sheet of the industrial production of zirconium metal. In referring to Fig. 1, we can point out the specific benefits derived from our ability to purify zirconium tetrachloride. Purification of the crude (hafnium-containing) zirconium

Jan 1, 1962

By D. E. Musgrove

The question of alternating current vs direct current has become an important consideration to the mining industry. Rising production costs demand lower investment, which, in many instances, can be realized by the use of ac mining machines. Generally ac motors, control systems, and distribution and power conversion equipment can be installed for approximately 50 pct of the first cost of their dc equivalents. This basic saving has made ac mining a serious competitor for the traditional dc mining systems. With the increased use of ac voltages underground, there has developed the problem of conveniently converting distribution voltages to usable 480-v power. Power at low voltages should not be carried for comparatively long distances, and the transformation should be made at the point of use. Otherwise, serious voltage regulation problems and objectionable line losses will occur.

Jan 5, 1955

By Brij M. Moudgil

Disposal of fine coal refuse is one of the major technical problems which could adversely affect growth and development of the coal industry. At present one of the most: common methods for disposal of fine coal refuse slurry involves impounding the slurry behind dams. However meeting new federal and state government regulations for building, maintaining and reclaiming these impoundments in addition to terrain and space considerations render this technique to be only marginally competitive with other disposal methods. The coal industry has been actively engaged in developing alternate disposal techniques which are economically feasible and environmentally acceptable. A review of coal refuse disposal problem and current refuse disposal practice both in the eastern and western coal fields is presented. Various promising techniques being developed for economical and safe disposal of fine coal refuse slurry are also discussed.

Jan 1, 1980

By Robert Pike

THE first authentic description of an iron bath for the deposition of iron is probably that of Bottger in 1846, who used a bath containing ferrous sulfate and ammonium chloride. In 1861, Kramer deposited iron from ferrous chloride solution. Electrolytic iron was produced in 1.869 by Bietz, who used it for making some magnetic tests. In the same year, Klein is said to have worked out his process. Jacobi1 in 1869 described the results obtained in electroplating with iron on copper for making dies and plates for bank notes, by Klein's process. A letter from Klein to Jacobi describes the bath more fully. It consisted of FeSO4 + (NH4)2S04. Lenz2 described ?some properties of electrolytically precipitated iron. He used Klein's bath, FeSO4 + MgSO4 + MgCO3, to neutralize and obtained fine-grained and hard iron. His conclusions were as follows: 1. Electrolytic iron and copper contain gases, notably hydrogen. 2. The volume of gas absorbed by iron varies within wide limits, but it is easy for iron to take up very considerable quantities of gas. 3. The absorption of gas is principally in the first formed layers of iron. 4. When iron is heated, gas begins to come off below 100°, principally hydrogen. 5. Heated to redness, reduced iron oxidizes in water, in part at least at the expense of the oxygen of the water, decomposing it and setting free hydrogen, which is partly or wholly absorbed. Siemens,3 in 1889, was the first to propose a general process embodying a step for leaching a sulfide mineral with ferric chloride or sulfate and a step for regenerating the leach and depositing iron on a cathode in a diaphragm cell. So far as is known, Siemens did not carry out his patent

Jan 1, 1930

By Stuart Buckley

THE application of hydrocarbon equilibrium data to various problems encountered in refining and in natural gasoline recovery is an old and well established practice. Both generalized data and data on specific hydro-carbon systems have been made available by a number of investigators. More recently such data have been applied to the relations governing the separation of oil and gas both in the reservoir and at the surface. Most of the applications to production problems, however, have been based upon examinations of surface samples of oil and gas. This paper describes a technique that has been used satisfactorily in a number of cases to calculate directly from the hydrocarbon analysis of and auxiliary laboratory data on a subsurface sample of the reservoir fluid the behavior of the oil and gas during the various stages of separation at the surface incident to production.

Jan 1, 1938

By C. W. Phillips, D. N. Frey

A commercial Ti-Fe-Cr alloy, Ti-150, exhibits a martensitic transformation on cooling and two nucleation and growth reactions, one above and one below the Mg-Mf region, on isothermal holding below the single-phase ß temperature range. The reactions were followed by metallographic, X-ray diffraction, and microhardness methods. THE rapidly expanding engineering application of titanium and its alloys makes increasingly urgent an adequate knowledge of the effect of heat treatment on this material. The work herein reported is an attempt to determine certain aspects of the behavior of a commercially available alloy, Ti-150, during heat treatment. The alloy, with a nominal composition of 2.7 pct Cr, 1.3 pct Fe, 0.25 pct 0, 0.02 pct N, and 0.02 pct C, was received in the as-rolled condition as a 3/4 in. round. Slugs 0.11 to 0.12 in. thick were cut under a coolant using a silicon carbide wheel. Preliminary work established that the alloy consists of two phases, a (hexagonal close-packed) and /3 (body-centered cubic), at temperatures below 1750" to 1775"F, and of only /3 phase at higher temperatures. The slugs were heated for 1 hr in air at 1800°F to form a single-phase /3 matrix, then transferred to molten tin (1250° to 1650°F) or lead (1150°F and below) for isothermal holding. Holding temperatures ranged from 700° to 1650°F, times from 0.001 to 23 hr. The treated slugs were then sectioned, one part for metallographic examination and diamond pyramid hardness, the other, after deep etching to remove the high oxygen surface,' for comparative lattice parameter determination and X-ray phase identification. Hardness measurements were taken on the lightly etched surfaces of the metallographic specimens; a 1000 g load on a 136° diamond pyramid was used. Five impressions on each sample were made and the average of the hardness calculated. The use of microhardness measurements to follow the course of an isothermal transformation reaction is undesirable because of the possibility of wide differences in microconstituent hardness.' They were used in this case, however, because of the small amount of material available. At the higher transformation temperatures, where the above-mentioned objection was apparent, the readings were proportioned to correspond to the estimated ratio of transformed and untransformed constituents present. At lower temperatures, resulting in much finer microconstituents, the microhardness measurements were more uniform. The standard deviation of the mean of five impressions calculated from these latter values was 4.2 DPH. Employing 2a limits (probability 0.95) the experimental error of the hardness measurements averages was 8.4 DPH. The etchant used was composed of one part glyc-erol and one part 48 pct hydrofluoric acid." Of a number of etches tried, this one appeared most satisfactory. All micrographs were taken at 500X magnification and with oblique lighting to permit easier identification of the acicular structure resulting from rapid cooling. No advantage was gained by using polarized light for metallographic examination. Phase identification and lattice parameter measurements were made with a North American Philips high angle spectrometer in conjunction with a recording potentiometer. Considerable difficulty was encountered with some of the lattice parameter measurements because of the extreme broadness of the few diffraction lines obtained from samples consisting mainly of strained, untempered, quenched structures.

Jan 1, 1953

By R. Silent, N. A. Rousselot

The first producing wells completed in the Kettleman Hills arca were noteworthy for their high gas-oil ratios. As a result they became the object of criticism, and controversies arose based on their alleged lack of gas conservation. Ultimately protracted hearings ensued in the District Court of the area, and diverse rulings and subsequent modifications have been handed down affecting the permissible gas-oil ratios. When the Kettleman North Dome Association was formed in April, 1931, and the control of the major portion of the North Dome area vested therein, it was decided to produce only those wells which had a relatively low gas-oil ratio. Among the wells having the highest gas-oil ratio were the Milham Elliott No. 1 (the discovery well) and the Continental Elliott 12-8. drilled as an offset to it. Under the numbering system adopted by the Kettleman North Dome Association, these wells are now known as 88-2P and 1-12P, respectively. Milham Elliott No. 1 was originally drilled to 7236 ft., then redrilled to 7108 ft. The upper portion of the Temblor Horizon produces with a very large gas-oil ratio; production which actually consists of light crude oil with an accompanying large.volume of gas. Little was known as to the location of the Temblor formation at that time but it is now generally accepted that its top was encountered at 6180 ft., giving 928 ft. of penetration. Initial production was estimated at 4000 bbl. of oil and 80 to 90 million cubic feet of gas per day, giving a gas-oil ratio in excess of 20,000 cu. ft. of gas per bbl. of oil. This ultimately increased to a ratio of about 48,000 at the time the well was killed when it was producing about 1100 bbl. of oil and 52 million cubic feet of gas, with a flow pressure of 1200 pounds. The Continental Elliott 12-8 was drilled to a depth of 6876 ft. with the top of the Temblor at 6100, giving a penetration of 776 ft. The estimated initial production of this well was 7000 bbl. of oil and 130

Jan 1, 1933

By J. D. Dixon

Procedures are given for calculating stresses in underground tunnel supports which accounts both for the structural behavior of the support and that of the adjacent rock mass. Stresses in the support are caused by service loads and rock reactions. Service loads are due to rock pressures, hydrostatic and hydraulic pressures, selfweight of the support, or other utilitarian-type loads. Rock reactions, equal and opposite those in the support, are due to the deformational interaction that results as service loads deform the tunnel support against the adjacent rock mass. The procedures developed for solving this problem are an application of matrix structural analysis. The principles involved in this method allow for the consideration of the deformable characteristics of most tunnel support systems and an iterative solution procedure is applied to determine the areas of support-rock interaction. Numerical results of example problems are given.

Jan 1, 1972

By L. Michael Kaas

The mineral industries are striving to expand their use of the computer's ability to process exploration, geologic, and mining data. Digital plotting programs and devices are continuing to gain wider use for lowering the cost and the time required to produce many types of maps and cross-sections commonly used by mining companies. Mineral engineers and geologists will soon be using a new tool, computer graphics, to greatly facilitate the use of computers to solve a large number of industry problems. By means of cathode-ray-tube (CRT) displays, an engineer can search large files of geologic data; display elevation contours, geologic structures, and ore grades; construct geologic and mining cross-sections; and compute tonnages for mining plans or ore reserve estimates. Examples of both digital plotting and cathode-ray-tube problem solving approaches are discussed in this paper.

Jan 1, 1969

The problem of applying instrument control of variables associated with lead-zinc ore treatment has been under investigation for several years at The Zinc Corp. facilities in Broken Hill, Australia. In 1959 it was decided that there was sufficient knowledge of the problem to enable specifications to be drawn up for a system to automatically control at set conditions the roll crushing, ball milling, lead flotation and zinc flotation sections. In choosing between electrical and pneumatic control systems the broad principle was adopted that if the sensing system was pneumatic the transmission and control would also be pneumatic, whereas if electrical sensing was employed, electrical transmission and control would apply. In general. pneumatic systems were preferred owing to lack of experience with, and standardization of, the electrical systems offered at the time the specification was prepared.

Jan 12, 1964

By R. M. Douthwaite, G. Birkbeck

The effect of grain size and specimen dimensions on the occurrence and magnitude of a yield point drop in pure iron has been examined. The tests were done at room temperature. The results indicate that gain size is the critical factor determining whether a yield drop occurs. The specimen diameter:gain size ratio does not influence the magnitude of the yield drop for the range of gain size and specimen diameters investigated. HUTCHINSON,' petchY2 and worthington3 have investigated the grain size dependence of the upper yield stress (uUYP) and the yield point drop, ouyp - aLYP, in Armco iron, mild steel, and Si-Fe, respectively. These authors used center-annealed wires to avoid stress concentration from specimen shoulders and to ensure uniformity of the applied stress. Coarsegrained specimens show no yield point drop; the yield point drop then increases as d-'I2 increases (where d is the grain diameter). These results can be understood in terms of Petch's analysis2 in which the magnitude of amp depends on the strain rate in the (limited) number of grains deforming plastically at the upper yield point. If N grains per unit volume are undergoing plastic deformation, the strain rate in the deforming grains is l/Nd3 times higher at the upper yield stress than when the whole specimen deforms homogeneously. If N is constant and independent of grain size at uUyp, then all the grains are deforming when ~d~ = 1, so there is no yield point drop. At finer grain sizes, the yield point drop is given by: where AU, is the friction stress increase corresponding to a tenfold strain rate increase. Christ, Smith, and Burton studied the upper yield point in 0.050-in.-diam wire specimens prepared from zone-refined iron. Each end of the 2; -in. specimens was soldered to a & -in. diam steel ball and the load applied through the two balls. There was a yield point drop in specimens with grain diameters less than 0.1 mm; no drop was observed in specimens of grain diameter greater than 0.1 mm that were free from veining substructure, but specimens of grain diameter 0.129 mm, annealed in the y range, showed an upper yield point. and this was associated with the presence of a veining substructure in these specimens. Christ et al. suggested the upper yield point occurs when more than a specific number of grains fill the specimen cross section so a multiplicity of slip is required to initiate plastic deformation. Table I summarizes the published data on the grain size at which the yield drop disappears. On the basis of this data the ratio of specimen diameter:grain diameter = 5 to 27 appears to be the critical value for the occurrence of a yield point drop. Thus, petch2 interprets the appearance and magnitude of the yield point drop in terms of the limited number of grains deforming plastically at uuyp, whereas Christ et a1. consider that the occurrence of the yield drop depends on the ratio specimen diame-ter:grain diameter. The published data cover a wide variety of materials so some variation between the results is to be expected, but the size range covered in the data of Table I is rather limited. In an attempt to discover whether the specimen diameter:grain size ratio or the grain diameter is critical in determining

Jan 1, 1969

P. L. Pratt (University of Birmingham, Birmingham, England)—The author has measured the hardening effect of isolated edge and screw dislocation boundaries in a remarkably elegant manner, and he proposes that the detailed structure of the boundary determines its effectiveness as a barrier to slip although "there are still unknown details of the distribution which may be extremely important." On p. 678 the author states "that for a good crystal (one having a yield of about 30 psi) a change in annealing temperature from 300" to 400 °C resulted in a negligible shift in the level of the stress-strain curve." Is this in agreement with the results of the earlier paper by Li, Washburn, and Parker8 in which such a change of temperature produced notable hardening in crystals with a yield of about 30 psi? Or were these earlier crystals, of the same nominal purity, less perfect than those used in this work? The experiment illustrated in Fig. 15, p. 681, shows that the boundary has sharpened after annealing at 400 °C, the temperature at which the hardening effect first becomes apparent. Did the author verify that no sharpening of the boundary occurred at, say, 300 °C where no hardening was found? This would seem to be an important check on the proposed mechanism, especially since zinc of this purity should polygonize at temperatures well below 400 °C within the annealing times used here. There seem to be at least two alternative explanations which could fit these facts: 1—The boundary may sharpen at 300 °C or even lower temperatures but be unable to contribute greatly to the hardening until jogged by thermal vacancies and other impurity atoms after 400 °C anneal. This mechan- ism, discussed in the earlier paper,' is believed to account for the thermal hardening observed by Blank'" in NaCl, as stated elsewhere: and by results from recent experiments which tend to confirm this view. 2—The dislocations in the diffuse boundary may be locked by impurity atoms at 300 °C and thus only sharpen the boundary at 400 °C with the aid of thermal vacancies. In this case it would be difficult to distinguish between the two sources of hardening (sharpening or jogging), using metal of this purity. Jack Washburn (author's reply)—The author wishes to thank Dr. Pratt for his discussion. In connection with his first comment, it should be pointed out that the temperature of testing in the present series of experiments was —196°C, whereas, in the earlier experiments he referred to,' it was 20°C. Therefore, the yield values should not be directly compared. It is likely that the crystals used in the present work were initially more perfect macroscopically than the large shear specimens used previously. The small size of the test section in the kink specimens made it possible to select regions of the large crystals, from which they were acid-cut, that were free of observable small angle boundaries. The sharpening of a microscopically diffuse boundary such as that in Fig. 15 begins in zinc of this purity well below 300°C. However, it is probably not justified to conclude that because a boundary looks sharp under the microscope it has attained the ideal structure. The author agrees with Dr. Pratt that jogging of dislocation lines is one of the structural features of a small angle boundary that should be important in determining its strengthening effect. More detailed information concerning the changes in boundary structure as a

Jan 1, 1956

By Max Roesler

Page I. Introduction........................... 78 Location.......................... 78 Scope of Work and Acknowledgments.............. 79 History and Mining...................... 80 I1. Topography and its Interpretation................. 80 III. Petrology............................ 82 Sedimentary Rocks...................... 82 Description....................... 82 Age.......................... 84 Igneous Rocks........................ 85 Diabasic Rocks..................... 86 Dioritic Rocks...................... 87 Granitic Rocks...................... 88 Later Dike Rocks.................... 88 IV. Areal Geology.......................... 88 Rock Types Found in the District............... 88 Distribution of the Various Rock Types............. 89 Surface Distribution................... 89 Vertical Distribution................... 90 Causes of Present Areal and Vertical Distribution of the Various Rock Types..................... 91 Faulting...................... 91 Magmatic Differenti~tion............... 91 Tilting........................ 95 Erosion....................... 96 V. General Description of Ore Deposits................ 96 Nature of Ore ........................ 96 Shap~ and Size of Orebodies.................. 96 Geologic Position....................... 97 Mineralogy......................... 98 Distribution....................... 98 Interpretation...................... 99 Superficial Alteration................... 102 VI. Genesis of the Ore Deposits.................... 104 Previous Theories...................... 104 J. P. Kimball...................... 104

Jan 1, 1917

By D. J. Schmatz

DISCUSSION OF RESULTS The qualitative correlation between low-temperature ductility and prior high-temperature creep strain in nickel obtained in this investigation confirms the result obtained on high-purity brass by Chen and Machlin. However, the quantitative effect is much smaller in nickel. Comparison can be made on the basis of a prior high-temperature strain that is a certain percentage of the total high-temperature elongation to rupture. In the research of Chen and machlin, the prior high-temperature strain of 1/2 pct equaled 8.5 pct of the total high-temperature elongation at rupture. For nickel, in our experiments, 8.5 pct of 21.2 pct equals 1.8 pct. For eh = 1.8 pct, the loss in ductility in percent equals x 100 = b.5 pct. That is, for equivalent bo Formation of Beta Manganese-Type Structure in Iron-Aluminum-Manganese Alloys D. J. Schmatz IRON-aluminum alloys have gained much interest in the past few years for use as a base material for elevated-temperature alloys because of their excel- high-temperature strain the loss in low-temperature ductility is 8.5 pct for nickel as compared to 60 pct for pure a, brass. It is also interesting to note the observation that in nickel the low-temperature fractures, even at the most extreme high-temperature pre-strain, were partly trans crystalline and partly intercrystalline. In the case of a brass, these fractures were completely intercrystalline. According to the data on the percent of the grain boundary area that is cracked, at 22 pct high-temperature elongation, about 12.5 pct of the grain boundary area does not carry load. Thus, the inter-crack areas are carrying a stress that is about 11 pct higher than the nominal stress. A simple model predicts that the overall elongation, which is primarily the elongation in the bulk of the specimen, will correspond to the nominal stress when the stress in the intercrack area equals the tensile strength. Quantitatively this model predicts the equation The form of this equation will agree with that found if the strain-hardening exponent, n, equals unity. Actually this model is too gross an approximation to yield good quantitative results. The question naturally arises as to whether in ordinary hot-working, such as hot-rolling, intercrys-talline cracks are introduced that affect the low-temperature properties. It appears that the answer is that such a possibility cannot be overlooked, if the hot-working induces tensile stresses at temperatures above the equicohesive temperature and if the material tends to be notch sensitive at low temperature. ACKNOWLEDGMENT This research was supported by the Aeronautical Research Laboratory, Directorate of Research, Wright Air Development Center, United States Air Force. REFERENCES lC. Zener: Fracturing of Metals, 1948, Cleveland, ASM. 'H. C. Chang and N. J. Grant: Mechanism of Intercrystalline Fracture. AIME Trans., 1956, voL 8, p. 544; lownal of Metals, May, 1956. 'E. S. Machlin. CreepRupt ure by Vacancy Condensation, AIME Trans., 1956, vol. 8, p. 106; lownd of Metals, February, 1956 'C. Chen and E. S. Machlin: On a Mechanism of High-Temper at ure Inter-crystalline Cracking, lownd of Metals, July. 1957. p. 829. Alloys lent oxidation resistance. Binary alloys of aluminum in iron are ferritic and consequently have poor hot strength. Alloys of iron-aluminum-manganese were made in an attempt to produce an austenitic alloy containing sufficient aluminum to retain the oxidation resistance of binary alloys of iron-alumi-

Jan 1, 1960

By R. E. Holmes, T. W. Leland

The solution to the unsteady-state mass- and heat-transfer equations describing the adsorption of a dilute component from a gas stream flowing through a packed bed is readily applicable to the design of hydrocarbon recovery units. The solution to these equations depends on the assumption of a linear equilibrium equation to relate concentrations on the surface to concentrations in the gas. This assumption is shown to be justifiable for components which are very dilute in the gas stream. This approach permits the prediction of the effects of bed shape and size, cycle time, and gas mass velocity on the recovery of each component. It also allows the time and gas flow rate needed for regeneration to be determined. The equations involve a constant for each component and another constant characterized by the type of adsorbent. These constants must be evaluated from operating data. Values of these constants determined for silica gel are presented. This paper points out the type of experitrrental data needed for a thorough design of hydrocarbon adsorption units. INTRODUCTION The growing importance of adsorption processes to recover hydrocarbons from natural-gas streams has created an urgent need for better methods to design and predict the performance of these processes. Since the original use of solid adsorbents in natural-gas processing was for dehydration, most of the current design methods for hydrocarbon recovery re extensions of those developed earlier for dehydration. These methods are based on an adsorptivity or bed loading factor defined as the amount of a particular component adsorbed per unit weight or per unit volume of the packed bed. The recovery of a given component is then expressed as an empirical function of its adsorptivity on a given adsorbent. In spite of the simplicity and initial utility of these methods, they are not completely satisfactory in that they do not predict the effect of the dimensions of the bed in relation to flow rate and cycle time, and do not predict the distribution of various components along the length of the bed. It is possible, however, to make a considerable improvement in the design of these processes by applying the basic equations of mass and heat transfer applicable to gases containing small concentrations of adsorbing components flowing through granular beds. These equations have been developed and solved by Anzelius,' Furnas,% nd Hougen and Marshall." where G = mass velocity of the inert constituents (assumed to be methane), lb/hr-sq ft, y = weight of an adsorbing component in the gas per unit weight of inert, lb of a given constituent per lb of methane, x = bed length, ft, p, = packed bed density, lb/cu ft, P, = gas density, Ib/cu ft, f = void fraction in the bed, t = time, hours, and w = weight of a given component adsorbed per unit weight of adsorbate free solid, Ib/lb pure adsorbent. The term on the left side of Eq. 1 represents the flow rate per unit bed volume of a component entering less the flow rate per unit bed volume of that component leaving the differential bed length. The terms on the right side represent, respectively, the accumulation rates per unit bed volume on the solid and in the gas phase within the differential bed section. The last term is negligible for this application since pgfv is quite small in comparison with p, and G. The partial differential is determined by the mass-transfer rate between gas and solid in the differential section.

By J. S. Kasper, R. M. Waterstrat, B. F. Decker

THE existence of v phase in the Mn-Mo system was discovered in this laboratory several years ago,' but neither the conditions of its formation nor its composition were known, and preliminary attempts to reproduce the phase were unsuccessful. We wish now to specify the information appropriate to phase formation on the basis of experiments performed since that time. The starting materials were in every case electrolytic manganese and high purity molybdenum. Two methods of preparation were employed: l—arc-melting varying combinations of the elements in an inert atmosphere and subsequent heat treating, and 2—sintering compressed mixtures of finely divided powders of the elements. In the latter method, the powders were first passed through 200 mesh screen and then compressed into cylinders of % in. diameter and % in. length, which were sintered at elevated temperatures in an atmosphere of dry hydrogen. For some samples, the sintering temperature was 1200°C (for 1 hr), and these were then heat- treated at lower temperatures for times up to 24 hr. Eventually it was found, for the proper composition, that essentially pure a phase could be produced by sintering at 1125°C for 3 hr. Quenching to room temperature was effected by means of a stream of cold, dry hydrogen in a water-cooled chamber. The arc-melting procedure was found to be unsatisfactory after an investigation of many samples at different compositions and temperatures. Large quantities of manganese were vaporized during melting and none of the products were homogeneous or contained extended regions of pure phase. Nonetheless, these experiments established that no formation occurs in the Mn-Mo system below 1115oC, and indicated, at least roughly, the composition range of interest for further exploration. The more definite results obtained from samples produced by the second method are given in Table I. A portion of sample 2 heated for 16 hr at 1000°C in a Vycor tube transformed to molybdenum plus unidentified phases of complex X-ray pattern. From these few results it appears that the region of phase is quite narrow in composition. It is of interest that the composition is such as to make for difficulties in correlating this structure on an electron atom basis with other a structures of iron, cobalt, and nickel. In that respect Mn-Mo shows the same anomaly as Mn-Cr and Mn-V systems.' A second feature is that in common with the two other known molybdenum (Fe-Mo and Co-Mo), Mn-Mo v exists only at elevated temperatures. The X-ray powder pattern of the pure a phase of Mn-Mo is given in Table 11. It agrees well with the patterns established for other structures, especially with that for Fe-Mo as given by Goldschmidt.An attempt is being made to establish whether an ordering of the respective atoms occurs and such information will be reported in a future publication. Acknowledgment The authors acknowledge gratefully the assistance of Mrs. J. R. Belanger in some portions of this work. References 'J. S. Kasper, B. F. Decker, and J. R. Belanger: Journal of Applied Physics (1951) 22, p. 361. 2 A. H. Sully: Journal Inst. Metals (1951) 80, p. 173. H. J. Goldschmidt: Research (1949) 2, p. 343.

Jan 1, 1954

The following figures (Nos. 1-4) and tables (Nos. 1 and 2) were inadvertently omitted from the chapter entitled "Optimum Open-Pit Mine Production Scheduling" by Thys B. Johnson, Section 4, pages 539-562. [ ]

Jan 1, 1969

By Dick Whittington, W. R. Taylor

GENERAL In mid-1974, a representative of ARCO Petroleum Company walked into our Austin offices and asked for a permit for ARCO's first Clay West Mine site. This was the first in situ uranium mining permit issued in the United States. That initial permit, issued in January 1975, was for three acres. The four years since have been characterized by growth and change. Today there are 16 permits approved for approximately 1,540 production acres issued to five companies at eight sites in four counties. There are approximately seven additional permit applications being processed or on the verge of being submitted for an estimated 2,000 additional acres of production. As a rough gauge of the financial scope of this activity, at the typical 40 production wells per acre and an estimated $2,000/well, operators hale installed or committed $122 million for production wells. This does not account for the exploration and development wells installed to delineate the ore or the cost of processing facilities for extracting the uranium. HISTORY OF URANIUM MINING IN TEXAS Information I have concerning early in situ uranium mining activities is "sketchy" but the apparent first on-site test of in situ uranium mining was conducted between 1967 and 1971 at the Dueterstat site, north of Yorktown in Gonzales County, by City Service. Others ran tests at the Bruni site in Webb County and the Burns and Clay West sites in Live Oak County in the mid-70's. During this period, Texas Water Quality Board personnel in the central and district offices maintained a general surveillance of these various test activities. Regulation of in situ uranium mining was formalized with the issuance of a permit in January 1975 with the advent of ARCO's initial production scale (3 acre) effort in the Clay West area at the Moser mine site. Since 1975, the accelerating rate of mining and exploration activity is noticeable. There were 16 exploratory rigs operating early in 1977. This year, the rig count is averaging 46--a 287% increase. HISTORY OF LEGISLATION Paralleling this mining activity was state and federal legislation which subjected in situ mining to environmental regulation. The following is a brief chronology of the legislation that is directly or indirectly related to uranium mining. As most of you know, disposal wells are an integral part of most in situ uranium mines operating in Texas. They are used both during production and during aquifer restoration following production. The wells are regulated by the Texas Injection Well Act, enacted in 1961 by the Texas Legislature. In 1967, the Water Quality Act established the Texas Water Quality Board, and provided for the regulation of water quality by the so-called permit system. In 1969, the Solid Waste Act was enacted by the Texas Legislature. The legislation provides for control of wastes from manufacturing, mining, and agriculture. This Act regulated uranium surface mining activities until 1975 when the Texas Surface and Mining Reclamation Act placed responsibility with the Railroad Commission for uranium open-pit mining and surface mining of coal and lignite. In 1972, the Federal Water Pollution Control Act (Public Law 92-500) was passed. This legislation forms the legal base for the NPDES (National Pollutant Discharge Elimination System) and the subsequent point source effluent guidelines and standards. The November 6, 1975 issue of the Federal Register published interim final rules for Best Practical Treatment levels for effluent discharges from ore mining and dressing operations. Litigation was immediately initiated by eleven companies against these proposed rules, and they are currently being reconsidered for reissuance in 1979. In 1974, the Federal Safe Drinking Water Act (Public Law 93-523) was enacted. A part of this legislation is the Underground Injection Congrol Program. The regulations implementing this program have undergone various public hearings and it is expected that they will be published in the Federal Register before the end of 1978. In 1975, the Texas Surface Mining and Reclamation Act (Senate Bill 55), providing for the Railroad Commission's authority to require reclamation of surface mines, was passed. In 1977, an amendment to Senate Bill 55 was introduced that proposed to place regulation of in situ mining of coal, lignite, and

Jan 1, 1979

By O. N. Carlson, D. G. Alexander

THE hardness anisotropy of metals and alloys has been of increasing interest in recent years but silicon ferrite,1 niobium,2 and tungsten3,4 are the only bcc metals about which this type of information has been reported. This investigation was carried out on vanadium and chromium single crystals in an effort to determine to what degree the hardness variations observed in these metals are due to orientation effects and to compare their behavior with other bcc metals. In earlier work the authors had observed a small angular dependence in the Diamond Pyramid Hardness of single crystalline vanadium on the (100) plane but no anisotropic effects were noted on either the (110) or (111) planes. At the suggestion of R. G. wheeler5 it was decided to investigate this effect in greater detail using the more asymmetric Knoop indentor. The vanadium metal used in the study was prepared by the aluminothermic reduction of V2O5 followed by electron beam melting.6 The principal analyzed impurities were 230 ppm C, 230 ppm O, 65 ppm N, 90 pprn Al, Cr not detected, 50 ppm Fe, 60 ppm Ni, and 200 ppm Si. The chromium was an iodide-refined product obtained from the Chromalloy Corporation. Analysis of this material showed the following amounts of impurities present: 10 ppm C, 9 ppm O, 2 ppm N, 0.4 ppm H, 3 ppm Al, 2 ppm Ca, 2 ppm Cu, 20 ppm Fe, 1 ppm Mg, 0.3 ppm Mn, 1 ppm Mo, 3 ppm Ni, 10 ppm Si, and 1 ppm V. Single crystals of both metals about 1 cm in diam and 10 cm in length were grown by an arc-zone melt- ing technique.7 The chromium crystal was annealed at 1600°C for 6 hr in a purified argon atmosphere to remove any strains or inhomogeneities, but the vanadium was tested in the as-grown condition. The crystals were oriented by the Laue back-reflection method and then sectioned with a spark cutter into individual specimens with a (loo), (110), or (111) plane parallel to the crystal surface. They were mounted in Lucite and carefully ground to a flat surface. The vanadium specimens were then electropolished in a 6 pct perchloric acid-methanol mixture while the chromium specimens were mechanically polished on a Syntron vibratory polisher using an alumina abrasive. The orientation of each crystal was then rechecked by the back-reflection X-ray method. All of them were found to lie within 2 deg of the desired orientation with the exception of the (110)-Oriented chromium crystal which was within 4 deg. Microhardness impressions were taken at 10 deg intervals from the common (110) direction by rotating the crystal in the plane of the crystal surface. A Knoop indentor was used with a 400-g load on the vanadium crystals and an 800-g load on the chromium. The hardness values are averages of 6 impressions and standard deviations were calculated for each set of data. The values reported for the (111) plane of vanadium are based on from 10 to 15 measurements for each point. The microhardness results for vanadium and chromium are plotted as a function of the angular rotation of the long axis of a Knoop indentor from the (110)

Jan 1, 1970