Search Documents

By Y. C. Liu

An analysis is presented to show that the formation of rolling textures in fcc metals can be rationalized in terms of flow mechanisms operative during the rolling process. First, a general approach used by Calnan is followed, where the rolling process is approximated on the basis of two axes, p and Q. In this treatement there are two separate sets of slip systems, one for each axis, and it is shown that a homogeneous rotation can he achieved by restricting the slip systems for the two axes to share common slip directions Then, two criteria are used to select the active slip systems for the axis P: they must have relatively high resoloed shear stresses, and dislocations on these slip systems must interact attractively in order to lower total energy content Finally, a method of analysis is introduced to locate the end position of an axis by knowing its acti7.e slip systems. The result of the analysis indi- cates that two main flow mechanisms operate in fcc metals. The ideal orientation derived from one oj-them is (8 13 21) (21 8 13) which is very close to the (358) (523) orientation observed experimentally on the rolling texture of copper. This flow mechanism should only he operative in metals containing dislocations extended into partials separated by less than five times their lattice parameter. The ideal orientations derived from the other flow mechanism are a combination of (1 10} (112) and a spread of orientations with (110) parallel to the rolling plane. This type of ideal orientations corresponds to those observed in the rolling texture of silver 30:70 brass, and binary alloys with high alloying content. This flow mechanism should be operative in any fcc metal regardless of its stacking-fauIt energy. When a polycrystalline metal is subjected to a large amount of plastic deformation, it is generally observed that grain orientations alter and align themselves towards certain positions, eventually reach-

Jan 1, 1964

By T. S. Mohibatsela, R. V. Ramani, C. V. Manula

The Mineral Engineering Department of The Pennsylvania State University has developed a suite of computer models for anthracite open pit mining (Fig. 1)1 Individual sub-systems have been developed to (a) interpolate geologic field data to obtain coal tonnages, waste volumes, and strip ratios; (b) simulate equipment performance on selected pit profiles to generate data required to choose coal and waste removal equipment; and (c) evaluate selected cost factors to determine either a rate of return for a specified selling price or vice-versa. This paper describes the application of two of these subsystems, namely, the Reserves Model (GEOL) and the Open Pit Materials Handling Simulator (OPMHS), and how these may be applied for the selection of equipment for a prime anthracite mining site.2

Jan 1, 1981

By Charles S. Barrett

This paper is a progress report covering metallographic applications of the electron microscope that have been made during the past year at Carnegie Institute of Technology. An account is presented of the techniques that have been most satisfactory, the difficulties encountered, the resolution obtained, and the peculiarities that have been noted in the microstruc-tures. About 1200 exposures have been made during the year on the instrument, which is an RCA type B2 transmission microscope,' and a number of these have been selected to illustrate the results obtained. prints are also included showing the common types of falsities—to borrow a term from the biological field, the "artifacts." ln brief, the paper is a record of our attempt to determine the value of the electron microscope in the study of the structure of metals and alloys. In addition to comments on techniques and the quality of photomicrographs obtainable with them, the paper discusses the nature of the etch attack on a few metals, and the possible relation between the fine structure revealed by etching and the mosaic block structure of the grains, since numerous papers and reviews are available on the subject of imperfection in crystals, the comments here may be very brief; in fact, are restricted almost entirely to points having to do with recent theories relating the strength of metals to imperfections and to spacings of slip lines. Specimen Preparation and Photographs Mechanical polishing by hand was used throughout this work. Precautions that must be taken in microscopy at high magnification, which have been well explained by Vilella in his book on Metallographic Technique for Steel, are likewise important with the electron microscope. This applies particularly to the need for these polishing and etching (each successive polish becoming less severe and each etch lighter), since the fina1 etch should in general be no heavier than is used for oil-immersion optical microscopy and in many instances should be much lighter (compare Figs. 6a and 7a, 6d and 7b). An extremely light etch, of course, is incapable of cutting through a flowed layer of appreciable thickness. Unquestionably it would be very advantageous in each instance to compare the structures obtained by electrolytic polishing with those obtained by mechanical polishing, but difficulties with the electrolytic method have prevented this in the following collection of prints. The choice of etchant is important, of course; for example, picral proved superior to nital for tempered martensite. With the exception of Figs. Ib and 16, the replicas used were of silica, deposited upon polystyrene and floated from the polystyrene in ethyl bromide according to the method of Heidenreich and Peck.2 The samples were mounted in Bakelite, polished and etched, then the polished Bakelite

Jan 1, 1944

By Charles S. Barrett

This paper is a progress report covering metallographic applications of the electron microscope that have been made during the past year at Carnegie Institute of Technology. An account is presented of the techniques that have been most satisfactory, the difficulties encountered, the resolution obtained, and the peculiarities that have been noted in the microstruc-tures. About 1200 exposures have been made during the year on the instrument, which is an RCA type B2 transmission microscope,' and a number of these have been selected to illustrate the results obtained. prints are also included showing the common types of falsities—to borrow a term from the biological field, the "artifacts." ln brief, the paper is a record of our attempt to determine the value of the electron microscope in the study of the structure of metals and alloys. In addition to comments on techniques and the quality of photomicrographs obtainable with them, the paper discusses the nature of the etch attack on a few metals, and the possible relation between the fine structure revealed by etching and the mosaic block structure of the grains, since numerous papers and reviews are available on the subject of imperfection in crystals, the comments here may be very brief; in fact, are restricted almost entirely to points having to do with recent theories relating the strength of metals to imperfections and to spacings of slip lines. Specimen Preparation and Photographs Mechanical polishing by hand was used throughout this work. Precautions that must be taken in microscopy at high magnification, which have been well explained by Vilella in his book on Metallographic Technique for Steel, are likewise important with the electron microscope. This applies particularly to the need for these polishing and etching (each successive polish becoming less severe and each etch lighter), since the fina1 etch should in general be no heavier than is used for oil-immersion optical microscopy and in many instances should be much lighter (compare Figs. 6a and 7a, 6d and 7b). An extremely light etch, of course, is incapable of cutting through a flowed layer of appreciable thickness. Unquestionably it would be very advantageous in each instance to compare the structures obtained by electrolytic polishing with those obtained by mechanical polishing, but difficulties with the electrolytic method have prevented this in the following collection of prints. The choice of etchant is important, of course; for example, picral proved superior to nital for tempered martensite. With the exception of Figs. Ib and 16, the replicas used were of silica, deposited upon polystyrene and floated from the polystyrene in ethyl bromide according to the method of Heidenreich and Peck.2 The samples were mounted in Bakelite, polished and etched, then the polished Bakelite

Jan 1, 1944

By St. John, JOHN Ancel

AT THE New York meeting of the Institute of Metals Division in February, 1927, Jeffries and Tarasov presented a paper on Tungsten and Thoria,1 in which the experimental facts were interpreted in accordance with the prevailing point of view that the thorium is present as the oxide, thoria. In discussing that paper the writer of this article stated that his own investigations, which had been unavailable to Messrs. Jeffries and Tarasov, showed that the so-called "thoriated" tungsten filament failed to disclose any sign of the oxide when subjected to X-ray diffraction analysis, but did give plenty of evidence of the presence of metallic thorium and, in certain cases, of a material believed to bean alloy of tungsten in thorium. Since these results were completely at variance with the results reported in the paper under discussion and with other papers which had preceded it from time to time in the past, it was felt that further discussion should be withheld until the new evidence could be presented adequately. Arrangements were therefore made to present that evidence at this meeting. MATERIAL EXAMINED The material examined was high-emission filament such as is used in radio tubes, supposed to contain about 0.75 per cent. thoria. The actual analysis was not stated.

Jan 1, 1927

By Ford R. Bryan, Edward F. Runge

BECAUSE of the need for ductile heat resistant alloys of non-strategic composition, there has been metallurgical development of Fe-A1 alloys possessing improved ductility and hot strength, together with high oxidation resistance. Iron and alu- minum form solid solutions up to approximately 35 pct Al. Alloys in the 8 to 12 pct A1 range are characterized by excellent oxidation resistance, high electrical resistivity' and, when appropriately alloyed, have creep rupture strength equivalent to that of the austenitic stainless steels.' At higher aluminum levels, the magnetic properties are of considerable interest. Nachman and Buehler" have recently reported on the desirable magnetic characteristics of the 16 pct alloy.

Jan 1, 1957

By Thomas Harris

This paper. was written in conjunction with the work being undertaken by the Technical Committees on Classification of Coal, and an effort has been made to compile information relative to the use of coal for stationary steam generation in order to use this information to assist the Committee on Classification of Coal for the ultimate purpose of elimination of losses both by the' reduction of indivi-dual effort and waste in the consumption of material. Under the auspices of the National Association of Purchasing Agents, a questionnaire was drawn up to develop this information from stationary steam plants throughout the United States. in order to consolidate the information de-veloped from the many hundreds of boiler tests on coals consumed by various coal¬burning equipment. These questionnaires covered: 1. The company reporting, location and method of delivery to the plant. 2. Complete coal date, including description of coals used (with. sufficient space to- include first, second and third, preference) on--source of coal used,- complete-analysis and factors affecting choice of, coal used. 3. Plant data, divided into - A. Hand fired, B. Overfeed stokers,. . C. Underfeed stokers, D. Traveling grate stokers, E. Pulverized coal, and included complete description of furnace data, draft data, coal-burning rate, type of stoker, type of pulverizer, efficiency date and remarks.

Jan 1, 1933

By G. H. Gronhovd, W. H. Oppelt

Complete gasification to produce synthesis gas for manufacture of synthetic chemicals and fuels offers possibilities for utilization of the vast lignite fuel deposits in the U.S. The design of a slugging, fixed-bed, pressure gasification pilot Plant is described. Results are presented for initial operation of the plant at moderate pressure and using low-temperature char as fuel. Gasification of solid fuels is becoming increasingly important in the future overall energy picture, both in this country and abroad. Snythesis gas from gasification of coal consists chiefly of carbon monoxide and hydrogen, and after suitable purification and modification this gas can be used in the production of synthetic ammonia, methanol, higher alcohols, and synthetic liquid fuels, or as a reducing gas in the metallurgical field.' Most synthesis gas used in this country is made from natural gas, petroleum oils, and refining tail-gases, but the direct gasification of coal will become more attractive as costs of petroleum oils and natural gas increase.' A gasification process designed for use with brown coal and lignite was developed by the German Lurgi Co. prior to World War 11. In this process a fixed bed of lump-sized fuel is gasified with steam and oxygen at pressures ranging from 370 to 440 psi. Effective heat exchange between the ascending high-temperature gases and the descending solid fuel results in low gas outlet temperatures, high thermal efficiency, and favorable oxygen consumption. Lurgi gasifiers are used commercially for the production of synthesis gas or as a substitute for coal gas in many countries, including Germany, Czechslovakia, Great Britain, South Africa, Australia and Pakistan.3-6 The chief disadvantage of the conventional Lurgi gasifier which operates under nonclinkering conditions is that large quantities of excess steam must be supplied with the oxygen-steam mixture to reduce the temperature in the fuel bed below fusion temperature of the ash. Most of the steam leaves the gasifier undecomposed with the product gas and, after cooling, produces large amounts of dilute liquor. Evaluation of fixed-bed gasification experiments using dry-ash removal indicated that by increasing the oxygen concentration in the oxygen-steam blast the temperature in the combustion zone could be raised high enough to operate under slagging conditions. 7-8 Operation of a fixed-bed pressure gasifier under slagging conditions would reduce the steam requirements and the volume of waste liquor and would increase the steam decomposition, the overall thermal efficiency of the process, and the rate of gas production per unit cross sectional area of the gasifier. Because the Lurgi gasification process, modified for slagging operation, offered possibilities for efficient gasification of American lignite, the Bureau of Mines decided to investigate the process on a pilot-plant scale at the Grand Forks, N. D., Lignite Research Laboratory. DESIGN Description of Pilot Plant: A flowsheet of the Grand Forks slagging gasification pilot plant is presented in Fig. 1. The gasifier unit consits of the coal lock, the gas generator, and the slag lock. The fuel, which is periodically charged to the coal lock, moves by gravity flow into the generator and is continuously gasified by an oxygen-steam mixture introduced at the bottom of the gasifier. Molten slag is formed at the hearth and flows through a central taphole into a water quench bath. The slag-water slurry is periodically discharged from the slag lock. Process steam is generated and superheated in separately-fired, oil-burning units. Oxygen is supplied to the gasifier from a gas storage bank located some distance from the pilot plant. The capacity of the oxygen storage bank is about 130,000 standard cu ft at 2200 psig. Liquid oxygen is delivered by truck and is converted to gas during the filling operation. The superheated steam and oxygen are metered separately, then mixed and fed to the gasifier tuyeres. The gas generator is surrounded by a water jacket. The steam formed is separated in the steam drum and then discharged to the gas offtake, thus equaliz-

Jan 1, 1961

By Ashok K. Sinha

The quasi-binary systems "VFe3"—VCo,—VNi,— "VCu3"and "TiFe3"—TiCo3,—TiNi3-"TiCu3"have been studied by a combination of microscopic and X-ray methods. Of the Phases encountered, eleven had close-packed ordered layer structures. Within each system, there is an approximately linear variation of the degree of hexagonality of the stacking arrangement with electron concentration, e/a. A study of eighty -four known examples of AB3 structures in transition metal alloys indicates that at e/a = 8.65 the ordered structure of the close -packed layers changes from "triangular" (AuCu3 type) to "rectangular" (SbCu3 type). At e/a < 8.65, the slope of hexagonality us e/a line increases with the group number of the A component. An interesting series of close-packed ordered structures is known to exist at the composition AB3; however, their alloy chemistry has not yet been fully understood. Dwight and Beck1 observed a correlation between position of the components in the periodic table and the type of crystal structure of the binary AB2 structures formed by transition metals. No consistent effect due to atomic size was noted and they proposed that electron concentration* predominates in In the present paper, the AB3 structures are characterized by a symbol describing the stacking and a symbol specifying the ordered layer. The stacking symbol used was introduced by Zhdanov,7 and later used in the International Tables,8 and by Beck9 in his survey of possible layer stacking structures. Alternating positive and negative integers are used to represent the number of positive (e.g., in abcabc...) and negative (e.g., in cbacba...) stacking sequences. T denotes the triangular ordering found in close-packed planes of the AuCu3 structure and R the rectangular ordering found in close-packed planes of the SbCu3 structure, Figs. 3(a) and (b). The present structure symbols are listed in Table I alongside the prototypes, where known, and other structural characteristics of AB3 phases found in the present investigation. EXPERIMENTAL The starting materials were metals of 99.9+ purity. The alloys were prepared by arc melting under argon atmosphere using a nonconsumable tungsten electrode and water-cooled copper hearth. The total weight loss upon melting and subsequent annealing was always less than 0.5 pct and hence the alloys will be referred to by their intended (unanalyzed) compositions. The alloys were homogenized and annealed at suitable temperatures in the range 750" to 1200°C, the annealing periods varying from 3 days at 1200°C to 10 days at 750°C. The heat treatments were carried out in sealed silica capsules under argon atmosphere and with a molybdenum foil cover between the alloy and the walls of the capsule. The quenched alloys were microscopically examined and reduced to powder by crushing or filing. The powders were, whenever necessary, given a stress-relieving anneal at the original annealing temperature. X-ray powder patterns were obtained with an asymmetrical focusing camera, a Guinier-deWolff focusing camera, or a Debye-Scherrer camera. Cr, Co, or Cu radiations were used. In some cases, to ensure the minimum degree of contamination, the deeply etched specimens were mounted in the asymmetrical focusing camera to obtain an X-ray pattern. Internal silicon standards were employed for lattice parameter determinations. The intensity calculations were made by using a Fortran IV program

Jan 1, 1970

By E. A. Gulbransen, J. W. Hickman

ONE of the important factors that determine the resistance of a metal or alloy to further chemical reaction is the structure of the superficial oxide film A thorough understanding of the physical and chemical structure as well as the stability of the oxide film formed on the surface as a function of time and temperature of the chemical reaction might furnish clues as to the nature of the reaction process and the protective nature of the film A comprehensive program has been undertaken to study these phenomena This paper summarizes the structure of the oxide films formed on the metals iron, cobalt, nickel, chromium and copper at temperatures up to 700°C Before the introduction of the electron diffraction technique, it «as necessary to use either direct chemical analyses or X-ray diffraction analyses to determine the nature of the oxide film formed on the metal or alloy Chemical analyses yields information on the percentages of the several atomic species present in the film while X-ray diffraction analyses yield information on the atomic geometry In special cases the information obtained may be identical, but in general both view-points are necessary Much of, the early work was carried out on the oxidation of bulk samples where thick films were obtained The products were identified after cooling to room temperature by X-ray diffraction and chemical analyses Although much useful information has been obtained in this manner, little could be learned about the character of the protective oxides during the period when the films were actually protective Evidence concerning the chemical structure of thin oxide films has been made possible by the development of the electron diffraction reflection technique In this method the most fruitful investigations have been made by carrying out the reaction in situ at the temperature at which the film is actually protective LITERATURE The oxidation of iron has been extensively investigated by X-ray and electron diffraction Jackson and Quarrell1 found that oxide films formed and examined at the same temperature differed considerably from those allowed to cool to room temperature The results showed that below 400°C the oxide that was stable in intimate contact with iron was Fe304, between 515° and 900°C the stable film was FeO Above the upper change point of iron the oxide was found to be Fe304 prom 400° to 515°C , FeO, Fe304 or a mixture of the two oxides was found Recrystallization of the air-formed film below 400° and above 900°C led to the formation of Fe304 In the range where thicker films consisted of FeO, the air-formed film was converted to a new hexagonal oxide not previously described

Jan 1, 1946

By Frederick N. Rhines, Robert F. Mehl

IT has been shown elsewhere1 that the data on the rates of diffusion in solid metals are fragmentary and in many cases unacceptable. As a result, relatively little is known concerning the factors determining rates of diffusion and the variations in these rates with temperature. The first form of Fick&apos;s law (equation 1 below), ‡ in which the diffusion coefficient D is assumed invariant with composition, has been recognized for many years as only an approximation. The differential equation representing the second form of Fick&apos;s law (equation 4 below) has only recently been integrated by Matano,2 and unfortunately only in cases where a full diffusion-penetration curve (concentration-distance curve) has been obtained can the Matano solution be applied. The proper analysis of diffusion data is thus confined to the data of Grube and Zedele and of Zedele.§ These data are essentially for one temperature alone and do not furnish any information on the variation of the activation heat of diffusion, Q, with concentration: no information exists on the variation of Q with concentration within a singles olid solution field. 11 Much of the argument concerning the properties of metals that determine D and Q has been drawn from data in which variations of the quantities with concentration are unknown, for these data have been taken from experiments that could not furnish this information. Speculation concerning the properties of metals that may be effective in determining D and Q on the basis of data in which the chosen D and Q values are averages over wide concentration ranges of values at particular concentrations, ranges often of 100 per cent, is likely not to be fruitful.

Jan 1, 1938

By F. Weinberg

Lead single crystals have been deformed in tension over the temperature range of 4.2°K to the melting point. Changes in flow stress resulting from temperature cycling and strain rate cycling have been measured as a function of temperature for crystals of different orientations and purity. It was found that the flow stress ratio, after correcting for the temperature dependence of the shear modulus, decreased progressively with temperature above approximately 0.5Tm. The activation energy calculated from the high-temperature portion of the curve was found to be markedly higher than that of self-diffusion. For single glide crystals, the corrected flow stress showed an increase above 0.5 Tm before decreasitzg with temperature. This increase is attributed to static recovery occurrittg during temperature cycling. THE temperature dependence of the flow stress, based on temperature cycling and strain rate cycling, has been extensively investigated,&apos; and on the basis of these results dislocation models of the work-hardening process have been proposed. In general, the flow stress is divided into two parts, ts, the short-range interaction term, which is only effective at low temperatures and which decreases with increasing temperature, and TG, the long-range stress term, which is independent of temperature after allowing for the temperature dependence of the shear modulus. The observations demonstrating that tG/µ is independent of temperature were generally carried out at low temperatures to minimize recovery effects. Several investigations have been reported on flow stress measurements at high temperatures2"5 which demonstrate that TG/µ does not remain constant at temperatures above 0.5Tm (where Tm is the melting temperature of the material in OK). Specifically, Hirsch and warrington3 carried out temperature cycling tests at two strain rates on single and polycrystalline aluminum up to 0.8 Tm and on polycrystalline copper. For aluminum they found that the flow stress ratio (the flow stress at temperature T2, divided by the flow stress at the reference temperature T1 in one temperature cycle) dropped progressively with increasing temperature above 0.5Tm. From the slopes of the high-temperature portions of the curves, they determined an activation energy for the deformation process of 1.6 ev (at best) which they considered was in agreement with the activation energy of self-diffusion, 1.35 ev. Calculations of the activation volume demonstrated that the deformation was not controlled by dislocation climb. They proposed a mechanism in which the rate-controlling process at high temperatures was due to the rate of move- ment of vacancies away from jogs, i.e., that of self-diffusion. Results of Lucke and Buhler4 on single crystals of aluminum confirmed this conclusion. They measured the critical resolved shear stress of aluminum over a wide range of temperature and strain rates. They found that the temperature dependence of the critical resolved shear stress was similar to that of the flow stress ratio, as determined by Hirsch and Warrington, and from their data calculated an activation energy for high-temperature deformation of 1.35 ev identical to that of self-diffusion. More recently Gallagher5 has carried out a detailed investigation of the temperature dependence of the flow stress ratio of copper, silver, and gold. In all cases, he found that the flow stress ratio, after adjusting for the shear modulus temperature change, drops at high temperatures. The activation energies he determined were found to be appreciably higher than the activation energy of self-diffusion of the material being considered. The flow stress ratio was found to be dependent on the orientation of the material, and, in addition, an anomalous increase in the flow stress ratio for copper, oriented for single glide, was observed above 0.5Tm. The purpose of the present investigation was to measure the critical resolved shear stress, the flow stress ratio, and the strain rate sensitivity of lead, primarily as a function of temperature. The results should indicate whether, following Lucke and Buhler, the critical resolved shear stress of lead has the same temperature dependence as the flow stress, and, following Hirsch and Warrington, whether the activation energy for high-temperature deformation in lead is the same as that of self-diffusion. Lead deforms as a normal fee material,6&apos;7 is available in high-purity form, can readily be grown as single crystals, and, for this investigation, has the very considerable advantage of having a low melting point, 327°C. The observations of the critical resolved shear stress of lead have been published elsewhere.&apos; EXPERIMENTAL PROCEDURE The experimental procedure was essentially the same as that used in the critical resolved shear stress measurements.&apos; Single crystals of 99.999 pct (59) and 99.9999 pct (69) lead were deformed in tension with a table-model Instron in a silicone oil bath above room temperatures and in a cooled methyl alcohol or liquid-nitrogen bath below room temperatures. The test specimens were rectangular in section, 0.65 by 0.33 cm, and had a 5-cm gage length. The specimens were grown as single crystals with tapered ends, which fitted into matched tapered grips for testing. To obtain the flow stress between two temperatures, specimens were first deformed approximately 1.0 pct at the higher temperature. The test was then stopped, the load relaxed, the oil bath removed without disturbing the specimen, the grips and specimen cooled with a fan and then immersed in liquid nitro-

Jan 1, 1969

By G. W. Brock

Experiments in the form of aging of overstrained tension specimens and elevated temperature tension testing, have been carried out on recrystallized arc-cast molybdenum. The aging behavior of molybdenum was found to be strongly dependent on the degree of plastic strain present in the lattice: the reason for this being the low solid solubility for the common interstitial elements in molybdenum. GEORGE W. BROCK, formerly Research Associate, Department of Theoretical and Applied Mechanics, University of Illinois, Urbana, III., is Research Associate, Department of Engineering Sciences, IBM Research Center, Yorktown Heights, N. Y. Manuscript submitted January 19, 1961. IMD THE term strain aging is familiar in connection with the recovery of the yield point in mild steel after tensile overstraining, and there are other instances where it is known to exert an appreciable effect on mechanical properties. For example, steel exhibits a greater tensile strength at mildly elevated temperatures than at room temperature and serrated stress-strain flow curves occur under certain conditions. It has been known for a number of years that the phenomenon of strain aging is directly connected with the presence of carbon and nitrogen in the lattice; and extremely small amounts of either element are sufficient to produce the effect. In this study, the aging behavior of overstrained tensile specimens of recrystallized molybdenum has

Jan 1, 1962

By Albert Sauveur

This paper explains the possibility of using advantageously a boiling solution of sodium picrate to reveal dendritic segregation in steel. The mechanism of the action of the reagent is described. The failure of manganese alone to produce persistent dendritic segregation is also considered. IRON, like other metals, solidifies through the formation of dendritic crystals; iron alloys forming solid solutions, like other solid solutions, solidify likewise through the formation of dendritic crystals. The alloying elements or impurities as well as the inclusions segregate generally in the interstices, or "fillings," between the axes and branches of the dendrites; that is, in the portions last to solidify. This results in dendritic segregation or heterogeneity, which is generally persistent and makes possible the revelation of the dendritic crystallization of the metal through the selective action of a suitable etching reagent.1 For this purpose, a cupric solution, such as Le Chatelier&apos;s, is generally used, copper being deposited on the pure, or relatively pure, ferrite present in the axes while the fillings remain free, or relatively free., from copper deposition. The dendritic structure, formed on solidification in a steel containing 0.50 per cent. carbon, 0.37 per cent. manganese, 0.12 per cent. silicon, 0.07 per cent. sulfur, and 0.035 per cent. phosphorus is shown, after treatment with Le Chatelier reagent, in Fig. 1 under a magnification of 8 diameters. Commercial steel always contains inclusions of manganese sulfide, which are located in the fillings of the dendrites. Comstock has shown that boiling sodium picrate imparts a dark coloration to these inclusions. We find that this reagent likewise reveals dendritic segregations in commercial steel, as shown in Fig. 2, under a magnification of 8 diameters, which represents the same spot as that shown in Fig. 1. The fillings

Jan 2, 1924

By Donald W. Scott

This paper describes the application of ore-dressing methods to the reclamation of milled frit from over-spray, or waste, porcelain enamel. Frit is the name given by enamelers to a granulated glass produced by the smelting and subsequent water quenching of various ingredients capable of forming a glass, usually including a compound to produce opacity. It is the major component of porcelain enamel, and normally commands a price ranging from 7 to 12 cents a pound. In the *preparation of a white enamel slip, usually 6 or 7 parts of clay, 2 parts of opacifier, small amounts of electrolytes, in some cases inorganic color stabilizeis and organic dyes, and 35 parts of water are added to 100 parts of frit; the mixture then is milled to a fineness of the order of 92 to 95 pct through a 200-mesh sieve. The frit forms the base of the enamel; the opacifier imparts opacity or reflectance; the clay suspends the frit while in slip form and serves as a binder in bisque form (dry and unfired); and the electrolytes control the workability. Spraying is used commercially, in many cases, to apply the finish coat of enamel to the ware, prior to drying and firing. In the spraying operation, only about 50 pct, by dry weight, of the enamel slip adheres to the surface of the ware, the remainder forms the over-spray. From 1/2 to 2/3 of the overspray goes up the flue where it is lost or recovered, depending on whether the plant is equipped with a dust-collecting installation; the coarser portion of the over-spray is collected in the spray booth. The former product is termed flue reclaim enamel, and the latter booth reclaim enamel. Although the spraying operation is done in specially constructed booths, which are partially or completely enclosed, it is extremely difficult to keep out contaminating dirt, which joins the reclaim. Some present-day large enameling plants use 20 tons of frit a day, of which 10 tons go into reclaim with a potential value of $1400 to $2400. When two-coat finish enamels were common, the reclaim was used satisfactorily for the undercoat, but the relatively recent advent of one-coat finish enamels prevented use of the reclaim because, even when blended with first-run enamels, it gave dirty finishes with poor gloss. It was thought that the pitting and specking encountered with reclaimed enamels were caused by the contaminating dirt, and that the poor gloss was caused, primarily, by the high clay content; more clay usually was added to give proper suspension properties to the slip when the reclaim was used. A clay content in excess of about 10 pct usually imparted refractoriness to porcelain enamels. Present-day one-coat porcelain enamels must combine high gloss and opacity with freedom from surface defects. Methods of beneficiating the over-spray,

Jan 1, 1948

By Donald W. Scott

This paper describes the application of ore-dressing methods to the reclamation of milled frit from over-spray, or waste, porcelain enamel. Frit is the name given by enamelers to a granulated glass produced by the smelting and subsequent water quenching of various ingredients capable of forming a glass, usually including a compound to produce opacity. It is the major component of porcelain enamel, and normally commands a price ranging from 7 to 12 cents a pound. In the *preparation of a white enamel slip, usually 6 or 7 parts of clay, 2 parts of opacifier, small amounts of electrolytes, in some cases inorganic color stabilizeis and organic dyes, and 35 parts of water are added to 100 parts of frit; the mixture then is milled to a fineness of the order of 92 to 95 pct through a 200-mesh sieve. The frit forms the base of the enamel; the opacifier imparts opacity or reflectance; the clay suspends the frit while in slip form and serves as a binder in bisque form (dry and unfired); and the electrolytes control the workability. Spraying is used commercially, in many cases, to apply the finish coat of enamel to the ware, prior to drying and firing. In the spraying operation, only about 50 pct, by dry weight, of the enamel slip adheres to the surface of the ware, the remainder forms the over-spray. From 1/2 to 2/3 of the overspray goes up the flue where it is lost or recovered, depending on whether the plant is equipped with a dust-collecting installation; the coarser portion of the over-spray is collected in the spray booth. The former product is termed flue reclaim enamel, and the latter booth reclaim enamel. Although the spraying operation is done in specially constructed booths, which are partially or completely enclosed, it is extremely difficult to keep out contaminating dirt, which joins the reclaim. Some present-day large enameling plants use 20 tons of frit a day, of which 10 tons go into reclaim with a potential value of $1400 to $2400. When two-coat finish enamels were common, the reclaim was used satisfactorily for the undercoat, but the relatively recent advent of one-coat finish enamels prevented use of the reclaim because, even when blended with first-run enamels, it gave dirty finishes with poor gloss. It was thought that the pitting and specking encountered with reclaimed enamels were caused by the contaminating dirt, and that the poor gloss was caused, primarily, by the high clay content; more clay usually was added to give proper suspension properties to the slip when the reclaim was used. A clay content in excess of about 10 pct usually imparted refractoriness to porcelain enamels. Present-day one-coat porcelain enamels must combine high gloss and opacity with freedom from surface defects. Methods of beneficiating the over-spray,

Jan 1, 1948

By Norman B. Pilling, George P. Halliwell

The effects of lead and tin up to maximum contents of about 0.1 per cent. each, in the presence of oxygen between 0.04 and 0.30 per cent., have been studied. Tin is retained efficiently in the oxidized condition, whereas lead is not. An approximate relation between the lead-oxygen and tin-oxygen contents is deduced which, if observed, permits the presence of these elements without detrimental effect. Excess of lead beyond this limit affects ductility and rolling properties adversely and an excess of tin correspondingly diminishes the conductivity. It is shown that copper carrying a combined lead and tin content of several hundredths per cent., yet fully equal in quality to electrolytic wirebar, may be produced under commercial conditions. Tin is not normally found in more than bare traces in current grades of American electrolytic copper, and lead is rarely found to more than a few thousandths per cent. In the electrolytic refining of copper these metals do not present great difficulty in separation and their presence in any considerable amount in copper that has been refined by this method need not be tolerated. On the other hand, the effect of these elements is not entirely academic, as a considerable tonnage of scrap copper liberally contaminated with them has been reclaimed by the fire-refining process into metal with a residual lead and tin content of several hundredths per cent., yet having excellent working properties and fully equal in quality to current grades of electrolytic wirebar. Such copper has been found entirely suitable for use in the manufacture of electrical apparatus. In the absence of oxygen, tin is known to depress the conductivity rapidly, and lead to impair ductility and the rolling properties, yet the effects of these metals on commercial grades of copper—i. e., copper containing from 0.03 to 0.10 per cent. of oxygen—apparently has not received systematic attention. Occasional reference is made to the fact that in the presence of oxygen lead may be tolerated, yet Addicks says,1 in regard to overpoling: "The unstable condition can be controlled by adding certain substances, notably lead, in small quantities, but as mere

Jan 1, 1926

By R. F. Lynch, J. D. Wood

The Al-1.0 pct Mg alloy 565 7 was studied using optical microscopy and electron microprobe X-ray analysis. Constituent particles were found to exist inter-dendritically in the as-cast material in a region of precipitate free a -aluminum. Five phases besides a fine precipitate and a-Al were identified in the cast structure: Fel3, Fe2Al7, Mg2Al3, CUMgAl2, and Cu2FeAl7. Thermal treatments conducted for 100 hr at 1180°, 1130°, 1080°, 1030°, 980°, and 880° F revealed a general dissolution and spheroidization of the in-terdendritic constituent network observed in the cast structure. The principal constituents present in the thermally treated structures were FeAl3 and Fe2Al7 with the relative amount of Fe2A17 to FeAl3 increasing with a decrease in the treatment temperature. The phases Present in the wrought structure were identical to those observed after the thermal treatments, with the constituent particles strung out in the direction of rolling. ALLOY 5657 is a nonheat-treatable commercial purity Al-1.0 pct Mg alloy utilized extensively because of its bright finishing characteristics. This investigation was conducted to determine the constituents present in 5657 alloy, and to study the effect of extended thermal treatments on morphology. Numerous studies have been carried out to establish the equilibrium diagrams for various aluminum systems,1-3 with phase identification based on X-ray analysis, morphology, and the etching response of relatively large particles. Phragmen4 conducted a study of the phases in aluminum eutectic systems and compiled a "corrected" table of etching responses, drawing on his work plus that of Schrader,5 Keller and Wilcox,6 and Mondolfo.7 A review of the original work of Keller and Wilcox, and Mondolfo, which was concerned with the constituents found in commercial alloys, reveals that in numerous cases their etching responses differ from those reported by Phragmen and from each other. These inconsistencies may occur because a specific constituent will react to a given etch in a varying manner depending upon its size, the elements dissolved in the phase, the other constituents surrounding a phase, and the solute content of the matrix. Work with a commercial orientation was conducted on alloys 2024 and 3003 by Sperry8,9 and on alloy 3003 by Barker,10 where the relationship between the phase diagram and the nonequilibrium structure of an alloy was examined. Backerud11 investigated the A1-Fe binary system and found that at high cooling rates the equilibrium eutectic reaction forming a-A1 and FeA13 is replaced by another lower temperature eutectic reaction forming a-A1 and metastable FeAl6, a constituent first identified by Hollingsworth et al.12 Most of the above mentioned studies were conducted on materials having a significantly greater alloy content than 5657 alloy, where the relatively small size and sparse distribution of second phase particles hinders the process of identifying constituents. EXPERIMENTAL PROCEDURE Material with a composition as given in Table I was examined in the as-direct chill cast, hot rolled and cold rolled conditions, and after thermal treatment of the cast structure. Thermal treatments were terminated by a water quench. Microscopic examination was conducted under various lighting conditions following the application of standard etchants as specified in Table 11. A semi-quantitative electron microprobe X-ray analysis was conducted for Al, Mg, Fe, Cu, Si, Zn, and Ti. RESULTS AND DISCUSSION Microstructure of the As-Cast Material. Particles of second phase material were found to exist inter-dendritically, principally in regions of precipitate free a-Al, as illustrated in Fig. 1. Adjacent to the ingot edge was a region of inverse segregation, resulting in an increased amount of second phase material containing large sized particles which aided in phase identification. Phase Identification. Cast Structure. Five phases besides a-Al and a fine precipitate were identified using optical microscopy and electron microprobe X-ray analysis, as presented in Tables II and III, respectively. FeA13 and Fe2A17 are often found with Fe2A17 forming a sheath around the core of FeAl3, resulting from an incomplete peritectoid reaction. These phases have a nearly identical appearance under white light, although they are easily differentiated under crossed polarizers, as characteristically illustrated in Figs. 2(a) and 2(b), respectively. Microprobe analysis con-

Jan 1, 1970

By W. L. Saunders

It is now generally admitted by experts that at least so far as rapid progress is concerned the Alpine system of tunnel-driving is superior to any other. This is perhaps natural in view of the record of experience in driving tunnels through the Alps. These great mountain-chains cannot be treated in the ordinary way by shaft-sinking and driving headings, thus multiplying the points of attack. The work must be done from the ends only, hence speed in driving is of the utmost importance ; and, as necessity is the mother of invention, the concentration of effort to make progress has resulted in an organization and in mechanical appliances that have produced results so much in excess of the usual practice, even in America, that a discussion of the subject in detail should be of much value to the engineer and contractor. The first Alpine tunnel mas the Mont Cenis, length 7.5 miles, driven with a progress that averaged about 7.75 ft. per day. Next came the Saint Gothard, 9.5 niiles long, 18 ft. per day; Arlberg, 6.5 miles long, 27.25 ft. per day; Simplon, 12.25 miles long, 36 ft. per day. The figures represent progress when driving from two headings, so that by dividing them in two we get the daily single-heading progress. The latest of the Alpine tunnels is the Loetschberg, now being driven. In this work the world&apos;s record has been beaten by a single day&apos;s record in one heading of 36 ft. and by an average daily record in one heading of 29.5 feet. The Alpine range forms a natural barrier between a large section of northern and southern Europe. This range extends from the southeast of Prance to the frontier of Hungary, betveen Italy and the plains of sonthern Germany. The contour

Jan 1, 1912

By Keijiro Nishio

At a time of great antiquity when our Yomato tribe had not yet found its way throughout the country, there lived in Japan barbarous tribes of the stone age, whose dwellings were vertical caves covered with roof&apos;s of twigs and weeds. In a cave lately discovered at the village of Morita, 10 miles west from the port of Aomori, there were found pieces of micaceous iron-ore and psilomelane, with oval holes pierced from both sides. Apparently these objects were regarded as ornaments or curios, without being applied to any practical use. Among the traditions given in the Nihonshoki, an ancient history of Japan, there is one relating to the mining industry. According to this tradition, in the mythological age Izanami-no-Mikoto gave birth to Kanayamahiko-no-Mikoto, god of mines, and Amaterasu-Okami (the sun-goddess) was armed with swords. It came to pass at one time that she concealed herself in Ama-no-Iwato ("Heavenly Cave"), and several gods made contrivances to entice her out. Among them, Ishikori-dome, a smith, made a mirror with copper obtained from the Ama-no-Kagoyama, by means of a pair of bellows known as the Ama-no-habuki, which was made of a deer-skin. It is recorded also that Susanb-no-Mikoto, her younger brother, observed the abundance of gold and silver in Korea, where his descendants were to reign, and urged them to provide themselves with boats to convey them across the Sea of Japan. In the course of time he accomplished his object, proceeding to Korea with his son, Isotakeru-no-Mikoto. These accounts

Jan 1, 1913