Search Documents

By F. P. Bobrowski, G. B. Spencer, Alton B. Cook

In estimating production gas/oil ratios and oil recoveries from reservoirs containing highly volatile oils it is highly important to include condensate that may be recovered from the gas produced from the reservoir. The volume of the hydrocarbon liquid condensed from the production of the solution gas that has been liberated. in some reservoirs may equal or even exceed the volume of recoverable stock-tank oil as estimated by present methods. The usual procedure1, 2, 3 in estimating future reservoir performance includes use of relative permeability data of the reservoir rock to gas and oil and includes material-balance calculations utilizing data on the volume of the reservoir fluids, oil and gas production and reservoir pressure decline, and data on the physical properties of the initial reservoir fluids. The inaccuracy in the procedure results from the false assumption that all of the free or liberated gas that enters the well bore of reservoirs containing highly volatile oils remains in the gaseous phase as it is produced. This paper presents a method for estimating future reservoir performance and oil recoveries based on special labora. tory analyses of reservoir-oil samples and recognition of the additional volume of hydrocarbon liquid that will be recovered at various stages of depletion from a solution.gas.drive reservoir. The method also includes calculations of the volume and composition of the hydrocarbon liquids that can be recovered by processing the produced gas in a natural-gasoline plant. The development of the method resulted from a study of laboratory analyses of reservoir samples and of field data obtained from two reservoirs containing oil of the highly velatile type. Relatively high pressures and temperatures prevail in oil reservoirs discovered at the greater depths of present-day drilling. The contained fluids may have high saturation -Dressures and large volumes of gas in solution. The oils and gases under these conditions may be almost identical in compositions and densities.4,5 Also, engineers have noted that, for a number of oil reservoirs and especially the deeper reservoirs, the API gravity of the stock-tank oil increaees as the production gas/oil ratios increase. They attributed this increase in API gravity of the stock-tank oil to the formation of condensate as the liberated gas in the reservoir is being produced. SOURCE OF DATA FOR CALCULATIONS Subsurface oil samples and well-test data were obtained from the E. Constantin-Lambert Well No. 1 in the Elk City Field, Okla., to demonstrate the need for and a method of calculating future reservoir performance when consideration is given to the recoverable hydrocarbon liquid from the production of solution gas that has been or will be liberated in a reservoir. The Lambert well is located in C, SW 1/4, SW 1/4, Set- 18, T-l0-N, R-20-W, Washita County, Okla. At the time of completion it was on the east edge of the development and Was producing from conglomerate through 30 perforations in the 5 1/2-in. casing at a depth of 9,859 to 9,864 ft. The well Was completed on July 9, 1949, and subsurface oil samples were obtained July 29 and August 1, 1949. Production gas/oil ratio data were obtained during the operation in series of two Separators at high and low-pressures of 314 and 44 psia, respectively, and at an average temperature of approximately 60°F. The flowing bottom-hole pressure at the time of sampling was 3,934 psis. The static bottom-hole pressure was not obtained at the time of sampling, as the well could not be shut in long enough for testing because gas produced from the well was used for fuel at an offset drilling well. However, the initial reservoir pressure was calculated to be 4,364 psia from knowledge of pressure gradients in other wells in the field and the depth of the casing perforations in the Lambert NO. 1 well.

Jan 1, 1951

By M. N. Pathasarathi, P. A. Beck, T. J. Koppenaal

EARLIER work1 indicated that in rolled and annealed copper the volume fraction of the cube-texture component may increase on continued isothermal annealing. Merlini found2 that in rolled copper the well-known increase in the amount of cube-oriented material with increasing annealing temperature3 is concurrent with grain growth, which takes place after recrystallization is complete. It was found that both in copper2 and in aluminum4 the texture resulting from primary recrystallization, even if this is followed by some grain growth, may in general comprise, in addition to the cube-texture component, four symmetrical texture components of the general type (123)[412], i.e., components not very far from the ideal orientations of the rolling texture. The volume fraction of the cube-texture component increases on further annealing at the expense of these four components.' The present work was undertaken to study quantitatively the increase in the volume fraction of the cube-texture component in the course of normal grain growth, under varying conditions. Since the grain-gr3wth behavior of A1-Mn alloys has been already investigated in some detaiL5 an A1 + 0.8 pct Mn alloy was chosen for this work, in which the extent of normal grain growth can be effectively controlled by the inhibiting effect of a dispersed second phase. EXPERIMENTAL PROCEDURE High-purity aluminum of the following composition was used: A1 99.997 pct, Cu 0.0004 pct, Fe 0.0005 pct, and Si 0.001 pct. A high-purity A1-Mn master alloy was prepared by dehydrating manganese chloride at 500°C and reacting it with molten high-purity aluminum at 750°C in a graphite crucible.5 The Mn metal reduced from the salt by the molten aluminum goes into solution in the latter. The master alloy? containing 13 pct Mn, was solidified under conditions suitable for minimizing segregation. An ingot of the final alloy, to be used in the experiments, was per pared by melting high-purity aluminum and the necessary amount of master alloy in a graphite crucible, and by pouring the molten alloy into a graphite mold preheated to 700°C through a box containing graphite baffles designed to intercept most of the aluminum oxide films floating in the melt. The melt was then solidified by placing the mold on a water-cooled copper plate and by keeping the top of the mold hot, in order to minimize piping. The 6 1/2 in. long, 11/4-in.diam ingot consisted largely of a single crystal. Chemical analysis showed that there was little segregation from the bottom (0.83 pct Mn) to the top (0.81 pct Mn). Spectrographic analysis of the ingot showed that the impurity content remained essentially the same as that of the aluminum used. The ingot was processed so as to obtain a uniformly small grain size. without banding. The ini-tial steps of rolling in the form of a flat bar and of annealing, down through a thickness of 0.4 in., are shown in Table I. At this point the bar was cut into four sections, each approximately 3 in. long, which were processed separately as shown in Table If. The table also gives the penultimate grain sizes obtained in each section by annealing prior to the final rolling of 90 pct RA. During the final rolling the strips were reversed end to end between passes. Annealing treatments were given in a salt pot furnace, with the temperature controlled to 1°C. All annealing of section "6s" was carried out above the solvus point to avoid the formation of second-phase precipitate. The penultimate annealing was sufficiently short to give a relatively fine grain size in spite of the high temperature. Section "6L" was processed in a similar manner, except that the penultimate annealing was much longer, so as to allow considerable grain growth. Section "4" was given the two final

Jan 1, 1961

By Cyril Wells, Robert F. Mehl

The purpose of this investigation was to prepare high-purity iron-carbon alloys, to determine as precisely as possible the A3(GOS), the Acm(SE), and the A1(PSK) transformation temperatures in the meta-stable iron-iron carbide system (up to 1.4 per cent C), and to study the influence of carefully controlled and constant rates of heating and cooling (1/8 to 2o C. per minute) upon the transformation temperature and upon the resulting microstructure. Apart from the general metallurgical importance attending the completion of such a task, it will be noted that highly precise transformation temperatures are of interest and importance in the thermodynamic study of this system1. Several determinations of the iron-iron carbide diagram have been made2. These suffer generally from the low purity of the alloys used, and from the application of methods of investigation of low sensitivity. Attempts to compare and weight the many data available in an effort to construct as accurate a diagram as possible have, in the main, been unsuccessful. In general, the wide differences in the results of different workers, the lack of complete analytical data, the omission of important details relating to the heat-treatment of the alloys, and the meager description of the methods of investigation applied, render such a process of averaging nearly meaningless. It may be seen from the summaries by Epstein2 and Körber and Oelsenl that variations as great as 30' C. exist in the reported data on the A3 temperatures in iron-carbon alloys. Fortunately, the Aa temperature in pure iron is now known to be 910" C. ± 1° C.3 The best recent work on iron-carbon alloys is that of Esser4 on hypoeutectoid steels and that of Sato5 on both hypoeutectoid and hyper-eutectoid steels. Esser made a dilatometric and magnetic study of iron and iron-carbon alloys containing 0.06 to 0.86 per cent C, for which a high purity is claimed. Presumably the electrolytic iron was reasonably pure, but the alloys contained considerable impurities, on the average totaling 0.35 per

Jan 1, 1937

By G. F. Comstock

In the literature of metallography there is a large amount of material describing the various non-metallic inclusions found in iron and steel, and the appearance of sulfides, silicates, oxides, or alumina in steel under the microscope is fairly well known. The inclusions found in non-ferrous metals are, however, not so well known, at least judging from published writings, and the author has been interested in examining small castings of copper, brass, or bronze with certain inclusions purposely mixed with the metal, to see what was the characteristic appearance of each kind of inclusion, and if they could be readily distinguished from one another. The method employed in most cases consisted in overheating and oxidizing a small charge of copper, then cooling it somewhat, and adding a suitable amount of the element whose oxide it was desired to observe. This element was stirred in well and given time to react with the oxygen in the copper, then the melt was poured in a sand mold in the form of a cylinder about 21/2 in. (63 mm.) in each dimension, with a sprue about 11/2 in. (38 mm.) in diameter and 3 in. (76 mm.) high on top of the cylinder, the sprue forming the only riser. Samples for examination were cut sometimes from the center of the casting, and sometimes from the sprue or riser. A few of these samples were cast in chill molds. The appearance of sulfides was studied in an alloy containing 10 per cent, each of tin and lead, with which a flux of plaster of Paris was used. The appearance of foundry sand was studied in several alloys, one of them having sand stirred into the metal intentionally, and others having cut into the molds badly when poured, so that the castings were spoiled by included sand. As all this work was done on alloys having copper as the chief ingredient, the natural starting point was copper oxide, the appearance of which in a micro-section is well known. Cuprous oxide is soluble in molten copper, but separates out in freezing and forms a eutectic containing 3.5 per cent. Cu20, or 0.39 per cent. oxygen. If there is less

Jan 1, 1919

By W. S. Owen, T. Bell

The variation ox the M, temperature with nitrogen concentration has been determined experinzentally. The free-energy difference between martensite and the parent y Phase at the M, temperature,is computed for Fe-C and Fe-N alloys using recent solubility data fm the Fe-N system and new data for the variatim of the activity of the interstitial solute in the y phase with concentration. The "geometric model" is considered also, and the importance of Zener ordering is noted. It is shown that, although at any chosen concentration the M, temperature and the activity are significantly different in the two alloy systems, the free-energy duference is the same within the limits of experimental error, thus Providing further evidence of the very close similarity between the martensite transformations in Fe-C and Fe-N alloys. TO estimate the free-energy change accompanying the martensite transformation in binary interstitial alloys it is necessary to know the variation of the Ms temperature with interstitial solute concentration and some thermodynamic data. To date, only the Fe-C system has been discussed because this was the only system for which relevant experimental measurements had been made, but even in this case the data available are insufficient to permit the free-energy change to be calculated without the assumption of a thermodynamic model for the y and a solid solutions. The last comprehensive discussion of the topic was by Kaufman, Radcliffe, and Cohen in 1.960.' Since that time Ellis, Davidson, and Bodsworth2 have redeter mined the activity of carbon in y iron as a function of carbon content and Atkinson3 has measured the activity of nitrogen in Fe-N austenite. The M, temperature of Fe-N is reported in the present paper. Thus, it is now possible to assess the free-energy change accompanying the martensite transformation in Fe-N alloys on the same basis as that used to assess the change in Fe-C alloys. This comparison is of interest because it has been shown recently4 that the structure of the martensite formed in Fe-N alloys changes with nitrogen content in a manner exactly parallel to the changes in structure in the Fe-C series and that the strain associated with the distortion of the iron lattice in either the y or the a phase by a nitrogen atom is the same as that produced by a carbon atom. The work to be described tests whether or not this close similarity between the two systems extends to the thermodynamics of the martensitic transformations. THE Ms TEMPERATURES FOR Fe-N MARTENSITE Bose and Hawkes5 found the M, temperature of a eutectoid Fe-N alloy (2.35 wt pct N) to be 35°C. This single determination appears to be the only reported measurement of the M, temperature of an Fe-N alloy. In the present work a series of more than fifteen different specimens containing between 0 and 2.7 wt pct N were prepared by controlled nitriding of pure iron wire 0.010 in. diam. The iron was supplied by B.I.S.R.A. and was designated ACN2. The nitriding procedure, all aspects of which are critical, has been described in detail elsewhere.' Each specimen was quenched from the austenitizing temperature into brine at 20°C without removing the specimen from the ammonia-hydrogen atmosphere in which it was ni-trided. Alloys containing up to 0.7 wt pct N were fully martensitic. More concentrated alloys contained progressively more retained austenite. At 2.34 wt pct N the specimen was completely austenitic after quenching to 20°C. The M, temperature of specimens with M, temperature above 20°C (those containing less than 2.35 wt pct N) was determined by a thermal arrest technique. For the more concentrated alloys (2.35 to 2.70 wt pct N) the variation of electrical resistance with temperature down to -196°C was used. Unlike Fe-C alloys, Fe-N alloys cannot be reaus-tenitized in vacuum or in an inert atmosphere because excessive loss of nitrogen occurs, even in short times, at high temperatures. Consequently, the alloys were reaustenitized in the ammonia-hydrogen mixture corresponding to nitrogen equilibrium at the temperatures used. The specimens were quenched in a blast of cold hydrogen gas and the temperature, measured by a thermocouple welded to the 2.5-in.-long specimen, was recorded on a high-speed recorder. In the first experiments 0.002-in.-diam chromel-alumel wire thermocouples were used but it was found that these gave erroneous readings due to contamination by nitrogen pickup. Pt-Pt 13 pct Rh wires of 0.002 in. diam were found to be satisfactory. Further details of the experiments are available in the original thesis.7 The cooling rate was controlled between 400° and 4000°C per sec by adjusting the hydrogen pressure. At least three cooling curves were obtained for each composition. Each specimen was analyzed for nitrogen after quenching. To aid in the accurate location of the martensite arrest points a series of cooling curves of 0.010-in.-diam platinum wire were recorded and these, which did not contain an arrest, were used as comparison standards. Four specimens, each in the form of a 3-in. loop, were prepared from each of the four alloys containing more than 2.35 wt pct N. One specimen was used for nitrogen analysis, one for X-ray diffraction, and two for resistance measurements below 20°C. The latter specimens were quenched from 20°C into constant-temperature baths at selected lower temperatures.

Jan 1, 1968

By R. W. Shearman, F. Weston Starratt

A new center for mining and metallurgical research is developing at Sterling Forest, N. Y., under the auspices of Union Carbide Corp. Here is to be located the Union Carbide Nuclear and Ore Research Laboratories. In truth, history has repeated itself; the Sterling Forest area in the days of the Revolutionary War, and for many years thereafter, was the mining and metallurgical center of the US. For in these Ramapo hills along the New York-New Jersey border, iron ore was mined, pig lion was cast, and the weapons of war and the plowshares of peace were forged. Before embarking on an historical pilgrimage to yesteryear-a brief description of Sterling Forest. Located in Orange County, N. Y., near Tuxedo, immediately north of the New York-New Jersey State line, and just west of the Erie Railroad and the New York State Thruway, Sterling Forest is approximately 35 mi from New York City. Title was acquired in 1956 from the Harriman family by City Investing Co. Its President, Robert W. Dowling, has established himself as a city planner, having conceived such projects as Pittsburgh's Gateway Center and Philadelphia's Penn Center. A unique, self-contained community -is planned that will contain light industry and centers for research and engineering. Colonies of homes will be interspersed throughout the 20,000 acres of forest land, lakes, and rolling hills. Culture will not be neglected, for Sterling Forest will be the new home for the annual Empire State Music Festival The Sterling Forest Gardens, 125 acres of landscaped woodland and streams, will become the "world's largest permanent floral showplace" The Sterling Forest International Research Building was opened earlier this year, and designed to provide all facilities needed by small growth research companies. The first major company to acquire land to construct research buildings at Sterling Forest is Union Carbide. 1763 ... Discovery of iron ore In turning back the pages of history, a fascinating story can be told of special interest to the metallurgist, the mining engineer, and perhaps even the sociologist. For, where new communities are planned today, older communities had been born, matured, and died. In these hills had lived the. iron miners, the blacksmiths, the lumbermen, the masons, and the teamsters that had given America its start in heavy industry. This was the area where the forests were crisscrossed with many wood roads that brought logs to the charcoal pits, and iron ore to the furnaces. Men make history. Our story brings forth many names of men known as ironmasters, or as industrial leaders-Hasenclever, Faesch, Erskine, Townsend, Ryerson, Parrott, Cooper, Hewitt, Jay Cooke, and Harriman. The name Sterling is derived from a Scotch Lord, the Fifth Earl of Stirling (in its earlier spelling). Lord Stirling was one of seven Englishmen granted a patent of land in the Ramapo hills by Queen Anne in 1707, known as the Cheesecock Patent. He sent an agent, Cornelius Board, to America in 1730, with the express purpose of looking for copper deposits. While he found no copper in his travels up and down the Ramapo Valley, he did find iron ore in two localities: first, in the vicinity of what is now Ringwood, N. J.; second, five miles to the north. There he constructed a forge and furnace at the edge of a lake in 1736, naming the land Stirling Property, after his patron. In 1740, the Ogden family in Newark bought land from Board at Ringwood and began smelting of iron in 1741. The Ringwood story Soon, a genius in the person of Peter Hasenclever appeared on the scene. He was attracted by an advertisement in the New York Mercury for March 5, 1764, in which David Ogden of Newark offered

Jan 1, 1961

By John Hall

THE Fremont test for measuring the energy consumed in breaking a notched bar of steel is not so well known in this country as it deserves to be. The test specimen used in this test is about 3/8 by 1/4 by about 1 1/4 in., notched with a hack saw on the lower side to cause the piece to break at a fixed point. A weight of 10 kg. falling 4 m., and provided with a knife or chisel which strikes the specimen, breaks the test piece by impact. The residual force in the falling weight after it has broken the specimen is recorded by a suitable device, and the difference between the total energy and the residual energy of the weight (in kilogrammeters) is the force consumed in breaking the specimen. An experience of several years with the Fremont testing machine has shown its great value in readily detecting brittleness not revealed by tensile testing or slow bending testing. I this paper it is proposed to discuss (1) the supersensitiveness of the test as applied to cast steel and (2) its value in revealing the effect of heat treatment under certain conditions. .

Jan 7, 1913

By Owen F. Devereux

Two discrete types of microstructure me seen in cermets formed by the reaction: 4Al (liquid) + 3SiO2 (glass) — 2A12O3(a) + 3Si (solid) Relatively coarse-grained macroscopically isotropic specimens resulted from reaction with aluminum containing appreciable silicon, while macroscopically anisotropic fine-grained specimens were formed by reaction with aluminum low in silicon. Optical microscopy, electron microscopy, and X-ray diffraction suggest that the anisotropic material contains gross areas in which submicroscopic grains of a A12O3 are oriented along radial lines drawn from the specimen surface. These lines are presumed to originate at defects in an otherwise protecting surface layer. A unique cermet is formed by the reduction of high-silica glass by molten aluminum according to the reaction: 4A1 (liquid) + 3SiO2 (glass) — 2A12O3 (a) + 3Si (solid) The free-energy change accompanying this reaction is -150 kcal at 800°C; the volume change (volume of A12O3 and silicon minus volume of SiO2) is +6 pct. The reaction product, however, contains aluminum metal as well as Al2O3 and silicon because some of the product silicon is dissolved in the aluminum bath and is replaced by aluminum in the structure. The product is a hard gray solid that retains the external dimensions of the original silica article. The system has been studied in the past, the investigations culminating in patents to George1, 2 and Saw-chuk., The former emphasize that this reaction is but one of a relatively broad class of such systems, while the latter demonstrates that a marked improvement in the gross physical properties of the cermet can be obtained by dissolving appreciable quantities of silicon in the aluminum reactant. The system has also been studied by workers at Rolls Royce Ltd.,4-6 who have patented the addition of small quantities of arsenic, antimony, bismuth, or phosphorus to the reactant bath to SO impede the reaction that glass fibers may be metal-coated by immersion in molten aluminum.

Jan 1, 1969

Jan 1, 1961

By C. R. Simcoe, T. J. Koppenaal

The effect of direct and alternating currents on the quench aging behavior in an Al-4 pct Cu alloy has been investigated by use of resistivity measurements. The reaction rate increases with direct current density in the investigated range of 1000 to 3000 amps per sq cm. Alternating current of a specific frequency is observed to decrease the reaction rate by a factor of about two. ErDMANN-JESNITZER et al.,1,2 investigated the effect of direct and alternating current on the quench and strain aging behavior of low-carbon iron. In both cases they observed that direct current accelerates the aging reaction and that an alternating current can completely inhibit the aging process. The purpose of the present research was to investigate these phenomena in the quench aging behavior of an Al-4 pct Cu alloy and to determine the correlation, if any, between the increase in the observed reaction rate and possible heating effects accompanying the aging with direct current. EXPERIMENTAL PROCEDURE The aluminum-base alloy used in this investigation contained 3.98 wt pct Cu (1.72 at. pct) with impurities of 0.003 pct Si, 0.002 pct Fe, and 0.001 pct Mg. The alloy was rolled into a ribbon about 0.36 mm thick and 3.7 mm wide. The ribbon was split end from end with the ends being used as electrical contacts and the central unsplit section, about 5.3 cm in length, serving as the specimen. Solution treatment was accomplished by quenching from a salt bath at 520° ± 2°C into water at 25° ±0.5°C; the specimen was immediately transferred to a liquid nitrogen bath. All aging was done at 75° ± 0.2°C in a rapidly stirred ethylene glycol bath. Resistivity measurements were made by the double potentio-metric method employing a standard resistor; for purposes of convenience, the resistance measurements were made at 77°K. The transfer of the specimen from the aging bath to a liquid nitrogen dewar was accomplished in less than 1 sec. The aging kinteics were studied with the specimen being aged under the influence of direct current, alternating current, and without any type of current. The amount of heating caused by direct currents was investigated by soldering a thermocouple on the specimen surface and measuring the temperature change after applying various current densities. The temperature was observed to increase (from 75°C, the aging temperature) about 0.8°, 3.0°, and 8.5°C with direct currents of 1000, 2000, and 3000 amp per sq cm, respectively. When employing alternating current, the circuit was monitored with an oscilloscope and adjustments made to produce a normal sine-wave pattern. RESULTS Prior investigations3'4 in the aging characteristics of A1-4 wt pct Cu have shown that the resistivity initially increases, reaches a maximum, and then decreases to values significantly lower than the as-quenched resistivity. This type of behavior is seen in Fig. 1 which shows the resistivity at 77°K as a function of aging time at 75°C observed in this investigation. At this aging temperature, the resistivity maximum is seen to occur in about 1 to 1-1/2 min and it further decreases to the as-quenched value in about 24 min. The behavior observed with the application of direct currents of 1000, 2000, and 3000 amp per sq cm during aging is shown in Fig. 2. With increasing current densities, (+) ?pmax decreases and the rate of the aging process increases. The time necessary to reach the as-quenched resistivity value decreases from 24 min for aging without current to about 16, 10, and 7 min for aging with 1000, 2000, and 3000 amp per sq cm direct current, respectively. Fig. 3 shows the results obtained when two changes were made during the aging with 2000 amp per sq cm

Jan 1, 1963

By C. B. Foraker

THE Magma mine, of the Magma Copper Co., at Superior, Pinal County, Arizona, is 68 miles east of Phoenix and 21 miles west of Miami, Arizona, on highway U. S. 180. TEMPERATURES AND UNDERGROUND WATERS Surface Temperatures.-The average surface dry-bulb temperature at Superior is 72.4°; wet-bulb, 57.4°; with an indicated relative humidity of 38 per cent. The average yearly rainfall from 1921 to 1936, inclusive, was 18.74 in. The maximum condition of the atmosphere is in June, July and August, and the minimum is in January and February. The surface temperatures, of course, influence the temperatures of the down-cast shafts; however, the variation between winter and summer causes a difference of only 2° to 3° in the stopes and working places that are not close to the intake shafts. Average atmospheric conditions are shown in Fig. 1. Rock Temperatures.-Rock temperatures on the deeper levels of tile mine are as follows: LEVEL DEGREES LEVEL DEGREES 2000 109 3200 127 2250 112.5 3400 130 2550 116 3600 134 2800 120 3800 137 3000 124 4000 140 There appears to be no difference in rock temperature for any particu-lar horizon of the various formations or in the vein. Water encountered is always the same temperature as the rock from which it flows, and for this reason it is thought that the water is heated by the rock; not the rock by the water. The country rock apparently has been heated by the various intrusions, perhaps the vein itself, and has not yet had time to cool off. The geothermal gradient (Fig. 2) as indicated by the rock tem-peratures given above is 1 1/2 ° per 100 feet.

Jan 1, 1938

By E. V. Daveler

THE milling plant of the Alaska-Gastineau Mining Co. is located at the town of Thane, Alaska, on Gastineau Channel, 4 mi. south of Juneau and directly across the channel from the Ready Bullion mine of the Treadwell mines on Douglas Island. Previous to the organization of the Alaska-Gastineau Mining Co., in 1912, the milling was done at the stamp mill of the Alaska Perseverance Co. located at the mine in Silver Bow Basin. But the contemplated increase in production made it necessary to locate the mill on Gastineau Channel, as not enough water was available at the mine during the winter months, nor was there room for taking care of the large tonnage of tailings that would ultimately be discarded from the mill. CHARACTER OF ORE The gold and silver values occur in quartz lenses associated with pyrrhotite, galena, arsenical pyrites, and zinc blende. These lenses occur in large bodies of slate, schist, and metagabbro, which also carry some valuable metallic contents. With the essential low cost of mining, it was necessary to mine large bodies of low-grade material containing the high-grade streaks. Of the minerals, pyrrhotite, the magnetic sulfide of iron, is predominant, and galena is the next sulfide present in quantity. The gold occurs free and coarse and associated with the iron sulfide in its finer state. The silver occurs with the lead or is alloyed with the gold. A chemical analysis of the ore shows Silver 0.10 oz. Magnesia 0.4 per cent. Silica 59.7 per cent. Sulfur 1.2 per cent. Iron 5.2 per cent. Lead 0.1 per cent. Alumina 21.4 per cent. Zinc 0.2 per cent. Lime 5.0 per cent.

Jan 1, 1920

By Walter Harvey Weed

The Republic of Mexico is traversed by many mountain ranges, and presents a great diversity of climates, soils and geographical features, yet its grander geographic provinces are few and peculiarly well defined. The Gulf plain, the Cen tral plateau, the Sierra Madre, and the lowland or Tierra Cali ente of the western coast are the main features of the geogra phy of the Republic, and in the northern half these provinces are particularly well defined. The Sierra Madre separates the Republic into eastern and western parts, and from the City of Mexico north to the Texas line presents an almost impassable barrier to east and west travel. On the north, the first wagon road pass from east to west is at El Paso del Norte, the site of the Texan city of El Paso. Southward for many hundreds of miles the Sierra Madre, traversed by well-worn trails, over which all travel from the west coast to the interior must pass, is a stupendous barrier to social and commercial intercourse. The Sierra Madre is commonly described as a range or con geries of mountain ranges. In fact, it is, in Chihuahua at least, a great plateau, fringed by mountains on the east, trenched by deep canons in its center, and bordered by a wild and rugged complex of mountains carved out of the plateau on the west. Professional duties took me across this region from Parral westward to the Gulf of California via Guadalupe y Calvo. As it includes some of the great ore-deposits of Mexico, and its geological features have never, so far as I am aware, been described, I have prepared a diagrammatic section made from my observations on a horseback trip across the Sierra, and added such notes as seem to be of general interest.

Jan 1, 1902

By E. R. Dean

A wire-feed mechanism has been employed to fabricute metal alloy film resistors to various sheet resistivities on oxidized silicon substrates. The effect of several thousand hours storage in air at elevated temperatures on the resistance and temperature coefficient of resistance is presented. Unprotected films of- sheet resistivity between 100 and 500 ohms per sq fabricated at 300°C substrate tenzperatures were unstable when stored at 150°Cfor extended periods. The higher sheet resistivity films exhibited the greatest instability; however, even the 100 ohms per sq films drijted excessively for device application. When stored at still higher temperatures, the normalized resistance increases to maximum, then decreases until a minimum value is obtained, then finally increases in resistance until open. The use of a protective overcoating of SiO has had considerable benejicial effects on the film stability, so that 250 ohms per sq films deposited on 300°C substrates are now stable after 1000 hr storage at 250°C and possess a temperature coefficient of resistance less than 200 ppm per C. The use of a low substrate temperature during depositon (100°C) enables the preparation oj resistors with very low tenperature coefficients of resistance (10 to 20 ppnl per 'C). However, these films are less stable than their higher substrate temperatuve counterparts. During extended storage, the resistance of the protected films always decreases with lower substrate films exhibiting larger normalized resistance decreases. This resistance decrease is accompanied by a linearly related increase in the temperature coefficient of resistance. The electrical behavior of these films may be explained by postulating That the structure of the films is in the transition region between thick continuous films and ultrathin island structure films so that the conductivity is the restlt of both electron scattering and tunneling-activated charge carrier creation between neighboring grains. The annealing behavior when thermally aged is the result of defect anneal, grain growth, and selective oxidation. TheRE is a considerable interest in thin metallic films for use as resistor elements in microelectronic circuits.1,2 These resistor films must be stable when exposed to elevated-temperature storage or operating ambient, possess low temperature coefficients of resistance (hereafter referred to as T.C.R.), and be of a high enough sheet resistivity to be useful. The resistivity and T.C.R. of a thin metallic film are determined by the structure and thickness of the film. Hence the stability of the film when exposed to stress would depend on the stability of the structure. The resistivity of a thin film is the result of the electrons' interaction with the lattice vibrations (electron-phonon scattering), scattering of electrons due to impurities, defects, and grain boundaries and specula reflection from the film surfaces.3' All of these effects serve to reduce the electron mean free path and result in a resistivity higher than the ideal bulk. In ultrathin films possessing essentially an island structure consisting of a planar array of aggregates separated by a few to a few tens of angstroms, conduction is dominated by a combination of tunneling and activated charge carrier reation. Thin films would be characterized by relatively low resistivity, positive T.C.R., and reasonable structure stability whereas ultrathin films possess unstable structures, negative T.C.R., and exhibit high resistivity. Feldman6 has investigated films intermediate between the two regions and postulates that the resistivity of a film in the transition region is composed of two linearly additive parts: that due to the resistance of the grains and that due to the gaps. The grain resistivity would represent the scattering of the conduction electrons by defects, surfaces, and phonon interaction while the gap term represents the tunneling contribution. For gold and platinum films, he found as the film structure becomes progressively less continuous, corresponding to thinner films, the absolute value of the T.C.R. becomes progressively smaller until negative values are observed with respective zero T.C.R.'s at about 35 and 150 ohm per sq, respectively. Recently the author7 investigated the behavior of a multicomponent alloy of nickel, chromium, and iron and found the T.C.R.'s of these films decrease with decreasing substrate temperature during deposition. The lower T.C.A. associated with lower substrate temperatures was attributed to an increased contribution to the total resistivity from the negatively temperature-dependent gap tunneling since it is well-known that thin films deposited on low-temperature substrates consist of a higher density of smaller grains than the same sheet resistivity films deposited on higher-temperature substrates. Under conditions of thermal anneal, the author found that, when various sheet resistivity films fabricated at 300°C substrate temperature are exposed to extended storage in air at 300°C, the thinner films increase in resistance until open, while the thicker films

Jan 1, 1967

By Sidney Powers

CONTENTS PAGE Distribution of fields 4 History of development 6 Origin of oil 7 Structure,, accumulation and migration 8 Reservoir rocks 9 Methods of drilling and exploration to Oil-field statistics 12 Description by regions: United States: Appalachian region 12 East-central states 17 Kansas 18 Oklahoma 19 Texas 24 Arkansas 32 Louisiana 33 Mississippi -.. 34 Rocky Mountain region 34 California : 37 Canada 41 Mexico 43 Cuba 46 Bibliography 46 THE purpose of this brief account of the occurrence of petroleum in North America is to make available to those who have a knowledge of geology, but who are not engaged in the petroleum industry, a few salient facts about the location of oil and gas fields, their productivity, the important structural types of accumulation and the age of the rocks containing petroleum. A few useful data and statistics are furnished, yet not complete statistics that are available elsewhere. Geology has been treated in simple terms because the reader is presumed to have little interest in the names of formations and of oil sands. Mineral deposits are more or less analogous. Whether oil or metals, minerals are found in rocks, largely in sedimentary rocks which carry water or have at one time carried it. A genetic or accumula-

Jan 1, 1931

By Roger M. Zimmerman

The G-Tunnel heated block experiment is being conducted on the Nevada Test Site (NTS) as part of the Nevada Nuclear Waste Storage Investigations project (NNWSI). The purpose of the ambient temperature testing ph se is to evaluate rock-mass mechanical properties of a block (- 8 m3) under biaxial stress changes up to 7.5 MPa above an initialization in situ value of 3.1 MPa. Results indicate that the modulus of deformation ranges from 9.7 to 17.0 GPa and Poisson's ratio ranges from 0.21 to 0.33. In general, the higher values of the modulus and Poisson' s ratio were influenced by fracture propagations parallel to the compressive stress field. Other measurements indicated that cross-hole compression (p) wave velocities and single fracture permeability values were relatively insensitive to stress changes above the in situ value.

Jan 1, 1984

By William Kelly, F. H. Armstrong

The object of this paper is to describe the electric equipment at the iron-ore mines of Penn Iron Mining Co., Vulcan, Mich. and of Republic Iron Co., Republic, Mich.; to give the results of tests; and to discuss the methods in use from an operating as well as from an efficiency standpoint. Electricity was introduced at the Penn mines for pumping, hoisting, and compressing air in the spring of 1907, upon the completion of a hydro-electric plant built by that company on the Menominee river about 4 miles from the mines. This plant was described in a paper1 presented before the Lake Superior Mining Institute. A paper2 presented at a meeting of the same Institute describes some of the operating features, and the safety devices of the electric hoist at the Curry shaft were briefly described in the Proceedings of the First Co-operative Safety Congress held under the auspices of the Association of Iron and Steel Electrical Engineers at Milwaukee, Wis., Sept. 30 to Oct. 5, 1912. Generating PoweR Plants After the success of electrical operation was assured, a second set of water wheels and generator was installed at the falls, for which provision had been made in the original design and in the construction of the foundations, and later three additional wires were added to the main transmission line, doubling its capacity and reducing the line loss. The general conditions of this installation are particularly favorable for hydro-electric operation. In the neighborhood of three-fourths of the power used is for mine pumping, which in the main is regular and continuous. For air compressing, power is used for about 18 hr. a day for five days, and 9 hr. for one day in the week, though occasionally when shaft sinking is going on a very small amount of compressed air may be

Jan 1, 1915

By W. D. Sylwestrowicz

In tests on polycrystalline copper and aluminum, the ratio of the yield stress to modulus of elasticity was found to be strongly dependent on tempemture. Also, it was shown that the change of the yield stress with temperature of a material at a given temperature and deformed to a given yield stress, but not necessarily to the same strain, does not depend on previous mechanical thermal history. Likewise, for a material at a given temperature and deformed to a given yield stress, the rate of work hardening is independent of the temperature of prior stressing. It has been shown by Los and Orowan1 and by Dorn, Goldberg, and Tietz2 that the temperature dependence of the yield stress-strain curves of crystalline materials reflects two effects: not only does the yield stress of a material in a given structural state depend on the temperature, but the structural state (and the corresponding strain hardening) after a given amount of plastic straining also depends on the temperature at which the pre-straining has been carried out. Thus, for instance, if a specimen of a ductile metal has been strained along the stress-strain curve 1 at room temperature to point A, Fig. 1, and then the straining continued in liquid nitrogen along curve NR, the yield stress A' immediately after lowering the temperature is lower than the yield stress A" of a specimen that has been strained by the same amount in liquid nitrogen (along curve 3). AA' represents the effect of the temperature change upon the yield stress of the specimen pre-strained at room temperature; A' A" is the excess strain hardening acquired if the pre-straining has been carried out in liquid nitrogen instead of at room temperature. The dependence of the yield stress (i.e., of the structural state acquired during preceding straining) upon the conditions (speed, temperature) of a pre-straining is the reason for the nonexistence of a so-called "mechanical equation of state" for plastic deformation. A 'mechanical equation of state" is a relationship of the form F(s,E, e, T) = 0, or s = f(E, E, T) [1] It was first suggested by Ludwik3 that plastic deformation might obey such an equation; this, however, was conclusively disproved by experiments of Kochendorfer.4 Additional disproofs were given in

Jan 1, 1959

By J. Brett, S. Friedman

A study of the diffusion of nickel into both fibrous and recrystallized 0.065-in.-diam silica-alumina doped tungsten wire at 1200°C has been conducted. The diffusion profiles were determined by chemical dissolulion of successive circumferential layers and spectro-photometric determination of nickel in the etchant. It was shown that the diffusion of nickel into tungsten is markedly structure-sensitive. No significant amount of nickel could be introduced at 1200°C into tungsten which had first been recrystallized at temperatures of 2300°C, leading to an upper limit estimate for the bulk diffusivity of nickel in tungsten of 10-11 sq cm per sec at 1200°C. However, nickel did diffuse into initially fibrous wires, caused re crystallization, and was alsays present at the advancing recrystallization front. The accumulation of nickel in an initially fibrous region ceases when the recrystallization front arrives. The characteristics of the resulting diffusion profiles are explained in terms of the relation between diffusion processes and micro structural changes. WHILE it is well-known that the presence of nickel and certain other metals causes low-temperature recrystallization of the cold-worked fibrous structure of doped tungsten,''' the character of the phenomenon is not well understood. Recently it was shown that the recrystallization reaction can be induced at low temperatures by the presence of solid nickel on the surface of doped wire, but not by exposure to nickel vapors.3 Once recrystallization was initiated, a continued source of nickel was required for propagation of the recrystallization front. The phenomenon appeared to be a complicated solid-state reaction since, in addition to the change in structure of the tungsten from fibrous to equiaxed grains, diffusion of nickel from the surface into the recrystallized and fibrous structures was occurring with possible chemical reaction between nickel and tungsten at the surface and interaction of nickel with the dopants which ordinarily stabilize the fibrous structure within the wire. The objective of the present work was to study the diffusion of nickel into fibrous and recrystallized tungsten structures in order to clarify the relationship of the diffusion process to nickel-induced recrystallization. Studies of interdiffusion in the Ni-W system4"7 have been principally concerned with the mobility of tungsten in nickel. Information on diffusion of nickel in tungsten is meager, and there seem to be no studies of the mobility of nickel in tungsten which elucidate the structural aspects of the phenomenon. The present experiments were designed to determine the diffusivity of nickel at 1200°C in fibrous tungsten, in large-grained tungsten prerecrystallized at high tem- perature, and in tungsten recrystallized at 1200°C due to the presence of nickel. Although the concentration profiles were determined in these experiments, unexpected changes in boundary conditions or complex diffusion paths complicated the analysis of these profiles so that the interpretation could not be readily expressed in terms of simple diffusivities. EXPERIMENTAL PROCEDURE The experiments were conducted on Sylvania 0.065-in.-diam silica-alumina doped commercial tungsten wire, hereafter designated as ordinary doped wire. A special lot of 0.065-in.-diam silica-alumina doped low-nickel wire was also used. Impurity analyses of the wire are given in Table I. The experimental design is shown in Fig. 1. All heat treatments were conducted in vacuum. Two groups of ordinary doped wire were prepared for diffusion with nickel. One group in the as-received (fibrous) condition was elec-tropolished, nickel-plated, and annealed at 1200°C for 20 and 40 hr, or was exposed to nickel vapor at 1200°C for 20 and 40 hr. The second group was recrystallized to an equiaxed grain structure at 2300°C for 3 hr, electropolished, nickel-plated, or exposed to nickel vapor for anneals at 1200°C for 20 and 40 hr.

Jan 1, 1969

By W. A. Foster

NINETY years after the Riddle nickel deposit N was discovered in Oregon in 1864, Hanna Coal & Ore Corp. began mining operations. Until 1954 much prospecting and preliminary development work had been done on the property, but no ore had been shipped other than for metallurgical testing. The deposit is being explored by churn drilling and trenching, and a few test shafts have been put down for the purpose of studying the ore in place, determining volume and moisture factors, and gathering bulk samples for pilot plant and smelter tests. In churn drilling, 6-in. casing is driven down 2 or 3 ft behind the drill bit and bottomed at each 5-ft interval. All the sludge for each cased 5-ft interval is dumped through a splitter and one eighth is saved and analyzed. Drillholes are stopped after going through the ore zone and penetrating fresh peridotite in which the nickel content is less than 0.5 pct.

Jan 8, 1957