Search Documents

By D. D. Donald

C. J. Barber (U. S. Smelting Refining & Mining Co., Salt Lake City)—In his paper Donald describes how New Jersey Zinc Co. made surveys for a connection between the Ivanhoe and Van Mater shafts at Austin-ville, Va. Except to say that the two faces had to meet "accurately" on line and grade, Donald does not indicate the required precision. Assuming that there were 24 angles in the 11/2-mile traverse and 15 in the one-mile traverse, it can be shown that if the average error in plumbing each shaft was 230" and the average error in measuring each traverse angle was 210". then the average error at the point of -connection would have been about ±1.9 ft normal to the line between the shafts. This calculation assumes that any errors in the triangulation would be negligible compared with the errors in the plumbings and traverses, and it also neglects taping errors. With no constant errors or blunders, the latter would be important only in lines normal to the line between the shafts. To make the average error at the connection less than 1.9 ft would, therefore, require either reducing the error in the plumbings to less than ±30", or that in the traverse angles to less than ±l0", or fewer stations, or a combination of these. Referring briefly to the triangulation, because of the problem of fitting a new triangulation into older surveys of the district the orientation deserved some mention, even though the connection could have been made with an assumed bearing. It would be interesting to know how many triangles were required and what the average summation error was before making any adjustments and without considering the algebraic signs. Perhaps this is referred to indirectly in the statement that the maximum angular error distributed was 2". Turning to the shaft plumbings, it would be helpful to know how many men were employed and how long each shaft was in use. Donald says that the surface positions of W-2 and W-3 were carefully surveyed from the collar position of W-1, without indicating how this was done. The length of the backsight would be particularly important. There must have been some error in setting W-1 vertically below the stations in the headframes. How immovable were the headframes, especially the Van Mater, which appears higher than the Ivanhoe and subject to more vibration because of skip hoisting? Donald does not say whether the plumbing wires had been previously restraightened to minimize spinning (otherwise they behave like weak helical springs). The use of light steel weights is most surprising because there seem to be excellent reasons for using heavier, nonmagnetic weights. Did the shafts contain no steel sets, pipes, power cables, etc., which might attract steel? The plumbing method described by Donald was designed for deep shafts in South Africa but differed from the South African practice in two important respects. As described by Browne,6 in South Africa the line between the wires was made parallel to the long axis of the shaft, whereas in the Ivanhoe shaft the lines between the wires were diagonally across the shaft. The main reason given for the South African practice is to insure that the gravitational attraction between the wires and the rock walls is the same on both wires, and therefore does not affect the bearing of the line between them. It seems probable, however, that the effect of air currents might be minimized in the South African procedure, and might be serious with the wires in the diagonal position at the Ivanhoe shaft. In the South African case cited by Donald the wires were swinging freely (although the plumb bobs were sheltered from air currents) but in the Ivanhoe case they were dampened with the plumb bobs set in water. In the discussion of Browne's paper R. St. J. Rowland said:' It has been the practice for a long time to damp the oscillations by immersing the bobs in oil or water. The time per oscillation is thus increased, thereby extending the time taken to complete the work. The longer the suspended wire the less there is to recommend the practice . . . The theoretical time for one swing of a simple pendulum 1050 ft long is approximately 36 sec, which would be increased by dampening the plumb bob in water. Hence very few complete swings would be observed in the 5 min intervals used at the Ivanhoe shaft. In the two South African cases described by Browne, the length of plumb line in one shaft was 5425 ft, the calculated period of swing was 81.6 sec, the average actual period was 76.6 sec, and 94 complete swings were observed in 2 hr. In the other case the length of plumb line was 3116 ft, the calculated period of swing was 61.8 sec, the average period was 63.5 sec, and 86 complete swings were observed in 1 hr 31 min. Browne concluded that observations of more than 30 swings are not likely to result in sufficient gain in accuracy to be justified. Returning to the Ivanhoe and Van Mater plumbings, an objection to the method used is that all four azimuths were taken from fixed points instead of swinging wires, and that each pair of observations would— barring blunders— check closely, and so perhaps give a false feeling of security. In fact, it seems that only two azimuths were obtained from one plumbing, and not four as stated by Donald. Nevertheless, the tying in of each pair of wires from both sides of the shaft has much to commend it. Donald's description leaves the impression that if each shaft was plumbed only once, the engineers were fortunate indeed if the average error in the underground orientation was as little as 30". Because the survey was done over a period of three years, it seems likely that the plumbings were repeated, perhaps more than once. The underground traverse angles were measured by conventional methods, but because the number of angles in the overlapping traverses was not given, the angular closure given by Donald does not indicate the accuracy with which this was done. Donald's description of a method of taping lines of irregular length is welcome. The literature on taping is usually confined to lines of about one tape length, generally 100 ft. Such lines are rare in metal mining because the time, trouble, and cost of setting points at 100-ft distances underground are not warranted. (Nevertheless civil engineers may go to this expense

Jan 1, 1960

By Edwin B. Wilson, Charles F. Cockrell

The application of evolutionary operation is proposed for the cleaning of coal by the heavy media process. Analysis of the data given suggests some benefits that may not be immediately appreciated unless evolutionary operation is applied. For example, while it may seem obvious to increase specific gravity when the ash and sulfur content of the clean coal is lower than that allowed, evolutionary operation may show that an increase in feed rate or an increase in both feed rate and specific gravity would be a more profitable alternative. In addition, by using evolutionary operation, up-to-date knowledge of the effect of change of feed rate or specific gravity on yield and product quality is available. This information facilitates confidence about decisions made in regard to the day-to-day operation of these units. A number of other applications in the minerals industry are proposed. An application of evolutionary operation in a related field is also given where a large number of variables were required to be optimized.

Jan 1, 1969

By J. L. SILSBEE

THE existence of large saline deposits in that flat arid basin, known as the Great Salt Lake Desert, has long been recognized, but the extent and great commercial value of these deposits has not been generally appreciated. That a very considerable interest has recently developed is indicated by the fact that about 263 prospecting permits-each covering about 2560 acres of land in this Desert-have been issued under the Potash Leasing Act (Act of 0ct. 2, 1917-40 Stat. 297), and patents granted on approximately 40,000 acres. It is reported that patents and leases have, or will be applied for on an additional 80,000 acres in the basin. , Tests have been made on probably less than 10 per cent. of the total area of the basin, but these have proved a practically unlimited supply of brine available -sufficient, probably, to. furnish the potassium and magnesium chloride requirements of this country for at least a hundred years.

Jan 1, 1925

By A. B., Sabin

THERE are many who know The Lucky Tiger and will remember the 35-mile road from Esqueda, a station on The Nacozari Railroad in northern Sonora, Mexico. They will remember the box canyons of the Agua Caliente Mountains which are scarcely wide enough for two cars to pass; the Bavispe River which one hour may be a lazy trickle and the next a sweeping torrent, and the tortuous road up Tigre and Espuela canyons, now following the wash, now hugging some gigantic red cliff. It is still the same. From camp the view of the distant blue-gray mountains is the same. But one thing a visitor of a former day might miss: The hundreds of pack mules and burros, loaded with concentrates from the mill, which used to take most of the road and show up at the most inopportune places, have almost disappeared, replaced of course by the auto truck.

Jan 1, 1929

By David B. Morris, Paul I. Eimon

Computer-assisted data storage and retrieval in the geosciences is coming of age. A growing awareness of the need of the geological and mining community for effective access to existing data has triggered studies and development programs on many levels; governments, professional societies, industrial concerns, and the academic world are all active in this field. Developments in the past decade in computer hardware and software lend hope to the geoscientist searching for a means of expediting the flow of data. The new concern of the earth sciences coming together with the blossoming child of technology, computing, has led to serious study of the geoscience information problem. Active system development is under way in several areas. The papers presented at this Symposium effectively sample the spectrum of present day activity in machine-based geologic data storage and retrieval. These papers show the reader where the action is in this field today. Both long-range studies and plans and operational systems are discussed. Several studies and research efforts have been undertaken on a national or international scale. Robinson discusses the activity of the international geological community in these Proceedings. He speaks from a position of authority as Chairman of the International Union of Geological Sciences' Committee on Storage, Automatic Processing and Retrieval of Geological Data. A study of a "coordinated information program for geological scientists in the United States" documented by Smith, et al.1 proposes a "long-range information program ... responsive to the entire geosciences community . . . (to) draw on the best of large-scale information systems technology." The European geologic community is embarked on project Geosemantica 70, started at the Ecole Nationale Superieure des Mines de Paris. Dixon discusses some results of this work in a following paper. The Canadian study of geological data storage and retrieval on a national scale is reported in a volume edited by Brisbin and Ediger.2 The Canadian report presents detailed recommendations for recording and coding geologic data for automatic process-

Jan 1, 1969

By Henry Louis

Henry Louis, Newcastle-upon-Tyne, England (communication to the Secretary*).—In this paper Mr. Simons derives the various forms of revolving slime tables, of which the Harz and the Linkenbach tables are typical examples, from the old rectangular or box buddle. This I believe to be an error, at any rate if Mr. Simons attaches the same meaning as I do to the ((evolution" of a dressing appliance. By the '(evolution" of such an appliance I understand the progressive development and improvement of an appliance acting on a definite principle, such improvements having usually for their object the economy of labor in working the same, or the increase of its capacity; when an entirely new principle is introduced, I no longer look upon this as evolution from the old type, but as the origination of an independent type of appliance. The box buddle was no doubt the predecessor of the old Cornish round buddle, which was evolved from it with the object of saving the labor required to work the box buddle; both machines are horizontal-current separators, in which the separation of sands of different densities is effected by their differential rates of fall in a horizontal current of water of considerable depth. These appliances, though well suited to sands, are for obvious reasons not adapted to the treatment of slimes. The revolving tables of the Harz and similar types, on the other hand, act on the principle which I have called separation in thin films of water, and which Mr. Simons calls the film sizing principle, in which the resistance of the surface over which the pulp flows plays an essential part in determining the separation of the particles, and which is well suited to the treatment of slimes. Unlike the last principle, it will not work in deep bodies of water and cannot be used where considerable depth of material accumulates in the appliance, as in the box buddle and round buddle. As I have shown in my book, The Dressing of Minerals, p. 326, these revolving tables are a development of the appliance known variously as the flat buddle, flat table, or frame, the last name, which is the old Cornish one, being the one that I personally prefer. These primitive appliances, as well as the continuous-acting round tables described by Mr. Simons (his Figs. 10 et seq.) all work on the principle of separation in thin films, and are all adapted for the treatment of slimes; his buddles and round tables (Figs. 1 to 9) do not work upon this principle, and should therefore be sharply differentiated from the former. The evolution in each case of the continuous acting, more or less automatic, circular appliance from the primitive, intermittent, hand-worked, rectangular appliance has proceeded upon strictly parallel lines. The question of the evolution of the respective types involves a point of some importance as regards the principles of ore dressing.

Jan 1, 1915

By Louis D. Huntoon

(New Haven Meeting, February, 1909.) THE Hammond Mining and Metallurgical Laboratory is the gift of Prof. John Hays Hammond to the Sheffield Scientific School of Yale University. Professor Hammond was graduated from this school in the class of 1876, and has always shown great interest in its welfare and progress. In 1903, he offered to build and equip for it a mining and metallurgical laboratory. This offer was gratefully accepted by the trustees; and in October of the same year the architect, W. Gedney Beatty, and the writer were employed to draw up plans for the building, which is the largest of its kind in this country. The Treasurer's report shows the total gift of Professor Hammond, including land, building, and equipment, to have been $128,741.53. This does not include $5,000 given by Professor Hammond to defray incidental expenses. The detailed cost of the machinery and installation, included in the above sum, is as follows: Machinery, $9,846.00 Pipe and fittings, 925.05 Hangers, shafting, pulleys, belts, etc., . 357.83 Steel-work, tanks, launders, etc., . 272.19 Screens for sizing ore, 411.37 Lumber, 1,896.36 General Supplies Hardware, . $135.96 Tools, 263.66 Paints, . 04.63 Electric and incidental, . 439.57 - 1,043.82 Machine-shop material, 259.44 Labor, 722.29 - 981.73

Mar 1, 1909

By C. A. Pierce

Studies of roof and floor movement are of interest to those actively engaged in mining. This is especially true in the case of an entirely new area where there is no precedent for guidance. The potash deposit being mined is in the southeast corner of New Mexico, about 20 miles east of Carlsbad. The deposit was formed by the land-locked, shallow, Permian Sea that extended through parts of western Texas, Oklahoma, Kansas, southeastern Colorado, and eastern New Mexico. The saline deposits vary from 500 to 4000 ft. thick. Neither of the companies operating in this area has delimited its commercial ore bodies. As all production so far has been from Federal and State leases, the Department of the Interior and the State of New Mexico have a direct interest in the development and extraction of these ore horizons. The ore is composed of an intimate mechanical mixture of sylvite (potassium chloride) and halite (sodium chloride). It lies generally in a horizontal bed varying from 5 to 12 ft, in thickness, and has a cover of approximately 1000 ft., consisting of about 500 ft. of salt beds and 500 ft. of sediments. The immediate mine roof for several feet is principally salt with some potash and clayey material. The next 500 ft. above, from the standpoint of structure, may be considered rock salt with a few inter-bedded potash members. The upper 500 ft. is of sedimentary (Permian and Triassic) origin and contains several water-bearing formations with flows varying from 10 to 500 gal. per minute. This water intensifies the interest in convergence problems as the ore and surrounding formations are water soluble. Potash salt (sylvite) and rock salt (halite) are plastic minerals. Plasticity is defined as a "property of solids by virtue of which they hold their shape permanently under the action of small shearing stresses but are readily deformed, worked, or molded under larger stresse."1

Jan 1, 1942

By C. A. Pierce

Studies of roof and floor movement are of interest to those actively engaged in mining. This is especially true in the case of an entirely new area where there is no precedent for guidance. The potash deposit being mined is in the southeast corner of New Mexico, about 20 miles east of Carlsbad. The deposit was formed by the land-locked, shallow, Permian Sea that extended through parts of western Texas, Oklahoma, Kansas, southeastern Colorado, and eastern New Mexico. The saline deposits vary from 500 to 4000 ft. thick. Neither of the companies operating in this area has delimited its commercial ore bodies. As all production so far has been from Federal and State leases, the Department of the Interior and the State of New Mexico have a direct interest in the development and extraction of these ore horizons. The ore is composed of an intimate mechanical mixture of sylvite (potassium chloride) and halite (sodium chloride). It lies generally in a horizontal bed varying from 5 to 12 ft, in thickness, and has a cover of approximately 1000 ft., consisting of about 500 ft. of salt beds and 500 ft. of sediments. The immediate mine roof for several feet is principally salt with some potash and clayey material. The next 500 ft. above, from the standpoint of structure, may be considered rock salt with a few inter-bedded potash members. The upper 500 ft. is of sedimentary (Permian and Triassic) origin and contains several water-bearing formations with flows varying from 10 to 500 gal. per minute. This water intensifies the interest in convergence problems as the ore and surrounding formations are water soluble. Potash salt (sylvite) and rock salt (halite) are plastic minerals. Plasticity is defined as a "property of solids by virtue of which they hold their shape permanently under the action of small shearing stresses but are readily deformed, worked, or molded under larger stresse."1

Jan 1, 1942

By Marcel Schlumberger

The electrical methods for surface-prospecting have been well developed in the last 20 years. The method involves, in the classic form, the sending of an electrical current into the soil, by means of two electrodes A and B, and studying the potential distribution at the surface, by measuring the difference of potential between pairs of points such as M and N. The points M and N are usually placed on a line between, and equidistant from, A and B. By increasing the distance AB, the current sent into the Earth, and likewise the distribution of surface-potentials, become influenced by regions of greater and greater depth below the surface. By varying the form and dimensions of the electrode-arrangements AMNB, called a "quadripole," one may make valuable deductions concerning the nature or thickness of beds, if one knows the electrical properties of these beds. On the other hand, if the form and dimensions of the electrodes AMNB remain fixed, the depth of penetration of currents in the Earth remains, so to speak, almost constant, although it tends to increase where the subsoil is more conductive, and conversely. Therefore, if one moves the constant-dimension quadripole over all the terrain to be Investigated, one achieves approximately a horizontal exploration. This permits a study of tilted beds or faulted horizon-tal beds. When the particular problem becomes deep, of the order of 2000 meters, or more, it is ne-cessary to Increase the distance between the current-sources AB to a length such that the work 'comes very troublesome, especially if the region is wooded. At the same time, the separation the points M and N must be likewise great (for example, one km) in order to obtain differences potential which are not too small; the measurement of potential differences across MN is then difficult because of the presence of parasitic potentials, due to a flow of telluric currents in fourth, and the order of greatness of these currents may exceed the quantities to be measured.

Jan 1, 1940

This issue presents the first of several articles making up the Bump Symposium, which was held at the 1958 Annual Meeting of AIME. Other Symposium papers will appear in the September issue of Mining Engineering. THE term mountain bump describes the sudden rupture of one or more coal pillars under excessive stress. These bursts occur with varying degrees of violence and sometimes include adjacent strata, especially the bottom rock. Many failures do not develop enough violence to be dangerous and are regarded as an aid to coal production, but severe occurrences are accompanied by tons of flying coal, dense clouds of dust, and excessive gas emission. Such bursts sometimes throw heavy machinery several feet. Major factors to be considered in the problem are the nature of the strata above and below the seam and the depth of cover. Bumps are classified as to their nature, extent of damage, and point of occurrence, e. g., face bump, coal bump, high side bump, low side pavement bump, and district bump. The problem is extremely complex, and it cannot be over-emphasized that preventive measures, if they are to be successful, must be based on a thorough study of conditions in the individual mine. In western Canada, for example, the McGillivray mine, operating in a 9-ft seam at 2000 ft, has experienced severe bumps, but there have been no occurrences in the International mine, which operates in the same coal seam at 2400 ft, where the coal averages 17 ft thick. Differences in conditions governing the operation of these two mines are described in one of the following articles (see page 883). Again, most bumps in coal mines take place along pillar extraction lines, but at the Sunnyside mine in Utah they also occur a long way from active workings and sometimes in virgin territory. It is usual, too, for such failures to occur under fairly deep cover. But at Sunnyside, to cite only one instance, there have been disturbances along the main fault zone under less than 500 ft of cover. All too often conditions favorable to bumps are revealed only by actual mining—at Springhill No. 2 mine, drilling in roof and pavement strata disclosed a 60-ft sandstone bed after operations had started— and where extraction has advanced too far for preventive measures to be incorporated in the mining plan, districts have had to be abandoned. But in an era when premium ores are being rapidly depleted in the face of rising demands, abandonment is not easily justified. There must be systematic planning to eliminate coal mine bumps, insofar as this is possible. As in the Gary district of West Virginia (see page 888) much has been accomplished by planned operations based on known factors in bump control. But even this is not enough. Precise instrumentation is needed to indicate where bumps are likely to occur, and in both the U. S. and Canada stress analysis studies are being carried out with this object in view. These pages reveal the progress being made.

Jan 1, 1959

By AIME

A GEOLOGIST --one versed in geology, the science which treats of the history of the earth and its life, especially as recorded in the rocks; that is Webster's definition. William Embry Wrather-one of the country's foremost geologists who heads the U. S. Geological Survey; this is the 1948 President of the Institute. He has studied the geology of areas on the face of the earth as far-flung as Texas and the Balkans, and now heads the world's largest staff of geologists. Vital statistics on Dr. Wrather would show his place of birth as Brandenburg, Ky., the year 1883. He will celebrate his threescore and five years of full living the twentieth of this month. As is usual in biographical sketches of this nature, the formative years of youth, and in many ways the most important years of one's life (since professional tendencies as well as many important personal decisions are evidenced before the teens are left behind) are passed over with the mere fact noted that a degree was earned at such and such educational institution. And so we note that Dr. Wrather received his Ph.B. degree at the University of Chicago in 1907, and followed up that degree with two years of graduate study.

Jan 1, 1948

By AIME AIME

PERHAPS the outstanding characteristic of the newly elected President of the Institute is his rare ability to set aside nonessentials, and pick out the few basic elements on which a valid conclusion on any question can be drawn. This holds whether he is appraising a mining enterprise, selecting a man for an important position, deciding whether to buy or sell a bond, or choosing the best method for mining a huge body of ore. For example, he has pointed out that the two primary factors that make for success in a copper-mining venture are a large reserve of reasonably good ore and competent management. Usually the first is not as difficult to gauge accurately as the second. In a big enterprise the quality of the management

Jan 1, 1939

By Benjamin Miller

FROM earliest recorded times, limestone has been employed in the industrial life of peoples of all sections of the world where it exists. It is widely distributed and therefore has been available in almost every country and has been employed for a variety of purposes. Its earliest use was for buildings, since it is more easily quarried and dressed than most other kinds of rocks and so could be utilized by early inhabitants, poorly equipped, with tools. The next use was in the manufacture of lime, which was employed by the ancients in mortar. These two uses of limestone are still all important, but they have been overshadowed in scores of regions by literally hundreds of new applications for raw lime-stone or products made from it. Anyone familiar with modern manu-facturing processes can quickly call to mind many industries in which limestones are essential, and new uses are continually coming to notice. Any enumeration would probably be incomplete and soon out of date.

Jan 1, 1935

By F. X. Tartaron

This article is a continuation of a previous paper by the writer in which Kick's Law was stated to be a part of comminution theory. ln the present paper, a broadening of ideas is attempted in order to state a general theory. The word "general" is employed because the new theory includes all previous laws and generalizations which are considered to be essentially correct. These ideas are combined into a coherent whole and the general theory can be expressed by the equation In the author's previous paper on comminution, ' the equations developed were based on Charles' equation of exponents a-n +1 = 0. 2 This paper is divided into two parts, designated as First Approach and Second Approach. In the First Approach, the equations of the previous paper are utilized, with Charles' equation of exponents being necessary. In the Second Approach, a separate and independent method is used to derive the same conclusions as in the First Approach, but without the use of Charles' equation of exponents. Holmes accepts the theoretical foundation of Kick's Law as sound but denies that the law as such operates in comminution. His idea is that Kick's Law requires homogenous matter whereas the presence of cracks, flaws and cleavage planes, which predominate in the coarser particles, makes matter unhomogene-ous. This explains why there is no experimental evidence to support Kick's Law. However, since the basis of the law is theoretically sound, all experimental evidence must be viewed as emanating from it. This requires modification of current comminution equations to fit this concept. Holmes makes the modification by changing the constant exponent n in the general energy equation used by Charles (E = - JCdx/xn) to a variable exponent r. The writer asserts that Kick's Law operates in comminution without modification but it does not

Jan 1, 1963

By J. Murray Riddell, George A. Morrison

This paper is a companion to the one by George A. Morrison on Mining a Deep Limestone Mine in Ohio.‡ Barberton is 8 miles west of Akron, Ohio, and 23 miles south of Cleveland. The underground mining of limestone at Bar-berton constitutes the world's deepest limestone mine. The stratigraphy is as follows: 0-20 ft. Loam, clay, sand and gravel. Water bearing. 2-40 ft. Fractured sandstone. Water bearing. 40-110 ft. Sandstone with interbedded shale, slightly fractured. Water bearing. 110-314 ft. Sandstone with interbedded shale, slightly fractured. Water carrying. 314-2197 ft. Shale with occasional seams of sandstone, which varies in thickness from a few inches to 4 feet. Dry. 2197-2247 ft. Limestone. Dry. 2247-2742 ft. Dolomitic limestone. Dry. 2742-2767 ft. Salt. Dry. 2767- Dolomitic limestone. Dry. All of the strata dip to the southeast, about 0.5 per cent from the horizontal. The top 110 ft. of the crust is water-bearing. The rock strata are naturally fractured to a depth of 314 ft., sufficient to allow the passage of water. In the shaft-sinking operations, a stra- turn of oil-bearing sandstone one foot thick was encountered at a depth of 520 ft., and flows of methane gas were pierced at depths of 1350 and 1952 feet. Specifications for the mine plant called for, in part, the sinking of two vertical shafts and a hoisting plant capable of producing at the rate of 300 tons per hour. No. I shaft is 550 ft. west of No. 2 shaft. Each shaft measures 8 by 17 ft. outside of steel. General features of the design (Fig. I) are: Principal set members, 6-in. H-section; connecting angles (studdles), ? by 4 by 4-in. angle irons; spacing of sets. 8 ft. centers; spacing of bearer sets, generally, 160 ft.; bearers, of 12-in. I-beams. Each bearing set featured a concrete ring about the periphery of the shaft, steel to rock, and 8 ft. in height; permanent guides, 6 by 10-in. long-leaf yellow pine, 85 per cent heart. The Shaft-sinking Operation The preliminary shaft-sinking work consisted of driving interlocked steel piling about the exterior of the shafts to depths of 35 and 32 ft., respectively, and of such horizontal dimensions as to ultimately permit the pouring of a concrete collar 2 ft. in horizontal thickness. Following the pouring of a shaft collar, a temporary wooden headframe for shaft-sinking purposes was erected. The head-frame, while ordinary, featured: (1) a storage pocket of 300 cu. ft, capacity with truck servicing facilities, and (2) pneu matically operated dump doors, which mere actuated by the hoistman, thus caring

Jan 1, 1946

By J. Murray Riddell, George A. Morrison

THIS paper is a companion to the one by George A. Morrison on Mining a Deep Limestone Mine in Ohio.[+] Barberton is 8 miles west of Akron, Ohio, and 23 miles south of Cleveland. The underground mining of limestone at Barberton constitutes the world's deepest limestone mine. The stratigraphy is as follows: 0-20 ft. Loam, clay, sand and gravel. Water bearing. 20-40 ft. Fractured. sandstone. Water bearing. 40-110 ft. Sandstone with interbedded shale, slightly fractured. Water bearing. 110-314 ft. Sandstone with interbedded shale, slightly fractured. Water carrying. 314-2197 ft. Shale with occasional seams of sandstone, which varies in thickness from a few inches to 4 feet. Dry. 2197-2247 ft. Limestone. Dry. 2247-2742 ft. Dolomitic limestone. Dry. 2742-2767 ft. Salt. Dry. 2767- Dolomitic limestone. Dry. All of the strata dip to the southeast, about 0.5 per cent from the horizontal. The top 110 ft. of the crust is water-bearing. The rock strata are naturally fractured to a depth of 314 ft., sufficient to allow the passage of water. In the shaft-sinking operations, a stra was encountered at a depth of 520 ft., and flows of methane gas were pierced at depths of 1350 and 1952 feet. Specifications for the mine plant called for, in part, the sinking of two vertical shafts and a hoisting plant capable of producing at the rate of 300 tons per hour. No. I shaft is 550 ft. west of No. 2 shaft. Each shaft measures 8 by 17 ft. outside of steel. General features of the design (Fig. I) are: Principal set members, 6-in. H-section; connecting angles (studdles), 3/8 by 4 by 4-in. angle irons; spacing of sets, 8 ft. centers; spacing of bearer sets, generally, 160 ft.; bearers, of 12-in. I-beams. Each bearing set featured a concrete ring about the periphery of the shaft, steel to rock, and 8 ft. in height; permanent guides, 6 by 10-in. long-leaf yellow pine, 85 per cent heart. THE SHAFT-SINKING OPERATION The preliminary shaft-sinking work consisted of driving interlocked steel piling about the exterior of the shafts to depths of 35 and 32 ft., respectively, and of such horizontal dimensions as to ultimately permit the pouring of a concrete collar 2 ft. in horizontal thickness. Following the pouring of a shaft collar, a temporary wooden headframe for shaft-sinking purposes was erected. The head-frame, while ordinary, featured: (I) a storage pocket of 300 cu. ft. capacity with truck servicing facilities, and (2) pneumatically operated dump doors, which were actuated by the hoistman, thus caring for the dumping of the "ball-and-chain"

Jan 1, 1944

By ElRoy Nelson

WATER provides to many mineral industries functions similar to those performed by money in the economic system. Water is a medium of exchange. It is also required in chemical reaction for cooling, for transfer of minerals, and for cleaning. To a great extent, water is also a raw material in almost every industrial operation; it becomes a component of the finished product. In the Rocky Mountain region, water is treated with a great deal of respect. There has not been enough of it when needed. Long ago storage facilities were planned and devised to assure a supply during periods of shortages. This comes from the history of the region in irrigation and mineral processing. Within this region the shovel was always the most lethal weapon used in settling disputes over the use or misuse of water.

Jan 10, 1954

By Shiou-Chuan Sun

THERE are several postulations for the mechanism of slime-coating. Ince1 proposed the electrostatic hypothesis, del Giudice2 suggested the chemical theory; Bankoff3 reported that slime-coating is inhibited whenever the surfaces of the slime particles are ionized sufficiently for Brownian movement to occur, and is facilitated when they are not. These postulations were examined by experiments involving the Burton tube, the cataphoretic cell, and slime-coating. The techniques involved will be described elsewhere in this paper. The electrostatic hypothesis, supported by migration experiments in a Burton tube, was abandoned by del Giudice.2 Experiments of mineral migration in a Burton tube, after the idea of Ince with modification, indicated that this apparatus was inefficient for accurate observation. A cataphoretic cell was constructed. The experimental data, as shown in this paper, enable the correlation and advancing of this hypothesis. Del Giudice's chemical hypothesis considered that slime particles are attached to the galena surfaces by a cement formed as the result of a metathetical reaction between the sulphide and the slime particles. Applying this hypothesis, the calcite slime particles were cemented to the galena surface by the formation of a cementing lead carbonate. In a similar way, lead silicate was considered as the cement of quartz slime coating on galena. Experiments verifying this hypothesis were carried out according to the following procedure: Fresh mineral particles selected from the central part of the broken lumps and examined first under a microscope for ascertaining a clean surface were placed in a small beaker (1.5-in. dia. by 2.5 in. deep) half filled with one kind of slime pulp. The dilution of all slime pulp was 4: 1 and the particle size of slime was minus 400-mesh. After agitation for 5 min. the specimen was removed by a sharp-end tong and washed gently three times in three separate distilled water baths. It was dried before a small electrical fan and examined immediately under a microscope. A photograph was made of the observation. With reference to the published solubilities,4 several of these experiments, which contradict the chemical hypothesis, are listed as following: I. The coating of fluorite slime on the galena surface was light but the coating of galena slime on the fluorite surface was heavy. In a similar way, the coating of quartz slime on the galena was fairly light, but the coating of galena slime on the quartz particle was heavy. According to the chemical hypothesis, using the same constituents and regardless of which is the slime, the density of the coating should be expected to be the same. This, however, as shown above, is not true. Moreover, fluorite (CaF2), having a solubility of 16 mg.[4a] per liter of water, should not be

Jan 1, 1943

By Tracy C. Jarrett

In 14-karat gold alloys, as in 10-karat gold alloys,3 the addition of such metals as zinc, nickel, copper and silver produces a wide range of physical and chemical properties such as color, hardness, corrosion resistance and melting points. These important factors made gold alloys desirable in the optical work and for jewelry. In 14-karat gold alloys, as well as in 10-karat or 12-karat, it is possible to have two golds of the same color, one of which will corrode more than the other, although it may be harder. Some of these alloys have been investigated by F. E. Carter,' E. M. Wise,= and L. Sterner Rainer.4 In this group of alloys the gold content of 58.3 per cent (14-karat) was held constant, while the copper varied from 36 to 24 per cent. The balance of the alloy consisted of one, two, or three of the metals silver, zinc, and nickel. All the alloys were melted in an induction furnace and cast into an ingot that measured 3 by 1/4 by 3/4 in. The method of determining the melting points, color determinations and acid test have been discussed in previous papers by the author.2, 3 It is necessary to use small test bars (Fig. I). The tensile bars were annealed at 1300oF. for 20 min. and then air-cooled. There being a very marked drop when the yield point was reached, "the drop of the beam" method was used in determining the yield point. Alloys Gold-copper.zilzc A~loys.—Gold-copper-zinc alloys melt, cast, and labricate easily. The low melting points, however, limit their use to some extent. The physical properties of these alloys are not entirely satisfactory. When the ultimate strength is satisfactory, the elongation and reduction of area are too low (Table I). Gold-copper-sinr-nickel A lloys.—In this group of alloys, in which zinc and nickel replace copper in approximately equal parts (Table I), the yield point, hardness, and ultimate strength increase with the increase of zinc and nickel content, while the reduction of area and elongation decrease. The physical properties are desirable, particularly of the white gold alloys. The alloys of this group are not difficult to cast and fabricate, and most of these colors could be used commercially. Gold-copper-nickel A lloys.—Gold-copper-nickel alloys are similar to the gold-copper-zinc and the gold-copper-zinc-nickel alloys. They do, however, possess high yield point, ultimate strength and hardness, somewhat higher than those of the other two groups mentioned (Table I). The difficulty with these alloys is that they fire-crack readily and heavy rolling is necessary between annealings. Being hard to fabricate, many

Jan 1, 1941