Search Documents

By G. R. Countryman, G. H. Thomas, I. Fatt

Procedures are described for scaling up turbulent friction pressure drops of inelastic fluids and laminar friction pressure drops of inelastic/elastic fluids in circular ducts. The laminar scale-up calculation method does not require the use of arbitrarily defined flow models, and can be performed directly from laminar capillary viscometry data, or by means of a numerical solution of the integral equation for Poiseuille flow, inputing true shear rate-shearing stress data from other simple shearing experiments. e.g. Couette and plane Poiseuille flows. The turbulent scale up procedure, based on the Dodge-Metzner correlation for inelastic fluids, requires evaluating the characteristic rheological parameters at the existing wall stress under laminar flow conditions. Since the wall stress is the quantity sought in a pipe flow scale-up problem, a trial-and-err or solution is indicated, and therefore a calculation method has been developed and programmed for a medium-size magnetic-drum-memory digital computer. Laminar flow data from other somces may also be adapted to this turbulent scale-upmetbod for inelastic fluids. Comparisons between predicted and experimentally observed friction losses for generalized Reynolds numbers ranging from 3 — 32.000 indicate an error band width of less than 10 per cent in circular tubes ranging in size from 0.5 to 1.89 in. in diameter. INTRODUCTION Considerable effort has been devoted to the problem of establishing an accurate procedure for predicting the laminar and turbulent flow behavior of non-Newtonian materials in pipes from data obtained with small scale laboratory or pilot plant equipment, as evidenced by the variety of reviews on the subject.1-3 Although there does not appear to be a universally accepted scale-up method for laminar flow, the various methods currently employed can be divided into two principal categories depending upon whether a functional relationship between shear rate and shearing stress is assumed, or whether a generalized correlation is adopted. The methods of Hedstrom4 and of Weltmann are typical of the first category, while the generalized correlation of Metzner and Reed6 illustrates the second category. Under appropriate conditions either approach yields a reasonably satisfactory description of laminar flow behavior. In contrast, the prediction of non-Newtonian transitional and turbulent friction losses is much more complex. For example, certain types of materials have been observed to sustain laminar flow at much higher flow rates than Newtonian liquids. When turbulence does develop, the level of agitation is damped to such an extent that the friction factor is lower than that of the original low viscosity Newtonian medium. Extremely broad transition regions and "diameter effects" have also been noted in the turbulent flow of certain chemically complex materials.' Aside from the latter complications, which are attributed in part to viscoelasticity, the existence of a variety of scale-up procedures for predicting transitional and turbulent friction losses is due principally to the chioce of viscosity parameter used in the definition of the Reynolds number. In contrast, Dodge and Metzner have demonstrated that the friction factorReynolds number relationship for inelastic fluids can be satisfactorily generalized provided the fluid property parameters are evaluated at the existing wall shearing stress.* However, the quantity usually sought in a pipe flow scale-up problem is the wall stress, and hence a trial-and-error procedure is required when dealing with non-power law materials. In this report we discuss two calculation methods: (1) for determining the wall stress, and hence the friction pressure drop, for inelastic fluids under conditions of turbulent flow by means of an iterative procedure, and (2) for predicting laminar friction pressure drops without recourse to arbitrarily defined flow models.

By R. F. Steigerwald

The effects of heat transfer on the corrosion behavior of type 304 stainless steel in boiling water have been studied. Heat transfer conditions increase the tendencies of the stainless steel toward stress-corrosion mucking when the water is contaminated with Cl-. Surface preparation is the most important variable in determining the severity of the stress-corrosion problem in water with a given Cl- content. Heat treatment, chemical cleaning, and degree of wet film boiling also affect the corrosion of stainless steels used as heat transfer surfaces in boiling water. An up-paratus for corrosion testing under controlled heat transfer conditions is described. THE principal objective of this investigation was to study the corrosion behavior of AISI Type 304 stainless steel in boiling high-purity water under conditions of heat transfer. The principal variables in the study were: a) boiling conditions: limited boil, agitated boil; b) metallurgical structure: annealed or sensitized; c) surface condition: rolled, pickled, or ground. The results of the study should elucidate the role of heat transfer in the corrosion of stainless steel in boiling high-purity water and provide a base line from which to assess the severity of this type of corrosion. Although there has been an investigation of the effect of heat transfer on the corrosion behavior of stainless steels in alkaline waters,' work on the corrosion of stainless steels under heat transfer has been largely confined to various acid solutions.'-4 Furthermore, the study of the corrosion of stainless steels in high-purity water has been generally restricted to auto-clave and instream testing in superheated (e.g., 300°C) water and steam.5'6 Cooling water problems led to this study of the corrosion behavior of type 304 stainless steel in high-purity water at its atmospheric boiling point. In addition to the effects of heat transfer, this study also considered the influences of the type of boiling,7 metallurgical structure, and surface condition on the corrosion behavior of stainless steel in high-purity water. Two boiling conditions were investigated in this study: a) limiting boiling, i.e., when the heat-transfer surface had just reached the boiling point and boiling nucleated randomly over the specimen surface and b) agitated boiling, i.e., when a mild degree of superheat had been achieved on the specimen surface and boiling occurred generally over the specimen surface. Both boiling conditions are broadly classified as wet-film boiling. Originally, this program included the study of a third type of boiling, dry-film conditions. At dry-film boiling the temperature of the heat transfer surface is high enough so that it is covered with a continuous film of steam. Experimental difficulties made it impossible to study this kind of boiling with the available apparatus. Since surface condition affects heat transfer rates, three typical surfaces were chosen for study: a) as-rolled, the 2B finish received from the supplier, b) as-pickled, 30 min in 8 pct HNO3-1 pct HF, and c) as-ground on 120 grit paper. In order to evaluate the effect of improper heat treatment or welding on hot wall corrosion, both annealed and sensitized mi-crostructure were included in this study. EXPERIMENTAL Test Apparatus. The particular problems of interest in this investigation required a knowledge of the thermal gradient through the test specimen. From this gradient, the heat flux to the surface and the surface temperature could be determined. In order to satisfy this need, an apparatus similar to the boiling-disk apparatus of Fisher and whitney2 was designed. The solution is contained in a thermally-insulated, steel pipe lined with TEFLON resin. A stainless steel _______;________________________________________

Jan 1, 1970

By Henry D. Hibbard

FoR the purpose of this paper all steels will be divided into two divisions: effervescing and non-effervescing. This classification must be borne in mind as many statements true of one class are not true of the other. Effervescing steels are those that effervesce in the molds, evolving large volumes of gases, which, in escaping, throw up a spray of molten particles of steel and give the molten metal in the mold a rapid stirring or churning motion until it freezes, or, at least, becomes pasty. This effervescing is intended and proper. The non-effervescing steels, which are more or less completely killed, should not evolve any gas in the molds. Many years ago the writer proposed to call the two classes of steels evolution and solution steels, depending on whether the gases in the molds are evolved or kept in solution, but the present designations seem to be better. In America, at least, effervescing steels are in a class by themselves and include steels made for boiler, tank, and ship plates, steel pipe, soft steel wire, wire nails, soft machincry, and structural steels. These are all low-carbon steels with less than 0.40 per cent. carbon. Low-carbon steels that do not effervesce but are killed are also made; these are put into ingots and castings but they are outside the limits of this paper. Effervescing steel is cast into square or slab molds, either top or bottom poured. Most of the effervescing steel is made in the basic open-hearth furnace, though much is made by the acid Bessemer process and a little is made in the acid open-hearth. It is not made by the crucible or electric-furnace process, in which the volume of gas required cannot be produced in the steel and evolved from it in the mold to give the effervescence desired. Any steel ingot, when teeming is finished, is of a certain size or volume. Leaving out of consideration for the moment the lessening of the over-all dimensions of the ingot through contraction due to loss of heat, the ingot may be placed in one of three classes: It may settle, losing in volume; it may stand, that is, remain constant in volume; it may rise, that is, increase in volume. Into which class an ingot will fall depends on the gases of the steel,

Jan 1, 1920

By Adrian E. Ross

Diamond drilling through caving formations at depths greater than ZOO0 ft has long presented serious difficulty, generally solved either by casing or cementing. Casing is permitted only when the resulting smaller hole is acceptable, and cementing is frequently a problem at depth. A new method that injects cement under pressure at the desired location is an aid in diamond drilling deep holes. DRILLING through caving formations in diamond drill holes at depths greater than 2000 ft has long been a serious problem. These caving formations are normally passed only by casing the hole or by cementing the hole. Casing the hole is possible only when a resulting smaller hole is acceptable. In as much as only a limited number of reductions are economically practical, cementing is frequently considered the only method suitable for solving these problems. Cementing either by pumping a slurry into the hole or by dropping cylinders containing cement has proved satisfactory on holes under 2000 ft. In holes substantially deeper than 2000 ft these methods are not satisfactory, since during the pump- ing process cement separates out, whereas cylinders usually break before the bottom of the hole is reached. A new procedure, the injector method, apparently solves these problems.* With this method, cement is lowered in the hole in a cylinder, the cement being

Jan 1, 1953

By Adrian E. Ross

Diamond drilling through caving formations at depths greater than ZOO0 ft has long presented serious difficulty, generally solved either by casing or cementing. Casing is permitted only when the resulting smaller hole is acceptable, and cementing is frequently a problem at depth. A new method that injects cement under pressure at the desired location is an aid in diamond drilling deep holes. DRILLING through caving formations in diamond drill holes at depths greater than 2000 ft has long been a serious problem. These caving formations are normally passed only by casing the hole or by cementing the hole. Casing the hole is possible only when a resulting smaller hole is acceptable. In as much as only a limited number of reductions are economically practical, cementing is frequently considered the only method suitable for solving these problems. Cementing either by pumping a slurry into the hole or by dropping cylinders containing cement has proved satisfactory on holes under 2000 ft. In holes substantially deeper than 2000 ft these methods are not satisfactory, since during the pump- ing process cement separates out, whereas cylinders usually break before the bottom of the hole is reached. A new procedure, the injector method, apparently solves these problems.* With this method, cement is lowered in the hole in a cylinder, the cement being

Jan 1, 1953

The President was authorized to appoint a committee comprising himself and five others, to draft an amendment to the Constitution for the purpose of bringing before the membership the suggested change in qualifications for members. The President thereupon appointed the following Committee: Edwin Ludlow, Chairman, B. B. Thayer, J. W. Richards, G. C. Stone, C. F. Rand, and P. N. Moore. The President was authorized to arrange with the Bureau of Mines for the payment of the necessary clerical assistance to copy the inventory of

Jan 8, 1917

"Acta Metallurgical, C E Birchenall, Dec '58 Alfred Noble Joint Prize Committee F B Foley, Dec '61 American Association for the Advancement of Science J T MacKenzie, Dec '58, 0 B J Fraser, Dec '57 American Geological Institute Charles F Park, Oct '58, Arthur Montgomery, Oct '59 Committee on Government Relations American Power Conference J P Weir, T D Hess American Standards Association , Mining Standards Board E R Borcherdt, Jan '59, Otto Herres, '59, J K Richardson, Dec '58, Alternate E W Bullard

Jan 1, 1958

By J. C. Cordell, C. F. Weinaug

A study of the behavior of retrograde condensation from gas mixtures was made in the presence and absence of sand in order to determine if the condensed liquid would re-vaporize in the Presence of sand. Methane-butane and methane-pentane mixtures that would form liquids by retrograde condensation when produced from a constant volume cell were used. The methane-butane mixtures of similar composition were produced by three different methods. The first two were charged into an empty cell and were produced in one case within a period of 9 hr and in the other within a period of 3 days. The third mixture was charged to a sand-packed cell and produced within a period of 9 hr. The curves relating composition of the produced gas to pressure obtained from these experiments show that equilibrium was maintained as long as liquid was condensing. However, during the portion of the pressure decline where the condensed liquid should be revaporizing, equilibrium was maintained only when the mixture was produced from the sand-packed cell. The methane-pentane mixture is produced only in the presence of sand. The data obtained for this system also show that equilibrium is maintained at all times during the pressure decline. These results indicate that revaporization is aided rather than prevented by the fact that the condensate "wets the sand." The significance to the petroleum industry of the behavior of hydrocarbons in the retrograde region is becoming increasingly important because a large percentage of reservoirs being discovered today arc of the gas-condensate type. The important characteristic of a gas-condensate reservoir is the retrograde condensation of a liquid phase throughout the reservoir if the pressure is allowed to decline. In order to prevent the loss of this retrograde liquid in some of these reservoirs, they are "cycled"; that is, the material produced from the reservoir is processed to remove the heavier hydrocarbons and the light fractions are returned to the reservoir to maintain the reservoir pressure. Another method of producing these reservoirs is Pressure depletion. There are other methods but they are not in general use. Although a large number of factors are involved in determining the optimum method of producing a reservoir, only the problem of whether the retrograde condensate resulting from pressure depletion will revaporize from sand at equilibrium conditions is considered in this paper. Also the data are limited to the methane-n-butane and the methane-n-pentane systerns at loo°F and one type of sand. Three types of tests were run in order to compare the revaporization of retrograde liquid formed in a cell with that formed in a sand-packed cell, and to establish the effect of time. The results of tests presented in this paper indicate that both time and the presence of sand promote the revaporization of

Jan 1, 1949

Meeting; May 23, 1913.-On the petition of 25 or more members residing in the different localities, the following Local Sections were established: St. Louis Local Section. Southern California Local Section; Denver Local Section. It was voted to publish a statement in regard to tours in connection with the Butte meeting, which-is published on p. i of this Bulletin. Mr. Edward Caldwell was appointed as expert advisor. on printing. The report of the Committee on Printing advising certain changes in methods of printing. was accepted.

Jan 6, 1913

By Messervey, J. P.

NOVA SCOTIA is sharing in the rapid advance of the mining industry that is one of the remark- able features of Canada's recent progress. The production of coal and gypsum has increased rapidly, and there has also been a marked development in the mining of gold, salt, zinc, copper and other minerals. Coal, the basis of the principal mining industry in the Province, was discovered by the early explorers on the shore of Cape Breton Island, and used by the garrison at Halifax as early as 1749. The first government record shows total annual sales amounting to 1668 long tons in the year 1785, while last year production was 6,643,000 long tons. The principal mines are discussed in a separate paper by Alexander L. Hay1.

Jan 1, 1928

By J. H. Slater

There is nothing particularly new about the use of sinter in a blast-furnace burden. For many years flue dust has been sintered at the various blast-furnace plants to put it in a form that could be recharged to the furnace with some assurance that it would stay in the second time. This paper is not a compilation of scientific data but only an attempt to give our experience with sinter. There are some unexplained discrepancies in the tests given here, such as the flue dust produced and iron tonnages, but the results given are the results that were obtained. Sinter is not the cure-all for blast-furnace problems. A good coke is still the most important factor in good furnace operation. However, good sinter is a big help. As flue dust is produced under varying operating conditions and fluctuates greatly in carbon content, it is difficult to produce from flue dust alone a uniform sinter, which will give satisfactory blast-furnace results. Sinter made from flue dust alone will change in character with every carbon variation. Almost invariably flue dust contains carbon in excess of the amount necessary to make good sinter, and this excess must be burned out. This, of course, necessitates reduction of the speed of the sintering machine and thus a decrease in tonnage. An alternative is to dilute with a carbon-free material to use up the excess carbon. High-carbon material when sintered results in a very dense, undesirable product, since the excess heat melts the charge into a hard, nonporous mass, and tends to form refractory silicates. At the Republic Steel plant in Cleveland, there had existed since 1924 a continuous-type sintering machine having 224 sq. in. of grate-bar area, capable of producing 9 to 11 tons of sinter per hour from flue dust. Under a former management, it was the practice to sinter only the flue dust from the blast furnaces, no attempt being made to recover the gas-washer sludge. As the dust was limited, the plant operated only part time. In other words, there was a sintering plant representing considerable investment, with good facilities for screening and preparation of raw materials, and flue dust available for only part-time operation. The sinter produced was costly and not a very desirable product. The first step was to install equipment for the recovery of the gas-washer sludge. This was done in the form of two large thickeners and a filter, which have proved very satisfactory. It was then decided to screen out the minus 3/8-in. fines from the Mesabi ores, mix them with flue dust and coke breeze when necessary, and operate the plant at full capacity. The tonnage increased to 18 tons per hour and the product was much improved. Sintering costs fell and the product was a preferred blast-furnace material, which on an iron unit cost compared very favorably with good Mesabi ores. On the average, 40 per cent flue dust and 60 per cent fine ore was being used. The oversize from the ore screening also became a preferred product for the

Jan 1, 1941

By J. H. Slater

There is nothing particularly new about the use of sinter in a blast-furnace burden. For many years flue dust has been sintered at the various blast-furnace plants to put it in a form that could be recharged to the furnace with some assurance that it would stay in the second time. This paper is not a compilation of scientific data but only an attempt to give our experience with sinter. There are some unexplained discrepancies in the tests given here, such as the flue dust produced and iron tonnages, but the results given are the results that were obtained. Sinter is not the cure-all for blast-furnace problems. A good coke is still the most important factor in good furnace operation. However, good sinter is a big help. As flue dust is produced under varying operating conditions and fluctuates greatly in carbon content, it is difficult to produce from flue dust alone a uniform sinter, which will give satisfactory blast-furnace results. Sinter made from flue dust alone will change in character with every carbon variation. Almost invariably flue dust contains carbon in excess of the amount necessary to make good sinter, and this excess must be burned out. This, of course, necessitates reduction of the speed of the sintering machine and thus a decrease in tonnage. An alternative is to dilute with a carbon-free material to use up the excess carbon. High-carbon material when sintered results in a very dense, undesirable product, since the excess heat melts the charge into a hard, nonporous mass, and tends to form refractory silicates. At the Republic Steel plant in Cleveland, there had existed since 1924 a continuous-type sintering machine having 224 sq. in. of grate-bar area, capable of producing 9 to 11 tons of sinter per hour from flue dust. Under a former management, it was the practice to sinter only the flue dust from the blast furnaces, no attempt being made to recover the gas-washer sludge. As the dust was limited, the plant operated only part time. In other words, there was a sintering plant representing considerable investment, with good facilities for screening and preparation of raw materials, and flue dust available for only part-time operation. The sinter produced was costly and not a very desirable product. The first step was to install equipment for the recovery of the gas-washer sludge. This was done in the form of two large thickeners and a filter, which have proved very satisfactory. It was then decided to screen out the minus 3/8-in. fines from the Mesabi ores, mix them with flue dust and coke breeze when necessary, and operate the plant at full capacity. The tonnage increased to 18 tons per hour and the product was much improved. Sintering costs fell and the product was a preferred blast-furnace material, which on an iron unit cost compared very favorably with good Mesabi ores. On the average, 40 per cent flue dust and 60 per cent fine ore was being used. The oversize from the ore screening also became a preferred product for the

Jan 1, 1941

Discussion of the paper of EDGAR L. NEWHOUSE, presented at the Salt Lake meeting, August, 1914, and printed in Bulletin: No. 92, August, 1914, pp. 1801 to. 1806. G. C. RIDDELL, East Helena, Mont.-As nearly as I can recall at the present moment, there are only four or five large plants on the continent where the lead on charge is carried in the neighborhood of 40 per cent. These are at Herculaneum, Collinsville, and Federal, Ill.; Trail, B.. C.; and East Helena, Mont. Our object at the latter point is to smelt a maximum amount of Coeur d'Alêne lead sulphides in as compact and self-fluxing a charge as possible, and to this end we are now smelting a mixture that at times carries up to 42 per cent. lead. The monotony of producing the 7,000 tons of bullion shipped each month to. the Omaha and Chicago refineries is relieved somewhat by the fact that the 15,000 tons monthly of Coeur d'Alêne ores that are com-ing to us carry enough zinc to provide the one-half slag used with from 6.5 to 7.5 per cent. zinc clay after day. During the month of March, 1914, three lead furnaces in continous operation, each 136 in. long, averaged 249 tons per furnace clay, exclusive of coke and slag shells, which is smelting at the rate of 5.5 tons per square foot of tuyère area. The

Jan 11, 1914

TWO very interesting sessions on mine ventilation were held on Monday. George S. Rice, chairman of the Mine Ventilation Committee, presided at the morn-ing session. Formal reports from two subcommittees were presented, as well as two technical papers. Daniel Harrington, for the subcommittee on metal mining, gave a most interesting report, devoting most of it to a review of the literature that had appeared during the past year, to the cooling of mine air, and to a discussion of mine fires. In the absence of Dr. R. R. Sayers, chairman of the Physiological subcommittee, Mr. Harrington gave a resume of that report. The main points covered were in connection with silicosis but some attention was also paid to the associated prob-lems of air cooling and humidity. The paper by Prof. W. S. Weeks on the "Air-Current Regulator" was briefed by Prof. A. C. Callen. Pro-fessor Weeks brought out the fact that the common application of Murgue's equivalent-orifice formula to regulator problems was incorrect, inasmuch as the dis-charge from the regulator was not released into the open air but into a slow-moving current beyond the regulator. He applied the shock-loss theory of Bordoni to the problem and worked out a formula for solving regulator problems, giving coefficients of contraction he had determined experimentally.

Jan 3, 1928

By A. J. Phillips, C. G. Grant, Wm. B. Price

Admiralty nickel is a new corrosion-resisting and heat-resisting white metal alloy composed of 70 per cent. copper, 29 per cent. nickel and 1 per cent. tin. It has been given the trade name "Adnic." In 1924, Wm. B. Price' described this alloy and its successful use as a diaphragm metal. The physical properties of Adnic at ordinary and elevated temperatures were given in Mining & Metallury.~ A patent3 was granted on Adnic, April 28, 1925. Work was first started on this alloy during December, 1921. An investigation of the patent situation in this country and abroad, and also a search of the literature, did not reveal any work on the ternary diagram, copper-nickel-tin; and the only wrought copper-nickel-tin alloy found was that known as "Newloy," composed of copper, 64 per cent.; nickel, 35 per cent.; tin, 1 per cent. This was being manufactured and sold by Wm. Gallimorr & Sons, Ltd., Sheffield, England, for unplated spoon and fork stock, and first came to our attention in January, 1922. The preliminary work in connection with the development of Adnic was started by casting four binary copper-nickel alloys of the compositions shown in Table 1. Various a~ilounts of tin were added to each of these mixtures, to produce the series of ternary copper-nickel-tin alloys also given in Table 1. A 200-gm. sample of each of these was cast by iiielting in a clay graphite crucible and allowing the melt to slowly cool with the furnace. A longitudinal section from each of thcsc castings was polished and etched for examination. The castings were not homogenrous solid solutions, but showed the usual cored structure associated with cast alloys. Howcvrr, frorn an exarrlination of these sections we roughly determined

By R. W. Gurry

WHEN a steel in the austenitic state, with all its carbon in solution, is maintained, at constant temperature, in contact with a gas that removes the carbon from the surface, vet without otherwise altering the composition of the steel, the change in weight of the specimen, after any period of exposure, is a direct measure of the amount of carbon it has then lost. The purpose of the present paper is to show how, by application of established mathematical reasoning based on the fundamental diffusion law and on certain postulates, this loss of weight yields a complete picture of the distribution of carbon throughout a specimen of regular shape after any period of exposure, with all the accuracy required in any practical occurrence of decarburization. Precisely the same is true for the gain in weight during the reverse process of carburization, or for the gradual gain or loss of any element, so long as the steel comprises only a single phase at temperature, provided always that the experimental conditions conform to the postulates. The change in carbon content from surface to center of the specimen is always continuous, when everything is in solution, even though under the microscope the decarburized zone (or carburized rim) may appear to be sharply defined. The experimental procedure is described and some typical results are presented, which are then interpreted by application of the diffusion law. EXPERIMENTAL PROCEDURE Initially an endeavor was made to follow the gain of weight during the process of carburization in a hydrogen-toluene atmosphere, but it was soon found that the specimen became coated with graphite, which could not be removed without some loss of metal; therefore it was decided to continue carburization until the steel was saturated throughout, to remove all graphite from the surface of the specimen, and then to follow the loss of weight during decarburization in a moist hydrogen atmosphere at the same temperature as that used for carburizing. The carburizing procedure has been described in an earlier paper;1 it suffices to state here that the carburization lasted about 140 hr. at 760°C. (1760°F.) and 44 hr. at 1110°C. (2030°F.), these periods being long enough-on the basis of the calculations presented later-to ensure that the specimen was about 9.99 per cent saturated at each temperature. The speci¬men was a cylinder about 3.8 cm. long and 0.475 cm. in diameter; the materials were carbonyl iron, a commercial low-metalloid iron, and a steel with 3.6 per cent nickel and the usual proportion of other elements. The fully [carburized] specimen, after cooling at the top of the furnace tube, was placed in a lathe and sandpapered to remove all graphite; then the diameter was measured with a micrometer caliper, and the initial weighing (corresponding to complete saturation) was made. By means of a

Jan 1, 1942

By David Turnbull

STAFF: Editor, Gerhard Derge Carnegie Institute of Technology Schenley Park Pittsburgh 13, Pa. Editorial Assistant, M. A. Redmerski Production Editor, Otto T. Johnson THE METALLURGICAL SOCIETY: J. S. Smart, Jr., President; C. C. Long, Past-President; K. L. Fetters, Vice President; T. D. Jones, Treasurer; R. W, Shearman, Secretary. PUBLICATIONS COMMITTEE OF THE METALLURGICAL SOCIETY: C. L. McCabe, Chairman; H. L. Bishop, K. L. Fetters, J. J. Harwood, W. A. Krivsky, F. C. Langenberg, R. E. Lund, W. O. Philbrook, L. L. Seigle, R. L. Smith, and F. L. Vogel. Review and selection of monuscripts is under the supervision of the following Publications Committees: Extractive Metallurgy Division: C. L. McCabe, Chairman; R. E. Lund, Vice-Chairman; D. H. Baker, Jr., W. A. Krivsky, R. A. Lewis, Paul Queneau, A. S. Russell, R. E. Shinkoskey, W, W. Stephens, and M. E. Wadsworth. Institute of Metals Division: L. L. Seigle, Chairman, Paul A. Beck, I. I. Bessen, J. 0. Better-ton, Jr., J. B. Clark, R. S. Davis, A. E. Dwight, R. W. Fountain, R. B. Gordon, C. D. Graham, Jr., R. W. Guard, J. C. Gurland, E. L. Harmon, J. J. Heger, A. A. Hendricksan, M. Herman, J. N. Hobstetter, H. H. Johnson, Jr., R. R. Nash, T- N. Rhodin, R. H. Richman, W. Ros-toker, P. G. Shewmon, C. W. Spencer, L.SIifkin, J. K. Stanley, C. D. Starr, and H. C. Stumpf. Iron and Steel Division: H. L. Bishop, Chairman; R. E. Boni, F. C. Langenberg, J. B. Wagstaff, and T. V. Wainwright. Published bimonthly by the American Institute of Mining, Metallurgical, and Petroleum Engineers, Inc., 29 West 39th Street, New York 18, N. Y. Telephone: PEnnsylvania 6-9220. Subscription $20 per year for non-AIME members in United States and North, South, and Central America; $25, foreign; $5 for AIME members. Single copies, $4.00, single copies foreign, $5.00. The AIME is not responsible for any statement made or opinion expressed in its publications . . . Copyright 1961 by the American Institute of Mining, Metallurgical, and Petroleum Engineers, Inc. . . . Registered cable address, AIME New York .. . Indexed in Engineering Index, Industrial Arts Index, and Chemical Abstracts . . . Second class postage paid at New York, N. Y., and Ann Arbor, Mich. Volume 221, Number 3.

Jan 1, 1962

Jan 1, 1928

By J. Hall Carpenter, James E. Lawver

Shortly after the passage of the Taconite Amendment in Minnesota, several mining companies announced their intention to build new magnetite taconite plants and another announced its intention to augment present facilities. It is clear that Minnesota will enjoy an expanding magnetite taconite industry, but despite the fact that the reserves are large, eventually they will have to be supplemented by oxidized deposits. Furthermore, not all producers have magnetite taconite reserves. Due to the extensive oxidation of most of the western part of the Mesabi Range, there are no large blocks of unaltered magnetite taconite that lend themselves to open pit operations. Unless a commercial process can be developed to concentrate the oxidized, or so- called "nonmagnetic", taconite and semi-taconite, the existing mines operating in the western part of the range will be forced to shut down when the direct shipping, wash and gravity ores are depleted, or are no longer salable, because of their poor quality compared to high-grade pellets. KNOWN PROCESSES COSTLY The enormous reserves of the oxidized iron- bearing formation have offered a tantalizing challenge to metallurgists for many years. In fact, several processes for concentrating certain types of oxidized ore have been successful at both laboratory and pilot plant level, but to date no process for concentrating semitaconite or oxidized taconite has reached commercial fruition. Magnetic roasting, followed by low-intensity magnetic separation1, has shown considerable promise because the high iron recovery makes the ratio of concentration of many of the oxidized ores more favorable than that of magnetite taconite. However, the capital and operating costs are high and, in many cases, a high- grade concentrate cannot be made without resorting to flotation of the magnetic concentrate. Hence, most research groups are investigating alternate methods of concentration with the hopes of reducing the cost.

Jan 9, 1965

By W. A. Young

Polynomial functions of temperature were obtained for the specific heats, thermal diffusivities, and thermal conductivities of zirconium hydrides containing 4 at. pct U. Three hydrides (H/Zr atom ratios of 1.58, 1.65, and 1.70) were studied over the range a" to 900°C and a fourth (H/Zr = 1.81) was studied over the range 0° to 760°C. The specific heats were determined from enthalpy measurements which were obtained using a unique drop calorimeter specifically designed for use with materials in which high temperature phase transitions and/or high dissociation pressures occur. Thermal diffusivities were measured by the flash method using a pulsed laser. The thermal conductiuities were obtained as the product of specific heat, thermal diffusivity, and density. The specific heats agree, within 10 pct, with values derived using a theoretical model in which the hydrogen and zirconium atoms are treated as Einstein and Debye oscillators, respectively. RELIABLE values of the thermophysical properties of the fuel are required to predict the operating temperatures and temperature response of SNAP nuclear reactors. Among the most important of these properties are the thermal conductivity, specific heat, and thermal diffusivity. A considerable number of investigations1-4 have been made of these properties for the Zr-H and Zr-H-U systems.* However, little of the drides, however, this direct method cannot yield meaningful results, since the hydrogen will redistribute under the influence of the thermal gradient, thus forming a concentration gradient; hence, one has a spectrum of compositions, rather than a homogenous alloy. Although the "average" composition of the material may be identical to the initial uniform concentration, the directly measured value of conductivity will be dependent on the thickness of the specimen, due to the highly sensitive dependence of transport properties on hydrogen content. This dependence is strikingly illustrated by the work of Bickel,5 who found that the electrical conduction of zirconium hydrides ranges from primarily hole conduction to primarily electronic conduction, depending upon the hydrogen content. Fortunately, the direct measurement of thermal conductivity is unnecessary, since it can be expressed as the product of the specific heat, thermal diffusivity, and density, all of which can be directly measured with considerable accuracy. EXPERIMENTAL Specimen Preparation. The combined fuel-moderator material used in SNAP reactors is a hydrided zirconium-uranium alloy containing -10 wt pct U. The alloy used in this work was representative of that used in nuclear reactors except that normal uranium was substituted for the enriched uranium required for reactor usage. It was produced by a triple-arc-melt and double-extrusion process. All specimens were prepared from a single cylindrical extrusion which contained 10.30 pet U, 89,35 pct Zr, and 0.35 pct impurities, The specimens for each composition were hydrided simultaneously with ultrapure hydrogen (10 ppm total impurities) using standard fuel production techniques which routinely yield homogeneous, crack-free fuel with negligible increases in the impurity levels. The hydrogen content of each specimen was determined from its weight gain and the density was measured by liquid displacement, Chemical analyses yielded hydrogen concentrations which agreed with the weight gain data within ±0.02 in H/Zr atom ratio) the concentrations of all other elements agreed almost exactly with the initial values after adjustment for the added hydrogen. The specimens used for the determination of specific heat were centerless ground to 2.00 cm diam after hydriding. A thin slice was carefully removed From each end for metallographic examination. In every case, this examination revealed a uniform structure as evidenced by the appearance and distribution of the two phases present in the fuel at the hydrogen concentrations used. TWO specimens (H/Zr = 1.600 and 1.632) appeared to be entirely 6 phase with equi-axed grains; the specimen with H/Zr = 1.756 showed

Jan 1, 1970