Search Documents

By George M. Humphrey

It is indeed a pleasure for me to have this opportunity to discuss with you a subject which I find infinitely interesting and intriguing - namely, world-wide iron ore supply and demand. We will be examining the following: (i) current iron ore production and requirements; (ii) the major ore producing countries; (iii) the seaborne iron ore trade; (iv) ore grades or types; and (v) future requirements. For those who may not be familiar with the iron ore mining industry, it may be useful to know at the outset that our industry has been plagued with overcapacity for the past seven years. The optimism which prompted substantial expansion of productive capacity in the early to mid-1970's has unfortunately proved to have been unfounded. I shall begin by describing where we are today as well as a little about how we got there. In the latter regard, it's not so much that historical knowledge will solve any of the industry's problems or provide clairvoyance with regard to the future. Rather it's a feeling on my part that some knowledge of the past will provide a useful perspective capable of enhancing our analysis of future trends. At the time of writing, the most recent year for which we have definitive world-wide iron ore production and consumption statistics is 1980. In that year the world consumed approximately 859 million metric tons of iron ore to produce approximately 510 million metric tons of primary iron consisting of 502 million tons of pig iron and 8 million tons of sponge iron. Crude steel production for the same period attained a level of 719 million metric tons. Because it is possible in today's world to produce steel without consuming iron ore simply by melting scrap, the key statistic insofar as iron ore demand is concerned is primary iron production. In 1980 the ratio of iron ore consumption to primary iron production was 1.68:1.00. The comparable ratio over the past seven years has varied from 1.63 to 1.87 and averaged 1.72:1.00. All the same, as a practical matter crude steel production and iron ore consumption tend to parallel one another closely, and for the time being a good rule of thumb is that to produce an average ton of crude steel requires 1.20 tons of iron ore. Let's turn our attention now to the regions where the 859 million tons of iron ore necessary to support 1980 world-wide iron and steel production were produced. Not surprisingly, most of the ore was produced in the same region where it was smelted. In round numbers 65% of the world's iron ore production is currently consumed in the same general region as it is produced, while 35% enters the seaborne trade and is transported in ocean vessels to a more remote consuming area. Approximately 85% of the world's seaborne iron ore trade is directed to the Western European and Japanese markets, both of which are almost entirely dependent on off-shore sources for their mammoth iron ore requirements. The following tabulation lists, in order, the twelve leading iron ore producing countries in 1980 as well as their percentages of total and free-world production; in addition their export potentials are presented. As a group these countries accounted in that year for 89% of world-wide production which stood at 871 million tons. Leading World Iron Ore Producing Countries [ ] One will first note that world iron ore production is dominated by the top four producers - namely, the U.S.S.R., Brazil, Australia and the U.S.A. - which together accounted for nearly 60% of total 1980 production. Of these four major producers the U.S.A. and the U.S.S.R. produce almost exclusively for consumption in their own regions, whereas Australia and Brazil produce primarily for the seaborne export trade. In fact Australia and Brazil accounted for about 50% of all seaborne iron ore trade in 1980! It is also interesting to note that Australia, Brazil, the U.S.A. and Canada accounted for nearly 60% of free world iron ore production in 1980. Once again the importance of Australia and Brazil shows itself, with their share alone of free world production reaching 35%. As has already been noted, a significant 35% of the world's iron ore production in the year 1980 was

Jan 1, 1982

By J. T. Raleigh, D. L. Flock

This study investigated the nature of formation plugging with bacteria and attempted to relate its characteristics to physical rock properties. Fifteen core samples of four specific formation types were defined and plugged using a commonly occurring, uniform sized dead bacteria, Bacillus subtilis. Two of the formation types were fairly uniform-grained sandstones and two were heterogeneous carbonates. The injection rate and concentration of solids in the brine were held constant during the test runs. The pore geometry factor G was a significant petro-physical rock characteristic for correlation with depth of plugging, but lacked importance as a parameter for rate of plugging. Although the G factor may not completely describe porous rock geometry for plugging predictions, for reservoirs with multi-pore systems, there is evidence that the pore geometry factor might form a basis for establishing injection water specification in more llornogeneous reservoirs with only primary porosity development. INTRODUCTION GENERAL PURPOSE Injecting water into oil-bearing formations to increase recovery is common practice in the petroleum industry. One of the most serious operational problems involved with water injection wells is the tendency of the porous rock immediately adjacent to the injection wellbore to plug partially. This results in increased injection pressures and/or a decrease in the rate of injection. This plugging in injection wells can result from a number of causes, including bacteria contained in the injected water.1 The purpose of this work was to investigate the nature of injection plugging with bacteria and to attempt to relate its characteristics to physical rock properties. Many variables exist in research of this type, so, to reduce them, injection rate and concentration of bacteria in brine were held constant. The bacteria used for plugging was a uniform-sized, dead bacteria, Bacillus subtilis, a micro-organism commonly found in water, air and soils. Four specific porous rock types were plugged—two consolidated sandstones and two heterogeneous carbonates. The experimental work involved two distinct phases. The first concerned determining the physical rock properties and the second was the experimental work of actually plugging the selected core samples. PORE GEOMETRY FACTOR Capillary pressure is necessary to displace a wetting fluid from a capillary opening with a nonwetting fluid. The factors which govern capillary pressure are the surface or interfacial tension of the fluids involved, the system wettability and the equivalent pore radius. Thus: P,= 2ucososrd..........(1) Thomeer used the idea that the location and shape of the capillary pressure curve reflect characteristics of the pore structure of any porous media sample.' He presented the mathematical description of capillary pressure curves and of indicated differences in pore geometry of samples. where G = pore geometry factor PC = capillary pressure Pi = displacement pressure (V,)p, = fractional bulk volume occupied by the displacing fluid at any capillary pressure (V,), = fractional bulk volume occupied by the displacing fluid at infinite pressure or total interconnected pore volumes. The shape of the curve is defined by the pore geometry factor G. The curve shape is related directly to the sorting and interconnection of the pores of the sample. The location of an infinite number of curves can be defined by the same asymptotes. However, these curves differ in shape, each curve being described by a specific value of G. Thus, the description of a curve is unique when, in addition to the position of its asymptotes, its shape is defined. These curves can be used graphically to determine the characteristic parameters of any arbitrarily located curve. Those parameters that can be approximated from any capillary pressure curve are: (1) total interconnected pore volume, represented by (V,),- ; (2) extrapolated displacement pressure, the abscissa axis; and (3) pore geometry factor, by the curve shape. PROPERTIES OF BRINE AND BACTERIA The fluid used throughout this study was an aqueous solution of sodium chloride, 25,000 ppm by weight. The addition of salt to fresh water was intended to eliminate clay swelling in the sandstone cores and to retard leaching in the limestone cores. The viscosity of the brine solution at 100F, the temp-

Jan 1, 1966

By N. W. Wickersham, Ward B. Blodget, Roberts R. Boyd

The year 1926 has seen few radical changes or developments in methods of drilling and handling oil wells, but it has been a year of steady progress and development in deep drilling and production methods. Probably the outstanding development of the year was recognition by the directors of the American Petroleum Institute of the importance of natural gas in the production of oil, and the Institute directors' resolutions in December, 1926, regarding regulation of gas production with oil by state legislation. This matter is extremely important and will receive the attention of the industry in 1927. Advances in Drilling Equipment The history of the progress of deep well drilling is the solution of problems as they have confronted the operator. As the prospects for deeper production have become apparent, methods of penetrating the earth to greater depths have been devised. Rotary Equipment Improvements in the construction and in the methods of operation of rotary drilling equipment have practically caused elimination of cable tools in California for all but shallow work. The rotary drill, from 1910 when it began to be a practical factor in California, has been making steady advances, first displacing cable tools for drilling to the oil sands in proved fields and later displacing the cable-tool outfit entirely. With the perfection of machinery for taking core samples of the formation penetrated, the rotary drill has become generally used for wildcat work, continuous coring being practiced when desirable. Deep Holes The use of the rotary drill has made commercially feasible the opening of oil fields at greater depths than was considered possible with cable tools. Heavier equipment has been promptly supplied as occasion has

Jan 1, 1927

[A AALSETH, EARL P GEOLOGIST. AMERADA PETROLEUM CORP. BOX 1498 BILLINGS. MONT ABADIE, HENRY G ASST TO SUP OF OPER LONG BEACH OIL DEVEL. CO. 255 S. SANTA CLARA. LONG BEACH, CALIF. ABBE. TRUMAN W. … ASST.FLD.SUP.OF PROD SUN OIL COMPANY BOX 66 STOWELL. TEXAS ABBOTT. J. L. .... GEOL. PARTNER PRITCHARD & ABBOTT 504 CENTURY BLDG. FORT WORTH, TEX ABBOTT, RICHARD H OWNER ABBOTT AND HOWARD OIL 422 W. HERMOSA DR. SAN ANTONIO, TEXAS. ABBOTT, SETH J.. JR PETR ENGR.]

Jan 1, 1961

By A. L. Mular. Discussion by G. A. Parks

G. A. Parks (Associate Professor, Dept. of Mineral Engineering, Stanford Univ., Stanford, Calif.) - Professor A. L. Mular in his paper Effect of Impurities on the Flotation Behavior of Zinc Oxide (T.P. 65B206) has made a most interesting and thought provoking contribution. In view of his recognized lack of measurements of the ZPC's of the doped samples and lack of direct evidence for participation of semi-conducting electrons in collector adsorption an alternate explanation should be considered. The alternate also

Jan 1, 1967

By N. P. Goss

Asterism appearing in X-ray Laue diagrams is an extremely sensitive index of changes in the internal structures of individual grains of polycrystalline metals. It indicates the existence of various forms of subboundary structure or subdivision within the grain. The present viewpoint is that the grain is made up of lattice blocks having substantially the same size and shape.l-4 When these blocks all assume exactly the same orientation, the crystal is perfect and asterism is absent. Cleaves and Thompson5 observed that the hardness of iron is virtually constant over a range of grain sizes. It is quite possible that the subboundary structure caused this, and that the latter is just as important as grain size itself. While the experiments reported here are not conclusive, they do support this viewpoint. Metals can, under certain conditions, be prepared entirely free from asterism, but this preparation does not necessarily require long heating or slow cooling, as will be shown here. In this paper a distinction is made between mosaic and distorted grain structures but the difference is only a matter of degree. In a previous paper9 it was shown that the grains can become distorted even during heat-treatment. The block structure exists inherently, even in a perfect crystal; the size and shape of these crystallites, or lattice blocks, varies, depending upon a number of factors. Goetz, for example: has shown that a metal before crystallizing from the molten state must go through a paracrystalline phase with oriented groups of atoms about 10-l4 to 10-l5 c.c., or 10-15 cm. in size. These crystallites, or blocks, appear to survive the most drastic cold-working, for it has been shown, and more elaborately by Wood's recent work," that cold-working cannot reduce the size of these crystallites smaller than of the order 10-5 cm. The interesting correlation brought out by the experiments of Goetz and Wood is that the block size after severe cold-working is of the same order of magnitude as the groups that formed in the metal just before crystallizing from the molten state. The work of Ewald and Rennenger17 and the now classical experiments of Darwin and James12,13 all strongly suggest the existence of a periodic structure of crystal. lites smaller than the grain itself. Related to this effect is the appearance of veinlike markings in the microstructures. Ammer-man and Kornfeld,16 in their experiments, did not observe any evidence of veining in specimens of alpha iron annealed below A3 and believed that veining was not due to impurities in the iron, as Northcott16 suggested; veining was observed by them only in specimens annealed above A3. Hanemann,16 Schrader and Tangerding found that annealing in hydrogen did not diminish veining and so it could not be caused by oxides. They concluded that veining was due to a slight difference in the orientation of ferrite lattice blocks. This viewpoint is well supported by the evidence presented here.

Jan 1, 1941

By N. P. Goss

Asterism appearing in X-ray Laue diagrams is an extremely sensitive index of changes in the internal structures of individual grains of polycrystalline metals. It indicates the existence of various forms of subboundary structure or subdivision within the grain. The present viewpoint is that the grain is made up of lattice blocks having substantially the same size and shape.l-4 When these blocks all assume exactly the same orientation, the crystal is perfect and asterism is absent. Cleaves and Thompson5 observed that the hardness of iron is virtually constant over a range of grain sizes. It is quite possible that the subboundary structure caused this, and that the latter is just as important as grain size itself. While the experiments reported here are not conclusive, they do support this viewpoint. Metals can, under certain conditions, be prepared entirely free from asterism, but this preparation does not necessarily require long heating or slow cooling, as will be shown here. In this paper a distinction is made between mosaic and distorted grain structures but the difference is only a matter of degree. In a previous paper9 it was shown that the grains can become distorted even during heat-treatment. The block structure exists inherently, even in a perfect crystal; the size and shape of these crystallites, or lattice blocks, varies, depending upon a number of factors. Goetz, for example: has shown that a metal before crystallizing from the molten state must go through a paracrystalline phase with oriented groups of atoms about 10-l4 to 10-l5 c.c., or 10-15 cm. in size. These crystallites, or blocks, appear to survive the most drastic cold-working, for it has been shown, and more elaborately by Wood's recent work," that cold-working cannot reduce the size of these crystallites smaller than of the order 10-5 cm. The interesting correlation brought out by the experiments of Goetz and Wood is that the block size after severe cold-working is of the same order of magnitude as the groups that formed in the metal just before crystallizing from the molten state. The work of Ewald and Rennenger17 and the now classical experiments of Darwin and James12,13 all strongly suggest the existence of a periodic structure of crystal. lites smaller than the grain itself. Related to this effect is the appearance of veinlike markings in the microstructures. Ammer-man and Kornfeld,16 in their experiments, did not observe any evidence of veining in specimens of alpha iron annealed below A3 and believed that veining was not due to impurities in the iron, as Northcott16 suggested; veining was observed by them only in specimens annealed above A3. Hanemann,16 Schrader and Tangerding found that annealing in hydrogen did not diminish veining and so it could not be caused by oxides. They concluded that veining was due to a slight difference in the orientation of ferrite lattice blocks. This viewpoint is well supported by the evidence presented here.

Jan 1, 1941

By L. O. Brockway, W. C. Bigelow, J. A. Amy

Specimens of Inconel-X alloy solution-treated at 2050°F and aged for periods of 1, 10, 100, and 1000 hr at 1200°, 1400°, and 1600°F have been examined by electron microscopy and by electron and X-ray diffraction. Four minor phases were identified: titanium nitride, niobium nitride, an M23C6 complex carbide, and the intermetallic ? phase. The two nitrides were found in all of the aged specimens and in the solution-treated alloy, the y' phase formed at all aging temperatures, while the M23C6 carbide formed only on aging at 1200° and 1400°F. Variations in the hardness, rupture strength, creep strength, and yield strength of the alloy have been shown to be related to variation in the size and distribution of the particles of the y' phase within the matrix grains of the alloy, with maximum values of these properties occurring when there is a maximum amount of the phase present and a fine state of dispersion of the particles prevails. THE nickel-chromium alloys containing titanium and aluminum are widely used in applications requiring high strength at elevated temperatures. Studies on relatively simple ternary and quaternary alloys'-4 have indicated that the favorable high-temperature properties of these alloys are related to the precipitation of an intermetallic ?'-phase having a structure based On that of the Ni3A1 phase of the nickel-aluminum system. The present investigation was undertaken to identify the minor phases and to study the microstructural changes occurring in one of the more complex commercial alloys as a result of aging in the service temperature range, with particular emphasis on investigating the role of the ?' -phase. The microstructural changes were studied by electron microscopy and the minor phases were identified by X-ray and electron diffraction. MATERIALS AND METHODS Inconel-X alloy was selected for this investigation because the previous studies of Frey, Freeman, and white6 provided extensive information on the variations in metallurgical properties of this alloy resulting from high-temperature aging treatments. Specimens aged 1, 10, 100, and 1000 hr at 1200°, 1400°, and 1600°F were made available for the present use. These were taken from 1-in. round-bar stock of a commercial heat having the following weight composition: 0.04 C, 0.56 Mn, 6.59 Fe, 0.007 S, 0.38 Si, 0.03 Cu, 73.22 Ni, 14.97 Cr, 0.78 Al, 2.38 Ti, and 1-02 Nb. They were solutjon-treated at 2050 for 4 hr and then water-quenched prior to aging. Powder X-ray diffraction patterns were obtained from insoluble minor phases which were separated from the alloys by digestion in the reagent of Mahla and Nielsen.6 Back-reflection patterns were obtained from electrolytically polished surfaces of the bulk search to detect the ?'-phase' Cu-K a radiation was used in both cases. In the electron-diffraction studies, the general method developed by Heidenreich, Sturkey, and

Jan 1, 1959

By F. Keller

SOME PHRASEMAKER has aptly said that nature made aluminum light but research made it strong. Research has been a vital element in the past progress of the aluminum industry and its future growth likewise depends upon the application of the results of research. The role of aluminum products in World War II is well known and this metal will certainly be increasingly important in the postwar world. Some of the principal developments in the war years were in the field of high-strength aluminum alloys. New and stronger alloys were developed which enabled designers to get increased speed and performance in our fighter planes and bombers. The aircraft industry will continue to use these new materials for peacetime passenger and cargo airplanes. High-strength alloys will also find structural applications in trucks, buses, trains, ships, and bridges.

Jan 1, 1946

By K. Osseo-Asare

LIX63 In combination with DNNS selectively extracts nickel and/or cobalt from acidic leach liquors with pH values as low as 10 Nickel/cobalt and cobalt/nickel selectivities are achieved by varying the relative concentrations of LIX 63 and DNNS Increasing LIX63 concentration retards both extraction and stripping rates while DNNS has the opposite effect. Slope analyses of equilibrium data Indicate that both LIX63 and DNNS are present in the extracted complexes. Examples of possible flowsheets are presented.

Jan 1, 1981

By Theron Wasson

The year 1942 in Michigan was devoted largely to the development of fields discovered in 1941 but was also characterized by a great increase in prospecting for new productive horizons below the Dundee limestone. Some new fields were discovered but as yet these have shown few signs of being of major importance. Michigan's total production for 1942, of 21,754,000 bbl. of oil, as reported by the U. S. Bureau of Mines, was second only to the record year of 1939 when 22,799,000 bbl. of oil were produced. All important fields were prorated throughout the year, and it is obvious that without proration a new all-time high would have been established for the state this year. From 1925 to the end of 1942, Michigan has produced annually the following amounts of oil: Year Barrels Source 1925 4,000 1926 94,000 1927 435,000 1928 592,000 1929 4,641,000 1929 Michigan Geological Survey 1930 3,928,000 3,785,000 1932 6,925,000 1933 7,942,000 1934 0,603,000 1935 15,776,000 U.S. Bur. Mines, 1937 1936 11,928,000 U.S. Bur. Mines, 1938 1937 16,628,000 U.S. Bur. Mines, 1939 1938 19,211,000 U.S. Bur. Mines, 1938 1939 22,799,000 1940 19,764,000 1941 16,361,000 1942 21,754,000 Total 183,170,000 This tabulation shows the steady growth of the industry in Michigan since the first discovery of oil in 1925. Maes A map of the oil and gas fields of Michigan in 1941, published in the report for 1942, shows the main producing areas and should be referred to if information in regard to their location is desired.* The main producing zones were shown in the columnar section in the same publication. Development in Fields Reed City Field.—During 1942 the Reed City field, which ended 1941 with 112 producing oil wells, added 70 new producers to bring the total at the end of the year to 182 wells and 4700 proven acres. A south extension of the field developed during the year was in large part responsible for the increase. Approximately 9,000,000 bbl. of oil was produced from the field during the year, bringing the total accumulated production to the end of the year to roughly 11,750,000 barrels. Headquarters Field.—The Headquarters field, which started the year with ro producing oil wells, ended the year with 41 wells aid 1240 proven acres. Approximately 2,300,000 bbl. of oil was produced in 1942. Kawkawlin Field.—Although not a 1941 discovery, the Kawkawlin field has been actively developed on the 40-acre spacing plan during the last year, 42 producers having been completed, bringing the total number of wells at the end of the year to 77. Nearly 500,000 bbl. of oil was produced during the year.

Jan 1, 1943

By Theron Wasson

The year 1942 in Michigan was devoted largely to the development of fields discovered in 1941 but was also characterized by a great increase in prospecting for new productive horizons below the Dundee limestone. Some new fields were discovered but as yet these have shown few signs of being of major importance. Michigan's total production for 1942, of 21,754,000 bbl. of oil, as reported by the U. S. Bureau of Mines, was second only to the record year of 1939 when 22,799,000 bbl. of oil were produced. All important fields were prorated throughout the year, and it is obvious that without proration a new all-time high would have been established for the state this year. From 1925 to the end of 1942, Michigan has produced annually the following amounts of oil: Year Barrels Source 1925 4,000 1926 94,000 1927 435,000 1928 592,000 1929 4,641,000 1929 Michigan Geological Survey 1930 3,928,000 3,785,000 1932 6,925,000 1933 7,942,000 1934 0,603,000 1935 15,776,000 U.S. Bur. Mines, 1937 1936 11,928,000 U.S. Bur. Mines, 1938 1937 16,628,000 U.S. Bur. Mines, 1939 1938 19,211,000 U.S. Bur. Mines, 1938 1939 22,799,000 1940 19,764,000 1941 16,361,000 1942 21,754,000 Total 183,170,000 This tabulation shows the steady growth of the industry in Michigan since the first discovery of oil in 1925. Maes A map of the oil and gas fields of Michigan in 1941, published in the report for 1942, shows the main producing areas and should be referred to if information in regard to their location is desired.* The main producing zones were shown in the columnar section in the same publication. Development in Fields Reed City Field.—During 1942 the Reed City field, which ended 1941 with 112 producing oil wells, added 70 new producers to bring the total at the end of the year to 182 wells and 4700 proven acres. A south extension of the field developed during the year was in large part responsible for the increase. Approximately 9,000,000 bbl. of oil was produced from the field during the year, bringing the total accumulated production to the end of the year to roughly 11,750,000 barrels. Headquarters Field.—The Headquarters field, which started the year with ro producing oil wells, ended the year with 41 wells aid 1240 proven acres. Approximately 2,300,000 bbl. of oil was produced in 1942. Kawkawlin Field.—Although not a 1941 discovery, the Kawkawlin field has been actively developed on the 40-acre spacing plan during the last year, 42 producers having been completed, bringing the total number of wells at the end of the year to 77. Nearly 500,000 bbl. of oil was produced during the year.

Jan 1, 1943

By G. B. Craig, G. L. Montgomery

A simple technique has been developed which reveals glide dislocations in zone-refined aluminum as etch pits. The technique has been tested quantitatively by making dislocation counts on aluminum single crystals deformed in pure bending. The method has the advantage of being insensitive to the orientation of the surface under examination. A number of etchants which will reveal dislocations in annealed aluminum have been reported.'-' These etchants apparently depend on decoration of the dislocations by an impurity (probably iron) and cannot, therefore, be used to reveal fresh glide dislocations. In addition, it is unlikely that screw dislocations will be etched because of their small attraction for impurity atoms. Amelinckx6 has reported that glide dislocations located along slip traces can be revealed by fluo-rated aqua regia. This work indicated that dislocations themselves, irrespective of decoration by impurity atoms, are responsible for the etch pits. However, as a result of additional etching experiments, Wyon and Marchin7 concluded that dislocations alone are not sufficient to explain the localization of etch pits on slip lines in aluminum using chemical etch-pitting techniques. In addition, their results show that glide dislocations are revealed only on surfaces approximately parallel to a (100) axis and that not all slip systems are attacked. These observations have been confirmed by the present authors. The technique described in this article is insensitive to the orientation of the surface, and reveals dislocations on all glide systems. Fig. 1 shows a deformed region in the neighborhood of a scratch. Dislocations can be seen along three slip traces. In the present work, single crystals of zone-refined aluminum are polished for from 2 to 5 min in a chemical polishing reagent held at 100°C, as described by Herenguel and second:' H2Sol 60 pct H3PO4 30 pct HNO3 10 pet The samples are then coated with a thin oxide film by annealing in air at 450°C for 1 hr and cooling in the furnace. After deformation, dislocation etch pits are developed by immersing the specimen in the same polishing solution which is now held at a temperature of 50°C. The formation of small hydrogen bubbles indicates that etching has occurred. The sample is immediately removed from the solution. Prolonged etching results in enlargement of the pits and, in regions of high dislocation density, the overlapping and loss of resolution of individual pits. It is the experience of the authors that contact with iron will ruinously contaminate the reagent. With careful etching, dislocations separated by half a micron can be resolved optically and the method has been shown to be sufficiently sensitive to reveal dislocations produced during the pre-easy glide region of deformation, Fig. 2. A few examples of glide-dislocation configurations, as revealed by this technique, are shown in Figs. 1 to 4.

Jan 1, 1964

By Alexander R. Troiano, Eugene P. Klier

Since the very early work on quenched structures, where the products of the martensite transformation had been recognizedl this transformation has provoked much interest and study. Theoretically it was desirable to account for the extreme changes in physical properties resulting from the formation of martensite, as that information might lead to results of practical importance. Desirable information, therefore, was on the kinetics of transformation from austenite to martensite as well as on the physical constitution of the martensite. It has been known for years that certain steels quenched to room temperature will contain persistent austenite as well as martensite. Other important and now well-established features of the martensite reaction are the Progress of the reaction on cooling only and the independence of Ar" with cooling velocities exceeding the critical velocity. These facts have been experimentally determined by various methods and investigators. Notable among the early investigators were Tammann and Scheill and Wever and Engel.2 Unfor- tunately, all investigators did not fully interpret their results, which, coupled with several investigations that yielde. conflicting resultsl caused a state of confusion that was not clarified until quite recently. X-ray investigations of martensite in steels3-6 indicate it to be a supersaturated solid solution of carbon in alpha iron. This supersaturation is evident from the appearance of a body-centered tetragonal structure with the addition of sufficient carbon. The dimensions of this tetragonal structure are a linear function of the carbon content within the limits of accuracy of the determinations. Slight tempering of tetragonal martensite leads to the destructi,, of the tetragonal structure, which is converted to a body-centered cubic strutture. This phenomenon has precipitated a controversy concerning the nature and mechanism of the tempering of martensite The facts in the case have been outlined by Epstein7 and more recently by Antia, Fletcher, and Cohen.8 The significance of Ar" on theoretical grounds is not clear, however, although considerable study has been devoted to its determination. The precise position of Art' aS a function of carbon content was first stated by Greninger and Troiano9 for steels covering a range of approximately 0.7 to 1.8 per cent carbon. The effect of alloying elements on Ar" has recently been the subject matter of investigation by various methods.

Jan 1, 1945

By P. W. Barton, A. A. Johnson, E. J. Hughes

THE only systematic work on the effect of carbon on the recovery and recrystallization kinetics of iron so far reported in the literature is that of Venturello et al.1 These workers found that doping high-purity iron so that it contained up to 86 ppm C caused a marked retardation of recovery but had little or no effect on the recrystallization kinetics. Such evidence for an effect as was obtained was inconclusive. In the course of a study of electron-beam zone-refined iron the authors have recently examined the effect of added carbon on the recrystallization kinetics of this material. The amount of carbon added was about 50 pct more than was used by Venturello et 01. and definite evidence was obtained that carbon at this level retards recrystallization. The starting material was taken from a batch of 0.2-in.-diameter Johnson-Matthey spectroscopically pure iron rods which had been further purified by being given three passes at 4 in. hr-1 in a standard MRC electron-beam zone-refining unit. The purity of this material. which was used in two other investigations of the properties of high-purity iron,2,3 was established by an extensive series of analyses. Four laboratories, the National Research Corp., Newton, Mass., the Naval Research Laboratory, Washington, D.C.. the Battelle Memorial Institute, Columbus, Ohio, and the National Physical Laboratory. Teddington. Middlesex, England. carried out analyses for carbon. oxygen. and nitrogen. and in addition a complete mass-spectrograph analysis was carried out at Battelle. In all, twelve analyses were carried out for carbon, seventeen for oxygen and twelve for nitrogen. The amounts of these elements found to be present were 10 * 7, 8 i 5, and 0.9 i 0.1 ppm, respectively. The limits given are rms deviations. Two results, one of 46 ppm of oxygen and another of 31 ppm of nitrogen, were rejected as anomalous. The mass-spectrograph analysis revealed the major impurity to be 25 ppm of tungsten. All of the other elements detected were present in amounts less than 0.5 ppm. Some of the rods were doped with carbon by being immersed in a suspension of carbon in oil, heated in a vacuum at 400°C, and then zone-leveled to make the distribution of carbon uniform. Carbon analyses carried out on three of the doped rods gave a mean value of 130 ± 45 ppm. Some of the doped and undoped rods were deformed 58 pct by swaging and cut into specimens 1/2 in. in length. Isothermal recrystallization experiments were then carried out on them at 575", 600°, 615", 630°, and 650°C, the volume fraction of each specimen recrystallized being measured by a point-counting method described by Hilliard and Cahn.4 The results for the two types of specimens are shown separately in Figs. 1 and 2. In Fig. 3 the pairs of recrystallization curves for each temper-

Jan 1, 1965

By F. S. McNicholas

IN the writer's opinion the term "block caving" has been rather loosely applied to a general principle of mining, and therefore detailed classification of caving methods and draw, together with the characteristics required for each method, will fill a desired need. Selection of caving method should be made only after a study of all governing conditions, such as size of orebody, lateral and vertical extent of ore-body, attitude, treatment demands, possible resultant pressures, and cost and profit comparison of methods. Successful caving methods can be classified under six main headings: (1) Full-protected block caving, (2) semi-protected block caving, (3) unprotected block caving, (4) full-panel caving, (5) half block-panel caving, (6) block-panel caving. The methods and factors governing choice of method are shown in Table I. Full-protected Block Caving Full-protected block caving consists of develop-ing, undercutting, and drawing to exhaustion a block of ore of predetermined size without coordination of mining or draw with adjoining areas. The block is mined and drawn as an independent unit (Fig. 1). Full-protected block caving demands that mining and draw cannot be done against unconsolidated capping in adjoining caved and exhausted blocks. Two sides of block are against solid. Caved capping must be allowed to consolidate for a suitable period, usually not less than one year. Pillars may be left in lieu of consolidated capping (Fig. 2). The advantages of full-protected block, caving are: (1) A definite area is developed, mined, and drawn as a unit so that all work may be completed, the block drawn to exhaustion in the minimum length of time, and the area then abandoned. (? Production is not restrained because of coordina1, on with adjoining areas. (3) Records of draw and caved reserve of ore are good. Upon abanwnment of the block, accountability for production is closed out with no carry-over to adjoining areas. The disadvantages of full-protected block caving are: (1) Side dilution from the draw adjacent to the consolidated capping may be serious, particularly where capping does not consolidate sufficiently in the allotted time. (2) Boundary weakening is needed on the solid sides of the block except in weak rocks. (3) Maximum cantilever and compression effect to aid caving and fragmentation may not be secured since the draw should proceed from the solid to the consolidated capping to minimize side dilution. However, undercutting from the loose (caved capping) to the solid with a slight initial draw in the same manner will develop cantilever effect. (4) A period of at least one year, more is usually desirable, must be allowed for caved capping ,to consolidate before mining the adjoining block, depending upon the characteristics of the capping. (5) Capping may not consolidate sufficiently in the time that can be allowed. Full-protected block caving is indicated where: (1) The ground is weak and heavy and workings

Jan 1, 1952

SEC. 1. The membership of the Institute shall comprise six classes, namely: 1. Members; 2. Honorary Members; 3. Senior Members; 4. Associates; 5. Junior Members; 6, Rocky Mountain Members. All shall be equally entitled to the privileges of membership, excepting that no member of any class whose residence shall be outside of the United States of America, except those residing in Mexico and Canada, shall be entitled to vote. SEC. 2. Members: A person to be eligible for election or transfer into the class of Member must be at least 27 years of age and must have had at least six years' employment in the practice of engineering, mining, geology, metallurgy, or chemistry, during at least three years of which he must have held positions of responsibility in one or more of these fields. This shall not apply to Rocky Mountain members. SEC. 3. Honorary Members: Each candidate for Honorary Membership must be recommended by at least ten Members and must be elected by ballot at a meeting of the Board of Directors by the unanimous vote of the Directors present; provided, however, that the number of Honorary Members shall at no time exceed twenty. Such election shall automatically act as a transfer of such member from any other class of membership to which he may belong. SEC. 4. Senior Members: The Directors may in their discretion place on the Honor Roll of Senior Members and transfer from any other class of membership other than Honorary Membership the name of any Member or Associate who has reached the age of seventy years and who has paid dues for thirty years, and for good reasons in • special cases may vary the age or number of years. SEC. 5. Junior Members: A person to be eligible for election to the class of Junior Member must be qualified through education or experience to hold a subordinate position in engineering, mining, metallurgical, geological or chemical work. He shall be not more than twenty-seven years of age at the time of election. The rights of the present Junior Associates shall continue until the same expire by limitation of time. SEC. 6. Associates: A person eligible for election or transfer into the class of Associate shall be one, who, in the opinion of the Committee on Admissions and the Board of Directors, is suitable for such election or transfer by reason of his interest in or connection with mining, geology, metallurgy, or chemistry. SEC. 7. Rocky Mountain Members: Membership in a special class of life memberships without annual or other dues and without right to receive the printed literature distributed to other members or the right and privilege of wearing the official badge of technical members, is given to all members of the Rocky Mountain Club at the time of consolidation. These special Rocky Mountain memberships shall be claimable by any member of the Rocky Mountain Club, not already a member of the Institute,

Jan 1, 1929

By T. W. Smoot

Bentonites are composed chiefly of montmorillonites which are clay minerals generally distinguished from other clay minerals by their surface activity and extremely fine particle sizes. The uses of bentonite are many and varied, depending principally on one or more of the following characteristics: 1) Thixotropy, 2) Dispersion, 3) Plasticity, 4) Swelling, 5) Surface area, activity, ab- and adsorbtive properties. Some of the major uses of bentonite are briefly reviewed as are the mineralogical and physical properties. The uses of X-ray diffraction, differential thermal analysis and other tests for physical properties are reviewed as to their uses in evaluation. In the past 40 years, the industrial uses of bentonite have grown to include many applications. The physical and chemical properties of bentonites are such that they can be used as catalysts, adsorbants, plasticizers, binders, drilling muds, and pelletizers. Not all bentonites, however, can be used for all of these purposes and some are probably of little or no value for any use. The purpose of this paper is to briefly review the mineralogical, physical, and chemical characteristics and variations of bentonites. The determination of these characteristics and their uses in industry are also reviewed so that these determinations can be used as guides for evaluation. DEFINITION OF BENTONITE The word bentonite, as used in this paper, refers to a clay material, usually (but not necessarily) the result of the in-place-weathering of volcanic ash. Its mineralogical composition is dominated by the clay mineral montmorillonite and generally carries other clay minerals and silica minerals as the major 'impurities'. For this discussion, such a definition is justified since most of the economic uses of bentonite~ depend upon the physical and chemical characteristics of the montmorillonite minerals involved. The terms montmorillonite and bentonite have been used almost interchangeably in industry although the latter is much more commonly used. Therefore, where montmorillonite is discussed, it should be understood that the major feature of a bentonite is the subject. STRUCTIJRE OF MONTMORILLONlTE The economic importance of bentonites is generally based on one or more of the following characteristics of montmorillonite: 1) high-thixotropy and easy dispersion in water, 2) high-plasticity, 3) swelling properties, 4) large surface area/unit mass, 5) high surface activity, and 6) adsorptive properties. To understand these properties, an appreciation of the structural scheme of montmorillonite is helpful. Montmorillonite IS one of the three-layer clay minerals composed essentially of hydrous aluminum silicates. The essential building blocks of these layered silicate:; are: 1) silica tetrahedron composed of a silicon atom surrounded by four oxygen atoms, and 2) aluminun (iron, magnesium, etc.) octahedral unit that, ideally, has one of these atoms surrounded by six hydroxal units. Fig. 1 is a diagrammatic sketch of the montmorillonite structure. In the montmorillonite structure, the tetrahedron are pointed inward and attached to the octahedral units so that the O= atoms replace the hydroxal units where they are bonded; hence two-thirds of the hydroxal units

Jan 1, 1962

By J. W. Downey, M. V. Nevitt

MUELLER and Knott' have reported that Ti2Cu has the Si2Mo-type (Cllb) structure. The lattice parameters of Ti2Cu and the positions of the titanium and copper atoms are given by them as follows: ao = 2.944A; co = 10.786A 6 atoms per unit cell: 2 Cu (a) 000; 1/2: 1/2, 1/2 4 Ti (e) 002; 1/2, 1/2, 1/2 + z 00 -2 ; 1/2. 1/2. 1/2- z where z = 0.341 We have found eight other binary compounds which appear to be isostructural with Ti2Cu. All of them involve the combination of a titanium group element with a copper group element or a titanium group element with palladium. The compounds and their lattice parameters are given in Table I. The alloy samples were prepared by arc melting metals having a purity of 99.9 pct or better. They were homogenized for 72 hr at 900°C in evacuated capsules and quenched in tap water. Filings were prepared, and these were reannealed for 4 hr at 700°C, also in evacuated tubes. The lattice parameters were determined by a least squares Bnalysis of the back reflection lines of patterns made with cobalt radiation. It was not possible to make a precise determination of the lattice parameters of Zr2Au because the filings underwent rapid oxidation at room temperature. The evidence supporting the large tetragonal cell containing 6 atoms involves the presence of the reflections 002, 101, 004, 112, 114, 202, and other reflections with higher indices for which I = 3n. Three or more reflections corresponding to these indices, which cannot be indexed on the basis of a small body-centered tetragonal cell containing 2 atoms, are observed in the patterns of all of the compounds listed in Table I. They are strongest and most numerous when the components have large differences in their atomic scattering factors, as is the case in Ti2Pd, Zr2Cu, and Hf2Cu. The values of the z parameter should be regarded as approximate They were selected on the basis of the best agreement between the observed intensities of two pairs of closely spaced powder pattern lines (004): (112) and (114): (202) and the corresponding intensities calculated for several values of z. An ordering scheme was assumed in which titanium, zirconium, or hafnium atoms occupy the titanium positions of Ti2Cu, and copper, silver, palladium, or gold atoms occupy the copper positions. Calculated and observed intensities of the aforementioned lines and the other lines of the patterns are in satisfactory agreement, but a refinement of the z parameters and a final confirmation of the ordering arrangement must await a more detailed study. It is interesting to note that in transition metal systems at A2B stoichiometry the Si2Mo-type structure competes for stability with two other fre-

Jan 1, 1962

By Leo J. Miller

It is both an honor and a pleasure for me to be the keynote speaker for the Paul F. Kerr's Symposium on Applied Mineralogy. Professor Kerr was a man for all seasons to his students, and he treated all students as distinct individuals. Philip Bethke in his memorial to Dr. Kerr summed up our remembrance best by stating that "We have lost our most successful educator-administrator-scholar, who was our steadfast teacher-counselor-mentor-friend." His unique trait was the ability to bring out the best in a variety of individuals In order that their performance was at the peak of quality.

Jan 1, 1985