Search Documents

By E. W. Davis

About a year ago several carloads of magnetite ore from New York state were sent to the Mines Experiment Station at the University of Minnesota for grinding and concentration tests. The flowsheet used minus ½-in. ore as feed to a 3 by 3-ft. overflow cylindrical ball mill operating at 37 r.p.m. in closed ciruit with a vibrating screen. The screen oversize was returned to the mill for further grinding and the screen undersize was concentrated magnetically. Several different screens, between 8 and 35 mesh, were used and it was desired to determine the capacity of the ball mill operating in closed circuit with each screen. From earlier tests using this flowsheet and equipment, it was known that when comparatively coarse screens were used it was necessary to increase the grinding dilution in the mill beyond that ordinarily used when grinding in closed circuit with classifiers. It was also known that after the circulating load had passed about 100 per cent of the original feed it tended to increase rapidly in amount, and grinding conditions appeared to become unstable. These conditions may be peculiar to this small ball mill but they were very marked in this series of tests. If conditions were not right, the mill would suddenly "go dead," and it was found desirable to operate so that the occasional rattle of balls against the lining of the mill could be detected. As the test proceeded, it was found that the cure for almost any difficulty that developed in the grinding circuit was to add more water to the mill feed. To begin with, the mill was operated at pulp densities of from 60 to 65 per cent solids but gradually it was found that with higher dilutions grinding conditions were more stable and the ball-mill power per ton of screen undersize decreased. Actually, the most satisfactory operating conditions were secured with a pulp density of about 40 per cent solids. The ore was hard but it was possible to grind ½-in. feed so that all would pass an 8-mesh screen with a power expenditure in the ball mill of less than 2½ kw-hr. per ton and with a circulating load of less than 50 per cent. With so high a dilution in the feed to the mill, it was feared that steel wear would be very high. However, the mill was not noisy, and in order to find exactly the grinding conditions, a special test was made at the end of the main series of tests. After the mill had been in operation for several hours and grinding conditions had become balanced, the power to all the equipment was shut off at a given signal. The ball mill made about one revolution after the power was turned off, and just as soon as the mill stopped, a spout was placed at the discharge trunnion and all of the pulp that flowed out of the mill was caught in tanks. The manhole in the mill was then opened and the whole mill charge dumped into other tanks. Both of these products were weighed, dried, and weighed again. The balls were screened out and weighed, and the dry solids were sized. In this way it was possible to determine the nature of the pulp and the ore within the mill under actual grinding conditions.

Jan 1, 1947

By E. W. Davis

About a year ago several carloads of magnetite ore from New York state were sent to the Mines Experiment Station at the University of Minnesota for grinding and concentration tests. The flowsheet used minus ½-in. ore as feed to a 3 by 3-ft. overflow cylindrical ball mill operating at 37 r.p.m. in closed ciruit with a vibrating screen. The screen oversize was returned to the mill for further grinding and the screen undersize was concentrated magnetically. Several different screens, between 8 and 35 mesh, were used and it was desired to determine the capacity of the ball mill operating in closed circuit with each screen. From earlier tests using this flowsheet and equipment, it was known that when comparatively coarse screens were used it was necessary to increase the grinding dilution in the mill beyond that ordinarily used when grinding in closed circuit with classifiers. It was also known that after the circulating load had passed about 100 per cent of the original feed it tended to increase rapidly in amount, and grinding conditions appeared to become unstable. These conditions may be peculiar to this small ball mill but they were very marked in this series of tests. If conditions were not right, the mill would suddenly "go dead," and it was found desirable to operate so that the occasional rattle of balls against the lining of the mill could be detected. As the test proceeded, it was found that the cure for almost any difficulty that developed in the grinding circuit was to add more water to the mill feed. To begin with, the mill was operated at pulp densities of from 60 to 65 per cent solids but gradually it was found that with higher dilutions grinding conditions were more stable and the ball-mill power per ton of screen undersize decreased. Actually, the most satisfactory operating conditions were secured with a pulp density of about 40 per cent solids. The ore was hard but it was possible to grind ½-in. feed so that all would pass an 8-mesh screen with a power expenditure in the ball mill of less than 2½ kw-hr. per ton and with a circulating load of less than 50 per cent. With so high a dilution in the feed to the mill, it was feared that steel wear would be very high. However, the mill was not noisy, and in order to find exactly the grinding conditions, a special test was made at the end of the main series of tests. After the mill had been in operation for several hours and grinding conditions had become balanced, the power to all the equipment was shut off at a given signal. The ball mill made about one revolution after the power was turned off, and just as soon as the mill stopped, a spout was placed at the discharge trunnion and all of the pulp that flowed out of the mill was caught in tanks. The manhole in the mill was then opened and the whole mill charge dumped into other tanks. Both of these products were weighed, dried, and weighed again. The balls were screened out and weighed, and the dry solids were sized. In this way it was possible to determine the nature of the pulp and the ore within the mill under actual grinding conditions.

Jan 1, 1947

By P. S. Roller

P. S. ROLLER,*College Park, Md.-The author introduces the idea of a grind limit, or lower size limit of the particles formed directly by grinding, and this is stipulated to be 0.70 micron. I wonder where all the particles come from that lie between the resolving power of the microscope and 0.7 micron, which are seen under a microscope in examining a sample of grind? There is also introduced the idea of excess fines; this is all right in itself but the author's quantitative definition seems to be virtually impossible to justify, and, moreover, is obscure. Just why E, the excess fines, should he defined as the distance between an F line and a y line is hard to follow, and just where the distance should be measured does not appear to be stated, as it should be since the F and y lines intersect and the distance between will depend upon where that distance is measured. The basis of the presentation is the relation of log weight against log size that was "discovered" by Schuhmann. While this relation is implied to fit, the only evidence that I can see is a slightly irregular line in Fig. x between 2 per cent and 18 per cent by weight and then a precipitous drop at 18 per cent away from any sort of straight line. Some of the conclusions are rather startling. It is stated that E, the excess fines, remains constant for all the comminution products of any particular material, except that it may decrease for some coarse crusher products. No reason is given for this assertion. One would, on the contrary, expect that excess fines, if such a concept is permissible, would generally vary with different conditions instead of being constant. Again, "as much net energy is required to reduce a ton of quartz to particles of the grind-limit diameter (namely, of course, 0.7 micron) by grinding as is required to melt the quartz." This would require many data to prove, but no proof is given; any consideration would reveal the impossibility of such a result. Still further, ore samples "ground to widely different sizes, and with different circulating loads and different size distributions or product, show the same production of new surface area per revolution of the mill, when this grind limit is used." This statement is confuted by ordinary experience, which teaches that grinding efficiency varies generally with the condition of material. For example, the cushioning effect of fines is widely accepted, while the inefficiency of a ball mill when the feed is too coarse is also well known. R. SCHUHMANN, JR.," Cambridge, Mass. Contrary to Mr. Bond's stand, there is a great deal of miscellaneous experimental evidence that comminution does not stop at around 0.7 micron, nor does it cease consuming energy at that point. Comminution is in fact recognized as an important method of producing colloids., Mechanical comminution methods were used by von Weimarn6 to produce colloidal dispersions of a variety of solids, including the minerals chalcocite, galena, hematite, stibnite. Utzino7 gives average particle sizes ranging from 0.02 to 0.09 micron for colloids produced by mechanical comminution of several crystalline solids. Andreasen and Berg' have ground

Jan 1, 1941

By E. W. Davis

ABOUT a year ago several carloads of magnetite ore from New York state were sent to the Mines Experiment Station at the University of Minnesota for grinding and concentration tests. The flowsheet used minus ½ -in. ore as feed to a 3 by 3-ft. overflow cylindrical ball mill operating at 37 r.p.m. in closed ciruit with a vibrating screen. The screen oversize was returned to the mill for further grinding and the screen undersize was concentrated magnetically. Several different screens, between 8 and 35 mesh, were used and it was desired to determine the capacity of the ball mill operating in closed circuit with each screen. From earlier tests using this flowsheet and equipment, it was known that when comparatively coarse screens were used it was necessary to increase the grinding dilution in the mill beyond that ordinarily used when grinding in closed circuit with classifiers. It was also known that after the circulating load had passed about zoo per cent of the original feed it tended to increase rapidly in amount, and grinding conditions appeared to become unstable. These conditions may be peculiar to this small ball mill but they were very marked in this series of tests. If conditions were not right, the mill would suddenly "go dead," and it was found desirable to operate so that the occasional rattle of balls against the lining of the mill could be detected. As the test proceeded, it was found that the cure for almost any difficulty that developed in the grinding circuit was to add more water to the mill feed. To begin with, the mill was operated at pulp densities of from 60 to 65 per cent solids but gradually it was found that with higher dilutions grinding conditions were more stable and the ball-mill power per ton of screen undersize decreased. Actually, the most satisfactory operating conditions were secured with a pulp density of about 40 per cent solids. The ore was hard but it was possible to grind ½ in. feed so that all would pass an 8-mesh screen with a power expenditure in the ball mill of less than 2 1/2 kw-hr. per ton and with a circulating load of less than 50 per cent. With so high a dilution in the feed to the mill, it was feared that steel wear would be very high. However, the mill was not noisy, and in order to find exactly the grinding conditions, a special test was made at the end of the main series of tests. After the mill had been in operation for several hours and grinding conditions had become balanced, the power to all the equipment was shut off at a given signal. The ball mill made about one revolution after the power was turned off, and just as soon as the mill stopped, a spout was placed at the discharge trunnion and all of the pulp that flowed out of the mill was caught in tanks. The manhole in the mill was then opened and the whole mill charge dumped into other tanks. Both of these products were weighed, dried, and weighed again. The balls were screened out and weighed, and the dry solids were sized. In this way it was possible to determine the nature of the pulp and the ore within the mill under actual grinding conditions.

Jan 1, 1945

By J. Wayne Erickson

One of the major problems facing today's mining industry is how to manage people and control costs in the underground mine. It is a problem with a solution. Because of the concerted effort to find and mine minerals near the surface, open-pit mine opportunities for certain minerals are becoming more limited; the mining industry will eventually be forced to produce more and more from underground mines in order to obtain those resources necessary to sustain our civilization. Although much technical progress has been made towards solving problems associated with the underground mine, such as - mine design, ventilation, rock support, equipment, and blasting techniques, little has been written on managing mining personnel. Much of what is being taught and practiced today about human relations, motivation, incentives, etc., applies to the underground miner, but the uniqueness of his group dictates a different treatment from that associated with the typical construction worker or factory employee. The difference lies with the kind of man attracted to underground mining and his working environment. Anyone who has had the responsibility of managing an underground mine would agree it is a unique problem.

Jan 9, 1976

By W. S. Landis

WHEN dealing with a new reagent, one is concerned with three principal factors: available supply, cost, and results. The atmosphere contains an inexhaustible supply of oxygen mechanically mixed with nitrogen (omitting rare gases and minor impurities) in the proportions of one volume of oxygen to four volumes of nitrogen. (All figures are based on slide-rule precision and minor impurities are neglected.) Expressed in terms of weight, 1 ton of oxygen represents a volume of 22,500 cu. ft. and is contained in a volume of 112,000 cu. ft. of air. Water, also an inexhaustible supply, is a chemical compound containing 89 per cent. oxygen and, 11 per cent. hydrogen. Of the hundreds of schemes proposed for the enriching of air or separation of oxygen, nothing of value has yet appeared. From the standpoint of mechanical separation, liquefaction followed by rectification is the only process that has been developed to a really commercial stage. Theoretically, it should be a .simple matter to separate the mechanical mixture of nitrogen and oxygen; but fractionation can be performed only by converting to the liquid phase and this phase can be obtained only at lower than critical temperatures. The problem, therefore, is not so simple and the cost of the actual operation bears no relationship to the theoretical simplicity of the process. The largest single unit of the required apparatus so far placed in commercial use will handle only 60,000 cu. ft. of air per hour through a compressor which operates at a little over 250 lb. per sq. in. After this apparatus has operated continuously for 14 to 18 days it must be shut down for 6 to 8 hr. to be thawed out, have accumulated impurities removed and again cooled down for production. The cost of such a unit erected in batteries, with necessary spares for maintaining production, and including prime movers, hoisting and all auxiliary equipment, will be about $125,000. To produce one ton of oxygen per hour requires two operating machines of this size; and if the production is to be absolutely continuous a spare unit must be provided. To operate a plant of two units requires 10 or 11 men, excluding boiler attendants, if steam is generated in the plant.

Jan 11, 1924

By Joseph C. Kieffer

THE Duquesne property of the Callahan Zinc-Lead Co. is about 20 miles east of Nogales, in southern Arizona. One mine is near the mill, but most of the mill feed is hauled in by truck from a number of small mines. The same sulphides are found in all the ores, in general, but the amounts vary considerably. All ores contain silver, copper, lead and zinc minerals but one mine ships ore high in silver and lead and low in copper and zinc; while another mine ships ore high in copper and zinc, and low in silver and lead. The common sulphides are galena, carrying most of the silver; chalcopyrite; sphalerite, carrying iron in solid solution; and pyrite, in a gangue consisting of limestone, quartz and garnet. Mineralization is fairly coarse. At the present grind of about 66 per cent minus 200 mesh most of the sulphides are liberated. A small amount of chalcopyrite is locked up with the sphalerite and cannot be liberated at an economic grind, and the copper carried into the zinc concentrate with the sphalerite accounts for the comparatively poor recovery of copper in the copper-lead concentrate. PRODUCTION OF TWO CONCENTRATES The milling problem, which was complicated by the extreme variation in the grade of the feed, was first attacked with the idea of producing a silver-copper-lead concentrate and a zinc concentrate, both with satisfactory grades and recoveries. By February I94I, it was felt that these objectives had been attained, when the grades of the various products and the recoveries were as shown in Table I. [ ] A rough outline of the flowsheet and reagents used is as follows: Minus ¾ -in. feed to a 7-ft. by 36-in. Hardinge ball mill working in closed circuit with a 36-in. Wemco classifier. The classifier overflow passes to the second cell of an 8-cell bank of No. 18 Special Denver Sub-A flotation machines (volume, 22.5 cu. ft. per cell). A rougher concentrate is removed from the second to the fifth cells inclusive, and returned to the first cell, which is the cleaner. A scavenger concentrate is removed from the sixth, seventh, and eighth cells, and returned to the third cell. Consump

Jan 1, 1942

By L. A. Roe, E. A. Elevatorski

Wollastonite, named after William H. Wollaston, an English chemist, is a calcium metasilicate, CaSiO3; CaO: 48.30%, SiO2: 51.70%. It has a short history as an industrial mineral. The earliest production of wollastonite is reported to be from a deposit near Code Siding, located north of Randsburg, CA. At this locality small tonnages of wollastonite were quarried during 1933-34 and 1938-41, and processed into mineral wool. This operation was largely experimental and virtually no United States production was again reported until the 1950s when a large deposit near Willsboro, NY, was developed by the Cabot Corp. A processing plant was placed onstream in 1953, with nearly continuous production to date. It is currently operated by NYCO, a division of Processed Minerals, Inc. Since 1958, wollastonite deposits in the Little and Big Maria Mountains of Riverside County, and in the Panamint Range of Inyo County, both in California, have operated intermittently for production of both ornamental and commercial wollastonite. During 1980, the United States was the major producing country, furnishing about 75% of the world's output. Current production comes from Finland, Mexico, India, and Kenya. Small amounts have been shipped intermittently from the USSR, New Zealand, Republic of the Sudan, Republic of South Africa, and Namibia (South-West Africa). The principal use of wollastonite is in the manufacture of plastics. Other uses are for paints, ceramics, adhesives, fluxes, glazes, thermal insulation board, and refractory products. Mineralogy Pure wollastonite, CaSiO3, has the composition of 48.3% CaO and 51.7% SiO2. However, it is seldom found in the pure state due to the ease with which it takes into solution the metasilicates of manganese, magnesium, iron, and strontium. Predominantly, wollastonite occurs as a contact metamorphic deposit forming between limestones and igneous rocks. Commonly associated minerals are garnet, diopside, epidote, calcite, and quartz. It has a specific gravity of 2.8 to 3.0, and hardness of 4.5 to 5 on Mohs' scale. When pure, it has a brilliant white color, but with impurities it may be grayish or brownish. Luster is vitreous to pearly. Melting point of wollastonite is about 1540ºC. Wollastonite occurs in coarse-bladed masses, rarely showing good crystal form. It is usually acicular or fibrous, even in the smallest of particles. The most unique property of crushed and ground wollastonite is its cleavage. Fragments of crushed wollastonite tend to be needle-shaped, imparting a high strength, and this property is the basis for many of its uses. The fiber lengths are commonly in the ratio of 7 or 8 to 1, length to diameter. The average diameter of wollastonite is 3.5 µm. Some crystals of wollastonite fluoresce under short-wave or longwave ultraviolet light, or both, with colors ranging from yellow-orange to pink-orange. Specimens may also show phosphorescence. The acicularity of wollastonite is a property of considerable importance to the marketplace. The plastics industry makes utilization of high aspect ratio grades of wollastonite (20:1) for reinforcing thermoplastics and thermoset polymer compounds. The naturally high pH of 9.9 (10% water slurry) is a prime property to the coatings industry. The coatings industry uses milled grades of wollastonite as a pH stabilizer in interior and exterior PVA and acrylic latex systems. Processed wollastonite can have a G.E. brightness of 90 to 93. Chemically, wollastonite is inert and this property makes it useful as a filler and reinforcing agent. There are two polymorphs of calcium silicates: wollastonite, a low temperature form, and pseudowollastonite, a high temperature

Jan 1, 1983

By P. S. Roller

P. S. ROLLER,* College Park, Md.-The author introduces the idea of a grind limit, or lower size limit of the particles formed directly by grinding, and this is stipulated to be 0.70 micron. I wonder where all the particles come from that lie between the resolving power of the microscope and 0.7 micron, which are seen under a microscope in examining a sample of grind? There is also introduced the idea of excess fines; this is all right in itself but the author's quantitative definition seems to be virtually impossible to justify, and, moreover, is obscure. Just why E, the excess fines, should be defined as the distance between an F line and a y line is hard to follow, and just where the distance should be measured does not appear to be stated, as it should be since the F and y lines intersect and the distance between will depend upon where that distance is measured. The basis of the presentation is the relation of log weight against log size that was "discovered" by Schuhmann. While this relation is implied to fit, the only evidence that I can see is a slightly irregular line in Fig. I between 2 per cent and 18 per cent by weight and then a precipitous drop at 18 per cent away from any sort of straight line. Some of the conclusions are rather startling, It is stated that E, the excess fines, remains constant for all the comminution products of any particular material, except that it may decrease for some coarse crusher products. No reason is given for this assertion. One would, on the contrary, expect that excess fines, if such a concept is permissible, would generally vary with different conditions instead of being constant. Again, "as much net energy is required to reduce a ton of quartz to particles of the grind-limit diameter (namely, of course, 0.7 micron) by grinding as is required to melt the quartz." This would require many data to prove, but no proof is given; any consideration would reveal the impossibility of such a result. Still further, ore samples "ground to widely different sizes, and with different circulating loads and different size distributions or product, show the same production of new surface area per revolution of the mill, when this grind limit is used." This statement is confuted by ordinary experience, which teaches that grinding efficiency varies generally with the condition of material. For example, the cushioning effect of fines is widely accepted, while the inefficiency of a ball mill when the feed is too coarse is also well known. R. SCHUHMANN, JR.,* Cambridge, Mass.-Contrary to Mr. Bond's stand, there is a great deal of miscellaneous experimental evidence that comminution does not stop at around 0.7 micron, nor does it cease consuming energy at that point. Comminution is in fact recognized as an important method of producing colloids.5 Mechanical comminution methods were used by von Weimarn6 to produce colloidal dispersions of a variety of solids, including the minerals chalcocite, galena, hematite, stibnite. Utzino7 gives average particle sizes ranging from 0.02 to 0.09 micron for colloids produced by mechanical comminution of several crystal-line solids. Andreasen and Berg8 have ground

Jan 1, 1941

By P. S. Roller

P. S. ROLLER,* College Park, Md.-The author introduces the idea of a grind limit, or lower size limit of the particles formed directly by grinding, and this is stipulated to be 0.70 micron. I wonder where all the particles come from that lie between the resolving power of the microscope and 0.7 micron, which are seen under a microscope in examining a sample of grind? There is also introduced the idea of excess fines; this is all right in itself but the author's quantitative definition seems to be virtually impossible to justify, and, moreover, is obscure. Just why E, the excess fines, should be defined as the distance between an F line and a [?] line is hard to follow, and just where the distance should be measured does not appear to be stated, as it should be since the F and [?] lines intersect and the distance between will depend upon where that distance is measured. The basis of the presentation is the relation of log weight against log size that was "discovered" by Schuhmann. While this relation is implied to fit, the only evidence that I can see is a slightly irregular line in Fig. I between 2 per cent and 18 per cent by weight and then a precipitous drop at 18 per cent away from any sort of straight line. Some of the conclusions are rather startling. It is stated that E, the excess fines, remains constant for all the comminution products of any particular material, except that it may decrease for some coarse crusher products. No reason is given for this assertion. One would, on the contrary, expect that excess fines, if such a concept is permissible, would generally vary with different conditions instead of being constant. Again, "as much net energy is required to reduce a ton of quartz to particles of the grind-limit diameter (namely, of course, 0.7 micron) by grinding as is required to melt the quartz," This would require many data to prove, but no proof is given; any considera¬tion would reveal the impossibility of such a result. Still further, ore samples "ground to widely different sizes, and with different circulating loads and different size distributions or product, show the same production of new surface area per revolution of the mill, when this grind limit is used." This statement is confuted by ordinary experience, which teaches that grinding efficiency varies generally with the condition of material. For example, the cushioning effect of fines is widely accepted, while the inefficiency of a ball mill when the feed is too coarse is also well known. R. SCHUHMANN, JR.,* Cambridge, Mass.¬Contrary to Mr. Bond's stand, there is a great deal of miscellaneous experimental evidence that comminution does not stop at around 0.7 micron, nor does it cease consuming energy at that point. Comminution is in fact recognized as an important method of producing colloids.5 Mechanical comminution methods were used by von Weimarn6 to produce colloidal dispersions of a variety of solids, including the minerals chalcocite, galena, hematite, stibnite. Utzino7 gives average particle sizes ranging from 0.02 to 0.09 micron for colloids produced by mechanical comminution of several crystalline solids. Andreasen and Berg8 have ground

Jan 1, 1941

By Joseph C. Kieffer

The Duquesne property of the Callahan Zinc-Lead Co. is about 20 miles east of Nogales, in southern Arizona. One mine is near the mill, but most of the mill feed is hauled in by truck from a number of small mines. The same sulphides are found in all the ores, in general, but the amounts vary considerably. All ores contain silver, copper, lead and zinc minerals but one mine ships ore high in silver and lead and low in copper and zinc; while another mine ships ore high in copper and zinc, and low in silver and lead. The common sulphides are galena, carrying most of the silver; chalcopyrite; sphalerite, carrying iron in solid solution; and pyrite, in a gangue consisting of limestone, quartz and garnet. Mineralization is fairly coarse. At the present grind of about 66 per cent minus 200 mesh most of the sulphides are liberated A small amount of chalcopyrite is locked up with the sphalerite and cannot be liberated at an economic grind, and the copper carried into the zinc concentrate with the sphalerite accounts for the comparatively poor recovery of copper in the copper-lead concentrate. Production oF Two Concentrates The milling problem, which was complicated by the extreme variation in the grade of the feed, was first attacked with the idea of producing a silver-copper-lead con- centrate and a zinc concentrate, both with satisfactory grades and recoveries. By February 1941, it was felt that these objectives had been attained, when the grades of the various products and the recoveries were as shown in Table I. A rough outline of the flowsheet and reagents used is as follows: Minus ¾-in. feed to a 7-ft. by 36-in. Hardinge ball mill working in closed circuit with a 36-in. Wemco classifier. The classifier overflow passes to the second cell of an 8-cell bank of No. 18 Special Denver Sub-A flotation machines (volume, 22.5 cu. ft. per cell). A rougher concentrate is removed from the second to the fifth cells inclusive, and returned to the first cell, which is the cleaner. A scavenger concentrate is removed from the sixth, seventh, and eighth cells, and returned to the third cell. Consump-

Jan 1, 1943

By Joseph C. Kieffer

The Duquesne property of the Callahan Zinc-Lead Co. is about 20 miles east of Nogales, in southern Arizona. One mine is near the mill, but most of the mill feed is hauled in by truck from a number of small mines. The same sulphides are found in all the ores, in general, but the amounts vary considerably. All ores contain silver, copper, lead and zinc minerals but one mine ships ore high in silver and lead and low in copper and zinc; while another mine ships ore high in copper and zinc, and low in silver and lead. The common sulphides are galena, carrying most of the silver; chalcopyrite; sphalerite, carrying iron in solid solution; and pyrite, in a gangue consisting of limestone, quartz and garnet. Mineralization is fairly coarse. At the present grind of about 66 per cent minus 200 mesh most of the sulphides are liberated A small amount of chalcopyrite is locked up with the sphalerite and cannot be liberated at an economic grind, and the copper carried into the zinc concentrate with the sphalerite accounts for the comparatively poor recovery of copper in the copper-lead concentrate. Production oF Two Concentrates The milling problem, which was complicated by the extreme variation in the grade of the feed, was first attacked with the idea of producing a silver-copper-lead con- centrate and a zinc concentrate, both with satisfactory grades and recoveries. By February 1941, it was felt that these objectives had been attained, when the grades of the various products and the recoveries were as shown in Table I. A rough outline of the flowsheet and reagents used is as follows: Minus ¾-in. feed to a 7-ft. by 36-in. Hardinge ball mill working in closed circuit with a 36-in. Wemco classifier. The classifier overflow passes to the second cell of an 8-cell bank of No. 18 Special Denver Sub-A flotation machines (volume, 22.5 cu. ft. per cell). A rougher concentrate is removed from the second to the fifth cells inclusive, and returned to the first cell, which is the cleaner. A scavenger concentrate is removed from the sixth, seventh, and eighth cells, and returned to the third cell. Consump-

Jan 1, 1943

By AIME AIME

AT A meeting of the Boston Local Section of the Institute, on Oct. 3, approval was voted to the work done by its representatives on the Committee opposing the passage of a bill by the, Massachusetts Legislature to license engineers. The report is as follows: The Joint Committee on Licensing of Engineers, which included a Committee of the Boston Society of Civil Engineers and representatives of seven other societies,* submitted to the members of the respective societies, on Jan. 8, 1921, a report in which it was stated that on Jan. 4, 1921, a petition was filed in the Legislature of Massachusetts by the Boston Chapter of the American Association of Engineers accompanied by a bill to provide for the registration of professional engineers and land surveyors. This report also stated that at a meeting of this committee, held on Jan. 7, 1921, it was voted:

Jan 1, 1921

By R. P. Laforce, ZJ. R. Low, A. M. Turkalo, D. F. Stein

The interaction of the crlloying eletnenls, nickel and chromium, with the impurity elements, antimony, pIzosphorus, tin, and arsenic, to producse reversible temper brittleness in a series of high-purity steels containing 0.40 wt pct C has been investigated. The alloyed steels contained approximately 3.5 pcl Ni, 1.7 pct Cr, and 0.05 to 0.08 pct of the particular irnpurity to be investigated. Susceptibility to teirlper embrittlement was measured by comparing the notched-bar transition temperature of each steel after quenching from the final temper and after very slow cooling (step cooling;) following the final temper. A plain carbon steel without alloying elements, bu/ ud/h 0.08 pel Sh, does not embrittle when step-cooled through the emzbrittling range of temperatures. The same embrittling treatment, applied to a steel with about the same antinzony content but with nickel and chvonziunz added, causes a 700°C increase in transition temperature. If chromium or nickel is the only alloying element, the increase in transition temperature is only 50%, again with antimony present. A carbon-free iron containing nickel, chromium, and antimony shou~s a 200°C shift in transition temperature for the same thermal treatment. Specific alloy-impurily interactions are also observed for the other impurity elements, phosphorus, tin, and arsenic. Additional investigations involving electron microscopy, trzicrohard-ness tests of vain boundaries, minor additions of zirconiutn and the rare earth and noble metals, nzainly with negative results, are also described. HE particular type of embrittlement investigated is that which is encountered in alloy steels tempered in the temperature range from about 350" to 525'C or slowly cooled through this range of temperatures when tempered above this range. This type of embrittlement is sometimes called reversible temper brittleness to distinguish it from the embrittlement indicated by a minimum in the room-temperature V -notch Charpy energy vs tempering-temperature curve encountered in the range 28 0" to 350°C. Temper brittle-ness seriously restricts the use of many alloy steels since it precludes tempering or use in the embrittling range of temperatures and may significantly raise the ductile-brittle transition temperature of heavy-section forgings and castings tempered above the embrittling range, since such sections cannot be sufficiently rapidly cooled after tempering to avoid embrittlement. The very voluminous literature of temper brittle-ness up to about 1960 has been reviewed by woodfine' and LOW.' Of particular significance to the present investigation was the demonstration by Balajiva, Cook, and worn3 that high-purity Ni-Cr steel does not exhibit temper brittleness and the subsequent detailed and systematic study by Steven and Balajiva~ of the effect of impurity additions on the susceptibility to embrittlement of Ni-Cr steels. Steven and Balajiva showed that, of the impurities which may be found in commercial steels, Sb, As, P, Sn, Mn, and Si could all produce temper brittleness in a high-purity Ni-Cr steel. The principal purpose of the present investigation was to study the effects of particular alloy-impurity combinations on susceptibility to temper embrittlement. The steels used were high-purity 0.30 to 0.40 wt pct C steels containing 3.5 wt pct Ni and 1.7 wt pct Cr, separately or in combination. The susceptibility of these steels was then determined when approximately 500 ppm by weight of antimony, arsenic, phosphorus, or tin were added as an impurity. The melting, casting, and forging practices used in the preparation of the materials investigated are described in Appendix A. Table A-I in this appendix shows the analysis of all steels to be discussed. The steels were produced as 20- or 2-lb heats. The smaller heats were used after it had been demonstrated (see Appendix B) that a small, round, notched test specimen could be used to measure the shift in the ductile-brittle transition temperature caused by temper brittleness with about the same result as that obtained by Charpy testing. HEAT TREATMENT Unless otherwise noted, all steels were tested for embrittlement in the tempered martensitic condition. A typical heat treatment for a 0.40 C, 3.5 Ni, 1.7 Cr steel was: 1 hr at 870"C, in argon, quench into oil at 100"C, quench into liquid nitrogen, temper 1 hr at 625"C, and water-quench. The warm oil quench was used where quench-cracking was encountered; otherwise the initial quench was into room-temperature oil or water. For other compositions austenitizing temperatures were 50°C above Acs with the remainder of the thermal cycle the same. Steels in this condition, with no further heat treatment, are designated as non-embrittled. The above quenching and tempering cycle for the 0.40 pct C steels resulted in as-quenched hardnesses of 48 to 53 RC and as-tempered hardnesses of 24 to 31 Rc except in the case of the plain nickel or plain carbon steels. In these, the as-tempered hardness was as low as 80 to 90 Rg. No attempt was made to adjust the tempering temperature to obtain the same hardness in ali steels since it was felt that a uniform thermal cycle was more important than exactly equivalent hardness values. Pro- the standard quench and temper described above, the standard embrittling treatment was "step-cooling". For this the thermal cycle was: 593"C, 1 hr; furnace-cool to 538"C, hold 15 hr; cool to 524"C, hold 24 hr; cool to 496"C, hold 48 hr; cool to 468'C, hold 72

Jan 1, 1969

Richard Moldenke, New Pork, N. P. (communication to the Secretary*):—Iu following the discussion of the specifications for cast-iron and finished castings, I mas strongly impressed with two points which might be ventilated to advantage more fully from the view of the practical foundry-man. First, the reasons why only silicon and sulphur were specified and not phosphorus, manganese and carbon; and second, why but little was said concerning the presence of iron oxide in the material.

Jan 1, 1905

By Henry G. Morris

The use of compressed air for the transmission of power has reached so great a development that we find numerous large establishments devoted to the manufacture of machinery for its production and application, and special periodicals published for the dissemination of information on the subject. Moreover, its employment is so general in mining operations that no apology is needed for the presentation to the Institute of such a paper as the present. The admirable articles of Mr. E. A. Rix, published in Conzpressed Air, show a wide range in the mechanical efficiency of air-compressors, varying, under different conditions, from 15 to 60 per cent.; and it is evident that any

Jan 1, 1902

By Scott Turner

HOSTS of friends will rejoice that T. A. Rickard has been given honorary membership in the Institute. It might well have been done long ago, since, when one reviews distinguished services rendered by individuals to our organization and our profession, it is at once apparent that his name ranks high and that he has merited this distinction for more than three decades. Our by-laws restrict this list to twenty names; "T.A." becomes the sixteenth living member. Young engineers should particularly be pleased; Mr. Rickard has had a career rich in human interest, and full of useful suggestions to the younger men; he has given them good advice and set them a notable example; he, more than anyone else, has shown them how technical writing can be clear and concise; he has inspired youngsters to do their best; he has been their friend. No one has more first-hand knowledge of these facts than the writer of this appreciation:

Jan 1, 1935

By E. F. Sumner, C. K. Eilerts

A partial differential equation was developed and programmed to compute the cumulation and flow of the liquid phase of a gas-condensate fluid. It was found that such cumulation near the wellbore may attain saturations permitting liquid flow within periods of the order of 1 day. The radius at which this saturation obtains advances toward the external reservoir boundary with continued recovery, although it may move only 2 to 5 percent of that distance during the productive life of the well. This relatively high saturation can cause a serious dimunition in delivery capacity. The pressure dilferential required for flow of gas through a formation with such saturation may be as much as three times greater than the corresponding differential in a formation where saturation is less than 2 percent. Because of the radial geometry, total reservoir pressure differential required for flow with a zone of relatively high liquid saturation about the well was indicated to be two to three times greater than without the saturation. INTRODUCTION A computing program developed by the authors 1 to integrate the partial differential equation for transient radial flow of gas-condensate fluids required a prevalued function, W(Po) = kD(p0)/M(p0)z0(Po).......(1) related to cumulation of condensate in pores of the reservoir as pressure declines. Methods were available for relating mobility to saturation, saturation to liquid-vapor volume ratio, liquid-vapor volume ratio to pressure and, hence, mobility to pressure to obtain W(pD). However, certain assumptions had to be made in advance of program execution concerning movement of the liquid phase and change in radial distribution of liquid saturation as recovery progressed. Because reservoir fluid mobility and related pressure gradients are markedly dependent on liquid saturation, it was desirable to eliminate the necessity for these assumptions and in this respect improve the reliability of a result obtained by integration. Experimental research was begun to determine the relationship of variables that control the reservoir flow of low liquid-vapor ratio fluids. With the porous medium partly saturated, permeability to a two-phase flowing fluid could not be measured because the viscosity was unknown. Viscosity could not be measured without knowing permeability of the liquid-containing medium; but mobility, the ratio of permeability to viscosity, was measurable. This property, and liquid-vapor volume ratio of the flowing phases, have values determined by nature of the fluid and porous medium and, in addition, were found to be pressure, velocity and saturation dependent. A program developed by Kniazeff and Naville 2 for computing multicom-ponent, two-phase flow used polynomials to represent saturation dependence of permeabilities for gas and for liquid phases, and an effluent viscosity constant under reservoir conditions. The authors developed a program based on a partial differential equation of similar mass balance origin but designed to represent distribution of an unlimited number of components between gas and liquid phases utilizing the experimental information available as to variable dependence. Attention was given to liquid-vapor volume ratio of the flowing phases, a property which is essential as a liquid saturation boundary condition. A program for computing implicitly saturation increase at uniform intervals along the drainage radius was combined with an existing program for calculating pressures, and the two were used alternately in an iterative solution for both saturations and pressures. The function W(pD) needed for calculating pressures was replaced by the ratio of mobility to compressibility factor. BASIC EQUATIONS The partial differential equation for calculating

By Scott Turner

IT has been considered that the training of an engineer is too often vocational training; that it is a pity all engineers cannot have had a period of liberal training before taking up' pure engineering. Offhand, the so-called liberal courses should bring more ready adaptability to deal with the unexpected, to face with assurance situations which have had no parallel in one's experience, and to move without hesitation under conditions which were heretofore unknown to one, than the specialized course in mining engineering. We hear increasing talk as to the necessity of making the engineer articulate and bringing him into public life. The social implications, and responsibilities of engineering are pointed out, as of equal importance with the prodigious marvels of engineering ingenuity. You often read of this as the logical result of the in¬creasing consciousness of the engineer as to his rela¬tive position in our modern industrial civilization. , Some wag has noted that man is the noblest work of God, but that man is the only one who has said so. Perhaps engineers are the only claimants as to the necessity of their going in for public life and service; at any rate, some liberal educators' still maintain that a well-rounded general education is the better training.

Jan 1, 1930

By W. M. Baldwin, J. T. Brown

The effect of hydrogen on the ductility, c, of SAE 1020 steel at strain rates, i, from 0.05 in. per in. per rnin to 19,000 in. per in. per rnin and at temperature, T, from +150° to —320°F was determined. The ductility surface of the embrittled steel reveals two domains: one in which and the other in which The usual "explanations" of hydrogen embrittlement are in accord with the first of these domains only. THE purpose of this investigation was a fuller A characterization of this of the investigation effects of varying temperature and strain rate on the fracture strain of hydrogen-charged steel. To be sure, it is known that low and high temperatures remove the embrittlement that hydrogen confers upon steels at room temperature,1 * see Fig. la and b, and that high strain rates have a similar effect,'-' see Fig. 2a, b, and c. However, the general effect of these two testing conditions on the fracture ductility of hydrogen-charged steels is not known, i.e., the three-dimensional graphical representation of fracture ductility as a function of temperature and strain rate is not known—only two traverses of the graph are available. The need for such a graph is not pedantic. To demonstrate this point, Fig. 3a, b, and c shows three of many three-dimensional graphs, all possible on the basis of the two traverses at hand. The important point (as will be developed in the Discussion) is that each of them would indicate a different basic mechanism for hydrogen embrittlement. It will be noted that the four types of ductility surfaces in Fig. 3a, b, and c may be characterized as follows: Material and Procedure Tensile tests were made at various temperatures and strain rates on a commercial grade of % in. round SAE 1020 steel in both a virgin state and as charged with hydrogen. The steel was spheroidized at 1250°F for 168 hr to give the unembrittled steel the lowest possible transition temperature. The steel was charged cathodically with hydrogen as follows: The specimen was attached to a 6 in. steel wire, degreased for 5 min in trichlorethylene, rinsed with water, and fixed in a plastic top in the center of a cylindrical platinum mesh anode. The assembly was placed in a 1000 milliliter beaker containing an electrolyte of 900 milliliters of 4 pct sulphuric acid and 10 milliliters of poison (2 grams of yellow phosphorous dissolved in 40 milliliters of carbon disulphide). A current density of 1 amp per sq in. was used which developed a 4 v drop across the two electrodes. All electrolysis was carried on at room temperature. Temperatures for tensile tests were obtained by immersing the specimens in baths of water (+70° to + 150°F), mixtures of liquid nitrogen and isopen-tane (+70° to —24O°F), and boiling nitrogen (-240" to-320°F). Specimens were tested in tension at strain rates of 0.05, 10, 100, 5000, and 19,000 in. per in. per min. The 0.05 and 10 in. per in. per rnin strain rates were obtained on a 10,000 lb Riehle tensile testing machine, the 100 in. per in. per rnin rate on a hydraulic-type draw bench with a special fixture, and the 500 and 19,000 in. per in. per rnin rates on a drop hammer. The fracture ductility of hydrogen-charged steel at room temperature and normal testing strain rates (-0.05 in. per in. per min) is a function of electro-lyzing time, dropping to a value that remains constant after a critical time.'* Under the conditions of • The hydrogen content of the steel continues to increase with charging time even after the ductility has leveled off to its saturated value.' this research the saturated loss in ductility occurred at approximately 30 min, see Fig. 4, and a 60 min charging time was taken as standard for all subsequent tests. After charging the steel with hydrogen, the surface was covered with blisters. These have been described by Seabrook, Grant, and Carney.' The original diameter of the specimen was not reduced by acid attack, even after 91 hr. Results The ductility of both uncharged and charged specimens is given as a function of strain rate in Fig. 5, and as a function of temperature at four different strain rates in Fig. 6. These results are assembled into a three-dimensional graph in Fig. 7. It is seen that the locus of the minima in the ductility curves of the charged steels divides the ductility surface into two domains. At temperatures below the minima,

Jan 1, 1955