Search Documents

By R. F. Nielsen, R. G. Bentsen

Jan 1, 1966

By J. F. Wilson

An experimental investigation has been made of gas-driven slug displacements in a system of high gas saturation to evaluate the process for use in a California reservoir. Fluid compositions, temperature, pressure and core permeability duplicated reservoir conditions as closely as possible. The temperature was above the critical of the slug materials. The slug composition required for 100 per cent oil recovery in the linear flow systems was found to agree with that determined from equilibrium phase studies. A qualitative theory for the slug displacement of two-phase systems is proposed and found to be in general agreement with the observed flow behavior. The theory predicts that the length of the reservoir fluid-slug transition Zone will increase with increased initial gas saturation and decrease with increased oil swelling accompanying the composition change from reservoir oil to the critical composition. The precipitation of small amounts of an asphaltic phase during the formation of the transition zone had no adverse effects on the flow behavior of otherwise miscible systems. INTRODUCTION Despite the large number of recent publications relating to oil recovery by miscible displacement, little information is available concerning the behavior of crude oil-natural gas systems at conditions likely to be encountered in field application. The laboratory data reported here were obtained during an investigation of the possibility of using a gas-driven LPG slug in a partially depleted California reservoir. Seven gas-driven slug displacements employing slugs of different compositions and sizes were made in 26- to 27-ft long sandstone cores. The equilibrium phase behavior of the systems was also determined. The features of primary interest in this study are the following. 1. Data were obtained on the displacement of reservoir fluids at reservoir conditions. 2. A high gas saturation existed in the long cores at the start of the displacements. 3. The temperature of the studies was above the critical of the slug materials. 4. A comparison between the flow behavior and equilibrium phase behavior, as illustrated by a pseudo-ternary phase diagram, is afforded for a system of considerable complexity. THEORY Phase Behavior The use of the pseudo-ternary phase diagram to illustrate the phase behavior in miscible displacements has been discussed by Clark, Schultz and Shearin. Sie-vert, Dew and Conley and Arnold, Stone and Luffel' have presented both phase equilibrium and flow data for true ternary systems. For the true ternary, the application of the theory is straight-forward; for a reservoir system represented as a ternary, the theory undoubtedly gives a qualitatively correct picture. One purpose of this investigation was to see if the pseudo-ternary phase diagram could be used to predict with reasonable accuracy the conditions necessary for miscible displacements with actual reservoir systems. MiscIBLE Displacement of Two-Phase System A large number of papers "I3 have treated the miscible displacement of a single-phase fluid from both an experimental and a theoretical viewpoint. However, the normal field application of the process will be in a partially depleted reservoir. Often the state of the system will be such that the mobility of the gas phase is greater

Jan 1, 1967

By E. F. Johnson, V. O. Naumann, D. P. Bossler

A method is presented for calculating individual gas and oil or water and oil relative permeabilities from data obtained during a gas drive or a waterflood experiment performed on a linear porous body. The method has been tested and found both rapid and reliable for normal-sized core samples. INTRODUCTION Individual oil and gas or oil and water relative permeabilities are required for a number of reservoir engineering applications. Chief among these is the evaluation of oil displacement under conditions where gravitational effects are significant, such as a water drive or crestal gas injection in a steeply dipping oil reservoir. Numerous proposed methods of obtaining relative permeability data on reservoir core samples have been too tedious and time consuming for practical use, or have yielded questionable and sometimes inconsistent results. A method has been developed by which the individual relative permeability curves can be calculated from data collected during a displacement test. The method is based on sound theoretical considerations. Using this method, with a properly designed experimental procedure, relative permeability curves can be obtained using core samples of normal size (i.e., 2 to 3 in. in length and 1 to 2 in. in diameter) within a few days after receipt of the core. In a recent publication D. A. Efros1 describes an approach to the calculation of individual relative permeabilities that is based on the same theoretical considerations. We believe the approach described in the present paper is more adaptable to practical application than the method implied by Efros. In addition, comparisons with independently determined relative permeabilities are furnished to substantiate the reliability of the new method. DERIVATION Previously the theory of Buckley and Leverett as extended by Welge2 as been used to calculate the ratio of relative permeabilities. In the derivation which follows, this theory is further extended to permit calculation of the individual relative permeabilities. The theory assumes two conditions which must be achieved before the method is applicable. They are that the flow velocity be high enough to achieve what has been termed stabilized displacement,3 and that the flow velocity is constant at all cross sections of the linear porous body. In stabilized displacement the flowing pressure gradient is high compared with the capillary pressure difference between the flowing phases. The high pressure drop insures that the portion of the core in which capillary effects predominate will be compressed to a negligibly small fraction of the total pore space. The assumption of constant flow velocity at all

By D. H. Gurinsky, D. G. Schweitzer

The empirical equilibrium constantsd the heat of reaction for the reduction have been determined from 300° to 500°C. The mechanisms of the oxidation of uranium and magnesium from dilute bismuth solutions have been investigated. The kinetics of some of the reactions were affected by air adsorbed on the uranium oxides. THE Liquid Metal Fuel Reactor studied at Brook-haven National Laboratory uses a solution of uranium in bismuth as the fuel. Corrosion and stability problems require that the fuel solution contain corrosion inhibitors and deoxidants. Of the additives tested, magnesium has been found to be the best deoxidant and zirconium the best corrosion inhibitor in bismuth. Some experiments1 indicate that magnesium may play a secondary role in increasing the effectiveness of zirconium in inhibiting corrosion. The work reported here was intended to determine the relative concentrations of Mg and U required to prevent oxidation of the uranium fuel in the event of an air leak. In addition, an attempt was made to identify some of the mechanisms of the oxidation and reduction reactions occurring in the liquid bismuth solutions. EXPERIMENTAL Apparatus and Procedure—The equipment shown in Fig. 1 was designed so that the reaction kinetics could be studied as functions of temperature, melt composition, pressure, and flow rate. At the start of a run, the 10-liter bell jar (F) is removed by opening the bottom Dresser fitting (L), and the bismuth and additives are placed in a pyrex crystallizing dish (I). The bell jar is replaced, the system is evacuated to 10-5 to 10-6 mm Hg and then the heater (J) is turned on. When the selected temperature is reached, the oxidizing gas is admitted to the system to the desired pressure as read on the manometer (D). Gas is introduced through the slide tube (Q) which has a pyrex frit (R) sealed to its bottom. Stirring is accomplished by immersing the end of the tube in the melt. To maintain a constant pressure under flow the input and evacuation rates must be equalized. To obtain this condition stopcock (C) is closed and flowmeters (B) are matched. The reaction is "stopped" by closing the inlet flowmeter and quickly evacuating the system. To obtain a liquid metal sample, the system is evacuated with the sampler positioned near the surface of the liquid. The sampler, Fig. 2, is then immersed until its thermocouple reading matches thermocouple (G) Fig. 1. The system is then pressurized with helium which forces the solution through the frit. Twenty to 30 min elapsed between the time the system was evacuated and sampled. During evacuation and pressurization of the system, the temperature variations did not exceed ± 5°C. While bubbling occurred the temperature remained constant to within 1/2 oC. The volume of the equipment was determined by adding a known volume of air at atmospheric pressure to the evacuated system and noting the resulting pressure.

Jan 1, 1962

By C. E. Mills

STUDIES of ground movement and subsidence resulting from mining operations cover a broad field. It is also a very important consideration and one that eventually affects nearly every mining operation of any extent. The damage to surface buildings, removal of mine surface plants and replacements of main hoisting shafts must reach an astounding expenditure were these cost figures available over a period of years. Were the subject one of mathematical formula and dependent only on the angle of draw of the walls or country rocks, the problem would be relatively simple. Consideration must be given to depth and extent of workings; structural conditions of the orebodies and enclosing country rock; physical properties of these same rocks, including schistosity, bedding, jointing, slips, dikes, faults, and other structural weaknesses. The method of mining, extent of openings, supporting pillars, and amount of moisture or water underground are other pertinent factors. With such a large number of variable factors, it is apparent that the subject of subsidence is one that must be based largely on experience and results at other mines where conditions are somewhat comparable. In presenting this paper, it is the intent to describe the progressive results of past ground movements at the United Verde, to bring out physical conditions largely responsible for this movement, but to refrain from theorizing on the ultimate extent of subsidence resulting from future mining operations.

Jan 1, 1934

Low Zinc Prices Close Alcoa Mine Alcoa Mining Co., announced that it will suspend operations at its Hutson mine, near Salem, Ky., because of low zinc prices, January 15. The Aluminum Co. of America subsidiary announced that the low market has made zinc mining un- profitable. About 70 men were employed at the mine, with a production of about 5000 tons of zinc annually. Alcoa said the shutdown would not affect other company operations, with most of the men at Hutson absorbed in the mining firm's fluorspar operations in the same area.

Jan 2, 1953

By H. Rush Spedden, Arvid Thunaes

R. R. Knobler and F. E. Albertson—Following the testwork done by Thunaes and Spedden, a Sullivan deck plant was built for the Colquiri mill. This plant started to operate in April 1945 and continues in successful operation. Since May 1950 the Colquiri mill has operated with a completely revamped flowsheet at a rate of 1000 tons per day. The old Sullivan deck section was retained with this new flowsheet. The "slime plant" in Colquiri consists of one 12-cell Denver No. 18-Sp. Sub-A flotation machine, one 16-ft and one 12-ft hydroseparator, six five-deck Sullivan-frames and six shaking tables for cleaning up the Sullivan deck concentrates, as well as 12 Deister plus three Plat-O tables on which the fine sands, which are not treated on the S-decks, are concentrated. Only —325-mesh fines are treated on the Sullivan decks. The combined hydroseparator overflows are fed to the S-decks. From 1946 to 1949, i.e. with the "old" flowsheet and an average mill feed of 800 tons per day an average of 45 tons per day was treated on four Sullivan rougher frames. The two additional frames were used as cleaners. At times, up to 90 and 120 tons of slimes were treated successfully on this Sullivan deck installation. The average operating data for the S-deck section in Colquiri for the year 1949 were as follows: The tests reported in this paper indicated a tin recovery of 42 pct. The actual plant results for 1949 show a 54 pct tin recovery from the Sullivan decks. The total average quantity of tin produced from the S-deck section in 1949 was 15 tons of tin per month. This corresponds to 3 pct of the total mill recovery. The difference between the 6 pct overall recovery-increase expected after the tests in 1943 and the actual plant results given for 1949 is explained as follows. According to the tests, a total of 170 tons was expected to be routed to the Sullivan decks, but because of certain changes in the flowsheet and mill amplifications,

Jan 1, 1951

By H. Rush Spedden, Arvid Thunaes

R. R. Knobler and F. E. Albertson—Following the testwork done by Thunaes and Spedden, a Sullivan deck plant was built for the Colquiri mill. This plant started to operate in April 1945 and continues in successful operation. Since May 1950 the Colquiri mill has operated with a completely revamped flowsheet at a rate of 1000 tons per day. The old Sullivan deck section was retained with this new flowsheet. The "slime plant" in Colquiri consists of one 12-cell Denver No. 18-Sp. Sub-A flotation machine, one 16-ft and one 12-ft hydroseparator, six five-deck Sullivan-frames and six shaking tables for cleaning up the Sullivan deck concentrates, as well as 12 Deister plus three Plat-O tables on which the fine sands, which are not treated on the S-decks, are concentrated. Only —325-mesh fines are treated on the Sullivan decks. The combined hydroseparator overflows are fed to the S-decks. From 1946 to 1949, i.e. with the "old" flowsheet and an average mill feed of 800 tons per day an average of 45 tons per day was treated on four Sullivan rougher frames. The two additional frames were used as cleaners. At times, up to 90 and 120 tons of slimes were treated successfully on this Sullivan deck installation. The average operating data for the S-deck section in Colquiri for the year 1949 were as follows: The tests reported in this paper indicated a tin recovery of 42 pct. The actual plant results for 1949 show a 54 pct tin recovery from the Sullivan decks. The total average quantity of tin produced from the S-deck section in 1949 was 15 tons of tin per month. This corresponds to 3 pct of the total mill recovery. The difference between the 6 pct overall recovery-increase expected after the tests in 1943 and the actual plant results given for 1949 is explained as follows. According to the tests, a total of 170 tons was expected to be routed to the Sullivan decks, but because of certain changes in the flowsheet and mill amplifications,

Jan 1, 1951

Jan 1, 1985

By Carl Zapffe

THE object of the Bradley process is to free manganese oxide from its associated gangue and separate the contained iron oxide by dissolving the manganese and precipitating it from the solution. 'The fundamental features of the process are : making. both 1 a manganese ore and an iron ore; effecting a separation of manganese .and. iron by means of selective roasting; leaching- the manganese from the roasted ore by using ' ammonium sulfate; precipitating the manganese by using the ammonia gas generated during leaching; fixing the precipitate by oxidizing with air; breaking down and reforming the ammonium sulfate, so that daily very little additional ammonium sulfate beyond that originally charged into the system is required; washing the manganese precipitate and the iron-silica residue and evaporating the liquor to conserve the dissolved salts in the moistures of these two products and 'to reduce the sulfur content,; drying the precipitates; magnetic wet-concentration of the iron-silica residue; sinteriny the manganese-and .the' iron-concentrates.

Jan 1, 1929

Jan 1, 1948

Jan 1, 1948

By W. L. Saunders

(Wilkes-Barre Meeting, June, 1911.) I. INTRODUCTION. IT is now generally admitted by experts that at least so far as rapid progress is concerned the Alpine system of tunnel-driving is superior to any other. This is perhaps natural in view of the record of experience in driving tunnels through the Alps. These great mountain-chains cannot be treated in the ordinary way by shaft-sinking and driving headings, thus multiplying the points of attack. The work must be done from the ends only, hence speed in driving is of the utmost importance; and, as necessity is the mother of invention, the concentration of effort to make progress has resulted in an organization and in mechanical appliances that have produced results so much in excess of the usual practice, even in America, that a discussion of the subject in detail should be of much value to the engineer and contractor. The first Alpine tunnel was the Mont Cenis, length 7.5 miles, driven with a progress that averaged about 7.75 ft. per day. Next came the Saint Gothard, 9.5 miles long, 18 ft. per day; Arlberg, 6.5 miles long, 27.25 ft. per day; Simplon, 12.25 miles long, 36 ft. per day. The figures represent progress when driving from two headings, so that by dividing them in two we get the daily single-heading progress. The latest of the Alpine tunnels is the Loetschberg, now being driven. In this work the world's record has been beaten by a single day's record in one heading of 36 ft. and by an average daily record in. one heading of 29.5 feet. The Alpine range forms a natural barrier between a large section of northern and southern Europe. This range extends from the southeast of France to the frontier of Hungary, between Italy and the plains of southern Germany. The contour

Jul 1, 1911

By T. Sekimoto, T. Kokubo, M. Yamamoto, K. Masuda, T. Moro, H. Sakamoto

The choking-free cyclone was developed primarily to remove solid particles suspended in a slurry containing fibrous materials, such as municipal solid waste. This cyclone is characterized by a screw conveyor at the underflow side of the cyclone. The screw conveyor has a hollow rotational shaft for air supply and is driven by a variable speed motor for discharge control. Even if the underflow discharge is highly concentrated, this type of cyclone can be stably operated without nozzle choking. High classification efficiency similar to that of a conventional cyclone can be obtained as a result of air introduction through the hollow rotational shaft. The recovery of organic matter and the removal efficiency of inorganic matter were actually improved by the application of this cyclone to municipal solid waste. After applying this cyclone to the desliming of fine sand, sand product of low water content was recovered.

Jan 1, 1980

By John V. Beall

BROMO Seltzer blue has gone to war. The blue of the Bromo Seltzer bottle is a product of cobalt, the Nation's No. 1 strategic metal. When the National Production Authority, on Nov. 21, 1950, ordered a 70 pct cutback in domestic use of cobalt, a stab of pain was felt in the hearts of the glass, porcelain enamel, steel, paint, pottery, and electrical and electronic equipment industries. The reason: A full-scale wartime economy with astronomical requirements for jet engines, high velocity projectiles, armor plate, electronic equipment, and the many products needed to win a war. There is little potential comfort for cobalt users in nonessential manufacturing, and the military will be pinched for optimum supplies of the metal. However, if proper measures are taken immediately and current plans are completed, in two years there will be far more cobalt available than ever before. When normal times return, cobalt supplies should be sufficient to meet peacetime military requirements, and greatly expanded domestic requirements that will result from new technological development for wartime but adaptable to peacetime products. The pres-

Jan 1, 1951

By H. C. Schultz

CERTAIN local conditions were known to govern in large measure the successful adaptation of liquid-oxygen explosives to the large-scale blasting at Chuquicamata. The wide variation in hardness of the rock at this mine makes necessary the use of several types of explosives. A locally manufactured, relatively cheap black powder is used in blasting the softer waste and capping material, where a thorough displacement breaks the ground sufficiently. Before the introduction of L. 0. X., an ammonia dynamite of about 65 per cent. strength was being used exclusively in the harder underlying orebody, where a strong disruptive as well as a displacement effect is required for breaking the ore. The L. 0. X., as developed for quarry work in the United States, has a practically pure carbon cartridge material, and the explosive has an extremely high rate of detonation, which should therefore cause it to usefully develop its full disruptive effect in hard ground. The individual blasts at Chuquicamata are large, black-powder shots which dislodge masses of rock averaging 250,000 tons each, and dynamite shots which dislodge masses averaging 80,000 tons each. It was desirable, therefore, to attempt to displace with L. 0. X. the faster, higher-cost ammonia dynamite used in the smaller blasts. It was not considered practical to attempt to displace the low-cost black powder with L. 0. X., as estimated costs showed no probable saving if this were accomplished. Since it was desirable to continue shooting relatively large blasts for effective operation, it was recognized that larger storage facilities than had been in use would be needed for the liquid oxygen. Because of the difficulty of transporting and discharging large storage containers of efficient design, the better plan appeared to be storage and discharge of the liquid at the place of manufacture, and transportation of the filled soaking boxes to the blast.

Jan 1, 1928

By Earl R. Parker, Ralph Hultgren

DURING the past year publications in physical metallurgy have not been abundant when compared with the output of prewar years. Nevertheless, some noteworthy contributions have been made to the literature. Because of the necessity for war production, much of the metallurgical effort has been directed towards the solution of problems of production processes. The limited amount of time devoted to other problems is reflected in the small number of papers devoted to nonapplied research, though a few excellent contributions have been made to the fundamentals as will become evident in the following pages. Results of many of the government-sponsored research investigations have been released to the public and are being published in the technical journals. Many more of these papers may be expected to appear in the 1946 publications.. Public distribution of information obtained in the course of these investigations should be of great value to American industries in the postwar era. Continued activity in research of all kinds is apparently assured because of intense

Jan 1, 1946

By Ta M. Li

How will phosphate producers in southeastern Idaho fare with growing governmental regulations and environmentalism of the late 1970's? With a similarity that is reminiscent of the battles between the coal industry and environmental-conservation groups earlier in the decade, Idaho's future growth and a nation's need for phosphate fertilizer products remain uncertain. The catalyst that brought the issue to the forefront was the preparation of an Environmental Impact Statement (EIS) addressing the development of phosphate resources in southeastern Idaho. Although the final EIS was published in August 1977, resolution of rational and orderly growth in this potentially vital region remains stifled as Secretary of the Interior Cecil Andrus virtually "sits" on it.

Jan 1, 1978

By Charles Pack

DIE castings may be defined as metal castings made by forcing molten metal, under pressure, into a metallic mold or die. It is necessary to keep this definition in mind to avoid confusing this process with other permanent-mold casting processes. The fundamental principles of the process have been known and practised many years. The simplest application is embodied in the modern linotype machine in which molten metal (usually tin-lead alloy) is forced under pressure into a metallic mold. The pressure is derived from a piston and cylinder immersed in the molten metal. Progress in the art of die casting may conveniently be divided into threee groups: Machine for imparting pressure to the metal, material for the die or mold, casting alloys. CASTING MACHINES The problem of delivering molten metal under pressure into a die is comparatively simple, when dealing with low-fusing-point alloys, as the alloys of lead and tin, but it is much more complicated when dealing with metals of higher fusing points, such as the alloys of zinc, aluminum, and copper. Although the art of die casting is comparatively new and, to a large extent, unknown, the records of the patent office are replete with patents on the subject. Fig. 1 shows the Underwood machine patented in 1902; this is probably one of the first machines designed for the production of commercial die castings. The relation of this machine to the linotype casting machine is clearly. apparent. A cylinder and piston are immersed in the molten metal, the application of power to this piston forcing the molten metal, under pressure, into the mold or die. The Doehler machine, Fig. 2, patented in 1907, is based on the same general principles. This machine is used to a large extent at the present time, throughout the United States, for the production of zinc, tin, and lead alloy die castings.

Jan 2, 1919