Search Documents

By C. H. Bushell, M. Malnarich

REAGENT control in flotation is more an art than a science. Operators vary the amount of reagents used according to the metallurgy obtained. The amount of collector may be increased, for example, if tailings losses are high and decreased if concentrate grades are low. Often control decisions are based on only one assay, such as the tailings analysis by microscopic or quick assaying techniques. This method of control has given reasonably satisfactory results but is clearly far from perfect. No adjustment in reagent addition can be made until information is received that metallurgy has deteriorated, that is, until the optimum time for adjustment has already passed. The first adjustment probably will be an overcorrection or an undercor-rection, and time will be required to establish the best new addition rates. The seriousness of the problem depends on variability of the ore. In ore of continually shifting composition and complexity, mill results will shift back and forth from excessively high concentrate grades and high tailings losses to excessively low concentrate grades and low tailings losses. Economic incentive for improved control also increases with increasing size of mill. Even a small improvement in percentage recovery in a large mill pays for expensive control equipment. The Sullivan concentrator of The Consolidated Mining & Smelting Co. of Canada Ltd. at Kimberley, B. C., treats 11,000 tpd of complex lead-zinc ore, a scale of operations which justifies an extensive research program on automatic control. Work has followed two separate lines: 1) development of faster analytical methods for pulps, and 2) study of metallurgical control by measurement and control of reagent concentrations in flotation solutions. Although work is incomplete in both phases, a progress report can be given on the development of reagent control. The primary requirement in flotation is selective attachment of particles of one mineral to air bubbles while the other minerals remain detached. Hydrophobicity of mineral surfaces is established by the collector, which coats the minerals by adsorption. The requirement of selective affinity for air bubbles is therefore equivalent to requiring selective adsorption of a collector. Adsorption theory, supported by abundant experimental evidence, shows that the amount of a reagent adsorbed at a surface must be a function of its residual concentration in solution. As the concentration in solution rises, the amount adsorbed increases, usually following some type of logarithmic curve. Selective adsorption must depend on a natural difference in the minerals, but ordinarily the differences in affinity are not great enough to obtain complete coverage of one mineral while the others are completely uncoated. An optimum concentration will exist, below which coverage will not be great enough to float enough of the valuable mineral, and above which too much unwanted mineral will float. All other reagents, except some frothers, affect the amount of collector adsorbing at constant residual collector concentration in solution, either by adsorbing competitively with the collector, or by a

Jan 1, 1957

By B. M. Larsen, T. E. Brower

IN an earlier paper1 we discussed a simple, rapid method of taking samples of liquid steel and analyzing them for oxygen, which, though possibly not absolutely accurate (as is likewise true of all other methods), certainly yields results that are satisfactorily consistent. Accordingly, samples from hundreds of heats in different shops were analyzed for oxygen, with results sufficient in number to be handled statistically and permit estimation of some general trends. Measurements were made in acid as well as in basic open hearths, throughout the refining period, to learn how stirring, blocking, adding ore or lime or sand, affects the oxygen content of the bath; we also followed the changes brought about by tapping, teeming, and deoxidizing. Some of these results, discussed in an earlier paper.2 bring out the dominant role of the carbon-oxygen reaction in regulating degree of oxidation both of metal and of slag, also the marked variability of concentration of dissolved oxygen [0] in excess of that which would be in equilibrium with carbon and with carbon monoxide at a partial pressure of one atmosphere. As a logical beginning on this complex problem, we take up in the present paper the variability of this excess oxygen, ?[O], when other factors are as constant as they ever are in open-hearth operation; namely, toward the end of the refining period, when the bath may be regarded as in the comparatively steady state it approaches in absence of disturbing factors. This condition was chosen because by that time the significant reactions, except carbon oxidation, between slag and metal have come to substantial equilibrium; this facilitates interpretation of the complex situation and thus permits more definite conclusions to be drawn. This excess concentration of oxygen, ?[0], in the metal is needed, of course, to make the steelmaking process go at a reasonable rate; alternatively it may be regarded as a measure of the virtual pressure increment above one atmosphere, or of the degree of supersaturation, of carbon monoxide in the metal. According to our measurements, the excess concentration ?[O] in liquid steel varies from about 0.009 to 0.035 per cent oxygen by weight. It is quite sensitive to change of conditions, being altered temporarily by operations such as stirring with green poles, additions of ore, lime, or sand; but as the disturbance works itself out, it resumes a level within the intermediate range characteristic of the steady state. The conditions most common in average furnace practice are covered by the following : [ ] as in a reasonably steady state-that is, when it is boiling normally, is at proper temperature with a well-shaped slag, and has been free from disturbing effects during the preceding half hour-?[O] returns from

Jan 1, 1946

By J. H. O’Dette

BLISTER formation on wrought aluminum products has been a matter of concern to aluminum fabricators for many years. The fact that blisters make their appearance during the final stages of fabrication means that much time and effort have been expended before it is evident that the material must be scrapped. This and the loss of production are ample reasons for embarking on a research program to find out more about blistering and possible methods of control. Many excellent papers on this subject have appeared in the technical literature in the last few years. In one of the more recent papers, Kostronl gives a fairly complete review of the problem of gas in aluminum and blistering in general. From the work of the various investigators, a general mechanism for the formation of blisters has evolved and may be summarized briefly as follows: Hydrogen gas is usually present in the cast ingot, in the atomic or ionic state, in excess of the solid solubility. At room temperature the gas atoms are relatively immobile, but at elevated temperatures they become mobile and diffuse to free surfaces where they associate to form molecules. If these free surfaces are discontinuities within the ingot then the associated gas molecules collect and build up considerable pressure until equilibrium is reached with the dissolved gas around the discontinuity. Since the solubility of the gas is proportional to the square root of the partial pressure it is evident that large pressures may be built up at the discontinuities. When the metal is rolled to sheet the pressure of the gas in these, discontinuities is sufficient to deform the surface of the sheet and form a blister, particularly when the strength of the material is reduced during the annealing. Although the mechanism of the formation of blisters was fairly well known, the actual impor- tance of the individual roles played by the gas and the discontinuities was not so well established that positive methods for control of blistering were at hand. It was the object of the investigation to learn more about the nature of the discontinuities giving rise to blistering and to develop methods of control. The investigation was carried out in three stages as follows: a) A study of the more commonly used methods of removing hydrogen from aluminum, such as fluxing and holding, and their effects on blistering. b) Location of the discontinuities giving rise to blistering. c) A study, by indirect methods, of the movement of gas in the metal and its effect on blistering, and the development of methods of blister control during fabrication. Removing Gas and Reducing Blistering by Fluxing or Holding-—The work of removing gas and reducing blistering by fluxing or holding was carried out on metal of Alcan 2s (1100) composition with an artificially high gas content. The high gas content was obtained by introducing water into the melt prior to casting; the water reacted with the aluminum forming A12O3 and hydrogen. The procedure was to raise the gas content by introducing water into an aluminum melt and using half the melt to cast one ingot immediately. The remaining metal was treated again with water to make up for the reduction in gas content during holding, while the first ingot was being cast, and then given a fluxing or holding treatment and cast into an ingot. Samples for gas determination were cast from the molten metal before and after the gassing operation; before, after, and during fluxing, and while casting. Samples were also cut from sections of the ingots. Gas determinations were made on these samples using the well known vacuum fusion technique. All ingots were hot rolled at 500°C to 0.250-in. slab which, in turn, was cold rolled to 0.040 in. sheet. The sheet was coiled and annealed for 2 hr at 500 °C and then cut into 5-in. squares which were inspected for

Jan 1, 1958

By AIME AIME

THE joint symposium on gases in metals on Tuesday: Feb. 16, between the Iron and Steel and the Institute of Metals divisions opened the technical sessions for both of these bodies. After a few words of introduction by P. D. Merica, R. S. Dean presented a paper by V. H: Gottshalk and himself on the solubility of gases in metals.

Jan 1, 1932

By Richard W. Lodge

Ix the crucible-method of assaying ores for silver a certain amount of litharge is essential to supply sufficient lead to collect the precious metals. The object of this paper is to point out that the use of a .large excess of litharge in the assay of some ores will give results for silver that are uneven as well as low. So far as I know, however, an excess of litharge does not affect the results obtained in the crucible-assay of ores for gold. The main reasons for using, in the crucible-assay, much more litharge than is required to give the necessary lead button are : 1, its action as a flux; 2, its action as a desulphurizer; and 3, its action as an oxidizer, especially on metals like copper and nickel, whereby they are forced into the slag as oxides and thus prevented from passing into the lead button. Hence, by the use of much litharge in the crucible-assay more-ore can often be taken than in the scorification-process, and a lead button obtained which can possibly be cupelled at once or after a single scorification. The method is specially advantageous with an ore carrying much copper or similar impurity and poor in silver, when the assayer does not wish to resort to a wet-analysis for the determination of the silver. It is well known that some ores give better results when assayed by the scorification-method, while others give better results by the crucible-method. For several years I have noticed that, when much litharge was used with certain sulphide and arsenical ores, the results were considerably lower than when the scorification-method was used. This fact was more forcibly brought out in connection with certain work carried on this year by Messrs. H. A. Frame and

Sep 1, 1907

By Keith C. Hendrick

The mining industry of Canada, stretching from coast to coast and reaching into the most remote regions of the country, is of fundamental importance to the national economy and the well being of many communities outside the main urban areas. The production, processing and transportation of a host of mineral products provide employment for about 9% of the country's labour force; and their shipment to export markets provides an important contribution to the balance of payments. In 1976 Canada's metal and mineral production had a value of $5.24 billion, of which zinc and lead accounted for $862 and $129 million respectively, or 19% of the total. By all standards the Canadian zinc and lead industry is large and, therefore, important to the country as a producer and the world as a supplier. This report will review the development, describe the present status and discus current problems and future potential of the industry. The discovery and successful development of the major lead-zinc deposits at Kimberley, British Columbia, provided Canada with a solid base from which to grow. The breakthrough in metallurgical technology using differential flotation to separate the lead and zinc sulphides and the refining of high purity metal by electrolytic methods not only helped Canada to compete with other world producers but also provided a new source of these metals at prices and qualities that encouraged the development of new end uses.

Jan 1, 1977

By M. Kaufman, A. E. Palty

THE mechanical properties of an alloy under given test conditions are in the main determined by the grain size and the phases present, their distribution and temperature-time dependence. Alloys intended for use at elevated temperatures, especially multiphase alloys depending upon precipitation reactions for strengthening, are particularly susceptible to changes in the phases present. Unfortunately, for modern superalloys, very little published information exists which relates the mechanical properties to the basic structural variables. The present work is an effort to do this for an alloy widely used in aircraft gas turbines and related applications, Udimet 500.* The mechanical properties inves- two heats is within the normal specifications for the alloy. However, the elements which most strongly influence the phase reactions, C, Ti, Al, and Mo, are comparable in the two heats. There was no intentional addition of boron, but normal pickup is about 0.002 pct. The vacuum-melted material was received in the form of centerless ground wrought bar stock % in. diam. PHASE STUDIES A) Methods—Two methods were used to determine the phases present: X-ray diffraction measurements on electrolytically digested residues, and microscopic examination. No single commonly used electrolyte will reveal all the phases that may be present; therefore, two complementary acids were selected: HCl and H3PO4. The necessity for this will be shown below in the results. The acid concentrations used were 10 pct HC1 in alcohol and 10 pct H3 PO4 in water. The current density was maintained below 0.1 amp per sq in. Residues were rinsed and separated by centrifuga-tion. X-ray diffraction patterns were obtained in a 114 mm Debye-Scherrer type camera using cobalt radiation. A temperature of 2250°F was selected to obtain as complete solutioning of phases as possible without encountering incipient melting. Specimens were

Jan 1, 1961

By Meredith Johnson

THE year 1924 saw little change in the production of oil and gas it either Pennsylvania or New York. In the early months of the year the price of Pennsylvania crude oil, $4.00 to $4.50 a barrel, was sufficiently high to cause operators to lay plans for rather extensive drilling opera-tions. But when, in August, the price dropped to $2.85 a barrel, there was no inducement for new work and drilling was curtailed. In spite of the curtailment, however, the combined production of the two states for the year showed a slight increase over 1923, the production being 8;859,000 bbl. in 1923, and 8,901,000 bbl.1 in 1924. The increased production was due entirely to. the continued development of flooding operations in the Bradford field, all other oilfields showing a decline for the year. TABLE 1. Production of Crude Oil in Pennsylvania and New York for the Last Ten Years a Production, Barrels Production, Barrels Year Year Pennsylvania I New York Pennsylvania I New York 1915 7,838,000 888,000 1920- 7,438,000 906,000 1916 7,593,000 874,000 1921 7,418,000 988,000 1917 7,733,000 880,000 1922 7,425,000 1;000,000 1918 7,408,000 809,000 1923 7,609,000 1,250,000 1919 8,137,000 851,000 1924 7,535,0006 1;366,0006 a U. S. Geological Survey figures. b Estimated. Much of the drilling in the southwestern part of Pennsylvania was done in search of gas. Natural gas in Pennsylvania is fast being recognized at its true worth and the increased prices allowed 'the gas companies for their product induced quite a bit of new work. The relative importance of natural gas compared with manufactured gas is shown in Table 2.2

Jan 3, 1925

At the end of June, 1938, a new oil field was opened in Egypt, the Ras Gharib. Five wells were completed during the year and gave a total production of 512,988 barrels.' In the Hurghada field production was as follows: Hurghada Field Age of field to end of 1938, years..................... 25 Producing area for gas and oil, acres................ 1,050 Barrels1 Total oil production to end of 1938............... 31,207,754 Total oil production during 1937................ 1,141,356 Total oil production during 1938.................. 1,019,520 Average oil production per acre to end of 1938... 29,719 Average oil production per acre-foot to end of 1938. . . 243.6 Daily average: production in December 1938.......... 2,603.54 Daily average production per well in December 1938. . 34.90 Millions Cu. Ft. Total gas production (Aug. 1925 to end of 1938)... 4,356.7 Total gas production during 1937.................. 222.5 Total gas production during 1938....... . 167.6 Maximum gas daily average of 1938 (ill May 1..... 0.6 Wells Number of producing wells completed to end of 1938 . . 100 Number of producing wells completed during 1938..... 3 Number of wells abandoned during 1938.............. 2 Producing wells at end of 1938 (all pumping)......... 78 Abandoned wells at end of 1938...................... 22 Dry wells at end of 1938......................... 21 Feet Average depth of bottom of producing horizon........ 1,720 Average depth of top of producing horizonlt 1,598 Character of oil, approximate average ill 1938: specific gravity at 60" F'., 0.900; base, mixed. Character of gas, approximate average for 1938: gallons gasoline per 1000 cu. ft. of gas, 6.4. Main producing formation: Nubian sandstone, Cretaceous (PI; sand rock and sandstone.

Jan 1, 1939

At the end of June, 1938, a new oil field was opened in Egypt, the Ras Gharib. Five wells were completed during the year and gave a total production of 512,988 barrels.' In the Hurghada field production was as follows: Hurghada Field Age of field to end of 1938, years..................... 25 Producing area for gas and oil, acres................ 1,050 Barrels1 Total oil production to end of 1938............... 31,207,754 Total oil production during 1937................ 1,141,356 Total oil production during 1938.................. 1,019,520 Average oil production per acre to end of 1938... 29,719 Average oil production per acre-foot to end of 1938. . . 243.6 Daily average: production in December 1938.......... 2,603.54 Daily average production per well in December 1938. . 34.90 Millions Cu. Ft. Total gas production (Aug. 1925 to end of 1938)... 4,356.7 Total gas production during 1937.................. 222.5 Total gas production during 1938....... . 167.6 Maximum gas daily average of 1938 (ill May 1..... 0.6 Wells Number of producing wells completed to end of 1938 . . 100 Number of producing wells completed during 1938..... 3 Number of wells abandoned during 1938.............. 2 Producing wells at end of 1938 (all pumping)......... 78 Abandoned wells at end of 1938...................... 22 Dry wells at end of 1938......................... 21 Feet Average depth of bottom of producing horizon........ 1,720 Average depth of top of producing horizonlt 1,598 Character of oil, approximate average ill 1938: specific gravity at 60" F'., 0.900; base, mixed. Character of gas, approximate average for 1938: gallons gasoline per 1000 cu. ft. of gas, 6.4. Main producing formation: Nubian sandstone, Cretaceous (PI; sand rock and sandstone.

Jan 1, 1939

The question, Who won the war?, has been the text for innumerable newspaper, and magazine articles, the answers running from "bread and butter" to "poison gas," in a material sense, and from the "Y. M. C. A." to the "boys in the front lines," humanly speaking. Personally, I think the margin by which success was secured was so narrow that none of the complex, interdependent factors could have been .spared, and that, as Admiral Sampson said after the battle of Santiago: "There is glory, enough for all." But if any one human factor can be said to have been absolutely indispensable, I think all will agree that it was the engineer. The engineer, as a rule, is a modest fellow, so modest in fact and so averse to publicity of any kind that, referring to him as a class, he was hardly occupying the place he should in public estimation before the war. By way of illustration, in the early history of a mine in Bisbee, the chief owner was also the proprietor of a saloon and spent most of his time there. When asked why he did not pay more attention to the mine, lie replied: "Oh! I can hire a boy to look after that; it takes a man to run this bar." Comparisons of the position and pay of engineers with other occupations are sometimes made to show that the engineer is not getting all that he should, considering the time of preparation and the qualifications required. Perhaps at least a part of the cause may be his aloofness from many of the practical affairs of everyday life. Whether he won the war or not, the part played by the engineer has certainly placed him on a sort of pedestal in the public estimation at present and it is very desirable to keep him there and maintain the position he has made for himself.

Jan 9, 1919

By F. Selig, A. S. Odeh

A second-order approximation to the exact solution of the diffusivity equation corresponding to the pressure build-up of a well producing at a variable rate is derived. This approximation is applicable when the well's shut-in time is larger than the total time elapsed since the well was first produced. The resulting equations are compact in form and easy to use. Thus, the need for Horner's' theoretically precise but rather laborious solution to the above problem is eliminated. In addition, these equations apply where the use of Horner's widely known approximate method is questionable. From a practical point of view, the reported method is best suited for analysis of drill-stem tests and short production tests conducted on new wells. INTRODUCTION The utility of drill-stem and short production tests in reservoir studies has long been recognized by the reservoir engineer. If interpreted correctly they could lead to a wealth of information upon which may depend the success or failure of reservoirs' analyses. Initial reservoir pressure and the average flow capacity are two quantities that are normally sought from a drill-stem and/or a short production test analysis. Pressures are the most valuable and useful data in reservoir engineering. Directly or indirectly, they enter into all phases of reservoir engineering calculations. Therefore, their accurate determination is of utmost importance. The flow capacity kh of the reservoir is indicative of its commercial capability. In addition, it can indicate the presence of a darnaged zone around the wellbore and, thus, the necessity for remedial measures. Of the several methods used to analyze drill-stem and short production tests, Horner's' method is by and large the most common. It applies to an infinite reservoir and or a limited reservoir where the effect of production has not been felt by the boundary. Horner's method makes use of the so-called "point-source" solution of the diffusivity equation. The point-source solution is approximated by a logarithmic function and the superposition theorem is utilized to give the familiar pressure build-up equation where is the shut-in time, q is in reservoir barrels per day and the rest of the symbols conform with AIME nomenclature. Eq. 1 was derived for a well which produced at a constant rate q from time zero to time t and was then shut in. In actuality, such a constant rate of production does not normally obtain. Therefore, a correction must be applied to Eq. 1 to account for the varying rates of production. Horner suggested two methods. The first, which results in a theoretically accurate solution, is rather lengthy and laborious and, thus, it is not suited for routine analysis. The second which has been termed a "good working approximation" is the one used by the majority of the reservoir engineers. In the second method, Eq. 1 is modified by simply introducing a corrected time t, and writing where q is the last established production rate prior to shut-in, and t, is obtained by dividing the total cumulative production by the last established rate. Horner's original paper does not give any indication that this method of correction is based on any theoretical justification. In addition, there is a question as to what constitutes the last established rate. In case of a drill-stem test some engineers use the average rate obtained by dividing the total fluid produced by the total flow time, while others calculate the average rate by dividing the total fluid produced by the last flow-period time. Obviously, different results obtain for the different flow rates used. Because of this, a simple method to the varying-rate case was developed which is theoretically sound and which defines clearly the flow rate and its associated time to be used in the calculations. The final equation arrived at is where q* and t* are a modified rate and time, respectively, and can be easily calculated. In addition, it is shown theoretically that Horner's approximate method, if used for a variable-rate case, gives the correct pressure but would not be expected to give the correct flow capacity. MATHEMATICAL ANALYSIS The general equation governing the flow of slightly compressible fluid in porous media may be written as The elementary solution to Eq. 4, representing an instantaneous withdrawal of Q units volume of fluid at the origin at t = 0, is known as the instantaneous sink

THE morning session on non-metallic minerals was opened briefly by the chairman, Oliver Bowles, giving the usual instructions and then turning immediately to the introduction of the speakers. "Min-ing and Preparation of the St. Peter Sandstone in' Arkansas" by D. D. Dunkin was first presented by W. M. Weigel, mining technologist for the Missouri Pacific R. R. The paper covered a discussion of the geology of the sandstone, correlating it with the sand-stones at Klondike, Mo., and at Ottawa, III. Its physical appearance, structural characteristics and thickness; the mining methods, blasting, loading, haulage and classification were taken up. A series of slides aided in clarifying the details. The discussion consisted of questioning Mr. Weigel on operating details. The second paper, "Geology and Mining of Diaspore and Flint Fire-Clays of Missouri," written by H. S. McQueen, geologist with the Missouri Bureau of Geology and Mines, and C. R. Forbes, professor of mining, Missouri School of Mines and Metallurgy, was presented by Mr. Forbes. It thoroughly covered the geology, stressing the peculiar sink formations in which all diaspore clay deposits of the region occur. The crudeness of the mining methods was mentioned and believed justifiable because of the small size of the indi-vidual deposits. It was stated that the diaspore and flint clay deposits of Missouri were confined to an area 60 mi. square and it was found in a survey that the average deposit had dimensions comparable to the fol-lowing: 100 ft. long, 75 ft. wide and 50 ft. deep. The largest deposit found was 800 ft. long. 500 ft. wide and 20 ft. deep. It is estimated that the known reserve of clays is from 750.000 to 1,500,000 tons. Mr. Forbes stressed the fact that in mining clays the major problem is entirely one of sorting. This is done under the supervision of a pit foreman trained to make this classification by eye. The mine-run clays are sepa-rated into diaspore clay ranging in alumina content from 70 to about 85 per cent, first grade Burly clay 00 to 70 per cent, and Flint clay 52 to 60 per cent. Discussion of the paper consisted in questioning Pro-fessor Forbes on labor. cost, haulage, drilling, and geology.

Jan 3, 1928

By O. W. Bilharz

Acid mine-water drainage is a serious problem with many mines in the Tri-State zinc and lead mining district. Particularly is this true when large volumes must be considercd in unwatering old mines that have refilled with water which has dissolved the products of oxidation and has become chalybeate in character. The experiences discussed in this paper have to do specifically with the unwatering of a comparatively small area west of the town of Baxter Springs, Kans., where the pumping job was complicated by water of this type and where the extremely high sulphate content particularly effected that phase of mine drainage having to do with stream pollution. Location, Geology and History The Baxter Springs area of the Tri-State mining field is situated just west of the town of Baxter Springs and is a northeasterly extension of the main mineralized zones of the Oklahoma part of the district (Fig I). The mining area is traversed with well defined shear zones which provide easy circulation of ground waters and the ore bodies are found along these shear zones as localized enrichments wherever the structural conditions are favorable (Fig 2). The ore-bearing strata is Mississippian with an overlain capping of shale of Penn- sylvanian age. This shale strata carries much pyrite and marcasite at its base and undoubtedly was a contributing factor to the subsequent high iron content of the water. The area originally contained a sulphide water which discharged as an artesian flow in springs within the town and gave Baxter Springs its name. These springs were famed for many years for their mineral water. This original sulphide water was first removed about 1917 and active mining was carried on west of the town during subsequent high metal price periods. Many small mines were opened, with each localized enrichment becoming a separate mine. During the depression mining ceased and all mines in the west Baxter area were allowed to flood. No serious effort was made to again unwater until higher prices caused from the demand for metal for World War II once more focused attention 011 this part of the field. Original Mining Results in Oxidation As plans for unwatering progressed, it soon developed that the mine-water pools had become strongly acid in character and carried large amounts of sulphates in solution. This occurred in the following way. When the original sulphide water was removed, shafts sunk, and mining carried on over a number of years, ferrous sulphate was formed by the spontaneous oxidation of the pyrite beds in contact with air admitted through churn-drill holes and mine openillgs. These products of oxidation can be seen today in the old mines of the district as crusts of crystalline sulphates

Jan 1, 1949

By B. B. Sandiford

It has been known for many years that the efficiency of a water flood can be improved by lowering the water-oil mobility ratio in the system. Such a change leads to better sweep efficiency and also to more efficient oil displacement in the swept zone. Data from our laboratory water-flood tests of both small cores and long sand packs are presented which show that water mobility can be reduced and oil recovery increased by the addition of certain polymer solutions to flood water. The reduction in mobility, in many cases, is greater than would be expected from conventional viscosity measurements. These solutions, however, do not cause significant reductions in oil mobility. The over-all effect of these mobility changes is increased waterflood oil recovery. Encouraged by results of our laboratory work, we expanded our study to include pilot field tests of floods with such solutions. One such test, made in the West Cat Canyon field, Santa Barbara County, Calif., is described in detail in this paper. Three other field tests are also discussed. INTRODUCTION Oil production from most reservoirs following primary depletion and/or water flooding is often less than 50 per cent of the original oil in place. Heavy oil reservoirs seldom yield over 15 per cent of their original oil. With new reservoirs becoming harder to find, the improvement of oil recovery efficiency is one of our very important problems. We describe here some of our attempts to increase the efficiency of oil displacement by adding a water-soluble polymer, partially hydrolyzed polyacrylamide, to flood water. This technique will be termed "polymer solution flooding". The concept of using high-viscosity water to increase the efficiency of water flooding is not new. In 1944 Detling (Shell Development Co.) obtained a patent covering the use of several additives for viscous water flooding.' His objective was to improve water-oil mobility ratios by increasing the viscosity of the flood water. Other patents2-27 have been granted covering specific water-SO~LIble polymers or specific conditions of viscous water flooding. Barnes'" described his laboratory model study of the injection of a viscous water slug into a reservoir which had been partially invaded by bottom water. He concluded that, for this type of reservoir, "the cost of viscous water should not exceed a few cents per barrel for viscous water slug injection to be economically feasible" Our studies have led us to a somewhat different conclusion in a number of cases where hydrolyzed polyacrylamide solutions have been injected into reservoir models or actual reservoirs. Possible reasons for this difference are discussed in this paper. Our studies have shown that polymer solutions may lead to an increase in oil recovery over that from an ordinary water flood by (1) improving sweep efficiency, (2) improving microscopic displacement efficiency, or (3) a combination of these mechanisms. In the work of Barnes, only the benefit of improved sweep efficiency was considered. Also, our work has shown that there are marked differences in the effectiveness of different water-soluble polymers as flood water additives. Partially hydrolyzed polyacrylamide is better than many other water-soluble polymers we have tested because, even in very low concentrations, it can lead to increased oil recovery. This is an important advantage when either a dilute polymer solution is injected continuously or a relatively concentrated slug is injected followed by water. In the latter case! portions of the slug become diluted and function in the formation as very dilute solutions. As dilution takes place the effective slug size will increase which, in turn, will reduce the cost per barrel of the effective flooding medium. The reason that partially hydrolyzed polyacrylamide solutions are more efficient at low concentrations than certain other polymer solutions of equivalent viscosity (when measured in conventional viscometers) is not fully understood. We do know that the shapes and sizes of macro-molecules dissolved or suspended in liquids influence the flow properties of their solutions or suspensions. Solutions of partially hydrolyzed polyacrylamide cause greater reductions in water mobility than would be expected from conventional viscosity measurements. LABORATORY STUDIES Laboratory water floods were run in linear and radial systems with different water-soluble polymers and under varying conditions of flow. including reservoir conditions of temperature, pressure and fluid composition. Some of these runs are considered in this section. OIL DISPLACEMENT IN LINEAR MODELS In this group of runs the sweep efficiency approached 100 per cent because the linear sand packs used were as nearly uniform as possible. Results reflect primarily the micro-scopic displacement efficiencies. The laboratory models were unconsolidat-ed sand packs the lengths of which varied from about 4 in, to 40 ft. Further information on the flow models used is listed in Table 1. Using conventional procedures, water floods were run on sand packs containing either refined or crude oil at restored state. Frequently, a repeat run, similar to the first, was made as a check. Then a third run was made on the restored-state model using either polymer solution or a combination of polymer solution (slug) and water. Details of these runs are also reported in Table 1. In Figs. 1 and 2 results of two different groups of runs are shown in which the oil used was a 62-cp refined oil and the flooding medium

Jan 1, 1965

By Charles H. Fulton

CHARLES H. FULTON, chairman, presided at the first session of the Mineral Industry Education Division on Wednesday morning. Reporting for the program committee, Edward Steidle, its chairman, pointed out that its function was not to arrange programs for meetings but to plan a program for the Division to follow in the development of its activities. This was appropriately followed by presentation and discussion of his paper, "Basic Trends in Mineral Industries Education," which, being available in printed form, was only presented in oral abstract. Jay A. Carpenter submitted interesting written discussion that was read, in his absence, by A. M. Smith. Most of the morning was devoted to the discussion of the paper, which was too extensive and ranged too widely to attempt to report in much detail. H. T. Mann, H. P. Hammond, Cadwallader Evans, C. H. Fulton, T. T. Read, D. F. McFarland and P. B. Bucky joined in the discussion, Mr. Hammond making a plea for more unification in mineral industry education, saying that in the study he made for the Society for Promotion of Engineering Education about 35 different curricula preparatory to work in the mineral industry were discovered to exist. He felt that most of the needs of the mining industry could he met by men who had had four years of engineering training of good enough basic quality to permit them to advance along special lines. However, there was apparently a growing demand, as reflected by the increasing number of candidates for the Master's degree in engineering, for men with more thorough training in the fundamentals.

Jan 1, 1933

By C. C. Griggs

From its inception, a limestone quarry or mine should be under the direction of a capable engineer. Before it becomes a reality, he should outlinc the future results, plan the most economical methods for moving the materials and the most efficient equipment, and pilot the undertaking along the narrow pathway of success, avoiding the pitfalls of uneconomical production and the precipitous walls of scanty profits. Inspection of successful limestone properties shows that all have had difficult engineering problems, the solution of which have required keen engineering ability. In approaching a subject of this nature, it is logical to follow the progress of the limestone operation from its inception to the end, as reflecting the engineering required. There are four major divisions: Investigation, equipment, development, and operation. Investigation On the reliability of the engineer's estimates and the soundness of his judgment depend the success or failure of the enterprise. When one visits a prosperous concern, realizes that the limestone is of a constant chemical composition, sees the mechanical devices installed, and watches the output leave the plant in trains of railroad cars or fleets of vessels, he may overlook the fact that in the remote past this great creation was born in some man's brain and evolved through competent engineering. Many factors must be considered before a promoter could procure the money necessary to launch such an enterprise, for a conservative banker will only recommend a successful producer while the promoter must provide funds on his own and his engineer's judgment. An engineering investigation must be made preliminary to expenditure for actual operation, which, for a limestone deposit, would' naturally embrace such subjects as : ' Readily available. 1. Tonnage available........ Possibly available. Chemical analysis.

Jan 1, 1925

By R. J. Weege, A. W. Schillinger

Conventional underground mapping methods and diamond drilling are being applied in a study to determine the nature of the copper ore occurrences near the footwall of the Osceola lava flow top, commonly referred to as the Osceola Amygdaloid. The work to date suggests that structures formed by relatively impermeable barriers, created by flowage and injection of still-molten lava from the interior of the flow into the solidified, brecciated crust, acted as the ore receptacles. Ascending hydrothermal fluids traveling near the footwall contact were trapped and confined in these barriers which retarded the direct upward movement of the ore fluids and caused deposition of copper. Oreshoots located near the footwall appear to have been formed spatially independently from the hanging-wall oreshoots by fluids traveling simultaneously, but along different channelways. The barrier concept, as advanced by earlier writers to explain the concentration of the ore-bearing fluids into broad shoots constituting entire ore bodies, is found to be equally as applicable for the localization of smaller oreshoots within the Osceola ore body. Recently, the Calumet Division of Calumet and Hecla, Inc. completed the unwatering of the old mine workings on the Osceola amygdaloid. Two shafts were subsequently reactivated and mining commenced on the Osceola lode after an idle period of over 20 years. Early in 1961, the Calumet and Hecla Geological Dept. was assigned the task of locating additional reserves. Accordingly, an intensive mapping and underground diamond drilling program was initiated. Except for a very few years following the first mining on the amygdaloid, the Osceola lode had never been a high grade producer. It was, therefore, recognized from the onset that a concentrated effort would have to be made by the mining, milling, and geological departments to insure success of the project. Company reports contained many references to ore that had been located near the footwall of the Osceola amygdaloid. Information concerning the grade of this ore was meager, but it was known that at least some was very rich. In contrast to ore that occurred near the hanging-wall, however, the footwall copper did not appear to have a systematic distribution and a large amount of poor rock had to be removed in developing this ore. This, of course, resulted in high development costs and discouraged any extensive mining of footwall ore. The possibility of more continuity than had previously been suspected was recognized by other workers, in particular Dr. T. M. Broderick, formerly Chief Geologist of Calumet and Hecla, who suggested attempts be made on a trial basis to follow the footwall contact with the main development drift. As most mining was done on the Osceola lode before a geological department had been established by the company, and almost all of these openings are now caved, very little information concerning the geology of footwall ore was available. It was, therefore, decided that the first step in the exploration program would be to become familiar with footwall ore occurrences by mapping the geology as the openings were driven. It was possible that a mapping program would reveal the features that controlled the localization of the ore. Furthermore, if it could be shown that footwall ore was more continuous, or if its distribution was more systematic than generally believed, it would be possible to produce a high grade ore that could be blended with the lower grade hanging-wall ore. In connection with the geological program, the Michigan College of Mining and Technology Geophysical Dept. under the direction of Professor Lloyal Bacon, is making a geophysical study of the problems of locating footwall ore by electrical methods. GENERAL GEOLOGY OF MICHIGAN NATIVE COPPER DEPOSITS The native copper deposits of Michigan are located in Keweenaw, Houghton, and Ontonagon Counties. The host rocks are Keweenawan in age and are comprised of interbedded sediments and lava flows which form a belt two to four miles wide and over one hundred miles long. These rocks form part of the south limb

Jan 1, 1962

By E. R. Russell, N. E. Richards

The current ejyiciency of aluminum cells was derived from the metal produced over a period of time and the theoretical faradaic yield. The difference in the actual amount of aluminum in the cathode at the beginning and end of the period must be determined. The weight of aluminum in the cathode was calculated from the dilution of an added quantity of impurity metal. Use of multiple indicator metals, copper, manganese, and titanium, demonstrated that the weight of aluminum in cells can be determined to within 1 pct with routine but careful chemical analyses. Over intervals of the order of 30 days, current efficiencies reliable to within 1 pct can be obtained. INVESTIGATIONS beginning with those of Pearson and waddington ,' through the most recent published work of Georgievskii,9-11 illustrate the direct relationship between the composition of the anode gas and the applicability of analysis of anode gases to the control of alumina reduction cells. McMinn12 noted the lack of an independent method for measuring cell production efficiency over the short term. There is no doubt that changes in the current efficiency are immediately reflected in the composition of anode gases. However, the accuracy of faradaic yields calculated from gas analyses depends upon the degree of interaction between primary anode gas and Carbon.6 A conventional industrial practice of obtaining long-term current efficiency for production units from mass balances and quantity of electricity is generally insensitive to the impact of planned control of any one or more of the influential reduction cell parameters such as temperature, alumina concentration, and mean interelectrode distance. Consequently, there is a real need in the aluminum industry for a procedure to obtain the absolute cell current efficiency over a short term—10 to 30 days—both for the calibration of values obtained from gas analysis6 and for evaluating the effect of controlling specific parameters in the reduction process. The amount of aluminum produced may be determined by considering the cathode pool as a reduction of an impurity metal in aluminum. Analyses over a period will show a decreasing concentration of the impurity due to the accumulation of aluminum solvent. The increase in aluminum inferred from analyses is the amount produced by the cell during the period. Combining weights of the cell aluminum in the cathode at the beginning and end of a specific period, weights of aluminum tapped and the quantity of electricity passed during the interval will yield the current efficiency. Smart,I3 Lange;4 Rempel,15 Beletskii and Mashovets,16 and winkhaus17 have used dilution techniques to determine aluminum inventory in alumina reduction cells. A technique for determining the weight of aluminum in production cells by addition of small amounts of copper to the aluminum cathode was described by smart.13 The precision in values of the aluminum reservoir through dilution of copper in the cathode ranged from about 1 to 3 pct depending upon the quantity of copper added in the range 0.2 to 0.01 wt pct, respectively. Because the method appears so direct and apparently simple, one would not anticipate difficulties in application to industrial cells. The objective of this study was to resolve this problem associated with the trace metal dilution technique for determining the amount of aluminum in a cell. The approach in evaluating trace metal dilution as a basic factor in determining the weight of aluminum in the cell reservoir, and the absolute current efficiency of the Hall-Heroult cell, was to dilute more than one trace metal in the aluminum cathode so that we could discriminate among complications arising from physical mixing, the possibility of separation of intermetallic compounds, loss of the added elements, and chemical detection. EXPERIMENTAL METHODS These experiments are not complex but require standardized procedures. The technique involves addition of the trace metals to the cathode, knowing when these metals are homogeneously distributed in the liquid cathode, timing of the sampling, employing accurate and precise analytical methods, using reliable procedures for monitoring the amount of electricity passed through the cell, and accurate weighing of aluminum removed from the cell during the particular period. More accurate results might be obtained if the increment in concentration of the added indicator metals were of the order of 0.1 to 0.2 wt pct. The method must be applicable to production units and, hence, the contamination of the aluminum minimized. For this reason, the concentration of trace metals in the cathode was kept below 0.07 wt pct and generally at 0.04 wt pct level. Trace quantities of copper, manganese, titanium, and silicon are already present in virgin aluminum and are suitable as additives from electrochemical and analytical points of view. Concentration of silicon is quite dependent upon the characteristics of the raw materials and was not used extensively in this work. Chemical Analyses. All instrumental analyses require calibration against an absolute technique such as a gravimetric, volumetric, or spectrophotometric method which represents the ultimate in sensitivity, precision, and accuracy. On review, the best methods for copper appeared to be optical absorption without

Jan 1, 1969

By A. B. Kinzel

SINCE the exposition of the behavior of certain iron alloys by Sykes1 involving the existence of an austenite loop and the discovery of such a loop in the chrome iron system by Bain,2 there has been much conjecture both on his part and on the part of metallurgists in general as to the exact shape and location of this loop. In previous work commercial steel has been used and the microscope has been employed to locate the critical points so that the position of the loop has been quite approximate. Numerous attempts have been made to measure the critical points of the carbon-free alloys but all of these for one reason or another have failed. A satisfactory method for studying these phenomena is presented here. MATERIAL The first difficulty in this study was to obtain pure chromium-iron alloys. This has been overcome by melting in a vacuum electrolytic Eton and chromium analyzing 99.84 Cr, Fe and C. A pure magnesite crucible was used and the melt allowed to solidify in the crucible. A typical analysis is chromium, 10.10 per cent., carbon, 0.006 per cent., silicon and manganese nil. To overcome the problem presented by segregation, ingots were made into wire 0.04 in, in diameter. This was accomplished by hand-forging the ingots into rods, using an oxyhydrogen flame for heating, in order to avoid carbon. Subsequently the rods were swaged to wire, the heating being carried out in hydrogen. Thus local segregation was eliminated although differences in analysis between portions 50 ft. apart were noted. An electric-resistance method was first tried to determine the critical points, but due to the physical defects in the wire this failed. Bain had previously shown the presence or absence of critical points in a qualitative way by observing the sag in a catenary. The author has devised the following method which gives an accurate determination of the critical points from expansion-temperature curves of suspended wire, a special telescopic dilatometer being used for the purpose.

Jan 1, 1928