Search Documents

By C. E. Lawall

ONE of the most important developments in the coal industry during 1940 was the continued uptrend in the production of bituminous coal. Estimated production for the year is 450,000,000 tons, with an additional production of anthracite of 50,000,000 tons making a total of approximately 500,000,000 tons. This is an increase of 12.5 per cent over 1939. Despite an estimated decrease of about 3.5 per cent in anthracite production, all of the major coal-producing states had increases in production for 9140. The national defense program, with the consequent increase in industrial activity, undoubtedly had an important effect on the increased demand for coal.

Jan 1, 1941

By W. L. Zeigler

During the middle 1880's, shortly after the discovery of silver-lead ores in the Coeur d'Alene district of northern Idaho, it became apparent that concentration of the ores would be necessary to obtain a profitable product. Too much siliceous material was present for direct smelting, and the majority of the ores found at depth were too low in metallic content for economic smelting processes at the time. As the ores occurred in quartzite shear zones with siderite and quartz gangue, a large quantity of waste material was present in all the mines. As the galena was not finely disseminated, this made possible relatively good extraction of the argentiferous galena by coarse concentration. The first concentrators consisted mainly of coarse crushing, screening and jigging, principally by Harz jigs, the slimes being treated on buddles. Later Wilfley tables took the place of sand jigs and vanners superseded the buddles. Because of the marketing conditions, no attempt was made until 1900 to effect a recovery on the zinc minerals present, which were found associated in varying amounts with the galena. All through this period, the greater part of the production was obtained from mines containing ore assaying high in lead and low in zinc. Parts of some ore bodies would be reversed in this respect, so that ores high in zinc were left intact. During the decade after 1910, several important mines, The Success and The Interstate Callahan, containing ores high in zinc, were put into operation and were a material aid in the needed zinc production during World War I. Gravity concentration by jigs and tables was used during this period, with bulk flotation increasing in popularity for the treatment of the fine material that had already been treated by ordinary slime concentrating machinery. No extra fine grinding for flotation concentration was thought profitable at the time. Tailings Discharged into Streams From the start of mining and milling operations in this district until 1904, no attempt was made by the various mills in the upper district to impound or stack their tailings. They discharged them directly into the adjacent creeks or streams, to be carried away by high water. The Bunker Hill and Sullivan and the Last Chance mines, both in the relatively flat valley of the district, stacked huge piles of the coarse jig tailings on the near-by river bottom. Rain and snowfall are heavy in the Coeur d'Alene district, as it is on the heavily timbered Pacific slope of the Bitter Root Mountains. A heavy runoff occurs every spring and there is an occasional flood of disastrous proportions when warm "Chinook" winds accompanied by rain

Jan 1, 1949

By Edmund Kirby

This meeting marks the point at which the long-standing dissatisfaction with the mineral-land laves, the innumerable protests against them, and the many isolated efforts to obtain relief, have developed into a general movement for the: revision. That part of the mining industry which is affected by these laws has three general organizations to speak for it: the American Institute of Mining Engineers, Mining and Metallurgical Society of America, and the American "A Mining Congress: all of which are represented in this meeting. In the series of able and thoughtful presented here, prominent men have discussed the evils of the present laws aid some of the reforms which should be made in them. We all appreciate fully the ultimate value of these studies; but we are also painfully aware of the fact that discussion of this kind has been going on for a quarter of a century without any other effect than a steady increase in the mass of printed records stored on library shelves. In order to get any practical result we must induce an indifferent government at Washington to act, and to do this we must unite in pushing some practical plan whereby it may act in a simple and effective way and with the least possible amount of criticism or opposition. The actual question before us is not whether the mining laws are bad; for their evils and absurdities are not only beyond discussion but also beyond the resources of a temperate and dignified vocabulary. It is not what particular changes ought to be made; for it is premature to make specific recommendations until there is some one to listen to them. Moreover, we all know that there are wisdom and experience enough available, and awaiting that time, for the creation of a code which would be a model to the mining world. The practical question now is, how to obtain the revision; and since the American Mining Congress has of late restricted its attention to this phase of the problem I wish as one of its representatives here to present its views upon the matter.

Jan 6, 1914

By J. B. Dilworth

OUTCROPS of coal have bees discovered is many localities is the Philippine archipelago, and practically all of the larger islands contain deposits of this mineral. Very little prospecting has been done to determine the value of the various coal-bearing areas, but so far as known, the largest and most promising fields are found : (1) is northern Cebu; (2) is the small island of Batan, a part of the province of Albay is southeasten Luzon; (3) is the somewhat larger island of Polillo, off the east coast of Luzon, and (4) is southern Mindoro, sear the small coast tows of Bulalacao. Northern Panay, south-central Cebu, and various localities is southern Luzon, Masbate, Negros, and Mindanao also afford evidences of the existence of coal-beds, the extent and value of which have not yet bees proved. The general position of these islands and districts is shows on the map of a portion of the Philippine Islands, Fig. 1. Some of these coal-fields have been known for many years (coal was discovered is Cebu 1827 and is Batas is 1842),1 and several futile attempts were made by the Spaniards to operate mines is these districts. But owing to many circumstances, chief among which were indifferent management, the political unrest of the islands, natural difficulties of transportation, and those inherent in the mining of steeply-inclined and somewhat irregular seams, no considerable output was ever obtained from any of these mines, and the fuel required is the many departments of industrial and political life has continued to be drawn largely from Australia and Japan. These conditions exist to a great degree at present, and though much interest is the coal-deposits of the Philippines

Jan 1, 1909

By Herbert Hoover

NO ONE could fail to be gratified to receive so profound an approbation in his calling from the members of one's own profession. To have re-ceived this distinction from men, many of whom have been professional associates and friends over more than a quarter of a century, warrants a pride. and satisfac-tion that could come from no other source. It has often been said that men are really known only to their brothers in labor and in profession. The long friendship I have received from Mr. Saunders and the distinguished service that he has contributed to the mining industry add to my appre-ciation of this event. Mr. Kelley's remarks bring my mind easily to the beginning of that period of great advance in the engineering, profession of forty years ago. Three great forces contributed to the development of the profession. The first was the era of intense development of minerals, metallurgy; and transportation in our great West. It greatly stimulated invention; it made a demand for training and skill on the part of our engineers. The pressure of national development advanced our American practice beyond the rest of the world. Moreover, the skill of our engineers of that period owes a great debt to American educators. The leaders of our universities were the first of all the educators of the world to recognize that upon them rested the responsibility to provide fundamental train-ing in, the application of science to engineering under the broadening influence and cultivation of university life. They were the first to realize that engineering must be transformed into a profession in the highest sense, not only in the training and character but that the essential quality of a profession is the instillation of ethics. That implies not alone the job but the responsibility of the community for the job. Our uni-versities poured into our development a great stream of men with this background and training. A third distinction that grew in American engineering was the transformation from solely a technical profession to a profession of administrators-the business manager with technical training.

Jan 3, 1928

SINCE I told you in the preceding chapter how the potter's art is followed in practice, now in this following one I wish to tell you how mortar* and bricks are made, and how and to what purpose they were discovered, although I know you will answer that you know it, inasmuch as it is an art known not only to skillful men but also to the unskilled ones by whom it is practiced, and that bricks and mortar were made and always will be made for the purpose of building. This I admit, but probably everyone does not know it as you do, and you perhaps, do not know its beginnings, although I remember having told you of them. Wishing to repeat it better now I shall begin with long ago, so that both you and I may be better satisfied. Therefore I tell you that you should know that all the arts that men practice in the world have been learned by them either through the process of reasoning from the principles of natural phenomena, from the actions of animals, by chance, or when forced either by some necessity or

Jan 1, 1942

By Frank Firmstone

The material described below was made at Furnace No. 2, Longdale, Va., Oct. 28, 1907, during a sudden derangement of working, in the course of which the furnace became entirely bridged over and for some time no solid material whatever descended into the hearth. This caused the hearth to become so completely emptied that, at the tuyere-level, a pricker put in at one tuyere could be seen by looking in at the opposite one. The tap-hole was opened and the iron got out with some difficulty. It ran sluggishly, throwing many sparks, but was not too thick to run into the chill-molds. Naturally, the product was assumed to be white iron, which is almost always produced under similar circumstances; but on removal front the molds it proved to be very strong and tough, although full of blow-holes. Most of these blow-holes bad bright, unoxidized walls. The iron could be drilled by using a "special steel" drill, the drillings curling up similarly to those of steel. An analysis by P. W. Shimer of this unusual product gave: Si, 0.019; P, 0.228; S, 0,39; Mn, 0.042; C, 2.366; and graphite, 0:000 per cent. A cast of iron made just before the disturbance contained P, 0.98, and Mn, 1 per cent. The peculiar product seems to have been decarburized in the hearth and, at the same time, to have lost much phosphorus and manganese, either by the action of the blast in the empty hearth, or, more probably, by. contact with the cinder rich in iron which was formed at the time. Unfortunately, no specimen of the cinder was preserved, so its composition cannot be given. It seems very remarkable that, with the furnace in bad condition, the temperature should be high enough to keep such

Sep 1, 1908

By C. G. Albert

The clay particles of 2 microns or less required for modern paper coating are predominantly flat plates, lying smoothly on the sheet and producing a high gloss. Operating speeds of today's coating machines necessitate a clay composition of 60 and sometimes 70 pct solids as against the 35 to 40 pct required in the past. Since clays in suspension may solidify in flow, only those of intrinsically low viscosity can be used as high coating solids. THE literature of paper technology contains a number of articles having reference to developments in the field of coating and filler clays for use in paper manufacture. Much of this information has not been included in mining publications and has therefore not been readily available to all in the mineral industry. Recent developments in this field, including spray drying of clays, are presented here. U. S. Bureau of Mines figures for 1952 indicate that the paper industry consumes more than 50 pct of all kaolin produced and sold in the U. S. As most of the kaolin used by the industry comes from Georgia producers, the fraction of their output destined for paper use is thus appreciably higher than 50 pct. Small wonder that the kaolin industry, especially in Georgia, is highly sensitive to the quality requirements of paper mills and must respond promptly to technological developments in paper manufacturing. The paper industry itself is not the ultimate consumer. For the greater portion of the clay the end product is the printed page, and the demands of printing and publishing have sparked some of the technological advances in paper making which have, in turn, brought about methods employed in the kaolin industry. As compared with the product of 20 or 25 years ago, one of the most striking characteristics of the graphic arts today is the mass production of quality printing of fine pictorial work, much of it in full color. During this time periodicals with printing standards close to those of yesterday's slick-paper publications that were printed on a slow schedule and for a limited circulation have grown to the point where they go out to many millions of readers, often at weekly intervals. The complexity of technological improvements brought about by this increased circulation is probably not appreciated even by technical people, unless they have had reasonably close contact with the industry. The advance has come about through developments not only in the art of printing, but also in the field of paper making and even at the level of clay mining and processing. The smoothness required for faithful reproduction of the kind of printed matter under consideration is attained with a clay-coated paper. Since the distribution expense of the publication will depend to a great extent on its weight, the paper used must not be too heavy. This means a lower basis weight than was normal for conventional clay-coated papers some 25 years ago. And for this mass production market it becomes necessary to provide a paper having these and all the other required characteristics at a very moderate price—not the premium price conventional clay-coated papers formerly demanded. This challenge has been met by a new method of producing coated paper. In the past, application of clay coating to paper was a conversion operation, performed separately from the making of the base sheet. The newer development is called machine coating. Here application of the coating is an integral step in a continuous process by which wood pulp, clay, and other ingredients are manufactured into a sheet of coated paper. Many more problems are involved in this procedural change than are apparent at a casual glance. The coating operation, for example, must function at much higher linear speed than could be obtained with coating mechanisms previously employed. The application machinery developed to meet this requirement necessitated changes in composition of the coating color.* This created new requirements, summarized below, for the clay employed as coating pigment. In addition to smoothness, a relatively glossy printing surface is needed, and to a large measure it is the function of the coating clay to make possible the development of both these surface characteristics. Traditionally, pigments such as satin-white, prepared by reacting lime with paper-makers' alum, were used to assist in producing a high finish. However, economic considerations and others preclude large-scale use of such material in the new processes. In the 1930's Maloney' discovered that a certain particle size fraction of kaolin, consisting

Jan 1, 1956

By S. Lipson, H. W. Antes, H. Rosenthal

A study was made of the effect of ingot structure on the strength and ductility of high-strength wrought-aluminum alloys. It was found that a fine-cast structure facilitated complete homogenization which, in turn, resulted in significant increases in ductility and strength. A completely homogenized 7075-T6 alloy developed tensile properties of 85,000 psi UTS, 75,000 psi YS, with 40 pct RA. Completely homogenized 7001-T6 alloy tensile properties were 102,000 psi UTS, 99,000 psi YS, with 19 pct Ra. A method was devised for making small ingots having secondary dendrite arm spacing of less than 10 u. This method involved multiple-pass arc melting of commercial rolled plate with a tungsten electvode. This material could be completely homogenized after 3 hr at 900°F; homogenization of the original plate material was not complete after 120 hv at 900°F. Degree of homogeneity was determined by use of metallographic and electron-microprobe analyses. The electron-micro-probe study also showed the preferential segregation of solutes in the microstructure. HIGH-strength aluminum alloys, such as those of the 7000 series, usually freeze by the formation and growth of dendrites. The dendrite arm spacing (DAS) depends on the rate of solidification.' Commercial ingots are usually direct chill-cast to promote more rapid solidification, but, due to the large mass of the ingot, localized solidification times are long and a large DAS results. During solidification, solute elements are rejected by the solid as it forms, causing enrichment of the liquid and ultimately solute-rich interdendritic regions. In order to attain a homogeneous ingot, the segregated solutes must diffuse across the dendrite arms. The larger the DM, the longer the time for complete homogenization. In the case of commercial ingots, the DAS is so large that the time for complete homogenization is prohibitively long and, therefore, second phases or compounds are always present. These un-dissolved phases are carried over to the wrought material during processing, resulting in an impairment of strength and ductility. In addition, the mechanical fibering of the undissolved second phases or compounds during working results in mechanical property anisotropy. If complete homogenization could be attained, higher ductility could be expected. The realization of higher ductility at current strength levels is a desirable objective; however, if higher-strength alloys were wanted, it might be possible to sacrifice some of this ductility by adding more solute elements and produce even higher-strength alloys than are currently available. Further, if complete homogenization leads to more efficient utilization of solute elements, then more dilute alloys should have relatively high strengths with very high ductility. In all instances, it would be expected that the degree of mechanical property anisotropy due to mechanical fibering would be reduced. Therefore, it was the purpose of this investigation to produce cast structures that would facilitate homogenization and to determine the effect of homogenization on the properties of high-strength, wrought-aluminum alloys. MATERIAL CLASSIFICATION Commercial Alloys. In order to illustrate the non-homogeneous condition that exists in commercial high-strength, wrought-aluminum alloys, typical micro-structures of 7001, 7075, and 7178 are shown in Fig. 1. The chemical compositional specifications of these alloys are given in Table I. It can be seen in Fig. 1 that a considerable amount of undissolved second-phase material is present in each of these alloys. The solute elements associated with the undissolved phases were identified by electron microanalyses. Back-scattered electron images and characteristic X-ray images of the three commercial alloys are shown in Figs. 2, 3, and 4. These data indicate that the second phases are regions of high copper and high iron-copper concentrations. The second-phase material also was analyzed for magnesium, zinc, manganese, chromium, and silicon, but no significant enrichment above that of the matrix was found. Therefore, the problem of homogenization resolved itself into one of dissolving the copper-rich and the iron-copper-rich second phases. In order to accomplish this objective, two approaches were made. The first was to reduce the iron as low as possible since this element has a maximum solid solubility of 0.03 pct in aluminum. The second was to produce cast structures with finer DAS to facilitate dissolving the second phases. Commercially Produced High-Purity Alloys. A special high-purity, 2000-lb ingot of 7075 alloy was made by a commercial producer. This alloy contained the following weight percentages of solutes: 5.63 Zn, 2.48 Mg, 1.49 Cu, and 0.21 Cr. All other elements combined were less than 0.02 pct by wt including iron and silicon at less than 0.01 pct each. The ingot was cast and processed into rolled plate using standard commercial techniques. Microstructures of standard commercial 7075 and the special high-purity 7075 are shown in Fig. 5. It can be seen from this figure that the high-purity alloy has less undissolved second-phase material, but a significant amount was still present. The second phase in the high-purity material did not contain iron but it was found to be enriched with copper. The slight effects of the increased purity and de-

Jan 1, 1968

By S. R. Zimmerley, S. F. Ravitz

High-grade cobalt concentrates were produced from the complex Blackbird ore with very good recovery in continuous pilot-plant operations in which a low-grade bulk cobaltite-pyrite flotation concentrate was roasted in a multiple-hearth furnace to oxidize the pyrite selectively. The cobaltite was floated from the resulting calcine.

Jan 1, 1950

By J. W. Graham

For many years the author has been cognizant of the difficulty encountered by some in treating with the water influx formulas for unsteady-state fluid flow as pertain to the material balance equation. This has particularly applied in establishing reservoir performance and identifying reservoir pressure, which to the practicing engineer has entailed a trial-and-error procedure, and for others has necessitated resorting to computing devices and reiteration processes. In retrospect this difficulty stems from the fact that reservoir pressure in the material balance formulas, as well as associated with the water influx equations, is an inexplicit term, and the work reported in the past is irrefutable. However, what will be presented in this paper is another approach to the problem, whereby the entire material balance equation will be treated by the Laplace transformation, and reservoir pressure which hereto has been inexplicit, can now be isolated by mathematical procedure to relate that parameter with all the factors contributing to its change. This is the simplification entailed, that treats first with an undersaturated oil reservoir as an integrated effect from the inception of production. The second phase pertains to saturated oil reservoirs that encompass a survey traverse. Although both methods of approach are necessarily different in aspect, the most interesting fact is that the mathematics so deduced are identical. Both the linear and radial water-drive systems are incorporated. for which an illustrated factual example is offered for the latter, treating with a saturated oil reservoir. INTRODUCTIO N What is performed in this work is the simplification of an involved computation by advanced analysis. Although such may be construed as a contradiction when one treats with higher mathematics; nevertheless, when direction is given to such an undertaking the results car. be most revealing. Likewise, it is to be mentioned that the bases for these mathematics have been developed on the expediency of the occasion. This is not to be inferred as a qualification of this work, but rather the demands frequently placed upon the author in his private prac- tice in meeting a time limit. A situation, instead of being fraught with hazards, often has given emphasis to creative thought. What will be entailed in this work is the simplification of the material balance formulas by the Laplace Transformation., Although this reveals entirely new horizons that will be given expression in a forthcoming tract, it suffices in the present instance to limit our attention to this phase of the development that treats both with an undersaturated and saturated oil reservoir. To orient the reader's thoughts as to what is involved in this simplification is the recognition that reservoir pressure, as such, is an inexplicit term in the material balance equation. This is the independent parameter that defines the total history of performance in the author's' unsteady-state water influx formulas, as well as the basis for the physical dependency of fluid behavior within the formation as prescribed in the Schil-thuis' material balance equation. Therefore, to isolate reservoir pressure, which is the most essential factor in any reservoir study, is rather a cumbersome procedure entailing either a trial-and-error calculation for the engineer; or as some prefer, a reiteration process performed on a computing device. However, once such an equation can be transcribed as a Laplace transformation, this inexplicitness so expressed can be alleviated to identify reservoir pressure as an explicit function of all the factors contributing to its change. This is the simplification encompassed, that will treat first with an undersaturated oil reservoir as an integrated effect from the inception of production, and secondly, with a saturated oil reservoir as a survey traverse. Although the two approaches are necessarily different because of the uhvsics involved. it is an interesting commentary that the mathematics are identical, showing the interdependency of the two methods. In order to acquaint the reader with this development, the simplest case will be treated first; namely, an under-saturated oil reservoir subject to a linear water drive. However, what may be construed for this example as an idealistic case is actually a most practical application in certain parts of the world, where the size of the fields are so large that radial water-drive approaches the configuration of a linear drive. Further, to avoid the repetition of much symbolism, frequent references will be made to the work of the author and an associate on Laplace Transformations3,

By B. H. Kear, B. J. Piearcey

The orientation and temperature dependence of the tensile and creep propevties oj Mav-M200 crystals halle been determined. Crystals oriented for single slip exhibit ,maximum ductility, minimum work hardening, and least creep resistance, whereas crystals in multiple slip orientations show nzinimu~n ductility, strongest work hardening, and greatest creep resistance. At 1400" and 1600°F there is a marked improzlenzent in creep strength for orientations approaching [001] and [111], indicating that interactions between dislocations gliding in intersecting octahedral slip systems play an important role in creep resistance. At 1800°F the creep strength is much less dependent on orientation, which is rationalized in terms of slip in cube planes as well as octahedral A frequent mode of failure in high-strength cast nickel-base superalloys is by intergranular fracture, particularly along those grain boundaries oriented transverse to the major stress axis. VerSnyder and ~uard' demonstrated that this problem could be overcome by eliminating transverse grain boundaries through unidirectional solidification. Piearcey and versnyder2 made use of this principle in the development of unidirectionally solidified gas turbine blades and vanes, where the growth direction of the columnar grain structure coincides with the axis of principal stress under operating conditions. The present investigation was undertaken to determine if further improvement in properties may be obtained by eliminating grain boundaries altogether, so as to take advantage of the well-known dependence of mechanical properties of single crystals upon the orientation. 1) EXPERIMENTAL PROCEDURE Single crystals of Mar-M200* were grown from the melt under vacuum by a modified Bridgman method. The melt was poured into a preheated alumina mold, and crystal growth was promoted from one end by appropriate gradient cooling. Tensile and creep specimens (2 in. diam by $ in. gage length) were prepared by a series of operations involving electrical discharge machining, precision grinding, and electropolishing. The orientations of the specimens were determined by the Laue X-ray back-reflection method. Tensile tests were carried out in aWiedemann machine with furnace attachment, using a strain rate planes. In all orientations imzpvouement in the strength charactevistics of the material can be induced by heat treatment. Creep ad stress rupture data for (001) oriented crystals are compared with similar data obtailted previously joy random polycvystalline material, and also columnar grained material having a prejevved (001) orientation. The single-crystal )material exhibits both longer rupture life and lower minimum creep rate at all temperatuves, and the rupture elongation is comparable with that in the columnar grained material. From these results it is concluded that single crystals should and useful application in gas-turbine blades and tanes. The optimum orientation for a blade is considered to be with its axis of principal stvess parallel to (001) ou (111). of 0.0001 sec-'. Load and extension were recorded directly on an X-Y recorder. The strain measuring device consisted of extension arms attached to the grips at one end and leading out of the furnace to an LVDT (linear variable differential transformer) at the other. Creep tests were performed using a standard constant load creep frame. 2) DISCUSSION OF RESULTS 2.1) Structure of Alloy. The structure and segregation in as-cast and heat-treated Mar-M200 has been described in detail else where.~ The main features are as follows: the as-cast material is heavily cored, due to pronounced dendritic segregation during solidification; the dendrites are rich in tungsten and cobalt whereas the interdendritic regions are rich in chromium, titanium, nickel, and carbon. The structure consists of -60 vol pct coherent precipitate of y', basically Ni3(A1,Ti), in a matrix of y (nickel-base solid solution), interspersed in the interdendritic regions with minor MC carbides and -y' eutectic. The y' particles, and y-y' eutectic, contain more titanium, aluminum, and nickel, and less tungsten, cobalt, and chromium than the y matrix. Heat treatment partially removes segregation, eliminates the eutectic, refines the y' dispersion in y, and gives additional partially coherent M23Cs carbide. An as-cast crystal, therefore, is composed primarily of two oriented phases (y + y'), whereas the normally heat-treated crystal consists of three oriented phases (y + y' + MZ3Cs). Typical electron transmission micrographs of the y + y' structure are shown in Fig. 1. Crystals grown in the (100) orientation develop a simple unidirectional dendritic structure, Fig. 2, since (100) happens to be the preferred direction of growth for dendrites in this material. Crystals grown in the {110) and (111) orientations, however, tend to promote equal growth, generally in separate colonies, in the two and three geometrically favored (100) growth directions, respectively. In other orientations of growth, a single (100) dendrite direction generally pre-

Jan 1, 1968

By PERCY E. BARBOUR

TWO YEARS after its organization, the Institute issued its first volume of TRANSACTIONS, covering activities that began in May, 1871, and continued through February, 1873. The preface of this first volume reads: The present volume contains the rules of the Institute, a list of members and associates, an abstract of the proceedings of the-first two years, and a number of papers selected from those proceedings. There is, therefore, nothing new in it. The papers have all been published, according to the custom of the Institute, in the Engineering and Mining Journal, and many of them have been copied into other periodicals. They are republished here, solely to enable members and associates to preserve them in convenient form. Various considerations have determined the selection of papers for this purpose. Some have been omitted at the request of the authors who, having modified the views expressed in them, naturally deprecated a republication of those views. Others have been omitted, in order not to devote too large a proportion of space to single topics, or single branches of mining or metal¬lurgy, in view of the fact that the membership of the Institute extends throughout the whole country, and represents numerous departments of these industries. Some, on the other hand, have been chosen, although not laying claim to special originality, because they contained information of importance, not easily accessible elsewhere, the presentation of which, in a form convenient for reference, was generally desired.

Jan 1, 1921

By W. D. Robertson, W. L. Phillips Jr.

Stress-strain curves were obtained for single crystals of alpha brass in tension and in direct shear. Specimens were strained various amounts in a given slip direction, unloaded, and immediately strained in a second slip direction 60°, 120°, or 180&apos; from the original slip direction. Crystals strained in tension and direct shear had comparable critical resolved shear stresses and stress-strain curves. The density of slip lines in direct shear and in tension was essentially the same. The stress-strain curves obtained in shear were independent of initial orientation, choice of {111 } slip plane, choice of <110> slip direction, prior annealing temperature, and rate of cooling after annealing. There was no recovery after annealing for 4 hr at room temperature or 200°C; recovery was observed after 4 hr at 400°C. The crystals showed no asterism and mechanical properties were completely recoverable up to 20 pct strain. It was found that there is a barrier to slip in all latent close-packed directions, and that the magnitude of these barriers, evaluated at 3 pct strain, is proportional to prior strain and independent of the choice of latent direction in the {111} plane. The formation of Cottrell-Lomer barriers is discussed as a possible explanation for the hardening of the latent systems. AN idealized concept of plastic deformation indicates that a single crystal should yield at some stress that is dependent on crystal perfection and it should then continue to deform plastically by the process of "easy glide," which is characterized by a linear stress-strain curve and a low coefficient, ds/dE, of work-hardening. Hexagonal metal crystals generally conform to this ideal concept of laminar flow. In face-centered cubic metals the range of easy glide is always restricted in magnitude and it is strongly dependent on orientation, composition, crystal size, shape, surface preparation, and temperature. Since one of the principal differences between the two crystal systems, both of which deform by slip on close-packed planes, is the existence of secondary (latent) slip planes in the face-centered cubic crystals, it has been proposed that the transition from easy glide to turbulent flow, characterized by rapid linear hardening, is due to slip on secondary planes intersecting the primary plane.&apos;-.; However, the characteristic differences between individual face-centered cubic metals remain to be explained; in particular, it is not clear why the range of easy glide should vary so greatly in different metals and alloys similarly oriented for single slip. An investigation and comparison of different metals with respect to latent hardening on the primary slip plane should provide some of the information required to specify the necessary and sufficient conditions governing the transition from easy glide to turbulent flow. But, in order to accomplish this purpose, plastic strain must be produced by simple shear in a chosen plane and in a predetermined direction by some form of directed shear apparatus, the results of which must be correlated with the corresponding tension experiments. Two such experiments have been performed previously with zinc and with aluminum. Edwards, Washburn, and Parker" and Edwards and Washburn7 found that the strain-hardening coefficients in two latent directions in the basal plane of zinc were the same as in the primary direction. However, to initiate and propagate slip in either the [2110] or the [1210] direction, following primary slip in the [1l20] direction, it was necessary to increase the stress above that required to continue slip in the primary direction; when the direction of shear was reversed 180 deg plastic strain began at a much lower stress than that required to initiate slip in the original direction and the stress to propagate slip in the reverse direction was lower than the stress to continue slip in the forward direction, indicating a permanent loss of strain-hardening. Rohm and Kochendorfer observed softening in aluminum for all latent close-packed planes and directions. They also found that the critical resolved shear stress obtained from their direct shear apparatus was 50 pct lower than the value obtained from conventional tension tests, that the stress-strain curve was linear at 50 pct plastic strain, and that slip lines were not visible at strains less than 30 pct. At present it is uncertain whether these diverse results correspond to real differences in work-hardening characteristics of the close-packed planes of aluminum and zinc or to differences in experimental technique. In view of Read&apos;s analysis &apos;" of the stress distribution in the experimental arrangement of Rohm and Kochendorfer, there is some reason to question the significance of the latter results. In order to resolve this problem it is necessary to re-valuate the direct-shear technique and either repeat the previous measurements or investigate a third system. The latter choice seemed most likely to produce significant results with respect to work-hardening, and accordingly, it was decided to examine the hardening characteristics of the latent slip directions in alpha-brass. The choice of alpha-brass was dictated by the fact that easy glide is more extensive in this alloy than in any other face-centered cubic metal or alloy and, presumably, more nearly like the idealized hexagonal system. Experimental Procedure Crystals were made in graphite by the Bridge-man method in the form of cylinders, 11/2 in. diam and 8 to 9 in. long. Material for the crystals was 70/30 brass containing the following impurities:

Jan 1, 1959

By J. E. Berry

AII evaluation is made of the acoustic velocity log for measurement of formation porosity. Plots of field-observer1 velocities vs core-measured porosities of sandstones and limestotnes with inter intergranular porosity show that the velocity log gives a useful measure of porotity, in agreement with published data. A new method of plotting electrical and velocity log data makes it easier to recognize hydrocarbon-water coritnct~ from log darn and to make serni-quantitative estinlates of hydrocarbon saturation. Two examples of this interpretation technique are given. This paper also discusses the various factors that affect acoustic velocity and shows how corrections can be made for some of these factors. INTRODUCTION Although the continuous velocity log was developed primarily as an aid to seismic interpretation, it is finding widespread use for measurement of porosity. The purpose of this paper is to evaluate this use of the log. Results are presented for the velocity-porosity relationship in many sandstones and one limestone. Practical applications of porosity values derived from the velocity log to improve interpretation of electrical surveys are presented. Various parameters which affect velocity in porous media are considered. Porosity, composition, cementa-tion, pressure difference (overburden pressure minus fluid pressure), fluid saturation, and wellability are discussed. Some of the ideas are opinions based on general considerations of well logging problems while others are supported by published data and our own observations. Major conclusions from these studies arc given in the body of the paper and detailed discussions of some of the various factors affecting porosity are given in the Appendix. POROSITY Sandstones The primary factor affecting the velocity of sound in porous media is porosity. Wyllie, et al,1 have reported a time average equation for the relationship between velocity and porosity.* This has found considerable acceptance in the industry. Other relationships between velocity and porosity have been proposed, none of which are entirely satisfactory. It is doubtful that any one relationship will completely describe all situations. We have tried an empirical relationship based on correlating log velocities with core-measured porosities. Measured porosities were averaged over a depth interval equal to the spacing used in recording the velocity logs. The depth range for the information used was from 2,000 to 12,000 ft. Velocity measurements were normalized for the effects of depth and overburden pressure. A detailed discussion of the basis for this normalization is given in the Appendix. The change is usually insignificant and when working with individual formations it can be neglected. All velocity measurements were normalized to a depth of 10,000 ft. The velocity-porosity data for sandstones in Fig. 1 came from 20 wells scattered throughout the Mid-Continent and Gulf Coast areas. The scatter of the data points is attributed to three causes: 1. There is no theoretical basis for expecting an exact velocity vs porosity relationship and it is not possible to correct precisely for the effects of such factors as impurities, grain shape, manner of cementation, etc. Some of these factors are discussed in the Appendix. 2. Porosities measured by core analysis are not necessarily representative of what the velocity log "sees". 3. Inaccuracies appear in the velocity log reading. This is particularly true of velocities from one-receiver logging tools.*" A linear-time curve (time-average equation) is plotted in Fig. 1 along with the best straight line through the points. Velocities used for the linear-time curves were 19,500 ft/sec for the matrix velocity (zero porosity) and 5,500 ft/sec for fluid velocity. For clean sandstones with velocities greater than 10,000 ft/sec, there is little difference between the velocity-porosity and the time-porosity curves. Both curves are well within the scatter of data points. The data points in Fig. 1 were restricted primarily to clean sandstones, using the SP and/or gamma-ray logs as clues to the lithology. Where a lithologic de-

By Norman D. Fitz Gerald

The lack of a continuous operating balance in petroleum refining, which is analyzed in this paper, is by no means a feature solely of this division of the oil industry. Serious disequilibria of a capital as well as an operating nature exist both in the producing and marketing departments, while problems in the former and to some degree the latter are complicated by political involvements. Attention has previously been directed to the unstabilizing influence of present proration formulas in stimulating unnecessary drilling.&apos; While equilibrium in petroleum refining operations has been fairly well maintained in the past decade, examination of departures may prove fruitful. Economic analysis is the application of time and motion study to the functioning of management, rather than labor. Properly applied it may reveal changes in policies that would increase the utility of the properties and facilities of the industry for stockholders, employees and the public, while contributing a stabilizing influence to the general economy. The study of economic equilibrium is essentially one of measurement and interpretation, requiring adequate data and the development of a technique of analysis that employs statistical and mathematical methods as a supplement to the broad descriptive phase of economics. Economic equilibrium in petroleum refining is a dual concept. It embraces both the over-all balance between total storage and total demand for major products and the internal balance between the demands and inventories of the various products. The latter is the more complex of the two for it is concerned with proportionating the supplies of the several products stemming from the joint source to the demands for the individual products which are subject to wide variations. All the products are essentially nondurable goods, and they are used both by producers and consumers but in varying proportions. Motor fuel is very largely a consumer&apos;s good, while residual fuel oil is almost entirely a producer&apos;s good, the other products falling between these extremes. The peculiar-

Jan 1, 1939

By Norman D. Fitz Gerald

The lack of a continuous operating balance in petroleum refining, which is analyzed in this paper, is by no means a feature solely of this division of the oil industry. Serious disequilibria of a capital as well as an operating nature exist both in the producing and marketing departments, while problems in the former and to some degree the latter are complicated by political involvements. Attention has previously been directed to the unstabilizing influence of present proration formulas in stimulating unnecessary drilling.&apos; While equilibrium in petroleum refining operations has been fairly well maintained in the past decade, examination of departures may prove fruitful. Economic analysis is the application of time and motion study to the functioning of management, rather than labor. Properly applied it may reveal changes in policies that would increase the utility of the properties and facilities of the industry for stockholders, employees and the public, while contributing a stabilizing influence to the general economy. The study of economic equilibrium is essentially one of measurement and interpretation, requiring adequate data and the development of a technique of analysis that employs statistical and mathematical methods as a supplement to the broad descriptive phase of economics. Economic equilibrium in petroleum refining is a dual concept. It embraces both the over-all balance between total storage and total demand for major products and the internal balance between the demands and inventories of the various products. The latter is the more complex of the two for it is concerned with proportionating the supplies of the several products stemming from the joint source to the demands for the individual products which are subject to wide variations. All the products are essentially nondurable goods, and they are used both by producers and consumers but in varying proportions. Motor fuel is very largely a consumer&apos;s good, while residual fuel oil is almost entirely a producer&apos;s good, the other products falling between these extremes. The peculiar-

Jan 1, 1939

Member ship L P MATHEWSON, Chairman GEORGE D BARRON LOUIS D HUNTOON JOHN A CHURCH, JR H N SPICER Alternates LEWIS W FRANCIS WILBER JUDSON F T RUBIDGE Increase of Membership JOHN A CHURCH, JR, Chairman Other members to be appointed

Jan 1, 1923

THE strike and dip of bedded formations is readily determined by trigonometry if some marker horizon is intercepted by three holes. If no marker can be identified and if orientation of the cores is unknown, as is the usual case in diamond drilling, the determination still can be made readily by the use of a stereonet if the bearing, inclination, and angle the bedding makes with the core axis is known for each of the three holes. Such determination, valid only if the bedding orientation is fairly uniform within the area drilled, is considered simpler, faster, and more effective than any solution previously published. Method: The steps of this procedure are as follows: 1) Mark north and south poles on tracing paper placed over stereonet.* 2) Plot the three diamond drillholes by drawing a line from the center of the net in the direction of the bearings of the holes. Then rotate the paper until each line, in turn, lies along the equatorial diameter of the net; the end of each line is determined by the inclination of the hole measured in degrees from the periphery toward the center of the net along the equatorial diameter. Fig. 1 illustrates a vertical hole and a hole inclined at —23" due east. 3) With the projection of one diamond drillhole along the equatorial diameter, measure from the end of the hole, to the east and then to the west, a dis- tance in degrees equal to the core axis-bedding plane angle. Find two more points by measuring the same number of degrees north then south along the great circle from the end of the drillhole. Draw a circle, the center somewhere along the direction of the projection of the drillhole, to connect these four points. Draw circles for the other two diamond drillholes in the same manner. See Fig. 1 for two circles representing core axis-bedding plane angles of 35" and 23" and Fig. 2 for these plus a third circle representing a core axis-bedding angle of 42" in a hole bearing S 50 W inclined at —52". 4) Rotate the tracing paper until one great circle on the stereonet is found which is tangent to all three of the circles or parts of circles derived in the previous step. Trace this great circle on the paper and join its ends with a straight line passing through the center of the net. The bearing of this line is the strike of the bedding. In Fig. 2 the bedding strikes N 77 E. 5) Rotate the paper until the strike is along the polar diameter of the net. The dip of the bedding is determined by measuring along the equatorial diameter the distance in degrees from the periphery of the net to the great circle derived in step 4. The dip of plane illustrated in Fig. 2 is 55" to the N 13 W. Fig. 3 indicates the solution for three holes whose bearings and inclinations are N 20 W and —43o, due E and —30°, S 30 W and 23" with core axis-bedding angles of 30°, 50°, and 43" respectively. The bedding (stippled area) strikes N 44 W and dips 70" to the southwest.

Jan 1, 1956

By P. J. Spencer, J. N. Pratt

The vapor pressure of manganese over liquid Mn-Sn alloys has been determined by a high-temperature torsion-effusion technique. Alloys containing from 8 to 100 at. pct Mn were investigated in the temperature range jrom 1280" to 1580" and the measured pressure values were used to calculate the partial and integral thermodynamic properties of the liquid alloys. The activities show small negative departures from ideality while the integral heats and excess entropies of mixing are asymmetric inform, changing from positive to negative with increasing manganese content. The possible contribution of various factors to the observed thermodynamic properties is discussed. COMPARATIVELY few thermodynamic data are available for manganese alloy systems.&apos; Therefore, as part of a continuing program of studies of the thermodynamic properties of transition metal alloys, measurements have been made on various binary alloys involving this element. In recent publications,2~3 investigations of liquid Mn-Cu alloys and of the Mn-Au system in both solid and liquid states have been reported. For the first-mentioned system the work suggested that magnetic interactions may be responsible for the observed form of the thermodynamic properties, while in the second the influence of the electrochemical factor appears to be dominant. The present paper describes a similar study of liquid Mn-Sn alloys. Again the thermodynamic properties have been obtained from vapor pressure measurements made by use of a high-temperature torsion-effusion technique.4 A detailed description of the apparatus and of the experimental procedures used in alloy preparation and pressure measurement may be found elsewhere.2&apos;4 EXPERIMENTAL RESULTS Sixteen alloys, ranging in composition from 8 to 100 at. pct Mn, were prepared from spectroscopically standardized manganese of 99.99 pct purity and tin of 99.999 pct purity, both supplied by Johnson-Matthey and Co., Ltd. One-gram samples of the alloys were obtained by carefully weighing appropriate amounts of the pure components into an effusion cell; this was then suspended in the apparatus and the metals melted together in situ by heating under vacuum to approximately 1550°K. After allowing sufficient time for a homogeneous liquid alloy to be formed, vapor pressure measurements were commenced. These were determined as rapidly as possible at a series of steady temperatures within the range of interest. The duration of experimental runs on individual samples was kept sufficiently short to ensure insignificant varia- tion of alloy composition during investigation. After completing pressure measurements, the alloys were rapidly cooled and their compositions checked by weighing or chemical analysis. All experiments were conducted using effusion cells machined entirely from boron nitride. Measurements were made using a variety of cells with orifice areas ranging from 0.0032 to 0.0075 sq cm and lengths of the order of 0.04 cm; the usual effusion correction factors for orifice geometry and molecular distribution were calculated using Freeman and Searcy&apos;s equation5 and had values between 0.6 and 0.75 for the orifices employed here. The vapor pressures of manganese over the alloys were measured at approximately 20°K intervals in the temperature range 1280" to 1580°K. In view of the close approximation of the measured pressures to Clausius-Clapeyron behavior in the experimental temperature range, the data for each alloy have been expressed by equations of the form: logp(atm) =-A/T + B A least-squares computer treatment was applied to the vapor pressure values in order to obtain the coefficients A and B with their associated error. The resulting equations are listed in Table I, together with the equation for pure solid manganese obtained from a previous study.4 To minimize the effect of possible apparatus calibration errors, the activities and partial free energies of manganese in the alloys were calculated by initial reference to the latter equation, obtained from identical torsion-effusion measurements. The immediately resulting thermodynamic quantities, based on a solid manganese reference state, were then converted to refer to the more appropriate supercooled pure liquid manganese standard; tabulated values of the free energies of solid and liquid manganese from Hultgren et al.&apos; were used for this purpose. Partial entropies of solution of manganese were calculated from the temperature coefficients of the free energies and partial heats from the Gibbs-Helmholtz relationship.

Jan 1, 1969