Search Documents

By M. L. Leonardi

THE Searles Lake orebody is located in the north- west corner of San Bernardlno County. It is a dry lake bed with an exposed salt surface covering an area of 12 square miles. Recoverable mineral values are contained in the mother liquor below the surface of the lake. Stratification in the lake bed has separated the brine into two bodies which dlffer in composition. Although liquor is processed from both bodies, this paper will discuss only the upper structure brine. Fig. 1 illustrates a typical cross-section of the two commercial orebodies. The orebody is composed of a porous salt deposit 70 to 90 ft deep. The upper structure is separated from the lower orebody by a 12 to 16-ft thick impervious mud seam, as shown in Fig. 1. These salt structures are composed of 55 pct solid-phase salts and 45 pct voids which are filled with the original mother liquor. The brine wells are drilled to the separating mud seam and cased to wlthin 10 ft of the bottom. This is done to draw the brine horizontally from the bottom of the structure. It is pumped with multistage centrifugal pumps Into the plant at the rate of 3 milllon gal per day. The first process that was successful was developed by Charles P. Grimwood for the recovery of potash. The first evaporator unit was built in 1916. In the early twenties, Dr. Morse worked out a process for the recovery of borax. This made the cycle more efficient, as the end liquor could be sent back to the evaporators rather than being sewered. In 1926 the American Potash & Chemical Corp. was formed as a new company, and the entire plant was remodeled. The plant at that time produced only potash, borax, and boric acid. Since then the American Potash & Chemical Corp. has added processes for the production of USP boric acid, refined potash, sulphate of potash, soda ash, salt cake, lithium concentrates, Pyrobor (Na2B4O7) bromine, phosphoric acid, and lithium carbonate. The main plant cycle may be depicted as a closed cycle, see Fig. 2. The raw material, brine, enters the cycle to be mixed with the end liquor, known as ML2, from the pentahydrate borax crystallizers. The mixture of these two forms evaporator feed. Evaporator feed is pumped to the evaporators where it is concentrated, with respect to potash and borax. In the same operation water vapor, sodium chloride, salt trap salt, and clarifier salt are removed from the cycle, see Fig. 3 for potash plant product. The evaporators produce a concentrated liquor which contains approximately 19.5 pct KCI. This liquor is diluted as it enters the potash plant to keep all salts, except potash (KCI, 97.0 pct) in solution. Here the moist potash leaves the cycle at 100°F. The end liquor, known as ML1, is pumped to the borax pentahydrate crystallizers, where crude borax pentahydrate is crystallized and removed as solid phase. The ML2 is sent back to pan feed to be reconcen-trated, see page 207. Note that the only water to leave the cycle is in the form of vapor and moisture in the solid phase products crystallized. Thus there is a constantly cycling volume of liquor to which brine is added. Since the volume of liquor cycled does not increase, the brine is, in effect, evaporated to dryness. This would be true if there were no liquor losses. But, as in all processes, there are always unavoidable and accidental losses which reduce the volume of cycling liquors. The losses must be made up with brine. The concentration process is the beginning and the end of the cycling liquors. In this process there are three evaporator units of the triple effect counter-current type, that is, there are three pans in each unit and the heat flows in one direction while the liquor flows the other way through the evaporator pans, see Fig. 4. During the evaporation process a great deal of sodium chloride, burkeite, some sodium carbonate monohydrate, and a little lithium-sodium phosphate are crystallized. The volume of these salts is so great that they must be removed as they are formed or the process would come to a standstill. Brine and recycled mother liquor No. 2 enter the third effect evaporator pan from the evaporator feed storage tanks, see Fig. 5. A steady flow of liquor is removed from the bottom of the No. 3 pan and is pumped through the No. 3 cone of the salt trap, a clear liquor being returned to the NO. 3 pan. A portion of this clear liquor is pumped to the second effect pan. This process is repeated in each pan. The liquor from the No. 2 pan is pumped through the No. 2 salt trap cone and returned to the No. 2 pan.

Jan 1, 1955

By J. Szekely, Robert J. Fisher

A formulation is Presented and solutions are given for the problem of transient heat conduction in a sphere that undergoes a spatially uniform radiative heat exchange with its environment. The solutions were obtained by the numerical integration of the appropriate Partial differential equation and are Presented in a graphical form by Plotting a dimensionless average temperature against the Fourier number with the radiation number as a paranreter, for various initial sphere and environment temperatures. In addition to these numerical results asymptotic analytical solutions are also given. PROBLEMS involving the transient heating or cooling of droplets and particles frequently arise and are of importance in metallurgical operations. Spray refining, vacuum degassing, high-temperature gas-solid reaction systems, and pebble heaters are but few of the numerous examples that may be quoted. The practical interest in these problems from a design or operational point of view is to evaluate the change in the particle temperature with the time given its physical properties, initial temperature, and that of the environment. At the high temperatures encountered the principal mode of heat transfer between the particles and their environment is by thermal radiation; in case of vacuum degassing due to the very low thermal conductivity of the gas space the convec-tive components are negligible and radiation is the only heat transfer mechanism. Although much work has been done on transient heat conduction problems, the special class mentioned here, in which thermal radiation is specified at the bounding surface, received little attention to date. One contributory factor to this situation may be the nonlinearity of the radiation term in temperature, which in general precludes the use of analytical techniques and requires numerical or analog solution of the appropriate differential equations. In fact the only solutions of general nature that are available at present pertain to semi-infinite media and slabs.'-3 The work on which the paper reports forms part of a program aimed at the theoretical and experimental study of transient radiative heat exchange between particles and their environment. The purpose of the present paper is to develop a formulation and solutions to the problem of transient heat conduction in a sphere that undergoes a spatially uniform radiative heat exchange with its surroundings. The solutions, obtained by the numerical integration of the appropriate differential equations, will be presented graphically, by plotting dimensionless parame- ters covering the range of variables relevant to metallurgical interests, thus affording a ready reference for design calculations. In addition to these results, approximate analytical solutions are also given which represent asymptotes, corresponding to extreme values of the variables mentioned. FORMULATION Consider a spherical particle of radius, a, initially at uniform temperature, Ti (T measured on the absolute scale), having a thermal conductivity, k, density, , specific heat, C, and thermal diffusivity, a. At time = 0 let this particle be exposed to an environment which is at a temperature T, and subsequently let there be a purely radiative heat exchange between the particle and the environment resulting in a spatially uniform heat flux at the surface. If in addition to the above we make the assumptions that the sphere is a gray body radiator, homogeneous, isotropic, and opaque, and that the physical properties are independent of temperature, conservation of heat in the sphere may be written as follows: The boundary condition contained in Eq. [3] states that the initial temperature of the sphere is considered uniform, equalling Ti, whereas Eq. [4] is readily obtained from symmetry considerations. Eq. [5] expresses the continuity of the heat flux at the surface of the sphere, or in other words the condition that the rate of heat exchange between the sur-

Jan 1, 1969

Thomas H. Beddall, so we are informed by Major J. B. Carlock, has been promoted and is now Adjutant of the 1st Battalion, 1st Gas Regi¬ ment. He was awarded, last summer, the Croix de Guerre. R. A. Bull. See letter in Proceedings of Milwaukee Meeting. Captain Stanley C. Bullock's record since entering the service is given as follows in a letter recently received from Mrs. Bullock: Resigned position of mine manager in Chile in November, 1915, to return to England to obtain commission in Royal Engineers. Joined Officers' Training Corps, Dec. 20, 1915. Commission gazetted, Jan. 27, 1916, 2d Lieut., R. E. Landed in France, Feb. 6, 1916. Posted to 179th Tunnelling Co., R. E. Took part in following battles: Somme, 1916; Ypres;1917; Arras, 1917; Somme, March and July, 1917; Messines, 1917. Gazetted: Acting Captain, July 11, 1916; Temp.-Lieutenant, Oct. 26, 1916; Captain, Sept. 29, 1918. Awarded Military Cross, Jan. 1, 1918, for conspicuous bravery and devotion to duty under a heavy enemy gas bombardment, when, by his example and perseverance in spite of every difficulty and obstacle, mining work was successfully completed which was vital for the success of the operations. The Cross was presented to Capt. Bullock by the King, on Sept. 25, 1918. First Lieut. J. J. Cadot, in a letter sent to Mr. H. `V. Hardinge from France, says he has been at the "Front." He also mentions that the Boche "is a good sprinter."

Jan 12, 1918

By Larry J. Tucker

INTRODUCTION The orebody at Pea Ridge strikes NE-SW and dips at about 800 to the SE. The ore and surrounding rocks are Pre-Cambrian in age. These rocks are usually very competent. Locally strong jointing has caused problems and toward the hangingwall dikes have caused particular problems during or after the open stoping phase of production. About 396 m of sediments lie over the ore. The shape and mineral content of the orebody has been fairly consistent so far with production areas lying from the 1375 to the 2475 levels. The deeper limits of the ore- body haven't been found yet. The ore is high grade magnetite with a strike length of over 600 m and a maximum width of over 180 m on some levels at the center of the orebody. Production at Pea Ridge for the first three years of operation came from two types of open stopes. The original stopes were recovered with horizontal production rings being drilled and blasted from vertical raises. Later a more typical sublevel stoping method using vertical production rings from one or more drilling sub- levels was used. There were a number of reasons for the selection of open stoping as the initial production method at Pea Ridge. First, it was judged that the ore was not of a block cave quality. After fifteen years of production, this assumption can be verified. There was some concern during the planning days for the potential for high flow rates of water into the mine from aquifers in the sediments lying over the orebody. Dewatering wells from surface and underground were put in as a precaution and nothing came of this potential problem. Open stoping and its resulting pillar structure put off this problem by supporting the sediments a few years longer. For a moderate investment in level development some production from open stoping was quickly realized. The first open stopes were brought in on what was then the bottom mine production level (2275), near the shaft pillar and situated on the footwall. This production practice of stoping on the heels of development from shaft pillar westward and from footwall to hangingwall continued through the open stope phases of production at Pea Ridge for many years. From the standpoint of mine efficiency and pillar stability, this would not seem to be a recommended mining practice. 74 570 w electric slushers, using 1.37 m dippers, pulled the open stope ore out into 18 ton bottom dump cars. Ordinarily five of these cars made up a train, which was pulled to the dump area by a trolley powered electric locomotive. Open stoping had the disadvantage that 100% of the recoverable portions of the orebody had to be developed in order to recover 33% of the ore. 67% of the ore was left behind in a large pillar system. For many years we had no planned method for recovery of these pillars. Mining methods are of course, limited by the existing technology. Advancing technology, coupled with the limited production capabilities of open stoping, low efficiencies and high relative cost early in the history of the operation recommended that other mining methods be looked at. In Sweden, considerable practical experience, coupled with a large amount of theoretical work had become available on sublevel caving. To Pea Ridge it offered the apparent benefits of: 1) The flexibility of diesel powered trackless haulage. 2) The efficiency of two machines to one operator on longhole drilling. 3) A multilevel production picture with a large number of drawpoints for ore recovery. 4) 100% recovery of the mineable portion of the orebody in one production pass, with no pillar recovery problems left behind. This paper outlines the experiments and experiences which Pea Ridge has gone through with sublevel caving from 1967 to this date.

Jan 1, 1981

By L. B. Slichter

It has been estimated that rock exposures in most mining districts aggregate less than 1 per cent. of the total surface area.1 Conclusions concerning the hidden 99 per cent. necessarily have been based on knowledge of only a small fraction of the surface, and from this limited information the geologist has been obliged to deduce the approximate and general nature of the underlying formations. In the search for ore it is necessary to supplement this general picture with greater detail. Fairly accurate knowledge of relatively small zones is required. This knowledge is carefully sought in many different ways—detailed interpretations of geological history, the tracing of float, the use of test pits, of trenching, of drilling, and of other methods. Practical ingenuity, scientific brilliance, great perseverance and patience, and the expenditure of large sums of money have all been a part of this search. The problem of exploring beneath cover with economy, and of obtaining essential information which this cover hides, is obviously a difficult one. It is also a very important one, for geologist's inform us that already the story of the 1 per cent. exposed outcrops has been largely read.V here remains the nearly virgin field comprised in the hidden 99 per cent.: and the importance of this zone is bound to increase continually. In recent years, the problems connected with the exploration of this "99 per cent. zone" have attracted a constantly enlarging group of investigators and at present greater efforts than ever before are being made to resolve them. This work, in it's various special aspects, has enlisted, beside geologists, the cooperative efforts of chemists, physicists, and mathematicians. The progress made in this development should be kept before those directing explorations in order that due advantage may be taken of a changing situation. My subject concerns certain aspects of one of the older physical methods of exploration, the magnetic method. This method is familiar in principle to most of us, arid because of its age., is especially suitable for

Jan 1, 1929

By H. E. Stauss, J. Hino

INTEREST in silicon has arisen again in the past decade as a result of improvements in crystal rectifiers.' Although the preparation of silicon was first reported by Berzelius in 1880, the early product was of relatively low purity, and only the need for rectifiers in World War II led to the production of a 99.9+ pct pure powder. This material in crystalline form was consolidated into massive silicon for use, and the method developed was to melt it with selected added constituents as "doping" agents. Melting techniques, therefore, are of great importance. There are two basic problems in producing silicon ingots free of doping additions; one is the prevention of spitting and the other is prevention of cracking of the ingot during freezing. The most satisfactory arrangement yet developed for producing massive silicon is to melt and freeze in a cylindrical quartz crucible surrounded by a concentric heating element and concentric radiation shields or insulation. For example, use can be made of a tubular heater with a high frequency generator as the source of power and reflecting shields of alundum cylinders. The spitting of silicon is related to gas evolution, and the gas comes from two primary causes—adsorbed gas and the reaction products of silicon and the crucible. Gas is also released from bubbles contained in the quartz crucible walls. Improved removal of adsorbed gas can be achieved by means of controlled melting and freezing. The seriousness of the problem in vacuo is reduced with an electrically operated mechanical movement of the high frequency power coil. The upper portion of the powder charge is melted first and the high frequency coil lowered until the powder is completely molten. During cooling the high frequency coil is raised slowly. These means also reduce the final nonviolent extrusion of large beads of metal through the ingot top during freezing. Better control of spitting and bead extrusion is obtained when melting is done under helium at. atmospheric pressure instead of in vacuo. The problem of reaction between silicon charge and crucible in practice is confined to the reaction between silicon and quartz. This2 apparently is: Si + SiO2 + 2SiO The part that this reaction plays in spitting has not been isolated for separate study. SiO is a volatile vapor at the melting point; of silicon and is released freely during melting in vacuo, but hardly at all in helium at atmospheric pressure. The cracking of ingots is a major difficulty in melting silicon, and its prevention requires special melting techniques or the addition of "toughening" agents such as aluminum or beryllium.' The cracking of the ingots has been explained as being the result of the expansion that occurs upon freezing; although direct observation of freezing ingots reveals visible cracks on the surface only after a red heat has been reached, suggesting that cracking is the result of differential contraction of silicon and quartz. Silicon wets quartz, and the ingot adheres tightly to the crucible. Therefore as ingot and crucible cool, the two either have to pull apart, or at least one must crack. Surprisingly, in spite of the relative thinness of the quartz and the thickness of the ingot, the ingot and the crucible both crack. Microscopic and X-ray4 studies fail to show any plastic flow other than twinning in the ingots. Slow cooling fails to prevent cracking. Another possible solution to cracking is to weaken the crucible. Use of thin-walled crucibles finally led to success with fused quartz crucibles with a wall thickness of 0.25 to 0.50 mm. With such thin-walled fused quartz crucibles consistently uniform success is secured in producing sound ingots 30 mm in diam from the purest available grade of silicon (99.9+) without the use of any type of addition. Melts are made in the size range of 50 to 100 g. Omission of a deliberately added doping agent is not sufficient to insure pure ingots. The reaction of silicon with crucibles and the resultant solution of impurities in the silicon is well-established." In this laboratory, the presence of Al, Be, and Zr has been found spectroscopically in ingots melted in contact with alumina, beryllia, and zircon. The best crucible materials reported in the literature are MgO and SiO2. Use of MgO in this laboratory has resulted in a heavy deposit of magnesium on the furnace walls, showing that a reduction of the magnesia occurred and the resulting magnesium removed from the melt by volatilization. In the case of quartz, the silica is reduced and SiO liberated to deposit on the equipment walls. There probably is real danger that oxygen is dissolved in the ingot when either magnesia or silica is used as the crucible material. Preliminary analyses by Dean Walter in his vacuum unit in this laboratory6 indicate the presence of oxygen in undoped silicon melted in quartz.

Jan 1, 1953

By C. E. Hottman, R. K. Johnson

Fluid pressure within the pore space of shales can be determined by using data obtained from both acoustic and resistivity logs. The method involves establishing relationships between the common logarithm of shale transit time or shale resistivity and depth for hydrostatic-pres-sure formations. On a plot of transit time vs depth, a linear relationship is generally observed, whereas on a plot of resistivity vs depth, a nonlinear trend exists. Divergence of observed transit time or resistivity values from those obtained from established normal compaction trends rinder hydrostatic pressure conditions is a measure of the pore fluid pressure in the shale and, thus, in adjacent isolated permeable formations. This relationship has been empirically established with actual pressure measurements in adjacent permeable formations. The use of these data and this method permits the interpretation of fluid pres.rure from acoustic and resistivity measurements with an accuracy of approximately 0.04 psilft, or about 400 psi at 10,000 ft. The standard deviation for the resistivity method is 0.022 psi/ft, and for the acoustic method 0.020 psi/ft. Knowledge of the first occurrence of overpressures, and of the precise pressure-depth relationship in a geologic province, enab1es improvements in drilling techniques, casing progroms, completion methods and reservoir evalzmtions. INTRODUCTION CENKRAL STATEMENT Operators engaged in the search for and production of hydrocarbon reserves in Tertiary basins are more and more frequently confronted with complications associated with over pressured (abnormally high fluid pressure) formations. This is particularly true in the Texas-Louisiana Gulf Coast area. The problems associated with these formations are of direct concern to the combined activities of all phases of operations, i.e., geophysical, drilling, geological and petroleum engineering.' - Knowledge of the pressure distribution of a given area of operations would greatly reduce the magnitude of many of these complexities and in some cases would completely eliminate specific problems. his pape; presents techniques developed for estimating formation pressures from interpretations of acoustic and electric log data. Specifically: the acoustical and electrical properties of shales, reflected by conventional acoustic and electrical surveys, can be used to infer certain reservoir properties, such as formation pressure, at any level in a well. It has been possible to develop these techniques because of a firm understanding of the basic principles that govern and apply to such overpressured provinces. NORMAL PRESSUKES Normal pressures refer to formation pressures which are approximately equal to the hydrostatic head of a column of water of equal depth. If the formations were opened to the atmosphere, a column of water from the ground surface to the subsurface formation depth would balance the formation pressure. On the Gulf Coast, the shallow, predominantly sand formations contain fluids which are under hydrostatic pressure. These formations are said to be normally pressured or to have a normal pressure gradient.* Experience has shown that the normal pressure gradient on the Gulf Coast is approximately 0.465 psi/ft of depth. OVERPRESSURES Formations with pressures higher than hydrostatic are encountered at varying depths in many areas. These formations are referred to as being abnormally pressured, abnormally high pressured, or overpressured. Formation pressures up to twice the hydrostatic pressure have been observed. These formations require extreme care and much expense to drill and to exploit. COMPACTION-FLUID PRESSURE RELATIONS THEORY The generation of overpressured formations in Tertiary sections of the Gulf Coast and several other Tertiary sedimentary basins is, in general terms, considered to be primarily the result of compaction phenomena.' This portion of the paper presents a brief review of the theory which associates compaction and fluid pressure relations, and should thus provide the necessary background for an understanding of the techniques presented. See Hubbert and Rubey' for a more comprehensive treatment of this subject. The theory of the consolidation of a water-saturated clay' has been well established by workers in soil mechanics. The concept is explained by a model with perforated metal plates separated by metal springs and water and enclosed in a cylindrical tube. Fig. 1 is a schematic representation of such a model (see Ref. 5, Fig. 27, page 74). The springs simulate communication between clay particles, and the plates simulate the clay particles. Mano-

Jan 1, 1966

By C. S. Smith, W. M. Williams

THE quantitative study of grain shape in three dimensions has been a difficult one from the practical standpoint. Experiments on grain shape have usually been based on indirect observations of two-dimensional metallographic samples or on grains separated by intergranular corrosion or fracture. The latter method was used in particular by Deschl in 1919 in observing the shapes of ß-brass grains which had been separated with mercury. The similarity in detail of shape and packing that exists between bubbles in a soap froth and metal grains was noted by Desch who remarks that: "Surface tension has an. important share in determining the form of the crystal grains in a solidifying metal and such grains have a tendency to assume the shape of foam cells." More recently the relation between grain shape and grain growth has been studied by Harker and Parker.' The importance of surface tension forces in determining microstructure has been discussed by Smith," and an analysis of the topologi-cal rules that apply to such structures has been made by the same author.' Biologists have made valuable contributions to the general problem of shape and form in an assembly of space-filling cells subject to surface tension forces. Particular mention must be made of the extensive researches of Lewis5,8 on botanical and anatomical tissues, and Matzke and Nestler,7,8 who have made painstaking studies of bubble shapes in different kinds of foam. The present paper introduces a new method of studying individual grains in particular alloys—a method which may well find use in other metallurgical researches, and which seems also to be applicable in biological problems. Metal Grains in Three Dimensions The individual grains in a piece of metal or the bubbles in a soap froth must satisfy two conditions —they must be in juxtaposition so as to fill space and their interfaces must conform to the laws of surface tension. If a further restriction is imposed, namely, that only one type of polyhedron be used, then the sole possibility is an assembly of "minimal" tetrakaidecahedra," each polyhedron having eight doubly-curved hexagonal faces and six plane quadrilateral faces, the angles between adjacent faces being 120". Such cells could be stacked on a body-centered cubic lattice and would be quite stable. For many years it was believed that soap bubbles actually possessed the shape of this ideal body, and the hypothesis was the starting point for several investigations on the shapes of soap bubbles, biological cells, and metal grains. These investigations have shown, what might have been obvious in the beginning, that if the condition of symmetry is relaxed the tetrakaidecahedron is almost never found. If we retain only the rule that all contacts should be in local surface tension equilibrium and that the assembly should fill space, metal grains may then take a nearly infinite variety of shapes and no single one may be regarded as an archetype. These two conditions, which are fully discussed in one of the previously mentioned papers,' lead us to think of a typical grain in an annealed metal as having the following characteristics: 1—A grain may have any number of faces, but usually between nine and eighteen. The faces (each of which is, of course, shared by two grains in the assembly) may have any number of edges, but usually between four and six. Pentagons are by far the most frequent. 2—In the assembly of grains each edge is shared by three faces and by three grains. Each vertex is a point shared by four grains, six faces, and four

Jan 1, 1953

The pressure of the gas in equilibrium with sphalerite has been determined in the temperature range of 680' to 825°C, using the Knudsen orifice method. A comparison of these experimental pressures with those calculated from thermal data and from other equilibrium measurements shows that the vapor above sphalerite is predominantly dissociated ZnS. Equations have been given for correctly calculating dissociation pressures using the Knudsen orifice method. It has been shown that the experimentally determined pressure is the same, whether the zinc sulphide is sphalerite or not, or a mixture of wurtzite and sphalerite. CONFLICTING points of view appear in the literature on the constitution of the vapor in equilibrium with solid zinc sulphide in the vicinity of 800°C. By comparing the dissociation pressure calculated from thermodynamic data and the vapor-pressure determination of ZnS by Veselovski,1 Lumsden2 has concluded that the vapor consists largely of dissociated ZnS. Sen Gupta,' however, concludes from his spectroscopic determinations that the vapor is largely ZnS molecules. In view of the fact that the thermodynamically calculated' dissociation pressure is higher than that experimentally measured by Veselovski, it seemed in order to repeat Veselovski's measurements. Experimental Procedure The method used for the determination of the pressures in this papel- is the Knudsen effusion cell. The apparatus and procedure were described in a previous paper- from this laboratory on the determination of the vapor pressure of silver. The only difference is that the Knudsen cell in this work is made from platinum and there is no external cover around the cell. The cell is an ordinary platinum crucible of 2.2 cm top diameter with a capsule cover. It was thought that platinum might stand up at these temperatures to the solid and gaseous ZnS, since it was found that the weight of the platinum cell itself did not change appreciably on heating ZnS in it at the working temperatures. To insure that reaction of the zinc sulphide with the cell was not giving' a false value, a stabilized zirconia cell was employed for check runs. Fig. 1 shows the comparison, which is satisfactory. Veselovski previously had measured the vapor pressure of ZnS using a silica Knudsen effusion cell. On repeating his experiment in this laboratory, it was found that ZnS at-tacked the silica cell, giving it a marked frosty appearance. This led to the belief that Veselovski's result:; may be in error. Also, he was operating at pressures above the range ordinarily considered safe for the Knudsen method. The effusion rate was measured by weighing the cell before and after each run. The weight loss during heating to temperature and cooling down was measured and subtracted from the weight loss during the actual run. The zinc sulphide used in this investigation was from two sources: Fisher cp grade, and a sample of pure sphalerite supplied by Mr. E. A. Anderson of the New Jersey Zinc Co. Before and after the series of runs with Fisher ZnS, X-ray analysis showed that both wurtzite and sphalerite were present. However, the ratio of sphalerite to wurtzite increased. All measurements were made below the transition temperature which has been reported" to be 1020°C. The data obtained in this investigation are tabulated in Table I. The pressure was calculated by the usual Knudsen formula" on the assumption that ZnS molecules were effusing. From these data, using pure sphalerite in the platinum Knudsen cell, the vapor pressure of ZnS, in mm of Hg, as a function of temperature is given by the solid line in Fig. 1. The best straight line, as determined by the method of least squares, is given by 14405 logpzns =-14405/T +11.032. A comparison of these results with Veselovski's shows that his results are about 50 pct lower. Discussion The vapor in equilibrium with solid zinc sulphide in the temperature range of this study will consist of Zn, S2, and ZnS mol, since other species of zinc and sulphur' are relatively unstable. The question to be settled is whether or not ZnS is largely dissociated. The derivation8 which follows gives the method of calculating the pressure of zinc and sulphur over solid ZnS, assuming complete dissociation, from Knudsen cell data. The free energy of the reaction 2 ZnS(solid) ? 2 Zn(gas) + S2(gas) is given by ?F?° = -RT In K = —RT In p12p2 where p1 is the zinc pressure and p is the sulphur pressure. If dissociation occurs in a closed system,

Jan 1, 1955

By J. C. Bradley

THE relation of annealing temperature to conductivity of copper wire has been determined.1 Conductivity hard was 98.26 per cent. After a 10-min. heating at 200° C. it was 98.69. By annealing 10 min. at 300° C. a large increase, to 100.93, occurred. Maximum conductivity, 101.15, was attained after a 500° C. anneal; thereafter it decreased to 100.53 after a 950° C. anneal. If copper is gassed the decrease is much more than this. MATERIAL AND METHOD The work was done on high grade electrolytic copper, 99.942 per cent. copper-plus silver, silver 0.0008 per cent. It was hot-rolled to 3 in., then cold drawn to 0.080 in. The wire was cut into 25 5-ft. lengths and numbered 1 to 25 as cut. Four samples were tested hard. The others were wound into 5-in. diameter coils. For the 100° C. heating a coil was put into water, the water brought to boiling, and the wire kept at this temperature for 10 min. For the higher temperatures the coils were placed in envelopes of sheet copper, a little water added, and the envelopes sealed by folding over the edges twice, and hammering them together. This kept the air out very well. The envelope and wire were brought to the desired temperature; this was maintained for 10 min., then the whole was water-quenched.

Jan 1, 1927

By E. DeGolyer

The only known direct method of discovering oil deposits is by the drilling of test wells. Such exploration is always hazardous and generally very costly. The problem of the prospector, therefore, is to select test sites that are favorably located and so to reduce the odds against his venture. Early in the history of the oil industry, it was realized that oil and gas deposits, other conditions being favorable, were usually found in anticlinal types of structure. This very undestandable and rational habit of occurrence furnished the first substantial clue to the prospector. Oil occurs in sedimentary rocks, and beds of such rocks are deposited originally in approximately parallel layers. An anticline at the surface, therefore, could be accepted as an indication of an anticline in lower beds. Structural geology became the tool of the prospector, and by its use in the past two decades the majority of the known important oil deposits of the world have been discovered. This is but a partial, and the simplest, statement of the problem, Nine-tenths and more of the important oil pools of the world belong to the great class of accumulations controlled by structural traps—anti-clines, faulted structures, salt domes, etc.—but by no means all of these structures are clearly or adequately expressed at the surface. As the more obvious anticlines were explored and the search for new deposits led to the testing of progressively deeper beds, it became more and more apparent that marked favorable structures involving petroliferous rocks can, and do, exist without any marked surface expression. There are great areas where the surface, covered by some masking material such as water, alluvium, glacial deposits, or sand dunes, affords no clue to structural conditions in the subsurface, and there are also regions where the surface formations are unconformable with the oil-bearing formations. The structure in which the prospector is fundamentally interested is that of the oil-bearing formation itself, together with roof and floor beds. No other geologic information is of interest or importance to him except as it affords clues to the stratigraphy and structure of the supposed oil-bearing formations.

Jan 1, 1932

By AIME AIME

LIFE will not be difficult for those who attend the fall meeting of the Petroleum Division at the Conoco Club, Ponca City, Okla., Sept. 30-Oct. 1. An attractive program to appeal to oil company executives and lawyers, as well as technologists, has been arranged and the Continental Oil Co. has contributed for the occasion the buildings, grounds and facilities of the club. E. 0. Bennett, Continental Oil Co., Ponca City, is chairman of the arrangements committee, and reservations for rooms and trips, requests for information, etc., should be sent to him.

Jan 1, 1932

By W. K. Lewis

During the last decade the petroleum refinery engineer has made great progress in achieving a better understanding of the physical behavior of hydrocarbon mixtures, with particular reference to their pressure-temperature-volume relationships, the mechanism of the evaporation of liquids, the condensation of vapors, including the changes in composition, and the heat effects accompanying them. With the new insight into the mechanism of movement of oil and gas through the formations in which they occur, achieved by the production engineer, it is clear that the latter will need to utilize in the solution of his own problems much of the information outlined above. It is the purpose of this paper to outline the portions of that information that seem most certain to prove of importance in production work. Properties of Pure Hydrocarbons While it is true that petroleum always consists of highly complex mixtures of hydrocarbons, none the less understanding of the behavior of the mixture must be based upon a knowledge of the properties of the pure components. However, in view of the tremendous number of hydrocarbons existing in petroleum, the determination and formulation of the properties of all of them would seem a discouraging task. The difficulty of the situation is increased by the undoubted facts that the overwhelming majority of chemical individuals in petroleum have never been isolated as pure compounds, none of their physical properties have been determined and even their chemical constitution is unknown. The situation would be hopeless were it not for the fact that certain extraordinary correlations of important properties of various hydrocarbons have been discovered which make it possible to predict those properties for a given chemical individual on the basis of a very limited characterization of it. Thus one can predict the vapor-pressure curve of an unknown hydrocarbon over a considerable range from the knowledge of a

Jan 1, 1934

By J. R. Sturgul

Two problems which are common to nearly every branch of applied physics, including geophysics, are the ‘Dirichlet Problem’ and the ‘Poisson Problem.’ A numerical method for their solution is derived and a problem of heat flow in a plate is solved using a high-speed digital computer. The solution to this problem is presented in a form which illustrates the versatility of computer output.

Jan 1, 1969

By N. Jaffe, J. E. Dorn

This investigation is concerned with the possibility that the creep resistance of metals might be reduced as a result of recovery at the creep temperature when the applied stress is reduced. For this purpose the effect of stress on the recovery of the creep behavior of pure polycrys talline aluminum was investigated in the cross-slip temperature range where the activation energy for creep is 28.000 cal per mole. Before recovery all specimens were given the same substructure by creeping them under a stress of 7800psi to a strain of 0.218. Recovery was then accomplished by holding the specimens at the creep temperatures of 327" and 337°K under a series of reduced stresses for various periods of time. When the original stress was reapplied the specimens crept more rapidly than when the original stress was first removed, illustrating that recovery did take place. The extent of recovery could be indexed in terms of the UNDER certain conditions of test, the creep rate decreases over the primary stage of creep often by as much as a factor of 10~B. Since the external variables of stress and temperature are held constant, such pronounced and significant changes in the creep rate must be attributed to various substructural modifications that are introduced as a result of creep itself. At the secondary stage of creep, over which the creep rate remains constant and the substructure no longer changes, a balance must be achieved between the rate of increase in creep resistance due to creep straining and the rate of recovery of the substructural modifications. The general validity of these concepts on substructural changes has already been shown,' including the corollary that a more creep-resistant substructure is introduced under a more rapid creep rate arising from a higher applied stress.' In spite of these well-documented facts, very little progress has been additional strain undertaken by the recovered specimen to achieve the same strain rate as the unrecovered specimen. It is significant that the higher recovery stresses gave the most rapid rates of recovery. Over the high range of reduced stresses, where some creq took place during recovery, the activation energy for recovery equaled that for creep, namely 28,000 cal per mole. But for stresses during recovery below 0.80 of the original creep stress, no creep was detected during recovery and an activation energy for recovery of about 72,000 cal per mole was obtained. Whereas the activation energy of 28,000 cal per mole suggests that cross-slip of dislocations is responsible for this recovery, the mechanism for the 72,000 cal per mole process is not known. This activation energy, however, is about twice that for self-difhsion. made in determining, in satisfactory detail, precisely what substructural changes so effectively modify the creep rate.' Up to the present, electron microscopy has failed to uncover, in a satisfactory quantitative manner, the mechanistic processes involved. Since, however, creep, at least at moderate and high temperatures, arises from one or more types of dynamic recovery processes, it should be possible to shed additional light on the total problem by investigating the recovery of creep resistance. The importance of such an investigation becomes apparent when the fact is recognized that there has yet been no direct experimental proof that the rate of softening due to substructural changes as a result of recovery equals the rate of hardening due to creep-induced substructural strengthening over the secondary stages of creep. Furthermore the problem of what happens to the creep-strain induced strengthening when the material recovers either at zero or some reduced operating stress has significant engineering consequences. It was for these reasons that the present investigation on the recovery of creep behavior was initiated. Inasmuch as a substantial background has now developed on the creep of high-purity aluminum, this material was again selected for the current investigation. Furthermore extensive evidence is now

Jan 1, 1963

By Floyd E. Bliven

A century ago, Thomas Carlyle sketched the Emblem of the Wasting Candle in one of his papers. "Terar Dum Prosim" he wrote under the candle-" May I be wasted so that I be of use." The application of his reasoning is an excellent guide for a discussion of the scrap problems of today. The General Electric Co. has addressed itself to the need of proper and careful preparation of scrap metals for many years. A supervisor of salvage directs this work in each of the works. Generally he is an engineer and has had broad factory training. He gives general direction to the collection, preparation and disposition of scrap materials. He operates the extensive facilities which each works has provided for the centralization and control of scrap accumulations, and also initiates studies leading to the reduction of scrap accruing from machining and assembly operations. r We recognize that each industry, each factory, each locality faces a different set of conditions. Irrespective of size, in a plant employing 20 men or a large works with 15,00 employees-certain fundamental principles can be applied for organization and the collection of scrap. The manufacture of electrical apparatus is a highly complicated intricate business. In one area we make electronic tube and adjacent buildings house the manufacture of steam turbines. Both are instruments for power-different in size and in many cases serving different fields of application. Unlike the great industries that build automobiles, trucks, or engines where repetitive operations, once solved, set the stage, electrical manufacturers' plants are large jobbing shops. Therefore, we must carefully plan every step in handling the scrap that "in so wasting to produce the finished motor or locomotive-we can return this product to reprocessing and ultimate use." ESSENTIALS FOR SALVAGE EFFICIENCY The essential steps for an efficient salvage department are: I. Selection of Personnel.-An able foreman would be a man of broad experience and understanding-one who commands the respect of the entire foreman group as well as that of his own men. In the interest of clean scrap, it is necessary to acquaint the foremen in the separate manufacturing units with the need of careful segregation in the shop and the best methods of obtaining it. At least 40 per cent contact time should be devoted for this purpose. 2. The physical equipment of the salvage department should be devised and selected to handle complete, at one point, all scrap operations. Bulky materials as produced by some large shops can be economically placed in salable shape at the divisional point. Because salvage

Jan 1, 1943

By R. H. Lynn, T. C. Craig

During the year 1933, in the Texas Panhandle, 113 oil wells were completed, adding 33,337 bbl. to the daily potential of the field. The field potential on Jan. 1, 1933, as determined by the Texas Railroad Commission, was 149,260 bbl., with a daily allowable production of 41,000 bbl. The potential was raised gradually, until on July 16, 1933, it reached 155,344 bbl. with a daily allowable of 55,000 bbl. This potential and allowable was maintained over a period from July 16, 1933, to Sept. 8, 1933, when the potential was reduced to 136,893, with a daily allowable of 43,727 bbl. Since Sept. 8, 1933, there has been a gradual increase, until on Jan. 1, 1934, the field potential reached 159,740 bbl. with a daily allowable of 42,000 bbl. Of this amount 26,429 bbl. arc "marginal oil" and 2682 bbl. are exempt on account of water. Deepening of Wells During the year 64 wells were deepened, increasing their total oil production 9631 bbl. per day. Of this amount the Gray County granite wash contributed 9256 bbl. from 57 wells. It has been found in many places that the granite wash carries an additional oil pay from 50 to 75 ft. below sea level. The majority of the wells that were .drilled during the early development in Gray County encountered their oil above sea level. When the wells producing from the upper horizon have become unprofit-

Jan 1, 1934

By Leslie W. Austin

ROTARY kiln operators will agree that some of the most severe conditions a refractory must stand occur in the hot zone of a kiln burning Portland cement, dead burn dolomite, magnesite, periclase, and similar materials. Frequently the operator is faced with factors beyond his control which drastically shorten the life of refractories. Shutdown due to mechanical failure can be serious if the period is of sufficiently long duration to cause the dropping of coating or the loosening of the lining. A change in slurry can affect the coating and cause ring buildup. A change in type of fuel and its effect upon the flame can cause a shift in location of the hottest zone. Weekend shutdowns or any other interruption can cause the operator trouble and may damage the refractories, since stopping and starting a rotary kiln is certainly more difficult than stopping and starting a motor. Some operators have tried to set an estimate of damage for each shutdown in equivalent days of running time. Conditions affecting the refractory may be roughly grouped in four classes: chemical attack, mechanical stress, thermal shock, and abrasion. Chemical Attack: The drive to obtain maximum production through a kiln demands maximum operating temperatures, temperatures which are limited more by the ringing up or melting of the clinker. This can cause interface temperatures at the junction of coating and refractory which require the use of a basic kiln block to withstand the chemical attack. Chemical changes take place within the refractory itself, especially in chemically bonded or unburned kiln blocks: These changes cause the formation of the ceramic or burned bond. Migrating liquids or fluxes from the kiln charge have an effect within the refractory and lead to mineral or glass formation. The alkalies, sodium and potassium, migrate into the refractory as silicates, chlorides, sulphates or other salts. They may move under capillary action or may be caused to move by volatilization with condensation in the cooler portion. Mechanical Stress: Concentrated stress may be caused by several factors or combinations thereof. 1-The rings of refractories must be kept tight and rigid within the kiln, and this alone demands considerable force to hold the blocks in place. So that the force will not be concentrated, the blocks should fit the circle as perfectly as possible, with the faces in contact overall. 2-As the kiln is heated, thermal expansion takes place at the hot end of the kiln block. Since this disturbs the plane face it too can cause a concentrated stress at the two ends of the block, and shearing stress can be set up within the brick itself because of the difference in expansion between the two ends. 3-If a lining becomes loose and moves in the shell very severe stress can be set up, and as the kiln rotates this load changes and gives the effect of repeated loading. Permanent expansion of the refractory can also cause severe loading. 4-Not least important, flexing of the kiln is frequently the cause of concentrated stresses. Thermal Shock: Thermal shock, the result of heating and cooling too rapidly, occurs on starting and stopping or when a large patch of coating drops, exposing the bricks. Again, its destructive effect is often the result of phase change, liquid to solid or the reverse; dense refractories loaded with glass-forming impurities are particularly susceptible. Thermal shock is a problem with refractories set in the wall or roof of a stationary furnace, and becomes even more serious in a rotary kiln, the tendency to spall being magnified with movement and concentration of stress. Uniform rate of feed and loading insures both better coating and a more uniform stress. Abrasion: If the refractories do not take a coating, abrasion can become a most destructive factor. Movement of the lining in shell or movement of loose blocks causes abrasion, which is also most destructive if the refractories do not take a coating. An analysis of the problem of basic lining for the hot zone reveals, therefore, a number of desirable characteristics: high refractoriness, basic chemical reaction, resistance to spalling, good strength at all stages, ability to take coating, true sizing, volume stability, and abrasion resistance. Increased demand

Jan 1, 1952

By S. Pearson, L. Rotherham

Measurements have been made of the variation of internal friction with temperature for spectroscopically pure silver, and for o series of solid solutions of silver with cadmium, indium, and tin, using a Ke-type torsion pendulum apparatus. Some experiments have also been made to investigate the effect of nonmetallic impurity on grain boundary relaxation in silver. The effect of the alloying elements is to increase the grain boundary viscosity, and to raise the activation energy for grain boundary relaxation from 22,000 cal per mol for pure silver to 43,000 cal per mol for the solid solutions; the same value being obtained, within the limits of experimental error, for all the alloying elements and solute concentrations investigated. Results of the experiments show exactly the same trend as those obtained previously for a similar series of copper solid solutions. They are in agreement with the general theory of grain boundary relaxation developed by Zener and Ke, but do not seem to be in agreement with either of the mechanisms so far put forward to explain grain boundary slip. EXPERIMENTS described in this paper were made as part of an investigation into the effect of alloying elements in substitutional solid solution on grain boundary viscosity, measured by the internal friction method developed by Ke.&apos; The apparatus and experimental procedure have already been described.&apos; Preliminary work was done with spectro-scopically pure silver. Experimental Work Materials Used—All the materials were supplied in the form of % mm diam wire by Messrs. Johnson Matthey and Co. Ltd. The silver and all the alloying elements used were spectroscopically pure. Composition of the alloys is given in Table I. They were all melted and chill cast under the same conditions as the copper alloys. The ingots were rolled to 1/4 in. sq rod with intermediate annealing at 600°C in an atmosphere of cracked ammonia when necessary. These rods were then drawn to wire by standard procedure with intermediate bright anneals at suitable steps in the drawing operations. Specimens from the annealed wires were sectioned longitudinally. mechanically polished, and examined under the microscope. They were then etched and reexamined. Grain sizes were reasonably uniform for all wires, and no traces of a second constituent were observed. The wires were weighed before and after testing so as to measure any loss of the alloying element due to evaporation. The loss was less than the accuracy of measurement—< 0.1 pct of the total weight— for the Ag-In and Ag-Sn alloys, but appreciable loss of weight occurred in the case of the Ag-Cd alloys. The percentage loss is given in Table 11. X-ray diffraction photographs were taken of all thc wires after test to determine whether there was any marked preferred orientation. Results of the examination are given in Table 111. Experiments on Spectroscopically Pure Silver-— Experiments were made on specimens in which the grain diameter was small relative to that of the wire, and on one specimen in which the grains were grown by the usual strain-anneal method to extend across the full diameter of the wire. These large grained specimens will be referred to as single crystal specimens. The wires were annealed for 11/2 hr at 700°C, and experiments were made at two frequencies of vibration, 1.5 and 0.4 vibrations per sec. The variation of internal friction with temperature is shown in Fig. 1. Experiments on a second small grain specimen gave approximately the same results as for the first wire. It will be seen from Fig. 1 that the peak in the curve for the small grained wire, which is presum-

Jan 1, 1957

By Elmars Ence, Harold Margolin

A. J. Goldak and J. Gordon Parr (University of Alberta) —While we appreciate the difficulties involved in any investigation of this system, and we wish to congratulate the authors on their comprehensive efforts, there are several aspects of their paper that are not clear to us. 1) If the 6 phase is, in fact, isomorphous with Ti3Sn, it should not be designated Ti,Al. An 4B structure cannot be isomorphous with an ordered structure of the DO type. Anderko et al.&apos; suggested that the structure be called Ti3A1, and we believe this to be a more reasonable designation. The confusion is compounded when the authors designate the phase Ti3Al—yet the composition limits of this phase (according to their diagram) are approximately Ti,A1 and Ti,Al. Further, while Pietro-kowsky is said to have pointed out that the structure of the 6 phase is isomorphous with Ti3Sn, we understand that this was only a suggestion that was not confirmed. Margolin and Ence do not appear to have presented any evidence to support the suggested isomorphism. 2) In referring to the precipitation observed microscopically during the initial breakdown of high A1 a during quenching, the authors state that "such precipitation is not likely to be detected by Debye-Scherrer techniques". We suspect that if the precipitate was visible by optical microscopy, it must have at least one dimension of the order of 1 or greater, and would therefore be readily detected by diffraction techniques. 3) The authors state: "The basis for this suggestion (that 6 forms peritectically P + L—6) is the observation that the ,&apos;3 + 6 and 6 phase fields were

Jan 1, 1962