Search Documents

By Alfred H. Bell, Virginia Kline

In 1944, Illinois produced 77,413,000 bbl. of oil, or 4.6 per cent of the total for the United States, and continued to rank sixth in the nation in oil production. This represents a decrease of 6 per cent from 1943, when- the total Illinois production was 82,256,000 bbl. This decrease was much less than the 23 per cent decrease in 1943 from production of the previous year. The principal factor in arresting the production declinc, which had been going on since 1941, seems to be the increased drilling that followed the relaxing of the Federal Government's rules in regard to well spacing. The daily average production for 1944 was approximately 212,000 bbl. Daily averages by months were as follows: Jan......... 219,000 July........ 206,000 Feb......... 220,000 Aug......... 211,000 Mar........ 216,000 Sept......... 209,000 Apr......... 211,000 Oct......... 210,000 May........ 213,000 Nov........ 209,000 June........ 209,000 Dec......... 205,000 During the year, 1991 wells were drilled for oil and gas in Illinois as compared with 1791 in 1943, an increase of II per cent. Of the 1991 wells, 430 are classified as "wildcat" as compared with 461 in 1943. Twenty-eight new pools (Table 2 A) were discovered in 1944 as compared with 29 in 1943. Changes in federal drilling regulations, permitting closer spacing of wells, resulted in a drilling program that emphasized development of proved acreage rather than wildcatting. Data on production and drilling by fields are given in Table I; data on annual production and drilling for Illinois, in Table 3. Discoveries Twenty-eight new fields (Table 2 A), 42 extensions (Table 2 B), and 39 additional producing zones in existing fields (Table 2 C) were discovered in 16 counties in Illinois during 1944. Of the 28 new fields, one was abandoned during the year, 14 were one-well fields, eight others had not more than 6 wells, one had 8, one had 9, one had 11, one had 15, and the largest new field, Roaches North, had 28 producing wells at the end of the year. In all, 109 wells were producing in these new fields on Jan. 2, 1945, as compared with 111 wells producing from 29 new fields at the end of 1943. . The average initial production of the discovery wells of the 28 new fields was 129 bbl. of oil and II bbl. of water, a notable decline from the average initial production of 194 bbl, of oil and 15 bbl. of salt water for the 1943 discovery wells. In fields discovered since 1936, the total number of oil wells producing at the end of 1944 was 12,335. Productive Acreage The area of proved production in the new fields (discovered since 1936) increased from 144,335 acres at the end of 1943 to 173,485 acres at the end of 1944 (Table I), an increase of 29,150 acres. Of this increased area, 1720 acres are in fields discovered during 1944 and 27,430 acres are in extensions of fields discovered earlier.

Jan 1, 1945

By Susasn Leiter

THAT oxygen in copper has been a source of trouble is well known and that that trouble has been real in the commercial world has been shown by Fuller.1 Moore and Beckinsale's paper2 at the annual meeting of the Institute of Metals in London, 1921, called forth considerable discussion. Prof. T. Turner expressed the opinion that it was not necessary to have cuprous oxide present in sufficiently large quantities to form either globules or seams in order to produce a bad effect if the copper were gassed. This brought up the question of the solubility of oxygen in copper and the authors desired to know whether there were any evidence of such solubility, because their experience was that whenever there was any oxygen in copper it was present in the form of free cuprous oxide, .which was practically always in the form of globules. Later Hanson, Marryat, and Ford3 stated that for all practical purposes cuprous oxide may be regarded as insoluble in copper. However, they found particles of the eutectic to coalesce to form much larger particles. They suggested that cuprous oxide was actually slightly soluble in copper, for it was diffi-cult otherwise to understand the mechanism by which such coalescence could take place. W. E. Ruder, in discussing that paper, said that his experiments had led him to conclude that a slight solubility must exist to allow for the ready coalescence of oxide particles, but conductivity tests convinced him that that solubility was very small. Nevertheless, there appeared to be a state of admixture of oxide with copper that closely resembled a colloidal mixture which at first was mistaken for a true solution and which usually existed at the grain boundaries.

Jan 2, 1926

By Paul Billingsley

CERTAIN adequately developed mining districts give complete three-dimensional patterns of ore bodies as clusters rising from roots in basement rocks with details controlled by structure of cover rooks. Examples are Goodsprings, Tintic, Bisbee, Leadville, Hedley, Eureka, Ely and Goldfield. In these and others the controlling structures in both basement and cover rock are elements of the neighboring regional structure and have been produced by rock movements in harmony with continental adjustments, which are usually steep tear faults in basement and thrust crumples in cover. Invariably the structures and movements in the districts have long geologic history and result from intersecting or superimposed deformations of different ages. Salt Lake districts show intersecting Uinta and Cordilleran elements; Colorado dis-tricts show intersecting pre-Cambrian and Tertiary elements, and Bisbee shows Tertiary superimposed on final Paleozoic folding. Thus the position of districts has been determined by the patterns of North American orogenic belts, which make cross-roads in Rocky Mountains and blocks of superimposed deformation in Sierra Nevada, northwest Coast and Canadian Coast Ranges. Essential function of repeated deforma-tion is to strengthen rock, as from shale to slate to schist to gneiss, and thus make it competent to carry channels to depth with or without addition of intrusives. The essence of a mining district is the presence of such competent rocks with long-lived, deep, penetrating breaks reopened to permit passage of heat and associated products from depths to surface. It is suggested that melts such as magmas; metamorphism up to and including granitization; alteration, such as orthoclase-quartz or quartz-sericite or garnet, and also mineralization, may all be by-products of such heat escape along channels made by tectonic forces at specific foci.

Jan 1, 1939

By George H. Eldridge

The existence of phosphate of lime within the State of Florida has been known for over a decade; but until the spring of 1887, the extent and value of its deposit.;, possibly with one exception, were unsuspected. In that year Col. T. S. Moorehead, induced by a statement made by Mr. J. F. Le Baron, examined the gravels of the Peace river, recognized the importance of the deposits, acquired such tracts as were regarded as desirable, and established the pebble-phosphate industry, making his first shipment in May, 1888, to the Scott Manufacturing Company, of Atlanta, Ga. The establishment of the pebble-phosphate industry upon Peace river was followed, a year later, by the discovery in Marion county of an entirely different class of phosphate, now commonly known as hard-rock phosphate. This discovery was made early in June, 1889, by Mr. Albertus Voght, in a well which he was sinking upon his place near the site of the present town of Donnellon, about 20 miles southwest of Ocala. To it, more than to any other cause, is due the rapid and remarkable development of the present great industry of the State. It was, however, Mr. John F. Dunn, of Ocala, who turned to advantage the accidental discovery of Mr. Voght. After acquiring a knowledge as to the chemical composition and value of the material, Mr. Dunn and hid associates purchased several thousand acres of land and organized the Dunnellon Phosphate Company for active operations. From Dunnellon as a center, prospecting rapidly extended in all directions, until at the present day important mines have been opened over a well-defined tract more than 200 miles long and about 6 miles wide. This tract lies par-

Jan 1, 1893

By L. W. Saperstein, Y. J. Wang

The development of computer programs to solve complex ventilation networks has reached a point of refinement where these programs become a necessary tool of the ventilating engineer. Such a program is presented. This program has an increased efficiency over its predecessors; it also includes the important facility of fixed quantity branches. This is in addition to the earlier capabilities of free-splitting, internal or external fans, and natural ventilation pressures. The program is written in Fortran IV with double-precision arithmetic and is listed here. Sample problems with input and output are also given. The recent, and presumably continuing, official interest in mine safety is bound to result in more stringent control requirements for ventilation. Anticipating this requirement, the Dept. of Mining, The Pennsylvania State University, has developed a computer program for the solution of complex mine ventilation networks. It is the opinion of this department that the program has sufficient merit to warrant its use in normal industrial operating conditions. Although the undergraduate mining engineering students of this department are routinely trained to use the program, it was felt that this training did not present a fast enough means of dissemination; consequently, this paper was written. The conception of the program is not new;1; however, the present version incorporates features that changes it from a scientific endeavor to a useful operating tool. These features include those of earlier programs, such as free-splitting, external or internal fans, and natural ventilation processes plus the important ability of handling fixed quantity branches, and of increased efficiency giving reduced cost. The facility for fixed quantities will be discussed in more detail. The solution of any network depends upon satisfying Kirchchoff's laws. These state that the sum of flow at any junction is zero, and that the sum of the pressure drop in branches totals the pressure drop in the mesh constituted by those branches, that is that the pressure drop around any mesh is zero. The terminology is derived from Synge," and is, in fact, that used by Topologists. A branch is any airway of uniform characteristics; a junction is where two or more airways meet (the minimum number of two airways is useful for describing the point where a low resistance airway changes into a high resistance one due to some physical constriction); a mesh is a path, along some branches, that returns on to itself, but does not need to traverse the same branch twice in order to do so; and a tree describes all those branches in a network which, while connected through all the junctions, do not form any meshes. Obviously the branches-in-tree are open-ended and can be shown to be one less than the number of junction (J-1). The branches-out-of-tree, also called basic branches, are equal to the number of basic meshes and are M = N — J + 1, where M is the number of meshes and N is the number of branches. The major difference between this network and an electrical one is that the law attributed to Atkinson for pressure drop is utilized rather than Ohm's law. Atkinson stated that the pressure drop (potential) is equal to a resistance factor multiplied by the quantity squared. This is written H = RlQlQ where H is the head loss. Q? is written in this factored fashion so that H will always have the same sign as Q. A negative sign is used to indicate that flow in a branch is opposite to that of its containing mesh. A mesh takes the direction of its basic branch. Utilizing Atkinson's law in Kirchchoff's second law and bearing in mind that the first law must remain satisfied, the program will determine all quantities, or head losses as they are related, for the branches of the network. The program uses a Geuss-Seidel form of in-teration, starting from an arbitrary Q and using a correction factor of the type first suggested by Professor Hardy Cross' that will handle the nonlinear equation of Atkinson's law. A fuller description of the interative process is included in Wang and Hartman.' Iteration continues until the correction factor is less than or equal to a preset error (E) or until a maximum number of iterations (MAXIT) have been reached. Utilizing an E of 50 cfm, sample problems have had rapid solutions. Rapidity of solution is also ensured by the method of selecting meshes and basic branches. This is done by the computer, which chooses the highest resistance branches, fixed quantity branches, and those containing fans, as basic branches. Natural ventilation pressures are handled as fans of constant pressure and may be assigned to any branch. The computer will generate a fan characteristic by polynominal fitting if a few operating points from the desired fan are input. A fan may be placed in any branch of the network, except those with fixed quantities. The strength of the present program over its earlier versions is its ability to handle fixed quantity branches. This means that certain branches can have their quantity determined, or preset, by the ventilating engineer. Operating under this constraint, the program will analyze the network and output the pressure change necessary to achieve this desired quantity. A call for positive head loss would require an auxiliary fan; negative head loss would require a regulator. This represents a powerful tool for the ventilating engineer who must insure that certain quantities of air pass across the operating faces or through working stopes. McPherson6 suggested that a ventilation program would be useful for determining in advance which branches were receiving inadequate air, and that subsequent calculations would then indicate the necessary corrections. The present program makes these corrections. Thus the mine manager can know immediately the consequences of changes to his system;

Jan 1, 1971

By Ralph Hultgren, David W. Mitchell

MAGNESIUM alloys usually are superheated before casting in order to ensure fineness of grain. Superheat temperatures in common use range from 1600° to 1700°F while the casting temperature, which depends upon the mold shape, is usually 200° to 300°F lower. The process of superheating requires considerable time and seriously shortens the life of the iron pots used. Recently it has been reported' that if acetylene, carbon dioxide or natural gas is bubbled through molten electrolytic A.S.T.M. No. 4 alloy at 1400°F. for 5 min., grain refinement equivalent to that of superheating will take place. Addition of certain solids such as graphite or aluminum carbide accomplishes the same results.2 As will be shown in this paper, it is possible to achieve grain refinement in magnesium casting alloys at low temperatures by mechanical stirring of the molten metal for a short time. This process was developed in the course of research work, supervised by the War Metallurgy Committee under the "Restricted" Project NRC-550, for the Office of Production Research and Development of the War Production Board. This paper, based on that work, has been released for publication by the O.P.R.D. MATERIALS AND METHODS The alloys studied were the most common American sand-casting alloys designated as No. 4 and No. 17 by the American Society for Testing Materials. The magnesium used in these alloys was of both carbothermic3 and electrolytic4 origin. Chemical analyses supplied by the producers are shown in Table I. Each heat consisted of approximately 5 lb. of alloy melted in a Tercod crucible. It was refined by fluxing with Permanente No. 7* refining flux at 1300° to 1350°F. After cooling to 1200' to 1250°F., portions of approximately one pound each were ladled into iron crucibles contained in an electric furnace at about 1250°F. The molten metal was covered with Permanente No. 21† covering flux and then heated to the temperature to be investigated. Normally each of the four portions was given a different treatment. In a typical case one portion was stirred vigorously for 5 min., acetylene gas was passed through a second portion for 5 min., a third portion was superheated to 1600°F for 15 min., then cooled to casting temperature, and the fourth was held for 5 min. at the temperature of stirring or gassing without other treatment. Each portion was then cast into one-inch diameter cylinders in three "nonturbulent" molds of identical shape. One mold was made of cast iron and the other two of baked sand. The cast-iron mold and one of the baked sand molds were heated to 360°F., the other baked sand mold was at room temperature. The freezing times in these molds were

Jan 1, 1945

By B. J. Reid, J. N. Greenwood

It has been shown1 that cavities are formed in the grain-boundaries of copper and 70:30 brass (as well as in magnesium) by the application of tensile stresses at elevated temperatures. For a given rate of strain, cavities are formed in brass at a lower temperature than in copper, and they are larger; it was thought that this earlier onset of cavitation in the alloy might be caused by the distortion produced in the metal lattice by the alloying element. If the cavitation is caused by the vacancy-migration mechanism, ' the distortion of the lattice would reduce the energy required for vacancy formation, and thus provide vacancies more readily to assist in the cavitation process. It was decided to study a range of alloys to find out whether increasing amounts of an alloying element would cause any progressive increase in, or modification of, the cavitation in copper. Nickel was chosen for this purpose, since it is soluble in copper throughout the whole range of alloys. A further advantage was its low vapor pressure, which enabled the preparation of the alloys in vacuum and the consequent reduction of their hydrogen content. It has been suggested that cavities may be nucleated by the migration of hydrogen atoms to the less regular atomic spacing at the boundary, and their combination to form molecules. The latter being too large to diffuse back into the lattice, form stable cavities into which vacancies could condense. PREPARATION OF ALLOYS All alloys, ranging from pure OFHC copper to 43.7 at. pct of nickel (carbonyl), were prepared in a vacuum furnace employing high-frequency induction heating. When a charge was melted, vigorous gas evolution occurred initially, after which the pressure was reduced to 10-4 mm Hg, using an oil-diffusion pump. After remaining molten for a further 1/2 to 1 hr to aid degassing, the melt was allowed to solidify in the crucible. In this way contamination by gases evolved from the surface of a separate mold was avoided. The list of alloys prepared is shown in Table I. The percentage of hydrogen present in the OFHC copper was reduced from 0.0054 at. pct to 0.0012 at. pct, as measured by a vacuum-fusion method. The alloys were cold-rolled to 0.03-in.-thick strip, and were homogenized in vacuum for 1 hr at 900°C after every 30 pct reduction. At a thickness of 0.05 in., the strip was held at 450°C for 24 hr under high vacuum (10-5 mm Hg) in an attempt to reduce the hydrogen content still further. Tensile specimens were prepared with a gage length of 1 in., and were finally annealed for 2 hr at 800°C to give an average grain diameter of 0.1 mm. TENSILE DEFORMATION The specimens were deformed in a tensile straining machine operated by a synchronous motor at a constant rate, equivalent to 1.7 pct per hr on a 1-in. gage length. The specimen and grips were contained in a vacuum jacket. A pressure of 10-2 mm Hg was maintained, which was sufficient to prevent surface tarnishing of a specimen held at 650°C for 24 hr. Tests were made between 20. and 650°C and the temperature was controlled to within ±3° over the gage length. The load was measured by the deflection of a cantilever spring. a) Mechanical Properties-The ductility curves shown in Fig. 1 fall into two groups. Figs. 1(a) and (b) for copper and the 5 pct nickel alloy, respectively, show a continuous fall in ductility with a steep fall between 200° and 400°C. Figs. l(c) to (f) show the same sudden loss of ductility between 200° and 400°C. With higher temperatures, however, there is a recovery in ductility values to a maxi-

Jan 1, 1959

By D. E. Pickett, E. G. Joe

In accordance with good industrial practice, Canadian metallic-ore concentration plants have always recycled a high proportion of process water to save reagents, save power, conserve water resources, and to protect the community water supplies, to give only a few reasons. In the last few years there has been awakened public concern for the environment and, consequently, government regulations have been added as additional reasons. Present recycling practices are summarized as a basis for improved plant design and operating procedures and for further research. In addition, an attempt is made to determine why plants do not recycle water in certain situations. Although not all Canadian mills are covered, the many examples given indicate the problems and the effort being made to solve them. Wherever available, the chemical quality of the water and the process requirements are indicated as well as the other parameters affecting water recycling at each operation.

Jan 1, 1975

By Charles W. Sweetwood

THE Western phosphate field, virtually ignored for 40 years, has been undergoing a rapid climb to economic importance. Until World War II there seemed to be no reason for developing the phosphate rock region of the Intermountain Empire. But the tremendously increased demand for food production and the needs of many branches of the chemical industry changed all that. Quite suddenly a report made by the U. S. Geological Survey at the turn of the century became important. The survey showed that 60 pet of the nation's phosphate reserves were in the western phosphate field. Simplot Fertilizer Co. was one of the first to become actively interested in the development of the area. In August, 1945 the company began exploration of the Phosphoria Formation on the Fort Hall Indian Reservation. The result was the Gay Mine, about 18 miles east of Indian Agency Headquarters at Fort Hall, Idaho, developed to supply high grade phosphate rock for processing into superphosphate fertilizer at the company's Pocatello plant. Six ft of high grade oolitic phosphate rock (ranging from 32.5 to 34.5 pet P2O5) were discovered at the base of the Phosphoria Formation by diamond drilling and dozer trenching. High quality and thickness, plus the fact that the formation lay flat and near the surface made strip and open pit mining possible. In one year of mining, starting June 1946, a total of 53,000 tons of main bed oolitic phosphate rock was hauled to Pocatello for processing into supersulphate. The first year's operation was in

Jan 1, 1952

By Thomas Haight Leggett

I.—The Deep-Level Shafts. The gold-deposits of the Witwatersrand (Anglice, " White Waters' Range ") are, as is well-known, more or less parallel and tilted sedimentary beds of quartz-pebble conglomerate impregnated with gold. These beds, however, are locally called "reefs"—a term equivalent in signification to the American "ledge"—and, like the latter, usually applied to lodes, though covering in practical usage all deposits of tabular form. The first developments of the reefs of the Rand were naturally made along their outcrops. Since the mining law of the Transvaal does not confer upon locators the "extralateral right," the property of each locator upon the outcrop or apex ends with the vertical planes drawn through the boundaries of the claim. Consequently those portions of the reefs which lie "on the dip," beyond these boundaries, are separately acquired by locating new surface-claims, and are usually to be mined only by means of vertical shafts, reaching the reefs at considerable depths. The term "deep-level properties " is given to such claims on the dip, and the " deep-level shafts " are the vertical shafts sunk in the hanging-wall of the Witwatersrand reefs, in contradistinction to the incline-shafts almost universally employed on the outcrop-properties. Number and Distribution.—The accompanying diagram, Plate I., shows the number and depth of these deeplevel shafts, completed or under process of sinking, up to January 1, 1900. A number of shafts already located upon new deep-level properties, but upon which no work has yet been done, are not included in this diagram.* Vertical shafts sunk upon outcrop-

Jan 1, 1901

By M. W. Hayward

THE object of this paper is to record and tabulate the data and field observations obtained by the writers and their associates during 10 years of intensive study of lead-zinc deposits in the Cretaceous limestone areas in Northern Mexico, particularly in mines owned by the Cia Minera de Peñoles, S. A. At the El Paso meeting of the Institute in October, 1930, J. G. Barry made the suggestion that a committee be appointed to correlate the ideas and theories which have been put forth by the numerous engineers and geologists who, during recent years, have made a study of the ore deposits in the area under consideration. The first step in a work of this nature would be to record all of the observed facts, and these facts would have to be accepted by those who attempted to formulate a theory of ore deposition. It is with this idea in mind that the writers have described as accurately as possible the actual, observed facts pertaining to the occurrence of the lead-zinc ores in dolomites or dolomitic horizons. By most writers the term "dolomite" is loosely used to designate magnesium-bearing limestones, regardless of the percentage of MgO present. Since no true dolomites exist in the areas to be described, we shall also loosely use the terms dolomite or dolomitic limestone to desig-nate those beds having a magnesia content of 5 per cent MgO or more. For a number of years the writers have been impressed with the fact that in areas where dolomite beds occur a large percentage of the lead ore is found in these beds, in spite of the fact that such beds may be overlain or underlain by pure limestone, which one would assume to be just as favorable for replacement as the dolomite, if not more so on account of its being more soluble in acid solutions than the dolomite. It is true that in some limestone areas, such as the Erupcion-Ahumada districts, Chihuahua, and Providencia, Zacatecas, where no dolomite beds have been found, large tonnages of lead ores have been mined. We venture to predict, however, that had there been dolomitic beds in these areas, the

Jan 1, 1932

By S. Webster, M. Karmis, C. Haycocks

Mining any seam can seriously affect subsequent operations in coal seams both above and below the one being mined. The effect is often detrimental to the recovery, cost and safety of mining the subsequent seams. This paper describes the ground control mechanisms involved in mining through a passive subsided zone or all actively subsiding trough. Data were extracted from case studies, primarily from the Appalachia region, for construction of empirical models to predict interaction problems that can occur in overlying seams. Inner-burden thickness, innerburden lithology, percentage extraction, lower seam height, time and overburden were analyzed to determine their effect on upper seam damage. Magnitude of upper seam subsidence was incorporated, together with a broad classification of rock types, to predict the type and range of damage that can occur in the upper seam. Results are summarized in graphically and nomogram form for use in. engineering design.

Jan 1, 1984

By Jr. Baldwin. William M

WELL known to every metallurgist is the fact that different production schedules will profoundly affect the character of annealed metal strip. Yet the number of conditions [ ] that may be wrought by different combinations of rolling and annealing schedules is so myriad that despite the continual research that is being applied to this subject, the complete picture is not yet known. Copper, like all other metals, during the process of rolling or annealing, develops certain crystallographic configurations which should not be dismissed as being too impractical, for the crystallographic condition existing within the metal is a principal influence upon both the external mechanical properties and the behavior of the material [ ] when it is subjected to such operations as bending, flanging, drawing, and so forth. EFFECT OF ROLLING AND ANNEALING UPON THE CRYSTALLOGRAPHY OF COPPER STRIP The most salient points in the crystallographic reactions of polycrystalline copper to rolling and annealing may be best represented graphically by a "map" such as that given in Fig. I. I. As copper strip is cold-rolled from a randomly oriented structure (pole figure I),

Jan 1, 1942

By Paul G. Raffinot

I. INTRODUCTION We are aware that as a general rule zinc and lead deposits located by the Mediterranean Sea contain important proportions of oxidized ores of lead and zinc (cerussite, anglesite, smithsonite, hemimorphite). Although their economical significance is decreasing in favor of totally sulphurous ores*, la Societe Miniere et Metallurgique de Penarroya and its subsidiaries are still operating four small oxidized ore-bodies in Morocco, Spain, France, and Italy (see Figure 1). Not all of these deposits contain exclusively oxidized lead and zinc ores but also sulphides such as galena, sphalerite, and pyrite. However, the very presence of the oxidized ores gives the treatment methods their characteristics and it is bearing this in mind that we think the description of these four mills worthwhile. Flotation remains the basic process. It uses sulphurization in alkaline medium and long chain xanthate in order to concentrate lead minerals (amylxanthate) and fatty amines (sterarylamine acetate) to concentrate zinc minerals.

Jan 1, 1970

By Robert A. Kinzie

PAGE Introduction.............334 Climate.............335 History............335 Geology.............341 Mining..............343 Shafts............343 Stations and Ore-Bins....345 Levels. Drifts. Cross-Cuts, Winzes. etc........347 Stoping Surface-Pits,......... 351 Underground Stoping........... 332 Chutes. Drilling. etc.....354 Tramming............. 358 Sampling. Maps and Assaying.........360 Labor.............361 Machinery.............362 Milling,..............362 Crushers.............366 Battery-Foundations...........368 Power (Water—Coal)...........373 Methods of Catching the Free Gold...374 Screens..............376 Apron-Plates,.......376 Concentration..........378 Clean-Up,.............378 Labor..............382 Costs..............382 Introduction. The Treadwell Group comprises five mines. four of which are situated on the northeast side of Douglas island. directly opposite the town of Juneau, and one about four miles back of Juneau. These mines are owned by four separate companies. but are all under the same general management. Those situated on Douglas island are : The Treadwell mine. owned by the Alaska Treadwell Gold Mining Co.. the Mexican mine. owned by the Alaska Mexican Gold Mining Co.; and the Ready Bullion and Seven-Hundred-Foot mines. owned by the Alaska United Gold Mining Co. The Juneau mine. owned by the

Jan 1, 1904

By R. M. Keeney

Before the outbreak of the war in 1914, the only electric-furnace smelting plant operating on a commercial basis west of the Mississippi River was an electric pig-iron plant in California; rare metal ores were not smelted, concentrates of molybdenum, tungsten, uranium, and vanadium ores being shipped East for reduction. Practically no chrome ore was being mined, and only comparatively small amounts of manganese ore. Today there are two electric smelting plants in California, one in Washington, one in lowa, and four in Colorado; two plants are under construction in California, and one in Montana. Ores of manganese, chromium, molybdenum and tungsten are now smelted in the West, and although uranium and vanadium concentrates are still shipped to the East, they will probably be treated in western plants in a short time. The four electric-furnace plants in Colorado are listed in Table 1. Table 1.—Electric Smelting Plants in Colorado Capacity. Company Location KilowattB PRoductS Tungsten Products Co........... Boulder 800 Ferrotungsten, ferromo- lybdenum. Boulder Tungsten Production Co .. Boulder 400 Ferrotungsten. Ferro Alloy Co.................. Utah Junction 1200 Ferrochrome, ferrotung- sten. Iron Mountain Alloy Co......... Utah Junction 3000 Ferromanganese. Power for all of these plants is supplied by the Colorado Power Co. The plant of the Ferro Alloy Co., at Utah Junction, contains one 750-kw., three-phase furnace, to which power is supplied by three 250-lrw. transformers, connected /Y to give 129 volts on the furnace cables, the transformer ratio being 13,200 to 75 volts. The furnace operates with an actual voltage of 120 volts, and produces about 3 tons of ferrochrome per 24 hr. from 40-per cent. Cr2O3 ore. The furnace consists of a steel shell of circular cross-section, 8 ft. (2.43 m.) in diameter by 7 ft. (2.13 m.) deep, lined with magnesite, and having three vertical carbon electrodes 12 in. (30.48 cm.) in diameter. A 450-kw. furnace, of the same size as the 750-kw. furnace, is also operated on chrome ore. This furnace is three-phase in appearance, but operates electrically as a single-phase furnace. There are three vertical

Jan 1, 1920

A rotary chambered blasthole technique has initially indicated a 30% overall improvement in drill and blast department productivity. The method, developed at several open pit copper mines in Arizona, centers around a chambering tool that can be used with existing high-speed rotary drills. The "Chamber Maker," manufactured by the Servco Div. of Smith International, Inc., produces an enlarged section or chamber near the bottom of a large diameter blasthole (Fig. 1). This enlarged cavity permits a greater concentration of explosives at the bottom of the blasthole, resulting in better fragmentation and reduced hard toe problems, and also lowers the number of blastholes required to break a bench area, says Servco's Gerald W. Laswell. Cost savings can therefore be achieved in reduced secondary blasting requirements, increased shovel efficiency, and subsequently, less shovel maintenance. All these factors would serve to lower the overall mine cost per ton figure

Jan 3, 1975

SHORTLY after Ambrose Swasey suggested the creation of the Engineering Foundation in 1914, the World War broke. upon the scene. Consequently all eyes were soon turned to national security problems. In 1916 the newly-organized Engineering Foundation and the four National Societies joined with the National Academy of Sciences in establishing the National Research Council. From then until 1923 the Engineering Foundation devoted the greater part of its resources to the support of the Research Council and the Council's division of engineering. Since 1923, how-ever, it has turned to the original intention for which it was created, of cooperating with the national societies in proj-ects affecting engineering at large, though it still retains a connection with the Research Council. Mere enumeration and tabulation of work undertaken can of course lend but a vague idea of actual accomplish-ments. The reports of the Foundation give information of its widespread activities.

Jan 2, 1928

By Richard W. Lodge

Several methods, both wet and dry, for the assay of zinc-box residues from the cyanide process, have been described in recent years, and each of them has been claimed to be superior to all others. In the year 1901, a paper, entitled "Assay of Zincy Precipitates," was published ill the School of Mines Quarterly to the purport that the scorification method for the assay of zinc-box residues was absolutely unreliable. In order to shed light on this matter, the following experiments were undertaken by Messrs. C.B. Hollis and F. D. Kehew, undergraduate students at the Massachusetts Institute of Technology. The zine-box residues used were obtained through the courtesy of Mr. H. R. Batcheller. The samples were very rich and varied greatly in the fineness of their condition. SCORIFICATION-ASSAYS. In the preliminary tests, the charge, which was weighed on a chemical balance, consisted of 0.1 Assay Ton of residues mixed with from 30 to 35 grammes of test-lead and placed in a 3-in. scorifier, over this an additional quantity of test-lead (from 30 to. 35 grammes) was placed for a cover, and borax-glass, varying in quantity from 3 to 15 grammes, was sprinkled over the top of each charge of the various assays for a cover. The charges were scarified in a muffle-furnace heated to the ordinary temperature which is used in scorification; in some cases the door of the muffle was left open, while in others it remained closed. Generally, the charges spit badly, especially in the assays that were made with door of the muffle left open, or in those in which the door was opened too quickly. The results of the preliminary assays showed: 1. That in order to obtain approxi-

Jan 1, 1904

Considerable discussion took place at the June 18th Board of Directors Meeting concerning ways the Petroleum Branch office in Dallas could better serve its members and the essentially Petroleum Local Sections, namely the Delta, East Texas, Gulf Coast, Kansas, Mid-Continent, North Texas, Oklahoma City, Permian Basin, and Southwest Texas. The question of whether decentralization strengthens or weakens the Institute was debated, particularly as to what services could be advantageously decentralized and how both offices could keep informed on their mutual problems. Among other things, it was decided that an Auxiliary Admissions Committee could screen applications from Petroleum members before final action by the National Admissions Committee in New York. Finally it was voted, "That all administrative matters that can be properly delegated to a Branch organization may be so delegated". Final details were approved at the July 16th meeting of the Executive and Finance Committees.

Jan 1, 1952