Search Documents

By R. C. Himes, K. Zanio, J. B. Wagner, J. W. Moody, J. F. Miller, W. Johnson

The recent research with which this paper deals has been concerned with the preparation of pure PbTe crystals suitable for control of radiative processes and othe.v electronic applications. The research has been directed toward the developrnent of methods for the preparation of puve, homogeneous, loul-ca,wier-density PbTe crystals suitable for use in the fabrication of optically pumped and electrically pumped diode lasers. Steps in the preparation of the crystals include 1) purification of the starting materials, 2) synthesis and purification of the PbTe, 3) growoth of PbTe crystals, and 4) adjustt~zertt of composition of the crystals This Paper describes the general preparation procedure employed and discusses some investigntiotzs of purification processes. THE as-received lead and tellurium are nominally 99.999 to 99.9999 pct pure. Assays furnished by the suppliers, obtained by emission spectrographic analysis, show only the presence of about 2 ppm Mg in the tellurium. Such analyses are not very informative, however, since they give no information on the concentrations of normally gaseous impurity elements such as oxygen. Both the lead and the tellurium in the as-received state usually contain appreciable concentrations of oxygen—primarily in the form of oxides on the surfaces of the material. To reduce the oxygen content, the lead is held in the molten state in hydrogen at -700°C for several hours. For this treatment, the lead is contained in a graphite boat which is rf-heated, and the hydrogen is passed through a liquid-nitrogen trap prior to use. Tellurium is subjected to multiple distillation in hydrogen to remove oxygen and other foreign impurities. If, in conducting the distillation, approximately the last 10 pct of the charge at each "stage" is left as the discard cut, purification of the tellurium proceeds as indicated in Fig. 1.l Tellurium used in this work has been distilled two or three times to reduce carrier concentration to about 10" per cu cm. The PbTe is prepared from the purified elements by reacting them in the molten state in sealed, evacuated, or hydrogen-filled silica ampoules. The charge is usually held above the melting point of PbTe (923°C) at 1000 C for 24 hr to ensure that it has been homogenized. Two methods have been employed for the growth of the required single crystals of PbTe: growth from the melt, which will be discussed first, and growth from the vapor phase. Large single crystals of p-type PbTe can be grown readily from the melt by the Bridgman method. For this method of crystal growth, the PbTe is synthesized in situ from proper proportions of the purified elements. Growth (dropping) rates in the range 1.3 to 6.5 mm per hr are employed. Material near the maximum melting composition (about 50.012 at. pct Te) is utilized to avoid composition change on freezing, and thus to obtain crystals of nearly uniform composition. Crystals prepared by use of procedures described up to this point were sufficiently pure and perfect that they could be used for the preparation of laser crystals in studies at Lincoln Laboratory.2-5 ADJUSTMENT OF COMPOSITION Good n-type crystals of PbTe cannot readily be grown from the melt. Further, growth from the melt of crystals of any compositions (n or p type) other than those near the maximum melting composition is difficult because of the large composition changes that must occur on freezing.'" However, melt-grown crystals can rapidly be brought to other desired compositions by isothermal equilibration through the vapor phase with a two-phase Pb-Te stock material, essentially as described by Brebrick and Allgaier.1 The work to be discussed has been concerned with the preparation of n-type crystals; thus, the two-phase stock which was employed contained excess lead, and all ensuing discussion is of the preparation and properties of n-type crystals. The equilibration was designed to the shift composition to the lead-rich limit of stability at the selected temperature. Initial treatment of the crystals at high temperature was employed to minimize the total time required for the equilibration. Final adjustments of the composition and state of the crystals were made by use of low-temperature heat treatment at temperatures in the range 200" to

Jan 1, 1968

By P. Bardzil, J. Gurland

An experimental study of the variation of transverse-rupture strength with composition Anexperimentaland grain studysize has shown that the strength reaches a maximum for values of the mean free path between carbide particles of 0.3 to 0.6 microns. The fracture oforiginates in and proceeds through the carbide grains mainly. Impact strength and hardness also were recorded. MOST of the physical properties of sintered carbides vary linearly with composition. The transverse-rupture strength, however, shows a unique behavior. As the amount of binder metal is varied from 6 to 25 pct by weight, the strength at first increases; then, between 15 and 20 pct Co, it reaches a maximum of nearly 400,000 psi, and finally decreases with further additions of binder metal. This behavior of the transverse-rupture strength has been reported, among others, by Englel and Sandford and Trent.' The significance of these observations has not been discussed in the literature. That it may be of more than specific importance is indicated by the very similar variation of strength with composition encountered in other systems sintered in the presence of a liquid phase, such as Tic-Ni3 and Fe-Cu.' Experimental Details All compacts were prepared and sintered according to normal industrial practice. The average diameter of WC grains and the mean free path between grains were measured on metallographically prepared samples by a method of linear and planar analysis sing the relations where d is the average diameter of dispersed grains; Nl is the number of noncontiguous grains intersected on a metallographic plane by a line of unit length; N, is the number of noncontiguous grains per unit area; P is the mean free path between grains of dispersed phase; and f is the volume fraction of dispersed phase. Approximately 1000 grains were counted on each sample. For each composition d2 was plotted against P, the resulting straight lines serving as a check on the measurements. The distribution curves of the WC powders of different average diameters were homologous, and no attempt was made to influence the grain size by blending powders, adjusting the sintering conditions, or otherwise altering the particle size distribution. Densities were measured by differential weighings in air and water. The degree of densification did not vary consistently with either composition or grain size. The density is influenced by slight amounts of impurities, specifically by 0.1 to 0.2 pct Fe which enters the powders during ball milling. As an illus- -tration of the experimental variations, a number of measured densities are listed in Table I. They are expressed in percentage of theoretical density, as calculated from the published X-ray densities of WC and Co.' For the purpose of determining the transverse-rupture strength, rectangular test specimens (3/16x 3/8x3/4 in.) were broken by loading at the center of a 9/16 in. span. The average strength of five or more samples is reported for each composition and grain size. The compacts were ground on two parallel surfaces only. The load was applied at an average rate of 6,800 psi per sec. Since the elongation after fracture of the alloys is very small, it was assumed that the compacts deform elastically to failure and the fracture stress was calculated by the conventional beam formula. The data for one alloy are presented in Table II as an example of the results and scattering ranges encountered. The precision of the test, as measured by the average difference between duplicates, is of the order of 15,000 psi. The results are strictly comparable only to compacts prepared and tested in the manner described and of similar chemical composition and grain size characteristics. Unnotched Charpy specimens were used for impact testing. Each point represents the average of 3 to 20 samples, the larger number being used in an attempt to determine the influence of grain size. Considerable scatter was encountered, the range from lowest to highest value often amounting to 30 pct of the impact strength. The hardness is reported as a Ra reading, using a 60 kg load with diamond brale indenter. Compositions are given in weight percent.

Jan 1, 1956

By William E. Harris

Time and experience have demonstrated that by means of the Waelz process zinc, lead, cadmium, arsenic, antimony, bismuth and tin can be volatilized satisfactorily. In this way difficult gold ores are being treated to allow for the recovery of the precious metal. Iron ore containing zinc is being treated to remove the zinc and recover the iron. In Germany, thallium is being recovered in commercial quantities from the zinc oxide fume; indium, germanium and gallium are also concentrated to a degree warranting recovery, even though these rare metals are only recognizable in the ore by means of the spectroscope. The physical, chemical or mineralogical condition of the raw material affects very little the applicability of the process. The name Waelz is derived from the German word Waelzen, meaning a "trundling motion," which very aptly describes the movement of the charge through the slowly rotating kiln. The recovery of zinc and lead by volatilization in a rotary kiln has its origin in a process patented in 1910 by Edward Dedolph, of British Columbia. The Dedolph patent was taken over by the Metallgesell-schaft of Frankfurt-on-Main, Germany, which in cooperation with the Griesheim-Elektron, now a part of a large industrial combine, introduced certain improvements (Ohlmer, Specketer patents), but without bringing the process to a state suitable for large-scale operations. The war temporarily stopped all work on the process, and it was not until after the war that the Krupp Grusonwerk, of Magdeburg-Buckau, Germany, quite independently of the Metallgesellschaft, instituted research work in this field of metallurgy, which in 1923 led to the Waelz process proper. The Krupp Grusonwerk and the Metallgesellschaft A.G. later on collaborated, and by their joint efforts further developed and perfected the Waelz process, which they are marketing together as "Waelz-Gemeinschaft." The process is capable of treating a varied type of material; for instance, oxidized and sulphide zinc ores, calamine (zinc carbonate ore) waste dumps, jig tailings, jig slimes, table concentrate slimes, brass ashes, zinc-bearing iron ores (where the iron sinter is the real objective and the zinc oxide a by-product), electrolytic-zinc leach residues, zinc muffle residues and works sweepings, lead-furnace slags, tin ores and slags, anti-

Jan 1, 1937

By Michael Hoch, Walter C. Wyder

The Cr-Ni system was investigated between 900" and 1400°C and 45 to 100 wt pct Cr. The Cr-Fe system was studied between 1200" and 1385°C and 70 to 100 wt pct Cr. Powdered alloy compacts were produced from high-purity chromium, nickel, and iron poulders. The compacts were sintered in an argon atmosphere and then machined into small, 0.030-in. diam cylindrical specimens. These were then heated by induction in the high-temperature X-ray diJfractwn camem under a helium atmosphere and irradiated with copper Ka radiation. From the results of the high-temperature X-ray diffraction patterns it can be concluded that chromium exists only in the bcc form, and that no eutectoid reaction occurs in the Cr-Ni system in the temperature interval 900" to 1400°C. The X-ray diffraction patterns are in agreement with the Cr-Ni phase diagram of Bechtoldt and Vacher, and Williams. It is possible that chromium undergoes one or more allotropic transformations between room temperature and its melting point. Most of the evidence was gathered from the study of the chromium-rich ends of the Cr-Ni and Cr-Fe binary systems. All the investigations rely heavily on indirect methods: thermal analysis, electrical resistivity, and micro-graphic inspection of quenched samples. In the present work the chromium-rich side of the Cr-Ni and Cr-Fe binary systems is studied, using high-temperature X-ray diffraction techniques. Thus the coexistent structures can be observed directly at temperature. PREVIOUS INVESTIGATIONS ~ansenl shows two possible Cr-Ni phase diagrams 1) a simple eutectic [Liquid =a-Cr(bcc) + y-Ni(fcc)], 2) a eutectic [Liquid+ P-Cr(fcc) + y-Ni(fcc)] and euctectoid [p-Cr(fcc) ==a-Cr(bcc) + yNi(fcc)]. The latter is based on the work of Grant and co-workers.2 Stein and rant'" placed the eutectoid composition at 1215°C and 68 wt pct Cr; their diagram is shown in Fig. l. Similarly, Sully3 also discusses the two proposed diagrams. Price and Grant,4 working on an isothermal section of the Cr-Ni- Fe ternary diagram at 1300°C, made no mention of a ß-chromium phase (fcc). The ß-chromium structure was also reported by Misencik 5 in the Cr-Nb(Cb) system. Williams 6 studied the Cr-Ni system using precipitation techniques. His work included the chromium and nickel solvus lines below 1250°C. He reported no ß structure nor any eutectoid reaction. The solvus lines which he produced were very similar to those of Jette, et al 7 below 1000°C. He concluded that Grant and coworkers2 had misinterpreted their data, and that effects which they had reported were actually due to the rapid and extensive precipitation of the nickel-rich phase. Bechtoldt and vacher8 used sintered powdered alloy compacts in an attempt to find the ß phase. They used metallographic and room-temperature X-ray diffraction techniques and also failed to detect the fcc chromium phase. They attributed the low slope of the chromium solvus at approximately 1150°C as the probable cause of the abundant precipitation obtained. They also stated that the precipitation was the probable cause for the abrupt discontinuities in the thermal analysis and electrical resistivity data which led to the conclusion that a eutectoid reaction existed. Fig. 1 also shows their diagram. Grigor'ev and coworkers9 investigated the polymorphic changes of chromium in the Cr-Ni phase diagram. Using standard microstructural and thermal analysis techniques, they published a phase diagram which contained five polymorphic forms of pure chromium and four eutectoid reactions. They stated that the room-temperature bcc chromium transformed to a fcc structure at 930°C, to bcc at 1300°C, to hcp at 1650oC, and then finally to bcc at 1830°C. The eutectoid reactions were placed at 850°, 960o, 1140°, and 1220°C. Also to be noted was the fact that the uppermost phase, the bcc above 1830°C, was different from the upper phase of Grant and coworkers,2 the fcc above 1840°C. Their eutectoid reactions, temperatures and compositions fall

Jan 1, 1963

By R. W. Heckel

The growth and shrinkage rates of second-phase particles of various size distributions are analyzed in terms of five mathematical models. These models apply to various forms of diffusion-controlled growth (one model) and interjace-controlled growth (four models). The expression for diffusion-controlled growth assumes local equilibrium at the interface between the second Phase and the matrix and through the choice of the proper flux area perrnits the definition of minimum diffusion-controlled growth kinetics. The interface-controlled kinetics models consider the situations where the rate-controlling step occurs at either the interlace undergoing solution or the interface undergoing deposition. In addition, each of these interface-controlled kinetics models is analyzed for interface reaction rates which are independent of the thermodynamic activity gradient across the interface or proportional to the gradient. THE variation of the size distribution of second-phase particles in a solute-saturated matrix has been a stimulating topic for many years. Research has been carried out in this area for situations where the matrix was either liquid or solid. It is well-understood that the over-all process results in an increase in the average particle size, a decrease in the total number of particles per unit volume, and a net decrease in surface area. Greenwood1 has presented a mathematical model based upon the mass balance existing between growing and shrinking particles. His analysis is stated in terms of Fick's First Law using concentration gradients set up between particles of different size as a result of the effect of surface curvature on solubility. Greenwood's analysis indicates that the mean particle size should increase approximately as the cube root of time. Asimow2 has shown that several of the simplifying assumptions employed by Greenwood may be eliminated from this diffusion-controlled model with little increase in complexity. Lifshits and Slyozov3-5 have also considered the growth-shrinkage problem involving diffusion-controlled kinetics. Their analysis was extended to include the effects of interacting particles ("kinetic approximation"), particle shape, and elastic strains. These authors also show that the mean particle size varies as the cube root of the reaction time. wagner6 has formulated expressions for both diffusion-controlled kinetics and interface-controlled kinetics in the growth-shrinkage problem. Wagner's diffusion-controlled kinetics is based upon the same form of mass balance using Fick's First Law as used by others and is shown to be applicable to situations where kr >> D (k is the interface reaction constant, r is the particle radius, and D is the diffusion coefficient). This analysis also yields a mean particle size which varies as the cube root of time, in agreement with other workers. Wagner also developed interface-controlled kinetics to handle kr « D. This model was based upon the fact that the interface reaction rate is proportional to the interface area. Wagner assumed that the rate was also proportional to the thermodynamic activity difference, ?a, existing across the interface. Thus, the specific reaction rate at the surface of radius r was defined as k • 4nr2 . ?a. It is the purpose of the present paper to reconsider the processes of diffusion-controlled growth and interface-controlled growth in the variation of particle-size distributions as a function of time at constant second-phase volume. The analyses are formulated in a manner which permits data obtained

Jan 1, 1965

By J. E. Tiffany, S. S. Lubelsky

For blasting in coal mines the U. S. Bureau of Mines recommends that permissible explosives be used exclusively, that these shall be fired electrically, and that where feasible the working place shall be cut or sheared. These recommendations are made to promote safety and prevent mine explosions. Although permissible explosives are not flameless, their lower flame temperature and shorter duration of flanie make their use safer than that of nonpermissible explosives. Mixtures of air with both methane and bituminous coal dust, which are liable to occur in coal mines, may be ignited by coming in contact with any type of flame or spark of sufficient temperature and duration or by the firing of a blast. In a working place where a blast is to be fired, in addition to the use of permissible explosives, adequate ventilation for the dilution and removal of accumulations or outbursts of flammable gas should be provided. Bituminous coal mines should be rock-dusted as a means of rendering the coal dust harmless The efficient use of permissible explosives depends upon the proper preparation of the working place, standardized drilling, the strength characteristics of the explosive, and the use of a proper weight of charge. Experienced shotfirers should load, tamp and fire all holes. The major part of the information and data here presented is based on the results of efficiency tests made in large producing mines of Pennsylvania and Illinois. Bureau of Mines Report of Investigations, Serial No. 2697, describes how a standard method of blasting was worked out and put into operation in a mine in southern Illinois.' This paper contains a description of the methods worked out subsequently in another mine in that district. Descriptions of tests in two Pennsylvania mines are given in Bulletins 11 and 19 of the Carnegie Institute of Technology.2 These tests

Jan 1, 1928

By Stephen Zorn

INTRODUCTION The process of financing mining projects in developing countries has changed greatly in the past 15 years. New methods of financing, notably the use of syndicated Eurocurrency project loans, have appeared, and direct equity financing by transnational mining corporations has become less significant. These changes are of particular importance to developing countries which have many mineral deposits still awaiting development, or even discovery. If major new mines are to be financed, host governments will need to obtain more sophisticated information than has hitherto been widely available as to the various sources of finance currently available and as to possibilities for innovative approaches to financing, such as the combination of several different kinds of financing in a single package. This paper reviews the major sources of mining finance potentially available to developing countries and highlights those problems in obtaining adequate financing that developing country producers have begun to experience in the last few years and that are likely to persist through the 1980s. Section I surveys the major types of mining finance; section II reviews specific financing problems, including (a) the withdrawal of the transnational corporations from developing countries, (b) inflation and the size of new projects; (c) developing country indebtedness, and (d) competition among projects in different countries. SOURCES OF DEVELOPING COUNTRY MINING CAPITAL1/ There is a wide range of financing mechanisms which are potentially available to developing countries with economically viable mining projects., Moreover, these financing mechanisms have not been fully exploited by developing countries, and more aggressive pursuit of financing by the governments of these countries may well reveal greater possibilities in respect of any particular project than may initially have appeared. However, virtually all the funds available from these sources are available only to projects which meet the standards of viability acceptable to lenders and others in the business community. If a project does not, for example, promise to generate a discounted cash flow rate of return of at least 15 per cent on total funds employed, or if it does not appear likely to generate sufficient cash flow in the early years of production to cover debt service requirements with a comfortable margin in reserve, most of the sources of financing will not be available. Only where a government has its own financial surplus (as in the case, for example, of the industrialization program of the Saudi Arabian government) can it effectively undertake projects which do not satisfy the definition of economic viability that is accepted at any given time by the worldwide financial community. Internal Sources In Developing Countries Internal financing capacity in developing countries is restricted to a relatively small number of countries - typically those large enough to support a well-rounded industrial sector, in which mining is only one of a number of dynamic industries. While there are large mining companies in certain other countries, the ability of such companies to finance new projects (or even, in some cases, to generate the cash necessary to maintain existing levels of production) is highly problematical. Within developing countries, the possible sources of internally-generated mining finance are the following: (1) state-owned enterprises; (2) private capital; (3) the banking system, and in particular those financing agencies that have a special involvement with the mining sector; and (4) direct budgetary appropriations.

Jan 1, 1985

By Frank T. Sisco, Selma F. Hermann

gancse constituent in the alpha grains. Nickel produces a structure of alpha plus cutectoid almost identical with that of the normal aluminum bronze (Fig. 38), except for the rod-shaped nickel constituent in the alpha grains. Silicon produccs a light structure with small regular needles, possibly a modified form of beta. Fig. 45 shows the alpha plus beta structure of the normal 10 per cent. aluminum alloy as quenched. Manganese produces large grains of beta with alpha as a tiny constituent scattered throughout the spceimen. Silicon, on the other hand, produces all alpha, with free silicon present. One per cent. iron produces alpha plus beta, with a tiny constituent present in the alpha grains. Five per cent. iron introduces twins in the alpha and a nodular iron constituent in both the alpha and the beta. Figs. 50-58 include the structures of the alloys with 8 per cent, aluminum, tempered at 400" C. and at 650" C. Fig. 50 is the normal structure as drawn at 400" C!. It consists of large grains of twinned alpha plus a very small amount of beta. One per cent. silicon increases the amount of beta enormously, but when tempered at 650' C, the beta degenerates to a hard blue network constituent. One per cent. cobalt results in a structure of exceedingly fine-grained, twinned alpha, heavily mottled. Nickel produces large soft grains of alpha with a dot constituent in some of the grains, when tempered at 650" C. Manganese, when tempered at 400" C. produces alpha grains and shows the decom-

Jan 1, 1931

By S. F. Shaw

The theory that maintaining a high back-pressure on the oil sand lowers the viscosity of the oil has been generally accepted. The theory has also been advanced that lower viscosity permits the oil to be moved through the sand to the well at an expenditure of less gas per barrel of oil than would otherwise be required. It seems reasonable to assume that production of oil at the minimum gas-oil ratio will result in a greater ultimate recovery of oil. During the past five years the writer has acquired data on thousands of tests made on wells to determine the best rate at which to produce them. In the majority of cases reduction in back-pressure did not definitely increase the gas-oil ratio. The information obtained from these tests has raised doubt in the mind of the writer as to the correctness of the theory that lowered viscosity results in lower gas-oil ratios and in higher ultimate recovery of oil. The reasons that explain the results obtained in these tests cannot yet be definitely stated, but the hypothesis is being tentatively assumed that there are other factors which outweigh the influence of viscosity. Energy in Gas Moves Oil to Well The general opinion is that in most cases it is the energy in the gas that moves the oil to the well. In wells flowing naturally it is also the energy in the gas that lifts the oil to the surface. In a flowing well, there are two very distinct operations: 1. Moving the oil through the sand to the well. 2. Lifting the oil to the surface. The more important function of the gas is that of moving the oil to the well. Means for lifting the oil can always be found once it has been delivered to the well. Principles Involved in Lifting Oil A well that flows naturally is the same as a gas-lift well except that all of the gas is supplied by the oil reservoir. This natural flow is subject

Jan 1, 1931

By Allen L. Hatch

A survey of all phases of the world's lead and zinc production in 1968 from ore through to refined metal was conducted by sending questionnaires to individual companies ad the results of this survey are tabulated at the end of the paper. The paper goes on to review changes in the geographical distribution of the world's lead and zinc mine and metal production and in the trading patterns of raw materials, present and future utilization of metal production capacity, developments in metal smelting and refining processes and the growing importance of marketing, product development and research in the 1950's and 1960's.

Jan 1, 1970

By E. T. Turkdogan, W. L. Worrell

The rate of reaction of hydrogen sulfide with ferrous sulfide was studied by measuring the initial rates of sulfidation of iron strips in hydrogen sulfide-hydrogen-argon mixtures at 670°, 800°, and 900" C. The time-dependent surface sulfur activity is derived from the instantaneous rate of sulfidation with the assumption that diffusion in the sulfide layer is in a pseudo-steady state with the gas-sulfide chemical reaction. The rate of sulfur transfer from hydrogen sulfide to the surface of iron sulfide is proportional to the partial pressure of hydrogen sulfide and inversely proportional to the activity of sulfur at the surface of the sulfide layer. The derived rate equation is based on the assumption that most of the surface sites on the chemisorbed layer of iron sulfide are occupied by sulfur atoms and that the slow rate-controlling reaction is the dissociation of hydrogen sulfide on the chemisorbed layer. The experimental results are in reasonable accord with this reaction model. 1 HE slow approach to parabolic growth rate in the sulfidation of iron in hydrogen sulfide-hydrogen mixtures is a manifestation of slow approach to surface equilibrium between the gas and the surface of the sulfide layer. For example, at 800°C and Fig. 7 in Part I, the parabolic growth rate begins after approximately 1 day of sulfidation time. With decreasing temperature and decreasing partial pressure of hydrogen sulfide, the time necessary to reach gas-sulfide surface equilibrium is much longer. These observations are similar to those reported previously by Turkdogan et al.' on the oxidation of iron to wustite in hydrogen-water vapor mixtures. The slow approach to gas-sulfide equilibrium is well-demonstrated by the results in Fig. 1 where the square of the weight gain per unit area, ( g S per sq cmI2, is plotted against time for gas mixtures having PH g//>H = 1.0 with 0, 25, 50, and 67 pct Ar at 800°C. The value of 1.5 X lo-' (g S per sq cm)' corresponds to almost complete sulfidation of the iron strip (- 0.05 cm thick) to iron sulfide. The points fall on S-shaped curves. If the inflection parts of the curves are considered to be linear, thus indicating parabolic growth rate and the establishment of gas-sulfide equilibrium, their slopes would have to be the same for a fixed ratio in the gas mixture. Such is not the case, and the slopes for the "linear" parts of the S-shaped curves are lower than the value when gas-sulfide surface equilibrium is established. The subject matter of this paper is the kinetics of the surface reaction of hydrogen sulfide with iron sulfide during the early stages of sulfidation of an iron strip. EXPERIMENTAL RESULTS The apparatus and materials used were the same as those discussed in Part I. In the present experiments of relatively short duration, a purified iron strip, 5 by 2 by 0.05 cm, which was suspended in the uniform hot zone of a vertical zircon tube, reacted with a flowing gas mixture of hydrogen sulfide-hydrogen-argon. The sample was suspended from a gold chain attached to a calibrated silica spring. The amount of sulfur picked up by the iron, which formed a layer of iron sulfide, was determined by measuring the displacement of a reference point on the silica spring, using a cathetom-eter. In all cases, the degreased sample was first annealed in a stream of oxygen-free dry hydrogen for several hours to remove any impurities such as oxygen, nitrogen, or carbon which might have been present on the surface of the sample.' The rate measurements were carried out at 670°, 800°, and 900° C in hydrogen sulfide-hydrogen-argon mixtures with pH2 s/Ph2 ratios from 4 to 0.1. In a few experiments of short duration no sulfur deposition was observed in gas mixtures with (comments concerning sulfur deposition at high pH s/ph ratios were made in Part I.) Typical examples of the results obtained are shown in Fig. 2 for two temperatures and two gas compositions. With the present experimental technique, reproducible rate data could be obtained only after a uniform

Jan 1, 1969

By W. M. Weigel

The general term "sand" applies to a multitude of similar materials consisting of fine granular mineral. As usually understood, it means the ordinary natural product used for structural purposes and made up largely of grains of quartz. Quartz sand constitutes by far the greater bulk of the production, but there are other grades used for industrial purposes, such as molding sand, glass sand and many others, that may be grouped under the general name of special sands. Under this general group would fall filter sand, sand-blast sand, engine sand, potter's sand, abrasive sands of all kinds, sand for pulverizing, roofing sand, flooring sand, fire or furnace sand, standard sand, burnishing sand, sand for magnesium oxychloride cement-plasters and sand for chemical and metallurgical purposes. Sources of Supply Sand is a widely distributed natural product and even the better grades are low-priced commodities. For these reasons development has occurred near points of consumption where sand meeting the requirements is available. Some special grades, however, cannot be prepared from any sand bed and shipments are often made over considerable distances when the only developed deposit is remote from the consuming center. This is true of filter sand, sand-blast sand, sand for pulverizing and some of the others when chemical purity or grain size, coupled with the need of a properly equipped plant for preparation, are required. New Jersey is a large producer of filter, engine, sand-blast, fire, and pulverizing sand. Pennsylvania, and West Virginia produce special sands for pulverizing, fire sand, abrasive sand, engine sand and sand for chemical and metallurgical use. Ohio produces much sand-blast, fire and abrasive sand, and some filter sand. Illinois and Minnesota produce

Jan 1, 1926

By H. F. Ramstad, F. D. Richardson

The equilibria (a) SiOz +Hz =SiO +H20 and (b) Si + SiO, = 2Si0 have beet1 studied at temperatures of 1425"to 1600°C ad 1310°to 1485°C respectively. The stattdard free energy changes for the tzrro reactions are given by the equatiotts Combination of the results for both equilibria leads to tiotz removes certain anomalies in existing high-terlzperature data for equilibria involving silica and silicon in iron. In many metallurgical processes and in many laboratory investigations silicon monoxide undoubtedly plays an important role. It is unfortunate therefore that wide differences exist between the results obtained by different investigators1-7 in their studies of such equilibria as In an attempt to put our knowledge of SiO on a surer basis, an exhaustive study has been made of equilibria [I] and [2] at temperatures ranging from 1300" to 1600°C. Reaction [I] was studied by measuring the amounts of silica which could be condensed from streams of Hz or Hz + HzO which had previously been brought into equilibrium with silica at temperatures ranging from 1425" to 1600°C. Reaction [2] was studied by measuring the material that could be condensed from streams of Hz or argon which had been brought into equilibrium with mixtures of silicon and silica at temperatures ranging from 1310" to 1485°C. EXPERIMENTAL Materials. The silicon was "superpure" grade and contained less than 0.1 pct impurities. The silica was prepared from pure mineral quartz; this was crushed and treated with concentrated hydrochloric acid to remove particles of iron, washed with water, and finally dried at 120°C. For the hydrogen + silica reaction, the silica was sized to —20+100 mesh. For the silicon + silica reaction, the two materials were ground to a fine powder in an agate mortar. The hydrogen and argon were commercial oxygen-free gases. The gas streams were controlled with capillary flow meters and the volumes were measured by wet gas meters. After passing through the meters, the gases were partially dried by silica gel. The hydrogen for the HZ + SiOz reaction was then passed through palladised asbestos at 300°C and dried with magnesium perchlorate. The efficiency of oxygen removal was checked throughout the experiments by passing the gas over an electrically heated strip of nichrome, used as an indicator as described by Rathman and de itt.' When mixtures of HZ + Hz0 were required, the partial pressures of water vapor (1.8 to 22 mm) were obtained by passing the hydrogen through oxalic acid dihydrateg' lo held at various controlled temperatures, O.l°C, by means of a water bath. The hydrogen for the Si + Si02 reaction was purified by passing it over a mixture of 3 parts of magnesium to 5 of lime heated to 600°."l1 u The argon for this reaction was passed through titanium powder (-3/16 in. + 100 mesh) heated to 900°C. The nitrogen used to prevent the reaction products escaping from the condenser (see later), was deoxidized by copper or iron at 600°C. All these gases were finally dried with magnesium perchlorate. Furnace, Temperature Contr01, and Measurement A molybdenum resistance furnace was used for both sets of experiments. The reactions were conducted inside a high-grade alumina tube, 36 in. long and 1 in. in diam as indicated in Fig. 1. With this arrangement an even temperature zone (2"C) 4 cm long was satisfactorily obtained. The temperatures were kept constant by means of a proportional controller actuated by a Pt-Pt 13 pct Rh thermocouple. This was placed between the two alumina tubes, so that the temperature at the junction was 1400" to 1450°C. Up to 1485"C, the temperatures were measured with Pt-Pt 13 pct Rh thermocouples. For higher temperatures an optical pyrometer was used, this being sighted (through the glass window 1 in Fig. 1) on the end of the alumina tube, that held the SiOz or Si +SiOz mixture, 10 in Fig. 1. The optical pyrometer was recalibrated whenever a change was made in any part of the apparatus situated in the hot zone. Successive readings with the optical pyrometer were reproducible to within 1"C. Equilibrium Apparatus and Procedure. Hydvogen and Silica Reaction. The apparatus is shown in Fig.

Jan 1, 1962

By Oscar Weiss

STILFONTEIN and surrounding areas gave negative results in all prospecting attempts since about 1904 when Goerz and Co., a forerunner of Union Corporation Ltd., first drilled in the region and on the farm Stilfontein. Subsequent efforts by African and European Investments Co. and Anglo American Corp. from 1934-37 were completely unsuccessful. Holes drilled by these companies on the farms Rietfontein, Hessie, and Palmietfontein were stopped in the Lower Witwatersrand system without finding payable reefs.

Jan 10, 1951

By E. C. Wright

The following article is based on observation of college graduates entering the steel industry in technical work made during the Past 25 Years, the first five of which were spent as a college instructor in two engineering schools, and the last 20 in the employ of a large steel company that has hired hundreds of engineering graduates for steel-mill operations. The college graduates encountered during this period have come from many colleges representing schools in Eastern States, Midwestern Universities, many Southern colleges, and many smaller colleges and normal training schools mostly in western Pennsylvania and Ohio. The college training of these students for engineering work naturally has varied widely and the educational qualifications of the entrants have been in many ways different. It was found at an early date that graduates of standard engineering colleges were much more adaptable than graduates in science from nontechnical schools. The engineering students seemed to be more suited to actual work in steel plants and in general were better able to grasp a knowledge of the operations they observed. However, although the graduates of engineering schools have had somewhat better training in physics, mathematics, and engineering, it has been a general and continual observation that most of the students employed have had inadequate training in the fundamental sciences. Since this discussion relates entirely to metallurgical engineers it should be emphasized that students taking metallurgical engineering courses in college seem to be poorly trained in organic chemistry-physics, physical chemistry, thermodynamics, and any higher form of mathematics than simple calculus. It has been noted frequently that young engineers faced with problems in a mill that involve some mathematics generally flounder badly, and that they have little conception of physical chemistry. Another common deficiency lies in the young graduate's lack of knowledge of where to look for the more detailed literature on any subject. He reverts instinctively to some college textbook whose coverage is usually very elementary. It is recommended that such textbooks contain a bibliography of the source literature. and that students be taught to use the original data. Many of the students had had previous courses in college dealing with metallurgical work such as steel melting, metallograhy, etc.r but it was found that their grasp of these subjects was extremely sketchy. It was soon realized that an ordinary engineering graduate could be taught more about steel melting and manufacturing processes in a few weeks in a plant than he could learn in a college course on such subjects. A similar statement may be made regarding the ability of students to conduct laboratory work. Their lack of technique and skill in handling equipment and setting up experiments was soon apparent. It became neces-

Jan 1, 1948

By E. C. Wright

The following article is based on observation of college graduates entering the steel industry in technical work made during the Past 25 Years, the first five of which were spent as a college instructor in two engineering schools, and the last 20 in the employ of a large steel company that has hired hundreds of engineering graduates for steel-mill operations. The college graduates encountered during this period have come from many colleges representing schools in Eastern States, Midwestern Universities, many Southern colleges, and many smaller colleges and normal training schools mostly in western Pennsylvania and Ohio. The college training of these students for engineering work naturally has varied widely and the educational qualifications of the entrants have been in many ways different. It was found at an early date that graduates of standard engineering colleges were much more adaptable than graduates in science from nontechnical schools. The engineering students seemed to be more suited to actual work in steel plants and in general were better able to grasp a knowledge of the operations they observed. However, although the graduates of engineering schools have had somewhat better training in physics, mathematics, and engineering, it has been a general and continual observation that most of the students employed have had inadequate training in the fundamental sciences. Since this discussion relates entirely to metallurgical engineers it should be emphasized that students taking metallurgical engineering courses in college seem to be poorly trained in organic chemistry-physics, physical chemistry, thermodynamics, and any higher form of mathematics than simple calculus. It has been noted frequently that young engineers faced with problems in a mill that involve some mathematics generally flounder badly, and that they have little conception of physical chemistry. Another common deficiency lies in the young graduate's lack of knowledge of where to look for the more detailed literature on any subject. He reverts instinctively to some college textbook whose coverage is usually very elementary. It is recommended that such textbooks contain a bibliography of the source literature. and that students be taught to use the original data. Many of the students had had previous courses in college dealing with metallurgical work such as steel melting, metallograhy, etc.r but it was found that their grasp of these subjects was extremely sketchy. It was soon realized that an ordinary engineering graduate could be taught more about steel melting and manufacturing processes in a few weeks in a plant than he could learn in a college course on such subjects. A similar statement may be made regarding the ability of students to conduct laboratory work. Their lack of technique and skill in handling equipment and setting up experiments was soon apparent. It became neces-

Jan 1, 1948

By S. P. Kinney, A. J. Boynton

THIS paper is not the result of recent research with regard to any particular feature of iron metallurgy, blast-furnace practice or mechanical engineering. It is rather a series of notes with regard to contemporaneous progress in blast-furnace construction and operation, together with some suggestions as to changes and improvements that seem to be desirable. On April 1, 1930, a committee of the Chicago District Blast Furnace and Coke Association presented to that association a rather ambitious study of blast-furnace equipment, together with recommendations for the design of construction of a complete blast-furnace unit for the production of 1000 tons of pig iron per day. This report represented the result of months of study by members of the committee, all of whom were actively engaged in operation or design of blast-furnace plants. It is natural, therefore, that comments on the present state of the art should take this 1000-tons furnace, as recommended by the Association, as a basis for comparison with corresponding features of construction or design. See Table 1. In looking through this report at the present time, the significant difference is in the nature of the gas-washing equipment that today would be specified. In other respects, the installation would remain generally very much as it was outlined in 1930. The change in furnace dimensions would be very slight and of no especial significance, except with respect to changes in stock-line diameter, of which more will be said hereafter. The high-efficiency stove as developed by various designers is thoroughly described within this report, and few changes have taken place since. Blowing equipment shows refinement and reflects the improvement in steam engineering. Hoisting and charging equipment and ladles for the conveyance of iron and slag remain, in general, as they were in 1930. In accordance with a general tendency

Jan 1, 1935

By S. W. Zanolli

The history of labor relations in the coal industry of the United States is a study of its collective bargaining. This study of collective bargaining is largely the history of the United Mine Workers of America and its contractual relations with the various coal mining employers who have produced this country's coal over the years under a free enterprise system. There have been other unions in the picture from time to time and some coal miners have mined coal without representation by any union. Even today some 25% of the nation's coal is produced outside of the collective bargaining relationship with the UMWA. However, more than 100,000 coal mine wage employees - well over 75% of the total in the industry - are covered by labor agreements negotiated for them by the UMWA. Practically all of these work in bituminous mines.

Jan 12, 1972

By Henry U. Ross

The behaviour during reduction of iron-ore pellets and sinters was investigated. Several methods for the preparation of agglomerates and their reduction were tried. Commercial agglomerates from world-wide sources as well as experimental samples were tested. The effect of coke additions to pellet and sinter plant feeds was given special consideration. An analysis of the test results has helped to explain many of the phenomena associated with the reduction of iron-ore agglomerates such as swelling, loss in strength and wear resistance, changes in porosity, changes in mineralogy and the formation of metallic iron and slag. A double-layer pellet with all of the coke concentrated in the core proved particularly interesting. Although large quantities of coke showed that partially reduced agglomerates containing metallic iron could be produced in the laboratory, the problem of producing reduced pellets and sinters by the existing agglomerating processes still remains.

Jan 1, 1977

By Paul M. Tyler, Herbert R. Mosley

Strategically situated in almost the heart of the leading fertilizer-consuming area of the United States, Tennessee long has ranked second only to Florida as a phosphate-producing state. Since 1932 its share of the national output of phosphate rock has increased steadily, and in 1937 its production mounted to an all-time record. More significant even than the increase in tonnage are the forward strides in technology. The Tennessee Valley Authority's research program has led to quasicommer-cia1 operations using hydroelectric power to manufacture concentrated phosphatic fertilizer that is used to further the farmer education program designed to streamline the fertilizer business and halt the appalling waste of farm land by soil erosion. Even more stimulating to chemically minded imaginations is the production of elemental phosphorus by a private company that not only has succeeded in extracting it from the phosphate rock in electric furnaces but actually has contrived to capture it and to transport it safely in tank cars. New values have been created for low-grade phosphate deposits, and the economic life of reserves has been lengthened while the waste of former years goes back into the mills for recovery of its values by modernized methods. Tennessee's phosphate-mining industry dates from the discovery of blue rock in Lewis County in December 1893. Its known reserves are of the order of 101,500,000 tons, which compares with the production of 825,099 tons in 1937; that is, 21 per cent of the phosphate-rock output of the whole nation. The total output reported from 1894 until July 1. 1938, was approximately 19,000,000 tons. Offcial estimates of reserves are overly conservative and evidence submitted before a joint Congressional committee in November 1938 places "probable" reserves at more than 6,000,000,000 tons.

Jan 1, 1942