Search Documents

By Harry C. Gatos, Frank J. Bachner

It was shown through high-pressure experiments that tin loss by volatilizatim is necessary for the degrada-tion of the superconducting transition temperature of Nb,Sn associated with high-temperature annealing. Crystallochemical analysis of the degraded Nb3Sn showed that it constitutes a new phase with ordered niobium-site vacancies, created by the migration of niobium atoms to vaccnt tin sites. This new phase was found to form when 4 pct Nb-site vacancies were present. It has a transition temperature of 6'K and a lattice parameter of 5.283A. A similar degradation effect was observed in Nb,Al. Its superconducting transition temperature dropped from 16.5" to 8" K following a high-temperature annealing. The superconducting temperature degradation in these 0-tungsten structure compounds is attributed to the disruption of the interchain d bonding by the periodic interruption of the niobium atom chains. By annealing the degraded Nb, Sn at 1000 C in nitrogen its normal superconducting behavior is restored most likely due to the incorporation of nitrogen atoms causing the elimination of the ordered vacancies. HANAK et al.' have observed low superconducting transition-temperature values (T, - 9"K) in some NbsSn samples deposited from the vapor phase. They attributed such low T, values to disorder in the 0-tung-sten structure. Much lower T values (down to 5.6"K) were reported by Reed et al.zC for NbsSn samples annealed at high temperatures. These authors also attributed this degradation effect to disorder (random occupation of the A and B sites by niobium and tin) but pointed out that such disorder could be brought about (by high-temperature treatment) only in samples containing niobium in excess of the stoichiometric composition NbsSn. Both groups reported that the normal superconductivity behavior could be rever-sibly restored by appropriate heat treatment. Courtney et al., also found that degradation in NbsSn requires excess niobium brought about by the loss of tin during the treatment. However, these investigators proposed that the degradation is due to niobium-site vacancies resulting from the migration of the niobium atoms to the vacated tin atom sites. They did not consider the reversibility of the effect. The present study attempts to establish the nature of the above degradation phenomenon. EXPERIMENTAL PROCEDURES All compounds prepared for this investigation were made from the powders or filings of the elements which were intimately mixed, cold-pressed into a cylindrical pellet at approximately 50,000 lb per sq in., and then submitted to the desired heat treatment. The samples annealed under high pressure were placed in a MgO sample container which was mounted in a pyrophyllite tetrahedron designed for a tetra-hedral-anvil press. Details of the experimental arrangement are given elsewhere. This setup allowed heating at 1800°C or above under pressures in excess of 30kbars for 3 hr. The samples annealed in a vacuum were prepared in a high-temperature vacuum furnace which could reach temperatures up to 2400°C under a pressure of 2 x lo-' Torr. For annealing in a reactive atmosphere, a quartz tube was placed in a clamshell furnace and the desired gas ambient passed through the tube. Lattice parameters were determined using a Debye-Scherer 114.6-mm camera. Cohen's method, programmed for the IBM 7094 computer, was used to calculate the lattice parameter from the measured d spacings. X-ray integrated intensity measurements were made on several samples. These samples were ground to -400 mesh and the powder mixed with a solution of collodion in amyl acetate. The mixture was poured into a depression milled in a bakelite disc. When the mixture dried, the surface of the disc was ground flat leaving a diffraction surface defined by the face of the disc. The disc was mounted in a Philips rotating specimen holder which allowed the rotation of the sample in the plane of the diffraction surface and the integrated intensity measured using a scintillation counter and a pulse-height analysis sys-tem. The superconducting transition temperatures were determined by means of self-inductance techniques.' EXPERIMENTAL RESULTS AND DISCUSSION The Role of Tin Loss in the Degradation of Super-conductivity. The loss of tin during high-temperature annealing can be effectively suppressed by annealing under high hydrostatic pressures. Accordingly, a series of experiments were performed under pressures of approximately 30kbars. This pressure was the minimum under which high-temperature experiments could be safely performed in the particular pressure apparatus employed. Experiments were also designed to test high-pressure effects on the superconductivity behavior of NbJSn. The results of the high-pressure annealing experi-ments are summarized in Table I. All samples were prepared as described earlier. They were reacted and homogenized at 1000°C for 24 hr under argon at-

Jan 1, 1967

THE primary interest in the subject of this chapter lies in the fact that various heats of steel made to the same chemical specification do not always have the same properties. The properties considered here, of course, are those inherent in the ingot immediately after solidification and not qualities imparted by variations in subsequent mechanical or thermal treatment. The expression "made to the same chemical specification" is used because some of the variations in properties are due to variations in chemical analysis within the specified ranges of those elements commonly specified and determined. Other variations in properties are due to variations in those constituents of steel (elements or compounds) that are not ordinarily included among the elements specified, thus not a part of the specified "composition." The term "constitution" is used to include not only the specified composition but also the nature and distribution of every element or compound contained in the steel entering the ingot mold ; also included are items such as aluminum oxides and nitrides, presence of soluble gases, and dispersion of nonmetallic particles. When it is considered that the constitution of steel is determined by the addition or absorption into the bath of all such constituents from whatever source, it follows that constitution is of necessity the final result of steelmaking practice. It is the agency through which steelmaking practice operates to control the properties of the steel. The term steelmaking practice is here used in the broad sense, meaning the control of all the materials entering the steel and of the conditions under which the process is carried out. Steelmaking practice, thus defined, establishes the chemical system within which the reactions between components must proceed in obedience to the laws of chemistry. Thus the chemical constitution of the steel is established and, through constitution, the properties of the metal are established. In the preceding chapters it has been shown how the constitu-

Jan 1, 1964

By J. D. Price, G. V. Woody

MANY producers of by-product coke have spent considerable time and given considerable thought to the use of a substitute for low-volatile coal as an admixture with high-volatile coking coal for charging high-temperature by-product coke ovens. Generally speaking, there are two principal reasons for this, one being occasioned by the lack, in certain localities, of low-volatile coal delivered at a cost sufficiently low to permit its use, and another being the desirability of finding a substitute product with a delivered cost lower than the cost of the low-volatile coal. It was for the first of these reasons that the Colorado Fuel and Iron Corporation was particularly interested in this subject. This paper deals with the experimental work and the results obtained by that company in producing and using low-temperature char. OVERCOMING DEFECTS IN COKE FROM COLORADO COALS Colorado coking coals are all of the high-volatile type and were all laid down during he Cretaceous period, which makes them something like 80 million or so years younger, geologically, than eastern coals. They behave, when coked alone, something like the Pittsburgh-seam coals. They make a very brittle, highly cross-fractured, fingery coke of fair shatter value but quite low in resistance to abrasion. Mixed with a low-volatile coking coal such as Pocahontas or certain Oklahoma coals, they make a coke that is equal to virtually any of the eastern cokes. The inferior quality of Colorado coke has long been recognized, and a considerable amount of time, effort and money has been spent upon investigations of means for improving its physical properties. While it has been found that some improvement in quality of coke can be secured by the adjustment and control of such variables as pulverization, moisture content, oven temperature and bulk density of charge, and through the addition of certain inert materials such as pulverized coke breeze, pitch, high-volatile noncoking or semicoking coal, the benefits so gained have been comparatively small. There are no low or medium-volatile coking coals available within a reasonable freight-cost distance. Therefore a substitute for low-volatile coal was developed through low-temperature carbonization-or, more correctly speaking, through the partial devolatilization-of high-volatile coals. The blending of this lower volatile char with the high-volatile coking coal distinctly improves the quality of coke made from Colorado coal. There is nothing especially new about this idea. In 1908 a Japanese patent was taken out by Kotaro Shimomura, whose claim was: The method of making a nonfingery coke out of bituminous coals, without using natural coals of low-volatile matter; according to which a certain coal is heated at a temperature between about 300°C. and about 600°C. so as to leave about 15 to 25 per cent volatile matter in the coal; this coal is mixed with the

Jan 1, 1944

By J. R. Thompson

It is common practice, and certainly good business as all of us know, to take care of plant operating equipment. Machinery of any type requires periodic inspection and planned maintenance. With this thought in mind a plant operator should at the end of every shutdown period make regular belt inspections and plan for later appropriate care and maintenance. The points mentioned below are understood well by all of us but are sometimes forgotten because belt conveyors are comparatively easy to operate. Maintenance of any conveyor belt is dependent upon the fundamental characteristics of the two component parts-cover and carcass.

Jan 6, 1950

By A. Aly Selim, Bruce D. Hanson

A computer model capable of simulating the basic production system in a variety of underground mining methods has been developed at the U.S. Bureau of Mines Twin Cities Mining Research Center. The simulation of the basic production system at the working face, which includes drilling, blasting, mucking, and roof bolting, is described in this paper. The model is event-oriented; that is, the status of the system is updated at the occurrence of an event. All event or activity times, including failure and repair of equipment, are treated as stochastic variables. A location dimension, in addition to the time dimension, is used, allowing the simulation of systems with a number of stopes or faces. To aid the user in determining the efficiency of his system, the model provides several reports. An event or activity report gives the frequency of occurrence, total active time, and cumulative delay statistics for each event. An equipment report delineates the availability and utilization of all equipment. A production report provides information on various performance measures such as tons produced and holes drilled. The cost report gives the cost of various elements in the system. Operating data from an actual mining situation were used in validating the model. In addition to the description of the model, examples of simulation experiments which were performed on a room-and-pillar mine system are given. Use of the model to determine methods for improving the efficiency of the system is discussed.

Jan 1, 1976

By C. J. Rosa, W. C. Hagel

An attempt is made to determine the diffusion coefficients of oxygen ions in hypostoichiometric zirconium oxide. A phenomenological theory is developed for three-phase, unidirectional volume diffusion of a gaseous species from a planar source. Knowledge about oxygen diffusion in a and ß zirconium and experimentally measured rates of movements of interfaces permit the evaluation of oxygen ion diffusivi-ties in ZrO2-x. The results conform to the relationship: sq cm per sec, for the temperature range of 875" to 1050° C. DIFFUSION coefficients of oxygen ions in stoichio-metric oxides have been studied by many investigators. The obtained results not only supplement the knowledge about the lattice-defect structures of oxides and conduction mechanisms but also provide information of technological importance. Rate processes such as oxide sintering, high-temperature creep deformation, and oxidation of metals and their alloys are directly dependent on diffusion phenomena. Unfortunately, diffusion coefficients obtained from studies on stoichio-metric oxides cannot be treated without restraints when applied to oxidation kinetics, if precise evaluations of oxidation rates are desired. Oxides formed on metals are usually nonstoichiometric and exhibit nonuniform distribution of either cation or anion vacancies across their thicknesses. Debuigne and Lehr1 extended Danckwerts'2 mathematical analyses and furnished a semitheoretical treatment for evaluating oxygen diffusion coefficients in zirconium oxide in terms of weight gain measurements during oxidation of zirconium in the temperature range 400° to 850°C. Their calculations are based on theoretical partitioning3 of the total amount of oxygen between a zirconium and its oxide phase. An inherent discrepancy appears to continue throughout their calculations. The amount of oxygen confined to the oxide phase should be corrected by multiplying the calculated oxide thickness by the inverse of Pilling-Bedworth ratio, if expansion of zirconium dioxide is taken into account. The purpose of the present investigation is to provide a new semitheoretical treatment for evaluating diffusion coefficients of moving species in hypostoichiometric oxide. The analyses are relevant to unidirectional volume diffusion. Although the presented method is quite general, its applicability will be discussed in terms of kinetic measurements from oxidation of zirconium at temperatures above the a/ß transition, for reasons stated in the later part of this paper. EXPERIMENTAL Pure, 99.93 wt pct, zirconium samples of approximately 2 by 1 by 0.35 cm were exposed to oxygen for various times at four temperature levels: 875°, 950°, 1000°, and 1050°C. High-purity, better than 99.9 vol pct oxygen was passed through a cold trap and columns containing anhydrous CaSO4 to remove residual water vapor. Before exposing to oxygen at a pressure of 500 Torr, specimens were subjected to wet abrasion on 200- through 600-grit Sic papers and polished with 1—p diamond dust. Prior to oxidizing, all zirconium samples were vacuum-annealed at 10-6 mm Hg for about 15 min at the test temperature. The temperature variation across the uniform heat zone was ±2°C from the preset value. Final polishing, for phase thicknesses measurements, was performed by using 8- and 1-p diamond dust and followed by vibrator polishing with 0.05-µ ? Al2O3 solution. Measurements of phase thicknesses were made by projection on a metallographic viewing screen. Conventional powder X-ray analyses for the oxide were employed. RESULTS Fig. 1 is an example of the cross section of oxidized zirconium. Designations of phases given below this figure are the same as those used in the three-phase diffusion system represented by Fig. 5 in the following section. Zirconium oxidized for longer exposure times showed two types of oxides: white oxide at the surface and an underlaying layer of gray oxide. X-ray powder patterns of these oxides at room tern-

Jan 1, 1969

By R. L. Slobod, C. Gatlin

This .study defines the basic mechanism of the mis-cible displacerrzent of oil and writer from porous Medici by various water-driven alcohol .slugs. Three distinct alcohol slug processes were .studied. Considerable data concerning the quanity of alcohol required for oil recovery were also obtained. All data were obtained in a 1-in. diameter, 100-ft long, unconsolidated core. The porosity of this system was 35 per cent. and the permeability was approxitrlately 4 darcies. Total core pore volume wax 5,716 cc. All displacements were conducted at a constant injection rate of 5 to 6 cc//min, which corresponds to a frontal advance of 5 ro 6 ft/hr. The first portion of this paper is concerned with 111 use of one alcohol—isopropyl—a\. the slug material. Isopropyl alcohol (IPA) is completely miscible with both oil rind water; however, miscibility of the threc-component systems, oil-water-IPA, requires a relutively. high concentration of IPA. Hence, the displocement is not of the misoible type unless the IPA concentration is maintained above some critical value. A slug of IPA equal to only 13.5 per cent of the pore volume was jound to be sufficient to obtain complete recover?, of residua1 naphtha. In later studies two distinct process variations were developed. The firsr of these utilized methyl alcohol (MA) and IPA as slug materials. It was shown that methyl alcohol may he substituted for IPA at the front and rear of the slug with no loss of oil recovery. A .slug of 4 per cent MA-4 per cent IPA-4 per cent MA was sufficient for complere oil recovery. Because MA is considerably cheaper than IPA, this represents an important step toward economic application. A .second process variation used normal butyl alcohol (nBA) and MA as the composite slug, the nBA segnzent being injected first. This technique requires the smallest total slug size (approximately 10 per cent) of all processes studied. The high cost of nBA, however, precludes commercial application. It is possible that this basic process, subject to changes of alcohol type, may lead to a commrercicil process. INTRODUCTION Within the last 10 years, considerable study has been devoted to the general mechanics of miscible phase dis- placements in porous media. These studies have. in general, dealt with two-component displacernent. All reported field trials to date have been modified gas drives of one type or another. These utilize either lean gas at high pressure, rich gas at lower pressure or an LPG slug. The irreducible water content of the reservoir remains immobile during these processes. Although these techniques hold great promise. certain drawbacks do exist. Poor areal sweep efficiency, inherent in any displacement having a highly unfavorable mobility ratio, is one disadvantage. Furthermore, the miscibility of all processes which use gas is dependent on pressure. These pressure limitations may prohibit application to shallow reservoirs. There are also many areas where large quantities of LPG and natural gas are not readily available. These factors emphasize the need for improved techniques. The alcohol slug process is also a miscible-phase displacement process. It differs from the previously mentioned two-component techniques, however, in that both the reservoir oil and water are displaced by the slug. This behavior is a consequence of the miscibility of certain oil-water-alcohol systems. In the simplest case, a relatively small volume (slug) of an alcohol (such as isopropyl) is injected into the system. Water is then used to drive the slug through the medium. Thus. three components—-alcohol. oil and connate water-—exist at the front side of the slug. Miscibility is obtained at some alcohol concentration, this being dependent on the solubility of the particular system. Miscibility is maintained within the slug until the alcohol concentration falls below that value required to maintain miscibility. When miscibility is lost, the process reverts to a water flood. Certain inherent benefits of this technique are apparent. High pressures are not necessary to obtain miscibility in these liquid systems. Furthermore, water is a more desirable driving agent than gas because of the improved mobility ratio and the attendant improvement in areal sweep efficiency. The main disadvantage is, of course, the relatively high cost of alcohols. The use of an alcohol slug to recover reservoir oil is not a new idea." ' However, this process has received only limited study, presumably due to the lack of industrial interest caused by the seemingly prohibitive cost of alcohols. The main purpose of this study was to investigate the mechanism of the displacement of oil and water by various alcohol slugs and to develop process modifications aimed toward possible commercial application.

By Zay Jeffries

TUNGSTEN has the highest melting point of all the known metals, namely 3350° C.; it is one of the hardest of the metals; it has the highest equiaxing or recrystallization temperature after strain hardening, of any pure metal known. It is particularly distinguished because, when composed of small equiaxed grains, it is extremely. brittle and fragile at room temperature, and when possessing a fibrous structure it maybe ductile and pliable at room temperature. The common ductile metals act in exactly the opposite manner in this respect. The present paper will include a brief note regarding the manufacture of wrought and. ductile tungsten. The metallography of wrought and ductile tungsten in the various stages of manufacture will be considered more or less in detail. The general relationships between the properties of tungsten and other metals will also be considered. A discussion will be given explaining why fibrous tungsten is ductile at room temperature, even though past experience with other metals would indicate that it should be brittle. Finally, a brief note regarding some new fundamental metallographic propositions relating to all metals will be given.

Jan 6, 1918

By Michael Perch, Charles C. Russell

Nearly 95 per cent of the total coke production in the United States in 1940 was consumed in blast furnaces. In 1939 the percentage was 69,9, and in 1938 it was 61.3, To produce a net ton of pig iron 1959 lb. of coke was required in ,1940 and 1760o lb. in 1939. These figures indicate how dependent the production of pig iron is upon the production of coke. The rate of iron production is in some measure influenced by the physical and chemical characteristics of the coke. Blast-furnace operators believe that the physical properties of coke profoundly influence the operation of the furnace. Although it is true that coke of a wide variety of physical properties is used in American blast furnaces, the periodic fluctuation of these properties is one of the causes of irregularity of blast-furnace operation. The purpose of this paper is to present a broad picture of the physical properties of by-product coke that are generally considered to be important by coke-oven and blast-furnace operators. Effects of the kind of coal used, the preparation of the coal, the rate of coking, and other factors will be considered. Of all these variables, the kind of coal used is by far the most important. In this discussion use will be made of the method of coal classification by rank1 standardized by the American Society for Testing Materials. Although this method of classification has been an American standard for several years, it has not been given the attention it deserves, especially in connection with the selection of coal for production of coke. Despite the fact that many producers of blast-furnace coke are limited to some particular source or sources of coal, a good understanding of the principles involved in setting up the standard method of classification may lead to a better appreciation of the causes of changes in coke characteristics. Furthermore, where it is necessary to select new coals as a substitute for the original supply, this method of classification can be of great assistance. The data presented have been gathered from many sources, but no attempt has been made to cover the vast literature. Instead, some of the more important data have been selected to show how coals and their carbonization affect some of the physical properties of coke. It must be emphasized that generalizations concerning the behavior of coking coals are presented and that individual coals may vary widely from the specific behavior depicted. Nevertheless, it is believed that the data illustrate certain typical behaviors. Neither was it possible to cover completely all the factors involved; for example, the macroscopic constituents of coal are believed to have important effects on the physical properties of coke, but since there is little information available for such study, and since vitrain, clarain, and durain are neither

Jan 1, 1942

By A. F. Witt, A. M. Gaudin, A. K. Biswas

Finite contact angles in the rutile-water-organic liquid system are traceable to contamination or are due to addition of a surface-active agent. Finite contact angles are invariably accompanied by hysteresis.1-7 Besides surfactant concentration and pH, the nature of the organic liquid is found to be a factor influencing the magnitude of contact angle hysteresis. In a recent paper the authors have reviewed principles and applications of measurement methods for contact angles and their hysteresis.22 In this paper, these methods are applied to a system consisting of rutile, an organic liquid (benzene, decane, or dode-cane) and water. Surfactant (dodecylamine hydro-chloride) was used at various concentrations and various pH values. MATERIALS A synthetic rutile crystal supplied by the Linde Co. was used. It is a cylinder 1/2 in. diam, with faces cut perpendicular to the c-axis. The crystal is stated to be alumina-free and to be 99.9% pure. Rutile is a high surface energy solid, its calculated average field strength being 2.7 x 105 e.s.u.,9 its dielectric constant10 is 114. The zero point of charge of rutile was measured11 and found to be at pH 6.0. The atomic distances and bond angles of the tetragonal crystal of rutile have been precisely determined.l2 The organic liquids were specially purified. Reagent grade benzene was repeatedly shaken with concentrated sulfuric acid to remove thiophene, then neutralized with sodium hydroxide solution, rinsed with distilled water, dried overnight over anhydrous calcium chloride and filtered. The refractive index of this chemically purified benzene was 1.4977 (at 25°C) - very close to that of pure benzene (n25 1.4979).13 Both n-decane and n-dodecane were washed with aqueous sodium hydroxide, concentrated sulfuric acid (repeatedly, until the acid layer was colorless) and again with alkali, to free the organic hydrocarbon from fatty acids and unsaturated hydrocarbons. The organic phases were subsequently washed with distilled water and dried over anhydrous sodium sulfate. The filtered hydrocarbons were then distilled under vacuum (9-10 mm pressure). Decane, thus purified, showed traces of unsaturated and of carboxylic compounds. On gas chromatographic analysis the purified n-dodecane showed the presence of two impurities. However, the relative retention times of these components did not change substantially when measured on a polar or a nonpolar column. This indicates that the compounds were probably in the same polarity class, i.e. the components were nonpolar like dodecane. Conductivity water has always been one of the liquids. Conductivity of the water used was 10-6 ohm-' cm". Dodecyl ammonium chloride was prepared from pure amine (supplied by Armour and Co., Chicago), by Li in the MIT Mineral Engineering Laboratory.14 The critical micelle concentration at 25°C is known, 0.0138 mol per liter15 or 3.06 gpl. All our experiments have been done at concentrations lower than the critical micelle concentration. The glass vessels, glass drop holder and the rutile crystal were all cleaned with hot chromic acid followed by distilled water, concentrated hydrochloric acid, and again distilled water, and conductivity water. During the experiments, a nitrogen atmosphere was maintained. For this purpose, commercially purified nitrogen was further purified by passing it over hot copper wire at 450°C, then through columns of acidic chromous chloride solution, concentrated alkali solution and distilled water. APPARATUS AND METHODS Hysteresis was produced by the "captive drop" or constant volume drop method as well as by the "expanding-contracting drop" or variable volume drop method. The image of the drop while it is expanding, contracting or moving is projected on a screen and photographed. The developed film is projected through an enlarger and the contact angles measured with a protractor.

Jan 1, 1964

By John Skelton, E. J. Harvey

Seepage runs (stream flow measurements in a short time at many points in a basin,) and stream flow records are used to locate losing areas in stream basins in the Missouri Ozarks. The terrane consists of dolomitic limestone and sandstone of Ordovician and Cambrian age. Side-looking radar imagery emphasizes variations in topography and reveals two types of drainage basin topography, rough and smooth (deeply dissected and slightly dissected basins). In the deeply dissected basins (rough ones), main streams and tributaries generally gain. In the slightly dissected basins (smooth ones), the streams lose a part or all of their flow. Logan Creek, a tributary of Black River in the southeastern Ozarks, loses much of its storm runoff and all of its dry weather flow. East and West Forks of the Black River, north of Logan Creek, gain water through most of their main stems. On radar imagery Logan Creek basin has a light uniform tone and smooth texture in contrast to the darker tone and rough texture of the East and West Forks. The contrast is due to the difference in degree of dissection. Therefore, radar imagery may be useful in suggesting gaining or losing streams (or reaches of streams).

Jan 1, 1973

By V. L. Minear

This paper presents some of the problems encountered and solved by the construction industry during recent years while pressure grouting the foundation rock of dams. Pressure grouting has become "Standard Operational Procedure" and consequently many hundreds of thousands of bags of cement have been used for that purpose. There is nothing weird, mystical, or even particularly difficult about the basic idea. Holes are drilled in the rock and grout is pumped into them. This procedure is used to shut off the flow of water under the dam and to reduce the uplift on the dam. Like most other engineering and construction problems, the fundamental principle is simplicity itself, but some of the "minor details" are rather complex. When faced with the problem of actually forcing the grout into the rock, or keeping it there once it has been injected, an engineer frequently has need for all of the ingenuity and initiative that he has at his disposal. It is proposed to discuss these minor details at length, even at the risk of boring the reader. The difference between success and failure in a grouting program can well hinge upon some such detail that may not be fully understood. Pressure grouting is a method used to make good foundations from bad ones by plugging actual or potential passages within the rock through which water might escape and thereby diminish or even destroy the usefulness of the dam. In some special cases, pressure grouting has been used for the purpose of consolidating broken rock to increase its bearing power. Lacking this useful method, many of the dams constructed during recent years could not have been built. Most of the really excellent dam sites in this country have been utilized long ago. Consequently it becomes necessary to find methods of utilizing the less desirable sites. Pressure grouting plays a vital role in the methods developed. Engineers have learned the hard way, that the term "solid rock" is a misnomer. Solid rock does not exist to any considerable extent in nature. Practically all rock contains imperfections such as shrinkage cracks, bedding planes, joints, solution channels, folds, shear zones, crush zones, and the like. All these imperfections are weaknesses through which ground water is likely to flow. The function of rock grouting is to rectify these imperfections and make the rock as nearly "solid" as practicable. The location, direction, depth and number of grout holes to be drilled are important. Clearly, a hole must pierce fractures in order to serve a useful purpose, for grout cannot be forced into the rock itself. Were it possible to determine the pattern and extent of the cracks within the rock, it might be feasible to drill two or three strategically placed holes so as to make practicable the grouting of the whole integrated network of cracks from them. Such is not the case. While a study of the geology, surface indications, and drill cores is helpful in gaining an idea of subsurface conditions, in the final analysis, the seams must be located by trial and error methods. There can be no doubt that the closer the

Jan 1, 1949

By T. A. Rickard

In a previous paper (ante, p. 411) some description was given of the occurrence of the auriferous alluvium, extensive deposits of which lie among the highlands of the province of Otago, New Zealand. The present paper will describe some of the methods by which that alluvium is exploited. The alluvial mining of New Zealand is not yet hindered by " debris legislation." The mines are for the most part situated in a country of little agricultural value, and large rivers with rapid currents act as tailings conveyors. In time, however, steps will have to be taken to restrict the discharge into the Clutha of the tailings which are slowly raising the river-bottom. The methods of California have been followed in Otago with such alterations as peculiar local conditions require. The distinctive feature of the alluvial mining of Otago is the prominence given to the hydraulic elevator. The all-important factor in this form of mining is the control of an abundant water-supply at a suitable height above the level where it is to be utilized; and in this respect the gold-fields of the south island of New Zealand are most favora-

Jan 1, 1893

By F. W. Aul, R. C. Glenn

EXTRACTION techniques are of particular importance in determining size, shape an: crystal structure of particles smaller than l000Å in steels and other alloys. However, artifacts that can arise during the preparation of extraction replicas may lead to erroneous conclusions. The purpose of this note is to illustrate some of these artifacts and the misinformation that can result from their presence. An alloy of iron with 0.8 pct Cu was investigated in the following conditions: 1) Solution treated 3 days at 925°C in dry hydrogen and quenched in water. Aged in steps to precipitate copper, as follows: heated to 700°C, held 1 day; then furnace cooled to 50O°C, held 3 days; then furnace cooled to room temperature. 2) Solution treated 3 days at 925OC in dry hydrogen and furnace cooled to room temperature. 3) Solution treated 3 days at 925OC or 17 hr at 1100°C in dry hydrogen to dissolve all copper, then quenched in water. A normal parlodion dry-extraction technique was employed after etching the specimens with super picralP or with 2 pct nital. A wet-extraction method

Jan 1, 1962

By John F. Elliott, Martin Weinstein

The solubility of hydrogen in liquid Pure iron and in a number of liquid binary iron alloys has been measured in a Sieverts'-type apparatus. Sieverts' law is obeyed in all alloys studied UP to 1 atm Pressure H2. The alloying elements, Al, B, C, Co, Cu, Ge, P, S, and Sn, decrease the solubility while Cb, Cr, Mn, and Ni increase it. ALTHOUGH the importance of hydrogen in steel-making has long been recognized, there has been, until recently, very little information in the literature on the effect of alloying elements on the solubility of hydrogen in iron. There is also disagreement on the solubility of the gas in liquid pure iron. Because of the earlier work in this laboratory,1,2 with the Sieverts method to determine the solubility of nitrogen in liquid iron alloys, it was decided to apply the equipment and procedure to hydrogen. The literature that is pertinent to this study (Ftefs. 1 through 15) will be discussed later when the results of this investigation are considered rather than at this point to avoid repetition. The reaction under study is:

Jan 1, 1963

By G. V. Woody, J. D. Price

Many producers of by-product coke have spent considerable time and given considerable thought to the use of a substitute for low-volatile coal as an admixture with high-volatile coking coal for charging high-temperature by-product coke ovens. Generally speaking, there are two principal reasons for this, one being occasioned by the lack, in certain localities, of low-volatile coal delivered at a cost sufficiently low to permit its use, and another being the desirability of finding a substitute product with a delivered cost lower than the cost of the low-volatile coal. It was for the first of these reasons that the Colorado Fuel and Iron Corporation was particularly interested in this subject. This paper deals with the experimental work and the results obtained by that company in producing and using low-temperature char. Overcoming Defects in Coke from Colorado Coals Colorado coking coals are all of the high-volatile type and were all laid down during the Cretaceous period, which makes them something like 80 million or so years younger, geologically, than eastern coals. They behave, when coked alone, something like the Pittsburgh-seam coals. They make a very brittle, highly cross-fractured, fingery coke of fair shatter value but quite low in resistance to abrasion. Mixed with a low-volatile coking coal such as Poca- hontas or certain Oklahoma coals, they make a coke that is equal to virtually any of the eastern cokes. The inferior quality of Colorado coke has long been recognized, and a considerable amount of time, effort and money has been spent upon investigations of means for improving its physical properties. While it has been found that some improvement in quality of coke can be secured by the adjustment and control of such variables as pulverization, moisture content, oven temperature and bulk density of charge, and through the addition of certain inert materials such as pulverized coke breeze, pitch, high-volatile noncoking or semicoking coal, the benefits so gained have been comparatively small. There are no low or medium-volatile coking coals available within a reasonable freight-cost distance. Therefore a substitute for low-vol-atile coal was developed through low-tem-perature carbonization—or, more correctly speaking, through the partial devolatiliza-tion—of high-volatile coals. The blending of this lower volatile char with the high-volatile coking coal distinctly improves the quality of coke made from Colorado coal. There is nothing especially new about this idea. In 1908 a Japanese patent was taken out by Kotaro Shimomura, whose claim was: The method of making a nonfingery coke out of bituminous coals, without using natural coals of low-volatile matter; according to which a certain coal is heated at a temperature between about 300°C. and about 600°C. so as to leave about 15 to 25 per cent volatile matter in the coal; this coal is mixed with the

Jan 1, 1944

By J. D. Price, G. V. Woody

Many producers of by-product coke have spent considerable time and given considerable thought to the use of a substitute for low-volatile coal as an admixture with high-volatile coking coal for charging high-temperature by-product coke ovens. Generally speaking, there are two principal reasons for this, one being occasioned by the lack, in certain localities, of low-volatile coal delivered at a cost sufficiently low to permit its use, and another being the desirability of finding a substitute product with a delivered cost lower than the cost of the low-volatile coal. It was for the first of these reasons that the Colorado Fuel and Iron Corporation was particularly interested in this subject. This paper deals with the experimental work and the results obtained by that company in producing and using low-temperature char. Overcoming Defects in Coke from Colorado Coals Colorado coking coals are all of the high-volatile type and were all laid down during the Cretaceous period, which makes them something like 80 million or so years younger, geologically, than eastern coals. They behave, when coked alone, something like the Pittsburgh-seam coals. They make a very brittle, highly cross-fractured, fingery coke of fair shatter value but quite low in resistance to abrasion. Mixed with a low-volatile coking coal such as Poca- hontas or certain Oklahoma coals, they make a coke that is equal to virtually any of the eastern cokes. The inferior quality of Colorado coke has long been recognized, and a considerable amount of time, effort and money has been spent upon investigations of means for improving its physical properties. While it has been found that some improvement in quality of coke can be secured by the adjustment and control of such variables as pulverization, moisture content, oven temperature and bulk density of charge, and through the addition of certain inert materials such as pulverized coke breeze, pitch, high-volatile noncoking or semicoking coal, the benefits so gained have been comparatively small. There are no low or medium-volatile coking coals available within a reasonable freight-cost distance. Therefore a substitute for low-vol-atile coal was developed through low-tem-perature carbonization—or, more correctly speaking, through the partial devolatiliza-tion—of high-volatile coals. The blending of this lower volatile char with the high-volatile coking coal distinctly improves the quality of coke made from Colorado coal. There is nothing especially new about this idea. In 1908 a Japanese patent was taken out by Kotaro Shimomura, whose claim was: The method of making a nonfingery coke out of bituminous coals, without using natural coals of low-volatile matter; according to which a certain coal is heated at a temperature between about 300°C. and about 600°C. so as to leave about 15 to 25 per cent volatile matter in the coal; this coal is mixed with the

Jan 1, 1944

By J. S. Hromatko, L. J. Gurevich

In the course of the examination, at the BureLu of Standards, of fusible tin boiler plugs for the Steamboat Inspection Service, it became evident that an investigation should be undcrtaken to determine the precautions necessary in the manufacture of acceptable plugs. The results of the tests of these plugs show that their manufacture has improved, though at present not all of the plugs tested are, satisfactory. Table 1 gives the result of tests of some 1500 plugs from about 100 makers. Records of the tests show that several of the makers were able to produce satisfactory plugs with every pouring. The Steamboat Inspection Service has the following specifications for fusible plugs: "Fusible plugs for use in boilers of steam vessels under the jurisdiction of the Steamboat Inspection Service shall be made of bronze casing with the bore tapering continuously and openly from end to end, and filled from end to end with tin not less than 99.7 per cent. pure and to contain not more than 0.1 per cent. of lead and not more than 0.1 per cent. of zinc. The small end of the bore may be countersunk not more than 1/32 in. in depth and width, but no recess, thread, or cavity other than this countersink shall be allowed." Table 1.—Thirty-"five-mdh Testing Record of Fusible Plugs Causes of Rejection Inspection Period June-November, 1916.................. 311 32.8 47.2 3.8 11.5 15. 1 10.9 1 1.9 4.5 December, 1916-May, 1917............. 318 71.4 28.6 2.2 4.4 12.8 5.9 i ... 2.8 June-November, 1917.................. 228 73.0 27.01 ... 9.6, 5.2 9.6' ... 0.8 December, 1917-May. 1918............. 214 72.028.0 0.9 0.4 11.6 7.0 ... 7.9 June-November, 1918...............250 70.7 29.3 ... 2.0 20.0 5.2 ....2.8 December, 1918-April. 1919............ 23378.121.9 7.2 1.2 1 4.7 3.0 ... 6.0 Total 35 months....................1544.69.7 30.3 2.3 4.8 11 0 6.9 0.3 4.1

Jan 1, 1921

By Burt C. Mariacher

The Minerals Beneficiation Division meets each year at the Annual Meeting of AIME. All members are invited and encouraged to attend. For the information of those who did not attend the meeting in Denver last February, this column presents a summary of the reports given and topics discussed. Technical Committee Coordination Consolidation of technical programs having common interest to MBD and the Extractive Metallurgy Division is proving a considerable success, both on the technical committee level-through the efforts of the MBD-EMD Coordinating Committee-and in special symposia. MBD Chairman, R. S. Shoemaker, noted that J. D. Prater will be serving as Chairman of both the MBD Chemical Processing Committee and the EMD Hydrometallurgy Committee for 1970-71. R. P. Ehrlich commented on the cooperative effort of both divisions in organizing the Copper Metallurgy Symposium held at the Denver Meeting. This effort, he said, was important to the success of the Symposium. H. R. Spedden discussed inter-Division coordination activities on the SME level. The forthcoming MBD-M&E-EMD Joint Lead-Zinc Symposium is yet another example of progress in this direction.

Jan 1, 1970

By E. H. Sellards

ON Oct. 9, 1929, a sink formed in the Sour Lake salt dome oil field in Texas, and on Oct. 12 a second smaller sink formed at the north margin of the first. The purpose of this paper is to give such observations as it has been possible to make on the earth movement incident to this subsidence. Sour Lake salt dome is typical of the salt domes of the Gulf Coastal Plain of Texas. Structurally the dome is a plug of salt which rises to within 900 ft. or less of the surface. Above the salt is a cap rock consisting of anhydrite with more or less calcium carbonate. The salt plug, as contoured on the cap rock, is circular in outline with, however, some appreciable irregularities. Overlying the cap rock are relatively uncompacted sediments consisting of sand, clay and gumbo.. At the crest of the dome these deposits are no more than 700 or 800 ft. thick. However, the sides of the dome are steep, and the sediments thicken rapidly away from the crest. The sink formed about 1500 ft. northeast of the crest of the dome where the sediments overlying the cap rock are from 1000 to 1200 ft. thick. The cavity permitting the subsidence was quite certainly either in the cap rock or in the salt below the cap rock, so that the sink was formed by the caving of as much as 1000 or 1200 ft. of earth.

Jan 1, 1930