Search Documents

By H. S. Martin

Although it was known some years ago at the Utah Copper Co. mills that fine grinding improved flotation recoveries, no accurate data were available until recently as to just how far the grinding could be carried economically. In 1923 the ultimate degree of fineness for flotation feed was supposed to be about 10 per cent. on 65 mesh, with approximately 55 per cent. through 200 mesh, which meant that most of the mineral would pass 100 mesh. At this time Garfield and Wilfley tables were used ahead of flotation and a good deal of the coarse mineral removed prior to the ball mill regrind. Shortly afterwards, mill-scale tests developed the fact that on a feed containing not over 10 per cent. +65-mesh material flotation alone would give a copper recovery equal to that obtained by the combination of tables and flotation, but that on much coarser feed the recovery with flotation alone was lowered. This was at a time when all the sulfide minerals were floated if possible, so that the only requisite was to grind fine enough to free the mineral from gangue. Earliest Use of Microscopic Examination of Tailings As early as 1921, the writer had attempted to determine by chemical analysis the relative proportions of copper minerals in tailings from an ore that made extremely poor flotation results. Chemical analysis was not satisfactory or conclusive, and samples of these tailings were sent to the U. S. Bureau of Mines Station at the University of Utah for microscopic examination. The question at that time was to determine, if possible, which copper minerals had been lost and why, but R. E. Head, in his report, revealed other interesting data. He said in part: Briefly stated, the mineral partieles or grains may be classified into scparate groups as follows: 1. Free grains of pyrite, chalcopyrite, chalcocite and bornite, respectively, which contain 110 other included sulfides; 2. Grains in which all three of the copper sulfides are representel (the core may be of chalcopyrite, partially altered to boruite, these two minerals being cntirely surrounded by a shell of chalcocite); 3. Grains composed of equal amounts of bornite and chalcocite or chalcopyrite and chalcocite. The grains of free mineral particles are perhaps the most numerous, taking the ore as a whole, but it is noticeable that of the grains of combined or associated sulfides

Jan 1, 1930

By J. M. McDowell

A study has been made to deter~r~irre how the behavior of a water drivee reservoir changes as a function of the permeability of the formation and as a function of the size of the aquifer. The effect of pressure maintenance programs on the rote of nat11rn1 water influx is also studied, (IS well as the influence on the influx of the position of water injection we1ls with reference to the oil-water contact. The results are determined by the use of an electrical reservoir analyzer and are plotted as families of curves of pressure, natural water influx, and water injection vs time or cumulalive production. Two size aquifers are studided. One is limited with a 36-inile radius, and the, other approximates an infinite reservoir. The field remains the same in all respects for the completed. study except that the permeability is changed to agree with that assumed for the aquifer. 1 N TR ODUCTI ON this study was undertaken in -dcr to determine how the pres- sure decline and water influx of a water drive field would change as a function of the rate of fluid withdrawals, as a function of the permeability of the formation, and as a function of the size of the aquifer. The effect of pressure maintenance programs on the rate of natural water influx was also studied as was the position of water injection wells with reference to the oil-water contact. The information has been determined by the use of an electrical reservoir analyzer1, sometimes referred to as a Carter type analyzer. This instrument is an analog type computer which can be set up to represent a water-drive oil field. It can reproduce the past performance of the field in terms of analogous electrical quantities when the proper circuit analog of resistors and condensers has been determined, also, it can determine the future behavior for any method of production which may be selected, or permit the comparison among several different methods. Although most applications of the reservoir analyzer"" have been to thc study of specific field performance, it is intended to use the analyzer here to help understand how various reservoir characteristics effect the final performance of the field and to sec under what conditions water injection will be of benefit and to what extent. Within the oil industry the performance of water-drive reservoirs was first described analytically by LV. Hurst' and M. Muskat2 for certain types of boundary conditions. The solutions of the equations developed involved products of exponential functions and Bessel functions. Later publications by Hurst4 and van Ever-clingen" and the hooks of Muskat6 gave further information on reservoirs with other boundary conditions. They also presented rather extensive curves and tables to help evaluate the analytical expressions involved. A rccent series of publications by Chatas. bascd on the work of Hurst and van Everdingen, gives quite complete charts and tables of data to evaluate the pressure decline or water influx in infinite or limited radial reservoirs. and in linear reservoirs. The curves in all of these publications are given in dimensionless form

Jan 1, 1956

By Henry E. Colton

NeaR the town of Christiansburg, Va., occurs a singular feature in topographical as well as geological structure, which may be said to have an important bearing on a large area to the southwest. The great water-shed ridge, which divides the waters flowing into the St. Lawrence from those flowing into the Atlantic ocean, coming southwestward, forms all of what was the boundary of Maine as agreed upon by the treaty of 1783, and a part of the present boundary, all of the northern New Hampshire boundary, and entering Vermont, continues south of Lake George. Passing irregularly through New York, it enters Pennsylvania, and there bifurcating, sends one prong to the west as a divide between the waters of the lakes and the Ohio, while the other becomes the steady, regular ridge which gave it the name of Alleghany, and thus passes on southwestward through Virginia. At no point has it ever been the geological divide. Its course, commencing in the Archean rocks, has passed through nearly every series of formation, and comes into Virginia in the Carboniferous strata. The geological divide—the line between the fossiliferous and the non-fossiliferous rocks—lies, in Canada, to the west of it, but from New York south into Virginia is far to the east. Reference to Dr. Hitchcock'k map will show this. But at the locality noted these positions are changed; the water-divide becomes the eastern chain, and the geological divide is the western, returning, it may be said, to the positions occupied in the region where they originated. These relations are shown on the large map accompanying the present paper. For several miles, the track of the Norfolk and Western Railroad

Jan 1, 1888

By J. R. Cain

In every process for making steel there are one or more stages where the metal is exposed to gas of one kind or another. Thus, in the open-hearth furnace, the carbon dioxide and water vapor in the products of combustion are oxidizing toward the ferrous and manganous oxides in the slag, tending to convert these to higher oxides; the higher oxides then , oxidize the steel, so that indirectly the products of combustion are oxidizing toward the steel. In the Bessemer process, there is direct contact of air and steel; also, the water vapor in the air blown into the converter is continually decomposed by the molten steel, yielding hydrogen and ferrous oxide, both of which are in part taken up by the metal. In the electric-furnace processes, there is always more or less air in contact with the slag covering the metal, and this air and the gaseous reaction products from it are dissolved in the slag to some extent and thus transmitted in part to the steel. In the crucible processes, there is always entrapped air in the charges and the crucibles are more or less permeable to the gaseous products of combustion from the furnace. In all the processes of manufacture, the molten metal is exposed to air while tapping into ladles and ingot molds and has an opportunity to saturate itself with air or with gaseous or solid products generated by chemical reactions between air and steel. Sievertsl has shown that molten metals requirc but a few seconds to saturate themselves with a surrounding gas. No one familiar with the operations at a steel plant needs to be reminded of the important role that gases play at all stages. The familiar "boil" of open-hearth furnaces, due to evolution of carbon monoxide when iron ore is added to the molten steel; the spectacular operation of the Bessemer converter brought about entirely by a gaseous reagent; the almost magic effect of small quantities of silicon, manganese, or aluminum added to the molten metal in ladle or furnace in quickly preventing bubbling and evolution of gases; the unwelcome phenomena of blowholes in ingots that have not been properly manufactured—these

Jan 1, 1920

By AIME AIME

The Bulletin. The Bulletin of the Institute will be issued hereafter monthly instead of bi-monthly as heretofore. Among other reasons for this change, it is desired to effect thereby the earlier transmission to members of important papers, lists of candidates tin? membership, and other items of timely information. The New Haven Meeting. As already announced in special circular, the XCVIth meeting of the institute for the reading and discussion of papers will be held at New Haven, Conn., beginning Feb. 23, 1909. The Secretary of the Local Committee is Prof. J. D. Irving, Box D, Yale Station, New Haven. The program embraces visits to many interesting works in New Haven, Ansonia, Bridgeport, etc. The leading topics for discussion at the sessions will lie: The Conservation of Natural Resources; A Sea-Level Canal at Panama; and The Technical Education of Mining Engineers. But papers on other subjects also are announced. Lt is probable that a supplementary session of this meeting, will be held in New York City, at some time during March, 1909, as a joint session with other national engineering societies, for the farther discussion of the subject of The Conservation of Natural Resources. A Pacific Coast Meeting. It is now reasonably certain that the XCVIIth meeting will be held oil the Pacific Coast, including a. visit to the Exposition at Seattle, and various other points en. route going or coming, depending upon the route and program finally adopted. (lore definite information will be announced at the New Haven Meeting, or at the earliest possible date thereafter.

Jan 1, 1909

By B. R. Coil, C. A. Ross

NEW demands for underground power in the Miami mine of the Miami Copper Co., Miami, Ariz. has brought about expansion of the distribution system for both ac and dc power. Progress in mining equipment and the normal changes in the mine were responsible for this increased demand. Early power requirements were for pumping and haulage. A 440 v ac power line down No. 5 shaft took care of a small pumping load and shaft station lighting, 275 v dc power was generated by motor generator sets on the surface, with a churn drill hole from surface to the 570 haulage level serving as a cableway. Electric lights were installed where power was available, and thus were confined to the haulage level and shaft stations. All industrial power in the Miami area is 25-cycle, which dates back to the hydroelectric generator installation at Roosevelt Dam in 1908-10. The Problem The main haulage level was moved to the 720 level and later, to the 1000 level, requiring a longer feeder line with the resultant voltage drop. Also, as mining progressed to the east, the churn drill hole for the power cable would have been subjected to subsidence cracks. The first extension in the use of electricity was in electric blasting. About 1935 the mine went to electric blasting, using the dc haulage current. Bringing electric current to the working levels of the mine for blasting greatly expanded the use of electric lights. Lights were used in tool rooms, powder and cap magazines, stairways, and other semi-permanent installations. Like all mines, Miami Copper began to study and experiment with mechanical mucking and transportation of ore by slushers, shakers, and belts during the late 1930's and early 1940's. At the beginning of the program, power was supplied from the haulage level 275 v dc system. Later it became necessary to run a cable, carrying 440 v ac power, down the No. 7 ventilation shaft. The increased use of power came about gradually, and many new problems were added, not the least being the introduction of switch boards and power cables into the working areas of the mine, where drifts and crosscuts take weight, and require repairs. The 25-cycle current presented special problems, in that 25-cycle transformers are twice as large and about 2V2 times as heavy as 60-cycle transformers of the same power output. The 25-cycle transformers were considered too large for installation in the mining areas. In 1947 the distribution system was revised and standards were adopted, governed by the following

Jan 1, 1952

By R. A. Pallanch

IN his recent paper, "The Controversial Art of Flotation," (Mining Technology, March, 1944) E. H. Rose states that "flotation is a science in so many variables that only art can blend them." This statement is apt. It contains meat. In other words, a valid scientific reason is behind every flotative effect. Some of these reasons we understand, but much the greater number of them still escape us. This does not prevent us from "going places," as familiarity and experience with the problems result in an increasingly intelligent and artful handling of these effects. Hypotheses are built up by the individuals concerned to explain certain happenings. Many of these hypotheses have to be abandoned when placed under the glaring scrutiny of actual trial. A few survive the severest of tests, come through unscathed, and are elevated to the rank of theories, something susceptible of certain chemical and physical explanation, under the conditions of the particular plant concerned. If these theories continue to hold water under all the variations existing in most milling plants, they gradually become accepted as facts in the minds of the plant operators. But-and here is a big BUT-these so-called facts may fall down completely in another plant working under an entirely different set of conditions. In other words, each plant tends gradually to build up its own facts, which may or may not be facts at another operation.

Jan 1, 1945

By D. J. Carney, C. W. Boquist, E. C. Rudolphy

Effect of variations in sinter feed composition on sinter strength, bulk density, re-ducibility, chemical composition, and microstructure were determined by sintering experimental samples on a production sintering machine. Increasing amounts of roll scale, ore fines, return fines, and blast furnace slag were most beneficial to feed permeability, sinter bulk density, and strength. Burnt lime additions improved feed permeability but were not beneficial to sinter strength or bulk density. Sinter reducibility was adversely affected by all additives. DEVELOPMENT of methods for evaluating sinter quality, which would in some way predict the behavior of the sinter during charging and smelting in the blast furnace, has been given considerable attention in recent years. In a previous investigation at South Works of the United States Steel Corp., standard sinter sampling and testing procedures were developed.1,2 By modifying the sinter sampling device, a method of sintering experimental mix sinter samples upon a production Dwight-Lloyd sintering machine was also developed. This technique afforded a rapid and controlled method of investigating the effects of the various raw materials and additives on sinter quality and was used in this present investigation. Since the beginning of the present study in 1953, the results of numerous sinter investigations have been published, most of which were concerned with production tests of iron ore sinter, both here and abroad. Three groups of investigators reported results of experimental sinter studies that were related to this investigation. Voice et al.3 studied the effects of controlled variables on sinter quality by producing and testing experimental Northants iron ore sinter using an experimental sintering unit. Mor-rissey and Powers' determined the relationship between iron ore sinter quality and the moisture and coke content using a small laboratory sintering system. Burlingame et al.5 studied the effects of "additives" upon iron ore sinter using a laboratory sintering apparatus and laboratory grade raw materials. At South Works, it was considered desirable to study the effects of sinter mix composition and additives upon the quality of a flue dust-base sinter produced on a production sintering unit. Extrapolation of controlled laboratory test data to sintering plant operation lacking such precise control is not altogether satisfactory. Therefore, the present study was conducted in a manner which approximated production conditions as closely as possible. The raw materials used were those commonly encoun- tered in the production of flue dust and flue dust ore-type sinters and these were varied within extremes encountered in this type of sinter production. Experimental Procedure The experimental sinters were produced from 100 lb mixtures of sinter feed. The principal raw materials and additives used, their particle size, and approximate chemical composition are listed in Table I. The mixing of the raw materials was accomplished by means of a miniature single shaft pug mill shown in Fig, 1. The use of the pug mill as a mixer was decidea upon after encountering difficulty in reproducing the mixing and chopping effect of the sinter plant pug mill with other types of available small mixers. The miniature pug mill was constructed, consisting of 31/2x2x1/4 in, blades spaced 3 in. apart along a 3 ft shaft. Preliminary tests were run with this small mixer to establish the proper rotation speed and the required number of passes through the pug mill to thoroughly mix and distribute all the raw materials in a manner approximating the production Pug mill- Although the effects of varying the mosture content were determined in one particular series of tests, the amount of moisture added was changed as the composition of the experimental mix was varied. The aim in making water additions was to achieve a permeability as high as possible for each particular

Jan 1, 1956

By John D. Hanks

INTRODUCTION Chevron's Uranium Mill is located near Panna Maria, Texas; 70 miles southeast of San Antonio. Designed by Kaiser Engineering, the Mill will process a nominal 2500 dry T.P.D. of uranium bearing ore containing 15% uncombined moisture. Earl Torgerson, San Mateo, California, is the consulting metallurgist on process design. Feed to the plant consists of a mixture of high, medium and low grade sandy day ore; the average grade of the ore will be 0.7% throughout the life of the project. The ore is delivered to the mill via truck and stored by type in individual piles on a flat storage area. The ore is fed by conveyor to a semi-autogenous grinding mill. The SAG mill discharge slurry is pumped either to a storage tank or to the first of five mechanically agitated leach tanks where both H2SO and NaC103 are added. Following leaching, the slurry is mixed with thickener No. 2 overflow before being pumped to a six-thickener, countercurrent decantation circuit where the solution containing uranium is separated from the leach residue. The residue is washed essentially free of solubilized U308 values at the sixth thickener and discharged to an adjacent tailings pond. The first thickener overflow, containing approximately 0.4 grams U308 per liter, is filtered for clarification and sent to the liquid ion exchange (solvent extraction) section. The pregnant aqueous solution is mixed with organic solvent containing amine on which the complex uranyl sulfate ions are absorbed. The immiscible aqueous and organic solutions are mixed and separated in each of the four stages of solvent extraction. The final pregnant organic is directed to a stripping section. A strip solution containing (NH4)2S04 (ammonium sulfate) and NH4C1 (ammonium chloride) is contacted and separated from the organic in each of the four mixer-settler units. The strip solution is mixed with NH3 and the uranium precipitates along with trace amounts of sulfate, chloride, and ammonia. After washing in a thickener, the uranium precipitate or yellowcake is centrifuged and dried in a multiple hearth roaster. Overflow from the yellowcake thickener is recycled back to the stripping section of the solvent extraction circuit. The dried yellowcake concentrate contains more than 98% U308; diluents include H20, ammonia, chloride, etc.. Impurity concentratons in the product are sufficiently low, after drying, to permit direct shipment to refinement installations. ORE RECEIVING Ore from one or more mines will be stored on a pad adjacent to the uranium processing mill. Ore stored in the area may total 200,000 tons or more, which is equivalent to over a two month treatment reserve for the mill. In addition to providing surge capacity, the proposed storage facility permits natural oxidation of the ore and affords an area which, in turn, improve plant U308 recovery and reduces consumption of oxidizing reagents. The uranium bearing ore is segregated at the storage area into several distinct types. One group can be identified by its sandy, clay-like matrix and will be distinguished by its U308 concentration of high, medium, or low. Other ores contain substantial quantities of carbonaceous shale, typical of ore in the area. Feed is recovered from any one or combination of piles, in accordance with operating requirements and recovery factors. The run-of-mine ore, at 15% moisture, is transferred to a stationary, 24-inch by 24-inch grizzly. Undersize material falls into a 280-ton surge hopper located below grade, while oversize material is removed for preliminary size reduction. A sump-pump is located at the reclaim hopper to recover excess mositure and ore spillage for processing. Plant feed is continuously drawn from beneath the hopper at an average rate of 120 tons per hour by means of an apron feeder. The hopper is equipped with a low level safety system to protect the apron feeder assemble. The ore is transferred to a belt conveyor, elevated and discharged into a semi-autogeneous grinding (SAG) mill. Water addition at the discharge point is automatically controlled by a feed rate, moisture analyzer system located on the belt conveyor. GRINDING Minus 24-inch ore, at a rate of 120 mosit tons per hour and cyclone underflow at a rate of 137 moist tons per hour are combined with a controlled 186 gallons per minute fresh, warm plant process water. The mixture, at an average 68% solids, is fed to the SAG mill. The viscous mass is subjected to grinding at a temperature moderately above ambient resulting from use of the 140ºF well water. The 16.5'x5.0' Marcy Mill is driven by a 500 H.P. A.C. Motor. The mill will rotate at 73.4% of critical speed or 14.06 R.P.M. Eight percent of the mill's volume will be occupied by steel grinding balls; 22% by pulp. The mill is designed to rotate in either direction, in order to obtain maximum lifter and liner life. The SAG mill is equipped with a trommel having ½ -inch slots for removal of oversize material at its discharge and the large or oversize material is collected and either recirculated periodically or discarded. The undersize slurry is diluted to 64% solids with the addition of hot well water or mine water to the mill discharge sump. The flow is automatically controlled utilizing data from a gamma density meter. The slurry from the mill discharge sump is pumped to hydrocyclones to classify the particles. Underflow from the cyclones, at 80% + 28 mesh, is recycled to

Jan 1, 1979

By T. Egleston

The manufacture of charcoal in kilns was declared many years ago, after a series of experiments made in poorly constructed furnaces, to be unprofitable, and the subject is dismissed by most writers with the remark that in order to use the method economically the products of distillation, both liquid and gaseous, must be collected. It is asserted with truth that the number of kilns required for a large production of iron would be so great that it is doubtful whether any works would be justified in making the necessary outlay for their constructiou, but it can also be asserted with equal truth that for any such production in a given locality the use of charcoal as fuel would be eqnally unjustifiable. It appears to have been forgotten that there were other manufactures besides iron in which large amounts of charcoal were used, but these consumers seen] to have been guided entirely by the results of the experiments of the iron men, who necessarily made the largest qnantity of it. Some authors speak in a doubtful way of the quality of the charcoal produced, and a few concede that with great care good charcoal can he made in kilns, but that most of the workmen do not like kiln 'charcoal. This is the real secret of the opposition to this method of manufacture. Most of these objections were written when charcoal was the most important fuel used by the iron manufacturer, and when what was a largeproduction of iron for several furnaces was less than that produced by a single modern one, in localities where other fuels can be had. Almost all that has been written on the subject related to the use of the fuel for the manufacture of iron in the blast furnace, where very peculiar properties are required, and where the qnantity produced is limited by the height of the furnace, and this in turn by the crushing resistance of the charcoal. A large production was, therefore, only possible when the best and hardest woods were used. Of all these objections there is not a single one which is not eqnally applicable to any method of charcoal manufacture, whether it be meilers, pits, or furnaces. Until recently, therefore, the manufacturers of charcoal iron

Jan 1, 1880

By R. T. Southin

Cast ingots of 99.99 pct purity A1 and aluminum/copper alloys containing up to 2 pct Cu have been found to contain four zones rather than the three previously accepted, i.e., chill, colummar, and equiaxed zones. The fourth zone consists of a coarse dendritic layer across the top surface of the ingot which is open to the atmosphere. It is also found that the grains in the equiaxed region have a "cornet" shape, with a head which is coarsely dendritic and a tail which grew with the same structure as the columnar grains. Experiments using mechanical barriers, and others involving the elimination of the surface dendrile layer, have indicated that nucleation of the equiaxed zone is caused by the showering of dendritic particles from this surface dendrite layer. These particles are the dendritic heads found in the comet grains. A mechanism of nucleation and growth of these comet grains is put forward. Experiments with a number of other metals and alloys suggests that these conclusions may apply generally to ingots cast without the addition of nucleating agents, and solidified under normal conditions. THE macrostructure of cast ingots may contain the following three zones: i) a peripheral zone of fine equiaxed grains, commonly called the chill zone; ii) a zone of columnar grains extending inwards from the chill zone; iii) a central zone of equiaxed grains; these are normally larger than the chill grains. All three zones are not necessarily present in any particular ingot since their existence and magnitude depend upon the casting conditions and composition of the cast material. The mode of formation of zones i and ii is fairly well understood. However, the cause of the central equiaxed zone remains a matter of conjecture. Previous theories put forward to explain the mechanism of nucleation in the equiaxed zone have been examined by Chalmers1 and Winegard.2 At the time when the present work was carried out the most re -cent hypothesis was that due to Chalmers,1 who recognized more fully than previous workers that conditions in this zone during solidification were not conducive to nucleation. In his hypothesis, he suggested that nuclei were formed near the mould wall during the very early stages of solidification, and that they can drift into the central zone by convective motion. This was supported by evidence from experiments using mechanical barriers to stop the drift of nuclei. A similar hypothesis had previously been put forward by Genders.3 More recently, Jackson et al. 4 have observed that dendrite arms in organic compounds can melt off during solidification. They have postulated that this occurs in metals and alloys, and that the dendrite arms which have been freed from the main dendrite act as nuclei for the equiaxed zone. In the present work, critical metallographic examination has shown that there is a fourth zone in the macrostructure of cast ingots which is a dendritic layer over the top surface of the ingot. It is also shown that there is a relationship between this zone and nucleation of the equiaxed zone. EXPERIMENTAL DETAILS The alloys examined were prepared from super -purity aluminum of 99.99 pct min purity (spectro-graphically detected impurities of Cu, Fe, Si, and Mg) and copper of 99.98 pct min purity (spectrographically detected impurities of Si, Zn, As, Fe, Pb, Bi, Ni, Sn, Mn, Ag, Cr, and Al). Three compositions of ingots were examined, containing 0.0, 0.1, and 2 pct Cu, respectively. The alloys were melted in an alumina-lined salamander crucible using a medium-frequency electric induction furnace; when the appropriate casting temperature was reached, the alloys were cast without degassing or fluxing treatment. The mould used was made of electrode graphite and had the following dimensions: external diameter 6 in., height 9 in., with a mould cavity 8 in. deep and a diameter tapering from 5 in. at the top to 4 in. at the bottom. Casting temperatures used were generally in the order of 70" to 90°C above the liquidus and the mould was at room temperature before casting. Inserts kere placed in the mould cavity in some experiments. These consisted of either an 18-g stainless-steel tube of 2 in. diam held axially in the mould i in. off the bottom and extending 1 in. out of the top of the mould or a "trap-door" barrier of stainless-steel gauze of 24-mesh held horizontally in the mould 31/2 in. down from the top. The construction of this insert is shown in Fig. 1. All inserts were preheated prior to casting to prevent chilling. RESULTS The macrostructures of ingots of the three compositions are described, in terms of the three generally recognized zones, in Table I, and illustrated in Figs. 2(a) to (c). The most interesting observation in this table is that relating to the shape of the equiaxed grains, which were not in fact equiaxed but of almost tear-drop shape. Closer examination of these grains showed that each consisted of a head which had a coarse dendritic structure and a tail which always grew in the opposite direction to heat flow, and which had the same structure as that of the columnar material of the ingot concerned; i.e., in the pure aluminum and 0.1 pct Cu alloy it was cellular and in the 2 pct Cu alloy it was cellular-dendritic. Identification of original cast grains was greatly hampered in the super-purity aluminum ingots, and to a lesser degree in the 0.1 pct Cu alloy,

Jan 1, 1968

By Robert Bosworth

THE liability for damages to the surface caused by subsidence is an ever present threat in all underground mining. In ordinary lode mining, this threat rarely materializes into an action, due to the method of mining metalliferous ores, the dip of the veins, and the nature of the ground itself. In the mining of coal, however, this threat is very real. The coal frequently lies close to the surface, in beds underlying large areas of land of which the surface is suitable for: agricultural or urban development. Furthermore, the coal is generally mined by the "room and pillar" method and when the pillars of coal are removed, the subjacent support is destroyed. This question of the duty of surface support has now become a very live one in Colorado. What was waste prairie land a few years ago has become valuable agricultural land dotted here and there with growing towns. Frequent references will' be made here to Colorado conditions and adjudicated cases, but those conditions and cases and the conclusions to be drawn therefrom are applicable to all coal-mining states. Briefly stated, the question is "Does the owner of the substrata or underlying mineral owe any duty of surface support to the owner of the superjacent strata or surface?" There is no absolute duty of support owed by the mineral owner and this assertion is made with full knowledge of numerous expressions to the contrary by courts of Pennsylvania, Illinois, Colorado and other coal-mining states. Whether or not any duty exists depends upon the circumstances surrounding each case, and since in the nature of things those circumstances are rarely identical, there can be no absolute rule.

Jan 1, 1928

By T. S. West

Completion and production data presented for three wells in the Oakville area of Live Oak County, Texas, which were completed near the gas-oil or water-oil contact, indicate that coning may not be as prevalent a cause of failure in such cases as is commonly assumed. Failure in the cases discussed is indicated to be due instead to: (I) erosion of the formation, (2) flowing out of mud filter cake, or (3) failure of the cement. An open-hole gravel-pack type of completion procedure is proposed for preventing failures of this kind by preventing movement of all solid material in the space in which completion is made. Various combinations of layers of gravel, sand, and cement are utilized for this purpose. Experimental results and theoretical discussion as to the applicability of gravel pack completion are included. Introduction This paper is primarily a study of the reasons for failure of oil-well completions near the gas-oil or oil-water contact, and suggests a procedure for increasing the efficiency of this type of completion. The value of improvement in completion effectiveness near the gas or water zone is not confined, however, to wells of relatively thin oil columns. Thick oil columns become thin as depletion progresses. It would seem to follow that the minimum distance from the gas or water zone at which completion can be made in a new well indicates the limit to which depletion may be carried in a well having an oil column of any initial magnitude. Only four ways can be postulated in which high gas-oil or water-oil ratio can initially occur if the zone exposed for production is within the oil column: 1. Failure of the cementing material. 2. Vertical coning. 3. Failure along the boundary between the cement and the wall of the well. 4. Failure of the formation comprising the wall of the well. Cementing materials such as portland cement and plastics have reached a high stage of development. Failures of this type are probably due almost always to extraneous causes such as mud contamination rather than to faulty cementing material. Vertical coning can and obviously does occur. However, the usual occurrence of thin impermeable streaks in sand sections and the success with which open-hole drill-stem tests can be made near the gas-oil contact suggest that over-all effective vertical permeability, and in turn vertical coning, is less prevalent than frequently is assumed. Much has been written on failure by flowing out of the mud filter cake between cementing material and the formation. A filter cake is always present if, prior to cementing, mud has come in contact with a permeable formation at pressures exceeding the pressure head of the fluid it contains. Mechanical methods are in use for removing filter cake during the cementing operation? which undoubtedly are of

Jan 1, 1947

By T. S. West

Completion and production data presented for three wells in the Oakville area of Live Oak County, Texas, which were completed near the gas-oil or water-oil contact, indicate that coning may not be as prevalent a cause of failure in such cases as is commonly assumed. Failure in the cases discussed is indicated to be due instead to: (I) erosion of the formation, (2) flowing out of mud filter cake, or (3) failure of the cement. An open-hole gravel-pack type of completion procedure is proposed for preventing failures of this kind by preventing movement of all solid material in the space in which completion is made. Various combinations of layers of gravel, sand, and cement are utilized for this purpose. Experimental results and theoretical discussion as to the applicability of gravel pack completion are included. Introduction This paper is primarily a study of the reasons for failure of oil-well completions near the gas-oil or oil-water contact, and suggests a procedure for increasing the efficiency of this type of completion. The value of improvement in completion effectiveness near the gas or water zone is not confined, however, to wells of relatively thin oil columns. Thick oil columns become thin as depletion progresses. It would seem to follow that the minimum distance from the gas or water zone at which completion can be made in a new well indicates the limit to which depletion may be carried in a well having an oil column of any initial magnitude. Only four ways can be postulated in which high gas-oil or water-oil ratio can initially occur if the zone exposed for production is within the oil column: 1. Failure of the cementing material. 2. Vertical coning. 3. Failure along the boundary between the cement and the wall of the well. 4. Failure of the formation comprising the wall of the well. Cementing materials such as portland cement and plastics have reached a high stage of development. Failures of this type are probably due almost always to extraneous causes such as mud contamination rather than to faulty cementing material. Vertical coning can and obviously does occur. However, the usual occurrence of thin impermeable streaks in sand sections and the success with which open-hole drill-stem tests can be made near the gas-oil contact suggest that over-all effective vertical permeability, and in turn vertical coning, is less prevalent than frequently is assumed. Much has been written on failure by flowing out of the mud filter cake between cementing material and the formation. A filter cake is always present if, prior to cementing, mud has come in contact with a permeable formation at pressures exceeding the pressure head of the fluid it contains. Mechanical methods are in use for removing filter cake during the cementing operation? which undoubtedly are of

Jan 1, 1947

By C. H. P. Lupis, Henri Gaye

There are m -I conditions for the stability of a solution of m components with respect to infinitesinzal flucturations. However, in most cases, only one of these conditions has to be considered to determine the domain of instability and the existence of this more restrictive condition greatly simplifies the calculations. It may be used advantageously for the prediction of miscibility gaps and the method is illustrated in details for the case of the Ag-Pb-Zn system. THE thermodynamic conditions for the formation of a miscibility gap may be viewed as a necessary consequence of the conditions for spinodal decomposition. A previous article1 has examined in detail the form of these conditions for multicomponent systems. There is only one condition for the stability of a binary system (with respect to infinitesimal fluctuations), but there are two conditions for a ternary system, and m — 1 conditions for an m-component system. The probability of violating a stability condition, and thus forming a miscibility gap, obviously increases with the number of components, a result which is rather intuitive since the atoms of the solution have now many more ways of redistributing themselves and introducing complexities in the form of the free energy hy-persurface. It is of interest to take advantage of this possibility of precipitating new phases and to examine which stability condition is the likeliest to be violated, that is, which stability condition is thermodynamically the most restrictive. The finding of such a condition would greatly simplify the application of the stability criteria since only one condition could then be considered, instead of m - 1. In Ref. 1, coherency strain energy terms were neglected, thus restricting the applications of the treatment to solutions where they are negligible, such as liquid alloys. In the following study the same assumption will be made. To generalize the treatment to systems where the strain energy terms are sizable, the reader is referred to Cahn's classical article on spinodal decomposition.2 Let us designate by Gij the second derivative of the Gibbs free energy with respect to the number of moles ni and n j. There are several equivalent sets of m — 1 stability conditions.' The one considered here expresses that the successive diagonal determinants of order 1, 2, ... m — 1, associated with the symmetric Gij matrix (for 2 5 i, j 5 m) are positive.' For a binary solution 1-2, the condition for stability is: O(u=G22^0 [1] For a ternary system 1-2-3, the condition [I.] is re- tained (the value of G22 will differ, of course, according to the concentration of 3) and another condition is introduced: £>(21 = G22G33 - Gl3 ^ 0 [2] In a composition diagram, these two conditions define two domains of instability. Starting at a point where the solution is stable (for instance at a point where the solution is very dilute) we gradually change the composition until the condition [I] or [2] is violated. As already noted in the literature, e.g., in the work of Prigogine and Defay,3 it is the boundary of the domain (2) which is first crossed. For if we assume that the boundary of the domain (1) is reached first, at this point G22 = 0 and the second condition is necessarily violated (D(2) = -& 5 0), in contradiction with our original assumption. An exhaustive study of the ternary regular solution case may be found in the work of Meijering.4 Moreover if the boundaries of the two domains have a common point, they also have a common tangent. For if the two lines were to cross each other as is illustrated in Fig. 1(a) any point M in the line QP would be such that £> = 0 and 0"' > 0 which, as shown above, are incompatible results. Thus, the two lines must be tangent at their common point Q as illustrated in the example of Fig. l(b). The reasoning of Fig. l(a) implies that the point Q is not a "singular" point for either boundary line. This singularity may be of two types. First, the lines meet without crossing each other and without being tangent. Second, the tangent at Q for D"' or 0"' is not single-valued. Other types of singularity are unlikely because of the usual analytical forms of D"' and 0"'. The exception to the common tangent requirement due to the first type of singularity was pointed out by John Morral;5 it occurs when the common point, Q' or (3" in Fig. l(b), is located at a boundary of the composition diagram, e.g., at the line X3 = 0. It may also be noted that at the common nonsingular point Q of D(1) and D(2), Fig. 1(b), G23 is necessarily equal to zero, whereas at a point such as Q' or Q", this conclusion is no longer valid because the product G22G33 is now indefinite (of the form 0. a). The exception to the common tangent requirement due to the second type of singularity occurs when two branches of the same boundary line intersect, for example when D(1)or D(2) decomposes into a product of functions, at a point which belongs to the boundary of the other condition. It is possible to show by a simple analytical calculation that, in this case, if Q is a singular point of D(1), then it is necessarily a singular point of D(2), and that the reciprocal is true except if G33 = 0 at Q. For the present article, however, more elaboration on these singularities appears to be unwarranted. To generalize the previous results to an m -component system, we use the mathematical theorem stating that if the diagonal determinant D(r) = 0, then

Jan 1, 1970

By G. Y. Chin, M. T. Dolan, W. L. Mammel

In the case of plastic deformation by slip, von Mises&apos; showed that an arbitrary shape change of a crystal generally requires the activation of five independent slip systems. The selection of the five active systems was worked out by Taylor ,&apos; who hypothesized that, among all combinations of equivalent slip systems which are capable of accommodating a given imposed strain, the active combination is that one for which the sum of the absolute values of the glide shears is a minimum. Taylor analyzed the case of {lll}( 110) slip for fcc metals and applied the analysis to crystals undergoing axisymmetric flow, which approximates the shape change of an embedded grain in a polycrystalline aggregate deformed in tension (or compression). For the twelve equivalent (111) (110) slip systems, there are 384 independent combinations of five slip systems that satisfy the imposed strain.&apos; Taylor laboriously calculated the value of M = ZjIyj /E for each combination (although some were missed) and obtained the minimum M, hence the active combination, for a number of axial orientations distributed throughout the stereographic triangle. (yj is shear from slip on the th system and e is the tensile strain). Detailed contours of constant minimum M were recently obtained by Hosford and Backofen using a simplified but equivalent Bishop and ill&apos; analysis. Due to the numerous combinations of slip systems involved in the calculations, however, the full potential of the powerful Taylor analysis has not been exploited. For this reason, we have recently utilized techniques of linear programming to obtain solutions of the Taylor analysis for axisymmetric flow, for slip on {110)(< 111), {112)(111), and {123)(111) systems as well as mixed slip composed of these three systems. These slip modes are of obvious importance in the deformation of bcc crystals. Some of the salient results are summarized below. 1) Stress-Strain Data for Polycrystal. The value of M averaged over all axial orientations is the ratio of the tensile flow strength of a randomly oriented aggregate to the critical resolved shear stress for slip. This value enters importantly in theoretical deductions of the polycrystalline stress-strain curve from single-crystal data.2&apos;3&apos;5 Table I lists the values of Ma,, for the several cases of slip, as obtained by the present computer work. 2) Texture Hardening. Since the value of M depends on the axial orientation, the (tensile) flow strength of a specimen may be increased through texture control.&apos; An example of the computer results is shown in Fig. 1, where contours of minimum M have been computer-plotted for the case of mixed slip on {110}(111), {112)(111),and {123}(11 1) systems. It may be seen that, under axisymmetric flow, wires of (111) and (110) axial orientations are 50 pct stronger than those oriented at (100) .

Jan 1, 1968

By J. K. Brooke, F. A. Renninger

During 1966, crushed stone production in the United States totaled just over 811 million tons valued at almost $1.2 billion. This represented in- creases of 4 % in tonnage and 5 % in value over that for 1965. Excluding the crushed stone used for agricultural and certain industrial purposes (cement, lime and flux), crushed stone mineral aggregate production totaled 616.3 million tons valued at almost $910 million, also up roughly 4% in tonnage and 5% in value over the 1965 figures. Limestone was by far the most widely used rock variety, followed by basalt, granite and sandstone in that order. Concrete aggregate and roadstone continued as the main uses for stone, accounting for 63% of all tonnage produced in 1966 and 60% of total stone value. Sand and gravel production in 1966 increased 3% over that for 1965. Total 1966 output was just in excess of 934 million tons valued at almost $985 million as compared with 908 million tons at $957 million for the previous year. Excluding the higher valued industrial sands, 903.2 million tons of sand and gravel valued at $891.6 million were used directly as mineral aggregates, representing a 2.9% increase in tonnage and a 2.4% increase in value over 1965.

Jan 2, 1968

By W. A. Riggs

In a single year the total transportation cost equals nearly 30 pct of the value of mineral commodities, the largest single cost from the deposit to consumer. The magnitude of this economic factor calls for more complete understanding of cost and operational problems between producer and carrier than now exists. Details are given of the costs of providing transportation as well as freight rates for selling transportation. In 1958, transportation of mineral commodities in the United States required 600 billion ton-miles to move 1 3/4 billion tons of products of mines comprising solid fuels, crude oil, industrial minerals and rocks, and ores. Possibly 17 pct was handled by more than one mode of transport, since combinations of several modes of transport may, at times, achieve better service/cost results than any single mode. Total transportation cost of nearly $5 billion equaled roughly 30 pct of the value of the mineral commodities, the largest single cost from the mineral deposit to the consumer. The tremendous magnitude of this transportation undertaking demands much more complete understanding than now exists between mineral producers and carriers about the economic and operational problems of each other. A substantial portion of the daily work of the writer is spent in trying to act as a combination interpreter and catalyst between potential shippers and carriers, hoping to direct both to points of mutual understanding and advantage. For the purpose of this paper, it is necessary to ask mining people to accept some terminology and to try to appreciate the mental approach of the freight rate making people of the carriers. This paper will consider costs of providing transportation as well as freight rates for selling transportation—although these are fields of limited certainty. There are no accurate statistical breakdowns for all modes of transport and types of carriers indicating commodities, volume of traffic, distances, costs, and rates. Much information is available for railroads, and some for the regulated portions of air, motor, pipeline, and water transportation. Unregulated carriers, handling about half of the transportation of products of mines, are not required to report, and very little is known of their activities. Figures used herein are national in scope, unless otherwise indicated, and have generally been derived from Interstate Commerce Commission reports and files. Tonnage figures have been reduced to net tons of 2000 lb. The very generalized comparison of average mileage freight rate levels for various modes of transport provided by Fig. 1 affords advantageous perspective for the entire field of transportation costs. Dashed guide lines show cents per ton-mile, and dotted guide lines show percentage of first class railroad freight rate. While costs of other than railroad transportation more nearly follow constant cents per ton-mile functions, costs of railroad transportation show characteristic taper, or decrease in cents per-ton mile with increasing length of haul. This fundamental difference in cost is due largely to the fact that railroads and pipelines provide their own fully taxed roadway facilities while highway, waterway, and air carriers use government-provided tax-free roadway at no cost other than fuel, license, and certain excise taxes. Thus railroad and pipeline transportation might be said to carry heavy threshold costs in addition to those transportation costs which are directly variable with ton miles of transportation produced. The original basis of railroad freight rate structures lies in the classification of all articles of commerce into railroad class ralings ranging from 7 to 40 pct of first class (100 pct) rate level, dependent on value, hazard, loading characteristics, service requirements, and whether carload or less than carload. Classification tables and mileage-based (but arbitrarily grouped), rate scales are published as tariffs subject to approval by regulatory bodies. Used together, these determine class rates in cents per 100 lb between points in the U. S. Where local commercial or operating conditions render it advantageous for carriers to depart from

Jan 1, 1961

By T. F. Mueller, P. A. Witherspoon

For the case of an infinite radial system operating at constant terminal rate, the reservoir engineer often uses the "point source" solution of the diffiusivity equation to study pressure interference effects. At early times and at short distances from the inner boundary these solutions are invalid. The amount of error is often not precisely defined because of mathematical difficulties. Work presented here shows that, if dimensionless time is defined appropriately, previous solutions of the pressure equation can be displayed .as a family of curves on one chart. These solutions include the point source solution (referred to in the field of hydrology as the Theis solution) and other solutions obtained with digital computer methods. With these curves, an exact evaluation of the pressure drop within a reservoir or an aquifer can be made by the engineer. Examples of field problem solutions are presented. In most reservoirs the error involved when the Theis solution is employed is often negligible; whereas, in the calculation of interference effects in an aquifer, a substantial error can occur through such an approach. INTRODUCTION Flow equations are used in petroleum engineering to study the behavior of individual wells and reservoirs. In the case of wells, the pressure response at the wellbore face is the major point of interest; whereas, in the case of reservoirs, the pressure response at the interface of the aquifer boundary is sought. To aid in such studies, the flow equations have been solved in terms of the behavior at these two inner boundaries. Only limited work has been published in regard to the pressure conditions away from these points, i.e., within the reservoir or aquifer. Theis and Mortada are among the few who have reported on this problem. The Theis approach employs the exponential integral and is valid for pressure conditions that occur some distance away from the flow disturbance. It is derived from the concept of a point source, as opposed to a flow across some finite area. The Mortada results, on the other hand, are valid at all points within the reservoir or aquifer. They are presented in terms of dimension less ratios of the radius where the pressure is desired to the radius where the flow rate is measured. Their main use, in the past, has been in aquifer studies. The published results are presented in the form of graphs that are limited to a maximum radius ratio of 64. These graphical results are cumbersome to interpolate at non-integral radius ratios, so that one may be forced to utilize a rather involved analytical expression presented by Mortada. BASIC EQUATIONS The solutions of Mortada and Theis are both based on the diffusivity equation as applied to the case of an infinite radial system subject to a constant terminal rate. The equation is obtained by combining the material balance equation with Darcy&apos;s flow equation. The assumptions implicit in the use of this equation are as follows: (1) a single fluid is present that occupies the entire pore volume; (2) the reservoir is horizontal, homogeneous, uniform in thickness, and of infinite radial extent; (3) compressibility and viscosity of the fluid remain constant at all pressures; and (4) fluid density obeys the equation Using the diffusivity equation in situations where the above conditions do not hold will result in errors. These errors (not discussed here) but only the errors which arise in the solution of the equation itself. The diffusivity equation for the homogeneous reservoir conditions cited above can be written in cylindrical coordinates, as To obtain a dimensionless equation, so a single solution can be used for applications of different porosity, permeability and fluid properties, the following transformations are usually made: After these transformations are made, Eq. 3 .can be written in dimensionless form, as MORTADA SOLUTION One solution of Eq. 6 has been given by Mortada.

Jan 1, 1966

By G. A. Vissac

The only fine coal washer with proved automatic controls, the feldspar jig is capable of good efficiencies even at low separating gravities, handles a variety of products, and treats 150 tph and over. IN continental Europe the feldspar jig is used almost exclusively for cleaning the fine sizes of coal; it operates with an artificial bed, made up generally of pieces of feldspar or of any other hard and heavy rock with good cleavages. A primitive form of this machine requiring close supervision was used in this country years ago, but output was small. The modern machines are generally air-pulsated Baum-type jigs, with capacities up to 150 tph, and treat sizes from % in. to 0, usually previously dedusted or deslimed. These jigs are equipped with very accurate and sensitive automatic controls insuring satisfactory operation even at low separating gravity and with feeds irregular in quality and quantity. This paper will deal more particularly with coal cleaning separation, but the technical studies apply equally to all minerals. Theory of the Feldspar Jig To understand fully the operation of the feldspar jig and to appreciate its potential value, it is necessary to measure and analyze the motion of small particles of various specific gravities, falling in various media, under various conditions. As no practical formulas were available for that purpose, the writer has developed new theories and established new sets of formulas, which cannot be demonstrated here. They are applicable to all minerals and to many problems of coal or mineral concentration. These formulas do not pretend to absolute accuracy, but results, tested by comparison with experimentally recorded data, are sufficient for practical purposes, as they give definite indications of trends, relative values, and order of magnitude of the many factors involved. For pulsating motions no earlier formulas are available. In the case of continuous currents or motions, such formulas as Rittinger&apos;s, Allen&apos;s, or Stokes&apos;, over a hundred years old, apply only to special shapes and sizes of particles, involve factors and coefficients difficult to measure or appreciate, and deal only with free motions. They are of little use in solving practical problems. Units used with the formulas presented here are in the CGS system. Lateral friction and suction have been taken into account according- to methods currently used in aerodynamics, and only hindered motion is dealt with. As the feldspar jig is primarily intended to create a fluid bed condition, the mixture of fluids and solids obtained is homogeneous, and the apparent specific gravity of the separating medium is calculated accordingly. For instance, if 20 pct of the volume is coal and shale, with an average of 1.60 sp gr, in a liquid of 1.10 sp gr, the actual specific gravity of the separating fluid is 0.80 x 1.1 + 0.20 X 1.6 = 1.20. The fundamental equations are as follows: The general motion of a particle falling in a medium of specific gravity equal to u, hindered motion. is dv/dt = g/Ls [ L (s-u) - u/g v2 [1] g = 981 cm per sec, acceleration of gravity, and L = thickness of the particle of specific gravity (s) and velocity (v). The initial acceleration dv/dt = g (1-u/s ) [2] is a function of the specific gravity of the particle, only for a given medium, and independent of its dimensions—an ideal separating condition. The terminal velocity Vt = gxL- (s-u)/u, [3] for a given value of u, is a function of s and L. Two particles, L, s, and L2 s2, are said to be equivalent if they have the same terminal velocity, and accordingly L1/L2=s2-u/s1-u. [4] Two such particles cannot be separated by continuous currents, in any concentrating device. Because the initial accelerated motion, which provides for efficient separation, is followed by a constant velocity, which has a limiting effect, it is essen-

Jan 1, 1956