Search Documents

By Arthur Green

A GROUP of 13 cities situated in Los Angeles and Orange counties in Southern California is engaged in constructing an aqueduct to carry water from the Colorado River at a point near Parker, Arizona, to a distribution point sear Riverside, California. The aqueduct will have a total length of approximately 241 miles, and is designed to deliver 1605 cu. ft. of water per second, or a little more than one billion gallons per day. The aqueduct crosses a barren, desert waste and the project includes approximately 91 miles of 16-ft. tunnel. The large amount of tunnel driving that has been done in this country in the past few years has resulted in some remarkable developments in equipment and methods. The building of the Colorado River Aqueduct, with its 91 miles of tunnels, has called on the best engineering knowledge in the country. New and better equipment has been designed for all phases of the work, and this equipment has been coordinated and adapted to the various conditions with a high degree of efficiency. The result has been that records for tunnel driving have been set under adverse natural conditions that exceed the estimates for progress under good conditions. All of the tunnels in the main aqueduct, except the Valverde and Bernasconi at the western end, have a finished diameter, inside the concrete lining, of 16 ft. Fig. 4 shows a section of the tunnel with the concrete lining in place. Fig. 5 illustrates the finished tunnel in three typical sections. The standard tunnel grade is 3.432 ft. per mile in the 16-ft. tunnels, but the Valverde and Bernasconi tunnels have a steeper grade and a finished diameter of 15 ft. 3 in. The rough bore of the large main aqueduct tunnels averages 12.95 solid cubic yards of material per foot of advance in timbered sections and 10.76 solid cubic yards per foot in unsupported sections.

Jan 1, 1936

By P. S. Rudman

Crystal-structure occurrences in binary phase diagrams of fifth- and sixth-period elements, zirconium through palladium and hafniun through platinum, are surveyed with the conclusion that average .group number GN is the dominant correlative. This is interpreted in terms of curves of enthalpy differences between competitiue structures that are continuous func -tions of GN. It is further reasoned that the absolute formation energies may also be continuous functions of GN and if so can be simply obtained from the regatives of the heats of sublimation of the elements. It is shown that from such a heat of formation-GN plot the heats of mixing of alloy systems can be quantitatively predicted. For example, for sixth-period alloys very large exothermic heats of mixing are predicted for systems that span GN = 6 (i.e., Hf-Pt, Ta-Os, ...). Thermodynamic data with which to test these predictions do not appear to be available. If in the latter transition (A subgroup) elements we eliminate from consideration the fourth period where magnetic terms contribute to crystal-structure stability, as shown in Table I, there is a very regular sequence of structures. Using the group number (GN) assignments of Table I, which differ from the usual assignments of 8 to the elements listed as 8 through 10, it is perhaps trivial to say that the phase occurrence is a unique function of GN. However, the interesting aspect of alloys from among these elements is that the alloy structures also appear to correlate with GN. The GN for an alloy is given as GN = SixiGNi, where xi and GNi = atomic fraction and GN of component i, respectively. It is difficult to credit anyone in particular with having discovered this correlation, so many people have implicitly or explicitly employed it in the last 10 years. However, Bloom and Grant' in their correlation of s-phase occurrence with total number of d + s electrons were certainly one of the first to appreciate the correlation and Hume -Rothery2 appears to be responsible for the use of average GN as defined above. Only in the last few years have the phase diagrams of enough alloy systems been determined for this correlation to be surveyed with any degree of completeness. We shall here, in an abbreviated format, summarize the available phase-diagram literature and discuss some consequences of the GN correlation. BINARY DIAGRAM SURVEY In Figs. 1 to 3 the phase occurrences are summarized. In Fig. 4 the occurrence limits for the more common structures are summarized. That the GN of an alloy falls within the occurrence limits of a particular structure is a necessary but not a sufficient condition for the appearance of that structure. The preceding figures certainly illustrate that GN is a dominant correlative for structures of these elements. Many of the diagrams have complications, with ordering and other phase changes occurring in intermediate phases, that cannot be clearly accommodated in such a schematic survey and have hence been left out. Such omissions cannot, however, negate the GN correlations discussed here. Relative atomic size is also an important crystal-structure determinant and since atomic size varies quite regularly with GN for these elements it is possible that the apparent GN correlation is basically a size correlation. In Fig. 5 relative size occurrence limits are given for intermediate phases and extended terminal solutions. The relative volume, ?v/(v) - 2(vA - vB)/(vA + uB), has been taken as the measure

Jan 1, 1968

By A. J. Bartlett

Island Creek conditions are generally referred to as ideal; yet, as at all other properties, there are all known hazards of coal mining. The hardest of these hazards to combat is the human element. The basic thought in the minds of the management of these properties is to produce coal with the utmost safety, and it has impressed upon its supervisory force that it does not want a ton of coal unless it can be produced safely. This company has instituted a mine inspection department, which reports direct to the general manager, arid all matters pertaining to safety come under the direction of this department. Through the medium of the inspection department, the management is kept in touch with the actual conditions existing in general at all mines. Inspections are made regularly arid continuously; that is, at all times while the mine!: are in operation some sections of some mines are being examined. These inspections cover all active and inactive workings. Miners are contacted in their working places and other employees at their respective, work. A thorough check is made to see that the state mining laws are complied with and that company safety rules arc being observed. Night shifts receive the same attention as day shifts. All violations and dangerous practices are brought to the attention of the plant supervisory force with suggestions and recommendations; major hazards of emergency nature are taken up immediately with the management. Periodical inspections are also made of all tipples, preparation plants, dumping and hoisting equipment, to see that all machinery is properly guarded, and walkways and platforms properly fenced; conditions of equipmcnt and mechanical defects are also reported. Reports of inspection are written in letter form and in such a manner as to give the management a picture of the existing conditions at the time of inspection. Copies of inspection reports are forwarded to the superintendents with the general manager'? comments. It has been said, "There is nothing under God's heaven that justifies. your creation or your citizenship but this gospel: ' That the next greatest

Jan 1, 1938

By A. J. Bartlett

Island Creek conditions are generally referred to as ideal; yet, as at all other properties, there are all known hazards of coal mining. The hardest of these hazards to combat is the human element. The basic thought in the minds of the management of these properties is to produce coal with the utmost safety, and it has impressed upon its supervisory force that it does not want a ton of coal unless it can be produced safely. This company has instituted a mine inspection department, which reports direct to the general manager, arid all matters pertaining to safety come under the direction of this department. Through the medium of the inspection department, the management is kept in touch with the actual conditions existing in general at all mines. Inspections are made regularly arid continuously; that is, at all times while the mine!: are in operation some sections of some mines are being examined. These inspections cover all active and inactive workings. Miners are contacted in their working places and other employees at their respective, work. A thorough check is made to see that the state mining laws are complied with and that company safety rules arc being observed. Night shifts receive the same attention as day shifts. All violations and dangerous practices are brought to the attention of the plant supervisory force with suggestions and recommendations; major hazards of emergency nature are taken up immediately with the management. Periodical inspections are also made of all tipples, preparation plants, dumping and hoisting equipment, to see that all machinery is properly guarded, and walkways and platforms properly fenced; conditions of equipmcnt and mechanical defects are also reported. Reports of inspection are written in letter form and in such a manner as to give the management a picture of the existing conditions at the time of inspection. Copies of inspection reports are forwarded to the superintendents with the general manager'? comments. It has been said, "There is nothing under God's heaven that justifies. your creation or your citizenship but this gospel: ' That the next greatest

Jan 1, 1938

By B. M. Larsen, L. S. Darken

SOME years ago we collated all laboratory data then available to us on the distribution at equilibrium of manganese and of sulphur between metal and simple slags, and used the results in setting up an equation, which proved to be in accord with determinations of the distribution ratio of manganese and of sulphur between liquid steel and open-hearth slag, over a wide range of operating conditions. We now present an outline of our calculations and inferences on these two closely related questions, which are of especial importance because of the advisability of conserving manganese wherever possible. In general, our results show that in the open-hearth furnace equilibrium between metal and slag, with respect to both manganese and sulphur, is substantially attained during the finishing period of the heat, or in about a half hour to an hour after any additions were made. This implies that the end result will be identical whether manganese is added as alloy or metal to the liquid steel or as oxide to the slag. The proportion of total manganese retained by the steel is favored: (I) by use of the minimum amount of lime, consistent with other operating limitations, required to give a lime-silica ratio of about 2.4, which usually corresponds to a minimum practical slag volume; (2) by a high concentration in the slag of MnO relative to FeO; (3) by high operating temperature. Absorption of sulphur by the slag from the liquid metal is favored: (I) by large slag volume; (2 by a high concentration of active (or "free") lime and of manganese oxide dis) solved in the slag; (3) by low concentration of silica, iron oxide, and phosphate dissolved in the slag. DISTRIBUTION OF MANGANESE BETWEEN SLAG AND METAL AT EQUILIBRIUM On the basis that the distribution of manganese between liquid steel and slag is controlled by the reaction [FeO + Mn = MnO + Fe [A]slag metal slag metal] the distribution at equilibrium, at a given temperature, is expressed by the equilibrium constant for this reaction, which is defined as [K" aMoO aFeI1 dFec) aMn] where a is the activity of the molecular species denoted by the subscript. The activity of each of the several components, although it is not known precisely, is approximately equal to the concentration of each component expressed as its mol fraction; that is, as the ratio of the number of mols of the given component to the total number of mols of all the molecular species present in the metal or slag, as the case may be. Moreover, since the activity, or concentration, of iron in the liquid metal is in fact substantially constant, the term [afe] may be combined with K" to give a new constant K'. Making these changes,

Jan 1, 1942

By James D. McClung, H. J. Gluskoter, M. R. Geer

INTRODUCTION The purpose of coal preparation is to improve the quality of coal to make it suitable for a specific purpose by (1 ) cleaning to remove inorganic impurities; (2) sizing-crushing or screening, or both; or (3) special treatment, such as dedusting. The properties and quantities of impurities in coal are of major importance in the design and operation of steam generating equipment. Al- though boilers are often designed and equipped to use a wide range of coals, no boiler will perform equally well with all types of coals. All coals have certain properties that place limitations on their most advantageous use. These limitations are especially stringent for many of the older installations. Because of a general lowering of quality of raw coal in recent years, the need for coal cleaning has significantly increased. Among the factors contributing to the need for increased coal preparation are (1) increased demand for quality brought on by market and environmental requirements; (2) increased extraneous dilution caused by mine, health, and safety laws; and (3) depletion of the higher-quality coal seams.

Jan 1, 1979

By Leo P. Tarasov

Magnetic torque studies of ferromagnetic single crystals have been carried out in a number of laboratories during the last decade&apos;s2 and some work has been reported on polycrystalline material showing preferred orientation. Goss3 used the method extensively in developing electrical sheet with desirable magnetic properties, but he used it as a control rather than as a means of studying the texture. Bozorth4 made a quantitative correlation of a torque curve he obtained from some cold-rolled iron with the texture as determined from X-rays, but did not extend his studies beyond the one specimen. Other studies, which have been reported from time to time2,5 have also been incomplete in the sense that no effort was made to study a whole series of samples, differing only in degree of cold reduction or in the annealing temperature, in order to ascertain the effect of such treatments on the texture as revealed by torque measurements. It is the purpose of this investigation to make such a study, mainly in order to see how useful the method can be made when used under favorable circumstances and to find what kind of a correlation can be expected between magnetic and X-ray studies of texture. Before proceeding further, it is desirable to say a little about single crystals, so as to make clear the concepts involved in magnetic torque measurements. Magnetic Torque Method It is fairly well known nowadays that single crystals of ferromagnetic substances have directions of easy magnetization and of hard magnetization. In Fig. 1 are reproduced typical magnetization curves for a single crystal of iron, which show that in a < 100 > direction saturation occurs at low fields compared to those required to saturate the same crystal in a <110> or a <111> direction. (The magnetization intensity I is defined by the equation B = H + 4pI.) At fields high enough to

Jan 1, 1939

By Leo P. Tarasov

Magnetic torque studies of ferromagnetic single crystals have been carried out in a number of laboratories during the last decade&apos;s2 and some work has been reported on polycrystalline material showing preferred orientation. Goss3 used the method extensively in developing electrical sheet with desirable magnetic properties, but he used it as a control rather than as a means of studying the texture. Bozorth4 made a quantitative correlation of a torque curve he obtained from some cold-rolled iron with the texture as determined from X-rays, but did not extend his studies beyond the one specimen. Other studies, which have been reported from time to time2,5 have also been incomplete in the sense that no effort was made to study a whole series of samples, differing only in degree of cold reduction or in the annealing temperature, in order to ascertain the effect of such treatments on the texture as revealed by torque measurements. It is the purpose of this investigation to make such a study, mainly in order to see how useful the method can be made when used under favorable circumstances and to find what kind of a correlation can be expected between magnetic and X-ray studies of texture. Before proceeding further, it is desirable to say a little about single crystals, so as to make clear the concepts involved in magnetic torque measurements. Magnetic Torque Method It is fairly well known nowadays that single crystals of ferromagnetic substances have directions of easy magnetization and of hard magnetization. In Fig. 1 are reproduced typical magnetization curves for a single crystal of iron, which show that in a < 100 > direction saturation occurs at low fields compared to those required to saturate the same crystal in a <110> or a <111> direction. (The magnetization intensity I is defined by the equation B = H + 4pI.) At fields high enough to

Jan 1, 1939

By Nicholas J. Grant, William H. Ferguson, Bill C. Giessen

Ta-lr alloys have been examined over the complete range of compositions using metallographic and X-ray techniques. The terminal solid-solubility limits, solidus temperatures, and intermediate phases were determined. There are four inter-mediate phases: o, tetragonal, analogous to a (Fe-Cr); 0,. orthorhombic; az, tetragonal; and a TaZr,, cubic, AuCu, structure. Of these, o and a, melt peritecticaLly, a, decomposes peritectoidally, and a TaIrs has a congruent melting point. Three peri-tectic and one eutectic reactions occur. 1 HE Ta-Ir phase diagram has not been treated in the literature. Intermetallic phases and terminal solid solubilities have been described and estimated.&apos;-4 The previous findings have been confirmed in this work. A complete diagram with additional phases and solidus curves is presented. EXPERIMENTAL METHODS Starting materials were tantalum powder of 99.8 pct purity, supplied by the National Research Corp., Cambridge, Mass., and iridium powder of 99.9 pct purity, supplied by the Bishop Co., Malvern, Pa. Both powders were -200 mesh. Table I lists the analyses as given by the suppliers. A standard procedure was employed in making the alloy buttons, which was described in detail in Refs. 5 and 6, and which included repeated arc-melting of powder compacts and determination of the composition by the weight-balance method. This is especially justifiable due to the similar vapor pressures of tantalum and iridium. In the critical parts of the diagram, a spacing of 1/2 at. pct was used, based on premelted master alloy material. The observed structures and X-ray spectra were consistent with the composition sequence of the alloys. Table II lists the final alloy atomic percentages with the calculated percent error of composition. Cross sections representative in grain size and composition were selected for the study, as described in Ref. 5. Based on prior experience, no contamination from the tungsten electrode was considered. Temperature measurements were obtained using a Leeds and Northrup optical pyrometer and have been described extensively in Refs. 5 and 6. All heat treatments were made in the high-vacuum tantalum tube furnace mentioned in Ref. 5. Samples annealed in tantalum containers cooled from 1800" to 1000"~ in 5 sec; those annealed in ceramic crucibles cooled over the same range in 15 to 30 sec. The thermal treatments are listed in Table 111. All specimens were homogenized at 1735°C for 24 hr. Tantalum-rich compositions were treated in tantalum buckets. Iridium-rich compositions were annealed in tantalum buckets below the eutectic temperature of 1950°C; up to 2200°C, tungsten-lined tantalum baskets were used; and above 2200°C thoria crucibles were used. It was found that refractory oxides (in early stages of the investigation alumina crucibles were used up to 1800°C and thoria crucibles were used to 2400"~) give off minute amounts of oxygen and thereby influence the microstructure considerably, or react directly with the alloys.

Jan 1, 1963

The Honor Roll includes the names of all members of the Institute Whom we know to have been on active military duty it the date of compilation, Mar. 5, 1919. Despite our efforts to have this list accurate and complete, some of our members who have been rendering military service are probably left off because of the fact that we have not been informed of their military connection. The list of men in military service has been compiled with great difficulty owing to the modesty of the members, who in their patriotism began their service but neglected to send us notice. In 1918, We published a separate Honor Roll of the Institute in which we included a list entitled "On active duty in other departments of the service" which contained the names of members who were rendering important emergency service to the Government other than in the Army. This list is entirely omitted this year because any list We might compile for this purpose would be entirely inadequate and must inevitably do injustice to a large number of our members who have been devoting great time and making many sacrifices for the benefit of the government along lines not within our ken. It is not too much to say that almost all our membership in this country has been, more or less directly, doing its uttermost for the successful prosecu¬tion of the war. The active work of many of these members we are Well aware of, as is also the rest of the civilized world. Faithful and wholehearted efforts on the part of many other members we have not been informed of, so that any list would be both incomplete and unsatisfactory.

Jan 1, 1923

I. PRESIDING OFFICERS. At all Business meetings of the Institute the President, or, in his absence, the Vice-President, or, in the absence of both of them, any other member of the Board of Directors to be chosen by the meeting, shall preside. At all other meetings of the Institute the President of the Council or, in his absence, one of the Vice-Presidents, if present, shall preside II. ORDER OF BUSINESS. At each Business meeting of the Institute the order of business shall be as follows 1. Reading of minutes of preceding meeting. 2 Report of the President. 3. Report of the Treasurer. 4. Report of the Secretary. 5. Election of Directors. 6. Election of Members of the Council. 7. Reports of Standing Committees. 8. Reports of Special Committees. 9. Special Orders 10. Miscellaneous business. This order of business may be changed by a vote of a majority of the Members and Associates present in person or by proxy. The usual parliamentary rules shall govern all meetings of the Institute except in cases otherwise provided by the Constitution or the By-Laws. At all sessions of the Institute other than business meetings, the order of proceedings and the time of adjournment, shall rest in the discretion of the presiding officer

Jan 1, 1923

I. PRESIDING OFFICERS. At all Business meetings of the Institute the President, or, in his absence, the Vice-President, or, in the absence of both of them, any other member of the Board of Directors to be chosen by the meeting, shall preside. At all other meetings of the Institute the President of the Council or, in his absence, one of the Vice-Presidents, if present, shall preside II. ORDER OF BUSINESS. At each Business meeting of the Institute the order of business shall be as follows 1. Reading of minutes of preceding meeting. 2 Report of the President. 3. Report of the Treasurer. 4. Report of the Secretary. 5. Election of Directors. 6. Election of Members of the Council. 7. Reports of Standing Committees. 8. Reports of Special Committees. 9. Special Orders 10. Miscellaneous business. This order of business may be changed by a vote of a majority of the Members and Associates present in person or by proxy. The usual parliamentary rules shall govern all meetings of the Institute except in cases otherwise provided by the Constitution or the By-Laws. At all sessions of the Institute other than business meetings, the order of proceedings and the time of adjournment, shall rest in the discretion of the presiding officer

Jan 1, 1923

NAME AND OBJECT. SEc. 1. This Institute is incorporated under the Membership Corporations law of the State of New York ; its corporate name is American Institute of Mining Engineers; and its objects are such as are stated in its Certificate of Incorporation. ARTICLE II. MEMBERS. SEC. 1. The membership of the Institute shall comprise four classes, namely 1. Members ; 2. Honorary Members ; 3. Associates ; 4. Junior Members. All members shall be equally entitled to the privileges of membership, except¬ing that Honorary Members, Junior Members, and Members and Associates whose residences shall be outside of the United States, Mexico, and Canada shall not be entitled to vote. Members and Associates residing within the United States of America, Mexico, and Canada, and not in arrears for dues, shall be entitled to vote in person at the meetings of the Institute, or, as hereinafter provided for, by letter ballot. SEC. 2. The following classes of persons shall be eligible for membership in the Institute, namely : as Members, all professional mining . engineers, geologists, metallurgists, or chemists, and all persons actively engaged in mining and metal¬lurgical engineering, geology, or chemistry ; as Associates, all persons desirous of being connected with the Institute who in the opinion of the Board of Directors are suitable.

Jan 1, 1923

I. PRESIDING OFFICERS. At all Business meetings of the Institute the President, or, in his absence, the Vice-President, or, in the absence of both of them, any other member of the Board of Directors to be chosen by the meeting, shall preside. At all other meetings of the Institute the President of the Council or, in his absence, one of the Vice-Presidents, if present, shall preside II. ORDER OF BUSINESS. At each Business meeting of the Institute the order of business shall be as follows 1. Reading of minutes of preceding meeting. 2 Report of the President. 3. Report of the Treasurer. 4. Report of the Secretary. 5. Election of Directors. 6. Election of Members of the Council. 7. Reports of Standing Committees. 8. Reports of Special Committees. 9. Special Orders 10. Miscellaneous business. This order of business may be changed by a vote of a majority of the Members and Associates present in person or by proxy. The usual parliamentary rules shall govern all meetings of the Institute except in cases otherwise provided by the Constitution or the By-Laws. At all sessions of the Institute other than business meetings, the order of proceedings and the time of adjournment, shall rest in the discretion of the presiding officer

Jan 1, 1917

I. PRESIDING OFFICERS. At all Business meetings of the Institute the President, or, in his absence, the Vice-President, or, in the absence of both of them, any other member of the Board of Directors to be chosen by the meeting, shall preside. At all other meetings of the Institute the President of the Council or, in his absence, one of the Vice-Presidents, if present, shall preside II. ORDER OF BUSINESS. At each Business meeting of the Institute the order of business shall be as follows 1. Reading of minutes of preceding meeting. 2 Report of the President. 3. Report of the Treasurer. 4. Report of the Secretary. 5. Election of Directors. 6. Reports of Standing Committees. 7. Reports of Special Committees. 8. Special Orders 9. Miscellaneous business. This order of business may be changed by a vote of a majority of the Members and Associates present in person or by proxy. The usual parliamentary rules shall govern all meetings of the Institute except in cases otherwise provided by the Constitution or the By-Laws. At all sessions of the Institute other than business meetings, the order of proceedings and the time of adjournment, shall rest in the discretion of the presiding officer

Jan 1, 1923

NAME AND OBJECT. SEC. 1. This Institute is incorporated under the Membership Corporations law of the State of New York ; its corporate name is American Institute of Mining Engineers; and its objects are such as are stated in its Certificate of Incorporation. ARTICLE II. MEMBERS. SEC. 1. The membership of the Institute shall comprise four classes, namely 1. Members ; 2. Honorary Members ; 3. Associates ; 4. Junior Members. All members shall be equally entitled to the privileges of membership, except¬ing that Honorary Members, Junior Members, and Members and Associates whose residences shall be outside of the United States, Mexico, and Canada shall not be entitled to vote. Members and Associates residing within the United States of America, Mexico, and Canada, and not in arrears for dues, shall be entitled to vote in person at the meetings of the Institute, or, as hereinafter provided for, by letter ballot. SEC. 2. The following classes of persons shall be eligible for membership in the Institute, namely : as Members, all professional mining . engineers, geologists, metallurgists, or chemists, and all persons actively engaged in mining and metallurgical engineering, geology, or chemistry ; as Associates, all persons desirous of being connected with the Institute who in the opinion of the Board of Directors are suitable.

Jan 1, 1923

By C. G. Dunn

WITH respect to theories of recrystallization in metals plastically deformed, it has been said that the present status of this subject is far from satisfactory.1 It may also be said that before any mechanism of recrystallization for metals and alloys can be set forth in a satisfactory manner, there must be made available considerable data on orientation changes that occur during the deformation and recrystallization processes. Although extensive data have been published on recrystallization in single crystals and in polycrystalline specimens, more results of a type that can be classified according to simple orientation changes would be desirable in this complex field. It might even be said that before classifications are made according to types of orientation changes, it may be possible to classify a considerable amount of data into certain kinds of orientation states if groups of common or nearly common orientation occur. Methods for computing the probability of occurrence for various types of groups have been published2 and it has been pointed out in particular that it should be possible to analyze orientation data for high-order twin relationships between old and new grains even when agreement is not at all exact. In this connection, work on recrystallization in silicon ferrite reported in a paper concerned with complex groups of annealing twins&apos; indicated that some data were consistent with primary nucleation occurring according to a second-order or a third-order twin transformation. However, further work in this latter direction was definitely needed. It is, therefore, the purpose of the present paper to report data and analyses for primary nucleation in silicon ferrite following small deformations that have been carried out at the Pittsfield Works&apos; Laboratory of the General Electric Co. Analyses have been made with the aid of standard groups of twins that are reported elsewhere .4 PREPARATION OF SPECIMENS AND EXPERIMENTAL PROCEDURE The material used in the present investigation was taken&apos; from the same heat of steel as that used in a prior report.3 The finished strip in both cases was made by the Allegheny-Ludlum Steel Corporation according to methods that produce a high degree of preferred crystal orientation. Samples with large grains had the following composition: 3.45 per cent Si, 0.003 C, 0.008 P, 0.020 S, 0.075 Mn, 0.031 Al and 0.072 Cu. Thickness of specimens was 0.012 inches. Plastic deformation was produced by cold-rolling the samples on a mill with

Jan 1, 1945

[59H1-Water Law and Its Significance to the Mining Industry by Wells A Hutchins 59H2-Relation of Land Subsidence to Groundwater Withdrawals in the Upper Gulf Coast Region, Texas by Leonard A Wood and A G Winslow 59F3-Hydraulic Mining of Gilsonite and Its Application to Coal Mining by J H Baker 59H4-Recovery of Phosphates by In Situ Fluid Mining by Sylvain J Pirson 59F5-Coal Cleaning Plant Design for Minimum Operating Labor by Wm M Bertholf and John D Price 59F6-Coke Combustibility A Neglected Characteristic by J D Price 59B7-Union Carbide&apos;s Uranium Operation at Maybell, Colorado by K W Lentz and F T Temple 59H8-A Rapid Method for Estimating Alumina in Feldspathic Sands by Hugh H Bein 59H9-Water Laws as Related to Dredging in Idaho by Robert A Lothrop, Richard B Porter, and Robert P Porter 58B19-Separation and Washing of Alumina Process Residue by Morton Handelman 59B11-Feed Preparation and Froth Modification for Fatty Acid Flotation by Carl C Martin and Burt C Mariacher 59B12-Design Requirements for Tailing Disposal in the Southwest by E Vern Given 59B13-Semi-Dome Shaped Buildings for Bulk Storage by Edward E Ives and William L Payne]

Jan 1, 1961

By R. K. Waring, E. C. Truesdale

The Research Division of The New Jersey Zinc Company (of Pa.) has conducted, over a period of years, numerous tests of the reducibility of various zinc ores and the reactivity of various kinds of coal, using a number of different experimental methods. Most of these tests have involved the reduction of mixtures of ore and coal. In such cases the following simultaneous reactions are believed to be mainly responsible for the production of zinc, as was shown by Bodenstein1 some years ago: ZnO+ CO = Zn + CO2 [1] C + CO2 = 2 CO [2] Each of these reactions is dependent upon the other for the supply of CO and CO2 , respectively, and the over-all rate of formation of zinc vapor will be determined by the slower of these two reactions. An analogous pair of reactions sometimes of importance is: ZnO + H2 = Zn + H2 O [31 C + H2O = CO + Ha [4] While it is possible to obtain an indication of the relative reducibility of various ores, or of a fine versus a coarse ore, by testing them with a given coal, and while coal reactivities may be measured in a corresponding manner, a more direct determination of relative reaction rates is possible by carrying out the desired reactions, such as I and 2, separately and under reproducible conditions. It is one purpose of this paper to present some of the results that have been obtained by the latter method. C. G. Maier2 discusses the relative rates of reactions I and 2 and concludes that while at relatively low temperatures reaction I is faster than reaction 2, this difference becomes less with increasing temperatures, although at smelting temperatures reaction I is still the faster. He also says (p. 48), "At temperatures . . . between IIOO° and I3oo°C., . . . the zinc oxide reduction reaction is intrinsically more rapid than its physical limitations; that is, it is limited by gas diffusion rates." In the course of numerous reactivity tests involving the separate use of reactions and I and 2, we have obtained data that show by direct experiment, we believe for the first time, the correctness of Maier&apos;s statements concerning these reactions. We also include data on the relative rate of reaction 3, involving reduction by hydrogen. Finally, some interesting results obtained by carrying out the reduction of a zinc ore-coal briquet in streaming atmospheres of nitrogen, carbon monoxide and hydrogen, respectively, are presented. *

Jan 1, 1943

By E. C. Truesdale, R. K. Waring

The Research Division of The New Jersey Zinc Company (of Pa.) has conducted, over a period of years, numerous tests of the reducibility of various zinc ores and the reactivity of various kinds of coal, using a number of different experimental methods. Most of these tests have involved the reduction of mixtures of ore and coal. In such cases the following simultaneous reactions are believed to be mainly responsible for the production of zinc, as was shown by Bodenstein1 some years ago: ZnO+ CO = Zn + CO2 [1] C + CO2 = 2 CO [2] Each of these reactions is dependent upon the other for the supply of CO and CO2 , respectively, and the over-all rate of formation of zinc vapor will be determined by the slower of these two reactions. An analogous pair of reactions sometimes of importance is: ZnO + H2 = Zn + H2 O [31 C + H2O = CO + Ha [4] While it is possible to obtain an indication of the relative reducibility of various ores, or of a fine versus a coarse ore, by testing them with a given coal, and while coal reactivities may be measured in a corresponding manner, a more direct determination of relative reaction rates is possible by carrying out the desired reactions, such as I and 2, separately and under reproducible conditions. It is one purpose of this paper to present some of the results that have been obtained by the latter method. C. G. Maier2 discusses the relative rates of reactions I and 2 and concludes that while at relatively low temperatures reaction I is faster than reaction 2, this difference becomes less with increasing temperatures, although at smelting temperatures reaction I is still the faster. He also says (p. 48), "At temperatures . . . between IIOO° and I3oo°C., . . . the zinc oxide reduction reaction is intrinsically more rapid than its physical limitations; that is, it is limited by gas diffusion rates." In the course of numerous reactivity tests involving the separate use of reactions and I and 2, we have obtained data that show by direct experiment, we believe for the first time, the correctness of Maier&apos;s statements concerning these reactions. We also include data on the relative rate of reaction 3, involving reduction by hydrogen. Finally, some interesting results obtained by carrying out the reduction of a zinc ore-coal briquet in streaming atmospheres of nitrogen, carbon monoxide and hydrogen, respectively, are presented. *

Jan 1, 1943