Search Documents

A. Blainey (Ministry of Supply, Atomic Energy Research Establishment. Hnrtoell. England)—With ref- erence to the published work of Hausner et al. on the powder metallurgy of zirconium, it will be of interest to summarize briefly the results of preliminary work we have carried out on this subject at A.E.R.E., Harwell. For the early experiments we used zirconium

Jan 1, 1953

By J. L. Walter

Tungsten ingots with and without small amounts of aluminum, silicon, and potassium were prepared by conventional powder-metallurgy techniques and hot-rolled to 0.001-in.-thick sheet. The ingots were rolled three different ways: I) initially cross-rolled, then straight-rolled; 2) straight-rolled, and 3) straig-ht-rolled, then cross-rolled. Total reductions were 99.8 pct. Samples of the sheet were annealed, in vacuo, at temperatures from 1200" to 2200°C. Substructures and textures were determined by transmission electron microscopy and X-ray diffraction. The doping agents were found to form particles of mullite (Al,Si,O,,) which, on rolling., appear to form strings of particles aligned parallel to the rolling direction. These strings of purticles are associated with an increase in the recrystal-lizution temperature from 1400°C for undoped sheet ThE addition of small amounts of aluminum, silicon, and potassium to tungsten has a profound effect on the grain structure of drawn and recrystallized wire.'" The grains generally do not occupy the entire cross section of the wire and have lengths many times the wire diameter. The grain boundaries are, in general, nearly parallel to the wire axis and have long ''fingers" projecting one into the other as may be seen in Fig. 1, a longitudinal section of recrystallized doped wire. When unsuitable additions or no additions are made or the wire is not sufficiently reduced during draw- to 2000°C for doped sheet. The particles also limit lateral grain growth while allowing growth parallel to the rolling direction. This results in the formation by primary re crystallization of large highly elongated grains of specific preferred orientation. The undoped sheet recrystallized to small equiaxed gains. The preferred orientations of the large grains were determined from axis density plots to be (113) (691). (0i3) (362), (116) (304) types for the initially cross-rolled then straight rolled material. These orientations are similar to the orientations of the large elongated grains in doped and heavily drawn tungsten wire. The nucleation of the large grains appears to occur by recovery of certain of the polygonized regions of specific orientation, followed by strain-induced boundary migration.

Jan 1, 1968

By J. Chipman, N. J. Grant, H. L. Bishop

Lime and dicalcium-silicate crucibles were equilibrated with molten iron and liquid slags containing iron oxide and small amounts of sulfur. The oxygen content of metal, iron oxide activities, and desulfurization values of the slags were determined in the temperature range 1530 to 1700°C. The influence of magnesia in the slag and the temperature dependence of the solubility of lime in liquid iron oxide and the ferric oxide content were established. The temperature contour of the liquidus surface of iron-silicate slags saturated with lime and dicalcium silicate was also established at 1600°C. THE importance of the role that slag composition plays in the refining of steel has been known for many years. Numerous studies have been made using actual plant data in order to establish the relationship between the composition of the slag and metal during the refining of a heat of liquid steel. These results rarely represent equilibrium conditions since completion of the various chemical reactions involved in steelmaking is seldom realized. In order to establish quantitatively the equilibrium conditions existing between the slag and metal, several laboratory studies have been conducted in the past 20 years to determine the reactions important in slag control. These investigations have included studies of simple liquid basic and acid slags as well as more complex slag systems which approach those commonly found during the refining of a heat of steel. Since most of the previous studies of simple basic iron-oxide slags equilibriated with molten iron were made in magnesia crucibles, it was not possible to establish the distribution of sulfur and oxygen between molten iron and slags consisting only of the three essential components, lime, silica, and iron oxide. This investigation was undertaken to establish the equilibrium conditions for simple lime-iron oxide and lime-silica-iron oxide slags. Accordingly, it was expedient to prepare crucibles both of lime and dicalcium silicate to establish the equilibrium conditions between molten iron and iron-oxide slags saturated with the refractory materials and free from other components. The only other studies of the equilibrium between molten iron and lime-saturated slags are those of Fischer and vom Ende, 1, 2 in which the solubility of oxygen was determined in an air atmosphere. The

Jan 1, 1959

By P. G. Meikle, C. T. Holland

The effect of the condition of friction upon the ultimate unit compressive strength as determined between the compressed faces of precisely machined coal specimens and specially prepared testing platens has been examined. Reductions of 30 to 40% in the ultimate unit compressive strength of these model coal pillars have been verified when lubricants areused between the faces as compared to non-lubricated faces. Increase in unit compressive strength due to confinement at each of three levels of friction appears to follow generally the widely accepted "1/2 power law", i.e. S - C (L/T)1/2 where S is the unit ultimate strength, C is a constant dependent on the coal being tested and the coefficient of friction acting at the compression surfaces and L and T are the least width and thickness of the specimen, respectively. Results suggest that the surface condition of both the specimen and platens should be mentioned in detail in conjunction with compression testing, for although the term (L/T)1/2 is adequate for all practical purposes, the coefficient C is directly dependent on the condition of interfacial friction, all else remaining constant. One phase of the investigation of the confining effect of friction on the ultimate unit compressive strength of small coal specimens has recently been completed at the School of Mines of West Virginia University. The efficient control of ground is of fundamental importance to successful mining operations and the design of support pillars has always presented the mining engineer with a difficult and intriguing engineering problem. Since about the turn of the century, many investigators have performed extensive laboratory tests on small coal specimens in efforts to solve some of the perplexing problems of strata control and pillar action in coal mines. A detailed review of this work would serve no purpose here, but a brief mention of the more significant contributions is in order. Muller16 was perhaps the first to illustrate the effect of confining pressure on the strength of coal specimens in compression. His work has recently been more carefully expanded by the experiments of Murrell17 in Great Britain. Rice and Enzian l9 observed that as the size of cubical test specimens increased, the unit compressive strength decreased. These observations were later supplemented by Lawall and Holland, 13 by Greenwald4,5 et a1 at the U. S. Bureau of Mines, by Gaddy3 as well as by Steart,22 Millard15 et a1 and Evans2 et al. Gaddy3 seems to have been first to quantify this relationship with his equation: S = K/vd , where S - ultimate unit compressive strength (psi), K = a constant dependent on the coal, and D =edge dimension (in inches). Holland7 concluded that the strength of coal as affected by lateral dimensions and thickness could be expressed as where K = a coefficient dependent upon the coal, L = least width of pillar (in.) and T = thickness of pillar (in.). Data supplied by this formula have been compared to the estimated stresses in pillars that had been standing for long periods in coal mines and in the cases so far studied the results indicate that the formula predictions are sufficiently accurate for engineering purposes (Holland11 ). This equation therefore is believed to be the simplest and most accurate tool available at the present time for approximating the strength of a coal pillar (over a specified range of L/T) in situ. However, Holland7,9 has indicated that friction between the coal pillars and the top and bottom rock

Jan 1, 1965

By R. F. Domagala, D. J. McPherson

Iodide zirconium was combined with calculated amounts of ZrO2 or master alloys and arc-melted. Annealing treatments were carried out at 21 temperature levels. Metallographic examination of the heat treated specimens permitted construction of the binary phase diagram from zirconium to ZrO2. Oxygen additions to zirconium raise the transformation temperature as well as the melting point. Features of the diagram include the peritectic formation of beta, the formation of alpha directly from the melt, an intermediate phase ZrOB with a' range of homogeneity, and a eutectic between alpha and Zr02. PHASE relationships in the Zr-0 system were determined in the range 0 to 66. 7 atomic pct 0 (ZrO,). Arc-melted alloys were annealed at temperature levels between 600" and 2000°C. Determination of the phase boundaries was accomplished by metallographic evaluation of specimens quenched from the various temperatures. Incipient melting techniques were used to determine solidus curves, and X-ray diffraction work was employed to study the lattice parameters of the a solid solution and the phase ZrO,. Experimental Procedures Westinghouse "Grade 1" iodide zirconium crystal bar (approximately 99.8 pct pure) was employed for the investigation. This material is substantially free of the impurity inclusions characteristic of most zirconium metal. Previous work has shown it to be the most satisfactory grade for phase diagram studies. The zirconium crystal bar, as-received, was coated with corrosion product from autoclave tests by which its grade designation is determined. The bars were sand blasted lightly, pickled for 1 min in a 20 pct HN0,-5 pct HF aqueous solution, rinsed in water and acetone, and dried. The bars were rolled to about 1/32 in. strip, cut into 10 in. lengths, and pickled again. The material was sheared to approximately Y4 in. squares, cleaned with acetone, and stored for use. Two pounds of specially prepared "chemically pure," and 100 grams of spectrographic grade ZrO, were obtained for the preparation of alloys. The "Specpure" ZrO, was obtained from Johnson, Mat-they Co.. Ltd.. and Titanium Alloy Manufacturing Div. of National Lead Co. supplied the other grade of oxide. The "chemically pure" material (henceforth referred to as C.P. ZrO,) was used for the preparation of all alloys employed in the determination of phase relationships. A limited number of alloys were prepared with the "Specpure" oxide to recheck certain phase boundaries. Analyses of the two grades of oxide are given in Table I. The C.P. ZrOI was received in powder form, not suitable for arc melting. Therefore, this material was compressed to wafers 1 in. in diameter and about Vn in. thick. These were segmented and stored for use. The "Specpure" material, in the form of small granules, was suitable for use in the as-received condition. A nonconsumable electrode arc-melting furnace was used to prepare alloys. A water-cooled copper crucible and tungsten-tipped electrode were employed. The material was placed in the crucible and rapidly melted under a protective atmosphere of helium gas by striking the arc on a tungsten stud and directing it upon the charge material. Details of operation, including drawings of this type furnace, have been published.'

Jan 1, 1955

By G. A. Beske, P. Hilsch, J. Wulff

The effects of the growth precipitates on the su-perconduching properties of an Al- 15 al. pel Zu alloy have been studied using magneization, transition lem-perature, and residual resistivity measurements. Aging at 230C for 1/2 to 11 he produces an increase in Hfp, Ike field of first penetration, and tut increase in trapped flux. The upper critical field, Hc2 remains constant for such aging tunes. Aging at 200°C produces a decrease in Hfp and an increase in trapped flux. The transition temperature remains constant at Tc - 1.227° ± 0.02°K for aging at 220°C for tims of from 1/2 to 10 hr, and for aging at 200°C it remains constant at Tc. = 1.18° i 0.02°K for times from 1/2 hv to 26 hr. The observed behavior indicates that the superconducting matrix when aged at 220°C behaves tike a type U su-perconducior, but when aged at 200°C behares like a type I superconductor. The magnetization changes after aging can be attributed to the growth and clutnge in distribution of the precipitate in a matrix of fixed composition. IT has been realized for some time that the superconducting properties of alloys are highly structure-sensitive. This is evident in the work of Mould and Mapother1 who examined the properties of an aluminum alloy. Precipitation effects have also been briefly mentioned in other studies.2-4 Bonnin and coworkers5 have observed a sharp inc rease in trapped flux in an A1-Mg alloy when the residual resistivity reaches a value that indicates it is a type II superconductor. Recently Blanc, Goodman, and Nemoz5p have reported on precipitation effects in A1-Ag alloys. Detailed studies of precipitation in Pb-Sn and Pb-Cd alloys made by Livingston6 serve to show that the upper critical fields are enhanced by quenched-in solute. Furthermore. at various stages in the precipitation process? the upper critical field is determined largely by the remanent solute. The observed magnetic hysteresis and trapped flux in such alloys result from the interaction between precipitate and the flux filaments in the mixed state. The flux trapping appears to depend largely on the precipitate distribution and is greater if the superconductor is type II than if it is type I. To examine the effect of precipitation in another alloy system, particularly one in which the composition of the superconducting phase does not change significantly during the course of precipitation, the Al-Zn system seems interesting, especially in view of the transition temperature and resistivity studies of Chiou and seraphim.' Furthermore, the recent detailed electron-microscope studies of an Al-Zn alloy by Richards and Garwood8 provide a guide for relating superconducting properties to changes in structure. For these reasons, magnetization, transition temperature, and residual resistivity measurements for varying times of heat treatment at two temperatures were made with a -15 at. pct Al-Zn alloy. The results are reported in this paper. I) EXPERIMENTAL The alloy used was prepared by Cominco Products Inc. from 99.9999 A1 and 99.999 Zn. It was chill-cast, swaged, and drawn to 0.125-in.-diam rod. The analyzed composition was 15.6 at. pct Zn (31.1 wt pct). A jeweler's saw was used to cut the 0.125-in.-diam rod into the 0.875-in. lengths needed for magnetization measurements. The ends of the cylinders were slightly beveled to remove the sharp edges. A portion of the original 0.125-in.-diam rod was drawn into 0.010-in.-diam wire and used for transition temperature measurements. Specimens were suspended from wires within a vertical furnace during heat treatment. All were homogenized at 500°C for a minimum of 3 days and subsequently solutionized for times in excess of 6 hr. The solutionizing temperature was held constant to +3°C. Individual specimens were homogenized, quenched, and aged several times and no effects indicating loss of zinc were noted. The suspended specimens were quenched by cutting the wires and allowing the specimens to fall into a silicone oil bath held at the aging temperature. They were then isothermally transforked by aging in the same bath used for quenching. After aging for the required time (approximately 10 min aging was necessary before the upper critical field reached a fixed value), they were briefly (1 to 2 sec) dipped into an acetone bath at room temperature to remove adherent oil and then immediately transferred to liquid nitrogen where they remained until inserted into the helium bath (usually within an hour). The temperature of the aging bath was held constant to +3°C for longer aging times. The cryostat used for the measurement of superconducting properties consisted of outer and inner dewars for liquid nitrogen and liquid helium, Stokes 6-in. booster diffusion pump and Stokes Model 212 mechanical pump, temperature controller to measure and control the temperature of the helium bath, and a superconducting solenoid with inserted search coils to provide the magnetic field and measure the magnetic moment of the specimens. A schematic diagram of the cryostat is shown in Fig. 1. An ultimate temperature of 0.85°K was reached with this apparatus. The temperature controller used is similar to the one described by Blake and chase.' A 0.5 pct Allen-Bradley carbon resistor and a nichronle heater (200

Jan 1, 1968

By Samuel Storchheim

IT was noted that variations existed in the magnetic properties, namely, coercive force, He, and rema-nence, Br, of 18/8 stainless steel wires of the same analysis when these wires were given the same percentage of reductiori of area at different rates of reduction. In order to determine the extent of these variations, a program was initiated whereby commercial 302 and 304 stainless steels were drawn with a wide variation of speeds. Ultimate tensile strengths and specific resistances, as well as the Hc-BT measurements, were determined. If variations of considerable magnitude were found, it was thought that the knowledge accrued from the investigation could probably aid in determining the particular drawing speed required to obtain desired properties for a given specification for a particular analysis of wire. Drawing Procedure Two specimens (set I, No. 302 and No. 304), the chemical analyses of which are given in Table I, were drawn at different speeds, namely, 45 to 3900 ft per min, directly from 0.016 in. diam wire to 0.004 in. diam wire, a 93.7 pct reduction of area. To obtain this high percentage of reduction, the wire at 0.016 in. was softened by annealing at 1150°C. It was then strung in a No. 16CF variable speed Vaughn drawing unit and passed through 13 B.&S. gage dies of successively smaller diameter, as shown in the accompanying table. Following this step, several hundred feet of the wire was drawn, at a particular speed, through the dies and wound upon a spool. Once the sample of wire was drawn at the desired speed, the spool with the finished sample was removed, tagged for later identification, and an empty spool was placed in the machine. Another wire sample was drawn at a different speed, after making the necessary adjustments upon the Vaughn unit. At the greater speeds, several thousand feet of sample were drawn to insure that the wire to be used for testing would be uniform. This was done because the desired speed was not reached instantly; the wire taking a short while to attain the required drawing rate. All speed measurements were made by placing a tachometer against one of the machine's pulleys during the actual drawing of the specimens. 84.4 pct reduction of area. The 0.072 in. diameter wire was also annealed at 1150°C. The process of obtaining samples was the same as described above. The only difference between the two was that the rates involved were not as extensive, set II covering a range of 625 to 1150 ft per min. Tensile tests were carried out for the 0.004 in. diam wires on a horizontal Scott Tensile Tester, while tensile tests for the 0.028 in. diam wires were made on a vertical Scott Tensile Tester. Each value listed in the tables represented the average of five samples with a maximum deviation of approximately 3 pct among the samples. Resistance per foot of the wires was determined by use of standard bridges accurate to the nearest hundreth of an ohm for the 0.004 in. wire, and to the nearest thousandth of an ohm for the 0.028 in. wire. The resistances per foot were then converted to resistivities by use of the following equation: P = RxCM where R is the resistance per ft in ohms per ft; CM, the area in circular mils; and P, the resistivity in ohms—CM. The values listed in the tables likewise

Jan 1, 1952

By E. C. W. Perryman

On electropolishing, high-purity Cu-Sn and Cu-Sn-P alloys with more than 5 to 9 pct Sn were found to contain many grain boundaries with a ridge-and-furrow profile. The effect was not eliminated by solution treatment and was present at the new boundaries in recrystallized material. It could be produced by diffusing tin into the 3 pct Sn alloy and it is concluded that the effect is due to enrichment of certain boundaries in tin, or possibly in an impurity present in the tin, in solid solution. IN the hot working of tin bronzes, especially those with moderately high tin contents, considerable difficulty is frequently encountered from intercrystal-line weakness, which results in cracking at the edges in sheet on strip rolling and in the unsupported regions of the rod in rod rolling.' These difficulties are not at all pronounced with up to 3 pct Sn, but at 5 pct Sn impose serious limitations and at higher tin contents, especially if the phosphorus content is also high, they may become very severe. In some work carried out at the laboratories of The British Non-Ferrous Metals Research Association it was found that a notable lack of ductility in tension at elevated temperatures, associated with intercrystal-line failure, was characteristic of tin bronzes even of relatively high purity. That the intercrystalline fracture is not due to a brittle or molten impurity phase at the grain boundaries was shown by the fact that the temperature at which intercrystalline fracture first occurred decreased with decrease of rate of straining. Tensile tests on some commercial tin bronzes, reported by Goetzel,² show a similar fall in ductility with increasing temperature. As no visual evidence had been obtained showing that the grain boundaries of the tin bronzes were different from those in copper, a more detailed microscopical examination was carried out, and the results of this are given in the present report. Several workers"' have observed that electrolytic polishing is a powerful tool for detecting small amounts of a second phase and in particular for detecting high solute concentrations, "equilibrium segregation," at grain boundaries. Since it had been found that the suggested solutions for electropolishing bronze and the standard solutions for brass and copper did not give satisfactory results it was first necessary to find a suitable electropolishing solution.' Experimental Procedure Materials Used: The cast and wrought materials used for this work were the same as those used for the mechanical tests referred to above. They comprised 3, 6, and 9 pct Sn alloys without phosphorus and the same three basic alloys with 0.03 and 0.4 pct P. A 5 pct Sn alloy without phosphorus, of similar purity, was also examined. The basis materials were Chempur tin, high purity 15 pct phosphor-copper and cathode copper, and spectrographic analyses are given in Table I. Treatment: The cathode copper was first melted under charcoal, degassed by plunging marble chips beneath the surface, and cast through a coal gas flame into sand molds to produce a number of small ingots which after machining were of a suitable size for subsequent vacuum melting. Chill cast bars of the alloys, approximately 1¼ in. in diameter, were then made by melting and casting in vacuo, the tern-

Jan 1, 1954

By Frederick Laist

THE object of the construction and operation of the 80-ton leaching plant was to test out the leaching of sand tailings on a large scale and, if possible, determine a definite method of operation, and the best construction for the larger unit which is now being built. It was also of importance to obtain some practical data as regards cost items. The 80-ton plant was not expected to be a commercial success. A leaching process on such low-grade material necessitates the treatment of a very large tonnage.. Such a cost item as labor, for instance, is entirely out of proportion in such a small plant. The amounts of acid, salt, scrap iron, and fuel for roasting, however, are the same per ton in an 80-ton plant as in a 2,000-ton plant. These costs were definitely established. Also the percentages of extraction and grade of tailings were definitely determined for a large-sized unit. Following will be found the description of the plant, the method of operation and the results obtained. A -general view of the plant is given in Fig. 1. The bins consisted of one coal bin with a capacity of 30 tons, one salt bin with a capacity of 20 tons, and a "mill tailings" or feed bin which held 70 tons. The coal and salt bins were placed with their floor level even with the firing floor of the roasting furnace. The feed bin, to give it greater capacity, discharged about 12 ft. below this point, to a 12-in. conveyor belt, which, in turn discharged into a pug mill. This fed another conveyor belt, which discharged into the top hearth of the furnace. The furnace was an ordinary six-hearth MacDougall roaster, .20-ft. in diameter. It was equipped with two fire boxes, on opposite sides, the flames entering on the third hearth. An induced draft was obtained with a Buffalo blower, worked as an exhaust fan. Just above the top hearth was an annular flue around the whole circumference of the furnace. Slots at intervals of about 18 in. led from this flue down into the top hearth. The slots were 2 in. wide by 6 in. long. This annular flue proved rather unsatisfactory, as it tended to fill up with flue dust and choke the slots, thus cutting down the draft. The volume of gas through

Jan 8, 1914

By Charles S. Barrett

The experiments reported in this paper have been fruitful in disclosing the mechanism of the deformation of iron in compression. They have established the nature of "deformation bands," "etch bands," or "X-bands," that have been a recognized but little understood feature in the structure of cold-worked metals since the early days of metallography, and have shown the role of the bands in the development of preferred orientations by cold-working. The work has also shown the relation of the orientation of individual grains to the preferred orientation of the aggregate. Some of the methods previously used in the determination of the indices of slip planes and slip directions are shown to be untrustworthy in the presence of deformation bands. The conclusion is reached that many slip planes and slip directions must operate during each stage in the compression of a single crystal, and that theories failing to take account of this require revision. In conducting the experiments a method of compression has been used by which extreme reductions can easily be reached, even to the limit set by the metal's capacity to deform without fracture. The work is a portion of a research program on the plastic properties of iron and steel. It is being used as a foundation for studies of orientntions resulting from recrystallization and is being extended to other metals and other types of deformation. Previous Work The previous experiments are few and have given confusing results Onol compressed a polycrystalline alpha-iron specimen between two flan plates of a testing machine and found that severe deformation oriented the crystals into a duplex preferred orientation, one set of crystallites having a cube diagonal of the body-centered cubic lattice parallel to the compression axis, and another set having a cube axis parallel to the compression axis. We shall speak of this structure as a double fiber texture of the type [111] + [100]. Wever2 also made an X-ray determination of the texture

Jan 1, 1939

By Charles S. Barrett

The experiments reported in this paper have been fruitful in disclosing the mechanism of the deformation of iron in compression. They have established the nature of "deformation bands," "etch bands," or "X-bands," that have been a recognized but little understood feature in the structure of cold-worked metals since the early days of metallography, and have shown the role of the bands in the development of preferred orientations by cold-working. The work has also shown the relation of the orientation of individual grains to the preferred orientation of the aggregate. Some of the methods previously used in the determination of the indices of slip planes and slip directions are shown to be untrustworthy in the presence of deformation bands. The conclusion is reached that many slip planes and slip directions must operate during each stage in the compression of a single crystal, and that theories failing to take account of this require revision. In conducting the experiments a method of compression has been used by which extreme reductions can easily be reached, even to the limit set by the metal's capacity to deform without fracture. The work is a portion of a research program on the plastic properties of iron and steel. It is being used as a foundation for studies of orientntions resulting from recrystallization and is being extended to other metals and other types of deformation. Previous Work The previous experiments are few and have given confusing results Onol compressed a polycrystalline alpha-iron specimen between two flan plates of a testing machine and found that severe deformation oriented the crystals into a duplex preferred orientation, one set of crystallites having a cube diagonal of the body-centered cubic lattice parallel to the compression axis, and another set having a cube axis parallel to the compression axis. We shall speak of this structure as a double fiber texture of the type [111] + [100]. Wever2 also made an X-ray determination of the texture

Jan 1, 1939

By C. H. Mathewson

(New York Meeting, February, 1916) DURING the past year considerable work dealing with the mechanical properties and microstructure following the anneal under uniform conditions of certain types of commercial rolled brass has been done in this laboratory. Since these experiments were conducted with the active cooperation of the Bridgeport Brass Co., involving free use of its product, and have thus furnished information which is characteristic of some of its special mixtures, full publication of the numerical relationships and comparative results encountered does not seem justifiable. Some of the more general features of this work are, however, available and it is our present purpose to use the material in question, along with some results of special tests, in discussing the characteristics of recrystallization as related to the degree of hardening by strain and the ordinary annealing variables. We desire to make acknowledgment of the many courtesies extended by Mr. Charles Ferry, Metallurgist of the Bridgeport Brass Co., and the value of his cooperation, which has greatly stimulated the study of brass in this laboratory. A clear and systematic presentation of the principal relations between temperature and time of anneal, the changing physical properties and microstructure and the degree of previous reduction by cold-rolling, was first made, in the case of rolled brass and copper, by the French engineer, C. Grard,1 in 1909, although much fragmentary information of this general character had appeared earlier and the main facts involved were undoubtedly known to many brass specialists through their own private research. From this work, it appears that in the cartridge mixture (67 per cent. copper, 33 per cent. zinc) the properties imparted by cold-working within the limits, 13 to 75 per cent. reduction of area by rolling

Jan 1, 1916

By J. Parker

As a practicing mining engineer, I face many rock mechanics' problems daily and would like to mention one or two examples to illustrate the current gap between laboratory investigations and actual field problems. I would like to endorse Dr. Obert's suggestion that more field measurements and observations should be undertaken. There is an ever-increasing body of data beginning with Hast's results in Sweden,l then measurements at Elliot Lake, Canada, and so on, including our own measurements at White Pine, which clearly indicate that the horizontal stresses underground. are often at least as large as the vertical stresses. Visual observation of the deformation of roof and pillars (including failure due to horizontal compres- sion) also demonstrates that the horizontal stresses are often most important: Yet almost every laboratory investigation begins with the assumption that the only stresses acting are vertical. Roof spans in layered formations. for example, are calculated on the assumption that the rock behaves as a gravity loaded beam. This is all too often unrealistic.

Jan 1, 1967

By Michael H. Kuryla, Galen H. Clevenger

Some years after Nobel made his epoch-making contribution to the knowledge of high explosives, Sprengell described a new class of detonating explosives consisting of mixtures, made immediately before use, of an oxidizing agent and a combustible substance.2 The novel feature of the Sprengel explosives is that the constituents alone are non-explosive during manufacture, storage and transport. Despite this advantage, and although some of these have been used in important work, they are now little used, possibly on account of the greater inconvenience to the user, compared with explosives supplied by the manufacturer in final form. Liquid-oxygen explosives are a type of Sprengel explosive in that the oxidizing agent (liquid oxygen) and the combustible substance or substances (solid carbonaceous matter alone or in combination with liquid hydrocarbons or even metallic powders and, at times inert absorbents) are brought together immediately before use. The components separately are non-explosive. The possibility of using liquid oxygen as one of the components of an explosive was perhaps first suggested by Sprengel, who stated that the beau ideal of a detonating explosive was a mixture of eight parts of liquid oxygen with one part of liquid hydrogen. Although the liquefaction of air3 had been accomplished in the laboratory as early

Jan 1, 1923

By Michael H. Kuryla, Galen H. Clevenger

Some years after Nobel made his epoch-making contribution to the knowledge of high explosives, Sprengell described a new class of detonating explosives consisting of mixtures, made immediately before use, of an oxidizing agent and a combustible substance.2 The novel feature of the Sprengel explosives is that the constituents alone are non-explosive during manufacture, storage and transport. Despite this advantage, and although some of these have been used in important work, they are now little used, possibly on account of the greater inconvenience to the user, compared with explosives supplied by the manufacturer in final form. Liquid-oxygen explosives are a type of Sprengel explosive in that the oxidizing agent (liquid oxygen) and the combustible substance or substances (solid carbonaceous matter alone or in combination with liquid hydrocarbons or even metallic powders and, at times inert absorbents) are brought together immediately before use. The components separately are non-explosive. The possibility of using liquid oxygen as one of the components of an explosive was perhaps first suggested by Sprengel, who stated that the beau ideal of a detonating explosive was a mixture of eight parts of liquid oxygen with one part of liquid hydrogen. Although the liquefaction of air3 had been accomplished in the laboratory as early

Jan 1, 1923

By Joseph Kuti

Longwall mining is the term used for the underground extraction of a wide and deep panel of coal. Such a panel may be blocked out by one or more entries on either side ("head" and "tail") of a longwall face. If all the entries are pre-driven, the panel extraction is termed longwall retreat mining. With one exception, all the longwall faces in the United States are of this type.1 Prior to the general decline in the rates of production with Continuous Miners, the development of the multiple entries generally kept ahead of the longwall extraction rate. This is no longer the case: longwall extraction rates far exceed the rate of development. In addition to this problem, in newly established mines, the development of a haulage and bleeder system based on multiple entries results in a lead-time of three years or more before longwall mining can be applied.

Jan 11, 1979

By E. Orowan

LONG before the role of dislocations in the plastic deformation of crystals was recognized, the stress-strain field around dislocations received considerable attention in the theory of elasticity. It seems that Weingarten1 was the first to consider dislocations as simple and typical sources of internal stress in elastic solids, and Volterra2 and Timpe3 investigated their elastic field. Fig 3-1 shows the two basic types of dislocations considered by Volterra. The first arises by making a straight-edged .plane cut in a solid, displacing the two surfaces of the cut in their own plane relatively to one another by a constant amount in a direction perpendicular to the edge, and welding them together; this is shown in Fig 3-la, where the outer cylindrical surface represents the boundary of the solid, and the thin spiral cylinder around the edge of the cut has been removed in order to avoid infinities of stress and strain. The second type of dislocation is shown in Fig 3-lb; here the surfaces of the cut have been displaced relatively to one another by a constant amount parallel to the edge, and then welded together. After J. M. Burgers,4 these two types are called edge and screw dislocations, respectively. They represent simple limiting cases; in the general case, the surfaces of the cut are displaced by a constant vector that lies in the plane of the surface but has components both parallel and perpendicular to the edge of the cut. This vector is the Burgers or slip vector. The name “dislocation” was given by A. E. H. Love;5 it was bor-

Jan 1, 1954

In March 1962, over three months ahead of schedule, production began from the Ventersdorp Contact Reef of the Western Deep Levels Ltd. mine on the West Witwatersrand. Few mines have captured the interest of mining men and the public as has Western Deep Levels. It has presented the gold mining industry with a challenge which involved the opening of an ultradeep mine with the attendant problems of exceptionally heavy capital commitments ($77 million to start of production), high rock temperatures and pressures at great depths, cementation and pumping in an area notorious for the volume of subsurface water, and the necessity for entirely new thinking and the application of new ideas. HISTORY Not all the problems facing Western Deep Levels were, however, new. Situated 43 miles from Johannesburg, just off the main road to Potchefstroom, Western Deep Levels was the sixth company to undertake mining operations on what is known as the West Wits line and it could draw on the wealth of experience gained by other pioneer mines in the area.

Jan 12, 1962

By Simon D. Strauss

What are future prospects for U.S. mining? In many quarters the assumption is made that this country has passed its zenith as a mineral producer -- that it is in a period of decline and that it is becoming a have-not nation like Japan and much of Western Europe. These industrial rivals of ours must depend almost entirely on others for their mineral supplies. In trying to answer this question one must of course distinguish between resources and productive capacity. In today's volatile and competitive markets, the definition of what are reserves and what are merely identified resources becomes ever more difficult. Many large deposits have been found that are unlikely to be viable in the marketplace under normal conditions but that can be of significance to the nation's military and industrial security in times of emergency. I should like to draw on personal experience from World War I1 for illustration. 4fter Pearl Harbor great concern developed over the availability of a long 1ist of strategic materials for which this country was largely dependent on imports. Included were a number of minerals of which domestic deposits had been identified. Among these were chromite, manganese ore, mercury, mica and tungsten.

Jan 1, 1982

By George H. K. Schenck

The greatest difficulty in choosing solutions to environmental problems ill a free market economy (such as ours) stems from two factors: adverse effects of pollution are largely external to the producer, and expenditures made that improve the environment result in benefits that are free to all, These two factors are sufficient to explain why the solution to many environmental problems is to be found in public action. Such action is most likely to be economic- ally efficient if it can be carried out so that industry retains the freedom to make decisions based on the free market. Two examples-a zoned discharge fee and innovation of recycling systems-illustrate the type of changes in the mineral industry that would lead to an improved environment. The first requires that ownership of the relevant public resources be vested in control agencies. The second indicates that profit opportunities existing in solid waste recycling should facilitate innovation. Both concepts can reduce environmental loadings but will require imaginative thought from persons in the mineral industries.

Jan 1, 1971