Search Documents

By Herbert H. Uhlig

Although the mechanical properties of high-carbon manganese-iron alloys, particularly the Hadfield manganese steels, have been established, the literature discloses discrepancies in the reported properties for the low-carbon alloys. Hadfieldla summarized the existing data up to 1927, including the investigations of Guillet, Arnold, Strauss, Burgess and Aston, and reported his own values for alloys containing for the most part from 0.06 to 0.I5 per cent carbon. He noted: From these comparisons it wil! be seen that while there is a broad and general agreement as to the character of the alloys at the different manganese percentages, there are disparities in individual cases, especially as regards the degree of toughness or brittleness displayed by an alloy with certain percentages and with particular types of treatment. These differences are not always readily explainable.lb His data showed that alloys containing 4 to 10 per cent manganese water-quenched from Iooo°C. were brittle and hard with maximum brittleness at about 7 per cent. Slight improvement in ductility was obtained with compositions from 10 to 17 per cent manganese. Alloys containing up to 17 per cent manganese slowly cooled rather than quenched from 87o°C., he found, were slightly improved in ductility with significant improvement in alloys analyzing 4.1 and 4.8 per cent manganese. Recently Walters, Kramer and Loring2 reported mechanical properties for alloys made up from electrolytic manganese and ingot iron and containing from 0.02 to 0.04 per cent carbon. They showed that a tempering treatment at 54o°C. (Iooo°F.) for one hour significantly improved the ductility of compositions ranging from 6.7 to &apos; 20.7 per cent manganese. The differences of these compared with Hadfield&apos;s results they considered to originate in this tempering treatment plus the fact that Hadfield&apos;s alloys contained higher carbon and phosphorus (0.06 to 0.I5 per cent C; 0.06 to 0.07 per cent P compared with 0.02 to 0.04 per cent C, <o.ooI per cent P). In this paper it is shown that of the low-carbon alloys (0.02 to 0.03 per cent) containing from 3.3 to 21.5 per cent manganese moderately or rapidly quenched from IOOO°C. some are brittle or ductile, depending on presence or absence of hydrogen. Hydrogen is readily absorbed at high temperatures, and much of it is retained when the alloys are cooled to room temperature. The presence of hydrogen in the range of composition from 10 to 18 per cent manganese is a major factor in determining relative ductility. At 22 per cent manganese, and also at compositions below 10 per cent manganese, factors other than or in addition to hydrogen play a role. These are discussed. Also data are presented to show that hydrogen absorbed by the high-carbon alloys of Hadfield composition is without effect on their mechanical properties.

Jan 1, 1944

By Herbert H. Uhlig

Although the mechanical properties of high-carbon manganese-iron alloys, particularly the Hadfield manganese steels, have been established, the literature discloses discrepancies in the reported properties for the low-carbon alloys. Hadfieldla summarized the existing data up to 1927, including the investigations of Guillet, Arnold, Strauss, Burgess and Aston, and reported his own values for alloys containing for the most part from 0.06 to 0.I5 per cent carbon. He noted: From these comparisons it wil! be seen that while there is a broad and general agreement as to the character of the alloys at the different manganese percentages, there are disparities in individual cases, especially as regards the degree of toughness or brittleness displayed by an alloy with certain percentages and with particular types of treatment. These differences are not always readily explainable.lb His data showed that alloys containing 4 to 10 per cent manganese water-quenched from Iooo°C. were brittle and hard with maximum brittleness at about 7 per cent. Slight improvement in ductility was obtained with compositions from 10 to 17 per cent manganese. Alloys containing up to 17 per cent manganese slowly cooled rather than quenched from 87o°C., he found, were slightly improved in ductility with significant improvement in alloys analyzing 4.1 and 4.8 per cent manganese. Recently Walters, Kramer and Loring2 reported mechanical properties for alloys made up from electrolytic manganese and ingot iron and containing from 0.02 to 0.04 per cent carbon. They showed that a tempering treatment at 54o°C. (Iooo°F.) for one hour significantly improved the ductility of compositions ranging from 6.7 to &apos; 20.7 per cent manganese. The differences of these compared with Hadfield&apos;s results they considered to originate in this tempering treatment plus the fact that Hadfield&apos;s alloys contained higher carbon and phosphorus (0.06 to 0.I5 per cent C; 0.06 to 0.07 per cent P compared with 0.02 to 0.04 per cent C, <o.ooI per cent P). In this paper it is shown that of the low-carbon alloys (0.02 to 0.03 per cent) containing from 3.3 to 21.5 per cent manganese moderately or rapidly quenched from IOOO°C. some are brittle or ductile, depending on presence or absence of hydrogen. Hydrogen is readily absorbed at high temperatures, and much of it is retained when the alloys are cooled to room temperature. The presence of hydrogen in the range of composition from 10 to 18 per cent manganese is a major factor in determining relative ductility. At 22 per cent manganese, and also at compositions below 10 per cent manganese, factors other than or in addition to hydrogen play a role. These are discussed. Also data are presented to show that hydrogen absorbed by the high-carbon alloys of Hadfield composition is without effect on their mechanical properties.

Jan 1, 1944

By C. M. Loeb, A. M. Gaudin, J. H. Brown

R. E. Carter (General Research Laboratory, Schenec-tady, N. Y.)—Brown, Gaudin, and Loeb in their study of intergranular comminution by heating attempt to find one explanation for all types of rock in terms of the properties of the phases present. The only necessary condition for intergranular cracking by heating is the setting up of high stresses at the grain boundaries. Such stresses may be set up in multiphase isotropic mixtures if the thermal expansions of the phases are different, in non-cubic single phases because of the anisotropy of thermal expansion in the various crys-tallographic directions, and in materials containing quartz because of the a-p&apos; transformation at 575°C. In addition, for intergranular comminution by heating, the cooling and not the heating is most important.

Jan 1, 1960

By W. T. Turrall, D. Porter

THE crystal laboratory, Dept. of Physics, Massachusetts Institute of Technology, was confronted with the problem of obtaining a supply of optical grade calcium fluoride (CaF2) for use in growing synthetic CaFe2 crystals. A search of the known fluorspar deposits did not indicate that any quantity of optical spar could be obtained. Even the best material had to be sorted by hand to remove impurities. The process for growing CaF2 crystals developed by Professor D. C. Stockbarger of the Dept. of Physics, M.I.T., necessitates very pure feed materials. Exclusion of impurities is required, even in amounts detectable only spectrographically. The impurities occurred as minute inclusions of SiO2, BaSO4, CaCO3, FeS2, water or air. Crystals up to 4 in. in diam and weighing several pounds are made by the Harshaw Chemical Co. in Cleveland. Since the time required to grow a 4-in. crystal is about one week, and since the cost of manufacture is high, removal of impurities by any concentration method appeared practical. The mineral engineering section of the Dept. of Metallurgy undertook to investigate the possibility of concentrating clear optical fluorspar, -4 mesh +10 mesh, from a feed containing over 99 pct CaF2. Various innovations of the known methods of concentration were considered, but in each case the minute amount of impurities associated with the crystal produced such extremely small differences

Jan 1, 1952

By Louise B. Freeman

Kentucky for the first time in its oil history passed the 10 million barrel mark. Of the total 10,019,641 bbl., 8,262,516 bbl. were produced in Western Kentucky, and Union County surpassed all others, with 4,056,142 bbl., or 40 percent of all the production for the state. There were 930 wells known to have been drilled during the year; 510 in Western Kentucky and 221 in the gas-producing area of Eastern Kentucky.

Jan 1, 1946

By W. D. Kruger

Methods for analyzing flooding or cycling projects by means of two-dimensional flow calculations are presented in the literature. The use of these methods allows the determination of optimum operating conditions for such projects and provides information on pattern efficiencies, relative flow rates, pressure distributions and floodout histories. The accuracy of such analyses depends on the basic reservoir data employed, especially the absolute permeability distribution in the reservoir; however, absolute permeability data normally are determined from well flow tests and/or core measurements and are so limited in quantity and quality that they do not adequately describe the reservoir flow properties. A calculation procedure is presented for determining the areal permeability distribution in the reservoir. Use of the procedure allows verification of the basic reservoir data through the matching of past reservoir conditions, thereby providing proper data for reliable predictions of future operations. The calculation procedure is a numerical technique based on a mathematical model of the reservoir and is designed for solution by means of an electronic digital computer. Results from field application of this procedure are presented. Permeability distributions from measured data are compared to those calculated to indicate the need for the analysis. Comparisons of field-measured and calculated pressure distributions are given to establish the validity of the calculation procedure. The conclusions of this paper are (I) use of the calculation provides data that allow a match of past reservoir conditions and thus reliable prediction of future operations; and (2) the procedure should, where applicable, be used to provide adequate reservoir data for use in two-dimensional flow calculations and related reservoir analyses. INTRODUCTION One means of providing more precise engineering control over reservoir operations during all stages of depletion is to develop some type of model to simulate the reservoir, using information developed from the behavior of the prototype to predict the performance of the actual reservoir. The use of mathematical rather than physical models for this purpose has been gaining in importance recently because of the application and availability of electronic computers. Mathematical models avoid instrumentation difficulties and allow easier handling of large-scale problems. At present, analyses employing two-dimensional models are common, and thought is being given to the use of models in three dimensions. The use of multi-dimensional models is necessary to show not only what is occurring in the reservoir, but also where in the reservoir the phenomena of interest are taking place. Methods for analyzing flooding or cycling projects by means of two-dimensional numerical models are presented in the literature. The use of these methods allows the determination of optimum operating conditions for such projects and provides information on pattern efficiencies, relative flow rates, pressure distributions and floodout histories. The applicability of numerical models and the results of using such analyses have been presented through field examples. The references indicated here discuss fully the data necessary to build the mathematical reservoir model and the way the model is used to study or predict the future performance of the reservoir. The accuracy of the analysis of such projects depends on the basic reservoir data employed in the construction of. the model. In order to be sure the model represents the reservoir, it must be used to match some known set of reservoir conditions, i.e., to match past reservoir performance. The accuracy of the model is directly dependent upon the absolute permeability distribution in the reservoir; however, absolute permeability data are normally determined from well flow tests and/or core measurements, and are so limited in quantity and quality that they do not adequately describe the reservoir flow properties. There is always the need for better data and for verification of existing data. The purpose of this paper is to show the use of the mathematical model to match past performance in flooding or cycling projects, the use of numerical techniques to adjust the basic absolute permeability data if necessary so that a match is obtained, and in this way to generate the effective areal permeability distribution of the reservoir. A review of the basic concepts of the numerical model will be given, followed by a discussion of the data-adjusting technique for matching past performance. TWO field examples will be cited to show

By Walter S. Weeks

CONFUSION appears to exist in the discussions of fan testing because engineers do not agree on what energy should be credited to the fan in certain cases, and because certain terms that are used in the discussions seem to have double meanings. The purpose of this paper, therefore, is to discuss the useful energy that should be credited to the fan and the methods of determining this energy, and to suggest changes in nomenclature for the sake of clearness. The instruments commonly used in the measurement of fan pressures are the manometer, the static tube, and the impact tube. The static tube is a tube with small pinholes in it. When connected to one leg of the manometer and placed in the air current with the holes facing at right angles to the direction of the current, this tube causes the manometer to register the static pressure, unaffected by the impact of the air. The impact tube is a tube with an opening that faces the air current. When connected to one leg of the manometer, this tube causes the manometer to register a pressure which is the static pressure modified by the impact of the flowing&apos; air on the end of the tube. If the static tube is connected to one leg of the manometer and the impact tube to the other leg, and both instruments are inserted close together in the air current, the static pressure is eliminated and the manometer registers the impact pressure. The efficiency of a fan is the percentage of the expended power utilized in useful work. The items to be included as useful work are a matter of convention, and as the conventions are not universal I feel that the matter is open to discussion.

Jan 1, 1929

E. E. BACH, Ellsworth, Pa.-A personal interview with a man is one factor in reducing labor turnover; his working conditions is another, while the conditions under which lie brings up his family is still another; all have much to do with the reduction of labor turnover. A man well placed, happy in his work and happy in his home, will stay put and incidentally decrease the labor turnover in any industry. C. R. HOOK, Middletown, Ohio.-I am so deeply and sincerely interested in the employment problem, that it is very difficult for me, once I get started, to know when to, stop. In the first place, I want you to understand that I realize that what may be a possible accomplishment in the plant with which I happen to be connected, may not be possible of accomplishment in the same way in your plant. Our problems might be quite different; our location might be quite different, and therefore our employment problem would be very much affected by the community conditions. Two of our plants happen to be located in a town of about

Jan 4, 1918

By M. Perišic

Requirements concerning determination of geometric characteristics and estimate of reserves and grade may in various mineral deposits significantly differ and by no means can be completely envisaged. Therefore, program writing which would in advance meet all requirements is from a practical point of view impossible. Programming for each particular project is also unacceptable solution, due to many facts, among which is ever growing scope of work and the terms to be met. Therefore, conventional method of programming proved to be ineffective. The team of the Mining Institute experts came to the conclusion that the solution of facing problems lies in the idea of introducing specialized programs, instead of complex ones. Each of them represents a functional entirety. Procedure of complete mineral deposits computer processing is described by a problem-oriented programming language which was designed for that particular application. One or more than one specialized programs are called by one instruction so that the program in that language can have a few hundred time less instructions than an equivalent FORTRAN program. Besides description of the program system and programming language the paper also covers some aspects of its application in solving complex problems.

Jan 1, 1977

By C. M. Smith

DELEGATES from 26 Local Sections and- Divisions of the Institute had three stimulating sessions during the Annual Meeting, a few topics still remaining to be discussed after the two Monday sessions.. The final session was held on Thursday morning. An abstract of the discussion will be transmitted to each delegate present. The topics included: Student relations. Section operation, membership, employment, MINING AND METALLURGY, a new nonmetallic minerals Division. licensing of engineers, and increased allotments of money to Local Sections. Some of the Sections felt that the present limit of $250 allotted to them - from the national treasury was insufficient to carry on their activities, and that this maximum should he increased. A resolution to this effect was passed for transmission to the Board of Directors.

Jan 1, 1935

By Henry J. Williams

The main difficulty in the determination of silicon in pig-irons containing very high percentages of that element, has been due to their almost complete insolubility in acids, or mixtures of acids. The object of the present paper, which presents no new principle, is to suggest a method of determination which has repeatedly given accurate results, and which obviates completely the tediousness and uncertainty of the usual slow solution in acids. This method has been tried with pig-irons containing from 7 to 14 per cent. of combined silicon, and properly called ferro-silicons. When reduced to an impalpable powder in the agate mortar, an 11 per cent. ferro-silicon was found to resist the action of all acids, or mixtures of acids, with the exception of sulphuric acid of about 1.25 specific gravity. But the action of this acid, even during long continued heating, was very slow, 72 hours being necessary to com pletely dissolve half a gramme of the metal. The complete decomposition of 1 gramme of the metal may, on the other hand, readily he effected in a few minutes by fusion with sodium carbonate in a covered platinum crucible over a blast-lamp —the idea being to dissolve the silicon, leaving the iron in condi tion to be readily attacked by acids. The silicon dissolves as soluble sodium silicate, and metallic iron remains in a very spongy and finely divided condition. The addition of a little hot water

Jan 1, 1889

By C. T. Liu, J. Gurland

The deformation behavior in tension of spheroidized carbon steels was studied at room temperature as a function of carbon content, 0.065 to 1.46 wt Pct, and carbide particle size, 0.88 to 2.77 p. It was found that the Hall-Petch strength-grain size relation is directly applicable to the yield and flow stresses of the two lower-carbon steels , 0.065 and 0.30 pct C. The strength data for the medium- and high-carbon steels, 0.55 to 1.46 pct C, also satisfied the Hall-Petch relation, provided that these data are based upon the particle spacing. Beyond 4 pct strain, the flow stress data of all the steels studied could be represented by the same Hall-Petch relation with dinerent spacings for grain boundary and particle strengthening. The behavior of the higher-carbon steels was consistent with the postulated formation of a dislocation cell network during processing and initial deformation (up to 4 pct strain). The cell size was assumed to be equal to the planar particle spacing. The true stress at the ultimate tensile strength was also found to be a function of the particle spacing. At a given temperature and strain rate, the yield and flow stresses of carbon steels depend on the type and dimensions of the microstructure. Starting with the work of Gensamer et al. in 1942,&apos; experimental studies on pearlitic and spheroidized carbon steels revealed that the strength of steels is a function of two main parameters: the ferrite grain size2&apos;3 and the carbide particle spacing;1&apos;4&apos;5 on this basis, two different strengthening mechanisms have been developed to apply to steels of low and high carbon contents, respectively. In polycrystalline iron and mild steels the grain boundaries are regarded as the major structural barriers to slip. The relation between strength and grain size is generally represented by the Hall-Petch equation which is based on a linear proportionality between strength and the inverse square root of the average grain size.2&apos;3y677 However, Gensamer et al.&apos; and Roberts et related the yield strength of medium -and high-carbon steels to the carbide particle spacing alone, and they found a linear relation between the logarithm of the mean free path in the ferrite and the yield strength in both spheroidized and pearlitic steels. By means of the electron microscope, Turkalo and LOW&apos; extended the study to finer structures; they concluded that the logarithmic relation is not valid for the entire range of microstructures unless grain boundaries are also included in the measurement of the mean free path. For the specific case of spheroidized steels, Ansell and aenel&apos; found that the yield strength data,4&apos;5 when plotted as a function of mean free path, fit the Hall-Petch equation; however, T&apos;ysong found that the same data fit the 0rowanl0 relation if a planar inter-particle spacing is used. Recently Kossowsky and ~rown" studied the strength of prestrained spheroidized steels, 0.48 and 0.95 pct C, and concluded that the strength due to the carbide dispersions varies linearly with the reciprocal of the square root of the mean free path between carbide particles and dislocation networks. Such networks were first observed by Turkalo." The conclusion common to all these studies is that the available slip distance in the ferrite is the most important variable in determining strendh. Previous work on carbon steels is restricted to limited composition and strain ranges. The mechanism which governs the flow properties is not clearly understood, and, in particular, little is known about the composition dependence of the transition between grain boundary strengthening and particle hardening. The purpose of the present work is to investigate the strengthening mechanism in spheroidized steels over a wide range of carbon content, 0.065 to 1.46 wt pct, and plastic strain, yielding to necking. The spheroidized structure was chosen because of its relative simplicity and the relative ease of control and measurement of the structural parameters. The experimental work is limited to tensile testing at room temperature at constant extension rate. The effects of the carbide particles on the fracture behavior of spheroidized steels are discussed elsewhere.13 EXPERIMENTAL PROCEDURE Eight different grades of vacuum-cast carbon steels were supplied in the form of forged and rolled plate by the Applied Research Laboratory of the U.S. Steel Corp. The compositions furnished with these steels are given in Table I; the carbon content ranges from 0.065 to 1.46 wt pct, or from 1.0 to 22.3 vol pct of carbide. The steel plates were cut transversely into rods a little larger than the test specimens, 1 in. gage length, i in. diam. The rods were austenitized in air (enriched with CO by a consumable carbon-rich muffle) at 50° C above theA, orA., temperature for 2 hr and then quenched in oil with vigorous stirring. The as-quenched rods were tempered in two stages in order to obtain the desired distributions and sizes of carbide particles. The rods were first tempered at 460° C for 10 hr and then at 700" C for periods ranging from 4 hr to 3 days, in vacuum. After final machining, all specimens were vacuum-annealed again at 650°C for 1 hr in order to relieve residual stresses. The tension tests were carried out in two steps. The initial part of the load-strain curve, up to about 2 pct strain, was determined on a Riehle testing machine with an extensometer of small strain range, 4 pct strain, in order to obtain the yield and initial flow piopertiesi As soon as the first part of the test was finished, the specimen was placed in an Instron testing machine equipped with a strain gage extensometer with a maximum strain range of 50 pct. The load-strain curve to fracture was

Jan 1, 1969

By E. T. Turkdogan, Klaus Schwerdtfeger, P. Grieveson

The rate of growth of "Fe4N" on a iron was measured by nitriding purified iron strips in flowing am -monia -hydrogen gas mixtures at 504" and 554°C. It is shown that a dense nitride layer is formed when a zone -refined iron is used in the experiments. With less pure iron, the nitride layer is found to be porous. Through theoretical treatment, the self-diffusivity of nitrogen is evaluated porn the parabolic rate constant, and found to be essentially independent of nitrogen actirlity, e.g., D* = 3.2 x l0-12 and 7.9x l0-12 sq cm per sec at 504" and 554?C. Some consideration is given to the mechanism of diffusion in the nitride phase. THERE is a great deal of background knowledge on the solubility and diffusivity of nitrogen in iron, and on the thermodynamics and crystallography of several phases in the Fe-N system. Although case-nitrided steels have many applications in practice, no work seems to have been done on the diffusivity of nitrogen in the iron nitride, ?&apos;, phase. The only work reported on the related subject of which the authors are aware is an investigation by Prenosil,1 who measured the growth rate of the e phase on iron by nitriding in ammonia-hydrogen gas mixtures. EXPERIMENTS Purified iron plates of approximate dimensions 1 by 0.5 by 0.03 cm were nitrided in flowing mixtures of ammonia and hydrogen, in a vertical furnace fitted with a gas-tight recrystallized alumina tube. After a specified time of reaction, the sample was cooled to room temperature by withdrawal to the water cooled top of the reaction tube. The furnace temperature was controlled electronically in the usual manner within *l°C; the temperature was measured using a calibrated Pt/Pt-10 pct Rh thermocouple. For each experiment the iron strip sample was cleaned with fine emery cloth and degreased with tri-chloroethylene prior to the experiment. The ammonia-hydrogen gas mixtures were prepared from anhydrous ammonia and purified hydrogen using constant pressure-head capillary flowmeters. The gas mixture flowed upward in the furnace with flow rate of 400 cc per min at stp. The composition of the gas mixture was checked by chemical analysis at regular intervals. In most cases, the compositions of the exit gas and metered input gas agreed within about 0.3 pct, indicating that cracking of ammonia did not pose a problem at the temperatures employed. Two series of experiments were carried out using two different types of purified iron samples. In the first series of experiments at 550°C, vacuum carbon deoxidized "Plastiron" was used. The main impurities present in this iron were, in ppm: 4043, 50-Cr, 20-Zr, 40-Mn, 20-P, 20-S, 20-C, 50-0, and 10-N. In these experiments the rate data were obtained by measuring the change in weight of the iron specimen suspended in the hot zone of the furnace by a platinum wire from a silica spring balance. The nitride layer formed in these experiments was found to be porous, particularly near the outer surface. In other experiments, high purity zone-refined iron (prepared in this laboratory) was used. The total impurity content of this iron was 30 ppm of which 20 ppm was Co + Ni, 4 ppm 0, other metallic impurities were less than 1 ppm. The zone-refined iron bar, -2.5 cm diam, was cold rolled to a thickness of about 0.03 cm and the specimens were prepared for the experiment as described earlier. After the nitriding experiment, the sample was copper plated electro-lytically and mounted in plastic for metallographic polishing. After polishing, the thickness of the ?&apos; layer was measured using a metallographic microscope. The nitride layer formed on the zone-refined iron was essentially free of pores. RESULTS The different morphology of the nitride layers grown on "Plastiron" and zone-refined iron is shown in Fig. 1. Both samples were nitrided side by side for 55 hr. The holes in the less pure iron, Fig. l(a), are confined to a region about one half thickness from the outer surface. The dense layer grown on zone-refined iron, Fig. l(b), is thinner than the porous layer on the "Plastiron". The impurities in the iron are believed to be responsible for the formation of a porous nitride layer. The pore formation may be due to the high nitrogen pressures existing within the nitride layer, e.g., the equilibrium nitrogen pressure is 1.2 x l05 atm in the 38.6 pct NH3-61.4 pct H2 and 6.6 x l03 atm at the Fe-Fe4N interface at 554°C and 0.96 atm. It is possible that the oxide inclusions present in the electrolytic iron may facilitate the nuclea-tion of nitrogen gas bubbles within the nitride layer. Support for this reasoning is the fact that pores are only encountered in the outer range of the layer where nitrogen pressures are largest. The photomicrographs in Fig. 2 show the effect of reaction time on the thickness of the dense nitride layer formed on zone-refined iron. These sections are from samples nitrided in a stream of 29 pct NH3-71 pct H2 mixture at 554°C for 22, 70, and 255 hr. In all the sections examined the nitride-iron interface was noted to be rugged. These irregularities are be-

Jan 1, 1970

By K. D. Jacob, H. L. Marshall, D. S. Reynolds

All types of commercial phosphate rock produced throughout the world contain fluorine in quantities ranging from approximately 0.4 to 1.3 per cent in the Curacao and Christmas Island phosphates to 3.1 to 4.2 per cent in the phosphates of the United States and North Africa1. For a given type of rock, the fluorine content is usually roughly proportional to the phosphorus content. Significance of Fluorine in Phosphate Rock On the basis of chemical and X-ray diffraction studies, Hendricks and co-workers2 concluded that fluorapatite, Cal10F2(PO4)6, is the essential phosphatic constituent of the commercial types of domestic phosphate rock. On the other hand, Bredig and co-workers3 have recently advanced the opinion, also based on X-ray diffraction studies, that the mineral phosphates usually contain carbon dioxide in the apatite lattice, and that the phosphate rocks of the United States are really fluorcarbonate apatites. However, the domestic types of phosphate rock do not seem to differ greatly from coarsely crystalline fluorapatite in their behavior toward chemical reagents in general, and for the purpose of this paper it will suffice to consider fluorapatite as being the essential phosphatic constituent of these types of rock. The available data1 indicate that the different commercial types of domestic phosphate rock usually contain about 12 to 52 per cent more fluorine than theoretically is required to form fluorapatite with all the phosphorus. Calcium fluoride (fluorite) has been definitely identified in only a very few of the samples that have been examined1,2. Bredig and co-workers4 state that fluorapatite can take into its crystal lattice excess calcium fluoride to the extent of approximately 70 per cent of that theoretically required by the formula Ca10F²(PO4)6 without causing more

Jan 1, 1938

By D. S. Reynolds, K. D. Jacob, H. L. Marshall

All types of commercial phosphate rock produced throughout the world contain fluorine in quantities ranging from approximately 0.4 to 1.3 per cent in the Curacao and Christmas Island phosphates to 3.1 to 4.2 per cent in the phosphates of the United States and North Africa1. For a given type of rock, the fluorine content is usually roughly proportional to the phosphorus content. Significance of Fluorine in Phosphate Rock On the basis of chemical and X-ray diffraction studies, Hendricks and co-workers2 concluded that fluorapatite, Cal10F2(PO4)6, is the essential phosphatic constituent of the commercial types of domestic phosphate rock. On the other hand, Bredig and co-workers3 have recently advanced the opinion, also based on X-ray diffraction studies, that the mineral phosphates usually contain carbon dioxide in the apatite lattice, and that the phosphate rocks of the United States are really fluorcarbonate apatites. However, the domestic types of phosphate rock do not seem to differ greatly from coarsely crystalline fluorapatite in their behavior toward chemical reagents in general, and for the purpose of this paper it will suffice to consider fluorapatite as being the essential phosphatic constituent of these types of rock. The available data1 indicate that the different commercial types of domestic phosphate rock usually contain about 12 to 52 per cent more fluorine than theoretically is required to form fluorapatite with all the phosphorus. Calcium fluoride (fluorite) has been definitely identified in only a very few of the samples that have been examined1,2. Bredig and co-workers4 state that fluorapatite can take into its crystal lattice excess calcium fluoride to the extent of approximately 70 per cent of that theoretically required by the formula Ca10F²(PO4)6 without causing more

Jan 1, 1938

Jan 1, 1923

Jan 1, 1923

By J. G. Eberhort

ThE literature of surface phenomena shows that, except for most of the rare-earth elements, surface tensions have now been determined for almost every liquid metal. The situation for liquid metal oxides is, in contrast, characterized by a great scarcity of surface-tension data. A surface-tension correlation between these two classes of substances has been found which provides a means of estimating unknown liquid-oxide surface tensions from the corresponding known liquid-metal surface tension. Lf the surface tension of the liquid metal is a(M) and that of the liquid metal oxide is o(M,Oy), then oxides of all stoichiometries can be brought into one correlation if is plotted against with the surface tensions taken at the respective melting points. The available data is displayed in this fashion in Fig. 1 where the relationship between the surface tensions of the two classes of liquids is found to be The correlation in Fig. 1 is based on data found for nine liquid metal oxides and the corre- sponding liquid metals In cases where several sur-face-tension determinations were available on the same substance, higher values were generally favored over lower ones because they usually indicate greater Sample purity. All of the metal-metal oxide pairs are in good agreement with Eq. [I] except for B-Bz03. The reason for the departure of this pair from the correlation is not understood. To estimate the surface tension of other liquid metal oxides the corresponding liquid-metal surface tension must be found. A nearly complete bibliography of the surface tension of liauid elements is available in the 46th edition of the Handbook of Chemistry and physics. Some additional references on metals are included here for convenience Se,26Sr,&apos;?ThanduZ5). It is also possible to estimate the surface tension of a solid metal oxide or metal from the corresponding liquid-state data. As a liquid material is cooled through its melting point the surface tension increases abruptly by an amount Ao. bondi&apos; has estimated that the maximum value of Aa at the melting point is Ao = Ahf/A [2] where Alzf is the heat of fusion per atom and A is the area per atom in the interface. Thus with heat of fusion and crystallographic data the surface tension of a solid at the melting point can be estimated as o + Ao.

Jan 1, 1967

By T. R. Armstrong

Total crude oil production in Mexico in the year 1941 is estimated at approxi- mately 41,000,000 bbl.; a daily average of 112,700 bbl. and a decrease of about 5 per cent as compared with the daily average of 120,000 bbl. produced in the year 1940, and nearly 11 per cent decrease as com-

Jan 1, 1942

By T. R. Armstrong

Total crude oil production in Mexico in the year 1941 is estimated at approxi- mately 41,000,000 bbl.; a daily average of 112,700 bbl. and a decrease of about 5 per cent as compared with the daily average of 120,000 bbl. produced in the year 1940, and nearly 11 per cent decrease as com-

Jan 1, 1942