Search Documents

By K. N. Han, H. Lee, M. C. Fuerstenau

An investigation of the recovery of finely-divided cassiterite and silica particles less than 1 µm (1200 mesh) in size has been carried out using packed and fluidized beds. The bed particles used included cassiterite and silica particles ranging from 44 to 210 µm (325 to 70 mesh). Effects of various system parameters on the recovery and selectivity of cassiterite fines were investigated. System parameters included pH of the slurry solution, superficial velocity, slurry concentration, and bed particle sizes. High recoveries of cassiterite fines were obtained at pH 4.0 and slow slurry flow rates. In a packed bed system, recovery of cassiterite fines was greater than 95%, while that of silica fines under the same conditions was about 35%. Although the total recovery per pass is not as good as the packed bed, the fluidized bed system exhibits good recovery in general and an excellent selectivity of cassiterite fines. There is an optimum superficial velocity, vo, for the rate of fine particle uptake and the apparent rate constant has the form of Kvo1/2- K'vo, where K and K' are system constants.

Jan 1, 1985

By C. C. Herrick

The vapor pressure of indium has been measured by the torque-effusion technique, as a function of temperature between 1102o and 1422oK. For liquid indium, the vapor pressure (in atmospheres) can be represented by the equation -R In P = 5.782 x104/T - 25.29from 1000o to 1422oK. Extrapolation yields a calculated normal boiling point of 2329°K and a heat of vaporization at 298 oK of 58.09 kcal per mole by the third-law method and of 58.39 kcal per mole by the second-law method. Calculations indicate that the free-energy functions of Hultgren are to be preferred to those of Guruich. BECAUSE of the potential uses of liquid metals, it is important that convenient experimental methods be developed which will lead to a sufficient body of thermodynamic data so that reasonable estimates of properties of liquid metals can be made. Indium is particularly well-suited to investigation, since it remains liquid over a long temperature interval, it alloys readily, suitable containers for it are easily procured, and relatively few investigations of its thermodynamic properties in the region above 1000°K have been made. PREVIOUS RESEARCH The first determination of the vapor pressure of indium was made by Anderson,' using the Knudsen method and silica-lines stainless-steel cells. Kohlmeyer and spandau2 determined the normal boiling point, and a mass-spectroscopic investigation has been made by Lyubimov and Lyubitov.3 (Unfortunately, only an equation representing the data of the latter investigators has been available to us.) Hultgren et al.4 and Gurvich5 have published discordant tables of the free-energy functions for indium. EXPERIMENTAL METHOD The torsion-effusion principle has been described amply in the literature.8,7 With this method, one observes the angular deflection induced by effusion of vapor from a multihole effusion cell which is suspended from a filament producing a small rotational restoring force. The pressure within the effusion cell can be computed from the relation ziaifiai where k is the torsion constant of the filament, 6 is the observed angular deflection, and ai, fi, and qi are the area, force factor, and moment arm of the ith effusion orifice. The force factor f is analogous to the Clausing factor,' and corrects for the reduction in effusive force attributable to the finite geometry of the effusion orifice. Schultz and Searcy' have tabulated the force factors for various tube geometries. EXPERIMENTAL APPARATUS The physical arrangement employed in this study is shown in Fig. 1. The furnace elements are six Globar heat rods with 15-in. hot zones. Temperature is maintained to * 1°K by a Beck mechanism driving two 26-amp Powerstats in parallel. A Pt (Pt, Rh 10 pct) thermocouple serves as the sensing element. Four inner tubes act as vibration isolators; the air pressure required for maximum isolation was determined empirically, and is maintained by a solenoid valve. The tungsten fiber, 9 by 0.002 in., is joined to an 0.008-in. tungsten wire or graphite rod via a machined lightweight chuck.

Jan 1, 1964

By AIME AIME

AMONG the recent mining and metallurgical developments in England great interest has been shown in the development of an iron-ore field covering 26,0.00 acres in Northamptonshire, containing 500,¬000,000 long tons of ore; and the erection at Corby, by Stewarts & Lloyds, of a modern basic bessemer steel plant and tube works. The entire project was planned to cost about £3,300,000. Many improvements have been made in the varied equipment that is being installed, some of which has set mew records for massiveness. There is, for instance, a new roll crusher, which has been manufactured by Hadfields, Limited, of Sheffield, the largest ever built in England, and weighing 130 tons. This machine, shown in Fig. 1, as erected at the Hadfields shops, is primarily designed to take blocks of iron ore as they come from the steam shovel. The maximum size is 54 by 48 by 36 in., hut occasional pieces slightly larger than this may be accommodated. The capacity is upwards of 500 tons per hour, the product passing to a secon-

Jan 1, 1934

By T. F. Witherbee

It is proposed to give, first, a description of the works; second, a report of the first six months of the present blast; and third, such improvements as have been suggested by the practical working. The site selected for this furnace was, at the time of commencing work, October, 1872, entirely covered by the navigable waters of Lake Champlain. A coffer-dam was first built of cribs of round timber filled with stone, forming three sides, while the shore answered for the fourth. Considerable excavating was done with a steam-dredge, a hole being left for it to pass out. The opening was then built up, and the cribbing banked up with blue clay from the bottom of the lake, to render it water-tight and the dam pumped out; the remainder of the excavating being done by hand. All of the foundations, with the exception of the elevator-tower, and fifteen feet of the east side of hot blast, rest on the Potsdam sandstone, which forms the shore line, dipping into the lake at an angle of fifteen degrees. Owing to jogs in the formation, a much greater depth was found necessary than was at first anticipated, the foundation under the stack

By T. F. Witherbee

IT is proposed to give, first, a description of the works ; second, a report of the first six months of the present blast; and third, such improvements as have been suggested by the practical working. The site selected for this furnace was, at the time of commencing work, October, 1872, entirely covered by the navigable waters of Lake Champlain. A coffer-dam was first built of cribs of round timber filled with stone, forming three sides, while the shore answered for the fourth. Considerable excavating was done with a steam-dredge, a hole being left for it to pass out. The opening was then built up, and the cribbing banked up with blue clay from the bottom of the lake, to render it water-tight and the dam pumped out; the remainder of the excavating being done by hand. All of the foundations, with the exception of the elevator-tower, and fifteen feet of the east side of hot blast, rest on the Potsdam sandstone, which forms the shore line, dipping into the lake at an angle of fifteen degrees. Owing to jogs in the formation, a much greater depth was found necessary than was at first anticipated, the foundation under the stack

Jan 1, 1876

By Elmars Ence, Harold Margolin

The Ti-Fe and Ti-Fe-0 systems were re-examined because of the controversy regarding the existence of Ti2Fe, and to consider all available data points to the existence of Ti,Fe. The Ti-Fe-0 system contains two ternary compounds: E, corresponding to Ti2Fe; and y. SEVERAL authors have investigated the constitution of titanium-rich alloys of the Ti-Fe system. The most extensive study of titanium-rich portions of the Ti-Fe system was by Van Thyne, Kessler, and Hansen,' who investigated this system up to 50 pet Fe and used the highest purity materials available for their alloy preparation (iodide titanium was used for alloys up to 20 pet Fe). According to Van Thyne et al., phase relationships in the region of investigation are governed by phases a,ß, and TiFe. No evidence of an intermetallic compound Ti,Fe was found. although earlier. works by Laves and Wallbaum,' and Duwez and Taylor' reported its existence. Rostoker's study on the occurrence of TilX phases" confirmed the findings of Van Thyne et al. Rostoker proposed that the compound Ti Fe found by Duwez does not exist but is actually a ternary compound, Ti1Fe3O, originated by inadvertent oxygen contamination. The partial isothermal section of the ternary Ti-Fe-0 system as reported by Rostoker' seems to confirm this explanation. In the course of phase diagram work conducted at New York University, however, certain irregularities were observed to be associated with ternary systems of the type Ti-Fe-X. The ternary phase 6, observed in the systems Ti-Fe-Mo' and Ti-Fe-V." was found to be structurally identical to the com-pound Ti2Fe as reported by Duwez and Taylor, and to Rostoker's compound Ti1,Fe2O. Since the amount of oxygen possibly present in the Ti-Fe-Mo and Ti-Fe-V systems could not account for the observed amounts of the compound, it appears that the d phase in these systems is not Ti,Fe,O. On the other hand, considering the amounts of the 6 phase, particularly in the Ti-Fe-Mo system, the location of the phase was uncertain. It was felt that the introduction of the Ti2Fe phase would alleviate some of the inconsistencies of the two systems. Because of the uncertainties relating to the phase Ti2Fe, or Ti1Fe2O, it appeared worthwhile to re-examine the Ti-Fe and Ti-Fe-O systems in the vicinity of these compounds with highly sensitive metallographic techniques and with X-ray methods. Experimental Procedure Alloy Preparation—For the study of the binary system four alloys were prepared, containing 26.9 (30 wt pct), 34.0 (37.5 wt pet), 41.2 (45 wt pet), and 56.3 (60 wt pet) atomic pet Fe, and for the ternary Ti-Fe-O system 18 alloys were prepared in the composition range of 1.6 to 16.9 atomic pet 0 and 24.3 to 55.7 atomic pet Fe. The materials used for the Ti-Fe alloys were iodide titanium (99.98 pet Ti, 0.002 pet 0) and Ferro-vac-E iron (99.95 pet Fe, 0.0052 to 0.0072 pet 0). For the Ti-Fe-O study the materials used were sponge titanium containing less than 0.06 pet 0, Ferrovnc-E iron, and Baker's analyzed TiO2. The nominal weight and atomic percentages of the ternary alloys prepared are shown in Table I. Melting—Charges of 10 to 15 g were melted in a nonconsumable arc furnace in argon atmosphere according to the technique described elsewhere.'" Since there was practically no weight loss through the various stages of melting and oxygen losses have not been observed previously, it appeared justifiable to use nominal composition for interpretation of data. Iodide titanium control buttons, of the same mass as the Ti-Fe charges, and melted under the same conditions, were used to check hardness pickup during melting. A hardness increase of 2 to 3 Vhn was found. Heat Treatment—The specimens were annealed in quartz capsules under argon. To avoid contact between the specimen and capsule material all specimens were wrapped in titanium sheet. The annealing times are given in Table 11. The attain-

Jan 1, 1957

By Kidd, Robert L.

INASMUCH as galena and sphalerite flotation concentrates are being produced that contain over 95 per cent galena or sphalerite, it is not unreasonable to believe that a flotation concentrate assaying at least 80 per cent of native gold can he secured provided the gold is free. As yet, little if any fundamental information has been published concerning the flotation of free gold either alone or in the presence of sulfides. So far, we are unable to make as complete a separation of gold from sulfide minerals by flotation as is possible in, the separation of one sulfide from another by this method. An introductory study of the flotation of several free gold ores has been made in our Utah laboratories. For this study three general types of gold ores were chosen, namely: (1) Quartzite containing 0.26 oz. gold per ton in which no base metals are present; (2) sulfide ore (2.04 oz. Au; 1.31 oz. AO containing pyrite as the only sulfide present and the gold free; and (3) oxidized ore (1.10 oz. Au; 0.70 oz. Ag) from an oxidized zone of the vein from which sulfide ore (No. 2) was taken; little sulfide iron was present.

Jan 1, 1932

By Fred C. Bond

SIX years have passed since the last grindability table was published.' In that time the list has been increased with many new tests, and the development of the new Third Theory of Comminution2 has made possible the reduction of all results to a consistent work index value. In this tabulation all grindability and crushability test results are given in terms of the work index, with formulas for reversion to the older units if desired. The average values for 57 different classes of materials are listed in Table I. The total number of work index values listed is 1211, and the overall average work index is 14.42. The complete tabulation, with each test listed alphabetically both under material type and under company name, can be obtained by writing to the Allis-Chalmers Manufacturing Co., Processing Machinery Department, Milwaukee 1, Wisconsin. The work index Wi is the calculated total work input in kilowatt-hours per short ton required to re- duce from theoretically infinite particle size to 80 pct passing 100 microns, or to approximately 67 pct passing 200 mesh. The work inputs required per ton for the same size reduction of different materials are directly proportional to their work indexes, and according to the Third Theory the work input per ton is inversely proportional to the square root of the diameter of the product particles. Where W represents the work input in kilowatt hours per ton, where F is the feed size, or diameter in microns of the square hole which 80 pct of the feed passes, P the product size, or microns which 80 pct of the product passes, and Rr the reduction ratio F/P, the work index Wi is found from Rr-l 100 When the work index Wi is known, the work input W required to reduce from any feed size F to any product size P is found from W = Wi ( Rr- 1 100

Jan 1, 1954

By D. F. Hewett

ALTHOUGH most persons will agree that an individual or a nation can profit from the experience of other individuals or nations, there is always room for debate over the degree of similarity of their past and present conditions and of their future problems. Noting the increasing interest that Americans are showing in our mineral problems, I have felt that we could profit from reviews of the experiences in mineral exploitation acquired by the industrial nations of Europe. Whether we can learn much from Europe's experience in exploiting such minerals as petroleum may be debatable, but certainly, with a record of metal production extending back nearly 3000 years, Europe should hold much of value for America. A trip to Europe in 1926 permitted me to visit 28 mining districts, of which about half are now or have been in times past outstanding sources of several metals. The districts range from England to Greece and from Spain to Poland. To summarize briefly my impressions of these mining districts, as well as such reactions to the thought and life of Europe as so short a visit permits, I shall only venture the opinion that Americans can review with great profit the ideas and actions of Europeans, with regard not only to the production of metals but to many expressions of life. I believe that America has made and is making new contributions to the art of living, as well as to the arts of mining and metallurgy, but in so far as Europe is and has been a laboratory of economic, social and political experiments, the results she has attained deserve the thoughtful attention of America. I have come to believe that many of the problems that harass Europe lie in our path not far ahead. I have therefore hoped that a review of metal production in Europe in the light of its geologic, economic and political background may -serve to clear our vision with regard to our own metal production.

Jan 1, 1929

By HOMER L. WILLIAMS

WHILE some of the mining companies have been pumping a small amount of water for some time, it is only in recent years that large quantities of water have been encountered in the Tonopah district. The water appears to be in different zones or belts so that the draining of one property does not necessarily affect the one adjoining. Consequently, each company has its own pumping plant and its own conditions. The companies panes handling the largest amount of water are the Tonopah Extension Mining Co., Halifax Tonopah Mining Co., West Tonopah Consolidated Mining Co., and Great Western Consolidated Mining Co. The Halifax shaft is on the eastern end of the district and the other three properties on the western. The ore-bearing formation occurs at greater depth on -the eastern and western ends, hence the water problem in these properties.

Jan 1, 1921

By Dennis H. Laubscher

INTRODUCTION The selection of mass mining methods is the situation facing not only planners of new operations, but also those involved with cur- rent operations, including the eventual change from open-pit to underground. Increasing ground control problems on many mines, plus a better understanding of dilution and ore loss problems have meant a review of current mining methods and support techniques. Experiments are only successful if conducted in the right mining environment and on the right scale. Mining personnel have been known for their conservatism and will tend to persevere with an established method rather than change; often, hidden costs will obscure the correct economic assessment. An established mining sequence is not necessarily correct in the long term. However, recommendations to change are usually met with opposition because of inconvenience, temporary production problems and the desire for a trouble-free guarantee. In any planning exercise, care must be taken that time and money are not wasted in trying to achieve the unattainable. During the decision-making period, production personnel must be involved, and, if possible, they should visit similar omrations to that proposed. Co-operative production personnel will help ensure success. Descriptions of mining methods are available in technical papers and books, and it is not intended to discuss this aspect, but, rather, the various factors which must be recognised before arriving at a final selection. In another paper presented at this Conference (Heslop and Laubscher, 1981) factors affecting ore recovery and dilution are discussed in greater detail for various cave mining methods. PRELIMINARY CONSIDERATIONS Comprehensive Geological Data. Geological information is available during the exploration stage, but, often, core from exploration drilling is not analysed with the selection of a mining method in mind. Drilling costs are high, therefore the maximum benefits must be derived from this operation. Holes which have not intersected ore may provide data on possible shaft sites, and 35 mm colour slides of core, sound logging and geomechanics classification, will provide a record which can be used with confidence at a later date. Intersections of the various rock types should be kept for future study; for example, is weathering likely to be a problem, bearing in mind that this can be accelerated in the warm, humid atmosphere of an underground mine. The accumulation of data required to select a mining method starts with initial geological work in the target area, whether this be surface mapping or a diamond drill hole. Publications. As technical papers, reports and books are used in the selection of mining methods, an appeal is made to authors to describe the geological environment so that readers can relate to their own conditions. Not enough emphasis is given to the problems experienced and the techniques employed to overcome them. Follow-up papers are seldom written and we should be prepared to discuss our failures. Diagrams are often misleading, as the ideal and not actual situations are depicted. The caved ore/waste interface is not a straight line, and whereas this may not be significant in a diagram of a 200-117 draw height, it certainly is in sub-level caving with draw zones only 1 - 2 m width but up to 20 m high. SUMMARY OF FACTORS AFFECTING THE SELECTION OF UNDERGROUND MASS MINING METHODS (a) Regional rock stresses and mining geometry. (b) The geomechanics rock mass classification of the orebody and surrounding rock mass. (c) Ratio of the surface area of the ore/unpay interface to the contained ore which determines ore losses and dilution. (d) The cavability and fragmentation data of the ore and hangingwall. (e) The mineral distribution in the orebody and its dilution zone.

Jan 1, 1981

By Charles T. Holland

In connection with the problems of bumps in coal mines, much has been written concerning the manner in which roof action and methods of mining enter into the pressure effects observed but little has been written upon the relationship between the physical properties of coal and associated rocks and the cause of bumps. The question of the strength of bituminous coal, of its elasticity, and the energy it can absorb and store has been neglected to a considerable extent in connection with this problem. It is generally agreed that one of the necessary conditions for bumps is a strong coal.' Therefore, since the strength of coal is an important factor, a study of this property should be made. several investigators have conducted laboratory experiments upon the strength of coal, using small cubical or rectangular test pieces. An attempt will not be made to go into all of these investigations, but they are briefly summarized in Table I. Experiments of the U. S. Bureau of Mines and of Lawall and Holland (pp. 27 and 34 of ref. 9), however, indicate that regardless of whether the coal is a soft and weak semihituminous (Pocahontas No 3) or a hard and strong bituminous (Stockton) coal, the maximum ultimate unit stress developed in laboratory tests is higher in small cubes than in larger cubes of the Same coal.

Jan 1, 1942

By Charles T. Holland

In connection with the problems of bumps in coal mines, much has been written concerning the manner in which roof action and methods of mining enter into the pressure effects observed but little has been written upon the relationship between the physical properties of coal and associated rocks and the cause of bumps. The question of the strength of bituminous coal, of its elasticity, and the energy it can absorb and store has been neglected to a considerable extent in connection with this problem. It is generally agreed that one of the necessary conditions for bumps is a strong coal.' Therefore, since the strength of coal is an important factor, a study of this property should be made. several investigators have conducted laboratory experiments upon the strength of coal, using small cubical or rectangular test pieces. An attempt will not be made to go into all of these investigations, but they are briefly summarized in Table I. Experiments of the U. S. Bureau of Mines and of Lawall and Holland (pp. 27 and 34 of ref. 9), however, indicate that regardless of whether the coal is a soft and weak semihituminous (Pocahontas No 3) or a hard and strong bituminous (Stockton) coal, the maximum ultimate unit stress developed in laboratory tests is higher in small cubes than in larger cubes of the Same coal.

Jan 1, 1942

By AIME AIME

A DOCUMENT of progress and of great interest to engineers is the report of the Military Affairs Committee of 'the Engineering Council, which has just been accepted and sent to the secretary of War. It provides .a plan whereby civilian engineers holding commissions in the Reserve Corps may; with their con- sent, be called into service of the army during peace at any time, either with troops in the field or in a consulting capacity on any government engineering work. The Military Affairs Committee finds ample authority in the military bill passed by Congress on June 4, 1920, for this arrangement and also for extending the privilege to military engineer, officer-s of the regular army to engage in civilian work during times of peace. It is hoped that the Secretary of War will adopt the suggestions and put the program outlined into effect. This is a constructive piece of work comparable to the efforts of the military Committee before the war which developed so much in the way of preparedness, particularly in the program of military lectures which, held in the auditorium in the Engineering Societies Building, became so popular that each lecture had

Jan 1, 1920

By Harry W. Brown

This paper presents results of static capillary pressure measprements made both by the restored-state and by the mercury-injection methods, and of dynamic capillary pressure measurements made by the Hassler technique. The results indicate a variation from sample to sample of the factor used to convert capillary pressure obtained by mercury injection to those applicable to a water-gas system. Static capillary pressures measured by the restored-state method were found to be in close agreement with dynamic capillary pressures, indicating that data obtained from static measurements may be utilized with confidenre in the solution of dynamic problems of fluid flow. Experimental data are presented on the use of "J-curves" for the correlation of capillary pressure-saturation relations for a number of cores from a particular geologic formation. It is shown that the correlation was improved in some cases by reqtricting it to rertain lithologic classifications. INTRODUCTION The Meaning and Importance of Capillary Pressure The coexistence of two or more immiscible fluids within the voids of a porous medium, such as reservoir rock, gives rise to capillary forces. Because of the interfacial tension existing at the boundary between two immiscible fluids in a pore space, the interface is curved, and there is a pressure difference across the interface. This pressure difference is termed the capillary pressure. The magnitude of the capillary pressure between two immiscible fluids which together fill a porous medium depends upon several factors: the textural properties of the medium, the wettability of the medium, the interfacial tension between the fluids, the respective saturations of the fluids, and the manner in which these saturations are attained. For a given pair of immiscible fluids in a particular sample of reservoir rock, the capillary pressure is a unique function of the fluid saturation, provided that the saturation of the fluid which wets the rock has previously been decreased unidirectionally from an initially complete saturation. Similarly, for a given pair of fluids at a particular saturation which has been achieved by a

Jan 1, 1951

By Harry W. Brown

This paper presents results of static capillary pressure measprements made both by the restored-state and by the mercury-injection methods, and of dynamic capillary pressure measurements made by the Hassler technique. The results indicate a variation from sample to sample of the factor used to convert capillary pressure obtained by mercury injection to those applicable to a water-gas system. Static capillary pressures measured by the restored-state method were found to be in close agreement with dynamic capillary pressures, indicating that data obtained from static measurements may be utilized with confidenre in the solution of dynamic problems of fluid flow. Experimental data are presented on the use of "J-curves" for the correlation of capillary pressure-saturation relations for a number of cores from a particular geologic formation. It is shown that the correlation was improved in some cases by reqtricting it to rertain lithologic classifications. INTRODUCTION The Meaning and Importance of Capillary Pressure The coexistence of two or more immiscible fluids within the voids of a porous medium, such as reservoir rock, gives rise to capillary forces. Because of the interfacial tension existing at the boundary between two immiscible fluids in a pore space, the interface is curved, and there is a pressure difference across the interface. This pressure difference is termed the capillary pressure. The magnitude of the capillary pressure between two immiscible fluids which together fill a porous medium depends upon several factors: the textural properties of the medium, the wettability of the medium, the interfacial tension between the fluids, the respective saturations of the fluids, and the manner in which these saturations are attained. For a given pair of immiscible fluids in a particular sample of reservoir rock, the capillary pressure is a unique function of the fluid saturation, provided that the saturation of the fluid which wets the rock has previously been decreased unidirectionally from an initially complete saturation. Similarly, for a given pair of fluids at a particular saturation which has been achieved by a

Jan 1, 1951

By G. A. Merkt

THE Isley furnace control, here presented as a novelty in furnace construction, is, in principle, one of the oldest methods of maintaining furnace heat for industrial purposes. Records unearthed in Egyptian tombs and the primitive methods of melting metal practiced by African tribes today indicate that fanning the fire and forcing the furnace by bellows have been an effective means of regulating heat for man's work during thousands of years. Even today, these cruder forms of mechanical draft production are still nn use within the borders of this most highly developed industrial land. Stacks, as we know them, are of com- paratively recent historical age but their attractive simplicity and seeming effectiveness have made them exceedingly popular. And so we find one of the most important types of furnace the world has even known, the open-hearth furnace, duly and more or less properly equipped with a chimney. The regenerative, or reversing, type of furnace, how-ever, required another mechanism between its hearth and the stack to provide a means for alternately con-necting one side and the other of its system of regen-erative chambers and flues to the stack and to a source of fuel and air supply respectively. Various types of reversing valves were developed, some of which are re-markably well designed for maximum efficiency and ease of installation as well as operation. However, this combination has a number of inherent faults which are so difficult to correct as to make efforts in the direction of improving over-all efficiency almost futile. These inherent difficulties are as follows: (1) The necessarily high temperature at which the gases must be delivered to the stack in order to make it operative. (2) The great temperature difference incidental to the reversal of flue gas and air and consequently the large variation in preheated air and fuel delivered to the furnace dur-ing the cycle. (3) The leakages and resistances created by the reversing apparatus and the complicated flues necessary. (4) The inadequate range of control af-forded by the natural draft system, especially under adverse atmospheric conditions.

Jan 12, 1927

Coal Division Industrial Minerals Division Minerals Beneficiation Division Mining, Geology and Geophysics Division Established as a Society February 26, 1957 OFFICERS AND COMMITTEES J W Woomer, President A B Cummins, President-elect S D Michaelson, Past President C E Lawall, Eastern Regional Vice-President D W Scott, Central Regional Vice-President 3 D Forrester, Western Regional Vice-President R B Ladoo, Treasurer John Cameron Fox, Secretary

Jan 1, 1959

By S. J. Rothman, J. J. Hines, D. Rokop, R. Bastar

Self-diffusion has been measured along each principal axis of mosaic-structured and relatively perfect a uvaniuln single crystals. The anisotropy reported before,' D[loo] = D[001] » D[010 , has been confirmed. and is shown to represent volume diffusion. Diffusion along the dislocations in the imperfect crystals increases the measured value of D significantly without changingr either the shapes of the penetvation plots or the anisotropy. SINCE a uranium is orthorhombic, the diffusion coefficients along the principal crystallographic axes need not be equal. A previous measurement of self-diffusion in three mosaic-structured a uranium single crystals1 showed that Dil00| =D[001 >>D[010 This result was deduced from penetration plots similar to those in Fig. 1. That is, the plots for diffusion along [loo] and [001] were the straight lines expected from the solution of the diffusion equation for the boundary and initial conditions of the experiment, while the plot for diffusion along [010] was curved so that the part near X = 0 had a much steeper slope than the straight lines did. The observed anisotropy could have been due either to volume diffusion or to diffusion along the very large number of dislocations in such crystals, according to the model proposed by aart.' The authors of Ref. 1 argued that the latter possibility was unlikely, but did not exclude it. To settle the question, a simultaneous measurement of self-diffusion in mosaic-structured and mosaic-free crystals was carried out. This paper reports the results, as well as a measurement of the temperature dependence of self-diffusion in a uranium. EXPERIMENTAL The single crystals of a uranium used in this experiment are listed in Table I, together with other experimental details. '(Mosaic structured" here means crystals grown by solid-state phase change.3 The Laue spots from such crystals spread over about 6 deg of arc, which indicates that the density of dislocations is very large. "Perfect" crystals are ones grown by Fisher's grain-coarsening tehnique; the Laue spots from these are quite sharp,4 which shows that the dislocation density in these crystals is much lower. All of the crystals were made from high-purity uranium; a typical analysis is given in Ref. 1. The actual diffusion directions were within a few degrees of the nominal. The thin layer-sectioning method was used. The experimental techniques were similar to those described in Ref. 1, except the sectioning. Crystals Za, 2b, 2c, 4a, 4b, and 4c were sectioned on a lathe. Crystals 3a, 3b, and 3c were sectioned by grinding on glass plates, with 1 p diamond powder in butyl alcohol as the abrasive. The use of glass plates eliminated the crowning noted in Ref. 1, and the use of butyl alcohol as a lubricant simplified the chemical processing of the sections. Material from the sides of these three crystals was removed by spark machining before sectioning. The sectioning of crystals 4a and 4c was botched. A small cylinder of metal was extruded from the center of crystal 4a while turning off material from the side of the sample. Crystal 4c was misaligned by 2.1 x 10"3 cm because the dial gage jammed during the alignment. Notwithstanding these errors, useful data were still obtained from these crystals. The points

Jan 1, 1967

By J. C. Bayles

Jan 1, 1886