Search Documents

By John Chipman, Peter J. Koros

The distribution of copper between liquid silver and liquid iron, Fe-C, and Fe-C-Si alloys was studied at 1600°C. From the data and the activity of copper in silver obtained from the phase diagrams, the activity coefficients of copper in iron up to 3 atomic pct are log y, = 0.90 — 2.4 N, and y": = 8.0. The effect of carbon up to saturation is expressed as log y = 1.8 Ni. The effect of silicon up to 11 atomic pct is insignificant. SLOWLY rising copper content of steel being produced is focusing attention on the lack of information on the behavior of copper in liquid steel. Chou' measured the activity coefficient of copper in liquid iron through its distribution between liquid silver and iron. He obtained a value of 9.12 at infinite dilution. Chipman' calculated the activity coefficient of copper in liquid iron at 1600°C from the phase diagram and obtained a value of 12. Ameiln and Pfeiffer- investigated the possibility of removing copper from liquid steel through the use of lead, silver, and bismuth as solvents. They also calculated that the activity coefficient of copper in liquid iron would be increased five or sixfold by addition of 4 pct C. Langenberg and Lindsay' are investigating the effectiveness of lead and sodium sulfide in removing copper from liquid iron. The experimental method was similar to that used by Chou' and Chipman and Floridis." Silver, copper, and iron were melted together, the copper distributing itself between the two layers so that at equilibrium a,.,, (in Ag) - a,.,, (inFe) and N,.,, (in Ag) yc,, (inFe) (in Ag). [21 N,.,, (inFe) Thus, from the concentration of copper in each layer and the activity coefficient of copper in liquid silver, the activity coefficient of copper in liquid iron can be calculated. The effect of an alloying element such as carbon on the activity coefficient of copper can also be determined from its effect on the distribution, provided the new element is essentially insoluble in silver. The one serious limitation of this method is the increasing mutual solubility of silver and iron in the presence of a third component. The mutual solubilities of pure iron and silver are negligible, but increase with increasing copper concentration beyond the range investigated. Ag-Cu System—The activity coefficient of copper in silver at 1600°C had to be estimated, since direct experimental data are not available. Kawakami" measured the heat of mixing of Ag-Cu alloys at 1200°C by a calorimetric technique. Scheil' calculated the heat of mixing in this system by use of the phase diagram, assuming that the solution is random and that the heat of mixing is independent of temperature. The terminal solid solution may be assumed to obey Raoult's law within the requirements

Jan 1, 1957

By H. R. Cooper

Beginning from the point of view that process control of ore flotation can be approached by on-line analysis of processing behavior, an equation was developed which has characteristics useful for a multi-variable feedback loop. The application of this equation to optimizing control with a data acquisition system will be discussed in Part 11. OBJECTIVE OF CONTROL The purpose of developing a feedback method for concentrator control is to provide a means for determining ore processing behavior in order that data describing the ore can be used to make appropriate changes in control conditions while the ore continues to flow through the flotation circuit. In absence of simple linear relationships between pairs of variables in the flotation process, attention is directed to the need for a generalized relationship which possibly would incorporate all pertinent variables. It would be possible to apply such an equation to the control of variables in a concentrator in real time according to operational requirements as ore gradually changes in quality and processing behavior. To meet this objective, it is necessary to define relationships describing flotation performance in terms of performance variables capable of being measured on-line, either with on-line instruments and analyzers or with manual methods lending themselves to quick determination of meaningful information. Relationships derived to meet this objective form a model for the flotation process. The evaluation of flotation parameters of the ore and the execution of control on the basis of the derived information while the ore is continuing through the process would constitute a feedback control system. Data for the following control and performance variables can be made available: 1) ore feed rate, 2) collector addition rate, 3) lime addition rate, 4) pulp density, 5) assay or multiple assays in feed, tails, or concentrate sufficient for material balancing, 6) particle size distribution in flotation feed, 7) froth height, and 8) frother addition rate. Other process variables, such as flotation air input and mechanical agitation intensity, are usually not considered as control variables and were not taken into account in this analysis. Other data, such as that describing the ore, would be useful for concentrator process control. However, information of this type (such as ore hardness, grain size of the mineral, chemical species of the mineral, and ore surface properties) being not presently measurable in the on-line sense, has the effect of causing disturbances in the system which can be detected only indirectly. The process control system being sought must recognize disturbances by their effect on measured performance followed by determining control changes to compensate for them in meeting the objectives of improved performance (perhaps higher throughput, maximum return, etc.). A suitable model for the process having capability of recognizing the effects of ore disturbances should provide the means for introducing proper compensation through control changes. This would be done by processing on-line data with the model to calculate coefficients reflecting ore characteristics. This procedure can only be applied in a typical flotation system when on-line data can be processed at faster rates than the usual rate at which the ore in flotation feed takes on significantly different characteristics. For example, material balance data can be accumulated in approximately 5-min intervals using on-line X-ray fluorescence analysis. The flotation system time constant might be 15 min including grinding. Ore changes having time constants longer than 1 hr could be accommodated using on-line feedback control by this procedure. FORM OF A FLOTATION MODEL A suitable form for mathematical expression of the flotation process is an equation involving rates, when each of the components entering into the separation can be treated independently by a rate equation. A first-order, kinetic rate equation can be written on

Jan 1, 1967

By C. Feng, C. Elbaum

Knoop hardness measurements were carried out on large grains of iodide titanium containing different amounts of oxygen. For each oxygen content the hardness is recorded ainingas a function of the crystal orientation and of the angle 4 between the indenter diagonal and the projection of the C (hexad) axis in the surface. The results can be expressed by the following relation; hardness = n-k cos 2ø, where n and k are constants for a given oxygen content and crystal surface orientation. A NISOTROPY of hardness is a well-known phe-nomenon and has been reported for many metals.1-3 At the present time, however, such information is not available in the literature for titanium. Consequently, a systematic study of the simultaneous effects of oxygen content and crystallographic orientation on the hardness of titanium was undertaken in this laboratory. Evaluations of oxygen content in titanium are frequently carried out through hardness tests. Although such procedures may be justified in small grain specimens, the results of the present investigation indicate that the anisotropy of hardness should be taken into account in the case of coarsegrained specimens as well as in the case of pronounced preferred orientation. Materials and Experimental Procedures Iodide titanium, 99.99 pet pure and containing of the order of 0.002 wt pet O, was used throughout this investigation. The metal was arc melted in an argon atmosphere and cold rolled into strips 1/16 in. thick. These strips were subsequently recrystal-lized and strain annealed in vacuum (10" mm Hg or better) at 850°C in order to produce crystals varying in diameter from 10 to 25 mm. Oxygen was introduced into selected large crystals by heating at 700°C in an atmosphere of pure oxygen under an observed pressure of approximately 50 mm Hg. Each sample was subsequently annealed in vacuum at 850°C for 100 hr, in order to homogenize the oxygen content throughout the specimen. It was found that longer annealing was not necessary, for no change of surface hardness in a given direction was detected after prolonged annealing. The oxygen content was determined by the difference in weight of the specimens before and after the oxidation-annealing cycle. The accuracy of oxygen determination is within ±0.1 mg in samples weighing 0.5 to 1 g. A vacuum fusion analysis of oxygen was performed on several samples and gave results in good agreement with the ones obtained by the weight change. It should be emphasized that expected weight losses through evaporation of the metal in vacuum at 850°C' are many orders of magnitude lower than the precision of these measurements. Following the annealing treatment, both oxidized and unoxidized crystals were carefully polished. All detectable traces of surface cold working were removed by repeated polishing and etching. Laue back reflection X-ray patterns were taken for each crystal for the purpose of determining the orientation and ascertaining the absence of substructures detectable by this method. Hardness measurements, using a 1 kg load, were subsequently carried out on a Tukon hardness tester equipped with a Knoop indenter. The Knoop indenter was used throughout this work because indentations obtained by means of a Vickers indenter are considerably distorted due to the anisotropy of the elastic constants in titanium. Such distortions are much less pronounced in the case of Knoop indentations, although for some orientations a cer-

Jan 1, 1959

Jan 1, 1879

By I. H. Van Horn

IN the development of the incandescent electric lamp one aim of the investigators has been to establish the fundamentals of lamp design, so that the performance of any new lamp may be accurately predicted. The study of the temperature relations in lamps has done much toward establishing these fundamentals. Fig. 1 gives the typical FIG. 1.-ARRANGEMENT OF PARTS IN MAZDA B AND MAZDA C LAMPS. arrangement of the lamp parts in both the Mazda B (vacuum) and Mazda C (gas-filled) lamps. The outstanding differences are the filament form and the bulb shape. The ideal lamp is one in which the filament operates at a uniform temperature throughout its length. In practice, it is necessary to disturb this uniformity by the introduction of supports and terminals. The amount of cooling at the supports and terminals affects the over-all efficiency of the filament as a light producer. The life of the lamp is ordinarily proportional to the maximum and not to the average filament temperature. The Holborn-Kurlbaum type of optical pyrometer has

Jan 9, 1919

By René de Batz

From 1754 to the end of 1895 the production of gold in Russia had been approximately as follows: Kilogrammes. Russia proper (Finland and the Caucasus),. .. 890 The Ural Region,........505,386 Western Siberia,........116,937 Eastern Siberia,........1,218,372 Total,.........1,841,085 of the value of more than $1,200,000,000.

Jan 1, 1899

By W. A. Burns

Vertical flow is an important mechanism in many petroleum reservoirs. Yet no adequate method has heretofore been proposed for determining the in-situ vertical permeability in a reasonable length of time. Core measurements of vertical permeability do not necessarily represent effective in-situ values. Cores may be representative of only localized pockets of high or low permeability, and total reliance on cores might cause one to overlook the presence of vertical fractures altogether. Conventional single-well tests, interference tests, and pulse tests commonly are used to determine horizontal transmissibility, khh/u, but generally are not designed to measure vertical trans-missibility or other groups containing vertical permeability, ku. A new well test described here provides a measure of in-situ vertical permeability as well as the previously measurable horizontal permeability. This "vertical test" determines the vertical diffusivity, kv/gcu, and horizontal transmissibility, khd1/u (where dl is the length of injection or production perforations). The test is basically a short-term interference or pulse test normally lasting less than a day. Conventional down-hole equipment is used between two isolated sets of perforations in the same well, as shown in Fig. 1. A "layer-cake" description of a reservoir can be obtained by running two or more vertical tests in the same well, each over different vertical intervals. Each test can be analyzed for the effective vertical and horizontal properties of the interval tested. In addition, a vertical well test can determine the effective- ness of a shale barrier or tight zone by testing across it. Field use to date of vertical testing has confirmed its utility in reservoir description. Mathematical Basis Interpretation of vertical tests for ku and kh is based on comparison of measured pressure response with computer-generated response. Pressure behavior during a vertical test in a homogeneous, anisotropic, infinite-acting reservoir (infinite in radial extent and bounded in both directions vertically) is given by the diffusion equation for slightly compressible fluids with negligible gravity effects.l A schematic diagram of the problem is presented in Fig. 2, and an analytic solution, based on the image

Jan 1, 1970

By C. R. Kuzell

IN COMPARISON with recent years 1932 has yielded much less tangible evidence of progress in copper reduction and refining. The industry has been extremely quiet, especially in the United States. Design and construction has been throttled by lack of new capital expenditures. The excess producing capacity of the whole industry and the extremely gloomy outlook for the future have made it unwise to tie up more capital except under special conditions. The plants built during the previous year have, however, been placed in operation. Older plants have been abandoned, temporarily shut down, placed on part time operating basis, or continue to operate at a low percentage of normal capacity. In the United States the Phelps Dodge Corporation at Douglas, Ariz., has completed the remodeling of the former Calumet & Arizona smelter. A new roaster and Cottrell plant chimney was completed this year. Though operations have been limited the new equipment has been found to justify all expectations. The reverberatory plant addition consists of two furnaces 26 by 107 ft. inside dimensions, with a high arch, and modern steel binding of excellent design. Natural gas fuel gives good results. One of these furnaces will treat 1000 tons of solid charge per day with a fuel consumption of approximately 3,000,000 B.t.u. per ton. The larger converters have not only yielded the expected lower costs, but have simplified operations in the converter department. One of the noticeable results is the greater cleanliness in the environment and the absence

Jan 1, 1933

By H. E. Lee, D. Ingvoldstad

AT Bunker Hill the original charge storage and preparation system was installed in 1917 to accommodate lead-silver gravity mill products. Only minor tonnages of wet fines such as vanner and flotation concentrates were received. Charge flux and diluent requirements were provided by an ample supply of siderite middlings and coarse lime-rock. While oversize material was crushed through %-in., the use of roll crushers in series resulted in a more or less granular, free-running charge of adequate porosity. Under such conditions, receipts could be proportioned directly from receiving bins, and suitable blending was obtained by passing the resultant layered composite through a small Stedman disintegrator. This elementary system served well for production and smelting of an extremely lead-rich sinter, in the low column blast furnace. Here sinter physical quality is less critical, and appreciable quantities of raw flux and oxidized ore may be charged directly to the blast furnace without seriously impairing furnace capacity. Prior to 1938 the relative proportions of zinc receipts were low and extraneous flux requirements at a minimum. However, subsequent war-inflated zinc demands brought marked increase in fine concentrate and slimy zinc leach residue receipts and an abrupt introduction to smelting a more refractory zinciferous charge. The higher temperature demands of the more refractory zinciferous charge required a higher smelting column and the higher column, in turn, rendered the blast furnace less receptive to improperly prepared feed. Inadequate presinter processing facilities prevented the production of acceptable sinter, and blast furnace production declined to 50 pct of former capacity. In view of a prevailing contention among lead metallurgists as to the deleterious action of high zinc slag on blast furnace capacity, it was natural to overstress this factor and to concentrate on possible changes in furnace design. Another interpretation was that primary correction should be sought through expanded sintering facilities. This divergence of opinion, together with the extreme material shortages of the 1940's, delayed corrective

Jan 1, 1957

THE members arrived at Ticonderoga, N. Y., at noon, Tuesday, October 15th, and were received by Mr. Cyrus Butler, Chairman of the Local Committee of Arrangements. During the afternoon the works of the American Graphite Company and the Horicon Iron Company were visited under the guidance of Mr. Butler, President of both companies, and of Mr. William Hooper, Superintendent. An excursion was then made, in carriages, to old Fort Ticonderoga, on Lake Champlain, after which the party were driven to the Rogers Rock Hotel, on Lake George. The first session of the Institute was held in the parlor of time hotel on Tuesday evening. Mr. Eckley B. Coxe, President of the Institute, opened the proceedings with the following address: I shall ask your attention, this evening, to a few reflections upon the subject of mining engineering as a profession in the United States, its past, its present, and its future, and its duties and oppor¬tunities with reference to the proper development of our great min¬eral resources. Thirty years ago, there were scarcely any mining engineers in this country, and but few in England, and there were no institutions where young men could be educated for the profession in the Eng¬lish language. France and Germany have been able for about a century to boast of mining schools of a high character, that number among their graduates such men as Humboldt, Weisbach, Rittinger, Combes, and Gruner. Of the few we then had worthy of the name of "mining engi¬neer," some had studied in the continental academies, and others were graduates in the school of practical experience, and had learned their profession in mines and smelting-works. Their work con¬sisted principally in making surveys and maps of mines and mining properties, geological reports, and analyses of ores ; but the mining engineer whom we often meet with now, who has studied chemistry, physics, mineralogy, geology, mechanics, and drawing; who is more or less familiar with machinery and its construction, and with the practical management of mines or smelting-works, and who is an expert in some one branch of his profession, would have been very difficult if not impossible to find in the United States. The induce¬ments held out to ambitious and talented young men to enter the

Jan 1, 1879

By Clyde E. Williams

IN planning a postwar program for manufactured products, it is essential that the bases for the plans be wisely chosen. First we must make certain assumptions as to the war's ending. Let us assume: (1) complete victory by the United Nations, (2) peace terms that will ensure the direction of the economy of all nations of the world toward peaceful pursuits, and (3) an early ending of the war, that is, before the nations of the world, excluding the enemy, are near the point of physical and spiritual exhaustion. Thus, our manufacturing plants and transportation facilities will still be in good shape. The plants and transportation facilities, as well as the cities of a large part of Europe, however, will be badly crippled. The rich mineral and other raw material resources of the world, little of which was under control. of the Axis powers before the war or will be after the war, will not be used up. Control of these raw materials, or at least an important part of them, will remain in the hands of the strong peaceful nations.

Jan 1, 1943

By Johannes Moeljono, Werner Wenzel, Heinrich Wilhelm Gudenhau

As an important mechanism for increasing production of the suction-draft-sinter process, it has been shown that gas permeability through the sinter layer plays an important role. Methods to increase production rates have been indicated and suggestions for carrying out the process have been made to improve the rate of production, reduce the fuel consumption, and at the same time obtain a uniform sinter. Laboratory experiments were conducted at the Institute for Ferrous Metallurgy of the Technical University at Aachen to illustrate these methods. Methods of Increasing Gas Penetration Through Sinter Layers The following are of fundamental importance in determining the process cycle during the sintering of iron ores: 1) Generation of maximum temperature, since its form and range determine sinter quality. 2) Propagation velocity of the temperature maximum which controls the attainable output. 3) The convective heat transfer which influences the velocity of travel of the temperature maximum.

Jan 1, 1974

By J. E. Campbell, A. W. Wesner, M. Pobereskin

This paper summarizes the results of an investigation sponsored by The Coates Steel Products Company. The objective was to determine the relative effects of certain chemical and physical properties on the wear resistance of grinding balls when grinding cement. In making this study, a number of types of balls were used in both dry and wet grinding in commercial ball mills. The radioactive-tracer technique was used in separating the test balls from the rest of the mill charge and in sorting the different types of halls that were all tested at the same time for each of the grinding operations. PROCESSING OF GRINDING BALLS In order to determine whether the properties of grinding balls, namely, composition, microstructure and hardness, can be related to the rate of wear, the halls used in this study were selected to represent various combinations of these properties. It was recognized that the mechanism of wear was not the same in the wet mill as in the dry mill. Therefore, the types of balls tested in each of the two environments were not necessarily the same. However, all of the types of balls evaluated in the dry mill were tested simultaneously for one time period, while those evaluated in the wet mill were tested simultaneously for three different time periods. All of the test balls were separated from the charge when the mill was dumped. All of the balls were of 0.940-inch diameter when charged, and all but the regular production balls were finish ground to this size to eliminate the decarburized surface layers. The steels and processing methods used, as well as the micro-structures and hardness levels of the balls, are described as follows: Regular production forged SAE 1095 steel balls were used in both the wet and dry mills. They were forged to a nominal diameter of 0.940 inch and quenched in oil from the forging temperature. Each retained a partially decarburized surface layer from the forging bar stock; the maximum depth of this layer was about 0.030 inch and the decarburization was negligible where the ball was sheared from the bar. The hardness at the surface was 40 to 46 Rock-well C in the partially decarburized area and 57 to 62 Rockwell C in the areas not decarburized. The hardened zone extended to a depth of about one-third of the radius. Below the decarburized layer, the hardened zone consisted primarily of hard as-quenched martensite with varying amounts of retained austenite. This structure changed to fine pearlite at a depth of about one-third of the radius. In order to eliminate the effect of the decarburized layer, a set of production balls of SAE 1095 steel was forged to about a 1-inch diameter, quenched in oil from the forging temperature, and ground on ball-bearing grinding equipment to a 0.940-inch diameter to remove the decarburized layer. The balls' hardened zones were similar to those in the previous set. The hardness of the finished surfaces was 52 to 60 Rockwell C. A slight amount of decarburization apparently remained after the removal of about 0.030 inch from the surface. Balls of this type were tested in the dry mill only. Another set of forged SAE 1095 steel balls of 1-inch diameter was heated to 1500 F and quenched

Jan 1, 1961

By Milnor Roberts

WAR struck the mineral industry of Washington with cross currents that produced a peculiar result. The State's production of coal, industrial minerals, and metals for 1941, valued at $28,507,282, was increased in 1942 under war pressure to approximately $35.000,000. Meanwhile a tremendous demand had arisen for men to construct airfields and many other large projects for the Army and Navy in Washington and Alaska, and Government plants for the mineral industry costing $140,000,000 or more, as well as a call for employees in the U. S. Navy Yard at Bremerton, the sixty shipyards, the four Boeing airplane factories with many auxiliary shops, and hundreds of other plants turning out war materials. In spite of an influx of nearly 300,000 people, causing an increase of 17.1 percent in the population since 1940, according to the Census Bureau, the State clearly is still engaged in an unusual amount of war production in proportion to its population. A large proportion of the workers have been drawn from the mineral industry to the war plants, whether through motives of patriotism, high wages, or, in the Boeing plants at least, the glamour of the operation

Jan 1, 1944

By William Paxton Hewitt

In the Santa Eulalia mining district, Chihuahua, Mexico, the main mineral zone occurs in a gently warped dome with simple associated structures and contains orebodies distributed through a vertical range of over 900 m. The stratigraphy of 1945 m of geologic column is described and an abrupt shrinkage is documented in the volume of limestones immediately associated with large orebodies. Termed collapse, this shrinkage occurred during the course of mineralization. Contacts of limestone with igneous sills, and 366 m of fossiliferous limestone beds, particularly the main fossil bed, have been important localizers of ore-bodies. Up-dip gravitational controls may have been important. Fractures have exerted only local controls and over short distances. Thrust zones have displaced diabase sills and in turn have been intruded by upper members of a group of rhyolite porphyry sills. Mineralizers were related to the rhyolite porphyry, and ore has been introduced to the limestone where certain sills lie between the displaced segments of diabase and have been cut by north-south fissures. Speculations are raised that fields of unreleased strain may have influenced orebody locations; the district's zoning pattern may be a reflection of the filtering effects of large volumes of limestone; and that metal-rich brines mobilized by or incorporated within the invading porphyry might be the source of the mineralizers. PRODUCTION AND LOCATION The Santa Eulalia district has a production record approaching or exceeding 35 million tons of silver-lead-zinc ore from replacement bodies in limestone. In operation since the first years of the 17001s, production has been confined to two intensely mineralized areas separated by 2 km of barren limestone, the West Camp and the East Camp. Probably 50% has been mined since 1908, with over 90% from the West Camp. The West Camp, exploited through a vertical depth of 1945 m and now approaching exhaustion, is the subject of this paper. The district lies in the northern part of the Santa Eulalia Mountains in central Chihuahua in northern Mexico, 400 km south of El Paso, Texas, and 22 km southeast of Chihuahua City. Dominating the northern part of the range is the Cerro de Santa Eulalia, a broad rolling upland which contains the district's West and East Camps. The West Camp, on the west side of the range, centers around the village of Santo Domingo, which is 2 km northeast of the Real de Santa Eulalia (Fig. 1). REGIONAL GEOLOGY Thick-bedded middle Cretaceous limestones, probably Aurora, form the great bulk of the Cerro de Santa Eulalia. These beds, warped into a gentle dome, are severed on the west by a faultline scarp and truncated on the north by the Dolores Pass, a wind gap that

Jan 1, 1969

By W. J. Verner, J. R. Lucas

Billions of tons of bulk solid materials are processed through our industrial plants each year, and the tonnage is steadily rising. It has been estimated that for every dollar spent in industry as a whole, approxinlately 30 cents is consumed in the handling of bulk solid materials. It is in this category that tremendous savings are possible through the use of improved techniques. Since World War 11, the mining, steel, chemical, and grain industries, among others have made use of increased materials-handling automation in order to gain some of these savings. However, in a chain of automatic operations, every link must be completely reliable, for if there is a single failure, the whole system immediately becomes ineffective. Only too often the weak link in the chain proves to be the flow of bulk solids from bins. To contribute to the fundamental knowledge in this area, a research study has been continuing at The Ohio State University. The principal objective of the investigation has been to study the internal stresses existing in confined bulk solids. LITERATURE SURVEY Literature studies have revealed that many outstanding people have made contributions to the field of bulk solids. For instance, C. F. Jenkin,1 suggested: a. The pressure on a bin wall is not directly proportional to the depth beneath the surface of material in the bin. b. The vertical pressure distribution on the base of a bin is not actually uniform but is a variable. c. Arches form in bins as a result of very small deformations of the material in the bin. This deformation causes a series of gaps to appear, and consequently causes the disappearance of diagonal forces that cannot act across these gaps. The removal of the diagonal forces causes horizontal forces to be introduced which seem to be the chief cause of arching. 11. A. Janssen,4 in 1895 in connection with his experiments on bins, derived a differential equation to describe both the lateral and vertical pressure in bins with vertical sides. This represents a significant contribution to bulk solid theory, and thus its solution is reproduced as follows: L = KV = RW/U' [l-e -U'KY/R] I where L is the lateral pressure of the bulk solid in psf., V is the vertical pressure of the bulk solid in psf., K is the ratio of the lateral pressure to the vertical pressure at any point, R is the hydraulic radius of the bin in feet, W is the density of the bulk solid in lbs. per cubic feet, U' is the coefficient of friction between the stored material and the bin wall, and Y is the head of material above the point in question in feet. In 1903, Jamieson,6 in an elaborate series of experiments on full sized bins measured vertical and lateral pressures by hydraulic diaphragms. He determined many values for mediums of corn, wheat, peas, and flaxseed. In 1951, Caughey, Tooles, and scheer3 measured both lateral and vertical pressure in deep bins by using strain guages on steel bands. Values were calculated for cement, gravel, sand, soy beans, shelled corn

Jan 1, 1961

By J. D. Rice, S. C. Pitzer, C. E. Thomas

Interpretation of pressure build-up data obtained in the conventional manner has often been difficult because of the deviation from theoretical behavior. Major causes of this deviation have been attributed to damage and afterflow, and to fluid redistribution in the wellbore which, in extreme cases, can result in a pressure hump in the early portion of the build-up curve. Theoretical investigations show that bottom-hole pressure is definitely influenced by phase redistribution in the tubing column during surface shut-in tests, and that the magnitude of the effect is sensitive to the producing gas-oil ratio and stabilized rate of flow in the well. For field experiments a wire-line tubing packer, which can be run in the tubing against a stabilized flow rate, was developed for bottom-hole shut-in tests. By use of this bottom-hole .shut-in method, pressure humps previously observed in surface shut-in tests were completely eliminated and the effects of afterflow minimized. Analog and digital computer studies have been made to obtain theoretical curves for comparison with field curves, and remarkable agreement between the results of bottom-hole shut-in tests and theoretical curves has been obtained. INTRODUCTION Pressure build-up data from shut-in wells have been used by the petroleum industry to determine the permeability of the formation, to estimate wellbore damage, to evaluate the static reservoir pressure and to speculate reservoir volume. Calculation of these factors is based on methods of analysis developed for theoretical systems whose build-up curves have a charac- teristic shape when the wells are shut-in at the sand faCe.1,2,3,5,8,10 However, field curves obtained by conventional surface shut-in methods do not always exhibit this characteristic. Such factors as stratification, rock heterogeneities and irregular reservoir geometry can cause the character of a build-up curve to deviate from that predicted by theory for a simple system. In addition, all field build-up data are affected by the methods utilized in obtaining the measurements. Conventional surface shut-in techniques allow two effects to occur which contribute directly to the manner in which pressure builds up at the sand face. The first, afterflow, has been recognized for some time and methods are available for estimating the magnitude of its effect and for correcting its influence.' The second, phase segregation in the tubing column after shut-in, has been reported only recently and appears to exert a considerable influence on the character of field build-up curves.!' In extreme cases, phase segregation can produce "pressure humps" in the early portion of the build-up curve. Such curves have been considered anomalous and have defied analysis. It is the purpose of this paper to discuss the effect of phase segregation in the tubing string during build-up and to present a bottom-hole shut-in technique for obtaining field build-up data which minimizes the influence of afterflow and eliminates phase segregation effects. It will be shown that reliable reservoir information can be calculated from build-up measurements obtained using this method, even though conventional surface shut-in tests on the same wells yield anomalous data. DISCUSSION OF PHASE REDISTRIBUTION EFFECTS Some of the effects of phase redistribution on pressure build-up curves have been described previously by Matthews and Stegemeier" who have presented evidence that phase segregation is responsible for the pres-

By D. G. Westlake

Levine has concluded that prismatic slip in titanium is controlled by two distinct thermally activated processes in the temperature ranges O° to 220°K and 220" to 300°K. We feel that his evidence is not convincing. He has drawn a curve through the plot of activation volume u* vs temperature T with a break at 22WK, Fig. 2. We believe that considering the possible experimental error apd the fact that there are only four points between 4° and 196°K, one could be justified to represent these points by the smooth curve we show as a solid line in Fig. 12. Levine believes that (8rf/aT)+ is discontinuous at 220°K, but he hints that he recognizes the possible doubt. We doubt seriously that the results shown in Fig. 1 indicate a discontinuity at 220°K. Certainly if he were justified in drawing a straight line through only four points on Fig. 2, we are even more justified in drawing straight lines through the seven points between 77" and 297°K on Figs. 1 and 3, because a straight line touches all seven of his circles. If his measurements of t were so precise that his decision to draw two curves in Fig. 3 is valid, then the experimental technique is deserving of further mention. We have drawn a smooth curve through the results in Fig. 3 and used this and the curve in Fig. 12 to obtain the values of shown in Fig. 13. Finding continuous is a contradiction of Fig. 4, which deserves comment itself. Levine obtained the solid circles in Fig. 4 using Fig. 2 and a smooth curve through the points shown in Fig. 3. We have replotted these solid circles in Fig. 14. We submit that there is no basis for his two straight lines (dashed in Fig. 14), and therefore have superimposed the curve that we believe is indicated. Certainly, there is reasonable doubt that a discontinuity in dH/dT exists at 220°K, even when one accepts Fig, 2. Furthermore, if one draws the straight lines indicated by least-squares treatments of the results presented as open circles in Fig. 4, their intersection is at about 196°K, not at 220°K as shown. Thus the alleged agreement between Figs. 3 and 4 with respect to "break" temperatures is not apparent. In Fig. 9, Levine has drawn a straight line very much different from the one indicated by a least-squares treatment. Obviously, he has done this because he recognized that H = 0 when T = 0. He is consistent in drawing the low-temperature curves in

Jan 1, 1968

By T. R. A. Davey

The fundamental principles by which bismuth may be removed from lead by pyrometallurgical processes are enumerated. Qualitative discussion of the phase diagrams concerned is followed by presentation of quantitative diagrams. Brief mention is made of the practical aspects. Data presented show how chemical lead (<0.005 pct Bi) may be produced by the Jollivet, Dittmer, and Kroll-Betterton processes. BISMUTH is an element whose properties are very similar to those of lead, and its minerals are associated to a greater or lesser extent with nearly all the major lead ore deposits of the world. In consequence, the lead produced contains bismuth unless a special debismuthizing process is practiced. There does not appear to be any published comprehensive review of the effect of bismuth as an impurity on the properties of lead, and there is some uncertainty as to the beneficial or detrimental effects of small amounts of bismuth in lead used for particular applications. Standard specifications of most countries stipulate a maximum bismuth content of 0.005 pct for chemical lead. With one exception, this specification is met only by lead producers whose ores are relatively bismuth-free, or whose refineries are electrolytic. In lead for certain applications a higher bismuth content is preferred by some fabricators.&apos; In contrast to the refining for silver, copper, and antimony, the refining for bismuth does not usually result in a large overalil economic gain from the sale of byproduct. Thus, debismuthizing is customarily practiced only if market conditions demand a lead with a bismuth content lower than that produced by classical refining; i.e., softening, desilverizing, and zinc refining. Until this century, debismuthizing was carried out only a:; an incidental result of desilverizing, as later described. This century has seen the development of the Betts electrolytic process—the only successful one of many electrolytic processes proposed and patented —and a number of precipitation processes based on the pioneering work of Kroll,&apos; although only one of these, the Kroll-Better ton process,&apos; is in wide commercial use today. It is proposed in this paper to deal only with the pyrometallurgical processes, excluding those based on aqueous electrolysis. Historical Background Prior to 1833 silver (and incidentally bismuth) could not be removed from lead. To recover silver from rich bullion, the only course available to lead refineries was to cupel the bullion, forming a slag of litharge. The first slag tappings or skimmings, on reduction, yielded soft lead of very low silver and bismuth contents. Intermediate skimmings yielded a lead of somewhat higher silver and bismuth contents, which could if desired be recupelled. The last skimmings yielded a litharge very high in bismuth, which could by successive oxidation and reduction cycles be separated into high purity bismuth, and lead returns. This oxidation reduction process, with modern operating techniques, can still be used today to produce a portion of a lead refinery&apos;s output of very low bismuth content, as discussed later. In 1833 Pattinsone discovered that lead bullion could be purified of silver and bismuth by fractional crystallization, the primary lead crystals formed by partial freezing being purer than the melt. Repeated processing in pans produced a lead containing as little as 0.02 pct Bi. The simple explanation of this

Jan 1, 1957

By F. A. Forward, A. H. Ross, J. Halpern

Application of the carbonate leaching process to carno-tite ores has often been limited by the difficulty of obtaining simultaneous high recoveries of uranium and vanadium. The chemical aspects of this problem are discussed and the effect of prior roasting procedures on this discovery is described. IN treating carnotite ores by carbonate leaching it is often necessary to subject the ore to a prior roast. Among the advantages that may result from roasting are: 1) improvement in settling and filtering characteristics of the ore; 2) destruction of carbonaceous impurities that would otherwise contaminate the leach solution and consume carbonate reagent; and 3) substantial increase in extraction of vanadium, which is usually low when the un-roasted ore is leached. Recovery of vanadium may be an important factor in processing carnotite ores, and the fact that vanadium is usually recovered in good yield by acid leaching has often been an economic advantage over results obtained with carbonate leaching. It has been found that response of an ore to carbonate leaching, following roasting, depends primarily on its composition and on the conditions of the prior roast treatment, particularly with regard to the roasting temperature, the atmosphere maintained above the charge during roasting and cooling, and the presence of certain reagents. These factors, especially the last, virtually determine the extractions of uranium and vanadium attainable by carbonate leaching, as well as the reagent consumption on leaching, whereas adjustment of the leaching conditions has only a limited influence. These variables were examined systematically to elucidate roasting and carbonate leaching of carnotite ores and to establish a treatment yielding high recoveries of both uranium and vanadium. Tests were conducted on samples of four different Colorado Plateau ores, described in Table I. Roasting Procedure: The roasting tests were conducted in an electrically heated furnace in which the temperature was controlled to ±15°C. The ore (usually a 500-g charge) was ground to —100 mesh, mixed with the desired reagent, and spread in a silica tray to a bed depth of about 1/2 in. During the roast the charge was rabbled at intervals of 15 min. To provide free access of air the furnace was usually ventilated; however, in a few experiments a controlled atmosphere such as carbon dioxide or hydrogen was maintained above the charge. Leaching Procedure: The pulp, generally comprising 500 g of ore and a 2000-cc solution containing 80 g per liter of Na2CO8 and 20 g per liter of NaHCO3, was agitated in an autoclave at 120°C, under 30 psi 02. Samples were withdrawn periodically, and the solution and ore residue were analyzed. Under the conditions employed, maximum attainable extractions were generally achieved in 4

Jan 1, 1959