Search Documents

By E. Ray Webb

A interest to geologists and to mining and petroleum engineers is a laboratory method for determining the dip and strike of sub- surface structures, as well as the direction of fault planes traversing them. The information is derived by making use of the magnetic properties of borehole cores which must show visible representations of bedding or fault planes. Complete knowledge of these factors aids greatly in the successful exploitation of both ore and petroleum deposits.

Jan 1, 1940

Jan 1, 1969

By R. Ingerson

Bore surfaces of used guns commonly show a pattern of cracks in various degrees of development. It has been suggested that these cracks may aid erosion by providing channelways for the gases, eventually leading to the tearing out of blocks of metal. Under the general studies of gun erosion conducted at the Geophysical Laboratory it appeared desirable to consider this factor, and to determine the resistance to surface cracking offered by gun steel and by various other materials that might be used in the bores of guns. Method and Apparatus In order to make such a determination it is necessary to have (I) an arrangement in which the surface to be studied can be subjected to conditions similar to those in a gun with respect to temperature, pressure (developed by explosion gases), composition of the gases and length of time the surface is exposed to the gases; and (2) a specimen that can be examined readily after any number of shots, and then fired again, if necessary. The first of these conditions can be met by using an explosion vessel designed by H. S. Roberts of the Geophysical Laboratory. Fig I shows a cross-section of the apparatus. The "gun" G from which the charge is fired is made from the receiver of a caliber 0.30 army rifle, M1903, and the charges are prepared in caliber 0.30 cartridge cases. The test specimen S is held in place by a cone-shaped plug P and by a steel bridge B which is bolted to the outside of the explosion vessel on either side of the section shown. The plug, in turn, is held in place by a screw collar C. Maximum pressure is controlled by a brass rupture disk R. Part of the explosion gases flow past the two flat areas on S. Temperature and composition of gases, and the time before the rupture disk breaks, can be controlled by amount and kind of powder used, and pressure can be controlled by using rupture disks of different thickness. While the explosion vessel used was not designed so that temperature and pressure could be measured, in other vessels of closely similar size and shape containing proportionate charges of the same kind of powder as that used for standard testing procedure, values of 2700°K and 50,000 psi were obtained. Since the orifices past the flat areas on the plug are small compared to the rupture disk hole (I:I6), most of the gas goes out through the rupture disk when it breaks. The amount that goes by the plug depends on (I) the pressure attained before the rupture disk breaks and (2) the time it takes for this pressure to be built UP. The second condition (examination at will after any firing) is met by using for specimens short rods that have flat areas ground on opposite sides. These flat

Jan 1, 1949

By R. Ingerson

Bore surfaces of used guns commonly show a pattern of cracks in various degrees of development. It has been suggested that these cracks may aid erosion by providing channelways for the gases, eventually leading to the tearing out of blocks of metal. Under the general studies of gun erosion conducted at the Geophysical Laboratory it appeared desirable to consider this factor, and to determine the resistance to surface cracking offered by gun steel and by various other materials that might be used in the bores of guns. Method and Apparatus In order to make such a determination it is necessary to have (I) an arrangement in which the surface to be studied can be subjected to conditions similar to those in a gun with respect to temperature, pressure (developed by explosion gases), composition of the gases and length of time the surface is exposed to the gases; and (2) a specimen that can be examined readily after any number of shots, and then fired again, if necessary. The first of these conditions can be met by using an explosion vessel designed by H. S. Roberts of the Geophysical Laboratory. Fig I shows a cross-section of the apparatus. The "gun" G from which the charge is fired is made from the receiver of a caliber 0.30 army rifle, M1903, and the charges are prepared in caliber 0.30 cartridge cases. The test specimen S is held in place by a cone-shaped plug P and by a steel bridge B which is bolted to the outside of the explosion vessel on either side of the section shown. The plug, in turn, is held in place by a screw collar C. Maximum pressure is controlled by a brass rupture disk R. Part of the explosion gases flow past the two flat areas on S. Temperature and composition of gases, and the time before the rupture disk breaks, can be controlled by amount and kind of powder used, and pressure can be controlled by using rupture disks of different thickness. While the explosion vessel used was not designed so that temperature and pressure could be measured, in other vessels of closely similar size and shape containing proportionate charges of the same kind of powder as that used for standard testing procedure, values of 2700°K and 50,000 psi were obtained. Since the orifices past the flat areas on the plug are small compared to the rupture disk hole (I:I6), most of the gas goes out through the rupture disk when it breaks. The amount that goes by the plug depends on (I) the pressure attained before the rupture disk breaks and (2) the time it takes for this pressure to be built UP. The second condition (examination at will after any firing) is met by using for specimens short rods that have flat areas ground on opposite sides. These flat

Jan 1, 1949

By Shawn T. Sorrell, Carl Hrovatic

Original by Carl Hrovatic and Shawn T. Sorrell Revised by Carl Hrovatic Land is a precious resource and should be treated as such by all members of our society. The soil covering this earth is only a very thin outer layer, varying in thickness from a few inches to a few feet and covering the rocks and minerals lying beneath the surface. The wise use of this valuable commodity is the responsibility of everyone. Many everyday activities disturb the earth's surface. Examples are highway construction, housing and commercial developments, agriculture, and various types of mining. This chapter discusses the relationships of the environment to land as it applies to surface operations in the coal industry. Mining by surface methods disturbs, for a brief period of time, thousands of acres of land annually. In addition, refuse piles, slurry ponds, abandoned mine structures, unprotected mine openings, and unsightly cleaning plants can also adversely affect land unless properly handled. ACTIVE SURFACE MINING OPERATIONS Mining by surface methods includes rock quarries; sand and gravel pits; huge open pits to extract iron, copper, phosphate, and other ores; and coal mining. Production of coal by surface methods is now approaching 408.2 Mt/a (450 million stpy), amounting to almost 60% of the total coal output. Surface coal mining can be classified into the following five broad categories : Open-pit mining is practiced where coalbeds are extremely thick, as in some western states, or where coalbeds are sharply pitching, as in the anthracite region of the eastern United States. A typical open-pit mine, with coalbeds of 3.05 to 30.5 m (10 to 100 ft) or more thickness and a

Jan 1, 1981

By R. J. Mechin

TOP-SLICING was introduced in the Pachuca district in 1917 by T. C. Baker, at that time mine superintendent, of the Santa Gertrudis mine. There then existed 1200 ft. (365.7 m.) below the surface, lying between the fourteenth and eighteenth levels (a vertical distance of 108 meters) a block of ore having a length of 295 ft. (90 m.), and an average width of 82 ft. (25 m.) and dipping at an angle of 65°. This block lay in the hanging wall of the vein and consisted of highly altered and fractured andesite, cut through with mineralized quartz stringers. On the foot-wall side, 26 ft. (8 m.) of old filling, left by former operators, was of payable grade. Stoping therein was first undertaken by the square-set filling system, but because of the extremely heavy hanging wall and loose dry filling in the foot wall, all square setting had to be accompanied by spiling, which made the operation exceedingly slow and costly. A system of mining was sought that would eliminate the difficulties inherent to the square-set system in heavy ground and that at the same time would effect the desired economies in mining. After several years, top-slicing has met all the conditions most satisfactorily, so that when similar conditions presented themselves in El Bordo mine, this method was adopted with necessary modifications. El Bordo mine is operated by the Santa Gertrudis company, and is situated about two miles north of Pachuca. Because of the diversity of the orebodies, a number of different mining methods are in use, among them top-slicing.

Jan 10, 1925

By L. R. Ingersoll, James Fisher, Harry Vivian

The copper mines of the Keweenaw Peninsula in northern Michigan have long been of interest in connection with deep earth-temperature measurements. The extraordinary low geothermal gradient of l° F. in 223.7 ft. announced by Agassiz1 as a result of measurements dating from 1886, although later2 stated as in error, served to focus attention on this region as one offering, because of the great depth of the mines, unusual opportunity along this line. Lane,3 Van Orstrand4 and others have made valuable contributions to this study. Fresh opportunities afforded by the constant deepening of the mines, improvements in the accuracy and reliability of temperature-measuring instruments together with increasing knowledge of the heat conductivities and specific heats of the rocks, led the Michigan College of Mining and Technology in cooperation with some of the mining companies to renew work on this problem. It is planned eventually to complete a survey which will make use of the favorable opportunities for deep rock-temperature measurements presented in these mines. This survey should include the determination of a depth-temperature gradient in both conglomerate and arnygdaloid mines, and also the variations in temperature at the same depth in different geological formations. The first problem has a direct bearing on the question of providing equipment for necessary ventilation with increased depth. The second may show that a relation exists between the natural rock temperature and the mineral content of the formation. The measurements in all cases are to be guided by heat conduction considerations, to the end that they may represent as closely as possible

Jan 1, 1934

By M. G. Arthur

This paper is a theoretical analysis of fingering of water and coning of water and gas in homogeneous sand. Investigation of this idealized case illustrates the relative magnitude of the factors involved in actual conditions. The body of the report presents equations, example calculations, and charts that facilitate solution of such problems. Derivation of the equations introduced in this paper and a discussion of previously published equations are included in the appendix. Introduction Production of water from oil wells as a result of the pressure gradients established by flow of fluids through oil-~roducing sands is a common occurrence, which influences the cost of oil production, the degree of depletion and the efficiency of expulsion of oil from naturally occurring reservoirs. Control of water production and encroachment are important both in primary and secondary phases of of exploitation in order to produce oil and gas at lowest cost and in order to achieve the greatest ultimate recovery of the oil in the reservoir. Although many actual oil reservoirs present a multitude of variables that influence fingering and coning of water and gas, an inspection of the relationship and magnitude of the forces involved in the case of a homogeneous sand may indicate satisfactory methods of controlling water production. Application of equations relating the variables may indicate the geometric type of drainage that exists in a particular reservoir or in the vicinity of a particular well. A homogeneous sand body is assumed within the portion of the reservoir influenced by the well. Two geometric types of drainage are considered theoretically. The first is water fingering into an oil sand that is relatively thin compared with the lateral extent of the sand. This sand may represent the entire oil-producing reservoir or it may represent one interval in an oil reservoir, which is separated from other producing intervals by competent lithologic barriers to flow of fluids. For the condition of complete penetration of a well in such a sand body, it may be assumed that no flow occurs across bedding planes. A mathematical relation is developed between the limit of approach of a water finger to the well without being drawn into the well and the corresponding operating pressure drawdown. The second condition considered is that of water or gas entry into an oil well as the result of coning through bedding planes. The theory and graphical solution developed by Muskat' for the limit of approach of a water or gas cone to a well, without its entry into the well, related to the corresponding maximum pressure drawdown, is reviewed and amplified, Charts are presented, which facilitate graphical solution of the problem. A method is presented for the extension of this type of graphical solution to the case where gas and water coning occurs simultaneously~

Jan 1, 1944

By M. G. Arthur

This paper is a theoretical analysis of fingering of water and coning of water and gas in homogeneous sand. Investigation of this idealized case illustrates the relative magnitude of the factors involved in actual conditions. The body of the report presents equations, example calculations, and charts that facilitate solution of such problems. Derivation of the equations introduced in this paper and a discussion of previously published equations are included in the appendix. Introduction Production of water from oil wells as a result of the pressure gradients established by flow of fluids through oil-~roducing sands is a common occurrence, which influences the cost of oil production, the degree of depletion and the efficiency of expulsion of oil from naturally occurring reservoirs. Control of water production and encroachment are important both in primary and secondary phases of of exploitation in order to produce oil and gas at lowest cost and in order to achieve the greatest ultimate recovery of the oil in the reservoir. Although many actual oil reservoirs present a multitude of variables that influence fingering and coning of water and gas, an inspection of the relationship and magnitude of the forces involved in the case of a homogeneous sand may indicate satisfactory methods of controlling water production. Application of equations relating the variables may indicate the geometric type of drainage that exists in a particular reservoir or in the vicinity of a particular well. A homogeneous sand body is assumed within the portion of the reservoir influenced by the well. Two geometric types of drainage are considered theoretically. The first is water fingering into an oil sand that is relatively thin compared with the lateral extent of the sand. This sand may represent the entire oil-producing reservoir or it may represent one interval in an oil reservoir, which is separated from other producing intervals by competent lithologic barriers to flow of fluids. For the condition of complete penetration of a well in such a sand body, it may be assumed that no flow occurs across bedding planes. A mathematical relation is developed between the limit of approach of a water finger to the well without being drawn into the well and the corresponding operating pressure drawdown. The second condition considered is that of water or gas entry into an oil well as the result of coning through bedding planes. The theory and graphical solution developed by Muskat' for the limit of approach of a water or gas cone to a well, without its entry into the well, related to the corresponding maximum pressure drawdown, is reviewed and amplified, Charts are presented, which facilitate graphical solution of the problem. A method is presented for the extension of this type of graphical solution to the case where gas and water coning occurs simultaneously~

Jan 1, 1944

By W. E. Hale, G. J. S. Govett

An orientation survey was conducted over a known disseminated copper deposit and a Au-Cu vein deposit and employed geological, geophysical, and geochemical methods. Geochemical techniques proved the most effective and economical means of locating and defining areas underlain by these types of mineralization. Six additional, widely separated occurrences were also investigated and mineralization was confirmed by determination of cold-extractable copper in stream sediments. The length of anomalous drainage varies from several to 16 km and depends on the type and tenor of mineralization. Despite generally marked relief and extreme physical and chemical weathering, cold-extractable copper anomalies in soils appear to reflect closely variations in the ore mineral content of immediately underlying rocks. Threshold values vary with local geological conditions and type and grade of mineralization. Significant thresholds in stream sediments are about 65 ppm and 10 ppm for cold-extractable copper in disseminated and vein copper occurrences respectively. Similar differences are encountered in soils. This necessitates the use of a scale of threshold values at progressive stages in each exploration program. Dis-seminated copper occurrences are presently the major source of mineral production m the Philippines. Much potentially productive ground remains to be investigated and applied geochemistry appears to offer the best available approach. The Institute of Applied Geology (I.A.G.), a joint project sponsored by the University of the Philippines, the Philippine Bureau of Mines and the United Nations Development Program (Special Fund) undertook during 1965-66 a number of field projects in Northern Luzon Island (Fig. 1). These field operations were of a two-fold nature and involved both orientation and exploration. During approximately six weeks, an orientation survey, involving geological mapping, geophysical surveying and geochemical prospecting, was conducted over a partly developed, disseminated copper deposit at Santo Nino (Fig. 1). This study demonstrated the economic and technical feasibility of geochemical ptospecting, relative to the other methods tested, for the location and delineation of a typical disseminated copper occurrence characteristic of those that represent the major source of metal in the Philippines.' Geochemical techniques, similar to those tested at Santo Nino, were then applied in a second orientation study of a vein occurrence at Suyoc (Fig. 1). The results of these two orientation studies suggest that, in reconnaissance work in this region, stream sediment analyses, combined with the determination of pH in the same streams, can be used to indicate areas underlain by rock containing anomalous concentrations of copper, whether it occurs in the large tonnage, low grade, disseminated deposits or in the comparatively small tonnage, higher grade, gold vein occurrences. Furthermore, the orientation surveys demonstrate that soil sampling and analysis serve effectively to outline more closely the mineralized zones within the generally anomalous areas identified from the stream reconnaissance. To further test the methods selected from the two earlier trials, six additional, widely separated prospects were investigated. The geological and geochem-

Jan 1, 1970

By F. B. Plummer

PROGRESS during 1940 in oil-production technology has been confined largely to a steady advancement in practices inaugurated in previous years, rather than the introduction of any new startling process or technique. The usual changes, improvements and additions in production equipment have been introduced. An increased attention to, and interest in, research has been noteworthy, resulting in improved efficiency in operation of oil wells. control, utilization of reservoir energies and reduction of production costs.

Jan 1, 1941

By Sherwin F. Kelly

LITERALLY from the four corners of the earth, from Jerusalem and China, from Mysore and Uganda, as well as from geophysicists in the United States, came contributions from workers in magnetic and electrical geo-physical methods, most of them unfortunately unable to be present themselves. The most lively discussion centered on the phenomena of natural potentials in the earth, dealt with in M. B. R. Rao's paper from Mysore, and in Parke Dickey's contribution, which he presented in person. In the oil fields, the weak potentials observed in sedimentary strata traversed by bore holes have traditionally been ascribed to phenomena of electro-filtration and electro-capillarity. Research tending to refute this theory was presented by Dickey, who reported the existence of natural potentials in core samples, and between strata exposed in underground workings. This precipitated a lively discussion as to the possible role of electro-filtration, selective adsorption of ions by mineral particles, and electrolytic potentials, in the production of this phenomenon.

Jan 1, 1943

By R. HAYDEN, H. B. HALLOWELL, H. O. Hofman

THE object of refining copper in the reverberatory furnace is to obtain a metal which will have the highest attainable degree of malleability, ductility and electric conductivity, and present at the same time a level surface when it solidifies in the mold after casting. These desirable physical properties are governed by the character of the impurities and the forms in which they are present, by the amount of cuprous oxide retained by the copper, by the quantity of gas held in solid solution, by the casting-temperature, and by the thickness of the casting. The effects of impurities, of cuprous oxide and of gases upon the mechanical properties of copper have been studied by Hampe in his classical paper "Contributions to the Metallurgy of Copper." The most recent research into the effect of metals upon the electrical conductivity of copper is that of Addicks.2 The influence of cuprous oxide upon the electrical conductivity has been investigated by Walker' and Addicks.4 The absorption of gases has received' attention by Hampe,5 Stahl 6 and Heyn.7 The effects of casting-temperature have been noted by Stahl.8

Mar 1, 1907

By Harvey Brooks

Jan 1, 1963

W. M. CURSE, Mansfield, Ohio.-Outside of the commercial valu-ation of the material, for what purpose does this alloy-90 per cent. of copper, 6 ½ per cent. tin, 2 per cent. zinc, and 1 ½ per cent. Lead-seem to be eminently fitted? C. P. KARR.-So far as our tests go, it would be eminently fitted for steam valves and pistons, and for the work for which 88-10-2 bronze is generally used, although for very large castings it would not be superior to 88-8-4 bronze. P. E. MCKINNEY, * Washington, D. C.-Some time hack, clue to a desire to avoid some of the objectionable features of 88-10-2 bronze, particu-larly on heavy castings, also to save tin where possible, we took up the question of a substitute for 88-10-2 bronze, where red bronze was ordinarily specified. After trying most of the mixtures, we found that when using as low a tin content as is given in this proposed composi-

Jan 12, 1919

By Samuel B. Christy

Jan 1, 1889

By William Phillips

THE earliest mention of the sulphur deposits in what is now Culberson County, Texas, seems to be contained in "Explorations and Surveys for a Railroad Route from the Mississippi River to the Pacific Ocean, United States War Department, 1853-54." Captain John Pope (he was not commissioned Captain until 1856) had charge of one of the divisions of the Survey. In his report on the geology of the route, William P. Blake noted the analysis of a greenish earthy powder from the bed of Delaware Creek, at the springs, which contained 18.28 per cent. of free sulphur. The report states: "From the chemical examination of the waters of the spring, by Dr. Booth, it appears that chloride of sodium is the principal solid ingredient, but considerable quantities of sulphide of sodium are present. * * * * * The waters from the springs examined by Dr. Booth were alkaline, but it is possible that some of the springs are acid; and in this case the precipitation of sulphur would ensue on the mixture of the acid waters with those charged with alkaline sulphurets and the origin of the deposits of sulphur would he thus explained." This is the first reference to the existence of sulphur in that region, the first mention of the character of the water found there and the first suggestion as to the' origin of the deposits. The possibility of the existence of acid waters was confirmed by E. M. Skeats, nearly 50 years later.1 In this publication, Skeats says that the water from the sulphur deposits in Section 11, Block 114,, Township 5, contains 79.08 grains of free sulphuric acid per gallon. This locality is about 13 miles (21 km.) south of Delaware Creek and about 35-miles (56 km.) east of the Delaware Springs. The next published reference to the existence of sulphur in Trans-Pecos Texas is in the First. Annual Report of the Geological Survey of Texas, 1889, page 226, where W. H. von Streeruwitz mentions that sulphur is found in that region, but gives no further information. In the

Jan 9, 1917

By P. A. Vukmanic, M. Gensamer

Only recently has it been realized that preferred orientations are common in hot-rolled steels. In a recent paper, N. P. Gossl stated that hot-rolled mild steel exhibits a texture different from that characteristic of cold-rolled steel. No complete study of these hot-rolling textures has been reported using the pole-figure method of Wever. The material used in the work reported in this paper was the same material used by Gensamer and Mehl2 in a recent study of preferred orientations in cold-rolled steel, to which reference may be made for the composition and thermal history of the steel. Automobile-body sheet bar 1/4 in. thick was hot-rolled at two temperatures, 780' and 910' C. (1436' and 1669' F.). These temperatures refer to the temperature of the furnace in which the steel was heated; after each pass the steel was returned to the furnace and held there long enough to return to temperature. Although no accurate method was used to measure the temperature after each pass, it was estimated by color that only a slight drop in temperature occurred. In order to determine the effect of any preferred orientation that might have persisted through the normalizing treatment, one specimen at each temperature was rolled in the same direction as the original working direction and the other at right angles to it. The total reduction in each case was 85 per cent, the specimens having been reduced from 0.250 to 0.0375 in. in five passes. Final cooling was in air. Pinhole reflection photograms were taken of all four specimens, with the rolling direction vertical and the X-ray beam at an angle of 7' with the transverse direction (the transverse direction is defined as that direction in the rolling plane perpendicular to the rolling direction). These photograms, taken with a Mo target at 35 kv., are reproduced in Figs. 1, 2, 3 and 4. They show that a more pronounced texture was developed by the low-temperature rolling (780' C.), and that of the two

Jan 1, 1937

By B. K. Larkin, H. R. Bailey

One of the most complicated and potentially one of the most promising secondary recovery methods is that of underground combustion. A number of field tests1,2,3 have been performed recently, apparently indicating that the underground combustion process is technically feasible. Relatively little has been published concerning laboratory or theoretical investigations of the underground combustion process. A few results of laboratory tube runs have been published4,5 and these data are valuable in understanding the process. The tube run data also emphasize the complexity of the thermal recovery process. Under various conditions, problems in heat transfer, multiphase fluid flow and combustion rates arise. For example, at low temperatures the combustion process proceeds so slowly that the front cannot be propagated. It is a problem in heat transfer to predict what injection rate of air is necessary to sustain combustion in a particular reservoir. Certain fluid flow aspects of underground combustion have been studied by Wilson, et a13. In the development of some of the flow equations, assumptions of adiabatic combustion were made. Vogel and Krueger1 have devised an analog model of the heat conduction process for a constant temperature cylindrical source moving radially outward in a homogeneous conducting medium. Jenkins and Ramey7, in a discussion of the Vogel and Krueger paper, present an analytical solution of a heat conduction problem related to problems considered by Vogel and Krueger. In the present paper an idealized model of the heat conduction problem is considered, which is more general than the model of Vogel and Krueger or Jenkins and Ramey. In particular, initial well heating, vertical heat losses and arbitrary frontal velocities are included. Equations for the temperature are obtained in terms of integrals. These integrals have been evaluated numerically for the case of frontal movement corresponding to a constant air injection rate and the case of constant frontal velocity. These results are presented graphically. From these graphs one may estimate conditions under which nearly adiabatic temperatures are obtained. The application of these results requires some knowledge of reservoir thermal properties, combustion rates and residual fuel content. Assuming no vertical losses it is possible to obtain explicit evaluations of these integrals in the linear con- stant velocity case and in the radial case corresponding to a constant air injection rate. PRESENTATION OF RESULTS The geometry of the radial system is illustrated in Fig. 1 where the reservoir is represented as a slab of thickness h. By making an energy balance for an infinitesimal volume, one obtains the following equation. T= x T+F(z.r).........(1) where F (z,r) =HWv1/pc (r-r1), if z h/2 = 0, if z >h/2 . In Eq. 1, V- represents the Laplacian operator and 8 is the Dirac delta function. Eq. 1 is the well-known diff-sion equation with a source term and may be applied to a linear system. For example, if the source is moving in the direction of the x axis, then the argument of the delta function is x - 1,. In deriving Eq. 1 the following approximations were made concerning the actual combustion process: (1) all heat transfer is by conduction in a homogeneous medium, (2) the formations bounding the reservoir have the same thermal properties as the reservoir, (3) the combustion fuel is consumed instantaneously as the front arrives, (4) there is a constant fuel concentration

By AIME AIME

Russell B. Paul, Chairman of the Special Committee on Divisional Relationships, presented the interim report of his Committee which was published in the September, 1945, issue of MINING AND METALLURGY and a copy of which is incorporated in the official minutes of this meeting. The following specific actions were taken by the Board of Directors in relation to the six recommendations in the Summary of the Report as published: (1) Mr. Haider, Chairman of the Petroleum Division, presented the formal request of his Executive Committee that the headquarters of the new Secretary of the Petroleum Division be established in Dallas, Texas. After lengthy discussion in which the point was made that the success of this program would depend upon effective co-operation between the Chairman of the Division, the Secretary of the Petroleum Division, and the Secretary of the Institute, the request was approved. The new secretary will be selected by the Division and will be employed by the Institute in the capacity of an Assistant Secretary. (2) The following item in the report was approved:

Jan 1, 1945