Search Documents

By M. Cohen, D. J. Blickwede

Quantitative observations concerning the carbide phases in high speed steel are of importance for two general reasons: (1) the carbides, being inevitable constituents of the final structure, exert a direct influence on the properties of the steel; and (2) a substantial proportion of the total alloy content is tied-up in the carbides, and hence the extent of their solution on austenitizing governs the composition of the steel matrix. The latter relationship has a vital bearing on the response of the steel to tempering as well as on its performance in subsequent service. Accordingly, in the course of a long-term study of the behavior of high speed steels, the authors were confronted with the problem of securing quantitative data on the carbide phases. The obvious method for acquiring such information is to isolate the car-bides from the steel and subject them to chemical, X ray diffraction and other measurements. There are well-known extraction techniques which involve the chemical or electrolytic solution of the less noble matrix (ferrite, marten-site or austenite), thus leaving a residue of the carbide phases. However, the results obtained must be scrutinized carefully1,2 since the carbides may be affected by the chemical or electrolytic action. It is the purpose of the present paper to describe the experiments leading to an electrolytic-extraction technique for quantitatively isolating the carbides from both I and hardened high speed steel. Particular attention is paid to the amount, as well as the composition, of the carbides so that the matrix analysis becomes ascertainable by subtraction from the overall steel composition. Illustrative results are given for the M-2 grade of tungsten-molybdenum steel. Review of the Literature The chemical method of dissolving the matrix selectively with respect to the carbides makes use of dilute non- oxidizing reagents such as hydrochloric or sulphuric acid. Although this simple procedure has led to the determination of the cementite composition,3,4 it achieved only limited success because of the interaction between the acid and the carbide residue. Some of the carbides may not only be destroyed in this way, but the hydrogen released is likely to remove part of their carbon as hydrocarbon gases. The electrolytic technique of isolating carbides has the advantage of rapidly dissolving the specimen (anode) in the presence of less reactive solutions than are practicable with the chemical method. This reduces the possibility of chemical attack on the carbides, and furthermore, the hydrogen evolved during the electrolysis is released at the cathode which is not in close proximity to the carbides. The common electrolytes adopted for this purpose are hydrochloric and sulphuric acids.5-l1 Aqueous solutions of ferrous salts have also been used.12,13 A considerable advance in experimental technique was introduced by Treje and Benedicks14 who developed a double-compartment cell for electrolytic extraction, the anode and cathode chambers being separated by a porous diaphragm. A solution of 15 pct sodium citrate, 2 pct potassium bromide and 1 pct potassium iodide was selected for the anolyte, while the catholyte consisted of a 10 pct solution of copper sulphate, with copper serving as the cathode. This type of cell has a number of desirable characteristics: 1. The anolyte has a pH value close to 7, at least at the beginning of the run. 2. The iron that dissolves from the anode-specimen forms a water-soluble complex ion with the citrate, thereby preventing the precipitation of iron hydroxide (which would contaminate the carbide residue) despite the neutrality of the solution. 3. Copper deposition instead of hydrogen evolution occurs at the cathode, and this avoids an increasing concentration of hy-droxyl ions which (in an otherwise neutral solution) might cause the precipitation of insoluble hydroxides. 4. Contamination of the anode chamber by copper sulphate is inhibited by the porous diaphragm. Houdremont and coworkers15 applied the above method (with the further refinement of excluding oxygen during the electrolysis, washing and drying) to the extraction of carbides from a series of plain carbon steels after various heat treatments. They had quantitative success only with specimens in the annealed condition, and concluded that the size and shape of the carbide particles play an important role in the isolation process, with large spheroids exhibiting the least tendency to decompose during the electrolysis. Up to the present time, the citrate double-cell has not been used to any extent for isolating the carbides of high alloy steels, apparently on the grounds that the complex carbides are more resistant than cementite to attack in the simpler acid electrolytes. In particular, Bain and Grossmann7 and Gulyaev10.10a have employed the hydrochloric acid cell for their investigations of the carbides in high speed steel.* It will be demonstrated here that this type of cell is capable of yielding quantitative results in the case of high speed steel, and actually has certain advantages over the more complicated double cell. However, in order to provide a rigorous test of the quanti-tativeness of electrolytic procedures for the problem at hand, both methods were studied in considerable detail.

Jan 1, 1950

By P. R. Sperry, P. A. Beck, J. Towers

Dahl and Pawlek1 found that electrolytic copper develops extremely coarse grains at 1000°C after about 90 pct reduction by rolling. This coarsening occurs only under conditions of penultimate grain size, deformation, and alloying which lead to the "cube" recrystallization texture.l,2,3,5 The peculiar angular shapes and straight grain boundaries of the coarse grains were noted by several investigator.1,4,5 On the other hand, coarsening in Fe-containing aluminum or in AI-Mn alloys8 does not depend on a "cube" (or any well developed) recrystallization texture. It is true that increasing deformation by rolling, and, therefore, an increasingly well developed re-crystallization texture, are associated with decreasing incubation periods of coarsening.6-7-8 Nevertheless, coarsening readily develops in aluminum even after only 30 pct reduction by rolling, where the recrystallization texture is very weak.6,8 Also, coarsening was observed by Jeffries9 many years ago in sintered thoriated tungsten, which presumably has no preferred orientation. In all these cases coarsening is associated with grain growth inhibition by a dispersed second phase.8,9 The annealing temperature has to be suficiently high to overcome the inhibition at a few locations. But if it is too high, growth starts at many points, and the resulting grain size becomes much smaller.9 Normally, the coarse grains are more or less equiaxed, and the boundaries have a typical ragged appearance.6.8 Cook and Macquarie4 demonstrated that, in addition to the texture-dependent coarsening previously found at 1000°C,l electrolytic tough pitch copper may also coarsen at 800°C after 50 pct reduction by cross rolling. The coarse grains formed under such conditions have rounded shapes and ragged boundaries, like those in aluminum. When the annealing temperature is higher, the tendency for their formation decreases. All these observations suggest that the coarsening at 800°C is associated with inhibition by a second phase. Actually, coarsening at 800°C after 50 pct reduction by cross rolling was observed only in tough pitch copper,4 which contains Cu2O particles. On the other hand, the texture-dependent 1000°C coarsening occurs in both tough pitch and oxygen-free copper;4 it does not appear to depend on the presence of a dispersed second phase. However, the interpretation of the 800°C coarsening in Cu after 50 pct rolling as an inhibition-dependent process, similar to the coarsening in A1-Mn alloys, is somewhat weakened by the fact that this coarsening was reported4 to occur only after cross rolling, and not after straight rolling. It was, therefore, decided to re-examine this question. A 1 in. diam electrolytic tough pitch copper rod, No. 2 hard drawn, was annealed for 20 min at 700°C, rolled to 0.5 in., annealed 10 min at 700°C, and straight rolled to 0.064 in. It was then given a penultimate anneal of 20 min at 500°C and it was cut into four sections, which were given final reductions by straight rolling as follows: A 30 pct reduction of area B 50 pct reduction of area C 70 pct reduction of area D 90 pct reduction of area Specimens cut from the four sections were finally annealed at 800°C in an oxidizing atmosphere. Strip A remained fine grained up to 10 hr, but the specimen annealed 12 hr consisted of only 2 large grains. Strip B had a few scattered large (1/2 to 3/4 mm) grains after 1 min, although the balance of the specimen consisted of fine grains of about 0.02 mm. After 5 min there were several 10 to 15 mm grains present, and after 1 hr strip B was completely coarsened. The coarse grains had the same characteristics (see Fig 1) as those obtained by Cook and Macquarie at 800°C after cross rolling. Strip C had several grains of 0.05 to 1 mm after 1 min, but it was still largely fine grained after 12 hr. After 48 hr it consisted entirely of grains of about 0.5 to 4 mm, with an extraordinarily large number of twin bands. Strip D remained com- pletely fine grained after 4 hr at 800°C. These results indicate that, in the deformation range of 30 to 70 pct reduction, the incubation period for coarsening as well as the rate of growth and the final size of the coarse grains decreases with increasing deformation. Similar

Jan 1, 1950

US 4,152,143-Continuous precipitation of cement copper from an aqueous ore leach solution mixed with pieces of iron as the precipitant Copper depositing on the pieces of iron is loosened and removed therefrom by means of constant but regulated oscillating movement of the pieces of iron in a horizontal elongated chamber, and the loosened copper is separated and collected from the mixture E Kausel and R Nissen, assigned to Klockner-Humboldt-Deutz A G May 1, 1979 8 pp (75-100) Filed 1-12-78 (868,981) (Drawings below) [ ] US 4,156,711-Removal of metal impurities from an acidic zinc or cadmium solution prior to electrolysis. Impurities such as manganese, cobalt, nickel, and thallium are selectively precipitated by contacting the solution with persulfuric acid or an ammonium or alkali metal salt thereof while maintaining a pH value of from 1 5 to 4 5 This patent is a continuation-in-

Jan 1, 1980

By W. H. Bassett, C. H. Davis

ALTHOUGH brasses and bronzes have been made for ages, a systematic study of their physical properties has been carried out only during the years of the present century. Among these properties may be included those which are to be detected by means of microscopic examination; in other. words by the science of metallography. The earlier workers in this field, both in this country and abroad, gave their attention to steel. When the senior author explored the situation in 1902, there was little encouragement to be found in undertaking the study of the non-ferrous alloys. A start was made, and the metallography of the brasses and bronzes, as well as of the copper-nickel-zinc alloys developed materially under his direction. Annealing experiments were begun in 1902, and in the succeeding years the effect of temperature, and the influence of previous working, on the grain size of brass were studied. The conclusions so well known and widely published today were largely reached during those earlier years. . In 1905 the first complete annealing series were made. By this it is meant that brass and copper sheet, 5 B & S Nos. hard, was machined into tensile test specimens, then annealed under accurate control for 30 min. at temperatures up to the melting point of the material. Various determinations were made, including tensile strength and elongation in 2 in. There rapidly followed similar series on all of the copper-zinc alloys from 100 to 60 per cent. copper, on the bronzes, cupronickels, and on copper-zinc-nickel alloys. At this point there was published by Grard, in October, 1909,1 the very comprehensive and complete work on the tensile properties of cartridge brass, 90-10 copper-zinc, and electrolytic copper. The excellent photomicrographs in that paper illustrated the changes in structure produced by cold rolling as well as by annealing at different temperatures, but where Grard's work was confined to copper and to two alloys, the investigations in this laboratory have been over the entire fields of the commercial copper-zinc alloys, copper-tin alloys, representative copper-nickel and copper-nickel-zinc alloys as well as aluminum bronzes and others of a more special nature.

Jan 1, 1928

Edward A. UehlinG, New York City (communication to the Secretary*):—Mr. Baker's paper is one that brings up a subject of great importance, and if full statistics could be collectecl of the number of furnace-linings ruined by reason of bad distribution by skip-hoists, it would be found an astonishing array. Unfortunately a universal remedy has not yet been found. The fact that Mr. Baker has apparently succeeded in overcoming the trouble at Sydney, is no guarantee that the same remedy applied at another plant, where very different or even slightly different conditions prevail, mould cure the trouble. That it requires but a slight continuous difference of penetrability in the column of the descending stock of one section, over another, to produce channeling, is clearly demonstrated by Mr. Baker's experiments, by which he reversed the channeling from front to rear instead of remedying the trouble. Every change in the physical make-up of the charge necessarily requires a specific adjustment; even supposing this feasible, the regular working of the furnace is by no means assured, because with the high pressures now customary, the tendency of the ascending gases to plow their way through in a direct course, prevails, and having once opened up a passage, they will persist and cause trouble. Homogeneous filling-, hard driving and regularity of working are incompatible. The higher the furnace, the greater the

Jan 1, 1905

By AIME AIME

OUR own Institute of Metals and Iron and Steel divisions cooperated with the Iron and Steel Division of the American Society of Mechanical Engineers, the American Welding Society, and the American Society for Steel Treating in a busy week at Cleveland. The morning sessions were held at the Hotel Cleveland and the afternoon ones at the Auditorium, where the metallurgical exhibition under the auspices of the American Society for Steel Treating not only occupied the arena of the Auditorium but completely filled the huge adjacent Annex. In the intervals of sessions the members thronged the exhibits but in the evenings the local attendance was so great that if the crowds had been any larger it would have been difficult to see the exhibits. With so many firms, both producers of metals and of equipment accessory to their production and use, it would be impossible to mention them -all and unfair to single out a few, since no two individuals' judgment would coincide as to relative interest and importance. In any case an exhibit is a thing to be seen rather than described, and these were well worth seeing.

Jan 1, 1929

By Robert L. Haffner

When mining operations of The Eagle-Picher Co. began in the Illinois-Wisconsin zinc mining field in 1949, all underground loading of broken ore and waste was by caterpillar-tracked machines. Beginning in 1956 rubber-tired end-loaders were brought in; ultimately they completely supplanted the tracked units. End-loaders proved to have the mobility needed for the mining conditions and additional merit in auxiliary capacities. Eagle-Picher operates five mines in this area; two are entered by shafts and three by inclined adits. Several ore zones, some of which are attenuated over a considerable distance, are worked from the same entry. Consequently underground haulage roads connecting or following these orebodies have attained great length. In addition, working places are often widely separated because of the character of the mining operations which include pillar recovery and extending haulage connections into old workings. At one mine, the haulage distance is 5000 ft on either side of the shaft, at another the maximum one-way distance is 8400 ft, and at another the present road system of 6800 ft is expected to reach 10,000 to 12,000 ft.

Jan 6, 1962

The year 1934 saw a very thorough and intensive search for oil in Italy, both by the Government-subsidized company, the A.G.I.P., and by the few smaller operating companies. Approximately two-thirds of the exploration work, however, has been done in the Province of Emilia (northern Italy). The A.G.I.P. has been particularly active in the Emilia district and has sunk several rotary holes between Voghera and Ferrara on structures located by geophysical means in the Po Valley. Only insignificant amounts of oil have shown up in these tests to date but gas has been found in fair quantities, and apparently the company is not yet prepared to abandon its search in this part of the country without further effort. In Central Italy, the same company has put down four tests with cable tools and of these two were "dry holes" and the other two found only traces of oil. The A:G.I.P. also sank two wells in southern Italy and it is believed that in these the indications were sufficiently encouraging for the exploration work to be continued. No serious drilling has yet been done in Sicily by the A.G.I.P. or any other company. The annual subsidy granted to the A.G.I.P. by the Government for the duration of its five-year plan has been considerably reduced for 1935 and this may interfere with the completion of the coming year's program in all its details. The Società Petrolifera Italians, which is the chief producing company in the country, has continued the development of its two fields, Salsomaggiore and Vallezza, and at the same time has intensified its program of exploration. Rotary machinery has been introduced and is undergoing a thorough trial, and prospects of finding new pools at greater depths are considered good. The charcoal adsorption plant at Vallezza has operated satisfactorily throughout the year and has produced nearly 3000 bbl. of high-grade gasoline. Besides the exploration well at Rile dell'Olio, which is still drilling, another wildcat test has been started at Torre-di-Traversetolo. All operations of this company are confined to the district of Emilia. The Società Petroli d'Italia has continued to operate the old fields of Montechino, Gratera and Velleja, and has a well now exploring at greater depths in that general area. Of the two exploration wells in the Torino

Jan 1, 1935

By J. A. Hutcheson

NO one questions that it is technically possible to achieve the controlled release of atomic energy in a form that can be converted into heat or electricity. However, before this is actually an accomplished fact a great amount of work must .be done. This work falls into two general classifications: research and engineering development. At present a research program is under way in this country, co-ordinated and directed by the Atomic Energy Commission, which, as time goes on, will uncover fundamental knowledge of this new science that is essential before industrial applications of atomic energy are practical. Undoubtedly therefore, as the store of available knowledge increases, a time will come when answers to the many questions relating to practicality of atomic energy in industry can be determined with reasonable certainty. That the application of atomic energy in industry will eventually be proved practical is assumed. What then are the engineering problems that must be solved before the first practical electric power generating station can be built?

Jan 1, 1948

By John B. Cook

Most of today's open pits take the form of conical-shaped excavations in the relatively flat or undulating terrain surrounding them. Ore is usually hauled uphill from the pit bottom by truck, rail, or skip to crushing, beneficiation, railroad loading, and stockpiling facilities near the edge of the pit. There are, however, a few orebodies whose locations in mountainous terrain causes special problems that generate different technical solutions. LAMCO's 10.5 million metric tons per year high-grade iron mine in the Nimba Range in tropical Liberia is probably one of the most extreme of these exceptions (Fig. 1). At Nimba there is a 2,000-ft difference in elevation between the upper- most levels of the orebodies and the start of the railroad below at the foot of the mountain. Haulage to the crusher is usually downhill at grades of up to 12% dictated by the topography of the rugged terrain. Ore is transported from the crusher down the mountainside by a conveyor sys- tem 10,096 ft long, whose average grade is 18%. The belt is braked by asynchronous generators, feeding power into the local network. The original crusher must be relocated at a lower elevation outside the final pit limit to allow that part of the mountain on which it now stands to be excavated. HISTORY The LAMCO Joint Venture is owned 75% by the Liberian-American- Swedish Minerals Co. (LAMCO) and 25% by Bethlehem Steel Corp. LAMCO is comprised of a 50% interest by the Liberian Government and 50% interest by Liberian Iron Ore Ltd (Fig. 2). This joint venture was launched to develop the high-grade iron ore deposits of the Nimba Range.

Jan 1, 1969

By Kenneth R. Hancock

Iron oxides are unique in that they are the only significant colored mineral found in a natural state suitable for use as a pigment after being pulverized to pigmentary size. The current world production of iron oxide pigments is estimated by the author to be between 499 and 590 kt (550,000 and 650,000 st) based on 1979 data. The fact that highly colored natural deposits of iron ore are found throughout the world accounts for its use in prehistoric man's artistic cave paintings. These early artists did not realize that they had established man's first paint test fence which now has some 20,000 years of exposure. In addition to abundance, constituting about 7 % of the earth's crust, iron oxides have the advantages of low cost, permanency, and are not toxic. Through the centuries, succeeding civilizations have utilized iron oxides as a major source for decoration and protection when coloring was desired. In the last century the chemical industry has improved on nature by developing a complete range of synthetic iron oxide pigments which surpass the pigments produced from natural iron ores in uniformity, color quality, and chemical purity. In the United States alone, the combined production of natural and synthetic iron oxides produced sales of over $28,000,000 in 1970 (Stipp, 1970) and increasing to $97 million by 1980 (Spinrad, 1980). Nomenclature With the increasing importance of the synthetic iron oxides it is necessary to make a distinction between the natural or mineral pigments and the synthetic pigments. Natural pigments are those products which are derived from selected ores and should not be confused with iron ores mined for steel production. Iron ores that are mined for steel must be capable of being mined and reduced to iron on a commercial basis. These ores are selected on the basis of iron content and processing economics. It is therefore unusual when iron ores for steel production are suitable for use as mineral pigments. Natural pigment ore sources are selected for their special physical-chemical properties and can command a premium price. Synthetic pigments, and in this instance iron oxides, are those pigments produced from basic chemicals. Through chemical synthesis pigmentary sized particles are produced as opposed to comminution, the major procedure common to all natural iron oxide pigments. Classification An important characteristic of a pigment is its color and, therefore, a logical separation can be made on this basis. A. Yellow Iron Oxide Pigments 1. Natural mineral origin a) Goethite b) Lepidocrocite c) Ochres d) Siennas e) Limonite 2. Synthetic pigments a) Goethite B. Red Iron Oxide Pigments 1. Natural mineral origin a) Hematite b) Siderite (calcined) c) Pyrites (calcined) 2. Synthetic pigments a) Hematite C. Brown Iron Oxide Pigments 1. Natural mineral origin a) Umbers b) Limonite (calcined) c) Siderite (calcined) d) Goethite (bog ore or sulfur mud) 2. Synthetic pigments a) Blends of hematite, goethite, and magnetite

Jan 1, 1983

By M. H. Forester, John D. Cooner

ANTHRACITE ALTHOUGH the unmined anthracite will last for approximately 150 years, most of the thicker and cleaner coal beds have been almost entirely first-mined and pretty well robbed, leaving much of the present and future production to come from thin and dirtier beds. Herewith is a section of one of the dirty beds being mined in the Wyoming region [ ] This section shows that 45.8 per cent of the bed is made up of impurities and that the 45 in. of coal in the bed is in five benches, the thickest of which is 19 inches. In some localities of the anthracite region there are 14 beds of minable coal. Orderly and proper mining of the coal makes it necessary to rob or second-mine-almost all beds have already been first-mined-in sequence from the top downward. Therefore the robbing of the few remaining portions of the thicker and cleaner beds is in many instances being held up by the mining of the overlying thin and dirtier coal beds. Impurities Impurities consist of fire clay, slate, rock, and bone. The latter, which is black, contains 40 to 60 per cent carbon and often resembles good coal. In some beds there are also bands of "blue" coal, which, as the name implies, is of a bluish slaty color. Although much of this "blue" coal has a carbon content almost as high as the good anthracite, it is not

Jan 1, 1943

By C. K. Leith

WE face the postwar problem of the use of minerals as sanctions to control the armament and the re-armament of the Axis powers at the source, minerals being the raw material of armaments. That is the subject of today's discussion. It is one thing to talk about controlling minerals in the interest of rearmament, and it is another thing to put any such ideas into effect. A provision for min- eral sanctions-not by that name but under broader terms-was contained in Article 16 of the League of Nations, and an attempt was made to apply min- eral sanctions when Italy cut loose in Africa. That was a failure because the plan was badly thought out. They did not have the right minerals included in the list. Also, they did not have the machinery set up at all. Somebody said to the League of Nations: Let's apply the sanction, and it was assumed that that was all that was necessary. It turned out to be a rather sad perfor- mance. However, that certainly cannot be taken as an example of what will happen if a properly thought-out pro- gram is adopted.

Jan 1, 1944

By Clyde Williams

A MAN who is a first-class metallurgist, engineer, and scientist and an outstanding organizer, administrator, and executive and who, at the same time, has an innate ability to "make friends and influence people" everywhere he goes is an exceptional personality at any time. And if such an individual can retain this combination of virtues during a great war despite the fact that the Government loaded him with enough work and responsibility for three such men. he is a most exceptional personality. And if he can keep his head and maintain an unfailing sense of humor during the trying war years and, while dealing with hundreds of jittery metallurgists and metalworkers, with Army and Navy brass, and with red-tape-entangled war agencies by the dozen, he is a rare personality indeed. Such a man is Clyde Williams, director of Battelle Memorial Institute. who will be President of AIME in 1947. The Institute is fortunate in having him as its mentor during what may be a critical and important year.

Jan 1, 1947

By C. A. WARNER

IN all the meetings of the Petroleum Division, emphasis was placed on the essential importance, in the successful furtherance of our war effort, of efficiently producing, transporting, refining, and utilizing maximum quantities of crude oil and natural gas with the minimum expenditure of critical material. With representatives present from all branches of the petroleum industry, from all parts of the United States, the sessions were opened Tuesday morning with Commander Harry P. Stolz. U.S.N.R., Chairman of the Division, and A L. Haider as associate chairmen. From that time until the symposium on petroleum economics was closed Thursday afternoon papers of exceptional interest and importance were presented and discussed in a most frank and open manner.

Jan 1, 1943

By T. M. Girdler

INDUSTRIAL progress and development in this country from the earliest daps to the present has proceeded at an ever-quickening pace. Yet during recent decades the nature of our industrial progress and development has undergone a change of great significance. The earlier days were a period of tremendous expansion. Population was increasing by leaps and bounds. Vast areas of new land were being .2 opened to settlement. And almost boundless new sources of timber, coal, oil, ores, and power were being opened to ever-expanding markets. Today, however, that picture has al- most completely changed. Today, with population increase tapered way off and the opportunity for free expansion into western frontiers gone, the great industrial development of our country continues on a vastly different front. Industrial progress and development today rest on a foundation of technology. The key- stone is research. Our frontiers to- day are frontiers of sciencec

Jan 1, 1939

By A. J. Boynton

THIS paper is not the result of recent research with regard to any particular feature of iron metallurgy, blast-furnace practice or mechanical engineering. It is rather a series of notes with regard to contemporaneous progress in blast-furnace construction and operation, together with some suggestions as to changes and improvements that seem to be desirable. On April 1, 1930, a committee of the Chicago District Blast Furnace and Coke Association presented to that association a rather ambitious study of blast-furnace equipment, together with recommendations for the design of construction of a complete blast-furnace unit for the production of 1000 tons of pig iron per day. This report represented the result of months of study by members of the committee, all of whom were actively engaged in operation or design of blast-furnace plants. It is natural, therefore, that comments on the present state of the art should take this 1000-tons furnace, as recommended by the Association, as a basis for comparison with corresponding features of construction or design. See Table 1. In looking through this report at the present time, the significant difference is in the nature of the gas-washing equipment that today would be specified. In other respects, the installation would remain generally very much as it was outlined in 1930. The change in furnace dimensions would be very slight and of no especial significance, except with respect to changes in stock-line diameter, of which more will be said hereafter. The high-efficiency stove as developed by various designers is thoroughly described within this report, and few changes have taken place since. Blowing equipment shows refinement and reflects the improvement in steam engineering. Hoisting and charging equipment and ladles for the conveyance of iron and slag remain, in general, as they were in 1930. In accordance with a general tendency

Jan 1, 1935

By Walter E. Hopper

The Caddo oil-field, shown in Fig. 1, is located in Caddo parish, northwestern Louisiana. The known producing territory of oil is covered by townships 19 N, 20 N, 21 N, 22 N, and ranges 15 and 16 W., shown in Fig. 2. The center of the field may be taken as Oil City, 24 miles north of Shreveport, on the Kansas City Southern railway. Shreveport is the second largest city in the State, and is the connecting point of five railroad-lines. Drilling at the present time, however, is going on all over northern Louisiana, especially in Caddo and the neighboring parishes. During the winter of 1908-09 I spent 'four months in the Caddo field, under the direction of the Louisiana Geological Survey and the U. S. Geological Survey. II. History and Development. Natural gas escaping at the surface is found at numerous places in northwestern Louisiana. At Shreveport, the plant of the Shreveport Ice & Refrigerating Co. has been lighted by natural gas for 20 years. The well was drilled for water, but was abandoned on account of the gas. A test well, put down in 1905 near the western limits of Shreveport, was driven to 1,650 ft., and encountered indications of gas and oil at various depths, but did not succeed in finding enough to be profitable. Attention was first attracted to the Caddo field in 1895 by indications in water-wells from 40 to 60 ft. deep, in which the pressure of natural gas was noticeable. This indication of gas in a shallow well led to the drilling of the first well in the Caddo field, the old Savage Brothers & Morricell, or the Caddo Lake Oil and Pipe Line No. 1. The rig for this well was erected in May, 1904, and drilling began in June, 1904. The well was bailed Mar. 23, 1905, with a small amount of oil. It was deepened July, 1905, and converted into a "gasser" Jan. 3, 1906. It was abandoned January, 1907. In consequence of the finding of oil in the Savage well, drilling-operations were pushed with energy; and in April, 1905,

Jan 1, 1912

By Raymond E. Birch, Oscar M. Wicken

THE mineral magnesite, formerly the source of nearly all magnesia, now shares this role with brucite, dolomite, and the world's natural and artificial brines. The mineral magnesite is the normal carbonate of magnesium, MgCO3, composed when pure of 47.6 pct MgO and 52.4 pct CO2. It is one of the calcite (CaCO3) group of rhombohedra1 car- bonates, which also includes dolomite, CaCO3.MgCO3, and siderite, FeCO3. Magnesite does not form an isomorphous series with calcite or dolomite; consequently, these lime-bearing carbonates commonly present in magnesite deposits are there only as mechanical mixtures. Magnesite and iron carbonates form a continuous isomorphous series and therefore are inseparable mechanically. The variety of magnesite known as breunnerite is an isomorphous mixture of iron and magnesium carbonates. Magnesite may be either crystalline or amorphous (cryptocrystalline). The former, which includes breunnerite, is often termed spathic magnesite. Crystalline magnesite varies from finely to coarsely crystal- line in texture and has a hardness of 3.5 to 4. The color is white, yellowish, blue-gray to drab, red, pink, black, or mottled. It is seldom found pure but usually contains variable amounts of iron, lime, silica, and sometimes manganese. The color cannot be used as an index of purity. The cryptocrystalline variety is perhaps the more common type but the crystalline variety usually occurs in larger deposits. The amorphous type is fine grained and compact, showing no cleavage. It is usually snow white but sometimes is light to pale orange yellow or buff, owing to impurities. The fracture is conchoidal to uneven and the hardness 3.5 to 5. Silica may be present as inclusions of serpentine, quartz, chalcedony, or other minerals. The lime and iron contents are usually low. In general, amorphous magnesite is somewhat purer than the crystalline variety. The specific gravity of cryptocrystalline magnesite is 2.90 to 3.00. Pure crystalline magnesite has shown a specific gravity of 3.02 but iron

Jan 1, 1949

Book Review MEXICO UNDER CARRANZA. By Thomas E. Gibbon, Los Angeles, California. Doubleday Page and Co., New York, 1919, 270 pp., 711/2 X 5 in. $1.50. A vivid, accurate, convincing summing up of the Mexican problem as it confronts us today, devoid of sensationalism or bigotry. A compelling narrative of the relations of the Carranza Government and our own from Oct. 15, 1915, when it was recognized as the de facto government of Mexico, to the present time. It shows the absolute lack of promises kept or lived up to either with its own people or the United States. This is not done by invective or the indiscriminate use of adjectives but by quoting from the instruments on record on both sides of the case. The driving of the Red Cross out of Mexico, which condemned many of the native peons to starvation, and the interference with the Pershing Punitive Expedition are merely mentioned, but the crying crime against the Mexican people, who have sunk to unbelievable depths of misery obscured, but not exceeded, by the sufferings in Europe, is held up in a clarified light. Two illuminating chapters are devoted to the character and treatment of foreign investments in Mexico, Which are a complete refutation of the common statement that Mexico has been exploited remorselessly by the foreign investor. The conces-sions given by Diaz in the days of his regime most condemned are nowise as large nor the land grants as extensive nor the title so absolute as those granted to the railroad builders of our own transcontinental systems and other of our nationally subsidized works. This is not left to further argument but is settled by quoting the various official instruments and not at all in a tedious way. The author's concluding chapter is a picture of the Mexican people from Aztec times, when they had reached a civilization which gave them a better calendar than the Roman Empire ever had until modern times, to their present unhappy and pitiful condition. He concludes, basing his findings on parallel historical downfalls of a once proud people, that present conditions are the natural result of the absolute domination of an alien minority. He grants, of course, that there are many estimable Latin-Mexicans of integrity, ability and charm, but maintains that the dominant minority has continually degraded in fulfillment of the sociological law that the sure revenge of the servile class is found in the corruption of the master class. The book is replete with historical and literary allusions which, added to the pleasing style of the accomplished author, make fascinating the account of one of the world's great tragedies. Mr. Gibbon is a lawyer who has spent much time in Mexico and shows an understanding of the native people not shared by all writers on the Mexican problem. A distinct addition to all literature on the subject. P. E. B.

Jan 8, 1919