Search Documents

By E. R. Johnson

THE copper concentrator of the Braden Copper Co. is at Sewell, Chile, on the western flank of the main Cordillera of the Andes, at an air distance of approximately 50 miles southeast of Santiago, the capital of Chile. The region is mountainous and space is at a premium because of the rough terrain and the danger of snowslides. The ore, a porphyry copper, is mined by a block-caving method in the El Teniente mine. It is hauled to the crushing plant, a distance of 2.6 miles, through a tunnel because of the severe climatic conditions. The usual large, coarsely set, primary reduction machines found in many ore-treating plants are not required because of the mining method employed and the limiting 12-in. spacing of the grizzlies at the head of each ore pass in the mine. It is the purpose of this paper to describe the numerous improvements made in the crushing section of this large flotation concentrator during the past 15 years to increase the efficiency of the plant and to raise the daily output from around 20,000 to 30,000 tons. The reader should keep in mind that all changes were made within the existing building because of the limited space and the high cost of the heavy mill construction required to withstand the snow loads. The present plant, as well as the former, operates on a 24-hr, 7 days a week basis. FORMER PLANT The crushing plant commenced operations at its present site in 1921, the main equipment being No. 7 1/2 gyratories, followed by 48-in. horizontal Symons disk crushers. Fines were removed by 1-in. stationary grizzlies ahead of each unit. In 1924 a third stage of crushing was provided by the addition of 55 1/2-in. rolls in open circuit. During 1925, the Symons disks were replaced by 73 1/2-in. rolls. All the rolls were changed to closed circuit, with elevators and screens to give a final product of 9 pct plus 3-mesh. The flowsheet of a typical crushing section of this period is shown in Fig I. The ore was withdrawn from a common bin serving the five crushing sections in the plant by means of any number up to six 36-in. wide-apron feeders, which discharged onto a common conveyor belt. This conveyor was equipped with a magnetic head pulley and the crusher attendant was stationed near the discharge end to pick out pieces of mine timber that might be in the ore. The ore was discharged over a 1 3/4-in. spaced bar grizzly and the oversize of this grizzly was crushed by a No. 7 1/2 McCully gyratory crusher set at 1 3/4-in. opening on the closed side. The grizzly undersize joined the gyratory discharge and was conveyed to a set of 73 1/2 by 20-in. Garfield rolls set at I in. These rolls operated in closed circuit with a bucket elevator and two vibrating screens placed in parallel.

Jan 1, 1947

By William L. Saunders

MANY members of the Institute, who participated in the visit made, during the Bethlehem meeting of February, 1906, to the shops of the Ingersoll-Rand Company, at Phillipsburg, N. J., inspected with interest the new Electric-Air drill, which the company had set up for the purpose of showing it in actual operation to American. mining engineers. At the request of the Secretary of the Institute, I promised at that time to prepare a paper for our Transactions, describing the construction and advantages of the machine. But such a paper would then necessarily have contained much that was only expected or claimed by the designers and manufacturers of the drill, and not yet incontrovertibly proved by varied and long-continued practice. However moderate such statements might have been, they would have given inevitably to the paper, to some extent at least, the air of a prospectus, rather than of a technical contribution. I therefore decided, with the Secretary's approval, to postpone the writing of the promised paper until it could set forth the results of adequate actual practice, as well as the latest details of construction, etc., based upon practical experience. That period has now arrived. The Electric-Air drill has been exhaustively tested in the field, under varied and arduous conditions and upon the hardest rocks. It is now fairly in the field; its merits and performances are matters of unimpeachable record, and its place among established competitors can be definitely determined. As a representative of the Ingersoll-Rand Co., as well as a member of the Institute, I may be permitted to add that my company, being largely interested in the manufacture of air-

Jan 9, 1907

By T. L. Joseph

THE invention of the Bessemer converter process in 1856 added great impetus to the manufacture of steel and is one of the outstanding contributions to process metallurgy. Although the process of refining pig iron by passing air through the molten metal bears the name of Henry Bessemer, it should be mentioned in passing that William Kelley of Eddysville, Ky., worked on the process as early as 1847. Kelley was granted a patent on the process in 1857, inasmuch as he was able to prove priority in discovery.1 After considerable litigation in 1865 the respective interests of Kelley and Bessemer were combined. On Sept. 10, 1856, Robert Mushet of England obtained his first patent on the application of manganese to cast steel. Mushet anticipated trouble in purifying iron by passing currents of air through it. His patent specified that steel made in this way often contained flaws and was red short or cold short. Mushet understood the refining of pig iron into steel well enough to realize the difficulties likely to be encountered from oxidation of the iron. Mushet was not only an inventor but he was also an investigator. He understood the principle of selective oxidation which takes place in the converter process, arid he realized therefore that the remedy for over-oxidation was attainable if a suitable metal could be found at a reasonable cost and in sufficient quantities. His first experiments were made in small crucibles holding a few ounces of metal. Later his work was conducted on a larger scale and with complete success. Manganese had been used in making steel a quarter of a century before the converter

Jan 5, 1927

By C. W. Davis, L. R. Messer

THE name fuller's earth, which was derived from its early use in "fulling" or removing grease from woolen goods, is a term that is generally considered to designate mineral matter, containing hydrous aluminum silicates of the clay group, which has a high capacity for removing colors from oils, whether of animal, vegetable, or mineral origin. Fuller's earths are usually dried and may be "tempered" by heating or may be treated with water or reagents to improve their efficiency. For our purpose the term "acid-treated earths" will include those products from the partial decomposition of mineral water by acid which are equal to or more efficient than an untreated fuller's earth from Quincy, Fla., when used in bleaching mineral oil by the "contact" process. In general, the contact process for treating oils consists of heating and agitating a mixture of oil and finely divided adsorbent, the latter being subsequently removed by filtration. The term "adsorbent" is used because, although there has been a great deal of controversy over the mechanism of removal of impurities from oils by mineral matter, there is no doubt that adsorption, which involves the surface of the solid, plays a major part.' The properties that make fuller's earth useful in the treatment of petroleum products by "percolation1' and in the purification of edible oils by the contact process have long been studied, but the comparatively recent adaptation of the contact process to the bleaching of petroleum products has made desirable the further investigation of fuller's earth and other adsorbent earths.

Jan 1, 1929

By Joseph Newton

MUCH the same story can be told about the copper industry for the year 1944 as for the three preceding years. Operators report few or no technical changes at their plants and the main endeavor has been to maintain high production with existing equipment. No large new installations have been made to increase plant capacities and apparently over-all copper production has passed its maximum. The present decline in copper production results partly from the severe labor shortage. As is true of most industries; the outstanding fact about the copper industry during the past few years has been its tremendous and sustained production which has been maintained in spite of serious shortages in material. labor, and technical personnel. The figures in Table I give a concrete example of how production has been increased at one large smelter in the United States-the Garfield plant of the American Smelting and Refining Co. at Garfield. Utah. These figures, reported by W. G. Rouillard. superintendent. give the production of the Garfield plant for the five years 1940-44 inclusive. The total blister production

Jan 1, 1945

By Woolf, W. G.

Filtration of hot (60°C) supersaturated zinc sulphate solution (sp gr 1.540) from slimy leach residues at the electrolytic zinc plant of Sullivan Mining Co., Kellogg, Idaho, is de- scribed. Separation of liquids and solids in the finished leach is by Burt filters modified to meet conditions of high-acid, high-density process for electrolytic zinc. Operating characteristics of the Burt filter on this pulp are presented.

Jan 1, 1950

By W. F., Dietrich

THIS paper deals with the- methods of mining the high-grade clays of California. Although the majority of the clay pits in the state are operated on a scale that is small by comparison with most metal mines, this very fact results in a diversity of methods and gives rise to problems of selection of the method best suited to given conditions. Two or three operators in California produce approximately 500 tons per day of a single kind of clay from a single pit. About five varieties of clay are mined on a scale of 200 to 400 tons per day; not over fifteen varieties are mined on a? scale of 50 to 200 tons per day; and more than 50 varieties are mined at a rate of less than 50 tons per day. It is the aim of this paper to delimit, insofar as the data at hand permit, the conditions and scale of operations that favor the selection of each dominant method of mining that is actually being applied at California properties. Details of the occurrence and utilization of the clays of California have been given in a recent bulletin and are not considered here.

Sep 1, 1928

By H. H. Stout

IN the early fall of 1925, the writer was conducting, in the Ledoux and Co. labora-tory, New York, experiments directed to-ward ascertaining the effect on its impurity content when cathode copper was subjected to a current of various gases at an elevated temperature below the melting point, The apparatus consisted of a vertical 1-in. dia. silica tube about 12 in. long, heated on the outside, The cathodes were broken to pass a8-in. mesh, and a current of various differ-ent gases was passed up through a 4-in, long column of these loose cathode particles in the vertical tube furnace. Temperature was maintained to i500° to 1600°F. and the gas treatments lasted from 3 to 6 hr, The writer observed that whenever reducing gas (H2 or CO) was used, these cathode par-ticles stuck together at points of contact with each other. The cohesion was so marked and tenacious that an examination was made of the fractured surfaces, when cathode particles were broken from the cluster. Crystal growth was always found to have taken place across the surfaces where separate particles were in contact, but only after all oxides, sulphates, etc, had been completely removed. The idea of a possible new process was then conceived and was disclosed to A. M. Smoot (V. P. Ledoux and Co.) with intent to obtain his views. The first conception as given Smoot was "to gas-clean broken cathodes, put them in an extrusion press, solidify and extrude them at around 1500°F," Smoot's reaction, after a few moments considera-tion, was, "It looks perfectly all right to me."

Jan 1, 1940

By G. B. Kasik, George Sachs, George Espey

IT has been reported frequently that the hardness and strength vary over the cross section of cold-worked, particularly cold-drawn, material. Brass rod and wire usually has been found to possess a maximum strength and hardness near the surface.1,2 According to Sachs,1 the center fiber has about the same strength as a wire stretched by the same amount in a tensile-test machine, the strength increasing toward the surface (Fig. I). These differences are particularly large for wire given a small reduction on drawing through a die with a wide opening. However, with increasing reduction and hardness, a tendency to form a thin soft surface skin becomes apparent. On the contrary, copper wire has usually been found to possess a soft surface skin" and it has been reported by Harris3 that during the cold-drawing of hot-rolled wire the surface layer becomes increasingly softer than the core, while the layer of maximum strength moves toward the core, it being found near the surface at first. The increase of strength and hardness from the core to the skin is readily explained by the observation that, in addition to the stretching, the layers of a rod or wire are sheared more the closer they are to the surface.1,6-8 However, the presence of a soft surface layer can be attributed only to an annealing effect. The source of such a softening might be the extremely high temperature that originates from the friction between [ ]

Jan 1, 1941

By T. M. Olson, B. G. Lewis

The adsorption of selenite on bentonite, kaolinite, and an iron--coated illite was studied to determine the importance of several soil variables on selenite removal from uranium mill tailings pond seepage. Adsorption capacities of the clays of selenite varied by orders of magnitude and decreased in the following order: illite > kaolinite > bentonite. Maximum adsorption of selenite on the clays was observed between pH 2.5 and the clay's zero-point-of-charge. Substantially less selenite was adsorbed on these clays in actual mill tailings solutions than in model systems. Virtually all selenite was removed from the tailings at pH 7. The principal removal mechanism at this pH is suggested to be the adsorption of selenite on freshly precipitated metal hydroxides. It is concluded that selenite can be removed from tailings seepage in soil or in clay liners in the presence of kaolinitic clays and iron oxides. Selenite would also tend to be removed from tailings seepage in calcareous strata.

Jan 1, 1984

By W. M. Albrecht, W. D. Klopp, R. I. Jaffee, B. G. Koehl

Kinetic studies were made of the reactions of tantalum with oxygen, nitrogen, and air at 400o to 1500°C. The tantalum-oxygen reaction is linear from 500° to 1250°C. The tantalum-nitrogen reaction follows a cubic rate law at 400° to 700°C and a parabolic rate law at 800" to 1475°C. The reaction behavior in air is initially parabolic followed by a transition to linear behavior. In the search for high-temperature materials, considerable interest is being shown in the refractory metal, tantalum. It is the third highest melting metal with a melting point of 2996°C. Also, tantalum has excellent ductility, making it one of the most workable refractory metals. In considering high-temperature applications of tantalum, the oxidation kinetics of the metal must be known. Such information also serves as a basis for the development of corrosion resistant tantalum-base alloys. Therefore, this study was made to investigate the reaction of tantalum with air, nitrogen, and oxygen. LITERATURE Several oxides of tantalum have been reported. The pentoxide, Taz05, is the only oxide of tantalum whose identity has been established. A high-temperature modification, aTa2Os, has been reported by several investigators.1-4 A low-temperature phase, ßTa2O5, undergoes an allotropic transformation at 1320o to 1350oC. 5-8 Four other oxides of tantalum have been reported. The oxides TaO2, TaO, and Ta4O have been reported by schonberg.9 A suboxide Ta2O, was observed by Wasilewski 6. However, the presence of oxides lower than Ta2O5 is questioned by Lagergren and Magneli.7 In oxidation studies, vermilyeal0 and Peterson, et al.,12 reported one possible phase intermediate between Ta and Ta2O5. Only Ta2O5 was formed in the tantalum air reaction, as reported by Michae1.l3 Several studies have been made on the kinetics of the tantalum-oxygen reaction. vermilyeal4 investigated the range 50° to 300°C and found that the rate of growth of a thin adherent oxide film could be described by the Cabrera-Mott theory. Gulbransen and Andrew15,18 studied the reaction kinetics of tantalum in oxygen pressure of 1/10 atm at 250° to 450°C. At all temperatures the reaction followed the parabolic rate law for periods up to two hours. The oxidation behavior in the range 500" to 1000°C was found to be linear at oxygen pressures of 0.2 to 600 psi according to Peterson. et al.l1 At very low pressures (1 x 10-3 to 2 X lo-' mm of Hg) Gebhardt and seghezzi17 reported linear oxidation at 800° to 1500°C. The reaction of tantalum with air is similar to the reaction with oxygen. Studies have been made by Waber, et a1.,12 and Michae1.l3 Two nitrides of tantalum, TaN and Ta2N are known. Their structures have been determined by Brauer and Zapp 18,19 The tantalum-nitrogen reaction kinetics have been investigated by Gulbransen and Andrews. 15, 16 The reaction follows the parabolic rate law at 500° to 850°C at a nitrogen pressure of 1/10 ,atm. At the same temperature, the tantalum-nitrogen reaction is much slower than the tantalum-oxygen reaction. EXPERIMENTAL TECHNIQUES Material— The material used in this study was high-purity, electron-beam-melted tantalum obtained from the Temescal Metallurgical Corp. The hardness of the as received ingot was 76 Vhn. The analysis of the material is given in Table I. Methods—Cylindrical specimens of tantalum approximately 0.9 cm in diam and 0.5 cm in length

Jan 1, 1962

By E. S. Davenport

WHEN annealed carbon, or low-alloy, steels are suitably heated the ferrite (alpha iron solid solution) and the carbide, of which they are composed, react together to form a single solid solution of carbon (and other elements) in gamma iron (austenite). This reaction may begin only at a certain minimum temperature called the eutectoid temperature. The first ferrite and carbide thus to react together do so in definite proportions known as the eutectoid composition. With further heating the original constituent that is present in excess is dissolved in the austenite until exhausted. Whether the excess constituent be ferrite (hypoeutectoid steels) or carbide (hypereutectoid steels) the procedure is much the same, and upon slow cooling the homogeneous austenite expels the excess of either (proeutectoid ferrite or carbide) until the eutectoid composition is reached. Thus the reaction upon heating is strictly reversed upon cooling and accordingly an equilibrium diagram of this process may be constructed. Such an equilibrium diagram concerns itself only with the tempera¬tures involved and with the proportions and compositions of the phases developed under conditions that suffice to permit equilibrium. Specifically it has no concern for the type or mode of distribution of these constituents nor with any extra-equilibrium conditions such as undercooling, which is almost universally encountered in metals. Actually, however, of great importance is the sluggishness toward equilibration caused by the not inconsiderable time involved in diffusion. Thus instead of the theoretical transformation point AE, we find for a certain rate of heating or cooling the use of the designations Ar and Ac (transformation temperature found on cooling and upon heating). These figures obviously have no particular meaning except as measured and expressed for a definite heating or cooling rate, and represent the apparent temperature displacement caused by an inadequate time allowance. In this paper are presented the results of a study of the time required for' the transformation of austenite to ferrite and carbide at a variety of temperatures and also of the time required for the reaction austenite ?martensite at the temperatures at which this reaction occurs instead of

Jan 1, 1930

By V. H. Wilhelm

WITH rapidly diminishing oil reserves: a great percentage of which are uneconomical at present prices, some of the existing methods of development and production will have to undergo radical re- visions to meet the changes continually taking place in the petroleum industry. Imagination in an engineer is a great asset. The fancy of today is found to be the realization of tomorrow, and with this thought in mind, there is here presented a more or less imaginative picture which, to my mind, has a meritorious basis. Directed drilling has reached a stage of accuracy sufficient to allow the prediction that this art will be used in the future development of oil structures, especially those \\,it11 thin sand bodies 'and steep dips. Directional drilling in a number of fields in California has gratifying results. Wells which practically laid pipe lines through the oil sands have enjoyed a greater drainage radius with a consequent greater initial and cumulative production. In one field where the vertical thickness of sands was approximately 550 ft., wells drifting at an angle as great as 55 deg. fro111 vertical had over 1100 ft. of perforated pipe in contact with these sands. These wells were, and are, remarkable for their great initial pro-

Jan 1, 1936

By Charles R. Keyes

I. INTRODUCTION. FOR a period of several years, and in a large number of cases, the Metallurgical Laboratories of the New Mexico School of Mines were employed in umpire work. During this time many important local problems were solved. Against the results of careful chemical analyses of ores, assay-returns were often checked. In many cases the assay-methods of mine and custom-smelter were compared, and both often found faulty for the ore concerned. A wide range of ores was covered. Many of the chemical analyses and assays were made by Dr. F. C. Lincoln, Professor of Metallurgy, now of the Montana State School of Mines. A varied series of instructive assays was prepared by Prof. R. B. Brinsmade, now of the West Virginia State University. Single assays and given series of tests were undertaken by H. T. Goodjohn, now chief chemist to the Cia. Metalurgica de Torreon, Coahuila, Mexico; by H. J. Hubbard, now superintendent of the Butters Divisadero Mines, Jocoro,. San Salvador, C. A.; by E. D. Morton, now superintendent of the Arizona & Nevada Copper Mining Co., at Lunning, Nev. ; and by A. W. Edelen, now superintendent of the Angangueo Unit of the American Smelting & Refining Co., in Michoacan, Mexico. A critical comparison of assay-methods that were found to be followed in the case of certain gouge-ores mined in the Mimbres range in New Mexico, and about which there had been much controversy, was made by D. F. Riddell, then Acting Professor of Assaying, and now superintendent of the Providentia Mines Co. of Parral, in Chihuahua, Mexico. To him is due the credit of much that is contained in the following notes, which be has generously permitted -to be used in advance of the publication of the complete results.

Jul 1, 1911

The Library of the above-named Societies is open from 9 A.M. to 10 P.M., except on holidays. It contains about 70,000 volumes and 90,000 pamphlets, including sets of technical periodicals and the publications of scientific and technical societies. Members of the Institute, with few exceptions, are forced to spend a portion of their time in localities isolated from sources of information. To these the Library, through its Library Service Bureau, can render valuable service through correspondence; letters requesting information will receive especial attention. The Library is prepared to furnish references and photographic copies of articles on mining and metallurgical subjects; to determine the existence of mining maps, and to furnish general information on the geology and mineral resources of all countries. All communications should be made as definite as possible so that the information received may be what is desired and not include collateral matter which may not be of interest. The time spent in searching for such collateral matter will be saved, and the information will be sent more promptly and in more usable shape.

Jan 7, 1917

By Robert Anderson

ROUGHLY, a crack in a casting may be considered, for the moment, to be due to fracture of the alloy resulting from the stress set up by the contraction in volume on passing from the liquid to the solid state. Cracks may be external or surface, internal or deep-seated, or incipient or so-called strain cracks. Draws may appear as depressions, unevenness, and "pinching in" of the surface of a casting. Roughly, draws are due to contraction in volume and are governed largely by the same factors as cracks. A casting may be cracked, however, without being drawn. Shrinkage is a foundry term; it connotes the contraction in volume of a metal or alloy on passing from the liquid to the solid state. Pattern-makers' shrinkage is the total contraction in volume (including liquid, solidification, and solid shrinkage) that occurs when an alloy is poured into a mold. The contraction in volume of aluminum is one of the principal factors affecting the occurrence of cracks, as will be shown later, and the question of shrinkage and its control requires careful study in any treatment of cracking in castings. In the case of, sand and die castings, cracks have been attributed to a number of causes, but in the case of most light aluminum alloys, they are due to the large contraction in volume on freezing and the lack of its regulation or control. The most important factors are: (1) Contraction in volume; (2) composition of alloy; (3) quality of melting charge; (4) design of casting; (5) method of molding; (6) hardness of ramming; (7) method of gating; (8) hardness and characteristics of cores; (9) chills; (10) risers; (11) melting temperatures; (12) furnace used for melting; (13) pouring tempera-tures; (14) inclusions in alloys; (15) hot shortness of alloys; and (16) physical properties of alloys at high temperatures. Of these, the first, second, third, and eleventh to sixteenth involve ascertainable metallurgical facts; the remainder are largely matters of opinion, judgment and technical knowledge of men experienced in the production of castings.

Jan 10, 1921

By R. D. Parks

DESPITE the handicap of reduced production in many districts, the mining industry in 1938 forged steadily ahead toward solution of its minor technical problems and has of-defected major advances in several fields. In California hydraulic mining for gold, shut down for forty years, will shortly be resumed following revision of restrictive laws. Disposal of hydraulicked ground is to be regulated by settling dams so as not to interfere with agriculture. Gold mining has been aided also by the development of a new high-efficiency dry amalgamator which applies the Ramsay mercury separator to the original de Phily process. Based on the principle that crushed ore will follow a rod into a mercury bath, this simple device is primarily adapted to dry areas and is to be available in small, multiple units suitable

Jan 1, 1939

By Francis L. Bosqui

The following paper embodies a report which I made on the filter-press treatment of slimes at the Liberty Bell mine, Telluride, Colo. At the time this report was submitted, the management deemed it wiser to defer the installation of so costly a plant as the one required, in the hope that some of the many investigators in the field might soon evolve a cheaper and more perfect method of slimes-treatment, and one better suited to the conditions at Telluride. The Liberty Bell ore consists essentially of quartz and clay, with iron pyrites disseminated through the quartz in very fine particles. There is considerable iron and manganese stain in some of the ore, the latter especially in the clays, which are sometimes quite black. Occasionally particles of galena, zincblende, gray copper and a few other minerals are seen, but they are comparatively rare, and not in sufficient quantity to affect considerations of treatment. Free gold is occasionally seen in the quartz, and one or two instances of mire silver have been observed. The milling-plant consists of an 80-stamp amalgamating mill which crushes through 20-mesh screens; 20 Wilfley concentrating tables, taking out, in iron sulphides, about 2 per cent. of the total ore crushed; and a cyanide plant consisting of two tiers of 33 ft. vats, five in each tier, fed by revolving pipe-die tributers. The slimes overflow from the upper settling tanks through gates with adjustable outlets, and thence to a large canvas-plant, which efects only a small saving. This slimes product, of which about 100 tons escape per day (or 38 per cent. of the total ore crushed), contains about 3 per cent. of dry solids. Of this approximately 93 per cent. will pass a 200-mesh screen. The slimes range in value between $3.90 and $4.87 per ton, the values being about equally distributed between gold and silver. The actual averages for ore and slimes during the years 1900-

Jan 1, 1904

By H. H. Hausner, S. Storchheim, J. L. Zambrow

The solid state bonding of aluminum to nickel was studied as a function of temperature, pressure, and time at pressure. The initial results indicated that as the reaction conditions were varied, marked changes in tensile strength occurred. Plots of the log penetration coefficient vs the reciprocal of absolute temperature for various isobars were straight lines displaced from each other. THE techniques of bonding different metals to A each other include brazing, welding, welding by application of a molten phase, and solid state welding without any molten phase present. This last technique, the pressing of metals either at room temperature or at some temperature below the melting point of the metals to be joined, seems to offer interesting possibilities for bonding purposes. However, this technique has not been completely investigated, and very little is known about the diffusion phenomena which occur during solid state welding. Some previous work on the effect of pressure on diffusion1 was inconclusive. This paper is concerned with an investigation regarding the effect that the processing variables, such as pressure, temperature, and time at pressure, have in solid state bonding. The tests were made with aluminum and nickel and special emphasis was given to the strength of the bond between these two metals and to the intermetallic penetration rate during the bonding process. It seems that the effect of pressure on the intermetallic penetration is of particular importance for practical purposes and this effect was therefore studied in detail. Procedure Apparatus: The means of solid state bonding used for this study was that of the hot-pressing technique. This method requires the equipment pictured in Fig. 1 and involved the following procedure. The two metals to be bonded were placed in an aquadag lubricated 18-4-1 tool steel die, 16 in. high by 1.440 in. ID, between punches of 1.366 in. diameter made of the same material. A thermocouple

Jan 1, 1955

By J. W. Stewart

THE aim of this paper is to point out the various ways in which design is taught in standard four-year mining engineering curricula in American colleges and universities; to discuss the reasons apparently justifying the great diversity of procedure that exists along this line; and to indicate possible solutions to the difficulties now attending the teaching of design. A study was made of typical four-year mining engineering curricula in 15 colleges and universities of the United States (Table I). Great diversity in content of the various design courses, if taught as described, became apparent immediately. It appeared that it might be both interesting and instructive if the cause for this colorful variety could be found. Was the cause local mining conditions, departmental individuality, or actual necessity? Study of the school catalogues revealed that the various design courses could be classified into two fairly distinct types; namely, (I) those dealing with mine equipment or structures, and (2) those dealing with underground layout of mine workings. It seemed reasonable to label the first type of course "mining design" and the second type "mine design." Some such distinction must have been in the minds of mining educators, for we find both names (i.e., mine design and mining design) used to designate the design courses included in the various mining curricula. Unhappily, the name and the apparent content of such courses do not, in all instances, conform to the classification made here, although in most instances such conformation does obtain (Table I), It is possible that in the exceptional case the method of teaching a design course, and consequently the content of it, may have been changed at some time without change in the name of the course. Apparently only 3 of the I5 schools made an effort to cover both types of design in their curricula (Table I). Two other schools did not list or describe any course of study that could with certainty be taken as a design course. Of the remaining 10 schools, 9 gave a mining-design type of course and one gave a strictly mine-design type. Obviously, the preponderance of design courses afforded are of the mining-design type. Why? To answer this question, it is necessary to make a study of the prerequisites for the two types of design courses taught. In all schools the design courses were taught in the senior year; in eight, design was taught throughout both semesters; in two, it was taught during the first semester only; and in three it was taught during the second semester only. Consequently, excepting the last three cases noted, it is obvious that all prerequisites for a design course should be completed by the end of the junior year. PREREQUISITES What are the probable prerequisites for the different kinds of design courses as they appear to be taught? Let us take first the case of the mine-design type of course, having to do with layout of underground workings. Here it would seem that logical

Jan 1, 1941