Search Documents

By E. P. JENNINQS

(Cleveland meeting, October, 1912.) LARGE deposits of titaniferous iron-ore occur at Caribou, an old silver-mining camp in Boulder county, Colo., 17 miles west by south of Boulder, and a few miles northwest of the tungsten-mines. Professor Regis Chauvenet 1 published a part analysis of the ore many years ago, but gave no description of the wall-rock. Caribou hill, which contains both the silver-bearing veins and the iron-ore deposits, is a low dome of gabbro surrounded by the Archaean schists and gneisses of the Front range of the Rocky mountains, the peaks of which, a few miles west of Caribou, attain an elevation exceeding 12,000 ft. The gabbro stock is roughly elliptical in outline, with approximate diameters of 1 and 3 miles. The crest of the dome is 10,500 ft. above sea-level, and the town and ore-deposits are 500 ft. lower. Outcrops of the iron-ore occur in the town and extend NW. for 2,000 ft., where they disappear under the swampy meadows of Caribou park. Portions of the deposit are covered by drift, but one continuous outcrop is 900 ft. long and from 200 to 250 ft. wide. A second deposit is 0.25 mile south of the town along the eastern slope of the hill. It is not as well defined as the north bed, but is approximately 1,000 ft. long and from 100 to 200 ft. wide. The easily disintegrated ore does not form prominent outcrops, but the outlines of the deposits are readily traced by the large amount of ore fragments that cover the ground. Trenches and pits sunk on the outcrop expose a roughly banded magnetic iron-ore, with pyroxene as the principal gangue-mineral. The Gabbro. This rock was classified in the field as a gabbro from the presence of pyroxene and striated feldspars, and for convenience the field-name will be retained. 1 Chauvenet, Regis, Biennial Report of State School of Mines, Golden, Colo., p. 16 (1886).

Oct 1, 1912

By Ralph W. Marsden

The natural iron ores of the Lake Superior Region in the United States are being replaced by iron-ore concentrates produced from magnetite- or hematite-rich horizons in the Precambrian cherty iron formations. The production of natural ores will soon be less than one-half of the total ore shipped annually. The tonnage of natural ore produced will continue to decline until it is a minor percentage of the ore shipped. The natural ores include (1) soft ore, (2) hard ore, ( 3) conglomerate ore and ( 4) siliceous ore. The soft ores are the important ore type and are sometimes termed "Lake Superior type ore". These ores are in situ deposits of hematite and limonite formed by the leaching of silica and other gangue materials in the iron formations. The leaching is believed to have been done by downward moving surface waters. In deep ore deposits, generally over 1000 feet below the present surface, circulation and leaching action may have been assisted by hydrothermal activity. Hard ore deposits occur on the Vermilion and Marquette ranges where hematite or magnetite has replaced the silica (and possibly some silicates) in cherty iron formation. These ores commonly occur in structural situations favorable for the movement of hydrothermal waters. The ores are believed to be the result of hydrothermal action with iron, possibly from the iron formation, transported by hydrothermal waters to areas favorable for the replacement of silica by iron oxides. Certain stratigraphic horizons of the Lake Superior Precambrian cherty iron formations contain sufficient iron as magnetite or hematite, with a grain size and texture that will give adequate mineral liberation, to yield an ore-quality product after grinding and concentration. The magnetite-rich deposits are termed magnetite taconites. These ores occur on the Mesabi, Gogebic, and Marquette ranges. Magnetite taconite ores are unenriched cherty iron formation and are the result of the sedimentary deposition of the iron formation and the metamorphic history of the rock. The commercial quality hematite-rich iron formations in Michigan are termed jasper ores. The jasper ores are being mined on the Marquette and Menominee ranges. These ores are composed of specular or granular hematite associated with quartz and iron silicates. The jasper ores appear to be recrystallized iron formations in which iron, prior to recrystallization, occurred as hematite.

Jan 1, 1968

By Thomas L. Kesler

I all of the 14 million tons of kaolin produced in Georgia through 1949 had been mined from a single deposit 20 ft thick, it would represent a mined-out area of less than 1 sq mile. This measure of depletion is in such strong contrast with the large size of the area shown in Fig. 1, from which most of the output has come, that there has developed an optimistic outlook concerning future supplies of kaolin equal in grade to that already mined. Dozens of mines are widely but not evenly distributed within this area, which consists mostly of parts of Twiggs, Wilkinson, and Washington counties. There are scarcely half a dozen kaolin mines elsewhere in the state that have been appreciably productive, although the areas in which they occur may have good possibilities. Most of the efforts to find new deposits, therefore, will be confined to the area shown in Fig. 1, for it is here that the industry has established its facilities, and prospecting is encouraged by relatively numerous outcrops and opened deposits of kaolin. The Ocmulgee and Oconee rivers drain the area. They and their main tributaries have flat, swampy floodplains covered with alluvium and for the most part thickly wooded. The divides between these streams are intricately dissected by the minor tributaries, which are spring-fed in steep-walled, cirque-like heads. Gullying and under-cutting are active along the streams but are partly controlled by unusually dense vegetation. The mean altitude is about 350 ft above sea level, and locally the relief ranges up to 200 ft. The area is near the inner margin of the Coastal Plain, and is underlain by Cretaceous and Tertiary formations. Its general location is shown in black in Fig. 1. The division between the Coastal Plain and the Piedmont plateau is actually a very sinuous line, the fall line, marking the extent to which erosion has stripped the Coastal Plain sediments from the southeastward-sloping surface of the crystalline rocks of the Piedmont. Cretaceous Host Formation The kaolin deposits, which are described in the succeeding section, occur sporadically in lenslike bodies in a thick series of poorly sorted clayey sands constituting the lowermost of the Upper Cretaceous formations, the Tuscaloosa. The basis for this correlation has been reviewed by Cooke.1 The same formation has been termed the Potomac group by Ladd2 and the Middendorf formation by Smith' in reports on the kaolin deposits. In another report, Veatch4 called the formation the Tuscaloosa but correlated it with the Lower Cretaceous. The Tuscaloosa in this area consists of fine to very coarse sands, commonly cross-bedded, which contain widely different proportions of white, pink, and yellow kaolin and considerable white mica. A few of the coarser beds contain quartz grains up to 3 in. in length, with bodies of pure white kaolin of equal size that appear to have been formed by the weathering of feldspar grains in place. In the kaolin-producing area, gravel and cobbles occur mainly at the base of the formation. Fig. 2 shows the relations of the Tuscaloosa and its kaolin deposits to the adjacent formations. Its base, on the eroded surface of the crystalline rocks, dips southeastward 50 to 60 ft to the mile, according to LaMoreaux.5 The upper surface of the Tuscaloosa is also an unconformity,

Jan 1, 1952

By Charles H. Behre

This paper discusses education and training for economic geologists other than petroleum geologists. Candidates enter economic geology through liberal arts colleges, engineering schools and university graduate study. Whatever their backgrounds, rigorous courses are desirable—now conceded in theory, but not adequately recognized in practice. Besides basic sciences (each studied long enough to give a fair comprehension of its basic tenets), a functional command of English and two modern foreign languages is needed, as well as a broad understanding of mining, milling and metallurgy. A year of economics and finance is recommended. Surveying and drafting are essential skills. Yet geology should be represented in each term; otherwise the initial enthusiasm for the science, once contact is broken, may never be regained. A five-year curriculum is thus designed to take care of all major requirements and culminate in the M. S. degree. This curriculum reduces "cultural" courses below the average liberal arts requirements, but this is regarded as necessary. The pursuit of "culture" is assigned, as in most engineering and medical curricula, to extra college years or extracurricular time. To avoid the danger of over-crowding the schooling, the Doctorate in geology is preferred wherever possible. Its two added years should permit wider professional education; more browsing in "cultural" pastures; due attention to broader social implications; and some training in the research now increasingly required of the mineral industry. "In-course" training through cooperation between school and industry is especially advo- cated. The Institute should take the initiative in stimulating this practice. Introduction Training a student in geology for a career in the mineral industry is still a moot question, one that is likely to be looked at from many different angles, each of which will reflect the background of the individual considering it. From what follows, the training of petroleum geologists is omitted since, although theirs is an equally important phase of economic geology, it is based upon different essentials. The general subject was recently effectively discussed, but from a somewhat different viewpoint, by Professor McKinstry.' The practical problems that confront the young mining geologist are highly varied and in the eyes of his employer apparently almost any demands seem justified. The mining executive wants from the mining geologist results related mainly to overall operations, reports or forecasts that are largely recordable on paper and chiefly in terms of "discovery thinking." The local mining engineer may have many specific questions of his own, chiefly relating to details of geology that apply to mining practice, which he will address to the mining geologist; these usually deal with production quantities; frequently also they necessitate the immediate handling of pressing but apparently minor matters: shall the drill be moved; how soon will we encounter the watercourse which made so much trouble for us above? The client employing a consultant often wants advice or good judg-

Jan 1, 1949

By Charles H. Behre

This paper discusses education and training for economic geologists other than petroleum geologists. Candidates enter economic geology through liberal arts colleges, engineering schools and university graduate study. Whatever their backgrounds, rigorous courses are desirable—now conceded in theory, but not adequately recognized in practice. Besides basic sciences (each studied long enough to give a fair comprehension of its basic tenets), a functional command of English and two modern foreign languages is needed, as well as a broad understanding of mining, milling and metallurgy. A year of economics and finance is recommended. Surveying and drafting are essential skills. Yet geology should be represented in each term; otherwise the initial enthusiasm for the science, once contact is broken, may never be regained. A five-year curriculum is thus designed to take care of all major requirements and culminate in the M. S. degree. This curriculum reduces "cultural" courses below the average liberal arts requirements, but this is regarded as necessary. The pursuit of "culture" is assigned, as in most engineering and medical curricula, to extra college years or extracurricular time. To avoid the danger of over-crowding the schooling, the Doctorate in geology is preferred wherever possible. Its two added years should permit wider professional education; more browsing in "cultural" pastures; due attention to broader social implications; and some training in the research now increasingly required of the mineral industry. "In-course" training through cooperation between school and industry is especially advo- cated. The Institute should take the initiative in stimulating this practice. Introduction Training a student in geology for a career in the mineral industry is still a moot question, one that is likely to be looked at from many different angles, each of which will reflect the background of the individual considering it. From what follows, the training of petroleum geologists is omitted since, although theirs is an equally important phase of economic geology, it is based upon different essentials. The general subject was recently effectively discussed, but from a somewhat different viewpoint, by Professor McKinstry.' The practical problems that confront the young mining geologist are highly varied and in the eyes of his employer apparently almost any demands seem justified. The mining executive wants from the mining geologist results related mainly to overall operations, reports or forecasts that are largely recordable on paper and chiefly in terms of "discovery thinking." The local mining engineer may have many specific questions of his own, chiefly relating to details of geology that apply to mining practice, which he will address to the mining geologist; these usually deal with production quantities; frequently also they necessitate the immediate handling of pressing but apparently minor matters: shall the drill be moved; how soon will we encounter the watercourse which made so much trouble for us above? The client employing a consultant often wants advice or good judg-

Jan 1, 1949

By T. D. Jones

MUCH the same story can be told for the lead industry for the year 1945 as for the three previous years. In response to inquiries as to new developments, invariably the answer has been, "No new developments-our men either too busy with the man-power problem or trying to get production out." Time and efforts of industry have been concentrated for the most part on war or readjustment problems. Now that V-E and V-1 day have passed, the lead industry can justly be proud of its record in World War II. As in previous wars, lead played an important role and one of its most spectacular uses was in the production of the atomic bomb. We read that the part lead played was rather obscure, but as a protective agent, lead played a most significant role. "Since the materials in the Pile Plant are intensely radioactive, all storage and handling must be done behind thick concrete walls or lead shields. The material is never seen and all operations are auto matically controlled by a foolproof remote control system especially designed for this purpose." (Chews. & Met., Sept. 1945.) When our armies invaded the European theater of war and made a landing on Normandy beach, gasoline and oil for the motive power were furnished through miles of armored lead pipe. This amaz-

Jan 1, 1946

By R. J. Stevens

The Roan Antelope Smelter commenced operations in October, 1931. As originally designed, its equipment consisted of one reverberatory furnace, 120 X 25 ft, two Peirce-Smith converters 12 X 20 ft, and one straight line casting machine. Since that time the following additions have been made: One reverberatory furnace 120 ft X 28 ft ('934) One reverberatory furnace 95 ft X 28 ft (1943) Two 12 X 20 ft Peirce-Smith converters (1934 and 1938) One 13 X 30 ft holding furnace (1938) One straight line casting machine and 2 ladle tilting quadrants (1934) The metallurgy of the smelting process is comparatively simple. However, there are several features of operation which are uncommon to most copper smelters: (I) The high grade of concentrate treated; this has always been about 50 pct copper. (2) The high flux burden on the charge. This is necessary because of the deficiency of bases in the concentrate and the high alumina content of the concentrate. (3) The frequent necessity of adding coal to the furnace charge to control the matte grade. (4) The high grade of matte produced. This has led to unusual converter problems. From the commencement of operations, the ore mined has come from the Roan Basin orebody. The concentrate produced from this ore consists mainly of chalcocite and shale with small proportions of other copper minerals. As mining operations extend to the Roan Extension orebody, the proportions of bornite and chalcopyrite in the concentrate will increase with a corresponding decrease in the copper content of the concentrate. Because of the concentrate grade the capacity of the reverberatory furnaces in terms of tons of copper produced per ton of coal burned is high. This ratio is usually over 2.2, and on especially favourable runs has reached 2.6. Reference to Table I shows that the iron content of the concentrate is unusually low. Only part of this iron is available for slag formation, the balance going to the matte. To make up this deficiency in bases, limerock is added to the furnace charge. This flux ensures a slag that is of the correct silicate degree, is suficiently fluid, of low specific gravity, and it counteracts the thickening effect of the alumina present. An ample supply of flux is obtainable from Ndola, 22 miles distant by rail. Although the reverberatory slag has a high copper content, the slag fall is low and the copper loss in the slag now rarely exceeds 1.0 pct of the total copper charged. The blister copper shipped is of such purity that only one fire refining operation has been necessary to produce a wirebar with properties comparable to electrolytic copper. Bismuth has always been the most troublesome impurity and consequently the problem of its control in the finished product has been of prime importance. Practically none is removed in the reverberatory furnace. The bulk of the elimina-

Jan 1, 1949

By Adrian C. Dorenfeld

Laboratory data form the basis for the design of flotation circuits. These data, obtained from testing samples of the ore, should show the optimum con- ditions for concentrating the ore and the effects of change in process vari- ables. Among the more important variables commonly met in flotation practice are: Liberation Size-This is the particle size at which substantially all of the valuable minerals are detached from the gangue minerals. Reagent Additions- Experimental data will show the reagents used and their quantity, quality, and point of addition. Pulp Density-This is an important variable in the design of the flotation circuit because it is one of the factors determining the size and number of flotation cells. Flotation Time-The time necessary to make the separation into concentrate and tailing depends on such factors as particle size and reagents used and must be known for determination of the size and number of flotation cells in the plant. Temperature of Pulp-Temperature affects flotation reactions. Water at approximately room temperature is satisfactory for most flotation separations, but some minerals such as fluorspar are best floated in hot water. Type of Circuit-Many types of circuits can be designed, as discussed in detail later. The laboratory tests should provide data for design of the plant circuit best suited to the ore. Water-Knowledge of the quality of the future plant's raw water is important because water quality may drastically affect flotation results. If possible, flotation tests should be made using samples of the water to be used in the plant. Flotation results may vary with seasonal temperatures and with circulation of reclaimed water. Experimentation can show whether it will be necessary to provide for heating, cooling, treating, or reclaiming the water. Uniformity of Ore-The extent of variation of the ore in hardness, grind- ability, mineral content, and floatability should be investigated so that the designer can ascertain methods to overcome problems caused by ore variations. Settling and Filtration Data-To design the plant flotation circuits, settling and filtration rates and ultimate percentage solids of the various products must be determined. Corrosion and Erosion-Corrosion and erosion tests should be made on the flotation pulps, particularly if the pulps are acid or at an elevated temperature, so that suitable materials of construction can then be chosen.

Jan 1, 1962

By A. M. Gaudin, J. G. Morrow

FLOTATION requires the existence of a definite contact angle. This contact angle, the surface tension of the solution, and adsorption at the solid-fluid interface are quantitatively related. Adsorption of dodecylammonium acetate on hematite was measured for a wide range of concentrations of reagent in solution. Similar measurements for quartz have already been made. Contact angle measurements were then made on polished surfaces of hematite and of quartz immersed in aqueous dodecylammonium acetate solutions, and a functional relationship was sought between adsorption density at the mineral-solution interface and the contact angle. Finally, the surface tension of the aqueous amine acetate solutions was measured. These data were combined to give an evaluation of the work of adhesion for the three-phase system. Specular hematite was crushed and then ground dry in a laboratory porcelain mill, with flint pebbles, to pass a 200-mesh screen. The ground product was sized in a Haultain infrasizer, and one of the granular sizes (cone No. 3) was used in all adsorption tests. A hand magnet was used to remove magnetite and abraded iron. Quartz was removed in a Frantz isodynamic magnetic separator. The purified hematite was leached in aqua regia, washed with distilled water until the washings appeared free of electrolyte by conductance measurement, dried in a low-temperature oven, and stored in a pyrex container. The specific surface of the closely sized hematite was determined by the krypton gas adsorption method.' Three measurements gave an average value of 1350 sq cm per g. Chemical analysis showed Fe -69.37 pct, insol = 0.72 pct. The quartz used in the flotation tests had been prepared by Chang" for an earlier investigation. Demineralized distilled water was used for all test solutions. Dissolved salt content was of the order of 0.03 ppm, expressed in terms of sodium chloride, as estimated from conductance measurements. Dodecylammonium acetate was obtained from Armour & CO. in two forms, the unmarked compound and a preparation marked by carbon 14 in the hydrocarbon chain of the aminium ion. Specific activity of the active salt was 0.134 millicurie per g. The important physico-chemical constants for the primary amine salt have been reviewed by de Bruyn. The calculated effect of hydrolysis of amine salt on pH of aqueous solutions and the effect of pH on the distribution ratio of the alkylammonium ion to free amine are of particular interest. All other chemicals used in this investigation were of analytical reagent grade. A column method' was used for adsorption work. Attainment of equilibrium distribution in the adsorption column depends on the solid-solution contact time, hence upon the volume of solution passed. It was assumed that contact time required for equilibrium would be a maximum for the lowest reagent concentrations. On this premise it was demonstrated experimentally that the passage of 500 ml of solution through the mineral bed was adequate. An aliquot (1 to 5 cc) of the solution to be analyzed was transferred to a small pyrex cup and allowed to evaporate to dryness at room temperature; 4 or 5 mg of unmarked amine acetate were added to the dried sample and the cup and its contents were transferred to the combustion system for analysis. Evaporation at room temperature must be emphasized, as even slightly elevated temperatures result in loss of reagent. A laboratory model G Beckman pH meter equipped with a glass electrode was used to measure pH of amine acetate solutions. The technique of internal gas counting of radioactive carbon dioxide in a Geiger-Muller counter was used. Developed originally by Brown and Miller,- his method was adapted to the analysis of carbon-14 marked flotation reagents by Chang, de Bruyn, and Bloecher. nalytica1 method and procedures have been described in detail by Bloecher.' Contact angles were measured by the captive-bubble technique." The mineral specimens were carefully selected to avoid cracks and inclusions of other minerals. All specimens were mounted in plastic and polished to produce a smooth surface. The final polishing and contact-angle measuring

Jan 1, 1955

By Fred Allison

THE magneto-optic method of analysis had its origin in experiments1 which were designed to detect and measure a time lag in the Faraday effect and later to study this time lag as a function of the wave length of the light.2 Faraday discovered in 1845 that a beam of plane polarized light, when passed through a transparent, isotropic medium traversed by a magnetic field of force parallel to the direction of the light, suffers a rotation. The direction of rotation is reversed with the reversal of the magnetic field and its magnitude depends upon the strength of the field, the length of the path of light in the substance and the nature of the substance. This phenomenon of magnetic rotation is known as the Faraday effect. A question which had been of some interest for years was whether this power of a liquid to rotate polarized light is acquired instantly with the application of the magnetic field, that is, whether it is a case of instantaneity or whether there is a very small interval of time which intervenes between the application of the magnetic field and the consequent rotation of the light by the liquid; in other words, whether there is a time lag in the Faraday effect. Efforts to measure such a lag previously had met with failure. It was recognized at the outset' that since a time lag had escaped detection it must be extremely small, if to a measurable extent it exists at all. It became necessary therefore to adopt a timing device capable of making measures of almost infinitesimally small intervals. The velocity of light served as this timing device, a modification of a method originally employed by Abraham and Lemoine3 being adapted to the requirements of the problem. Since light travels about 30 cm. in a billionth of a second and since settings in our observations may be repeated with deviations not exceeding 3 mm.,

Jan 1, 1932

By Frances Hurd, Clark

Iv 1897, Roberts-Austen(l)$ found an arrest in the thermal curves of alloys of 60 per cent. copper and 40 per cent. zinc. This break occurred from 450° to 470° C. Shepherd, (2) working in 1904, was unable to detect any change in the direction of the thermal curve. In 1911, Carpenter and Edwards(3) confirmed the work of Roberts-Austen and called this a eutectoid transformation of beta to alpha plus gamma. Hudson') in 1914, showed that the beta constituent could be produced synthetically at temperatures below the transformation point. He believed the change in the beta was polymorphic in nature rather than a eutectoid. The work of Matsuda(32) in 1922 demonstrated this break by thermal analysis, microscopic investigations, dilatation, electrical resistance measurements, and a thermoelectric study. He believed the transformation to be continuous from 300° to 480° C., and comparable to the A 2 transformation in iron. Later, in 1924, Andrew and Hay, with electrical resistance measurements, confirmed Matsuda's work. Imai(28) showed the transformation to be progressive and therefore a function of the temperature rather than the time. He stated that it was neither a eutectoid nor an allotropic change of phase. Atomistically expressed, it was a change, not of atomic configuration, but of atomic energy of some kind; and again it was compared to the A 2 transformation in iron. Imai believed that his analyses by X-rays led to the same conclusion. In order to study this change, at 470'C., in homogeneous 60:40 brass, Homerberg and Williams «0> and Homerberg and Shaw(41) quenched their material in iced brine to obtain the beta solid solution and reheated at various temperatures. At 200° C., a change in the microstructure and physical properties occurred. A fine-grained structure, which they termed alpha and which had the appearance of a sorbitic steel, appeared, with an increase in the tensile strength to 82,750 lb. per sq. in., and a Brinell ball hardness of 240 with 3000 kg. load. At 470° C., the alpha

Jan 1, 1927

By C. A. Stetefeldt

Metallurgical processes cannot be conducted successfully With out the aid of analytical chemistry. The great perfection of Iead smelting in the West, for instance, has only been accomplished by the analysis of ores, fluxes, slags and all products of the furnace. Ores are mixed and fluxed to obtain a slag of desired composition. Account is even taken of the composition of the ashes obtained from the coke. The " muscular " smelter has left the field forever! This state of affairs has been induced by sharp competition, i.e., by a com plete separation of the industries of mining and reducing ores, not by the liberality and wisdom of directors and stockholders to pro vide laboratories and engage chemists, or by their love for scientific investigation. It would be considered absurd, at present, to run a lead-smelter, a blast-furnace for pig-iron, or a Bessemer plant without the assist ance of a well-equipped laboratory and a chemist; but it is con sidered quite sufficient to provide amalgamation- or lixiviation works merely with a crude assay-office, and an assayer who is paid less than a laborer in the mill. In my opinion, this will change in the near future. By the ex clusion of Mexican lead-ores, and their growiring scarcity in the West, smelters have been forced to raise their charges on so-called dry silver-ores, and cannot handle the latter now in such unlimited quantities as formerly. The inevitable result must be that the sur plus of these dry silver-ores, especially those of low grade, will be reduced by processes cheaper than smelbing; and here the introduc tion of lixiviation has an excellent field, provided the muscular lixiviator has an able chemist for an assistant. It is to be regretted that so little analytical work has been done in lixiviation. We know almost nothing of the composition of roasted ores before and after lixiviation; of the constitution of the first wash water and of lixiviation-solutions after prolonged use; of the chemistry of sodium and calcium sulphides; of the col-hposition

Jan 1, 1892

By Thomas V. Falkie

4.3-1. Introduction. DEFINITION OF PRODUCTION SYSTEMS ENGINEERING. Surface mines, like most other mining and manufacturing operations, are usually organized along functional departmental lines. Frequently a mine manager will have his responsibilities divided among production, maintenance, administrative, and engineering functions. Often these are separate departments, but various combinations and variations of these functions can be found in mining companies throughout the world. The production function is responsible for physically removing the ore from the ground, processing it, and shipping the product to its market. The production manager supervises and is responsible for all man-machine systems necessary to extract and process the ore. The maintenance function, which is sometimes included within the framework of production, has the task of insuring the maximum availability and longevity of equipment needed to produce the ore. The administrative function is responsible for accounting, personnel, industrial relations, purchasing, public relations, property, and other related staff functions. For purposes of this chapter, engineering can be described as the function which plans, designs, and supervises construction of physical plant and equipment. In this context engineering includes mechanical, civil, chemical, electrical, and mining engineering. However, another phase of engineering is to prepare plans to insure that the various man-machine components function in an optimum way towards the single most important goal of any enterprise-the maximization of return on the investors' money. Along with the planning, another duty of engineering is to audit all phases of the operation for the purpose of recommending improvements toward this same general goal. These latter two ideas form the basis for a discussion of production engineering and systems engineering. Production engineering is a catchall, problem-oriented function whose duties can include: 1) solution of day-to-day production problems, 2) short-

Jan 1, 1968

By Oliver M. W. Sprague

THIS gold problem is full of complications and can hardly be handled adequately or comprehensively in any short period of time. Perhaps I might begin by mentioning a few aspects of the subject about which I suppose there will be no disagreement. The first of these is that we already have a stock of monetary gold in the United States far in excess of what is needed to support any desirable increase in the present volume of currency and credit. The second is that this already superabundant gold stock is certain to be considerably enlarged during the course of the war, and presumably during the months of readjustment following its conclusion. Some billions of additional gold, we may reasonably presume, will come into the country during these next few years, thus increasing the aggregate monetary gold stock from the present eighteen billions to perhaps twenty- two or even twenty-five billion dollars.

Jan 1, 1940

The First Conference of the Powder Metallurgy Committee convened in the East Foyer of the Hotel Waldorf-Astoria, New York City, at 9:45 a.m., on Feb. 21, 1944, Mr. John Wulff, General Chairman, presiding. THE CHAIRMAN.-In behalf of the American Institute of Mining and Metallurgical Engineers I welcome all members and guests to this conference on Powder Metallurgy. We hope that this meeting will give expert and novice in the field a chance for discussion. Unfortunately, the subject has been overemphasized by some, and, of late, severely criticized by others. We have here today powder producers, fabricators, and engineers of different viewpoints, who can make the meeting a success. Such success depends not only on the caliber of the papers presented but more so on the discussion. To give you time for a free exchange of views, the papers have been shortened purposely. With the hope that you will all benefit by this conference, I shall turn the meeting over to the Chairmen of the morning session, Mr. Roland P. Koehring, of Moraine Products Division of General Motors, and Dr. R. K. Waring, of the New Jersey Zinc Company. SESSION ON DESIGN FACTORS IN POWDER METALLURGY R. P. Koehring and R. K. Waring presiding The opening paper of the session was presented by Mr. Fred P. Peters, as follows:

Jan 1, 1945

By B. E. Mix, L. M. Barker

THe present methods of unloading ore and coarse-crushing at the Magna plant of the Utah Copper Co. are the developments of the pas five years. Hand dumping and breaking have given way to the rotary car dump and large gyratory; and the bucket elevators and stationary screens have been replaced by conveyors and shaking screens. The coarse-crushing plant may be broadly divided into two units the primary crushing and the secondary crushing, or primary roll, unit The former was erected in 1923; with the exception of the excavation the construction was carried on by forces of the company. Excavation was started in the middle of March, the first concrete was poured July 16, erection of the steel building started Oct. 30, and the unit was com pleted and operating Dec. 30. The unit has a capacity of over 24,001 tons of ore per day, and cost more than a million dollars. Remodeling of the primary-roll unit extended over a period of years preceding this some of the work having been done as early as 1918. Delivery of Ore from Mine, Yard Storage, and Handling Ori Cars to and from Primary Crushing Plant The ore is transported, in steel cars of 80 tons capacity, from the min' to the mill, where a reserve tonnage of loaded cars is maintained. Malle locomotives, handling trains of 45 cars, or approximately 3600 tons o ore per train, deliver the trains to a storage yard which contains thre tracks—a passing track and two storage tracks. All of this trackage i equipped with an overhead trolley system, so that electric locomotive can be used in yard switching. The storage tracks have a total length of 4500 ft. and provide storag space for 140 cars. The passing track, besides permitting switchin room for locomotives, is used for storage purposes between train arrivals thus giving intermittently a total storage capacity for the yard of approxi mately 200 cars. The amount of ore stored at any one time, howeve

Jan 1, 1926

By J. J. Gilvarry, B. H. Bergstorm

The first part of this paper describes a new approach to the problem of energy relationships in fracture and comminution. The basic theoretical method used (as contrasted to previous empirical or semi-empirical approaches) is an attempt to verify or disprove the hypothesis of von Rittinger, In the second part of the paper, theoretical conclusions for the three headings of single fracture, plural fracture, and comminution are tested. Agreement between theory and experimental results is demonstrated. The classical hypotheses on the energy relationship in brittle fracture are those of von Rittinger-that the energy required is proportional to the new surface formed— and the alternative one of Kick.' Over the years, repeated attempts have been made to discriminate experimentally between the two assumptions, or to replace both of them, as has been done by Bond? However, no semblance of agreement seems to exist among different investigators. This paper is the first in a series essaying a new approach to the entire problem of energy relationships in fracture and comminution. The purpose of this program of research is to verify (or disprove) the hypothesis of von Rittinger. In contrast to previous empirical or semi-empirical approaches to the problem, the basic method adopted is theoretical. The prime aim is to determine the distribution function for fragment size theoretically and to verify the predicted distribution experimentally. This approach should make possible determination of the total surface of the particles by integration over the corresponding distribution function; one may hope that this direct procedure will yield more definitive results than use of gas adsorption or other methods. The surface area so obtained can then be compared with experimental energies, as obtained by Bergstrom, Sollenberger, and Mitchell,4 for example. It is convenient to distinguish between single fratture, plural fracture, and comminution. Single fracture of a brittle solid is defined as fracture by an external stress system which is removed instantly and permanently when fracture is initiated. Plural fracture consists of single fracture of the original specimen, followed by a sequence of only a few secondary fractures; comminution differs in that the sequence of secondary fractures consists of a large number of repetitive steps. For single fracture, Gilvarrys has given a rigorous derivation of the proper distribution function for fragment size, based on a closely defined physical model and deduced strictly by the laws of probability. Gilvarry and Bergstrome have compared the predictions of the theory with experiment, and have found excellent agreement. The prior work of Gilvarry and of Gilvarry and Bergstrom considers only single and plural fracture. The purpose of the present paper is to extend the discussion to the case of comminution. For prefatory purposes, the theory of Gilvarry for single fracture will be outlined. The considerations will then be applied to the cases of plural fracture and comminution. SINGLE FRACTURE The derivation is based on the Poisson law.7 For Points distributed with mean density y over a domain, this law states that the probability p(t)dt of one point lying in the range t to t + dt with none in the interval 0 to Ms p(t)dt = ye-yt dt. For this distribution to be valid, it is necessary and sufficient that the points be distributed at random, individually and collectively in the sense of ~~~.7 The former qualification requires that the position of One Point be independent of another, and the latter implies that the probability of a region containing a

Jan 1, 1961

By J. J. Foster

MOST of us will, I think, agree that never before in the history of the coal industry has the human side of our business been so important as today. Since, even in wholly mechanized mining, labor cost is such a large percentage of out total cost we are all deeply concerned not only about the present attitude of our employees but particularly about the future, when the industry returns to a "survival of the fittest" basis. Many things could and should be done about our employee relations in the coal business. Failure to recognize these obligations and do something about them may lead to serious consequences, the least serious of which will be the loss not only of many of our better employees but a large portion of our potential employees, as they graduate from our schools to other in¬dustries. Some of these things should be handled by the industry as a whole whereas others should be done by individual companies. Due to varying conditions and size of organizations it would, at best, be necessary to vary a program to meet the individual needs of each operator.

Jan 1, 1945

By B. A. Wilcox, A. H. Clauer

The steady-state creep of TD Nickel NL + 2 001 pct TltOz) has been studied orer the telirperatve range 325&apos; to 1100O and the stress range 15,000 to 36,000 psi. At high temperatures (aboue 0.5 T& gran-boundary slzding is the )nost znportant )node of creep deformation, and the steady-state creep rate, is, can be related to stress and temperature by: where Q = 190 kcal pev mole and n has an unusually high value of 40. A creep mechanism based on cross slip of dislocations around The O2 particles can satisfactovily explain the low-temperature (T < 0.5 T,) cveep behavior, and the follo wing relation is applicable: Q, (a) is found to decrease from 57 to 46 kcal per mole as the stress is increased from 32,000 to 36,000 psi. THERE have been a variety of theories proposed to explain the influence of dispersed second-phase particles on the yield strength and flow stress of metals, and these have been reviewed recently by Kelly and icholson.&apos; However, only several attempts2"4 have been made to develop mechanistic treatments which characterize the creep behavior of dispersion-strengthened metals, and to date these have not been fully evaluated experimentally. weertman2 and Ansell and weertman3 proposed a quantitative creep theory for coarse-grairzed dispersion-strengthened metals, based on the concept that the rate-controlling process for steady-state creep was the climb of dislocations over second-phase particles, as suggested by choeck. The theory predicted that the steady-state creep rate, <,, was proportional to the applied stress, a, for low stresses and that is a4 o for high stresses. The activation energy for creep, Q,, was equivalent to that for self-diffusion, Qs.d., in the matrix. Some limited experimental evidence in support of this theory was obtained on a recrystallized Al-Alz03 S.A.P.-type alloy by Ansell and Lenel.6 Ansell and weertman3 also developed a semiquanti-tative theory for high-temperature creep of lineg-rained dispersion-strengthened metals in order to explain their results on an extruded S:A.P.-type alloy, which had a fine-grained fibrous structure. They suggested that the rate of dislocation generation from grain boundaries was the rate-controlling process, and fitted their results to the equation: where Q, was found to be 150 kcal per mole, i.e., QC- 4Q,.d. in aluminum. Similar high activation energies for creep7-&apos;&apos; and tensile deformation" of dispersion-strengthened alloys have been observed by other investigators for S.A.P.,&apos;" indium-glass bead omosites, and Ni + A1203 alls.&apos; There is no general agreement regarding the mechanisms involved in the creep of dispersion-strengthened metals, and this is due in part to the lack of detailed studies relating the structures of crept specimens to the mechanical behavior. The present investigation on thoriated nickel was undertaken with the aim of studying the structural changes which occur during creep of a dispersion-strengthened alloy and rationalizing the observed mechanical behavior in terms of the creep structures. EXPERIMENTAL METHODS The material used in this investigation was 1/2-in.-diam TD Nickel bar, which contained 2.3 vol pct Tho,. Obtained from E. I. duPont de Nemours & Co., Inc. The final fabrication treatment by DuPont consisted of -95 pct reduction by swaging followed by a 1-hr anneal at 1000°C. Transmission and replica electron microscopy revealed that the material had a fine-grained fibered structure with an average transverse grain size of -1 p and a longitudinal grain size of 10 to 15 p. Selected-area diffraction indicated that the fiber axis was parallel to (OOl), in agreement with the results of Inman eta1." All creep specimens were vacuum-annealed at 1300°C for 3 hr prior to testing. Transmission electron microscopy showed that the only structural change due to annealing was a slight decrease in dislocation density, confirming the reported high degree of structural stability.13 Furthermore, recrys-tallization or grain growth during creep was never observed. The structure typical of uncrept material (after the 1300 C, 3-hr anneal) is shown in Fig. 1. The grain boundaries are predominantly high angle and. although some areas show a tangled cell structure, the grain interiors are relatively dislocation-free. Individual dislocations are strongly pinned by the Tho2 particles; i.e., very rarely did dislocations move within a thin foil. The grey "halos" around some of the larger particles which protrude out of the foil surface arise from contamination in the electron microscoge. The Tho, particle size ranged from -100 to IOOOA, and the distribution is shown in Fig. 2. The technique used to obtain the data in Fig. 2 consisted of dissolving the nickel matrix in acid, collecting the Tho2 particles on cellulose acetate, and measuring about 1000 particle diameters in the electron microscope. Similar results were obtained by measuring about 600 particles in thin foils, an; the average particle size was found to be 2r, = 370A. Using the data in Fig. 2 (annealed structure), the mean planar center-to-center particle

Jan 1, 1967

By R. A. Vandermeer, Paul Gordon

On the basis of a unified concept, theoretical erPressions for grain boundary migration in recrys-tallization are derzved for impurity-controlled and impurity-independent migration. The expression in the former case is analogous to that Previously derived by Lucke and Detert, and in the latter is shown to be equivalent to that usually obtained on the basis of absolute reaction rate theory. The equations are tested with quantitative experimental data for boundary migration obtained for the recrystallization of poly crystalline zone-refined alumimnz and for binary "alloys" of this aluminum with 0.00021, 0.00043, 0.0017, 0.0034, 0.0068, 0.0124, and 0.0256 at. pct Cu, respectively. All the essential characteristics of the e@erimentally determined boundary migration rates check both qualitatively ard quantitatively with the predictions of the theoretical equations. THE rates of transformations are customarily analyzed phenomenologically in terms of the two component rates—N, the rate of nucleation and, G, the rate of growth of the nuclei. The scientific aim of both theory and experiment is to describe the fundamental atomic phemmena involved in these two component processes with the hope that parameters calculated from theoretical equations will check those found experimentally. In solid state transformations, the theoretical and experimental problems are both generally of almost prohibitive complexity, for in addition to changes in composition and in such properties as density which may accompany transformations in amorphous, nonrigid materials, transformations in crystalline substances also involve structural changes, crystal reorientations, and the development of stresses. In studying such transformations it thus becomes; highly desirable, if not essential, to focus on a transformation and a set of conditions which minimize the number of active variables. This principle has been applied with considerable success by Cohen and his associates&apos; in their evaluation of nucleation theories using the martensite transformation as the basis of study. A similar possibility exists for the evaluation of growth theories by the use of recrystallization after cold-deforming. If an unalloyed metal is employed as the subject of investigation, the recrystallization transformation involves basically only a change in strain-conditions and orientations. In spite of this possible simplilfication, however, until recently little quantitative success has attended attempts to correlate recrystal1ization parameters measured experimentally with those calculated theoretically. It seems highly probable that this lack of success may be attributed, both in the experimental and theoretical treatments, to one or more of the following factors: a) conditions have usually been studied under which apparently* both nucleation and growth are active;

Jan 1, 1962