Search Documents

By A. L. Holley

Those who are familiar with working gas furnaces will perhaps admit that the ordinary producer is the least satisfactory feature of the- whole system, chiefly by reason of its great waste of fuel, both above and below the fire. The waste of fuel in cleaning the fire has not, as fdr as I am aware, been carefully measured ; it has been roughly estimated at various works as averaging twenty per cent. to twenty-five per cent. The coke that falls into the ash-pit is largely mixed, if not stuck together with clinker; when this coke is not recovered and utilized (and where coal is cheap it does not pay to recover it), the waste is certainly as high as above estimated. Cleaning a fire on a grate (especially a fire of dirty coal, like much of our Western coal), by inserting a few temporary grate-bars, then withdrawing the regular grate-bars and letting the whole lower part of the fire tumble into the ash-pit, must necessarily be wasteful of fuel, but it has been found to be the most practical system. The fire under a boiler should be thin, to insure perfect combustion; hence it may be moved from one side to the other, so that .the clinker and ashes may be uncovered and removed. But a producer fire should be so thick that carbonic oxide only shall rise from it; a thick fire cannot be thus manipulated. In several of the French works the ordinary producer without grates is employed ; the whole body of the fire rests on the floor of the ash-pit. It did not seem to me that less fuel was wasted here than with grates in cleaning fires. The bottom layer of the fire had to be drawn out with hooks, and there was nothing to prevent much coke from coming away with the clinker and ash. A producer shaped like a cupola furnace has many advantages, but if grates are employed the waste of coke in cleaning is not lessened. But the waste at the bottom of the fire is only a part of the waste in the ordinary producer. Mr. Emmerton, chemist to the Juliet Iron and Steel Company, has lately made a number of gas analyses from the producers of that company, worked with impure Illinois

Jan 1, 1880

THE purpose of this chapter is to present a general outline of the basic open-hearth process for the benefit of students, practicing open-hearth operators, and metallurgists who wish to review the subject. The discussion is limited to a description of the sequence and purpose of the operations, illustrated by data and examples. Subsequent chapters deal with more detailed and fundamental studies of the subject. The function of the basic open-hearth furnace is to convert various types of ferrous material into finished steel of given com- position and quality. In comparison with other steelmaking methods, the basic open-hearth process is one of the most versa- tile, both from the standpoint of the raw materials that can be used and the types of steel that can be produced. The process can be considered as a sequence involving melting, refining, and deoxidation. With some types of liquid-metal charges, the melting stage is not present, but refining and deoxidation in varying degrees are fundamental features of the process. GENERAL DISCUSSION OF BASIC OPEN-HEARTH PROCESS The first consideration in open-hearth practice is the type of charge on which the operation is based. This consists of three components-fluxing, oxidizing, and metallic materials. Fluxes. In the basic process the fluxing material is primarily lime, added in the form of either limestone (CaC03) or burnt lime (CaO) . This is supplemented by magnesia (MgO) and lime from the furnace bottom and banks. The function of these fluxes is to form a slag with the silica (SiO2) , manganese oxide (MnO), iron oxides (FeO and Fe203), and phosphorus oxide (P205) that are produced by the oxidation of varying amounts of the silicon, manganese, iron, and phosphorus in the charge during melting and refining. The slag, composed of the basic fluxes and the neutral and acid oxides, floats on top of the steel bath when the charge is melted. The composition of this slag depends on the amount of each slag-forming element present in the charge and on the extent of oxidation of these elements during the course

Jan 1, 1964

By P. D. I. Honeyman

DURING 1938 many copper companies again felt the economic pinch and smelter operations were often on a reduced basis which some- times resulted in intermittent operations and complete shutdowns. During the last half of the year production was stepped up and smelting operations resumed a more normal appearance. One of the present-day trends in reverberatory sme1ting is definitely toward high-tonnage operations. i\ t the Phelps Dodge Corporation's Douglas plant, the reconstructed 107 by 26- ft. reverberatory furnaces are operated at the rate of 1000 tons of solid charge per day. The arch, all of silica brick; is sufficiently high above the bath to give

Jan 1, 1939

By Thomas C. Baker

The Fresnillo unit of the Mexican Corporation, S. A., is situated at the old historic mining town of Fresnillo, Zacatecas, Mexico, 33 miles north of the city of Zacatecas and 750 miles south of El Paso, Tex. It is connected with the Mexican Central Railroad by a broad-gage spur 5.5 miles long, belonging to the company. Fresnillo is surrounded by a broad semi-arid valley on the Mexican plateau at an elevation of 7300 ft. The monotony of the valley is broken by a number of low hills. Near the town of Fresnillo is the " Cerro de Proano," an elliptic-shaped hill of gentle slope, rising out of the plain to a height of 325 ft.; the base has a major axis of 4500ft. and a minor axis of 3000 ft. In this hill is the silver-bearing mineralized zone, which comprises past and present mining operations. (In this paper money values are expressed throughout in American currency and the dry short ton of 2000 lb. is used.) The discovery of ore at Fresnillo is credited to the Spaniards, soon after the conquest of Mexico. There are, however, no authentic records to show the amount of work done by them. In 1832, the State of Zacatecas took possession of the property and operated it. Evidently the rich ore above the horizon of the plain had been fairly well exhausted, as an old record states that thirty shafts were used for unwatering, requiring 300 men and 1500 animals. The cost of pumping alone amounted to $150,000 a year. In spite of the fact that cheap convict labor was used, mining costs were reported as $20 and treatment charges as $20 per ton. In 1835, the state was obliged to seek foreign capital, and a company formed in London secured a controlling interest in the property. This new organization sank two shafts, one 11 by 19 ft. and the other 10 by 15 ft., to unwater the mines and extract ore. Large Cornish pumps were purchased in England and hauled overland from Vera Cruz; engines also were installed to operate the arrastres (grinding mills) in the patio process of ore treatment. Substantial buildings were erected and operations were conducted on a large scale, for that period. The patio, the largest in Mexico, was 1150 ft. square. The costs for 1850 were:

Jan 1, 1925

By S. R. B. Cooke, H. S. Choi, I. Iwasaki

Oleic acid is the chief ingredient of fatty acids used as collectors in nonsulfide flotation. With a few notable exceptions, the various quantities of saturated and other unsaturated acids comprising the remainder are usually unspecified. There have been occasional investigations to determine the collecting ability of these other acids and their effect on collection with oleic acid, but much remains to be done in this field. Hukki and Vartiainen, on the basis of tests using palmitic, oleic, and linoleic acids and an impure linolenic acid, concluded: "The collecting power of fatty acids used in flotation increases with increasing unsaturation of the hydrocarbon chain." ' Their work was concerned mainly with the response of ilmenite to the foregoing collectors, although tests were also made with magnetite, pyrite, hematite, and rutile. Cooke and Nummela, employing an almost identical technical procedure to evaluate flotation of hematite, magnetite, and goethite with various fatty acids, including oleic, linoleic, and linolenic acids of the highest purity obtainable, found: "The effectiveness of 18-carbon unsaturated fatty acids, as collectors for hematite, decreases with increase in the number of non-conjugated double bonds." 2 Vn the foregoing investigations, collector efficacy was measured on the basis of reagent addition in moles per liter. Sources of fatty acids which may be used as collectors are legion, but provided the oleic acid content is high enough, cost is normally the determining factor. Usually this restricts severely the purity of the collector in terms of its oleic acid content. Within the past year or so users of crude oleic acid have become somewhat more discriminating, apparently realizing that some of the organic acid impurities may exert deleterious effects upon certain separations. Marine fish oils have been used as collecting agents, particularly in the earlier days of froth flotation. Currently their use is restricted in this field to relatively minor applications, although they are cheap sources of fatty acids. In an effort to increase the range of uses for fish oils, the U. S. Fish and Wildlife Service has awarded contracts to study these materials as sources of new products suitable for commercial development. Funds for these investigations were provided by the Saltonstall-Ken-nedy Act of 1954. One such contract was awarded to the University of Minnesota School of Mines and Metallurgy for the purpose of investigating the use of fish oil fatty acids and their derivatives in ore flotation. Besides the esters of various saturated aliphatic acids and of palmitoleic and oleic acids, fish oil also contains esters of monoethenoid and polyethenoid acids with 20, 22, and 2 carbon atoms. The basic purpose of the investigation was to determine whether the longer-chained unsaturated acids possess collective properties superior to those of the C,, monoethenoid oleic acid, the C16 monoethenoid palmitoleic acid, or the saturated C,, stearic acid and its shorter chain homologues; whether highly unsaturated acids have merit as collectors; whether rela-

Jan 1, 1960

By Eugene Grace

IN THE careers of the men to whom I have referred we find typified the development of the chief prob-lems of engineering. The first is to shape and direct the forces of nature and thus to bring the world's resources to add to the comfort and welfare of man-kind. That, in a word, is the problem of production. Engineers have made a supreme contribution to the solution of that problem. But I feel that we have two somewhat newer branches of engineering which must command more and more of our attention. Those are what might be termed commercial and human engineering. Of what value is all our efficiency in pro-duction if we do not distribute efficiently, economically and effectively? And of what value is any of it unless we can add to the happiness and deeper satisfaction of those engaged in industry, as well as those who enjoy its -products? I predict that the outstanding advances in business over the next ten years will be in improved merchan-dising and distributing methods. Herein lies a wide field of opportunity for the engineer. We have briefly reviewed certain qualities of engi-neers who have become successful business executives. Is it possible for us to say that the material success of all these men was due to any one characteristic com-mon to each one of them? Indeed, I venture to assert that there is one quality which, in the last analysis, is determining as to whether any roan shall realize material success in this world of ours. That quality-so notable in the character of each one of the men I have named-is sound judgment. Moments arise in every life when it is necessary to say "yes" or to say "no" to a particular proposition or to a proposed line of action. It is the man who says "yes" at the proper time and "no" at the proper time who, in the final analysis, realizes business success. The ability to do this wisely is the mark of sound judg-ment, which is necessary in a business executive. I have known many business men seemingly slow in their mental processes, possessed apparently, of little imagination and of none of the flair which gives fasci-nation to so many characters, and yet who, when crises come-be they big or be they little-are able so to steer their business courses that they move in the right direction instead of into shallow waters or upon the rocks of trouble.

Jan 4, 1928

By Seishiro Hirakawa, Hiroshi Tokunaga, Hironori Nakamura

Two unique processes of reclaiming zinc from various secondary materials were developed and have successfully been operated for years by Mitsui Mining and Smelting Co. These processes were established based on the characteristic and local energy conditions; i.e., (1) at Miike Smelter, located above the largest coal deposit in Japan, a combination of slag fuming and semi-blast furnace (MF)processes takes advantage of using coal and the carbon bearing briquette residue from the vertical retort plant as reducing agents, (2) on the other hand, at Kamioka Smelter, a direct reduction of zinc-bearing lead slag by using electric furnaces is of advantage in view of cheap electric power supply from our own hydraulic power plants. The former also consumes lots of zinc bearing fines and drosses from various steel plants, fabricators and secondary zinc smelters, while the latter, zinc leach residue from its own electrolytic plant

Jan 1, 1976

By R. F. Frantz, T. P. McNulty

The upper-level mineralization of the din Buttes, Arizona copper orebody consists primarily of dilute copper silicate impregnation in fault clay and throughout the altered limestone hostrock. Cuprite and native copper are minor with true chrysocolla rare. Owing to the high calcium carbonate and to the hydrogen ion exchange capacity of the clays, acid leaching would be economical only with cheap acid available. Leaching of the silicate copper with reagents other than sulfuric acid is slow and incomplete unless the ore is first heated to disorder the mineralized grains and to reduce partially the contained copper. Following heat treatment, 70 to 90 percent of the nonsulfide copper can be dissolved in aqueous anrmonium carbonate. Recovery of a pregnant solution by counter-current decantation is effective provided ammonium carbonate solution is added to the washing stages in order to oppose adsorption of dissolved copper by clays in the residue. Thermal stripping of the pregnant solution permits recovery of ammonia and carbon dioxide while precipitating copper either as oxide or carbonate. The research program was carried from batch tests through continuous miniplant operation to a five-month campaign in a 20 TPD continuous pilot plant. Pilot plant results, the relationships among key varibles, and a detailed flowsheet are given.

Jan 1, 1973

By John Hillman

Reconstruction of the British mining industry began shortly after nationalization in 1947 and continued until well into the 1950s with the support of the government. This support diminished as plentiful supplies of cheap oil from the Middle East made many coal mines uneconomic. The planned rundown which followed was foreshadowed in the 1965 White Paper which outlined financial measures to speed the closure of uneconomic collieries. The decline appeared likely to continue into the 21st century as the role of coal in UK energy requirements became less and less significant. This policy was well on course in 1973 when the oil crisis led to a complete reappraisal of the position. A government examination in 1974 of the coal industry then supported the National Coal Board's general strategy of major capital investment as set out in its 'Plan for Coal'. The plan was aimed at halting the intended decline in the industry's capacity and restoring it to 120 million tons of deep mined output in 1985. The plan proposed action along the following lines: Increase output by major investment in construction at existing collieries with sufficient reserves to give 13 million tons per annum extra output.

Jan 1, 1980

By Akira Ishizu, Nobuo Matsui, Hideo Yamamoto, Tatsuya Nagahama

At Kamioka Mine of Mitsui Mining & Smelting Co., Ltd., Japan there are three mills, treating a total of 6400 t/d of lead-zinc Ore. In the lead-zinc bulk differential flotation at Shikama Mill the addition of reagents is automatically controlled by the feed rate, the lead and zinc content in feed, froth and tailing, the pH and the concentration of cyanide ion in the pulp. As the zinc thickener overflow at Shikama Mill contains CU(CN)3--, ZnS, CdS, CN-, xanthate and frother, all the ingredients in the over- flow other than CN are floated by using the Nagahm flotation machine, and the water containing only CN- is effectively recycled to the lead- zinc differential flotation circuit. In the lead-zinc straight differential flotation at Mozumi Mill, the overflow of tailing pond is recycled especially to the cleaning flotation circuit by decreasing the pulp density. Thus the integrated recycling of wastewater greatly reduces environmental problem and in addition, it generates sizeable profit.

Jan 1, 1977

By Andre Hubaux

In the writer's opinion, more stress should be put on field and microscope observations, as J. L. Gillson does. His discovery of relics of big labradorite feldspars from the Marcy anorthosite in all the other rocks is proof enough that previous field observations have been inadequate. The writer's field experience with anorthositic massifs is limited to the Egersund-Sogndal district in southern Norway; however, this is a very large and well exposed area. It seems to have so many points in common with the Adirondack region that a detailed comparison should be beneficial. This comparison was not possible 20 years ago, owing to the scarcity of geological data, at least for Norway. Both regions are now far better known-the Norway district because of the work of Professors Bugge and Barth33-35 and especially because of the extensive field and microscopic research of P. Michot,36-46 who introduced me in the field to the problems of that region.

Jan 3, 1958

By R. J. Stevens

THE Roan Antelope Smelter commenced operations in October, 1931. As originally designed, its equipment consisted of one reverberatory furnace, 120 X 25 ft, two Peirce-Smith converters 12 X 20 ft, and one straight line casting machine. Since that time the following additions have been made: One reverberatory furnace 120 ft X 28 ft (1934) One reverberatory furnace 95 ft X 28 ft (1943) Two 12 X 20 ft Peirce-Smith converters (1934 and 1938) One 13 X 30 ft holding furnace 6 (1938) One straight line casting machine and 2 ladle tilting quadrants (1934) The metallurgy of the smelting process is comparatively simple. However, there are several features of operation which are uncommon to most copper smelters: (1) The high grade of concentrate treated; this has always been about 50 pct copper. (2) The high flux burden on the charge. This is necessary because of the deficiency of bases'in the concentrate and the high alumina content of the concentrate. (3) The frequent necessity of adding coal to the furnace charge to control the matte grade. (4) The high grade of matte produced. This has led' to unusual converter problems. From the commencement of operations, the ore mined has come from the Roan Basin orebody. The concentrate produced from this ore consists mainly of chalcocite and shale with small proportions of other copper minerals. As mining operations extend to the Roan Extension orebody, the proportions of bornite and chalcopyrite in the concentrate will increase with a corresponding decrease in the copper content of the concentrate. Because of the concentrate grade the capacity of the reverberatory . furnaces in terms of tons of copper produced per ton of coal burned is high.. This ratio is usually over 2.2, and on especially favourable runs has reached 2.6. Reference to Table , shows that the iron content of the concentrate is unusually low. Only part of this iron is available for slag formation, the balance going to the matte. To make up this deficiency in bases, limerock is added to the furnace charge. This flux ensures a slag that is of the correct silicate degree, is sufficiently fluid, of low specific gravity, and it counteracts the thickening effect of the alumina present. An ample supply of flux is obtainable from Ndola, 2 2 miles distant by rail. Although the reverberatory slag has a high copper content, the slag fall is low and the copper loss in the slag now rarely exceeds 1.0 pct of the total copper charged. The blister copper shipped is of such purity that only one fire refining operation has been necessary to produce a wirebar with properties comparable to electrolytic copper. Bismuth has always been the most troublesome impurity and consequently the problem of its control in the finished product has been of prime importance. Practically none is removed in the reverberatory furnace. The bulk of the elimina-

Jan 1, 1947

By C. E. Julihn

Technology concerns the ways of doing things; mineral technology the ways of performing operations required for obtaining minerals from the earth and extracting their valuable constituents for man's use. At any particular time, technology is relatively fixed, as everyone tries to adopt the way of doing things that has proved most profitable; but improvements evolve from minor changes here and there, and occasion- ally entirely new methods are discovered. Technologic improvement thus characterizes any long-time view of the mineral industries. Its test lies always in reduction of costs; there is no other incentive for the adoption of new methods. Reduction in cost of producing metal from ore decreases, in turn, the amount of metal that must be obtained from ore in order to pay for its production. An advancing technology thus is characterized by utilization of ores of lower and lower grade. A very important result of this is an increase in the gross quantity of metal obtainable at any price level, since the earth's crust contains vast amounts of very low-grade ores and relatively insignificant amounts of very high-grade ores. Technologic advances have, therefore, been the means of rendering the metals both cheap and abundant. Though concern as to possible exhaustion of the world's ore deposits is warranted, it is conceivable that a transcendent technology of the future might supply metal requirements from what we

Jan 1, 1932

By E. J. Schmitz

The mining of the Triassic coals of the Richmond basin has been carried on, upon a larger or smaller scale, for more than a hundred years. Notwithstanding the close proximity of the field to a large city and to tide-water, assuring both a good home-market and cheap transportation, and notwithstanding the good quality of the fuel and the great thickness of the principal bed developed and worked, operations in this field have been conducted with but limited success. The basin comprises about 189 square miles, being from 24 to 31½ miles in length by 5½ to 10 miles in width. Not much more than one-tenth of this area has been explored in a practical and efficient way, and not over 1200 acres have been worked near and along the outcrops or edges of the coal. The practical mistakes which have been committed undoubtedly in a number of the mine-operations of the past, do not alone explain the unsatisfactory success and progress of the industry of this field ; nor can it be ascribed to the lack of local enterprise. Other reasons have to be looked for; and, as a principal one, the irregularity and the faulted conditions of the coal deposits must be pointed out. As a second cause, the indifference of the State government, which leaves the development of the field entirely to private enterprise, instead of aiding it by systematical and practical geological investigations, deserves to be mentioned. Nothing has been done by the State since the excellent work done more than fifty years ago by Professor Rogers, who could not at that time enter into the details of such

Jan 1, 1895

By Rudolf Bernhard

STATIC soil investigations with more or less heavy loads and extensive borings do not always have efficient results; also, they are very expensive. The new geophysical method of dynamic tests described herein is simple and cheap and avoids several disadvantages of the routine investigation, thus forming a useful supplement to the older methods and even at times replacing various static tests. The fundamental principle of dynamic soil tests consists in the appli-cation of artificial vibration. The technique employed is essentially geophysical in nature and in some respects is akin to seismic studies. Artificial vibration may be excited by centrifugal forces resulting from eccentrically supported rotating masses. The reactions of soil and structures caused by these vibrations may be measured. Their dynamic constants, such as amplitudes, phase speeds, damping, reflection, and interference effects, can be investigated. This geophysical method has been used for several years with increasing success. The results of these tests, summarized at the end of the paper, indicate that this method opens a new field for the practical engineer in investigating soils (capacity and formation), foundations, dams and structures, and especially buildings that must withstand earthquakes.

Jan 1, 1938

By Hallan N. Marsh

The subject of mud sounds so simple, uninteresting and unimportant that it has failed to receive the attention that it deserves, at least as applied to the drilling of oil wells. As a matter of fact, it is one of the most complicated, technical, important and interesting subjects in connection with rotary drilling. In 1923, R. E. Colloml said "It should be possible to establish certain physical standards for mud fluid," but while considerable work has probably been done on the subject before and since that time, and numerous articles have been written, the progress of general knowledge of the subject and the application of better practices have not kept pace with other developments in rotary drilling, and physical standards cannot be considered as established. Mud is apt to be thought of as an accessible and cheap material, but its cost is likely to be an important factor in the total cost of drilling a well. Some wells "make" most of their own mud out of the formations drilled, but in most cases a great deal of mud-making material has to be supplied from more or less distant sources. Expenditures for mud materials by one California company totaled practically one-quarter million dollars during 1929 and averaged about $13 per rig per drilling day, or about $2000 per well. Under unfavorable conditions, mud cost may reach many times this figure. Parker2 says that in the Hobbs, N. M., field "as much as $75,000 has been spent on one well alone for mud and mud-weighting compounds."' Presumably this is an exceptional case. Unit cost of mud fluid will range from 10 c. per barrel, where suitable material is close at hand, to $1 where crude material is available at moderate price but must be hauled long distances, and on up to as much as $11 per barrel where high gas pressure requires the use of special processed weighting material. The cost of mud pales into insignificance, however, when the results of using improper mud are considered. Blow-outs and lost circulation are obviously the result of inadequate mud. Stuck drill pipe, whether or not twisted off, in many if not most cases probably is caused by cuttings settling out of the mud or the mud itself precipitating. Recent experi-

Jan 1, 1931

By P. H. Wendland

Calculations are presented for the design of a silicon photodiode in which the incident light beam makes multiple passes between the detector surfaces. Total internal reflection is used for this "light-trapping" effect. By this means, the optical path length can be extended to several millimeters, while the electrode separation remains less than 102 cm, as required for nanosecond response time. Data are presented for a Schottky barrier photodiode constructed on a multiply reflecting silicon base wafer. It is shown that the long-wavelength response is considerably extended in such structures without a corresponding sacrifice in high-speed response. The development of efficient and powerful lasers at 1.06 p has stimulated interest in detectors which operate at this wavelength. In typical silicon photodiodes, for detecting 1.06 p radiation, the requirements for high speed and high sensitivity are mutually exclusive. Since the absorption coefficient is only 25 cm-', a lo-'-cm path length is required to absorb 92 pct of the incident 1.06 p radiation. If the electrode separation is greater than 10 cm, however, the carrier transit time will be greater than 1 nsec. This problem can be solved by allowing the incident light beam to make multiple passes between the electrodes. The optical path length can then be extended to several millimeters, as required for complete absorption, while the electrode separation remains less than 10' cm, as required for nanosecond response time. In a typical photodiode geometry, one ohmic contact and one rectifying contact are formed on the two opposite surfaces of a base wafer, and the wafer thickness determines the electrode separation. The objective of the multiple reflection design is to allow all 1.06 p radiation to enter the detector front surface and to form the back detector surface so that no 1.06 radiation can exit. Total internal reflection at the back detector surface is well-suited for light trapping of 1.06 p radiation because the relatively large dielectric constant of silicon leads to a critical angle of 16.5 deg for total internal reflection. LIGHT TRAPPING It is well-known that, as light passes from one medium such as air into another medium such as glass or silicon, the angle of refraction is always less than the angle of incidence. In the limiting case, where the incident rays approach an angle of 90 deg with the normal, the refracted rays approach a fixed angle +, beyond which no refraction is possible: this is called the critical angle. It follows from Snell's law that where = critical angle, n - index of refraction of air, n' - index of refraction of the medium. Applying the principle of reversibility of light rays, all internal angles of incidence greater than +, will produce total internal reflection and "light trapping". The index of refraction of silicon at 1.06 p is 3.5,' and the critical angle is thus 16.5 deg. Fig. 1 shows these relationships for silicon. This very small critical angle in silicon is significant because all incident angles between 16.5 and 90 deg will produce total internal reflection and "light trapping". This effect can be implemented with a "prismlike" geometry, so that incident light can be introduced into the sample without loss and "trapped". PHOTOSIGNALS A precise knowledge of the absorption coefficient at 1.06 in silicon is of critical importance to the design of fast and efficient silicon photodiodes for 1.06 radiation. Dash and newman2 show a value of 25 cm-l, and our measurements have corroborated this value. Assuming that the collection of photoinduced minority carriers is perfect, the quantum efficiency of a photodiode is dependent only on the absorption coefficient. It then follows from Lambert's law that where QE is the quantum efficiency in pct, a is the absorption coefficient, d is the optical path length, and the reflectivity at the surface is assumed to be completely suppressed by an optical interference layer. Fig. 2 gives the maximum quantum efficiency for 1.06p radiation of a silicon photodiode with optical path length d, using Eq. [2]. The ultimate response time of a fully depleted photodiode to an incident light pulse can be considered to be the arrival times of all photoinduced carriers at the contacts, i.e., the minority carriers at the junction interface and the majority carriers at the oppo-

Jan 1, 1968

By Nicholas J. Grant, Klaus M. Zwilsky

EVER since the unusual high temperature creep resistance and structure stability of SAP (Sintered Aluminum Powder) and similar aluminum-alumina alloys were reported,'," there has been a need to determine whether other metal-metal oxide (or other hard stable particle) alloys, not so ideal as the Al-Al 2 O 3 system, would show similar high temperature strength and stability. Of the many possible methods of obtaining a metal-metal oxide alloy,a one that offers many practical and theoretical advantages is the simple mechanical blending of metal powders with hard stable particles, followed by pressing, sintering, and hot extruding. With this purpose in mind copper powder and silica and alumina were selected for experimentation because these materials are readily available, cheap, reliable, and lend themseives te the simplest processing and testing. Starting Materials—Two sizes of electrolytically deposited copper powders were used, a —200 mesh powder referred to as A powder in this investigation and a —325 mesh powder referred to as C powder. Silica was added in the form of pure Potter's flint from which a —10µ fraction had been separated. Alumina of the a variety was used in two size ranges. The first was a —10µ fraction separated from a coarser aggregate, the second a commercial product of 0.3µ average diam manufactured by Linde Air Products. Preparation of Powders—Five-hundred gram batches of A copper with 1, 3, and 10 volume pct of each of the three oxides mentioned above were prepared, as well as C copper containing 1, 3, and 10 volume pct of —lop silica. Powders were weighed out carefully and blended by ball milling in air for 24 hr. Since this treatment resulted in surface oxidation of the copper, the charge was hydrogen reduced at 260°C for 5 hr. The next step consisted of hydrostatically compacting the powder into a shape suitable for the required hot working. For this purpose a slug about 11/2 in. in diam and 31/2 in. in length was produced by placing the mixed powders into a rubber sleeve, holding in a perforated steel canister, and rubber stoppering at the ends; the assembly was then subjected to a hydrostatic pressure of 50,000 psi. The air was evacuated from the assembly prior to pressing in order to prevent

Jan 1, 1958

By T. S. Lovering

Geochemical prospecting extends the age-old method of searching out lodes with a gold pan and rationalizes the prospector's hunch that certain plants are associated with ore. It uses sensitive but cheap and rapid analytical methods to find the diagnostic chemical variations related to hidden mineral deposits. Exploration geologists can gain tremendous assistance from this new tool, although its optimum use is not simple. To bring out the geochemical pattern that reveals the presence of a hidden ore deposit with a minimum number of samples requires a combination of shrewdness, chemical knowledge, and exploration geology. The use of sensitive analytical methods for prospecting had its start in the 1930's in northern Europe, where Scandinavian and Russian geologists had some success in these early efforts. Very little geochemical prospecting was carried on in the United States at this time, and no sustained interest was manifest until the close of World War II, when geochemical investigations were started by the Mineral Deposits Branch of the U. S. Geological Survey. The purpose of these investigations was to apply geochemical principles and techniques to surface exploration for mineral deposits. Both the research on analytical methods and the routine trace analyses for field investigations were at first conducted by a single group, but it later became apparent that the trace analyses could be done by men of less experience than that required for successful research on methods. For the past several years there have been two groups of chemists, and although their functions overlap, three of the chemists are chiefly concerned with research, while four to six other men make the trace analyses for field projects.

Oct 1, 1955

By Arthur Dwight

WE NOT have to go so very far back, when measured in actual years, to what may be considered the beginning of the industrial era of the great West, the discovery of gold in California in 1848, just 74 years ago. By a strange coincidence, this event occurred within a few days of the signing of the treaty with Mexico which ceded California to the United States. Needless to describe the mighty wave of humanity that hurled itself toward the setting sun in response to that call. The single thought in every one's mind was gold. The gold as they found it in placers or ledges could be so easily worked, and the product was so readily transportable, and available immediately as money, that practically no attention was paid to deposits of the base metals, in the treatment of which cheap transportation was a paramount con-sideration; consequently little progress was made in anything but gold mining until after the Civil War. The next great step was accomplished when East and West were united by the successful construction of the Union Pacific Railroad from Omaha across the great plains and through the Rockies to meet the rails of the Central Pacific coming eastward across the Sierras. The industrial history of our great West really dates from the day when those two hands of steel were joined, on the shores of the Great Salt Lake at Prom-ontory Point,. May 10, 1869. That seems a long time ago when we think of the enormous changes that have been wrought since that day, and when we regard the rich empire that has sprung up in that western land. Into the new empire thus made accessible, by this first thread of steam transportation, flocked a new brood of adventurous spirits from the older communities of the East. This way walked Fate; and as she, went, flung far the line of destiny, That bound an untracked continent to brotherhood from sea to sea; That long gray trail of dream and hope, marked mile by mile with graves that keep On every barren hill and slope some stout heart lost in dreamless sleep. Patience and faith and fortitude were willed to it and justified; Stern, homely virtues, plain and rude, eternal as the sky and wide. Nor ever sea-king dared the sea in sterner mood than these who went Strong armed to wrest from Mystery their birthright, half a continent.

Jan 4, 1922