Search Documents

By Winston A. Wong, John J. Jonas

Commercial purity aluminum was deformed by extrusion over the temperature range 320° to 616°C and the strain rate range 0.1 to 10 per sec. Flow stresses and strain rates were calculated from the experimenLa1 ram pressures and speeds. The stress-strain rate-lemperature relationship in extrusion was found to be similar to that in creep. Extrusion, torsion, compression, and creep data extending over ten orders of magnitude of strain rate and over two orders of magnitude of stress were correlated by a single creep equation. It was concluded that hot-working is a thermally activated process, in which the rate-controlling mechanism is either the climb of edge dislocations or [he motion of jogged screw dislocations. The microstructural changes observed during extrusion were consistent with the proposed deformation mechanisms. ALTHOUGH great progress has been made in understanding the technology of extrusion, very little is known about the actual deformation mechanisms operating during flow. Previous accounts describing extrusion have indicated that the relationship between ram speed (V), pressure (P), and temperature (T) can be given as follows:1 V = apb and P = A' exp(-AT). In these equations, a and b are constants which depend on temperature, A' is a constant which depends on ram speed, and A is a "coefficient" with a different value for each metal. Although these equations have fairly wide application, they do not contribute much to a fundamental understanding of the deformation. Furthermore, extrusion has not hitherto been considered as a thermally activated rate process. This lacuna is surprising because hot-working is similar to high-temperature creep in several respects. There is, in fact, a fair body of experimental evidence suggesting that the material response under hot-working conditions is similar to that occurring under creep conditions, in spite of the many orders of magnitude difference in strain rate.2"4 Since creep has been extensively analyzed in terms of dislocation mechanisms, the comparison of hot-working to creep is useful, for it can suggest the possible deformation mechanisms operating during hot-working. In this paper, the hot extrusion of aluminum will be examined from the point of view of thermally activated deformation mechanisms, such as operate during creep. EXPERIMENTAL PROCEDURE The experimental procedure consisted of extruding commercial purity aluminum* over a range of ram velocities and temperatures at constant die reduction by the direct method. Details of the experimental equipment have been published elsewhere.5 Extrusion was carried out at each of the following billet temperatures: 320°, 376°, 445°, 490°, 555°, and 616°C at the following constant ram speeds: 0.002, 0.008, 0.02, 0.1, and 0.2 in. per sec.* All results were obtained using a square-shouldered die with an extrusion ratio of 40:1, giving a reduction in area of 97.5 pct. The ram force was the dependent variable, and was measured by means of strain gages on the ram and was plotted as a function of ram travel. The sequence of events before making an extrusion was duplicated before each run so as to minimize as much as possible variations in experimental conditions. For example, after the equipment had been assembled, the billet was allowed to heat up to temperature inside the insulated container. Once the container attained the desired temperature, a period of 1/2 hr was allowed to elapse before the extrusion was made. This time was found to be required to allow the billet to reach a steady-state temperature, as determined from previous tests. When all was ready, extrusion was carried out without interruption; that is, the billet was upset and extruded in one operation. EXPERIMENTAL RESULTS AND DISCUSSION The two usual experimental approaches for investigating high-temperature deformation exhibit an important common feature. In the first approach, which corresponds to creep, a constant stress (or load) is applied to the material at constant temperature and the resultant strain is recorded against time. After an initial transient stage, a state of constant strain rate exists (secondary creep), in which a steady-state condition is established which is sensitive to variation in either applied stress or temperature. In the second approach, a constant strain rate is applied and the resultant flow stress is recorded. This corresponds to the situation in hot torsion or hot compression, where it is observed that, for a constant test temperature, there is an initial rise in stress to a steady value which is maintained up to very high strains. In tests of this type, a steady-state region is also established in which the stress is sensitive to variation in either the strain rate or the temperature.3,4,6-16 In both types of tests, therefore, a steady-state region is established after an initial transient. In the case of hot-working this region may be called steady-state hot-working, and it is analogous to steady-state creep with which it has many common features. Stress Dependence of the strain Rate in Extrusion. In order to assess the stress dependence of the strain rate under extrusion conditions, and to compare it to that of creep, as well as of hot torsion and hot compression, the extrusion data were analyzed according to power, exponential and hyperbolic sine creep equations.

Jan 1, 1969

By G. R. Speich, L. Zwell, H. A. Wriedt

HORNBOGEN1 has recently shown that it is possible to measure the degree of segregation accompanying cellular precipitation in ferritic Fe-Zn alloys by measuring the lattice parameter of the ferrite phase within the cell. In extending this work to study a wider range of composition and to evaluate the free-energy change accompanying the growth of the cells, the lattice parameter and the boundary of the a! phase in Fe-Zn alloys were redetermined to check the earlier work of Schramm.2 This appeared to be necessary since the Fe-Zn diagram has been drastically revised since the work of Schramm. Stadelmaier and Bridgers3 have recently shown that, contrary to prior belief: the y iron field is closed and the a phase boundary extends to an a + T + L peritectic at 782°C where peritectic a contains 42 at, pet Zn. The phase T in equilibrium with the a solid solution has a composition near Fe3Zn10 and a cubic 081 type structure.' The alloys were prepared by two different methods. In the first method carbonyl iron powder (400 mesh, 99.8 pet pure) and high-purity zinc powder (200 mesh, 99.99 pet pure) were mixed in a ball mill and then pressed in a die at 40,000 psi pressure to make compacts with a diameter of 5/8 in. and a thickness of l/4 in. These were sealed in evacuated quartz capsules, gradually heated to 1100°C over a period of 1 week (3 days at 600°C) 3 days at 800°C, 1 day at (1100°C), and then quenched in iced brine. For the alloys containing 23.4 and 30.1 at. pet Zn, the final homogenization anneals were performed at 1000" and 850°C) respectively, to prevent melting. In the second method, alloys were prepared by saturating high-purity iron millings (0.001 in. thick, 99.9 pet pure) in zinc vapor. For each alloy the impregnation was conducted at a fixed vapor pressure of zinc and a fixed temperature between 750' and 800°C. When saturated, the millings were quenched in water. The compositions of the alloys prepared by both methods are shown in Table I. The lattice parameters of the ferritic solid solutions were determined by comparing the 26 values of their 310, peaks (using Co Ka) or of their 211 , peaks (using Cr Ka) with those of corresponding peaks for high-purity a iron. The 20 values were measured at room temperature with an X-ray dif-fractometer (G.E.-XRD5). By using a fiducial value of 2.8664Å for the lattice parameter of pure a iron at 25oC,5 the lattice parameters of the zinc-bearing

Jan 1, 1964

By G. R. Love, M. L. Picklesimer

Aboue 950°C the Nb-Zr system consists of a completely miscible bcc solid solution, commonly called the phase. Between 950 and 600°C, and between 20 and 85 pct Nb, the phase deconlposes, after sunciently long times, into two bcc solid solutions. The pct Zr alloys are conveniently descibecl with T-T-T (time-temperature-transformation) curves having a nose at about 2 hr at 700°C. The reaction rate varies only slowly with zirconium content and negligibly with oxygen contanzination; it is speeded up by a factor of 10 to 15 by 90 pct cold ulork and slowed dou by n factor oj 10 to 30 by a two-hundrecljold increase in grain size. Nb-r alloys with compositions between 40 and 85 pct Nb have been the basis for the majority of commercially important superconducting materials. In part because of their commercial promise, more is known about these alloys than about most other high-field superconducting materials. At the same time, there is considerable disputed or incomplete metallurgical information. For example, although Rogers and tkins&apos; indicate a monotectoid reaction at approximately 600°C and a two-phase 01 + 0, field extending between 20 and 85 pct Nb and to a maximum of 95OGC, erhout&apos; has reported that this entire region would be a single homogeneous B were it not for oxygen contamination. Again, although it has been shown that relatively short-time heat treatments in the vicinity of 700CZ significantly improve the ability of short wire samples to carry high currents in high magnetic fields at 4.2K, these observations have never been fully correlated with the structural change or changes occurring during the anneal. We intend to investigate in detail the effect of metallurgical variables, including heat treatment, on the superconducting properties of hard superconductors. To verify that our experimental techniques are valid and to establish a relative standard against which other materials may be measured, we feel it advisable to know the behavior of the Nb-Zr alloys under a variety of processing conditions. As an initial step toward this goal, we have determined in detail the kinetics of the transformations in Nb-Zr alloys. EXPERIMENT A number of problems had to be solved before beginning any fruitful work on the reaction kinetics in this system. While solving some of these problems, either by chance or by design, small amounts of information were obtained about alloys containing 40, 50, 60, 65, 67, 70, and 75 pct Nb, bal. Zr. In addition, a large range of grain sizes and a range of temperatures considerably greater than the range indicated by Rogers and Atkins phase diagram were examined. We will, however, report in detail only the results obtained for the Nb + 33 pct Zr and Nb + 25 pct Zr alloys at three grain sizes, two levels of oxygen contamination, and the temperature range 550 to 950°C. These data are most complete, but the other data are sufficiently complete to indicate the kind and magnitude of the variation of the transformation kinetics outside this range. The first and most difficult problem encountered in this inquiry was one of sample homogeneity. When Nb-Zr alloys are arc- or electron-beam-melted on a cooled copper hearth, solidification is sufficiently slow that there is appreciable coring in the cast structure and a large variation of grain size across the button thickness. Both these factors significantly affect the apparent reaction rate in the system. A two-step solution to the problem was attempted; an arc-melting and drop-casting technique has been developed by conald that greatly reduces the as-cast grain size and virtually eliminates coring segregation. Ingots made in this way exhibited no detectable (3 pct maximum) zirconium segregation. Before it was evident just how good this technique was, we attempted to supplement it with rather long-time, high-temperature annealing of the cast ingots. This annealing was carried out in evacuated and sealed (seal-off pressures < 1.0 x 106 torr) quartz capsules lined with tantalum foil at 1400 to 1450 C for 8 to 72 hr. There were two principal effects of this treatment: the grain size increased to a fairly uniform 150 p, and the surface and all grain boundaries near the surface acquired a film of a second phase, tentatively identified as an oxide (possibly additionally contaminated with silicon). There was no evidence that this 1400 C treatment had affected the zirconium segregation. High-temperature annealing was subsequently used only for grain-size control, but anneals of longer than 4 hr at temperatures greater than 1000°C were performed in dynamic vacuums (pressure no greater than 1.0 x lo torr). Any contamination resulting from these treatments was well below the limits of detection of our techniques. All samples, as cast, were cold-swaged to at least 85 pct reduction in area. The samples called cold-worked were tested as swaged. The minimum re-crystallization anneal for these alloys was about 12 hr at 1050 C; this produced an equiaxed grain diameter of about 4 to 8 P. Annealing for 4 hr at 1450°C produced a grain size of about 80 to 150 p; and annealing for 4 hr at 1650aC, close to the melting point of many of these alloys, produced a grain size of 0.5 to 1.0 mm. At all temperatures, the larger grain size was

Jan 1, 1967

By L. Bombardieri, H. F. Mills

IRON KING mine, producing gold-silver-lead-zinc ore, is 10 miles east of Prescott, Ariz. At present the 1806 level is being developed. The echelon pattern of ore deposit continues at depth but is less pronounced, and the orebody is now more or less continuous over 2600 ft of strike length. with widths 5 ft to as high as 26 ft where overlapping of lenses occurs in one section of the mine. Better continuity of ore at depth has encouraged systematic mining and improved plant facilities to offset higher operating costs. With favorable persistence of ore at depth. the three-compartment No. 6 hoisting shaft appeared inadequate to handle increased tonnage from greater depths, and in 1952, a four-compartment steel and concrete shaft was started. This is now at a depth of 1906 ft, and shaft pockets and loading cartridges are being installed on the 1806 level. Ore from the new shaft, hoisted in 51/2 -ton Jeto bottom dump skips, is dumped into a 500-ton shaft bin, from which it is fed to a 16x30-in. gyratory crusher and conveyed 415 ft through an undersurface concrete gallery to the secondary crusher and conveying system supplying the 900-ton mill. Lead, zinc, and pyrite concentrates are floated, and the flotation tailings are cyanided after desliming. Waste from the new shaft is dumped into a 250-ton surge bin, fed from this bin to a 24-in. conveyor, and discharged into the glory hole above the block cave. The new shaft is served by a double-drum 400-hp hoist used for ore and waste; the No. 6 shaft conveys men and material To secure a cheap source of waste fill for stoping operations, a block cave area was undercut In the hanging wall near the north end of the mine above the 600 level. Waste from the block cave is drawn from any of three large drawpoints on the 600 level, and a series of hanging wall transfer raises with controls and bypasses on each level provide a fast low-cost material for fill. The block cave is worked vertically through to surface in the form of a steep-sided hole 350x250 ft and several hundred feet deep, the sides of which cave and provide fill material without any blasting. Fill is a mixture of caliche-cemented surface gravel and small particles of hanging wall schist. Level Development: An orebody 300 times as long as it is wide requires a lot of development work. Former practice consisted of driving a haulage drift about 30 ft from the ore in an andesitic footwall, a drift on the ore, and crosscuts from the haulage drift at 100-ft intervals. Crosscuts are about 90 ft long. At present, only the odd numbered levels are so developed, and on the even numbered levels only the haulage drift and crosscuts are driven. Little or no timber is used for this development. This change resulted in 20 pct reduction of development costs and 50 pet reduction of square set stoping required for removal of floor pillars. Elimination of ore drifts on alternate levels leaves

Jan 1, 1957

By J. D. Hanawalt, W. H. Gross

Magnesium has long been known as the lightest of our engineering metals. This metal, silvery white in color, has a specific gravity of only 1.74. Aluminum, the next lightest structural metal, is 1 ½ times heavier; zinc is 4 times heavier; iron and steel are 4 ½ times heavier; and copper and nickel are 5 times heavier. Magnesium does not occur in the free state but is very abundant in nature, constituting 2.5 pct of the earth&apos;s crust in the form of various ores. It is the third most abundant structural metal, being exceeded only by iron and aluminum. Magnesium is unique, however, in that in the form of magnesium chloride it also exists in the oceans. Sea water is the source most widely used for production in the United States but magnesium is also commercially produced from magnesite, dolomite, and other ores as well as from certain inland brines. The vast quantity of magnesium existing in the waters of the oceans can be visualized when it is realized that the removal of one hundred million tons per year (the approximate annual steel production in the United States) for a million years would reduce the magnesium content of sea water only from 0.13 to 0.12 pct, providing no more magnesium had washed into the sea in the meantime. Not only is magnesium potentially very abundant but it is in addition a very versatile metal and can be shaped and worked by practically all methods known to the art of metal working. It can be cast by sand, die, and the various permanent-mold methods;

Jan 1, 1953

By Robert M. Grogan, James C. Bradbury

The Illinois-Kentucky mining district has, since 1880, accounted for 80 per cent of all U.S. production of fluorspar. The ore deposits are of two types: vein deposits formed by fissure fillings along faults and bedding-replacement deposits formed by the replacement of strata at certain favored stratigraphic positions along minor faults and fractures. Fluorite is the chief valuable mineral in the deposits. Sphalerite and galena commonly are present in small amounts but, in some ore bodies, may form a substantial part of the valuable constituents of the ore. Calcite is the chief gangue mineral; quartz and barite Exposed strata range from Devonian are present in various amounts. through Pennsylvanian in age. Igneous intrusive rocks occur as mafic dikes and sills and intrusive breccia dikes and plugs. Structurally, the district is situated on a generally northwest- trending arch that has been sliced into a series of long, narrow blocks by normal faults that trend northeastward. The structural The localization of the ore deposits by faults and fractures, the association of fluorite mineralization with intrusive breccias, and various lines of petrographic and geochemical evidence indicate that the fluorite-zinc-lead deposits were epigenetic and deposited by solutions emanating from a deep alkalic magma.

Jan 1, 1968

In 1973, US Borax & Chemical Corp. began investing three days wages and about $20 in training materials in every new employee before having him report to his first job. The result? Accidents involving new employees in the past two years have dropped by more than half from the 1972 level. What made this success possible was safety training done with programmed instruction materials-which, incidentally, US Borax also uses for vocational training.

Jan 4, 1976

By S. H. Ash, J. J. Forbes

Probably the newest thing in mining safety, or safety for mines, is the apparent dissatisfaction on the part of the mineral industries, as represented by both management and labor, and the general public of the Nation, with the safety record of the mining industry. This is reflected by published comments and papers in the technical press;l-9 in labor periodicals,10,11 in popular journals and periodicals,l2, 13 and in the daily press; also by discussions of the Safety Committees sponsored by the National Safety Council,9, 14-15 the American Mining Congress,l.l6 the American Institute of Mining and Metallurgical Engineers,2,4 the Mine Inspectors&apos; Institute of Amerthe Coal Mining Institute of America,5 19 the American Standards Association, and others.20.21 Mining safety is a joint problem of management and the individual workman. Safety is not attained and will not be attained solely by laws, decrees, and commands because, if it could be done in this manner, acceptable mining safety would have been achieved long ago by the individual states in our Nation and by the nations abroad. The best safety performance is found at plants where management provides a safe environment for the workers; where supervision is efficient and super- visors, others concerned with promoting safety, and the individual worker know through training, experience, and personal contact the safe and unsafe practices of their field; and where the trained individual worker has become safety-minded by experience, quiet influence, unconscious suggestion, and personal guidance. Despite what may be said to the contrary, progress has been and is being made in mining safety. This is shown in Fig 1 to 4. It is beyond the scope of this paper to give possible reasons for the valleys and peaks in the fatal-injury rates. Some recent factors that appear to be contributing to the improvement in these rates are briefly discussed. Aside from mining equipment, "what&apos;s new in mining safety" for some mines has been in effect or was tried by others long ago. A safety pro- gram is a living thing; as such, it must be vitalized and continuously fed with enthusiasm, constructive action, and improvements. Because safety is concerned with human conduct, it is necessary to practice safety at all times; if not, it is soon forgotten, and accidents occur. Mining-safety Records The large employment and production concerned with anthracite contribute much to the mining-safety records of the mineral industry. Approximately 81,000 persons are. employed in this industry having mines concentrated in an area of 480 square miles in northeastern Pennsylvania. Because of the achievement of the anthracite industry in safety during 1948, the other branches of the mineral industry can profit by a study of what has been done to achieve that record. Where one mineral is produced by other large groups having methods of mining that are similar in many respects to the anthracite-mining methods, an achievement in such a large industry is important. Salient factors concerned with safetye in the anthracite industry are: no radical change has occurred in the mining-safety regulations pertaining to anthracite mines. Because anthracite mining is a branch of the coal-mining industry,

Jan 1, 1950

By Robert Baker

IT has been demonstrated in the laboratory by A. J. Phillips1 that a transformation or conversion from beta directly to alpha may take place in a brass of 61 to 62.5 per cent copper content. The completion of the transformation is dependent on a rapid rate of cooling from the all-beta field through the alpha + beta range to the alpha field. Phillips states that in a slowly cooled alloy containing 62 per cent copper and 38 per cent zinc the copper content of the beta is progressively decreased from 62 to 56 per cent by precipitation of alpha. Rapid cooling tends to prevent the separation of alpha with a copper content of more than 62 per cent by reducing to a minimum the time required for passing through the alpha + beta range. Upon crossing beyond the (alpha + beta.)/(alpha) boundary to the all-alpha region below, the material is transformed from beta to alpha. It is essential that there be no change in composition. Phillips obtained his results by quenching a 62:38 copper-zinc alloy from 850° C. in iced brine at -8° C. No reference to the occurrence of this transformation in a manufacturing process has been found in the literature. An investigation of the microstructures of a number of hot forgings made from leaded brass rods yielded one forging in which this striking conversion from beta to alpha had occurred. The purpose of this paper is to describe the transformation and certain conditions under which it may occur during the hot pressing of brass. The conversion was noted in a shape forged from a leaded brass rod, the composition of which was: Cu, 60.26 per cent; Zn, 37.86; Pb, 1.88. In this study the lead content was disregarded and the alloy was considered to be equivalent to an alloy of 61.40 per cent copper and 38.60 per cent zinc (98.12 parts = 100 parts). The possibility that the lead might obstruct or accelerate the precipitation of alpha was not studied. The lead appears as black globules in the photomicrographs and has a negligible solubility in the alloy.

Jan 1, 1931

By AIME AIME

CERTAINLY in point of attendance, and doubtless in several other ways as well, the 147th meeting of the A.I.M.E. was the best ever held. In times of depression, mining engineers and metallurgists have plenty of time to come to the Annual Meeting but money is scarce; at the height of industrial activity they have plenty of money but no time. "The current period of transition seemed to provide ideal conditions for&apos; both the preparation of papers and attendance at their presentation. The weather made even the Californians present envious though the weather man gets no credit, for rain and snow was what he willed. Among the elevator men, the miners have the reputation of being the toughest crowd to handle, though the best natured, withal, of all the engineering groups that meet in the Engineering Societies Building. This year Your inquiring reporter was told, "it was the damnedest meeting I ever saw; they

Jan 1, 1937

By H.E. Brauer

Among the zinc base alloys used for casting in metal moulds, pnrticularly die casting, those alloys containing aluminum usually together with copper, are probably the most widely used. The reason lies in their desirable mechanical properties and the fluidity and absence of hot shortncss which facilitate ca,sting. Objection to the use of these alloys may be raised on account of the rather frequent instances of failure of a type variously described as disintegration, exfoliation and intererystalline corrosion. In all cases which have come to our kno~vlcdge where the conditionsof service were known, failure has occurred upon cxposurc to moisture and heat varying from a hot moist atmosphere to lligh pressure steam. RIoreover, the alloys described in all such roses contain impurities or alloying metals which the present authors have found to have enormous accelerating effects on intererystalline oxid:~t&apos;ion in zinc-aluminurn alloys. Thus Williams1 experimented with an alloy containing a large percentage of tin exposed in Cuba. Baucr2 reports failure of a boiler plug containing over 1 per cent. of impurities, doubtless lead for the must part, and Rawdon&apos;s3 examinations were madc on an alloy containing 0.1 per cent. lead also exyosctl to thc Tropics. No thorough investigation of the nature and cause of this type of failure has been made heretofore, so far as the authors are aware, although Rawdon correctly classified it as internal oxidation. We have, therefore, carried out this investigation in order to det&apos;ermine the exact nature of this phenonienon and the effect of other metals present as impurities or intentional additions in accelerating or retarding it. In the appendix we include a considerable amount of data which may be valuable in selecting an alloy combining good physical properties with high resistance to oxidation. At the time this work was undertaken the best available equilibrium *Investigator, Metal Section, Research Division, The New Jersey Zinc Company. &apos;H. W. Williams—Jour. Am. Inst. of AIet,als, Vol. 11, p. 221 (1917). 2o. Bauer—ZeiL, fiir i&apos;vletall Kunde, Vol. 12, .No. 7, pp. 129-31 (1920). 3H. S. Rawdon—Trans. Am. Elcctrochcmic.al Society (1921).

Jan 1, 1923

By H. E. Brauer

Among the zinc base alloys used for casting in metal moulds, pnrticularly die casting, those alloys containing aluminum usually together with copper, are probably the most widely used. The reason lies in their desirable mechanical properties and the fluidity and absence of hot shortncss which facilitate ca,sting. Objection to the use of these alloys may be raised on account of the rather frequent instances of failure of a type variously described as disintegration, exfoliation and intererystalline corrosion. In all cases which have come to our kno~vlcdge where the conditionsof service were known, failure has occurred upon cxposurc to moisture and heat varying from a hot moist atmosphere to lligh pressure steam. RIoreover, the alloys described in all such roses contain impurities or alloying metals which the present authors have found to have enormous accelerating effects on intererystalline oxid:~t&apos;ion in zinc-aluminurn alloys. Thus Williams1 experimented with an alloy containing a large percentage of tin exposed in Cuba. Baucr2 reports failure of a boiler plug containing over 1 per cent. of impurities, doubtless lead for the must part, and Rawdon&apos;s3 examinations were madc on an alloy containing 0.1 per cent. lead also exyosctl to thc Tropics. No thorough investigation of the nature and cause of this type of failure has been made heretofore, so far as the authors are aware, although Rawdon correctly classified it as internal oxidation. We have, therefore, carried out this investigation in order to det&apos;ermine the exact nature of this phenonienon and the effect of other metals present as impurities or intentional additions in accelerating or retarding it. In the appendix we include a considerable amount of data which may be valuable in selecting an alloy combining good physical properties with high resistance to oxidation. At the time this work was undertaken the best available equilibrium *Investigator, Metal Section, Research Division, The New Jersey Zinc Company. &apos;H. W. Williams—Jour. Am. Inst. of AIet,als, Vol. 11, p. 221 (1917). 2o. Bauer—ZeiL, fiir i&apos;vletall Kunde, Vol. 12, .No. 7, pp. 129-31 (1920). 3H. S. Rawdon—Trans. Am. Elcctrochcmic.al Society (1921).

Jan 1, 1923

By Herty, C. H.

Iron oxide (FeO) plays an extremely important part in the manufacture of iron and steel. In the three major processes- blast-furnace, open-hearth, and Bessemer converter-iron oxide is the chemically predominant compound and controls to a large ex- tent the operation of the furnaces and the composition and quality of their respective products. In order to emphasize the importance of iron oxide in each process, they will be considered individually in some detail. THE OPEN-HEARTH FURNACE. Iron oxide is introduced into the open-hearth furnace in four ways : 1. The scrap charged into the open hearth is oxidized by the furnace gases, the amount of oxide formed depending primarily on the amount and type of scrap charged. It has been found&apos; that with large scrap, 1.7 Ib. of FeO is formed per 100 Ib. of scrap charged, whereas with scrap of medium size about 5.3 Ib. of FeO is formed per 100 Ib. of scrap charged, when the period between the charging of the scrap and the addition of hot metal is 3 hours. 2. The decomposition of the limestone sets free CO, by the reaction

Jan 1, 1957

By W. McDermott

It is well known that many so-called free-milling silver arcs are so classed more from their value necessitating a cheap process than from a real adaptability to raw amalgamation. Such low--grade ores, carrying more or less sulphurets, are more profitably treated by a cheap rapid process than by the more effective but costly process of roasting arid amalgamation. The tailings are sometimes crudely concentrated, or, after lying and becoming partially oxidized, are again worked in pans. Of late years, by the use of improved methods of concentration, many old low-grade tailings-piles have been reworked to a good profit; and in some improved mills arrangements are made to concentrate before or after amalgamation, thus making a single treatment in mill suffice. It is self-evident that on a low-grade ore a small increase in percentage saved is of no commercial advantage if accompanied by a material increase in cost, and therefore a cheap and continuous system of work is the real necessity, if a fair saving be effected. As an illustration of the possibilities of combined concentration and amalgamation on some ores, the following results of a working test at the New York Ore-Milling and Testing Works will be of some interest. The ore treated was a hard white quartz from Mexico, carrying a very small percentage of finely divided sulphurets, chiefly iron

Jan 1, 1885

Jan 1, 1891

By Ellsworth Daggett

In the first paper on the Russell process presented by Mr. Stetefeldt, in May, 1884 (Transactions, xiii.), the process was treated from a purely theoretical standpoint.. 111 his second paper of October, 1886 (Transactions, xv,), the details of the plant, the chemicals used, and the manipulation in both mill and laboratory were treated. The aim of the present paper is to present economical results recently attained, new data affecting the preparation and manipulation of ore in the mill, and a more complete and systematic scheme of laboratory work. This paper is compiled mainly from Mr. Russell&apos;s notes of his own experience. Many of these notes, particularly those relating to work at Cusihuiriachic,* Mexico, have been upon work directly under the personal observation of the compiler, who takes pleasure in thus presenting to the Institute, data and considerations of much interest and value pot only to users of the Russell process, but to mill men generally. The description of the chemicals used and of the preparation of the mill-solutions being&apos; in part the same now as when Mr. Stetefeldt&apos;s second paper was published, some use is here made of portions of that paper. No theoretical matter is here given. For a treatise containing also the theory of the process the reader is referred to Mr. Stetefeldt&apos;s complete work on " Lixiviation of Silver Ores by Hyposulphite Solutions," now in preparation. To facilitate the consultation of this paper, the following synopsis and index is prefixed. The figures in parenthesis indicate the page of this paper on which the subject is treated.

Jan 1, 1888

By Gerald C. Dohm

INTRODUCTION After a mining company has discovered a mineral deposit, the problem is then how to mine and process that deposit the best way. The principal problem facing managers or engineers who must decide on mine plant size, equipment selection, and long-range scheduling is how one can optimize a property not only in terms of efficiency but also as to project duration. Mine opti¬mization is dependent upon the interaction of con¬tributing parameters which leads to maximizing the net present value (NPV) Realistic mine planning is the key, to the analysis. The process is to be used when evaluating undeveloped properties or when a complete revamping of existing facilities is scheduled The proc¬ess is not intended for detailed mine design but rather for property evaluation and feasibility studies. The derivation of the various input parameters will only be discussed to the point where a meaningful correlation can be made with the overall analysis. The interrelationship of the parameters will be the central point because most company guidelines and financial analysts have their own standards when deriving the various inputs. Assume that the data is totally acceptable and pro¬vides at least the following categories of information and guidelines- (1) mineral and waste inventory; (2) geologic, hydrologic, and geotechnical criteria; (3) topographic layout including property boundaries; (4) metallurgical flowsheet, recovery and design criteria; (5) access, water, power, and environmental base-line study; and (6) financial constraints (minimum rate of return, payback period, etc).

Jan 1, 1979

By A. W. Fahrenwald

FLOTATION practice in Idaho is now about 13 years old. The advance has been steady during these 13 years. The operators have been alert to take advantage of the newest developments and they have themselves made a constant effort to improve their work. The metallurgical improvements are due to the development of (1) better equipment, (2) better reagents, and (3) better understanding and control of the process. During the eight years the writer has been in this district, there has been continuous experimentation by several companies to improve the ore dressing by flotation methods. Gravity concentration has fought hard to hold its place, and although it is true that gravity processes have been improved during this period, nevertheless, in several of the important mills of the district the few tables that managed to hang on have finally given way. On the straight-lead ores, tables and jigs are still used; and, due to better classification, their hold on this job has been strengthened. ORES OF THE DISTRICT The ores of the district are of two general classes: (1) clean lead ores, such as those from the Bunker Hill and Hecla mines, and (2) complex lead-zinc ores. The general impression prevails that the clean lead ores, class 1, are simple and that it is easy to obtain high recoveries and good grade products. This, in a way, is a false impression; there is quite a high percentage of locked middling in these ores at 100 and 150-mesh sizes. Improved classification preparatory to table treatment of this type of ore has made it possible to segregate effectively a high-grade middling which is further comminuted and floated. The complex lead-zinc ores of the district, of which the ore from the Morning mine of the Federal Mining & Smelting Co. is a typical example, always have presented a difficult problem. It always has been comparatively easy to make a clean lead concentrate, but it never has been possible to concentrate sphalerite with a-specific gravity of 4.10 from siderite of gravity 3.88. Also, a large percentage of the galena and sphalerite of this class of ore refuses to separate out until the crushing has been carried

Jan 1, 1928

G. A. Moore—The tin-fusion method has been a very favorable possibility for many years. The authors apparently have settled the question that delayed the method for a long time by showing that no hydrogen is absorbed in the tin. This, of course, is very important. I want to make a few remarks concerning the absolute accuracy of analysis, which must be the final basis for deciding among the various methods. From the figures in the paper, there seems to be some re-maining slight discrepancy on the actual amount of hydrogen present in various samples which may be presumed essentially identical. (This is of the order of the precision of individual analyses but appears in averaged results.) From the analyst&apos;s viewpoint, the tally of hydrogen content can be regarded as occurring in three portions. First is a large portion which comes off easily and automatically during sample storage and later on heating in the apparatus. This is fairly easily analyzed. Second is an item which may be either positive or negative in the tally sheet. In warm or hot evolution, this is a portion which, in practice, can never be re-

Jan 1, 1951

By R. J. Grissom

PHOSPHATE deposits have been worked in many countries of central and south central Tennessee, but only ht ebrown rock deposits of Maury and Giles Counties will be discussed at any length in this articles, as all of the major opeations are now located there. They are: Mt. Pleasant District-Federal Chemical Co., Hoover and Mason Phosphae Co., International Minerals and Chemical Corp. (Maury and Giles Counties), Virginia-Carolina Chemical Corp. (formerly Charleston Mining Co.), and Victor Chemical Co. Columbia District-Armour Fertilizer Works and Monsanto Chemical Co. In the near future, the well-known, extensive deposits of blue rock in Lewis and Hickman Counties,also the brown rock in Hickman, Willamson, Summer and Davidson Counties, will again come into production. Certain physical peculiarities of the Tenessee deposit have played an important part in the design and use of mining and milling equipment.

Jan 1, 1944