Search Documents

By Michael Windhager

UltimaTM rolls have been designed for intermediate and finishing stands of rod and bar and small and medium section mills. The rolls and rings are spun cast, with a highly alloyed working layer and a tough nodular iron core. Microstructure and hardness level can be adjusted over a wide range, which allows us to adapt the rolls to differing rolling conditions. After introducing the UltimaTM concept, this paper will describe the results of UltimaTM rolls achieved in various mill applications, like finish rolling of rebar, and slitting. Special emphasis is given to performance gains when using UltimaTM rolls, compared to standard rolls. This paper also examines the impact of UltimaTM rolls on mill and roll shop productivity.

Jul 30, 2018

By Salete Martins Alves

The future lubricants must be more environmentally adapted, with a higher level of performance lower total life cycle, cost than currently used lubricants. Environmental friendly, the biodegradable alternatives are available for a large variety of mineral oil based lubricants. Vegetable oils are the major source of these base fluids, although they have lower thermal and oxidation stability and even worse low-temperature behavior than mineral oil. These physical and chemical properties can be improved by chemical modification. The aim of this study was to evaluate physicochemical properties and film formation from modified vegetable oils. The vegetable oil was chemically modified by epoxidation reaction with acetic and formic acid using sunflower oils. Viscosity, iodine value, density, acidity value and thermal stability were determined for epoxidized oils. The film formation was analyzed using a HFRR tribometer. The results showed that epoxidized vegetable oils had excellent properties to be used as lubricant, and their tribological performance is higher than mineral oil.

Jul 31, 2018

By Piotr Kula

Vacuum carburising with pre-nitriding (PreNitLPC® technology) involves feeding ammonia during the charge heating stage before carburising. The purpose is to restrict the growth of grain in the surface layer of the carburised steel. The article presents the influence of nitrogen on restricting austenite grain growth during vacuum carburising and on mechanical properties (fatigue strength, impact resistance) of layers that underwent such treatment in comparison with traditional carburising methods.

Aug 16, 2017

By Patrícia Mundim Campos Faria

The process of particle size reduction by grinding is inherently inefficient and involves high capital and operating costs. In particular, ball milling is one of the important unit operations in the iron ore pelletizing process. The mill product, due to its physical properties, determines the efficiency of subsequent stages of classification, filtration and pelletizing, thus impacting the quality of iron ore pellets. The work demonstrates the application of the population balance model in the optimization of a full-scale ball mil circuit grinding pellet fines with the aim to evaluate the optimal solids concentration to improve iron ore pellet quality. Initially, detailed experimentation was carried out in a 25.4 cm diameter batch mill and a relationship for mill scale-up using a linear population balance model in wet grinding systems was established. The selection and breakage parameters and the specific selection functions were determined for pellet feed iron ore. It was possible to identify the non-normalizable nature of the breakage functions of the ore studied, which were modeled properly. Afterwards, as a result of incorporating the specific selection functions and breakage functions into the linear population balance model, it was possible to predict product size distributions in the pilot and plant scale mills (0.416 and 5.18 m diameter, respectively) from data obtained in the 25.4 cm diameter mill. Finally, with this scale-up procedure it was possible to appraise the plant scale optimization via laboratory scale grinding mill tests. The effects of changing percent solids were assessed in order to improve the industrial mill performance and the optimal value should be in the range from 76 to 80%.

Aug 1, 2018

By Moisés Paulo Teixeira

The use of tailings for the synthesis of new materials is a worldwide concern today. This paper approaches the utilization of tailings of soapstone (steatite) in order to produce ceramics. The results show that the addition of soapstone in a ratio over 20% in the ceramic mass has enhanced the bending resistance of the ceramic samples when they were fired at temperatures of 900°C or 1000°C.

Oct 30, 2017

By Manfred Hackl, Sergey Bragin, Alois Seilinger

The demand for hot rolled strip is growing in multiple ways. To remain competitive, new and existing mills must meet arisen challenges in the best possible way. The production of hot strip is a key element of steel production. Since close to half of all steel produced is hot-rolled to strip, mills require maximum throughput and availability combined with geometrical precision and the ability to create optimum material properties. Today there is a clear trend in developing new steel grades with high-strength and improved formability, like 3rd generation AHSS (Advanced High Strength Steels), as well as a trend to produce thinner and wider gauges. This trend challenges hot strip mills because it requires new technologies which provide more flexibility in metallurgical treatment during the rolling process. In order to meet and promote these trends Primetals Technologies is currently working on different concepts and solutions. One example is the development of a new mill stand technology Flex-HI HOT which allows to adapt the last finishing mill stands by efficiently switching from 4-high to a 6-high mode with small work roll diameter based on production needs. Another solution is to apply a permanent 6-high rolling stand at the end of the finishing train. A smaller work roll diameter allows to achieve higher specific thickness reductions and deformation rates resulting in significant thinner hot-strip gauges with valuable metallurgical benefits. The developed solution concepts with technological and metallurgical benefits will be presented in this paper.

Oct 1, 2019

By Jorge Magalhães Ávila de Paula

A aplicação de materiais metálicos exige que os mesmos sejam submetidos a etapas de conformação mecânica. Estes procedimentos elevam significativamente a densidade de descontinuidades, alterando a morfologia dos grãos, assim como o estado de tensão induzida na estrutura. Os materiais submetidos a processos de conformação, em especial aos de conformação a frio, são submetidos, após a deformação, a um tratamento térmico denominado de recozimento de recristalização, cujo objetivo é recuperar a estrutura e recristalizar os grãos. Neste contexto, estudou-se a viabilidade de aplicação da técnica de calorimetria diferencial (DSC), como ferramenta para a determinação da temperatura de início de recristalização de aços. Para a execução deste trabalho, foram utilizados amostras de aço SAE1010 que foram deformadas a frio e em seguida submetidas a rampas de aquecimento em um equipamento DSC. A técnica de DSC evidenciou apenas o início do fenômeno de recuperação do material. Algumas amostras deformadas foram submetidas a tratamentos térmicos de recozimento de recristalização a 500°C, 600°C e 700°C. A partir da caracterização microestrutural e de ensaios de microdureza, calculou-se os valores de k e n do modelo de Avrami para as amostras tratadas a 600°C e 700°C, obtendo-se após isto a energia de ativação para as deformações de 69,6% (199,5KJ) e 87% (178,4KJ). À 500°C, as amostras não se recristalizaram, confirmando esta temperatura abaixo da crítica para as deformações estudadas.

Aug 16, 2017

By Cyro Takano

A degradação durante o processo de redução de minérios de ferro é bastante conhecida pelos fenômenos de crepitação e inchamento. Em aglomerados a frio, auto-redutores utilizando cimento como aglomerante, há também degradação pela decomposição de hidratos que conferem resistência a frio, além de aumentar os vazios deixados pelo consumo do redutor. Outro fenômeno que afeta na velocidade da reação de redução é a formação de escória. Esses aspectos são analisados neste trabalho e principalmente em processos de auto-redução.

Oct 30, 2017

By Klaydison Silva, Maurício Curi Segato, Elves Matiolo, Neymayer Pereira Lima

Flotation is the main concentration process, has been applied with sucess for the removal of quartz on the iron ore industry aiming high quality concentrates. limiting the top size close to 0,300mm and the removal of slimes are fundamental for the efficiency of reverse flotation of quartz. The high consumption of reagents, leading to insufficient particle coverage, and increased foam stability, leading to the difficulty of removal of quartz particles, are the main deleterious effects of the presence of slimes. Recent characterization studies, together with the development of new collector of linear chain, allowed the obtaining of concentrate with SiO2 contents close to 3% with 94% of metallurgical recovery, based on pilot tests carried out on a sample flotation column of the Quadrilátero Ferrífero.

Oct 3, 2019

By Roberto Balarini Junior

Tribological behavior of Si3N4 balls sliding against Al2O3 discs in water was investigated by studying the influence of parameters such as initial surface roughness and circular axial run-out of the discs. The objective was to relate these parameters with the occurrence of the phenomenon known as ultra-low friction coefficient (ULFC), which is characterized by µ < 0.01, including the correlation with running-in duration. As a general trend, greater initial surface roughness and circular axial run-out resulted in greater running-in duration. In addition, it was verified that a mixed lubrication regime (hydrodynamic and boundary) is required to guarantee the occurrence of ULFC by comparing the calculated minimum film thickness with the composite roughness of the worn surfaces. Also, ICQ-OES analysis of the water after the tests indicated that a silicon concentration greater than 1.3 mg/l should be fundamental for the occurrence of µ < 0.01.

Jul 31, 2018

By Marjorie Benegra

This study aims to compare the wear resistance assessed in rubber wheel abrasion test of nickel aluminide coatings deposited by for Plasma Transferred Arc (PTA) and High Velocity Oxigen Fuel (HVOF) manufacturing, using the same raw material. A nickel aluminide powder was atomized and deposited on 316L steel plate substrate. After deposition, some specimens were submitted to a heat treating (1200 °C for 24 h followed by 760°C for 24 h). The coatings deposited using PTA developed different microstructures due to the incorporation of substrate elements, its performance was better than the HVOF coatings, although their Vickers hardness was similar. After heat treating, a significant variation in hardness and wear resistance was observed. For PTA specimens, there were decrease in hardness of 35%, while for HVOF ones this drop was approximately 20%. Nonetheless, the effect of thermal exposure in wear resistance was quite different: an increase of 21% was observed for HVOF coatings, while a reduction of 20% occurred in PTA ones. Microstructures modifications in PTA coatings were significant for their wear resistance. On the other hand, the reduction of porosity and sintering were responsible for a better performance of heat-treated HVOF coatings.

Jul 31, 2018

By Bernhard Hiebl

Global trends that are constantly challenging the iron and steel producers are related to worsening of the iron ore grades, higher substitution rates of main iron ores to cheaper raw materials due to economic pressure and increased environmental standards. Changing the raw materials in an operating plant can significantly influence the sintering or pelletizing process. Adjusting all process parameters to regain stable and high productive operation takes considerable time and causes production losses. Furthermore changes in raw materials lead to variations in the process gas flows and emission concentrations.Therefore SVAI developed two models for numerical simulation of sintering process and pelletizing process. Amongst others the models are based on Ergun equation and include chemical reactions of the related process. For already operating plants the simulations shall predict changes of the process parameters when raw materials are exchanged or when operational parameters are varied. Furthermore the simulations give advantageous information for the design of green field plants and allow the simulation of different plant configurations.The objective of this paper is to demonstrate what the latest developments are in these numerical simulations and what Siemens VAI is doing to overcome the remaining challenges in this field.

Aug 2, 2018

By Bruno Cordeiro Costa

Inseridas em um mercado extremamente competitivo, as empresas siderúrgicas vêm buscando aprimorar seus processos produtivos e de gestão de forma a reduzir custos de produção e garantir sua sustentabilidade. A principal parcela do custo de produção da empresa em relação a um aço inoxidável ligado ao Cromo e Níquel está na Aciaria, e a carga metálica representa mais de 80% deste valor. Visando aumentar a competitividade, foi aberto um projeto para otimizar a carga metálica na Aciaria. A redução da mistura de escórias é uma fase deste projeto. O propósito do presente trabalho é mostrar a metodologia adotada para otimizar o processo de recuperação de sucata das escórias de aços inoxidáveis, minimizando a ocorrência de misturas de escórias, para maximizar seus teores de Ni e Cr e, consequentemente, reduzir o uso de fontes mais nobres e caras destes elementos. Foi adotada a filosofia “Zero de Escória no Chão” e, para alcançar este objetivo, várias ações foram implantadas. Considerando 2011 como base 100%, o teor médio de Ni da sucata recuperada de 3XX aumentou 45% em 2013 e o teor médio de Cr subiu 36% na sucata recuperada neste mesmo período. Como consequência direta da redução da mistura de escórias de grupos de aços diferentes ao longo de todo fluxo produtivo, ocorre a redução dos residuais de Ni e Cr nos aços carbono e elétricos e de Ni nos aços 4XX. A metodologia adotada foi eficiente e os objetivos do projeto foram alcançados.

Jul 30, 2018

By Miguel Araújo Vasconcelos Filho, Ulisses Tetti

In order to determine the influence of the number of increments of the sinter sample on the variability of the chemical composition obtained in Sinter Plant production, a variographic study was carried out. It was performed with two series of samples. The first series was composed of 40 samples with a 6-second interval, with the objective of obtaining the so-called minimum practical error, resulting from the extraction processes of the sample of the conveyor belt and preparation and analysis in the laboratory and the second series composed of 60 samples with a range of 4 minutes, which points to the sample selection error. The results obtained showed that the minimization of the sample selection error occurs for increments spaced in 15 minutes, being in agreement with ISO 3082, but with significantly better results than those currently practiced for intervals between 1hour increments. It was then decided on the suitability of the sampler to allow hourly increments to be collected and on a second opportunity to install a sampling tower with primary and secondary samplers to collect increments every 15 minutes including sample size reduction.

Oct 1, 2019

By Gabriel Burlandy Mota de Melo

Nanopartículas de ferrita de manganês (MnFe2O4) foram dispersas em parafina e as propriedades físicas do compósito resultante foram investigadas por ressonância ferromagnética (RFM). Os resultados mostraram que a dispersão em quantidades moderadas de parafina aumenta significativamente a anisotropia magnética das nanopartículas de ferrita, um resultado que pode ser de interesse para aplicações práticas do compósito.

Oct 30, 2017

By Etiene Pereira de Andrade

Em decorrência de índices de emissão de poluentes cada vez mais restritivos, de programas de incentivo à eficiência energética e do uso de fontes de energia renováveis, a indústria automobilística se renova e desenvolve tecnologias que permitam redução de massa dos veículos conciliada a bom desempenho estrutural e em serviço. Nesse contexto pode-se destacar o processo de Tailor Welded Blank (TWB). Esse processo permite que se reduza o número de reforços empregados no veículo, bem como a necessidade de um maior número de etapas de manufatura. Este estudo trata da caracterização das fraturas observadas em chapas obtidas pelo processo de TWB, para aplicação em portas laterais de veículos, quando submetidas à operação de estampagem profunda. Para a identificação da causa raiz foram realizados os ensaios de tração (de forma qualitativa, buscando apenas definir a região de falha), embutimento e análises metalográficas usando microscópio óptico (MO) microscópio eletrônico de varredura por feixe de elétrons (MEV). Os resultados indicaram que a fratura ocorreu na zona termicamente afetada, e não na zona fundida. Verificou-se, ainda, que a fratura ocorreu por esforços de tração simples, gerados pelo processo de estampagem do componente.

Oct 30, 2017

By Johne Jesus Mol Peixoto, Itavahn Alves da Silva, Marina Braga Campos, Carlos Antônio da Silva

A composição, morfologia e distribuição de tamanho das inclusões presentes nos aços têm forte influência sobre propriedades químicas e físicas como fadiga, usinabilidade e resistência à corrosão. Desta forma, melhorar a qualidade do aço implica em aumentar a limpidez do aço líquido [1]. Para tanto são utilizados processos (que apresentam diferentes custos operacionais) como o burbulhamento de gás inerte na panela e o tratamento no desgaseificador a vácuo RH. O presente trabalho apresenta resultados de simulações matemáticas bem como operacionais dos processos de remoção de inclusões através do borbulhamento de gás inerte e do tratamento a vácuo. É feita uma comparação entre as capacidades de remoção de inclusões destes processos, confirmando a maior efetividade do reator RH.

Oct 1, 2019

By Walter Mazon, Marcello Rodrigues Cruz, Leandro Carvalhar Maciel

Filtration is the operation of liquid solid separation commonly applied in the mining industry. The use of filtering chemical agents is a technical solution viable for filtering optimization. The present work proposed to evaluate two filtering chemical agents (surfactants) to reduce the final moisture content of iron ore concentrate from Ferrous Resources. The leaf test top feed was done with the FLOTICOR FA 7241 and FLOTICOR FA 16557 products. The foaming profile of the filtrate was also evaluated, once excessive foaming is undesired when using this kind of products. The results showed a reduction in the final moisture of the filter cake. The product FLOTICOR FA 16557 achieved the best results, reducing final cake moisture from 10.4% to 9.8% at the dosagem of 25 g/t, besides presenting a fast kinetics in the foam drainage, presenting itself as a technical alternative for filtration optimization.

Oct 3, 2019

By Edo Engel

Blast furnace No. 3 at Zaporizhstal in Zaporozhye is rebuilt in 2016-2017. The Ukrainian company is targeting increased production and availability, mainly through the use of new technology. Zaporizhstal awarded a contract for a new Top Charging Unit to Danieli Corus, after comparing all available technologies. Reliability of the chosen charging device is pivotal, since long outages may be required for maintenance/replacement jobs, which strongly affects the availability of the blast furnace. This article describes the Top Charging Unit including DANCU (Danieli Charging Unit) - a robust hydraulic system. The main focus employed by Danieli and Danieli Corus during the development of this system has been availability and maintainability of equipment. This chute type charging unit has only few major moving parts, none of which is complex or vulnerable. The article also describes the main challenges of the project at Zaporizhstal, such as the use of hot sinter.

Oct 30, 2017

By Abraão Santos Silva

Juntas soldadas são regiões críticas quanto a fraturas. Neste estudo foi analisada a tenacidade à fratura de soldas de reparo de tubos de mastros de sonda de perfuração de petróleo. Foram escolhidos os tubos principais de sustentação dos mastros. Seções do mastro são corriqueiramente reparados por soldagem TIG de raiz e preenchimento por eletrodo revestido. Estes processos provocam modificações metalúrgicas na zona termicamente afetada da solda, o que pode ter reflexo na tenacidade à fratura dos tubos. Foram produzidos corpos de prova para medir a tenacidade à fratura do metal base e da zona afetada termicamente. Os resultados indicaram que não houve redução de tenacidade a fratura devido as alterações microestruturais da zona afetada e isto foi associado ao procedimento de soldagem multipasses utilizado.

Aug 16, 2017