Search Documents

By William P. Stroud

Chemical alteration of the compressive strength of sandstone has been investigated by the U.S. Bureau of Mines (USBM). Successful development of this technology would offer an attractive alternative to the methods now used for stress control in mines. Sandstone cores were stressed to failure under uniaxial compression at two different strain rates. Specimens saturated with either distilled or tap water showed an average 14% reduction in stress at failure compared with those dried in vacuum. Samples saturated with dilute solutions of aluminum chloride, hydrochloric acid, and polyethylene oxide showed no statistically significant difference in failure stress compared with those saturated with water. By contrast, compressive strength of the cores was increased some 7% by saturation with the nonpolar solvent carbon tetrachloride. No correlation was found between zeta potential and compressive strength.

Jan 1, 2010

By Robert C. Merritt

Laboratory amenability studies as well as a pilot heap-leaching investigation of low-grade sandstone uranium ores from Wyoming, New Mexico, and Colorado are described. Sulfuric acid heap leaching with oxidation, for 120 days, extracted up to 98 percent, 90 percent, and 79 percent U308 from Wyoming, New Mexico, and Colorado ores, respectively.

Jan 1, 1976

By Eleanor Abshire

This bibliography is the second in a series that covers the current technical literature relating to the metallurgy of zirconium. The rapid advance in zirconium technology makes it mandatory that abstracts be prepared and compiled as soon as possible to have maximum value; therefore, the information in this volume is not arranged chronologically. As a service to research and production groups, succeeding bibliographies will be issued as new acquisitions accumulate in the Zirconium Information Center sponsored by the Department of the Navy, Bureau of Ships and the Bureau of Mines at the Bureau's Northwest Electrodevelopment Laboratory, Albany, Oreg. The initial volume, Information Circular 7771, Bibliography of Zirconium, covering 969 abstracted reports and 645 United States and foreign patents, was published in April 1957.

Jan 1, 1958

By Mark Springett

The problems inherent in sampling low- grade deposits have long been recognized. As economic grades become lower with increasing metals prices and improvements in recovery technology then the previously difficult sampling problem has consequently become even more demanding. The breakdown of the sample process and error is illustrated by describing in the remainder of the paper some sampling practices that have been utilized on mining and exploration properties and by describing some problems that have been encountered, providing a series of cautionary tales to those involved in any aspect of mine or exploration sampling.

Jan 1, 1983

By C. E. Fivaz

SYNOPSIS Tribute is paid to J.S. MacArthur and the Forrest brothers for their invention. The opinion is expressed that the successful application of their process, not only saved the gold-mining industry on the Witwatersrand from stag¬nation for an indefinite but probably prolonged period, but also made a major contribution to the economic growth of the country in the twentieth century. A background is given of the activities of prominent chemists who researched the solubility of gold in cyanide solution prior to the MacArthur-Forrest invention. An account is given of the invention and patenting of the cyanidation process, and of the golden rule that the patentees laid down for themselves, which came close to wrecking the invention. The South African gold-mining scene from the discovery of gold on the Witwatersrand in 1886 up to 1890 is sketched. An account is given of how, when unoxidized ores were first encountered, the recovery efficiency dropped alarmingly, gold shares were sold on an unprecedented scale, and doom and despondency seized the town of Johannesburg. The complete turnabout in the fortunes of the South African gold-mining industry after the introduction of the cyanidation process in 1890, the steady rate of increase in production after the Anglo-Boer War, and its effect on the South African economy are described. A brief look is taken at the effect of gold mining on secondary industry. The deportment of the gold that is not dissolved from the ore by the cyanidation process is illustrated. Some thoughts are expressed on what can be done to increase the gold recovered by cyanidation.

Jan 1, 1988

By R. J. Colony

MINING geology does not lend itself - very readily to a review embracing "improvements in methods," as perhaps do shop practices or laboratory procedures. The "methods" used in mining geology are simply the application of geology to mining; winning the ore, the handling of material, mechanical appliances, all belong strictly to mining proper, and have no place in a review of geology as applied to mining. A comprehensive review would necessarily cover a .very broad field, which could be subdivided into many -parts. Only a few of these can be discussed here. .Those that have been suggested to the chairman indude :

Jan 1, 1930

New GSP Trade Status Approved.--President Carter, by Executive Order effective March 30, has approved Generalized System of Preference treatment for imports of nonferrous metal products and other imports from Ecuador, Indonesia, Zimbabwe, Uganda, and Venezuela. As of May 2, Afghanistan and Ethiopia will be taken off GSP status. Under the Generalized System of Preferences, certain imports from developing countries are provided duty-free treatment. A country can lose its GSP status if its shipments of the product exceed $41.9 million or more than 50% of total U.S. imports during the preceding year. However, the President can waive the 50% rule in cases where total U.S. imports of an item in 1979 were less than $1 million. Certain nonferrous imports from Mexico, Peru, Chile, and Zambia are already covered by GSP. Hearings April 10 on International Tin Agreement.--The Fifth International Tin Agreement of which the United States is a signatory, which entered into force on July 1, 1976, will expire on June 30, 1981. A negotiating conference for a Sixth International Tin Agreement will be held under auspices of the United Nations at Geneva from April 14 to May 16, 1980.

Jan 1, 1980

Lead Tariff.--The full House Ways and Means Committee approved H.R. 6089 which will have the effect of reducing the tariff on unwrought lead to 3% ad valorem, with a floor duty of 1.0625 cents per pound, compared with the currently effective rate of 3.5% ad valorem. Consideration is also being given to tariff rates on imports of red lead and litharge from Mexico. A consortium of domestic producers has appealed to the Office of the Special Trade Representative (STR) requesting a return to tariff schedules which were in effect prior to the concessions made effective on January 1. Mexican producers have filed a proposal in favor of lower duties, and the matter now awaits a ruling by the STR. Ferrous Scrap Exports.--After holding public hearings and receiving public comments in May, the Department of Commerce announced that it would not institute formal monitoring of ferrous scrap exports, as requested by the Ferrous Scrap Consumers Coalition. The Department said, however, that it would follow the trend of scrap exports and prices. Ferrous scrap prices are currently low and supplies are reported to be adequate.

Jan 1, 1980

By Staff

Minerals contribute to U.S. gross domestic product (GDP) at several levels - from mining and processing to the manufacturing of finished products. In 2010, the estimated real GDP of the United States increased by 2.8 percent compared with 2009 and the estimated nominal GDP was about $14.6 trillion (Table 1).Trends in various sectors of the domestic economy are often rejected in mineral production and consumption rates. For instance, continued declines in the construction industry during 2010 were rejected in further reductions in the production and consumption of cement, construction sand and gravel, crushed stone and gypsum, which are used almost exclusively in construction. Performances in other sectors were mixed and less easily characterized. Recovery from the economic decline of 2008-2009 became apparent in 2010, as prices for many mineral commodities continued to rise with increasing demand for those materials or the products in which they are found.

Jan 1, 2011

By Arno C. Fieldner

This is the fifth of a series of annual reports4/ of technologic investigations conducted by the Bureau of Mines on the occurrence, properties, mining, preparation, and uses of coal. The research of the Bureau is carefully coordinated with the requirements of the producing and consuming industries, with a view to conservation of resources of coal in mining and use, and conservation of the health and lives of workmen employed in these industries. Such coordination is facilitated by the wide range of specialization of the several groups on engaged in studies concerning coal. Here are reported correlated studies ranging from paleobotanic analysis of the formation of coal as it occurred some millions of years ago to the effect of mechanical methods of mining on present-day employment in mines. As this is a summary of the current work of the Bureau of Mines, so the Bureau likewise has provided a condensed review of the outstanding current work of others on research and technology of coal 5/.

Jan 1, 1940

By Tom Treleaven

The success of any blast is dependent on the accuracy of the blast design and the field controls used on the shot. This point cannot be over emphasized because when the geometry is not measured and/or field controls are not properly implemented, it can often have devastating effects on the final blast results. Thus drilling accuracy, tiont row burden control, explosive confinement, energy distribution, explosive selection, timing and structural geology become critical parameters in the design of successful blasts. Understanding the actual dynamics of the blast and why certain results were achieved is the fast step in optimizing a blast design. As stated by R. Frank Chiappetta, “Of all the blast monitoring systems available today, high speed videography still remains as the best stand alone instrumentation system for blast diagnostics.” Over the past years I have analyzed hundreds of blasts using either high-speed lowcams (500 frames per second) cameras or standard digital (30 frames per second). These analyses confirm, without a doubt, that shot geometry, in combination with structural geology, is the most important factor in overall blast results. Drilling accuracy is the single most important component in efficient blasting. Having equal mass associated with an equivalent energy is the basis in which blasts are designed. When drilling inaccuracy or borehole deviation occurs, not only is the energy unevenly distributed, but the basis of all design calculations becomes invalid. Over the past several years, quarry and mining operations have employed the use of boretracking measuring devices to measure borehole deviation and hole toe locations. In cases of operations using top hammer drills, it was discovered that the amount of deviation was significant and far greater than they believed they had. Set up error, improper drilling techniques and bit wear were some of the contributing factors. Through video anaysis of boretracked blasts, blast results were directly linked to drilling ..accuracy. The comparisons here took into account blast design, energy factors and hole sequencing.

Jan 1, 2000

Antitrust Investigation Dropped. - The Department of Justice announced that it was dropping its 5-year investigation of the aluminum industry. The investigation was over whether the aluminum companies were acting as if they were a shared monopoly. Deep Seabed Mining. - The Department of Commerce's National Oceanic and Atmospheric Administration (NOAA) has established an Office of Ocean Minerals and Energy which will be responsible for implementing the Deep Seabed Nard Minerals and Energy Act and the Ocean Thermal Energy Conversion Act. It will establish licensing and regulatory programs.

Jan 1, 1980

By GEO M. FOWLER

AN appraisal of the activities of the mining geologists during 1936 clearly indicates the ever in- creasing utilization of geology in the search for ore. Few men with geo- logic training are idle at present; this is particularly true regarding recent graduates. Many have accepted employment in distant fields, such as the Philippines and South America, and greatly increased mineral production from these places reflects their activities. In North America, regions of intense mineralization formerly important are being restudied in greater de- tail and with better understanding; as a result, new mineral wealth is being found in many such districts. Much is being done by private companies and individuals, and it is to be hoped that mining companies will increasingly make available the purely scientific results of such studies by permitting their geologists to publish. On such generosity to a large extent will future advances in ore finding depend.

Jan 1, 1937

By W. W. Adams

The accident-prevention record of the coal-mining industry in the United States was more favorable in 1936 than in 1935, both from the standpoint of the relative safety of the individual miner on the job and of the price in life and limb that the Nation paid for its year's supply of coal. The increase in relative safety of the individual miner was indicated by a lower death rate and a lower injury rate than in the preceding year per million man-hours of exposure to the hazards of mining; that is, per million hours of work performed by the employees. (See table 1.) A reduction in the price in life and limb that the Nation paid for a year's supply of coal was indicated by a smaller death rate and a smaller injury rate per million tons of coal produced. Thus the individual miner was a better insurance risk, as far as accidents were concerned, in 1936 than in 1935, and a ton of coal used in the homes and industries of the country represented less human suffering than in 1935. The two points of view are distinct, and both should be kept in mind when considering accidents and safety in coal mining or in other industries. More men were employed in 1936 than in 1935, and more workdays were available for the individual miner. Large gains were also made in the total number of man-shifts and man-hours worked in the industry as a whole. In number of tons of coal mined, 1936 showed large gains over 1935. Moreover, the average output of coal per man-hour worked was higher in 1936 than in 1935. All of these gains were made without lengthening the average number of hours of work per man per day.

Jan 1, 1939

By R. J. Goodman, P. Lafleur

This paper presents a current interpretation and projections of recent statistics on raw materials availability based on familiarity with the Canadian steel industry and its development. Problems and opportunities are recognized and discussed.

Jan 1, 1976

By G. W. Poling

This paper evaluates current environmental protection legislation, guidelines and criteria, focusing mainly on the land and water disposal of mill tailings. Effluent criteria and regulatory mechanisms are proposed, and submarine tailing disposal is discussed at length. The importance of basing regulations on the best available rationale is stressed.

Jan 1, 1979

By A. B. Hooker, E. J. Coggeshall

"Dry cells are modified wet primary cells in which the electrolyte is held by absorbent material so that it does not spill aid the cell jars are sealed to prevent evaporation of the absorbed electrolyte. Most dry cells in commercial use are modifications of the Leclanche wet cell. In their usual form they have a hollow cylindrical zinc negative pole that constitutes the containing vessel. An absorbent material, either as a lining in the zinc jar or a bag, separates the zinc cylinder and a rod or flat plate of carbon placed axially inside. A mixture of crushed coke, graphite, and manganese dioxide is tamped about the carbon rod, and the whole mass is saturated with salaanoniac-zinc chloride solution.Dry cells are suitable for services that require minute currents continuously or larger, though limited, amounts of current intermittently. Though limited in this way, they have a wide use, even in underground mining. This paper details some of the applications of dry cells in mines, particularly from the standpoint of greater safety through their use.APPLICATIONSThere are four fields of application of dry cells to mining: (1) Electric shot firing; (2) auxiliary lighting; (3) signaling; and (4) testing.SHOT FIRINGFiring an electric detonator requires very little electrical energy because although the current flow may be 1 to 3 amperes the duration of flow is so small (1 to 4 milliseconds) that the energy withdrawal per shot is almost negligible. Batteries for shot firing need not be large; they may be used for firing either single or multiple shots."

May 1, 1934

By David K. Hylbert

This study investigated stratigraphic and structural causes of roof falls in room-and-pillar drift coal mines in nine mines in eastern Kentucky. A contract modification provided for remote sensing studies in the Dunkard Basin of West Virginia and Pennsylvania. Results of stratigraphic and structural studies of an earlier contract (H0133018) were applied to several new mines. It was found that similar rock sequences contributed to unstable roof conditions. Structure contour and isopach maps were found useful In projecting these trends together with fence diagrams. Using Landsat imagery, a direct relationship was found between lineament direction and the trends of rock jointing, roof fall zones, "snap top" zones and sandstone channels in the examples cited. It was found that, by analyzing lineament intersections, from 50 percent to 65 percent coincided with roof falls.

Jan 1, 1980

By S Worden, P A. Kirsch, A Kirsch

Despite the current downturn, coal remains an important commodity in the Australian economy. Increasing coal resource development has resulted in increasing competition for land use in coal mining regions across the country with communities and other stakeholders becoming more adept at articulating their concerns regarding this competition in a range of traditional and social forms of media. In this environment, obtaining and maintaining a social licence to operate (SLO) is problematic and has been identified as the fourth greatest risk facing the international mining industry.This research presents the findings from a longitudinal study on how Australian newspapers frame the views of coal mining stakeholders across each stage of the coal mining life cycle. News stories from national, state and regional newspapers in 2000, 2006 and 2013 were analysed.Over the study period, there have been significant changes in the coal mining themes being covered by Australian newspapers, the number of stories being published, the number of newspapers covering coal mining stories, and the diversity of stakeholders being quoted. How do the dominant themes in media communication change over time? How do these changes impact mining across the life-of-mine?The research confirmed that Australian journalists use framing, priming, labels and bias to conceptualise and understand the events that they report, and that this behaviour has a profound effect on public opinion.CITATION:Worden, S, Kirsch, A and Kirsch, P A, ?2014. Moving beyond economic framing of the Australian coal industry, in Proceedings Life-of-Mine 2014 , pp 365–376 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By John Wilson

This report describes the performance of Phase I of a project to design, analyze, and demonstrate a multilift longwall mining method applicable to mining coal seams twelve (12) feet or more in thickness. A non-simultaneous multilift operation is the most viable thick seam mining technique for introduction to the United States coal industry. In the case of the proposed site at Emery, Utah it will result in an increase in coal extraction from 30% with present methods to at least 50% and possibly more. The major technological advance involved in this project is mining a lower lift under a previously mined upper lift. To accomplish this, entries must be developed and maintained beneath the upper lift gob. This will necessitate the use of steel supports at frequent intervals throughout the lower lift' entry system. This has not been done in the U.S. to date. An economic analysis of the project indicates that, while this method will result in a higher than average cost per ton for coal mined, the coal would be competitive with current-operation in the area.

Jan 1, 1976