Search Documents

By Jim Steding

L.G. Barcus and Sons, Inc. recently completed a three-phase project for the expansion of Presbyterian Hospital in Albuquerque, New Mexico for McCarthy Construction Co., the Construction Manager for the project. It was a challenge that allowed Barcus to demonstrate many of it's strengths. Safety of people and property, restricted access, low headroom conditions, extensive planning to maintain hospital operations and a tight schedule were all key elements affecting the successful installation of the Augered Cast-In-Place Piles. Phase I began with installing and performing a 450-ton pile load test on an 18-inch diameter Augerpile 65 ft long. The load test was installed and performed directly in front of the Emergency Room entrance. Space was limited and the E.R. had to remain open with uninterrupted ambulance access. The results of the load test were outstanding. In fact the test pile performed so well that some of the job piles were shortened from 75 ft long to 65 ft long. [ ]

Jan 1, 2003

A hard lump char containing only 4 to 5 per cent ash, 0·25-0·30 per cent sulphur and a trace of phosphorus has been produced from Latrobe Valley brown coal by slow drying and carbonization of ordinary industrial briquettes at temperatures between 7000 C and 14000 C. The briquette char can be made with a variety of reactivities by varying the maximum temperature of carbonization; the higher the temperature, the lower the reactivity. The strength of the fuel compares favourably with metallurgical coke made from black coal, though it may not be quite so resistant to abrasion. Experiments in a small experimental cupola indicate that it will make a satisfactory fuel for use in iron foundries. It may also find extensive application as a smokeless fuel in other branches of industry and in household heating appliances.INTRODUCTIONVictoria, like South Australia and Western Australia, is apparently without 'significant deposits of black coal of coking quality but there are huge reserves of brown coal of high moisture content (60-66 per cent) in the Latrobe Valley (well over 20,000 million tons have been proved) and there are other important deposits in the south central portion of the State (Herman, 1952).For three decades Victorian industries, including a few metallurgical firms, have been using the briquettes made at the Yallourn factory of the State Electricity Commission of Victoria (S.E.C.). These briquettes, having a moisture content of about 15 per cent and a calorific value of approximately 9,500 B.T.U. per pound, are satisfactory for certain grate-type furnaces but they are not suitable for use in cupolas of other shaft furnaces because they disintegrate badly on rapid heating.

Jan 1, 1956

By Ross R

Although mining is an old industry its management is quite a new science, and its complications are now being recognised as demanding expert knowledge in many branches of technical and professional education. Not the least amongst these isaccountancy, for probably its most important problem is "How to control the expenditure." Unlike most businesses a mining company stands almost entirely in the light of a purchaser in the world's markets, and not as a seller, except say for product so the established and perfected systems of modern industries cannot be adopted for mining purposes. For this reason it has been left for late years to consider the matter seriously, and now a number of well-managed concerns have devised costs systems to suit their own requirements.Very little, however, has been published and even that is disjoined and difficult to make use of. Some of the costs systems in vogue, although elaborate and imposing, are not of very great value for keeping check on wasteful expenditure, or for displaying the commercial effect brought about 'by any particular change in practice, or by an addition or alteration to a portion of existing plant.

Jan 1, 1912

By Pierre Mousset-Jones

A questionnaire was sent out to three classes of mines to determine the extent of the heat problem in U.S. and Foreign underground mines. The following list shows the replies received from this questionnaire, however not all the known hot mines in the US replied. A complete listing of the results can be seen in Appendix I. 1) US coal mines - 37 replies 2) US non coal mines - 23 replies 3) Foreign non coal mines - 36 replies. At the present time there are approximately eleven non coal and one coal mine in the US experiencing heat problems which require special efforts to maintain an acceptable working place climate. However since the survey was completed some of them have been placed on standby. The Mine Safety & Health Administration (MSHA) does not have any specific regulations relating to heat stress. Informally the American Conference of Governmental Industrial Hygienists guidelines are followed which use wet bulb globe temperature (WBGT) with values ranging from 26.7°C to 31.1°C for a moderate workload, and different rest regimes. An MSHA report (Misaqi 1976) recommended that conditions should not exceed 26.1°C WBGT for men and 24.4°C WBGT for women. However, quite recently the organizations involved with planning two of the proposed nuclear waste repositories in the United States, have opted for the criteria of an air cooling power of 300 w/m2, and a WBGT of 27'C respectively.

Jan 1, 1986

By Cz. Mora, A. Pawelczyk, D. Hreniak, P. Nowak, A. Dyonizy, S. Strek, W. Strek, K. Grabas, A. Ostrowski

Globalization and a growing demand for limited raw material resources have forced changes in the approach to the supply chain. This is particularly true in the case of rare earths, which are regarded as one of the most important development indicators of modern technologies. To ensure a secure supply of commodities, the European economies have been prompted to investigate REE recovery from sources which until recently, for technical or economic reasons, were considered not sufficiently attractive. An interesting example is apatite phosphogypsum waste dumps. The REE content in these waste dumps averages around 0.5-1 %. One of the most important phosphogypsum locations in Poland is the Lower Silesia region where a phosphoric acid Chemical Plant "Wizów" operated for several dozen years. In this work, rare earths are leached from the phosphogypsum crystalline structure by a chemical treatment and can then be separated into individual chemical compounds. The technology used in these recovery tests, matches up to a coherent European raw materials policy supporting effective management of resources and promoting waste materials recycling.

Jan 1, 2014

By W. William Culver

James Douglas became known in the nineteenth century for two reasons fundamental to his mining career: (1) his experimental work with copper hydrometallurgy, and (2) his grasp of the idea that the quantity of copper ore matters more than the quality. On the first reason, there is a moment for any technology that’s critically important—when it moves from an area of scientific interest to one that companies are founded on. This paper examines the original 1869 Hunt and Douglas Copper Process in the context of science and engineering as they were in the 1860 and 1870s. It was a “humid” process, developed at Quebec’s Harvey Hill Mine. Chemically, the Hunt and Douglas vat leaching process succeeded, but not the original companies using it. On Douglas’ understanding of ore quality versus quantity, luck had it that the first company to field test the Hunt and Douglas Copper Process was in Chile. The Hunt and Douglas patent made that transition from experimental model to operational plant in 1870 when the Compañia de Minas de la Invernada was organized in Valparaíso. As a joint-stock company, Invernada spread the risk of investing in the revolutionary, but untested, Hunt and Douglas Process. The company brought Douglas to Chile as a consultant in 1871. His experience with hydrometallurgy, combined with what he learned about the copper business while in Chile, set him off on a career in metal mining that both surprised Douglas and made him wealthy.

De acuerdo a los últimos trabajos realizados sobre la exploración en la mina Cercapuquio, se realizó un muestreo de la veta 53 donde se observó que en la caliza, más allá del ala norte, como en el lugar llamado Chaupirange, existe grandes depósitos de carbonado estático con siderita y limonita, en bolsa de erosión de la caliza normal. Asimismo, se describe otros métodos utilizados para la exploración geofísicadel subsuelo como los electromagnéticos e inducción. En ese sentido, se trata de crear un campo (primario) a través de una corriente eléctrica alterna (primaría) en un circuito. A este campo, es concadenada una corriente (secundaria) que circula en el cuerpo conductor mismo ( en general desfasada respecto de la primaria), que genera a su vez, un campo secundario. Este último se compone con el campo primario para formar un campo total, que está relacionado con la posición y naturaleza del cuerpo conductor que funciona de circuito secundario.

Jan 1, 1956

By Henrique Hipolito, Caio Alves

Waelz process is a method applied in the zinc oxide production and is one of the largest sources of carbon emissions within the zinc industry. The solid carbon used for heating and for reduction reactions is provided mainly by the coke fed with the EAFD in the Waelz kiln. Both chemical composition and physical properties of the coke are important to transportation and to the process. Decarbonizing the Waelz process by replacing the traditional fuel source using alternative biogenic fuel, for example, offers a potential solution to reduce the carbon footprint, which is aligned with the ESG perspective.

Sep 29, 2023

By Armstrong M

The Coal Mining Engineering Branch of the New South Wales (NSW) Department of Mineral Resources, in its continuing effort to improve coal recovery from underground coal mining operations, has undertaken a study of the mechanics of sub-surface deformation caused by caving of the extracted area behind retreating longwall faces. The strata movement was monitored by a multi-wire borehole instrumentation system consisting of mechanical anchors installed at different horizons in a borehole extending from the surface to the coal seam. The mechanical anchors were connected to the suspended weights on the surface by stainless steel multi-strand wires. The movement of these weights was monitored as the longwall face approached and retreated past the borehole. The anchors started subsiding as soon as the face retreated past the borehole and continued to subside until the subsidence levelled off when the face retreated 900 m past the borehole. The zone of major caving and bed separation extended to roughly 10 to 13 times the extracted seam thickness and high tensile strains developed inthis zone. The bulking factor of broken strata was less than 1.14 which indicated that the roof layers collapsed in big blocks. The goaf compaction was almost complete when the face retreat was 200 m. Low tensile strains prevailed in the strata overlying the zone of caving and bed separation.

Jan 1, 1986

By Dave Marsh, John Goode, Niels Verbaan, Kevin Bradley, Henrie Notzl

The mineralogy of the Avalon Nechalacho deposit is complex with significant fractions of HREEs, Zr, and Nb found in refractory minerals such as zircon and fergusonite. Sulphuric acid baking followed by water leaching can be used to extract REEs from flotation concentrates, but acid baking does not completely "crack" the zircon and fergusonite, so the extractions of Zr, Nb, and HREEs are not high. An alternative flowsheet has been developed that is able to obtain significantly improved extractions of HREEs, Zr, and Nb from flotation concentrates or acid bake residues. This is accomplished by cracking the zircon and fergusonite minerals with caustic soda at high temperatures, followed by water washing to recover excess caustic soda and soluble sodium silicates and phosphates. REEs, Zr, and Nb in the solid residue can then be solubilized with HCl or H2SO4. This paper highlights some of the findings from an extensive laboratory program and discusses several flowsheet implications.

Jan 1, 2014

By Staff

One hundred thousand miles of flying over the North country without a single air casualty; much of it over virgin territory probably never before visited by white men; some of it over regions that abound with possibilities for minerals; all of it effective, for exploration and the establishment of bases and supply-stations, and for the carrying of men and their tools and provisions- this, briefly, is the record of Northern Aerial Minerals Exploration, Limited, a Canadian company organized Jess than nine months ago, which has been functioning, without interruption, during spring, summer, and now into winter. Our planes have ranged from the Alaskan boundary on the west to the Labrador coast on the east, and from the Transcontinental railway north to the Arctic circle. Our prospectors, carried on trips of hundreds, and occasionally thousands, of miles, have gone over large sections of country which were never before explored, and at the end of the prospecting season the Company finds itself in possession of several groups of important gold claims, which look most promising. In addition to this, we have been in contact with deposits of almost every known mineral.

Jan 1, 1929

By Rick Wilkins

The stability of steep embankments is a major safety issue in open pit mining, highway passes, and earth filled dams. A failure in any one of these situations could mean a loss of very expensive equipment, a long term inconvenience, and more importantly, a loss of life. These possible catastrophes could be avoided by installing a reliable real time monitoring system. Robotic total stations (RTSs) give one possible cost effective solution to creating a near real time monitoring system. Repeated surveys at predetermined time intervals can automatically generate warnings if slope movements exceed a preset tolerance level. The variation in atmospheric refraction, combined with possible instabilities in reference targets, can make a monitoring system based on RTSs produce false alarms. A methodology has been developed at the Canadian Centre for Geodetic Engineering (CCGE) for reducing these systematic error effects. The methodology has been realized in the creation of a software package that has been successfully implemented at large earthen dams in California and at an open pit mine operation in British Columbia.

May 1, 2002

By W. G. Freeman

It is unlikely, as In the past, improvement in truck efficiency and capacity can fully offset the effects of inflation, fuel costs/shortages and ever increasing haul distances. There-fore, investigations of haulage systems less sensitive to these problems are warranted. Thus, this U.S.B.M. contract research study on alternative continuous haulage systems was prepared. This study identifies the physical, economic and technological parameters in the application of continuous haulage systems with special attention to under pit slope conveyors and skip hoisting systems. The evaluation data was gathered from extensive literature searches. European/North American mine visits, and industry comments. The study concludes that continuous underground haulage is a viable method within the proper geometric configuration.

Jan 1, 1978

By P. A. Witt

"Highland Valley Copper is a conventional truck-shovel mining and flotation concentrator operation located 75 km southwest of Kamloops, British Columbia (Fig. 1).The ore is situated within a porphyry copper deposit and is mined at a rate of 135,000 mt/day from two separate open pits. The nearby mill produces concentrates containing 375 million pounds of copper and 5 million pounds of molybdenum metal yearly. In the Valley pit, head grades are roughly 0.40% Cu at a 0.23% Cu equivalent cut-off. The Valley pit strip ratio currently sits at 0.55:1 with waste quantities made up of separate rock and unconsolidated overburden units. From the mill, concentrates are trucked to nearby Ashcroft and then hauled by rail to ocean port facilities in Vancouver. The mine employs 950 people and is planned to operate until 2009. The operation is a partnership between Teck Cominco (63.9%), BHP Billiton (33.6%), and others (2.5%). Management is shared by the two principal owners and directed by a management committee."

Jan 1, 2005

By Mauro Andrés Cerra Flórez

O presente estudo visa avaliar a resistência à corrosão de dois aços alto manganês com relação ao aço 9% Níquel em solução eletrólito 0,001M de H2SO4. Para esta pesquisa foram utilizados dois aços com teores de manganês de 22% e 26%, e a liga de aço 9% Níquel que é amplamente utilizada na indústria petroquímica. Os ensaios realizados para comparação da resistência à corrosão foram o monitoramento do potencial de circuito aberto (OCP) e polarização linear anódica. Foi escolhida a solução de H2SO4 pela presença do enxofre, oriundo dos campos de produção como impureza no gás natural. Foram utilizadas as técnicas de Microscopia Eletrônica de Varredura (MEV) e Espectroscopia de Energia Dispersiva de Raios-X (EDS) para a caracterização dos produtos de corrosão. Os resultados obtidos mostraram que os aços alto Manganês apresentaram valores similares de resistência à corrosão, mas ainda inferiores em relação ao aço 9% Níquel.

Oct 30, 2017

By L. van Hijfte, A. Piché

"Drilling and blasting are fundamental operations in the mining cycle and constitute an important component of the mining costs. Problems associated with improper drilling and blasting practices can create losses of several millions of dollars per year. For this reason, a Blasting Technology program was initiated in 1984 at the Noranda Technology Centre (NTC). In this paper, advances made at NTC in drill and blast technology are reviewed. Impacts of drilling and basting for Noranda are assessed in terms of dilution and ore losses. Future challenges are addressed. IntroductionUp to 1997, Noranda was a diversified natural resources company that operated in three sectors: mining and metallurgy, forest products, and oil and gas. The company employs more than 33 000 people in operations and sales offices around the world. Today, Noranda has returned to its roots in mining and metallurgy. The new vision of Noranda is to be dedicated to the responsible and profitable development of mineral resources around the world for the benefit of its shareholders. In so doing, Noranda will continue to be deeply committed to the environment, health, workplace safety, cost competitiveness and return on capital. Technology is an integral part of Noranda’s success strategies. For this reason, the Noranda Technology Centre, formerly known as Noranda Research Centre, was founded in 1963. Since then, it has undergone four expansion phases to keep up with the increasing needs of the businesses. Today, NTC employs more than 220 specialists who work in partnership with different Noranda companies to identify, develop, and transfer technology to the operations, as well as to explore new sectors of activity."

Jan 1, 2000

By G. Boehler

The purpose of this program is to demonstrate the feasibility and practicality of noise control for secondary and tertiary crushers in surface non-coal mining plants and mills. It is a part of the broad Bureau of Mines program to reduce noise in mines to levels mandated in the Coal Mine Health and Safety Act. Utilizing the results of previous contractual research efforts in which noise levels of secondary crushers had been measured, two noise enclosures were designed and evaluated for the REXNORD Symons 7-ft diameter secondary and tertiary crushers installed at the Jackson County Iron Company, in Black River Falls, Wisconsin. The first enclosure had a circular shape following closely that of the crusher and was built up entirely of quick-release panels which can be handled by the crusher operator alone. The second enclosure was octogonal in shape and can be rapidly removed, partially or totally using an overhead crane. Both enclosures fully satisfy the noise reduction objectives and permit daily and long-term maintenance of the crushers. Cost analyses show the cost of the enclosure to be less than 10 per cent of the cost of the crusher, the cost of the octagonal enclosure being estimated at only 60 percent of that of the circular one, e. g. $15,000 against $25,000. It is concluded that the octagonal enclosure best meets the needs of the Jackson County Mining Company and it is recommended that an experimental enclosure be built at the earliest possible time, as proof-of-concept.

Jan 1, 1977

By Douglas Brittsan

This paper presents pile tension and compression load test results for the Southern Freeway Viaduct (North) pile load test site. The testing program represents a collaboration between California Department of Transportation (Caltrans), Federal Highways Administration (FHWA), and a group of pile manufacturers and construction firms. The participating manufacturers included Fundex, Halliburton, Monotube, and Nicholson, with each firm supplying proprietary pile systems. The field test program measured and will allow the direct comparison of the tensile and compressive capacity of nine common and proprietary pile systems installed in nearly identical soil conditions. Data reported here-in details pile compression and tensile load-deformation measured at the pile head. Cursory data regarding pile installation details are included to aid in data interpretation.

Jan 1, 1993

By Phillip J. Mackey, Gerardo R. F. Alvear F.

It is now 38 years since the publication of the first edition of "Extractive Metallurgy of Copper" by Professor W.G. Davenport and the late Professor A.K. Biswas. The text book would be issued in a total of five editions, soon became the standard for students and those in industry. Interestingly it was published at the onset of great change in the industry. This was a time when sulphur dioxide controls in the USA were introduced, and almost simultaneously, world oil shocks caused significant increases in the cost of fuel - all leading to efforts to adopt new technology and move away from the reverberatory furnace, which had no potential for sulfur capture and required large amounts of fuel. At the time of publication of the book, new processes such as the Noranda Process and the Mitsubishi Process were in their infancy, while flash smelting (which was first commercialized in 1949 at Harjavalta, Finland) had made significant in-roads in boosting copper output, with some 22 new flash smelters licensed by 1976. Computer technology and associated process control techniques were rudimentary compared to systems today, available physico-chemical data remained largely in tabulated format and needed to be manually entered into the main frame computers of the era, while modeling techniques common today had not yet been developed. The copper industry has therefore seen immense changes since the time of this textbook: world tonnage of smelted copper has risen from 7.34 million tonnes/year in 1976 to 16.7 million tonnes/year in 2012, over a two times increase. Technologies such as the El Teniente Process, or Top Submerged Lance technologies, typified by the ISASMELTTM, not commercialized at the time, now treat large tonnages of copper concentrate in a single furnace. Advanced heat and mass balance software and thermochemical modeling are now used extensively to examine chemical and physical characteristics for process design and to support process optimization. These changes in the industry have been chronicled in subsequent editions of the book. This paper looks at the issues and problems seen in 1976 and over the intervening years, and compares this with the challenges facing the industry with the available tools and technologies today. Some ideas looking into the future are also discussed in the paper.

Jan 1, 2014

By JOHN G. RAYNER

An examination was made of the filtration characteristics of a haematite slurry using a range of polyacrylamide based flocculants in solutions containing up to 3 per cent sodium chloride. The polymers used were "high" and "Iow" molecular weight and had from 0 to 40 per cent charged groups.Increasing charge density tends to reduce the dose required to achieve optimum performance measured by filtration rate and by cake moisture. In general increased salt addition tends to increase the dosage required to achieve these optima. Both these observations result from the change in polymer extension and accord well with the bridging theory of flocculation.The dose required for optimal cake moisture is up to three times greater than that required for optimal filtration rate. This effect is reasonably consistent for all polymers studied and appears to be non-linearly dependent on salt concentration, with the difference being small at 0 and 3 per cent but quite significant at 1 per cent.

Jan 1, 1987