Search Documents

By Raymond W. Henn, Kent A. Pease, Glen J. Rorison

The paper focuses on construction of a 2.55-km (8,365-ft) long, 2.4-m (8-ft)diameter storm drain tunnel in Evansville, Indiana. The tunnel was driven through saturated soft ground varying from clay to fine sand. The paper presents: an overview of design and design rational including specific EPB machine requirements; the contractor’s proposed and accepted alternative construction methods and TBM design; and construction issues and performance. Some of the key points discussed are the use of the TBM in different operational modes for alternative ground conditions, the effectiveness of dewatering systems, production rates, and issues such as surface settlements and gas.

Jan 1, 2001

By D. N. Adams, M. M. Wong, M. J. Robison

Islais Creek Contract E, a transport/storage tunnel in San Francisco, was visited on a fieldtrip during construction by delegates to the 1995 RETC. This paper is a follow-up to that fieldtrip. The project’s two tunnels are 3.7 m and 3.2 m finished diameter, 155 m and 77 m long, respectively. The contractor used 1,000 overlapping jet grout columns to pre-treat the weak Bay Mud along the tunnel alignments, then mined them with an open faced tunnel shield, eliminating the need for compressed air tunneling. This paper documents the jet grouting program and the tunneling operation used on the project.

Jan 1, 1997

By Raj K. Rajamani, Sanjeeva Latchireddi, Dave Plummer, Stieger. Julius

"The Cortez SAG mill liner design was recently modified to improve the mill operating energy efficiency. In addition to the expected benefits, the design change unexpectedly played a significant role of verifying the proposed grinding circuit expansion for the Cortez Hills project as well as illustrating current SAG mill bottlenecks. This paper will discuss the evaluation that addressed operator and maintenance observations, historical PLC data, and “crash stop” observations to calculate charge motion, packing between lifters, and slurry transport through grate and pulp lifters. The performance of the new shell and discharge end liner design will also be discussed as well as their role in the possible grinding circuit expansion.INTRODUCTIONCortez Gold Mines commenced operation in 1969 with its Mill #1 rated at a nominal 2,000 tons per day. Mill #1 was a conventional rod mill/ball mill circuit followed by an 8-stage CIP circuit. In the early 1990s the Pipeline deposit was discovered and subsequently Mill #2 was built to process the increased ore volume. Mill #2, commissioned by mid-1997, was a nominal 10,000 tons per day SABC circuit followed by an 8-stage CIL circuit for oxide gold ore. Operating and commissioning details of this plant have been published elsewhere (Powell, 1998). By late 1998, there was not enough ore volume to support both mills so the smaller, higher operating cost Mill #1 was put under its current care-and-maintenance status. A simplified flowsheet of the current mill is shown in Figure 1."

Jan 1, 2007

By William D. Dodge

A typical quality program plan is presented for explosion-proof (XP) electrical enclosures. The plan is suggested for manufactures of XP enclosures which are to be certified by MSHA for mining use. The plan describes the quality system, organization and implementing mechanisms which are to be applied in the manufacture and delivery of certified XP enclosures. Example forms and example procedures are included.

Jan 1, 1984

By Frank E. Williams

This Bureau of Mines report describes 147 known fluorspar deposits in New Mexico and briefly mentions 54 miscellaneous occurrences for which little or no information was obtained. Most miscellaneous occurrences are minor and too poorly exposed to be considered more than prospects. History and production of fluorspar in New Mexico, type of deposition, mineralogy, uses, and grade specifications are discussed. Total mine production of fluorspar in New Mexico is nearly 641,000 tons of various grades of crude ore and hand-sorted material. Fluorspar deposits occur in 13 of the State's 32 counties. Grant, Valencia, and Luna Counties account for 86.4 percent of the total production. During the investigation, 141 deposits were visited. A total of 72 character samples was collected for assay, and 3 larger samples were collected for bench-scale metallurgical tests. Results of these metallurgical tests indicate that an acid-grade product can be obtained with 95 percent recovery of the CaF2 content of the crude ore.

Jan 1, 1966

By E. L. Bruce

Introduction The Outokumpu copper mine is situated in eastern Finland, 50 kilometers west of the city of Joensuu or 225 kilometers directly north of the city of Viborg (Viipuri), which is situated at the eastern end of the gulf of Finland (Figure 1). The ore-body was discovered in 1910 by Dr. Otto Trüstedt after two years of careful, scientifically-directed, search. During the early period of development of the mine, the ore was treated locally and the copper re-covered by an electrolytic process. Now the ore is concentrated by tables and by flotation. The concentrates are shipped to Germany for refining. In 1929 the mine produced 150,000 tons of ore from which between 20,000 and 25,000 tons of flotation concentrates containing 20 per cent copper were produced. Profits in 1929 were approximately half a million dollars, but the present price of copper will affect very seriously the profits for 1930. The ore reserves are given as between 7 and 8 million tons (1). The grade of ore is stated to be 4 percent to 6 percent copper, with a little zinc.

Jan 1, 1931

By Gregg Hodges, Fred Schoenbrunn, Steve Slottee, Chad McCleary

"In December, 1999 Stillwater Mining Company (SMC) commissioned a new paste /cement backfill plant to supplement the existing sand backfill system for the cut and fill mining operation at it’s Nye, Montana mine. The new plant uses the Baker Process Deep Cone TM Paste Thickener to thicken the total concentrator tailings from 30% solids slurry to a 71% solids paste. This paper describes both general paste formation concepts and the evolution of the SMC paste plant operation from original design criteria, through problem solving and plant modifications, to the operation of the existing plant.Although the original process design was not effective for consistently producing and delivering acceptable paste to the stopes for backfill, SMC was able to make the mechanical and process modifications which allow the plant to now produce and deliver an acceptable product to the stopes. Ongoing test work is targeted at increasing the pumping range of the system, increasing the paste solids concentration from the Deep Cone Paste Thickener and reducing the operating and maintenance costs of the system.INTRODUCTIONThe authors would like to thank both Stillwater Mining Company (SMC) and Baker Process for their assistance in the preparation of this paper. Stillwater Mining Company chose not to participate directly in this paper due to time constraints, but was very helpful in answering questions concerning their approach to problem solving and specific details with regard to engineering criteria.This paper will begin with a general review of the technical and mechanical concepts in paste formation and then focus on the overall design, start-up and problem solving process for the paste backfill operation at SMC’s mine and concentrator near Nye, Montana."

Jan 1, 2001

By Frank E. Williams

This Bureau of Mines report describes 147 known fluorspar deposits in New Mexico and briefly mentions 54 miscellaneous occurrences for which little or no information was obtained. Most miscellaneous occurrences are minor and too poorly exposed to be considered more than prospects. History and production of fluorspar in New Mexico, type of deposition, mineralogy, uses, and grade specifications are discussed. Total mine production of fluorspar in New Mexico is nearly 641,000 tons of various grades of crude ore and hand-sorted material. Fluorspar deposits occur in 13 of the state's 32 counties. Grant, Valencia, and Luna Counties account for 86.4 percent of the total production. During the investigation, 141 deposits were visited. A total of 72 character samples was collected for assay, and 3 larger samples were collected for bench-scale metallurgical tests. Results of these metallurgical tests indicate that an acid-grade product can be obtained with 95 percent recovery of the CaF2 content of the crude ore.

Jan 1, 1966

By John J. Mulligan

Coalbeds were discovered in outcroppings of the Beacon group of sediments on the north end of the Willett Range ( altitude 77 ° 11 ' S , longitude 160 ° 20 ' E ) , Victoria Land , Antarctica , in December 1960 during an investigation undertaken as part of the U.S. Antarctic Research Program under the auspices of the National Science Foundation . Three separate exposures of coal or coaly material were found . Two of the exposures contain , respectively , eight and four beds of hard , compact , finely banded attrital coal ranging in thickness from 8 feet downward to a few inches , and reported to range in rank from mediumvolatile bituminous to semianthracite . The coals are associated with carbonaceous shales containing an abundant assemblage of fossil plants resembling those associated with the Permian coals of Australia and other Gondwana areas . The third exposure , apparently somewhat higher in the stratigraphic sequence , contains only coaly plant fragments scattered through a thin conglomerate and overlying sandstones . A sandstone bed that overlies these coal - bearing sandstones contains abundant logs and fragments of silicified wood . Preservation of features is poor , but one segment of a silicified stem suggests comparison with Rhexoxylon , a gymnospermous tree that usually is considered indicative of Triassic age . The Beacon sediments in this area have been invaded , broken , and uplifted by a massive series of diabase sills and dikes greater in volume than the intruded sediments . The heat emitted by these intrusives must have advanced the metamorphic development of the coals . However , there is no evidence of alteration to graphite , and coal found in direct contact with a diabase sill contains no vesicles or other usual evidences of natural coking . Either the pressure of overlying rocks inhibited the development of coke , or the coals had been metamorphosed beyond the coke forming stage before the igneous intrusion .

Jan 1, 1963

By P. L. Russell, M. E. Volin, F. L. C. Price, D. H. Mullen

Tin deposits in Catron County, New Mexico, were explored by the Bureau of Mines under authority of the Strategic Minerals Act of August 1939. The investigation covered both lode and placer deposits and was later extended to deposits in Sierra County. Six of the known deposits were examined by E. D. Gardner, supervising engineer of the Southwest Experiment Station of the Bureau of Mines, and S. G. Lasky, a geologist of the Federal Geological Survey, in June and July 1939. It was recommended that the more promising occurrences be explored by test pitting, trenching, and sampling. Field work, under supervision of M. E. Volin, began in September and continued through December 1939. The area was mapped by Carl Fries, Jr., of the Federal Geological Survey, in 1939 and 1940. The La Cruz Development Co. acquired control of the Squaw Creek placer claims in 1942 and began active sampling and development preliminary to large-scale operations. The result of this work showed a considerably higher tin content than that found by the Bureau of Mines in 1939. Because of this report and reports from other parts of the district that large-scale operations for the production of tin from lode deposits were possible, it was recommended that the Bureau of Mines resample parts of Squaw Creek and conduct a mill test of lode material to determine whether a concentrate could be made that was high enough in tin and low enough in iron to be acceptable in American smelting practice. This work, under the supervision of Paul L. Russell, was begun in November 1942 and completed in January 1943, during which time the Sierra Metals Co. acquired control of a large area in Sawmill Canyon. At the suggestion of the Federal Geological Survey and the War Production Board, which had reason to believe that a great deal of commercial material existed on certain flatlands and gully slopes, the project was extended to include test pitting and sampling of those areas. This work was completed in February 1943.

May 1, 1947

By M. D. Johnson

Mina Santa Rosa, in west central Panama, is the first large-scale gold mine in Panama and will soon be the largest single-mine gold producer in central America (Fig. 1). At full production, the mine will process 1.8 Mt/a (2 million stpy) of ore and produce more than 1.8 t/a (60,000 oz/year) of gold and 9.3 t/a(300,000 oz/year) of silver. Mina Santa Rosa is a subsidiary of Greenstone Resources of Toronto, Ontario. Freeport-McMoRan geologists first visited the area in 1985. Their rock chip sampling adjacent to old shafts and adits confirmed widespread gold and trace element geochemistry anomalies. Surface mineralization appeared to be localized in and adjacent to narrow veinlets. However, they recognized astructural setting similar to the Nevada Tertiary volcanic-hosted epithermal gold systems.

Jan 1, 1996

By Sean Masse

New Gold?s New Afton Mine, located 8 km (5 miles) west of Kamloops, British Columbia, is a 4.5-Mt/a (5-million stpy) block cave mine, making it the highest tonnage underground hard rock mine in Canada. The reserve is estimated at 52.5 Mt (55.9 million st) with grades of 0.65 g/t (0.02 oz/st) gold and 0.93 percent copper (2012). Commercial production was achieved in July 2012 and nameplate production was achieved ahead of schedule in September 2012, with the cave breaching to surface in 2013. The mill has a SAG and a ball mill with a froth flotation circuit.

Jan 1, 2014

By Michel Grenier, Robert Scott, Mahendra Gangal, Andrew Dasys

This research project which took place at Brunswick Mining and Smelting's Brunswick mine, was undertaken to assess the ability of new diesel engine technology to meet current and anticipated underground worker exposure limits to diesel exhaust contaminants. Concentrations of CO, CO2 NO, NO2 SO2 and respirable combustible dust (RCD) were measured in a remote mine area where a haulage truck was operating under simulated duty cycles. The 26 ton haulage truck was equipped with a 300 hp, electronically controlled engine. Fresh air was supplied to the area as per the MSHA certification document for this particular engine. Results showed that while the vehicle operated in a normal and realistic duty cycle, the concentrations of contaminants remained well below the ACGIH guidelines for the threshold limit values (TLV)for exposure. While operating at 630/0 of maximum horsepower (26 tons of ore in the dump), the time-weighted average exhaust gases concentrations (CO, CO2 NO, NO2 and SO2) never exceeded 150/0 of their respective TL Vs. ReD concentrations in this instance were measured at 0.59 mg/mJ or 39.30/0 of the exposure limit suggested by the Canadian ad hoc Diesel Committee. The Air Quality Index was 1.55 or 520/0 of the maximum suggested value for exposure.

Jan 1, 1994

Jan 1, 2005

This paper presents the results of a unique study conducted by the National Institute for Occupational Safety and Health (NIOSH) from 2016 to 2019 to evaluate the effects of longwall-induced subsurface deformations on shale gas well casing integrity and underground miner safety and health. At both deep and shallow cover instrumentation sites, surface subsidence measurements, subsurface in-place inclinometer measurements, and underground pillar pressure measurements were conducted as longwall panels were mined. Comparisons of the deep and shallow cover test site results with those from a similar study under medium cover reveal an interesting longwall-induced response scenario. Under shallow and medium covers, measured horizontal displacements within the abutment pillar are one order of magnitude higher than those measured under deep cover. Conversely, measured vertical compressions under deep cover are one order of magnitude higher than those under shallow and medium covers. However, FLAC3D simulations of the casings indicate that, in all three cases, the P-110 production casings remain intact under longwall-induced deformations and compressions, which has serious implications for future mine design in areas where shale gas wells have been drilled ahead of mining.

Jan 7, 2020

By R. G. B. Pickering

The hard rock gold and platinum mines in South Africa have seen little development in the technology of mining. Holes are still drilled in the rock?though the latest water hydraulic rockdrills will complete that task in two minutes compared with the eight hours for hand drilling. Charging up is with far safer explosives and with available initiation systems it is no longer necessary to run up the face lighting each fuse. Movement of rock in the stope is predominately by means of scraper buckets and scraper winches?these were first introduced in the 1920s. Support is still mainly rock, either in situ pillars or backfill, or alternatively wood. Just as the mining process has changed very little it is hardly surprising that the productivity of mining is also relatively unchanged. Major efforts have been made to mechanize the mining process. However, most of the narrow reef mines where ?trackless mechanized mining? was introduced in the early1980s have reverted to conventional mining. In the wider reefs mechanized mining is the option of choice, unfortunately most of the gold and platinum mines have very narrow reefs that are not suitable to ?off the shelf? equipment. The move to introduce room-and-pillar mining into the narrow UG2 reefs is at the expense of mining more waste with the reef, fortunately it appears that appropriate waste and reef separation processes are available. Room-and-pillar mining followed by long hole drilling and blasting of a narrow slot of reef out of the pillars currently appears to offer the best of both worlds?maximum reef recovery with minimum waste dilution.

Jan 1, 2002

By Others, C. M. Weld

During the past two years the Bureau of Mines has issued a series of mimeographed reports giving the results of research work and experiments conducted as part of its war minerals investigations. In this bulletin the reports on manganese are presented, which range in scope from the beneficiation of the ore to the utilization of the metal. The bulletin is in eleven chapters, each comprising a separate report, arranged in the order given below. 1. General information regarding manganese, by C. M. Weld. 2. Uses of manganese other than in steel making, by W. C. Phalen. 3. Problems involved in the concentration and utilization of domestic low-grade manganese ores, by Edmund Newton. 4. Preparation of manganese ore, by W. R. Crane. 5. Leaching of manganese ores with sulphur dioxide, by C. E. Van Barneveld. 6. The Jones process for concentrating manganese ores; results of laboratory investigations, by Peter Christianson and W. H. Hunter. 7. Cost of producing ferromanganese ores, by C. M. Weld and W. R. Crane. 8. Production of manganese alloys in the blast furnace, by P. H. Royster. 9. National importance of allocating low-ash coke to the man- ganese-alloy furnaces, by P. H. Royster. 10. Electric smelting of domestic manganese ores, by H. W. Gillett and C. E. Williams. 11. Use of manganese alloys in open-hearth steel practice, by Samuel L. Hoyt. As each chapter was originally prepared as a unit, there is neces- sarily some duplication and overlapping. With certain exceptions, however, each paper is reproduced in practically its original form. In chapter 1, covering certain general phases of the industry, such as uses, specifications, prices, and statistics, the subject matter has been somewhat modified in view of changes in conditions.About 95 per cent of the manganese consumed in the United States goes into the manufacture of steel. The remaining 5 per cent is used in a number of minor industries, the chief of which is the manufacture of dry cells. These minor uses are described in chapter 2. No discussion of the geology of manganese eres is presented, but a short bibliography on the subject is appended. With few excep- tions the manganese deposits of the United States are irregular, pockety, and uncertain. Largely for this reason, mining methods are crude and hardly warrant descriptions. The concentration of manganese ores, however, is an important problem and involves some details not common to other ores. Chapter 3 discusses the concentration and utilization of low-grade ones, notes the relationship of concentration to metallurgical prao- tices, outlines concentrating processes, and treats of commercial problems. In general, as regards concentration methods, manganese ores may be divided into two groups, as follows: (1) Ores permitting mechanical separation of the manganese minerals and the gangue, and (2) ores in which the manganese minerals and the gangues are so intimately associated that separation requires some hydrometal- lurgical or pyrometallurgical process. Heretofore, attention has been confined almost wholly to mechanical separation, chiefly by gravity. In fact, so far as known, all production of concentrates has been by wet gravity methods, although during the war some companies investigated the commercial pessibilities of magnetic separation and reported favorable results, the construction of one magnetic con- centration mill being started. The usual wet gravity methods are described in chapter 4. During the war, the Bureau of Mines undertook investigations of methods applicable to ores of group 2. A hydrometallurgical process involving leaching with sulphur dioxide was studied at the mining experiment station of the bureau at Tucson, Ariz. The results of this work, presented in chapter 5, indicate that the process is metallurgically feasible but the cost makes it unattractive. The results of an investigation of a pyrometallurgical process known as the Jones process are presented in chapter 6. The process, which is still in the experimental stage, was found to be metal- lurgically sound. The manganese product is not a concentrate but an alloy, made directly from a lean unconcentrated ore. The custom- ary method is to manufacture alloys from high-grade ores or from concentrates of leaner ores. A discussion of the costs of ferro-grade manganese ores is pre- sented in chapter 7. This discussion is in general terms only, but should be of use in so far as it relates to competitive conditions.

Jan 1, 1920

By G. M. Bernard

The Andacollo gold mine is located near the small town of Andacollo, Chile (population 14,000) in the fourth region. It is approximately 35 miles by paved road from the coastal city of La Serena, and Santiago lies about 300 miles to the south (see map.) Site elevation varies between 3300 feet and 4200 feet. The climate at the site is moderate but arid, with an average annual rainfall of only five inches. Because there is little rain, and the temperature varies only a few degrees (57"F to 75°F); there are no freezing, solution dilution, or pad saturation problems. The climatic conditions are ideal for heap leaching.

Jan 1, 1996

By AIME AIME

WHEN "Chief" Buehler in mid-September set out on his official 10,000 mile swing-around-the-circle visiting Local Sections he decided not to tell his audiences how to organize and operate a state geological survey. As the director for 28 years, of the Missouri Bureau of Geology and Mines (which, he concedes, is the best in existence) lie could have done this to good advantage; but he preferred to discuss affairs of the Institute. In 25 speeches made to member and student groups, he dwelt on sonic or all of the following phases of activities. He stressed the vital importance of the Local Sections in providing the opportunity for members to associate under pleasant auspices with others in their profession. The benefits of Institute membership he classified as tangible and intangible. Of the two lie felt that the latter were more important. A man's progress in his profession depends in large measure upon a broad acquaintance and friendship with others. The Institute is incomparably the best medium for meeting fellow engineers. The primary, function of the new enlarged Membership Committee is to obtain a comprehensive list of engineers eligible to be members, always hearing in mind that the standards of membership must not be lowered in any degree. These men are to be invited by individual letter to apply for membership. Whether they become members or not is of less importance; but it is vital that no qualified man should be outside the fold for the reason that membership had never been suggested to him. Dr. Buehler emphasized repeatedly his feeling that the younger man that had never had Institute membership brought specifically to his attention had been cheated:

Jan 1, 1935

By Ernest W. Hilton

The purpose of this investigation was to assess the environmental impact of the surface mining methods currently used in the steep-sloped areas of Central Appalachia: southern West Virginia, eastern Kentucky, southwestern Virginia and northeastern Tennessee. Comparisons are made between mountaintop/cross ridge mining, contour strip, augering and an innovative method surface shortwall mining which was attempted at Julian, West Virginia. Included in this final report are a discussion and analysis of current Appalachian production, reserves, and the extent of land affected on a county- by-county basis. Additionally, the seams within the steep sloped region have been assessed according to minimal standards of thickness, surrounding lithology, and areal extent to determine their amenability to surface shortwall mining. These seams have been tabulated with their ash, sulfur, and BTU content on a county-by county basis. Only minimal statements are made concerning quantity because of the narrow set of conditions required by the shortwall method. Other sections deal with the possible technical failings of an operational surface shortwall system based on field studies at shortwall operations, discussions with people experienced with shortwalls and research into ground control problems at sites where short- and longwall operations have been monitored. A final section details proposed additional research directions which the Bureau might take in the future.

Jan 1, 1979