Search Documents

In the interest of safety in underground coal mining, the Bureau of Mines recommends: 1. That doors used to control ventilation (a) Shall be installed in pairs to form air locks, (b) Shall be self-closing, (c) Shall not have latches or other devices for holding them open, (d) Shall be constructed and maintained to prevent excessive air leakage through or around them, (e) Shall be fire resistant. 2. That wherever practicable the use of doors shall be limited to development openings. The Mine Safety Board is of the opinion that the best practice in coal-mine ventilation makes use of a split system employing overcasts or undercasts with doors limited as far as feasible to development openings. The distance between air-lock doors on haulageways should be sufficient to accommodate a trip or train of maximum length. Where auxiliary doors are installed to control ventilation during emergencies, they should be so placed that they can be utilized readily in case of damage to the air-lock doors.

Jan 1, 1938

Mineralisation was identified at Gladstone Hill as far back as the late 1870's û early 1880's, shortly after the initial discovery of Martha Hill. Indeed, early recovery problems from the Martha Hill mineralisation led to the preferred development of are bodies within what is now the Union Hill Joint Venture tenement; ore bodies such as Silverton, Amaranth, Union to name a few. Work at Gladstone Hill is carried under the Union Hill Joint Venture, a 50:50 joint venture between Auag Resources Ltd - manager (a fully owned subsidiary of Otter Gold Mines Ltd) and Welcome Gold Mines Ltd (a fully owned subsidiary of the Normandy Group). The joint venture participants also operate the adjacent Martha Hill operation. Mineralisation of Gladstone Hill, as with mineralisation at the adjacent Martha Hill, has been interpreted as a low sulphidation epithermal Ag-Au system hosted within hydrothermally altered andesites of the lower Coromandel Group. Drilling in recent years has successfully identified extensive mineralisation associated with the Gladstone vein set and the more recently identified high grade Moonlight Lode. Veining ranges in character from thin stock works to broader lode-style banded chalcedonic to cherty quartz. Visible gold is rare, with mineralisation generally associated with very fine-grained pyrite, arsenopyrite and minor electrum. The potential for the Gladstone Hill area is yet to be clearly defined as drilling to date has yet to close off mineralisation both along strike and down dip. If further drilling is successful, the joint venture partners believe Gladstone Hill could contribute significantly to the economic future of current operations.

Jan 1, 1999

The Mine Safety and Health Administration (MSHA) defines an independent contractor as any person, partnership, corporation, subsidiary of a corporation, firm, association or other organization that contracts to perform services or construction at a mine. Contractors that perform specific types of work are required to report the number of employees who work at coal mines and noncoal mines.

Jan 1, 2008

By J. M. Schaekers

In the first part of the article, the authors give a broad overview of the chemistry and some engineering aspects of bioleach processes, eventually leading to the important and critical issue of the stability of arsenic-containing residues, especially those derived from bioleaching of sulphidic gold ores. In the section ?Factors affecting arsenic stability? they give an excellent summary of the factors normally affecting the stability of such residues. This is followed by some valid comments on the suitability of a single leach test to evaluate the long-term stability of solid waste streams. However, they fail to mention that, up till now, no tests procedure has been accepted by either environmentalists or the mining/processing industry as a valid method to test the long-term stability of solid wastes. Their own method is no exception, although, like many others, it is useful to identify potential problems with solid wastes considered for disposal.

Jan 1, 2001

Jan 1, 1970

By J. P. Piguet, Y. Wileveau

ABSTRACT : An experimental programme for damage assessment was performed in the vicinity of the main shaft of Andra’s Underground Research Laboratory, currently under construction in the East of France, when the shaft is crossing the Kimmeridgian marls between 80 and 100 m depth. The mechanical behaviour was analysed by mean of convergence and displacement measurements. The disturbance into the wall was assessed using numerous methods such as measurement of sonic velocities, permeability measurement and VSP measurement in radial boreholes. The intensity of the damaged zone is low, and its extension does not exceed 0.5 time the radius of the shaft. It does not seem to depend on blasting patterns. ZUSAMMENFASSUNG : Ein Forschungs- und Versuchsprogramm wurde aufgestellt, um die beschädigte Zone im Bereich der Kimmeridgemergel zwischen 80 und 100 Meter Tiefe beim Zugangsschacht des im Bau befindlichen Andralabors im Osten Frankreichs zu berechnen. Das mechanische Verhalten der Formationen wird auf der Grundlage von Konvergenz- und Verschiebungsmessungen ermittelt. Verschiedene Messmethoden, wie z.B. mikroseismische Geschwindigkeite Messungen, Permeabilitäs- und Beschleunigungsbestimmungen in strahlenförmigen Bohranordnungen, erlaubten die Ermittlung des Beschädigungscharakters der Schachtwand. Die Intensität der beschädigten Zone ist niedrig, ihre Ausdehnung übersteigt nicht die Hälfte des Radius des Zugangsstollens und scheint unabhängig vom Schema der Sprengstoffanordnungen zu sein. RESUME : Un programme expérimental visant à évaluer la zone endommagée autour du puits d’accès du Laboratoire de Recherche Souterrain de l’Andra actuellement en construction dans l’Est de la France a été mis en œuvre lors de la traversée des marnes du Kimméridgien entre 80 et 100 m de profondeur. Le comportement mécanique des formations est évalué à partir de mesures de convergence et de déplacements. La mise en œuvre de nombreuses méthodes, telles que des mesures microsismiques, des mesures de perméabilité et d’accélérométrie en forages radiaux, a permis de caractériser l’endommagement en paroi du puits. L’intensité de la zone endommagée est faible et son extension ne dépasse pas 0,5 fois le rayon du puits. L’endommagement semble indépendant des schémas de tirs testés.

Jan 1, 2003

By L Olivier, R J. Lowther, J L. Lett, I Brunton

Hydraulic fracturing to precondition the orebody to enhance rock mass cavability is gaining acceptance in underground cave mining applications. Assisting cavability is becoming important as an increasing number of cave mines are being implemented in hard, deep and competent rock masses where clamping stresses are higher and cave column heights may be in excess of 1000 m. Propagating large caves to surface in such conditions can be challenging as risks such as slowed propagation and air gaps can develop during the process.Underground-based hydraulic fracturing is routinely used at Cadia East as a means of preconditioning the orebody to assist in cave propagation, fragmentation and seismicity reduction. This paper presents a summary of a surface-based hydraulic fracture program that was successfully implemented to assist in the propagation of the Cadia East Panel Cave 1 (CE-PC1) cave to surface through competent overlying rock masses. In this case study, the propagation of the CE-PC1 cave slowed as the cave grew past 750 m in height, initiating a Trigger Action Response Plan regarding the cave propagation rate. Surface-based hydraulic fracturing was subsequently used to stimulate the cave to propagate through the final 450 m to surface. The paper details the equipment, strategy, implementation and risk management involved in the program as well as the key learnings.CITATION:Lowther, R J, Olivier, L, Lett, J L and Brunton, I, 2016. Implementation of a surface-based hydraulic fracturing program to successfully propagate a large cave through hard, competent near-surface rock masses to achieve breakthrough, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 83–96 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

The corrosion behaviour of a low carbon steel was investigated in natural seawater and various synthetic seawaters. It was found that the steel corroded nearly four times faster in a 3.5% NaCl solution than in natural seawater for an exposure time of 21 days. The corrosion rate after immersion in synthetic seawaters (ASTM D1141 and Marine Biological Laboratory seawater) is similar to the corrosion rate after immersion in natural seawater. Calcium carbonate (aragonite) deposits were found on the surface of the steel after immersion in natural seawater and the synthetic seawaters. Some magnesium-containing deposits were also found after immersion in the natural seawater. These deposits act as a barrier against oxygen diffusion and thereby lower the corrosion rate. The morphology of the calcium carbonate deposits that formed during immersion in the natural seawater is different from those formed during immersion in the synthetic seawaters. This may explain the slightly lower corrosion rates obtained in the natural seawater. X-ray diffraction also showed that the oxy-hydroxides formed in the 3.5% NaCl solution differed from those formed in the other solutions. Keywords: Corrosion, seawater, low carbon steel, 3.5% NaCl, aragonite

Jan 1, 2006

By Kot F. Unrug

Strength of coal is one of the governing factors in size determination of mine pillars, and therefore affects the percentage of extraction and thus, utilization of reserves. Coal strength is also important from the subsidence control standpoint, where mine pillars with appropriate safety factors should be designed for long term stability. Determination of coal seam strength has been addressed through the extrapolation of the coal strength obtained from a small number of samples on the whole section of the seam. This procedure often gives unreliable results. Presented in this paper is a method of in-situ strength testing of coal, allowing for a realistic determination of seam strength. Results of a field case study dealing with the coal seam, where samples for the laboratory strength tests could not be obtained due to the dense cleat, are presented. However, in these conditions, the in-situ testing was successful. A comparison of both conventional and the in-situ penetrometer method was carried out. It was found that the penetrometer data not only improve the accuracy of strength determination of the entire seam, but also prove to be much more cost effective than the conventional method on a per test basis.

Jan 1, 1995

By P Phelan

This paper presents the general background and development of raiseboring followed by case histories of circumstances where raiseboring equipment was used in a different manner to normal. Each project has been summarised for this paper as described below: Case 1: Retrieval of a 40 tonne truck from a stope at Peak Gold Mines. Case 2: Slot raising - Conventional, Uphole and Downhole Reaming at Peak Gold Mines. Case 3: Reamer recovery by Downreaming at Tower Colliery. Case 4: The importance of Mucking Raisebore Holes û Thalanga Project. Case 5: Pilot Drilling Dewatering Holes at Beaconsfield Gold Mines. Case 6: Low angle æcut offsÆ in vein at Telfer Gold Mine.

Jan 1, 1998

By G. S. Littlejohn

Following study of historical South African practice and a review of recent experience gained during the design, construction and testing of the high pressure plugs at the South Deep Water Barrier Project, this paper makes recommendations to improve practice. Initially, site investigation requirements are described with reference to geological, hydrogeological and seismic considerations, including site preparation and pre-grouting of the surrounding rock mass, if permeable. Structural and hydraulic aspects of plug design address topics such as residual permeability, aggressive mine water, plug materials, mortar strength and bleed. In situ thermocouples and piezometers are recommended to optimize the timing of plug tightening and monitor plug performance during service. Plug construction covers aggregate preparation, mortar quality control, plug tightening grouts, injection pressures, records and the overriding need for a method statement specification to control all aspects of plug construction. On completion of the plug, tests to establish surrounding rock stress regime, plug strength, and residual permeability are described to enable a comparison with original design assumptions. Monitoring and maintenance procedures are proposed to ensure satisfactory long-term performance of the plugs.

Jan 1, 2006

By Mike D. J Bonneau, Malcom Jr Ford

Rietspruit Opencast Services was one of the first opencast coal mines to successfully employ cast blasting to aid in the burden removal operation. Initial work on cast blasting began at the mine in 1980 and has developed to a stage where approximately 26% of the total burden material is cast to a point where handling by draglines is no longer required.

Jan 1, 1991

By E. L. Affleck, W. G. Stevenson

In both Canada and the United States, a company making a public offering of securities must comply with regulations which have been passed by Federal, State and/or Provincial Legislatures. These regulations usually require the distribution of an acceptable prospectus which provides essential background information about the issuer, the project and the share offering. when the public offering has been accepted, the unlisted company may then seek a listing of its shares for trading on a Stock Exchange. Once listed, the company will be subject to rules of the Stock Exchange. This paper will deal with the specific information required for inclusion into a prospectus being submitted for a resource company and particularly those parts of concern to mining engineers and geologists.

Jan 1, 1985

This study was conducted to determine the effects of a machine-mounted scrubber and water sprays on face methane levels. Testing was conducted in the NIOSH ventilation test gallery which was designed to simulate a full-scale mine entry. In the test entry, a model mining machine, equipped with water sprays and a simulated dust scrubber, was located at the face of a 20-ft box cut. Blowing ventilation was provided using a curtain with a 40-ft setback distance. Methane released from a pipe manifold located inby the mining machine was monitored at six locations that were 1 ft outby the pipe manifold. Tests were first conducted to evaluate the effects of using sprays and scrubber separately on face methane levels. Additional tests were conducted to determine how a scrubber used with various water spray systems would affect face methane levels. The use of either sprays or scrubber reduced face methane levels significantly. The combined use of sprays with the scrubber further reduced face methane levels a small amount. Primarily the sprays affected methane levels by changing airflow distribution close to the face.

By D. Pillay

Outsourcing? and ?sub-contracting? have become buzzwords in recent years, as SA industry becomes increasingly exposed to the global economy, and global competitiveness. In its effort to ?catch up? after years of relative isolation, there is a concerted effort to learn from global ?best practice?, in order for South African companies, and the SA economy, to become ?winners?. There seems nothing wrong with this approach at face value. Companies need to compete and be profitable if they are to remain in business. Failure will in the end mean bankruptcy, and the loss of jobs. However, if one interrogates the precise practices, and their implications for all concerned?not just shareholders and employers, but workers, communities, the environment, future generations, the national economy?then the picture can change dramatically. ?Best practice? for whom?

Jan 1, 1999

By John Nagy, Hylton R. Brown, Irving Hartman

"INTRODUCTION The tests described in this publication were planned to provide information on the explosibility of metal-powder dust clouds. This subject has become increasingly important because of the large quantity and variety of metallic powders now used for military and industrial purposes. To provide the increased amounts of metallic powders needed in the manufacture of munitions and to supply the demand created by the rapid growth of powder metallurgy, existing metal-powder plants have been enlarged, production schedules accelerated, and new plants erected. In some cases new methods of producing metal powders have been developed. This increased production and the development of new manufacturing methods have caused an increase in the number of metal-powder fires and explosions, with accompanying heavy loss of life and property. These have emphasized the need for information on methods of providing protection against hazards inherent in the production and handling of powdered metals. This paper gives results of laboratory inflammability and explosibility tests made to April 1, 1943, and is a progress report. Many descriptive details have been omitted purposely; they will supplied in a later publication, expected to be a Bureau of Mines bulletin."

Oct 1, 1943

By L. F. Bishop

THE ore bodies of the Butte district1 are found in many different vein systems having many different structural characteristics; some are narrow with self-supporting ore but with weak walls; some are wide with weak or strong ore and weak walls; some of the veins dip steeply and others do not; some have well defined walls, and others, in the "horsetail" area, are mined to sample limits. Consequently, many types of stoping methods are used in mining these ores. The stoping methods used in the Anaconda Copper Mining Company's properties are the square-set and cut-and-fill. The square-set method is the principal stoping method used because, generally speaking, the ore and walls are weak, the ore is high grade, and good extraction is required. These square-set stopes may be classified as conventional, vertical slice, slot, timber rill, and Mitchell slice types. The conventional type square-sets are those of various shapes and sizes, mined by horizontal slicing to the boundaries of the stopes. The rock is slid to the chute and the filling is moved by gravity. The ore and waste may be handled with a scraper when local conditions require it. The vertical-slice square-set system is the type used in narrow veins that are mined in vertical panels. The slot stopes are stopes in wide veins that employ a slot across the vein instead of a con- ventional chute to handle the ore. The timber rill fs a type of square set in which the ore is mined as in inclined cut and fill but the square-set timber is used. The Mitchell slice is the type used for some broken or heavy ore blocks, or for pillar extraction between two converging slot stopes. The cut-and-fill method is used where the ore will stand without much support although the walls may be weak. The principal type of this method is the horizontal cut-and-fill, with mechanical scraping. The inclined cut-and-fill, or rill, stopes are used in some veins too narrow for scraping. The production from the various meth: ods in use for the second six months of 1944 are shown in Table I. [ ] This paper deals mainly with the vertical slice and slot types of square-set stoping, because of their effect on production locally and their potential possibilities here and in other districts, with sufficient reference to conventional square-setting for comparison.

Jan 1, 1945

By James A. Wasson

This report summarizes the results and conclusions reached by various investigators who have attempted to determine the extent to which hydraulic fracturing will affect the secondary recovery of crude oil by waterflooding. It also discusses the most advantageous use of this well-stimulation method in waterflood projects. A thorough search of the literature was made, and pertinent information was abstracted from appropriate reports. A carefully designed and controlled program of formation fracturing is an effective aid in waterflooding because it increases water-injection and oil- production rates. Generally, fracturing has resulted in little or no reduction in ultimate oil recovery, but under certain circumstances recovery has been substantially increased.

Jan 1, 1963

Mineral liberation data are routinely obtained for a wide variety of applications, including ore characterization and characterization of various metallurgical test products obtained in bench-scale laboratory testwork. Newmont Mining Corporation owns several properties in the Carlin Trend containing refractory gold ores. These ores are generally difficult to treat and have to undergo several processing stages for gold recovery. At Carlin?s Mill 5 operation, flotation is used to pre-concentrate some of these difficult ores to produce a sulfide concentrate to feed the roaster. It is of interest from a flotation perspective to be able to study the floatability of pyrite, arsenopyrite and arsenian pyrite, since these minerals all have different quantities of gold associated with them, and have to be recovered to ensure a successful separation has been achieved. In this paper, a detailed MLA study on several Carlin ores was undertaken on samples from flotation tests, using air or nitrogen as flotation gas, specifically to study the differences in floatability characteristics, which ultimately impacts overall gold recovery. I

Jan 1, 2009

By T. Clarkin

This paper presents a hydrologic closure design concept to minimize the risk of water discharges from closed mine tailings facilities. It evaluates the applicability of U.S. Nuclear Regulatory Commission guidelines to develop acceptable designs for the closure of tailings facilities that have a calculated adequate surcharge capacity for environmental protection and an emergency spillway for dam safety. The guidelines provide a basis to estimate an acceptable surcharge capacity of a Probable Maximum Flood series for storage of surface runoff. To be conservative and for redundancy with respect to dam safety, an emergency spillway is provided to pass the Probable Maximum Flood. Depending on the annual water balance, the surcharge capacity may be used by surface runoff and minor amounts of sediment that accumulates in the impoundment from year to year. The emergency spillway crest is then set at this level or above the surcharge capacity, whichever is higher. An example is given of the active Red Dog Mine tailings facility in Alaska where this method was used for the preliminary design of the tailings main dam at its ultimate closure configuration.

Jan 1, 2012