Search Documents

The major proportion of South African coal is extracted by the bord-and-pillar mining method which requires that the overlying strata be supported by pillars of coal. The stability of the pillars is a major safety concern. One of the factors which affects the strength of coal pillars is the intensity and nature of discontinuities in the coal seams. Current design methods for pillars assume that al the coal seams have equal strength and are equally disturbed by natural discontinuities, resulting in over-designed pillars in some cases and potentially unstable pillars in others. Research was carried out to determine the nature of discontinuities in coal seams and to assess their potential effect on pillar strength. It was found that large variations exist in the intensity of discontinuities in the different coal seams being mined. In addition, numerical model studies showed that the discontinuities could significantly reduce pillar strength if the width-to-height ratio of the pillars is small, but the effect decreases as the width-to-height ratio increases.

Jan 1, 1997

By C. Patrick

Longwall face-to-face transfers can cost over $100 per minute in lost production potential and $100,000 for personnel and supplies. Such high cost makes extensive planning and control of the transfer process a critical necessity for the economic feasibility of longwall operations. This paper reports operations research techniques used for the analysis and modeling of longwall face-to-face transfers. Transfer data has been collected from companies who operate over 30% of the total U.S. longwall faces. Comprehensive sequence networks of existing longwall transfers were developed; simulation models of transfers under varying conditions were generated; and, the economics of general transfers and time-cost tradeoffs in the transfer procedure were investigated.

Jan 1, 1993

By Kyle W. Charlton

The Bureau of Mines utilizes special testing methods for the analysis of underground mine atmospheres for use during or after mine disasters and fires. These methods depend upon drawing sample gas to the surface through multiple tube bundles with the subsequent analysis of grab samples or the automatic analysis by often remotely located instruments on a continuous, 24-hour basis. During cold weather, low ambient temperature causes condensation and freezing of condensable vapors in the sample which can result in delayed response times or complete blockage of the sample line. This report covers research and resulting development conducted by the Bureau of Mines to produce a reliable method to selectively remove condensable vapors and particulate in the sample gas stream under worst-case field conditions. The effort resulted in two prototype systems which have greater field utility than originally anticipated. The innovative project resulted in two patent applications submitted through the Bureau of Mines.

Jan 1, 1981

By R. Banda

This paper describes the decision to implement and then the implementation itself, through trials, of electronic ?Smartdets? over previously used shock tubes. It concludes that Mufulira Mine has become the first mine in Zambia to convert 100% of its stoping to ?Smartdets?, because the Mine?s management was prepared to look beyond the unit cost of product and were ready to look at the broader picture of cost effectiveness and increased productivity.

Jan 1, 2005

By M. Lu, E. Broch

Abstract: The formation and mechanism of rock cavern roof arches are studied and effects of rockbolts reinforcement are evaluated. It is concluded that a self-supported roof arch may be formed by the excavation. To stabilize such a roof arch, fully grouted rockbolts are effective. Tensioned cable anchors may have a negative influence on the arch stability. Zusammenfassung: Die Formation und der Mechanismus von Deckenbögen in Bergkavernen wird studiert und der Effekt von Verstärkung mit Bergbolzen wird bewertet. Es wird festgestellt, dass die Exkavation einen selbst-stützenden / freitragenden Deckenbogen formen kann. Eingegossene Bergbolzen sind effektiv um einen solchen Deckenbogen zu stabilisieren. Spannkabel können unter Umständen eine negative Einwirkung auf die Stabilität des Bogens haben. Résumé: Le mécanisme et la formation de voûtes dans les cavernes rocheures sont étudiés et l'effet du renforcement par boulonnage est évalué. Nous arrivons à la conclusion qu'une voûte autosupportêe peut être formée par excavation. Des boulons entièrement scellés par coulis de bêton s'avèrent efficaces pour stabiliser de telles voûtes. Les tirants d'ancrage peuvent quant à eux nuire à la stabilité de la voûte.

Jan 1, 2003

By Jeffrey Mitsopoulos

King County?s (KC) Brightwater Conveyance Project in Seattle, Washington involves the construction of approximately 21 kilometers (13 miles) of bored tunnel, in three contracts, with four TBM?s which produce large amounts of real-time digital mining data. To facilitate the management of TBM data with a single interface and assist in project Quality Assurance, KC?s Construction Manager (Jacobs Engineering) recommended the use of the software TPC (Tunneling Process Control), developed by Babendererde Engineers GmbH. The paper demonstrates how TPC was used for oversight, analysis and QA on a complex tunneling project and how contemporaneous review and management of data results in a better understanding of TBM performance than can be obtained by retrospective analysis of data.

Particle Mechanics and the Design of Cyclone Tribochargers Triboelectric separation is a dry electrostatic technique that has shown promise in several particle processing applications. A tribocharger uses contact or friction to differentially charge particles of different materials, which are then separated by an electric field. The initial tribocharging process is poorly understood, with tribocharger design and operation largely a matter of trial and error. A better physical understanding of tribocharger operation would therefore be of immense value in the optimisation of triboelectric separation processes. A combination of charge measurements, trajectory modelling and high-speed video has been used to relate charging to particle mechanics in a cylindrical pneumatic cyclone, one of the most effective tribochargers for mineral separation applications, and the preliminary results are presented here. The consequences of these observations for cyclone tribocharger design and operation, and for tribocharger design in general, are discussed.  

Sep 13, 2010

By Z. A. Md-Nor

Risk management is an established loss-control methodology that has been applied successfully in many industries. Recently, interest in this structured approach has grown in the mining industry. The main objective of this research was to develop a risk-assessment process, which is a part of risk management, that can be used by the U.S. mining industry to more thoroughly characterize risks associated with haul truck-related fatalities. The assessment is based on historical data obtained from the U.S. Mine Safety and Health Administration (MSHA) investigation reports, which includes 113 fatal incidents that occurred from 1995 through 2006. The risk-assessment process used in this research involves the following basic steps: identification of the risks, risk analysis and risk evaluation. The preliminary hazard assessment (PHA) method is used in identifying and quantifying risks. Risk levels are then developed using a pre-established risk matrix that ranks them according to probability and severity. The resulting assigned risk value can then be used to prioritize control strategies. This paper is a part of a detailed study on risk assessment for equipment-related fatalities in mining sponsored by the Western U.S. Mining Safety and Health Training and Translation Center.

Jan 1, 2008

Grade uncertainty can have a number of important implications for a mining operation. One of the most significant risks in not considering grade uncertainty in planning is the over or under allocation of processing or mining capacity when compared to realised grades. This could lead to wasted capital expenditure or missed opportunities to add value. This paper demonstrates a method that optimises production capacity and mining schedules in the presence of grade uncertainty. Applying this method to the case study of a nickel deposit recommended a reduction in processing capacity, an increase in mining capacity and more extensive utilisation of stockpiles than optimisations completed with traditional methods. As a result, average NPV improvements of between seven per cent and 27 per cent were gained.

Dec 6, 2010

Efficacy of Enhanced Gravity Separator in Processing Indian Iron Ore Slime The slime sample was subjected to concentration using Falcon concentrator for their enrichment. The effects of three important variables, eg bowl rotation frequency, back water flow rate and per cent solid were studied on the process performance. Increasing the rotation of the Falcon bowl, enable more material to the underflow by increasing the yield, whereas, the iron content decreases steadily with increasing the rotation of the bowl. The increase in the back water flow effectively removes the clay materials from the underflow at the expense of the yield. Similarly, increasing the per cent solid concentration in the feed produces a better product both in terms of yield and Fe content. Results show that EGS/Falcon can be used for processing Indian iron ore slime and producing pellet grade concentrate.

Sep 13, 2010

By X. Shi

This paper presents design and implementation details of a fuzzy-behavior-based controller for an automated excavator. The robotic excavator is equipped with sensors, actuators and an embedded control system. The excavator controller uses neural-networks to interpret forces and torques gathered during the excavation process from bucket-mounted force sensors. Implementation details card experimental results using the fuzzy-behavior-based excavation controller are given for several excavation tasks. These excavation tasks demonstrate some of the complex skills that are essential for an autonomous mining-excavator controller.

Jan 1, 1997

By Robert P. Vinson

This Bureau of Mines report presents the results of tracer gas studies conducted at three facilities where bagger hoods had been installed several years ago to remove airborne silica dust from the vicinity of the bagging operator. The studies indicated that for optimum benefits makeup air must be evenly dispersed, the hood enclosures and duct systems must be as airtight as possible, the average intake air velocity of each hood should be at least 200 fpm, and the hoods and duct systems must be properly maintained.

Jan 1, 1981

By Paul H. Lu

Methods and results of measuring three basic parameters for ground stability control, ground pressure, strata movement, and geomechanical properties of mine rock are presented in this paper. It is found that these parameters can be measured in situ by simple and practical techniques with nonsophisticated and inexpensive instruments. Specifically, a drillhole dilation technique employing a cylindrical hydraulic borehole pressure cell (CPC) was used to determine the modulus of rigidity. Premining ground pressures were determined by pressure convergence tests with a combination of one CPC and two pre-encapsulated flat hydraulic borehole pressure cells (BPC) installed in a single drillhole. Abutment pressures and pillar loading were monitored with BPC's. Differential strata movements and bed separations were measured with self-recording 10-anchor-point extensometers. Roof-to-floor convergence was measured with self-recording convergence meters. Some applications of these in-situ-determined parameters to mine design and ground stability control are also discussed.

Jan 1, 1984

By I. L. Whyte

apparent density and drag coefficient of porous ores on

Apr 1, 1995

By Kenneth J. Miller

The Bureau of Mines two-stage coal-pyrite flotation process was modified to provide a more concentrated final clean coal slurry underflow which could be dewatered economically by filtration or centrifugation. This was accomplished by doing the first-stage coal flotation step in the conventional manner with a slurry of about 8 percent solids, but running the second-stage pyrite Flotation step with undiluted coal froth concentrate containing about 25 percent solids. The final clean coal underflow produced by the new technique contained between 26 and 30 percent solids; this pulp was sufficiently concentrated to be filtered industrially without further thickening. Sulfur removal was equal to that obtained using dilute second-stage pulp,

Jan 1, 1975

By T Haskell, Y Joe, S Dickie

A current trend amongst producers is the increase in dewatering of iron ore fines (<0.5 mm), due to an increase in wet beneficiation processes used to upgrade lower quality ore deposits, increased water content in orebodies located below the water table, and increasing focus on transportable moisture limits (TML). Vacuum filtration is commonly used for dewatering of iron ore fines, and as with all filtration processes performance decreases with particle size. Significant improvements are possible with the use of filter aids, usually anionic surfactants and flocculants. Anionic surfactants reduce the surface tension of the associated water, which is then removed more readily leading to improved filtercake moistures. Anionic flocculants used correctly can improve cake permeability, in turn, decreasing cake formation times and increasing filtration rates. In addition to increased throughput, savings and benefits for producers can include: moisture limit penalties, improved handleability, along with energy and water savings.The effect of filter aids on two iron ore fines samples from the Pilbara region were evaluated using a lab scale vacuum filtration unit. The first sample showed a reduction in the filtercake moisture content by 2.3 per cent weight/weight (w/w) with the use of BASF’s Drimax® 1234. For the second sample a reduction in the filtercake moisture of 3.4 per cent w/w along with an increase in filtration rate of 20 per cent was achieved by using a combination of Magnafloc® 5250 and Drimax® 1239 NF, as both filter throughput and cake moisture were considered important by site.CITATION:Haskell, T, Dickie, S and Joe, Y, 2017. The use of filter aids on iron ore fines, in Proceedings Iron Ore 2017, pp 183–186 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By J. G. Wiese

Reagents are added to the flotation process of Merensky Reef ores to achieve specific functions that enable the separation of valuable minerals from gangue minerals on the basis of the difference in their surface properties. However, due to the complexity of the process, the various interactions that occur as well as the incomplete liberation of the ore and range of minerals present, it is difficult to quantify the behaviour of each of the reagents. More specifically, changes made to achieve a particular outcome may have secondary effects that can override the desired effect. If all the effects and interactions can be accounted for, it is possible to manipulate reagent suites and obtain better overall metallurgical performance. This paper discusses the effect of the addition of copper sulphate at different operating points of the recovery of the sulphide minerals. Batch flotation tests indicated that the recovery of chalcopyrite was not affected when operating conditions were varied, whereas pentlandite recovery was strongly affected by the point of reagent addition, and pyrrhotite recovery was enhanced by copper sulphate addition, irrespective of the point of addition, with the extent being dependent on the ore source. Floatable gangue was activated by copper sulphate in the presence of the dithiophosphate collector. Froth stability was also affected by copper sulphate addition.

Jan 1, 2007

By B. Oraee

Tunnels as any other structures are affected by different loads and stresses. Generally, the loads on tunnels consist of both static and dynamic loads. These loads must both be considered in the tunnel design process. In this paper, the stability state of Jiroft water-transform tunnel is evaluated. Firstly, the in-situ stresses and then using Kirsch?s equations the induced stresses due to static loads in walls and crown of tunnel are calculated. Consequently, the strain caused by probable earthquake without considering the interaction between the concrete lining of tunnel and rock mass using seismic analysis is calculated based on free-field deformation. When the strain is determined, the simplified method of closed-form solution, Wang?s equations and Penzien?s equations are used to estimate the applied forces on the tunnel due to earthquake such as axial force and bending moment on a tunnel section taking into account the interaction of the tunnel concrete lining and rock mass. Results of this study show that the loads applied to the tunnel as a result of earthquake waves can be affect the stability of underground structures, especially long structures such as tunnels.

Jan 1, 2011

By G. A. Craig

The Moon, asteroids, and planets of the solar system represent the most distant caches of wealth that humanity has ever considered recovering. Yet, in addition to the potentially recoverable values represented there, harvesting off-Earth resources has a second, almost incalculable sustainable benefit in that they can be retrieved with absolutely no damage to Earth. Previous research mostly assessed the potential of asteroids and the Moon for mining purposes from a theoretical and scientific point of view. These studies investigated drawbacks that could be experienced in this type of operation, but no detailed economic evaluation that is meaningful for mining project management has been conducted and the parameters that are most likely to make an operation feasible are unknown. This paper provides a preliminary economic and sensitivity analysis of a possible off-Earth mining business extracting minerals from an existing asteroid.

Jan 1, 2014

Water represents 80?85% of the volume of mineral pulp processed in flotation circuits. Imperatives for a more detailed focus on circuit water quality and its control have come from increasing requirements to use relatively impure primary water supplies (e.g. high salinity, treated sewage) and high proportions of recycle from tailings dams, thickener overflows, dewatered and filter products. An integrated methodology for examining process water quality and its effect on minerals separation has been developed coupled with minerals surface chemistry across the complete processing circuit. Unrecognised factors, including varying proportions of water streams (daily or hourly), colloidal precipitation, highly variable pH and Eh, reaction and dissolution of minerals, minerals surface layer coatings, residual reagents and their reaction products, and microbiological activity have been studied in eight mineral processing circuits. The methodology combines: solution survey and modelling; microbiological surveys; minerals surface analysis and modelling; and process response. It has been possible to match the predicted (model) pulp chemistry with that measured from surveys of the solution and mineral surfaces. Treatment methods have included: monitored and balanced stream combinations; organic species removal; flocculation and aggregation; induced precipitation; dissolved air flotation; ageing (oxidation, UV exposure); and chemical surface conditioning of minerals. Some specific achievements from the methodology applied in plant and laboratory testing, with examples from case studies, will be described.

Jan 1, 2001