Search Documents

By Peter Moser, Frank Chiapetta, Sacha Diaj, Florian Bauer

Good toe breakage and a flat working bench after blasting are important parameters to achieve a high productivity during material loading and reduce the necessity for secondary blasting. Good toe breakage requires a proper burden – side spacing design and a suitable sub-drilling. With unfavourable jointed rock mass conditions the use of horizontal bottom holes still can be found as common work practice even that this is associated to high risks.

Jan 1, 2009

By B. J. Moore

This publication contains 14,242 analyses of gas samples from oil and gas wells and natural gas pipelines in 40 States and 24 foreign countries. These gas samples were collected in the period 1917-85 as part of the Bureau of Mines survey for helium occurrences. The gas analyses contained herein were made by several methods over the period covered. Analytical work on samples collected early in the period was done on the Orsat apparatus. The one-cut apparatus and four-cut fractional distillation equipment were added later. A mass spectrometer was acquired in 1949 and used for all gas analyses made after that time. From 1917 to 1978, helium analyses were made on special helium analytical equipment designed and built by the Bureau of Mines Helium Operations Laboratory. In 1978, this apparatus was replaced in the quantitative helium analysis work by a gas chromatograph.

Jan 1, 1987

Integrated Utilisation of Desulfurisation and Skimming Slag

Sep 13, 2010

Lower Miocene Maryville Coal Measures at Waitewhena Coalfield, in the Taranaki coal region, include seams of sub-bituminous coal up to 4 m thick. During coalfield exploration Fletcher Challenge Ltd drilled ten cored holes, all of which encountered at least one seam. Coal quality is variable. Ash ranges from six to 12 per cent and sulphur from 0.5 to three per cent. A basal seam, overlying the Lower Mokau Sandstone, appears to extend throughout the area under investigation. A rider seam, of variable thickness, closely overlies the main seam in most drillholes. The rider converges with the main seam to the north and vertical trends in coal properties suggest that the seams are united in some locations. A less extensive seam sometimes occurs at the top of the coal measures beneath the Upper Mokau Sandstone. The lithostratigraphy of the intervening coal measures is complex, and coexistence of fluviodeltaic, lagoonal/lacustrine, and marine depositional environments is provisionally inferred. Lateral variations in coal properties (clastic derived ash, volatile matter, inertinite, hydrogen), thickness of the sedimentary parting between the basal seam and rider, texture of the coal measure sediments, and distribution of the upper seam all indicate persistence of a relatively low lying northeast-trending zone which may have been structurally controlled. Available data indicate that coal measure accumulation was terminated by marine transgression from north to south.

Jan 1, 1987

By M. Mead, J. Dumouchel, W. Yule, J. Giroux

The QMM mineral sands of South East Madagascar contain approximately 1,900 million tonnes of mineable sand with a total heavy mineral (THM) content of roughly 4.5wt%. The QMM deposits are the world’s largest known reserves of 60% TiO2 ilmenite and also contain a small volume of zircon. The deposits are semi-continuous and homogenous and the mineralized sands are free flowing with minimal overburden, induration & slimes. These characteristics are favourable to dredge mining and allow the application of conventional wet gravity, electrostatic & magnetic separation to final products. A mature THM mineral suite of high valuable heavy minerals (VHM) content has enabled the development of a relatively simple separation process.

Jan 1, 2005

By Brad Thrall, Howard Bradley, Michael Samuels

"LOCATIONViceroy Minerals Corporation owns and operates the Brewery Creek heap leach gold mine located approximately 55 kilometers northeast of Dawson City, Yukon Canada. Dawson was home of the Klondike Gold Rush 100 years ago. Upon startup in November 1996, the Brewery Creek Mine was the northernmost operating heap leach gold mine in North America and one of the most northern in the world. Located at 64"" 02' latitude, the mine is less than 300 km south of the Arctic Circle. Access to the mine is available at Kilometer 14 of the Dempster Highway, linking Inuvik, NWT and the Klondike Highway, 40 kilometers east of Dawson City. The immediate vicinity is the only part of Canada not glaciated in the Wisconsin advance, which has resulted in an oxide ore deposit due to approximately 80,000 years of weathering - an area unique in Canada.DESCRIPTION OF OPERATIONSIn order to utilize heap-leaching technology successhlly in an extreme northern climate, a number of design features were incorporated into the process flow sheet to operate on a year round uninterrupted basis. Winter temperature may dip below minus 50 ""C, demanding an approach to mining and leaching that is different from heap-leach operations in more temperate climates. Because of the severe winter temperatures, the mine operates approximately 2 10 days per year, while the leaching process is continuous on a year round basis. Run of mine ore (ROM) is placed on the heap beginning in mid April until late October. Overall gold recovery is projected to be 78% over a 325 day leaching cycle with annual production levels of 2.3 million tonnes of ore placed on the pad, with an average of 75,000 ounces of gold recovered per year. The recovery process utilizes conventional sodium cyanide leaching, carbon adsorption, high pressure stripping, thermal reactivation and acid washing, and on-site smelting.HISTORYFollowing a comprehensive governmental and public review of the proposed project, a Class A Yukon Water license was issued in August, 1995. Construction started in 1995 and leaching commenced in October 1996.A Socio-Economic Accord with the Tron Dek Hwech'in First Nations provides for employment, contract, and scholarship opportunities for First Nations citizens."

Jan 1, 1999

By Nikolas K. Sokol

Underground construction often requires working within a very congested urban environment, including excavating shafts adjacent to highly sensitive and multistoried structures, sometimes even within such structures. Shafts adjacent to heavily loaded column footings are often required due to space constraints. Invariably, footing surcharges must be considered during the design of shaft rock reinforcement. Rockwedge stability evaluation reveals that column surcharges can greatly impact the ability to meet the desired factor of safety. Design methodologies and examples to deal with these special circumstances are presented.

Jan 1, 2008

By Jean J. Abiassi

The Boston Marine Industrial Park (BMIP) VENT 6 project is a cut and cover tunnel, part of the Central Artery / Tunnel (CA/T) in the city of Boston. The BMIP job will serve as the south approach to the Third Harbor Tunnel crossing. The alignment is approximately 2500 Ft long and is made up of four sections starting from west to east: 1. West Tunnel 2. Boat Section 3. East Tunnel 4. Tunnel inside Vent 6 Cofferdam and connection to the Third Harbor Tunnel. The support of excavation (SOE) system for the West Tunnel, Boat Section, and East Tunnel are all a part of this project whereas the SOE for Tunnel inside the Vent 6 Cofferdam was a part of the contract for the Third Harbor Tunnel.

Jan 1, 1994

By Lenin Salazar Dulanto

La baja de precios en algunos minerales ha obiligado que las empresas mejoren su proceso productivo a través del uso de equipos de última tecnología en los procesos de mecánica, hidráulica, electricidad y electrónica, así como en la eficiencia en el corte y taladrado, extracción y transporte. Sin embargo, tanto el desatado y sostenimiento manual desarrollaron un estréss y desgaste de energía en el trabajador. En este sentido, el presente trabajo señala una nueva forma de realizar tales operaciones en el ciclo de minado de la empresa Milpo a fin de garantizar la seguridad física de los trabajadores y equipos.

Jul 31, 2003

By Yavuz Ali Topkaya

Rare earth ferrosilicide is a versatile alloy mainly used to control the detrimental effects of sulfur in steel and to modify graphite structures in cast iron. The aim of this study was to determine the optimum conditions to make rare earth ferrosilicon alloy using a preconcentrate produced from a bastnasite type of ore present in the Beylikahir-Eskisehir region of Turkey. This concentrate contained 23.5%REO, 41.37% CaF2, 10.69% BaSO4, 8.50% CaCO3, 4.18%Fe2O3, 2.83% Al2O3, 2.74% SiO2, 1.20% P2O5 and small amount of other oxides. The initial metallothermic reduction of this concentrate using ferrosilicon and aluminum in a graphite crucible placed in a muffle furnace gave very low recoveries due to the difficulties encountered in adjusting the slag composition, temperature and amount of additives. Therefore, two batches of rare earth oxide concentrate containing 61.1% and 81.7% cerium oxide, respectively, that were procured from a Turkish glass producer, were used to optimize with respect to temperature, duration, slag-making additives and amount of reducers. In these experiments, smelting and reduction was done in an induction furnace with graphite crucible, and, ferrosilicon and aluminum were added after melting the charge. As a result, there was no difficulty in obtaining a rare earth ferrosilicon alloy containing 35-55% RE, 5-25% Fe and 20-40% Si, with about 80% metal recovery. When the optimum conditions were applied to the preconcentrate, alloys of similar compositions were obtained with 70-80% recovery. Experiments were also done with mixtures of preconcentrate and rich concentrate, and, recoveries as high as 95% were obtained. Only in this case, to increase the recovery, mixtures had to be charged to the empty graphite crucible after heating the crucible to the required temperature.

Jan 1, 2006

By Val E. Payne

Issues between resource utilization and resource preservation often develop in connection with coal mining. One such conflict exists in eastern Utah where PacifiCorp and Energy West Mining Company are working with State and Federal agencies to address the resource recovery/resource preservation dispute. The effects of underground longwall coal mining on golden eagle (Aquila chrysaetos) cliff nesting sites have been studied at the Cottonwood Mine since 1986. Subsidence, escarpment spalling, and the nesting activities of the local eagle population were monitored.

Jan 1, 1986

By S. D. Cramer

Corrosion research is being conducted by the Federal Bureau of Mines to determine suitable construction materials for geothermal resource recovery plants. As part of this research, the corrosion resistance of 31 iron-nickel-, aluminum-, copper-, titanium-, and molybdenum-base alloys was characterized and evaluated in laboratory corrosion studies in low-and high-salinity geobrines representative of those found in the Imperial Valley, Calif. General, crevice, pitting, weld, and stress corrosion were measured at 105° and 232° C in deaerated brines and brines containing dissolved 02, C02, and CH4 General corrosion rates in deaerated brines at 105° and 232° C were usually below 5 mpy for the alloys tested except carbon steel, the low-alloy steels, Monel 400, 70-30 cupronickel, and the aluminum-base alloys. Dissolving carbon dioxide and methane in the brines at 2320 did not markedly alter these results. However, the introduction of oxygen, which can enter the brine during process operations, seriously degraded the corrosion resistance of many alloys by increasing the incidence of stress corrosion cracking, crevice corrosion and, except for the titanium-base alloys, pitting. In deaerated brine at 2320 C, the general corrosion rates for carbon steel and the low-alloy steels were relatively unaffected by pH in the range of 6.1 to 3.0. However, general corrosion rates increased sharply below pH 3.0. In deaerated brine at 232° C, welds in several iron-, nickel-, and titanium-base alloys corroded at rates comparable to the general corrosion rates of the alloys, but the addition of oxygen to the brine increased corrosion rates for welds in Inconel 625 and E-Brite 26-1. Alloys exhibiting good corrosion resistance in the deaerated Salton Sea KGRA-type brine at 232° C were E-Brite 26-1, Inconel 625, Hastelloy S, Hastelloy G, Hastelloy C-276, TiCode-12, Ti-0.2Pd, Ti-2Ni, Ti-1.7W, and TZM. The alloys most resistant to corrosion in oxygenated Salton Sea KGRA-type brine at 232° C were the titanium-base alloys. These alloys appear the most suitable for use in the construction of geothermal resource recovery plants. Carbon steel and the low-alloy steels are unsatisfactory for high-temperature, high-salinity brines and alternative low-cost materials with improved corrosion resistance should be sought.

Jan 1, 1980

By Michael V. Mergentime, Prakash M. Donde

The Nutley Quarry Trunk Sewer Project is a good example of a tunnel that went through difficult and complex ground. The 2 m (7ft.) diameter and 840 m (2,750 ft.)long tunnel passed through soft ground, mixed face, and hard sandstone. The soft ground and mixed face tunneling provided several challenges. During excavation of the tunnel, the Contractor encountered a number of unanticipated large boulders. In addition, the length of the mixed face portion of the tunnel increased by 100%. The Contractor tried various construction techniques to overcome the difficult ground conditions and complete the project. The tunneling progress was slower than expected. The Contractor claimed extra costs for differing site conditions. Through discussions and negotiations between the Contractor, Engineer, and Owner, all of the changed condition claims were settled before the construction of the project was completed. This paper addresses the difficult ground conditions, claims evaluation, and how they were resolved by cooperative efforts between the Contractor and the Owner/Engineer.

Jan 1, 2001

By T. A. Raczek

Materials for stronger ventilation tubing for underground use in hardrock mines were developed. The new material composites were evaluated in performance characteristics and compared to currently used materials. The materials were compared on tear, tensile, puncture and flammability properties. Based on cost versus performance data, a polyester film bonded to a polyester fabric was selected as the candidate material for field testing. Ventilation tubing fabricated from the selected material was field tested in two underground uranium mines for four-month periods. The test results indicated that the new composite showed an increase in useful life in the majority of applications, However, the cost performance ratio was not significantly improved to warrant commercialization of the product. When connected directly to some blowers, the material in close proximity to the blower deteriorated. However, material which was punctured or torn by mechanical means did not have further propagation of the tear. The high tear strength of the material prevented further damage. Improved methods of repairing inflated ventilation tubing were investigated and developed. All the repair methods were portable and self-contained. Repair kits based on adhesives, pressure sensitive tapes, and mechanical means were evaluated. Plier staplers and patch systems based on pressure sensitive adhesive proved to be most functional.

Jan 1, 1980

By James W. Reil, Douglas A. Anderson

Blast vibration monitoring has generally been regarded as a necessary evil. New instrumentation and computer programs can change this. Rather than the usual trial and error methods to control vibration problems, an integrated, intelligent approach is possible. There is also the possibility of diagnosing problems with the blast vibrations.

Jan 1, 1989

By A. S. W. Kurny, M. Z. Huq

Bangladesh ilmenite is partially altered, containing pseudorutile, rutile and haematite as well as the predominant ilmenite phase. A typical analysis is 39.45% TiO2, 24.19% FeO and 33.0% Fe2O3. Reduction of the ilmenite by charcoal was found to involve two major reactions: conversion of pseudorutile into ilmenite and rutile, and change of ilmenite into metallic iron and rutile. The first, which was much the faster reaction, was responsible for an initial increase in ilmenite content with reduction time at lower temperatures. Apart from these two major reactions, rutile was reduced to lower oxides at 1 100 degrees C with a consequent decrease in its XRD peak height

Jun 19, 1905

The effect of composition on electrical conductivity (resistivity), viscosity and liquidus temperature of the slags encountered in electric smelting of PGM-containing suphide concentrates is reviewed along with the relationsip between slag composition, slag-matte separation and metal losses to slag. Optimization of slag composition at furnace temperature is attempted on the basis of opposite and parabolic trends of the viscosity-conductivity relationships of the slags. The importance of surface tension of slags is emphasized using available and estimated information, which are grouped into a useful correlation. These values are coupled with or incorporated into slag viscosity plots to illustrate the correlation between the two factors which influence slag-matte separation as well as refractory attack. The electrode in the slag-resistance furnace is the central factor in the design and operation of the furnace by its role of conveying the smelting power. The obvious parameters are the size and positioning in the slag bath, which are defined by slag resistivity, furnace resistance, cell constant and power input. The flow of heat generated by the electrode current determines the energy distribution and furnace dimensions creating viscosity profiles, which in turn affect flow conditions. Thus the flow of slag and matte isdiscussed in conjunction with the furnace geometry, stirring action of the electrodes, buoyancy and electromagnetic effects. The action of the electric furnace as a settler is discussed. The rectangular furnace is considered as a channel reactor in this analysis and the action of the electrodes is described to indicate a balanced settling rate in the area of electrode action. Discussion of the design and production capacity of the electric furnace with reference to operating current, power input, furnace dimensions and electrode size are based on considerations derived mainly from slag properties such as its resistivity, viscosity and liquidus temperature.

Jan 1, 2004

By John Brown

Let’s talk about things that you, the driIl boss, the pit boss and the driller can do to eliminate the trend in drilling related accidents that have come to plague our industry in recent years. My paper will focus on reaI issues, problems and solutions that will affect our everyday outlook and attitudes about our jobs and lives. There are some real hard facts we must address if we are going to reverse this terrible killing trend.

Jan 1, 2000

By Zhu Tonghao

A method of calculating anti-slide pile, sheet pile, underground diaphragm and structure with anchors etc. is proposeed in the paper. The effect of the various layers of soil, anchors and bracings etc. on laterally loaded structures may be considered in the model. In the analysis the structure is divided into a series of elements. The transfer matrices of both deformation and internal force are established for each element. According to continuous condition neighbouring element should be connected. Thus the deformation and internal force of each element can be found out in conbination with boundary conditions. The method has a wider adaptability and it can be applicable to a great variety of the analysis of interaction between various structure and soil. If parameters in model are selected properly, the computed results would be in good agreement with the measured data.

Jan 1, 1991

By K. Ananthanarayanan, R. I. L. Guthrie, S. A. Argyropoulos

"The low cost and availability of micro-computers and their peripherals provides the metallurgical engineer with the opportunity to use such computers in a wide variety of applications. In this paper, the authors describe the development of a low cost data acquisition system capable of measuring up to 8 analogue channels at a sampling rate of up to 5000 measure mentsper second. This system is equipped with proper hardware and software so that the micro-computer can be linked to a central computer facility such as the McGill System for Interactive Computing (MUSIC). This central computer facility is supported by an AMDAHL V7 computer. Using the present interface, communication rates between the microcomputer and the central computing facility can be as high as 9600 (baud).The above mentioned data acquisition system is currently used for monitoring dissolution kinetics of ferro-alloy additions in liquid steel. In addition to this, special software has been developed which enables the user of this system to monitor solidification rates of ingots, etc. As economic considerations are always important, comparisons have been made with existing recorders which show that the cost Of the present system is only 30 per cent more than a two-pen strip chart recorder.RESUMELa disponibilité et le bas prix des micro-ordinateurs et de leurs périphériques permet à l'ingénieur métallurgiste d'utiliser de tels ordinateurs pour diverses applications. Dans ce rapport, les auteurs décrivent le développement d'un système d bas prix pour l'acquisition des données, capable de mesurer jusqu'à huit canaux analogues jusqu’à une vitesse de 5000 mesures par seconde. Ce système est équipe avec son propre ""hardware"" et ""Software"" qui relient le micro-ordinateur d’un ordinateur central, comme le système de McGill pour computations réciproques (MUSIC). Ce central d'ordinateurs est soutenu par l'ordinateur AMDAHL V7. Utilisant cet "" interface"", la vitesse de communication entre Ie micro-ordinateur et l'ordinateur central peut atteindre jusqu'd 9600 (baud)."

Jan 1, 1980