Search Documents

By P. -É. Boileau, M. Smets, T. Eger, J. Boutin

Long-haul dump (LHD) vehicles used in underground mining are known to expose workers to important levels of whole-body vibration1. These vehicles are generally designed without suspension and may be categorized as small or large LHDs depending on whether their respective load capacities are lower or larger than 3.5 cubic yards. While the majority of older vehicles are equipped with a rigid or unsuspended seat, more recent LHDs often incorporate a suspension seat. The objective of this study was to define the vibration spectral characteristics of most commonly encountered large and small LHD vehicles operating in mining operations. This was done in an effort to categorize the vehicles in terms of vibration spectral classes to be reproduced on a laboratory whole-body vibration simulator to assess the vibration attenuation performance of a typical LHD suspension seat. Methods Vertical vibration measured at the seat attachment point of 8 small and 8 large LHD vehicles operating underground in typical mining operations under loaded and unloaded conditions was considered as the basis for defining the spectral classes. By regrouping the data collected for each LHD vehicle size and load condition, the overall distribution of acceleration power spectral density (PSD) of measured floor vibration was determined over the 0.5 to 20 Hz frequency range. Mean and envelopes of maximum and minimum values of PSD spectra were computed to define the spectral classes, along with the corresponding values of frequency weighted rms acceleration determined in accordance to the ISO 2631-1 standard2. These spectra were further used to calculate the displacements needed to drive a whole-body vibration simulator consisting of a platform supported by two servo-hydraulic actuators having a total stroke of ±100 mm. For validation purposes, the vibration acceleration spectra measured on the simulator were compared with the target spectra representing the spectral classes. Finally, the vibration transmissibility characteristics of a typical suspension seat were determined under sine sweep excitation using both a rigid mass load and a human subject having a mass of 62 kg and 85 kg, respectively. The SEAT value, representing the ratio of seat to base frequency-weighted rms acceleration, was further measured under each of the defined LHD vibration spectral classes by loading the seat with an 85 kg subject. Tests were repeated three times and the mean SEAT values were determined to assess the seat’s ability to reduce exposure to whole-body vibration in LHD vehicles. Results Three spectral classes applicable to both loaded and unloaded conditions were defined as shown in Figure 1: one for large and two for small LHDs. The influence of load on frequency-weighted rms acceleration was found to be negligible for large and Class I small LHDs, while a shift of the peak acceleration PSD to lower frequencies was noted for the loaded vehicles. The influence of load was found to be more important for Class II small LHDs. Table 1 provides a

Jan 6, 2006

By D. Mohapatra

Extraction of Al(III) from aqueous sulfuric acid solutions into organic Cyanex 272®-carbon tetrachloride systems was investigated from a multi-component mixture containing aluminum, cobalt and nickel. Al(III) extraction efficiency was quantitative with 1.0 M Cyanex 272® in two stages at an aqueous: organic (A:O) phase ratio of 1:1 and an equilibrium pH of 3.2. The stripping of Al(III) from the loaded organic (LO) with different acids indicated sulfuric acid to be the best stripping agent. More than 99% stripping of Al(III) from the LO was achieved using 2 M H2SO4 at an A:O phase ratio of 1:1 in a single stage. The stoichiometry of the extracted species of Al(III) was determined by the slope analysis method. The extraction reaction proceeded via the cation exchange mechanism and the extracted species was assumed to be AlA3?3HA, where HA refers to the dimeric and A the anionic form of the extractant, Cyanex 272®. The extraction of Al(III) was studied in the presence of various ions to ascertain the tolerance limit of individual ions.

Jan 1, 2008

By E de Villiers

Several methods exist by which the capacity of a dense media separation (DMS) plant can be improved: 1) Increase the feed rate in spite of efficiency 2) Replace with bigger equipment 3) Add whole new module 4) Replace total plant 5) Change over to four shift/ seven days per week roster 6) Replace with alternative process 7) Increase the availability and utilization Options 1 ? 6 have varying degrees of cost implications. The seventh option would seem to be the easiest. Normally it is also the function of the plant operating and maintenance team to maximize this. Usually higher operating and maintenance cost are associated with an increase in these parameters. A general principle that is applicable to plants and systems is that as the complexity increases, the total availability decreases. By simplifying the flow line it may be possible to reduce cost while at the same time increase the availability and utilization. The typical standard DMS flow line contains components that compensate for the variance in pump performance or for the inefficient recovery of ferrosilicon with additional equipment. Things have changed though: 1) Advanced electronic control and monitoring is possible 2) More efficient magnetic separators are available 3) New more user friendly densifiers are available ORIGINAL FLOW LINE In principle the process consists of four flow lines or streams 1) Ore flow ? the feed is divided into a waste and product stream by means of the separating vessel

Jan 1, 2006

By K. Drescher

Excavations in deep level hard rock mines show rheological or time-dependent deformation responses to mining-induced stresses. These are generally not as dramatic as those seen in soft rock environments, such as potash and salt mines, but these deformations can nevertheless become substantial in time. It is usual to see total excavation closure at a much earlier stage than predicted by numerical models, and real-time measurements underground have confirmed that closure takes place on a more-or-less continuous basis, with highest closure rates observed after a blast and then slowly diminishing with passing time. This paper describes laboratory tests to determine the time-dependent response of hard rocks to loading, the results of the tests, and then quantifies these effects to explain the time-dependent phenomena observed underground. The primary intention of this work is to help explain the various time-dependent deformation processes around typical deep level hard rock tabular excavations. Three mechanisms were investigated in two typical hard rock types present in the deep level gold mines in South Africa, namely Ventersdorp Lava and Elsburg Quartzite. Uniaxial compression creep studies were done as the first part of the study followed by shear creep studies on discontinuities where crushed lava and crushed quartzite as well as a natural gouge were used as infilling. The last part of the study consisted of triaxial post-failure relaxation tests. The compression creep tests and the triaxial post-failure relaxation tests showed that the amount of energy dissipated by the lava is significantly less than for quartzite. For mines operating at depths greater than 2000 m the implication is that the lava must show a greater rockburst-proneness than the quartzite. Since the lava shows a lower post-failure stress relaxation, it can store sufficient energy for multiple rockbursts, which is seen in the clustering of multiple seismic events in the deep level mines. This study provides the first data available for energy change calculations in fractured rock masses, and provides the first general indications for rockburst intensities ahead of active mining faces.

Jan 1, 2003

By Philip W. Holland

This Bureau of Mines report discusses the results of three independent reconnaissance geochemical surveys conducted in the vicinity of the Bush Dome reservoir in the Bureau-owned Cliffside field near Amarillo, Tex. The surveys consisted of (1) determining the helium content of area ground waters, (2) determining the helium content of area soil gases and ground waters, and (3) determining the helium content of soil gases collected on a grid sampling pat- tern in the Cliffside field area. The native natural gas in the Cliffside field contains about 1.8 percent helium. To date, approximately 54 billion cubic feet of gas containing approximately 39 billion cubic feet of helium has been injected into the center of the Bush Dome structure. The research work, which was completed under contracts, was done to determine if helium concentration levels in ground water and soil gas could he used as an indication of the presence of helium in a subsurface natural gas accumulation. Results of the surveys were positive in that helium-in-water and helium-in- soil-gas anomalies were detected in portions of the Cliffside field area. All helium analyses were performed by mass spectrometric techniques.

Jan 1, 1979

By H. L. Riley

Cleaning and handling of fine coal are generally conceded to be more difficult problems than preparation of the coarser sizes. Increased mechanization in the coal-mining industry has, in general, resulted in an increased percentage of the fine sizes in the total coal mined. If the coal fines are cleaned by wet methods, the minus-1/16-inch square-mesh particles cause most of the sludge and slurry problems encountered in preparing wet coal. Equipment that separates coal from refuse on the basis of specific gravity is not efficient on sizes that, because of their fineness, do not follow the same laws of hindered settling as the larger particles. Probably the best solution of fine-coal cleaning problems is to use other methods, such as flotation, that utilize other physical characteristics than those determining hindered-settling ratios. Regarding the type of flotation known as the Elmore vacuum-flotation process there has been a scarcity of data and information available in this country. An investigation has therefore been made to obtain additional date and information on this process under laboratory conditions. During this investigation an effort has been made to evaluate the relative efficiencies of vacuum and mechanical laboratory froth flotation cells. The investigation included float-and-sink, screen-sizing, and flotation tests on 2 different samples of 14-mesh to 0 raw coal and an a sample of slurry from the settling-tank overflow of a typical washer. One raw-coal sample was obtained from the American bed and represented a type of coal that is relatively easy to clean. The other raw-coal sample was from the Mary lee bed and represented a type considered difficult to clean.

Jan 1, 1954

By J. Hop, A. Støre, T. Foosnæs

The carbon cathode for aluminium electrolysis is also part of the container of the process. In order to understand the behaviour and possible failure of the cathode, detailed material properties under operating conditions are needed. The paper reports experimental studies of bath and sodium in filtration, graphitization with time, loss of strength due to sodium, sodium expansion as function of pressure, as well as creep due to the developed stresses. As an example, sodium and thermal expansion data are used to calculate strain-stress models of realistic cell designs, and possible design weakness can be pointed out. Keywords: carbon, cathodes, sodium expansion, strength, graphitization, creep

Jan 1, 2004

By W J Fisher

Northern Australia leads in world-class mineral deposits' is a bold statement. First there must be a starting point. Land north of the Tropic of Capricorn (23¦ 26' 5") will be regarded as Northern Australia covering nearly 40 per cent of the land surface of Australia. As opposed to land south of the Tropic of Capricorn, it should be regarded as Tropical Northern Australia and for the sake of brevity, (TNA) Refer Figure 1. Apart from the tyranny of distance from centres of power and population in the temperate zone, it suffered in the past from the belief that the tropics are unsuited for European workers and from the lack of infrastructure. Outstanding mineral deposits of iron, base metals, gold and diamonds, discovered and developed in the past three decades, provided the substance for the title. There are many world-class mines producing and there are mineral deposits neutralised through Government policy. TNA can maintain its lead in world-class mineral deposits provided Government policy will stop partitioning the land and decreasing that available for exploration. Let's look at what we have that is world-class. In Western TNA iron ore deposits at Paraburdoo, Mt Tom Price, Marandoo, gold at Telfer, diamonds at Argyle. In central TNA uranium at Ranger and Jabiluka, lead-zinc-silver at McArthur River, gold at the Tanami, manganese at Groote Eylandt and bauxite at Gove. In eastern TNA Mt Isa, Hilton, Century zinc-lead, bauxite at Weipa, gold at Kidston, Mt Leyshon, magnesite at Yamba and coal mines in the Bowen Basin. Those mines or deposits stand out yet are only an indication of the numerous lesser mines and of mineral deposits depending for development on market demand and/or changes in Government policy, eg 'The Three Mines' policy. Very large areas of mineral rich structures in the western, central and eastern parts of TNA are concealed below flat lying comparatively young unmineralised sediments. The Great Artisan basin sediments in eastern TNA can and do host oil shale and non metallic minerals. Nearly 40 per cent of western TNA is covered by the Great Sandy Desert. The Canning Track, with a series of 54 wells, was constructed by surveyor Alfred Canning in 1908 - 1910 with great difficulty. It extends 1700 kilometres from Halls Creek in the north to the gold town of Wiluna in the south, through the Great and Little Sandy Deserts. Gold explorers are following favourable structures extending to the north east below the sediments and sand hills covering the track. Half of central TNA's mineral structures are concealed by the Tanami desert and the Cretaceous sediments covering the pastoral regions of the Barkly Tableland and the Daly Waters to Top Springs pastoral areas. The Georgina Basin in the south eastern section is part of the concealment.

Jan 1, 1994

By Y. Wang, S. Sridhar, B. Coletti, G. N. Shannon, S. Vantilt

The final removal of inclusions in the ladle, tundish, and mold in a continuous casting process involves the kinetic steps of liquid film drainage, interface rupture, and absorption of the inclusion into the overlaying molten slag. During this process, oxide inclusions can undergo chemical reactions with the slag. This paper presents recent results on imaging the slag/steel interface and elucidates the evolution of Al2O3and Al2O3-CaO inclusions during their separation from the steel and on their incorporation into the slag. Experimental results, obtained through a Confocal Scanning Laser Microscope, are compared with thermodynamic predictions.

Jan 1, 2004

The Martha Hill project operates with a nett surplus of water, due to the catchment of rainwater on the tailings dam and the requirement to de-water the open pit mine. It is necessary to discharge this surplus, treated as required, to the Ohinemuri River which flows past the process plant.   The treatment plant, adjacent to the process plant, handles all effluent from the Martha Hill operation including water pumped from the mine, excess water from the tailings decant, and seepage from the tailings dam underdrains. To-date the plant has treated and discharged over 800 000 tonnes of water.

Jan 1, 1991

This report presents the results of studies of Kennecott Copper Corporation's tailings embankment at Magna, Utah. The stability studies described were performed on only one cross section of the embankment, utilizing; data obtained from drilling, sampling, and testing, which was limited in nature. The main objective of the data collection was to provide background information to support the overall research effort. Because of this limited scope, it is not possible to evaluate the degree of safety or adequacy of the embankment or disposal system, and the information and data contained in the body of this report must be judged in that light. The first part of this report contains discussion of site geology and seismicity, pertinent information on the refuge disposal system, a discussion of the tailings materials characteristics, a summary of the engineering analyses, and A bibliography. The second tart (appendices) contains basic geologic and engineering data supporting the discussions in the first part of the report.

Jan 1, 1974

By David A. Staab

Numerical modeling was used to investigate the feasibility of using two geophysical imaging techniques, cross-borehole ground penetrating radar (XBGPR) tomography and electrical resistivity (ER) tomography, for detecting and characterizing defects in deep-mixed soil columns. XBGPR modeling was accomplished with a three-dimensional numerical forward modeling code and a two-dimensional inversion routine. Spatial variations in apparent dielectric constant (Ka) and attenuation (a) were mapped. Electrical resistivity modeling was accomplished with a three-dimensional numerical forward modeling code and a three-dimensional inversion routine. Spatial changes in electrical resistivity were then mapped. Three different types of defects were simulated, in addition to a defect-free column. The computer simulations suggest that XBGPR tomography and ER tomography might be useful, non-destructive methods for detecting and estimating the extent of defects in deep-mixed soil columns. The results show that small, isolated defects might be difficult to detect, but defects approximately equal to or larger than the sampling interval (for XBGPR) or vertical electrode spacing (for ERT) should be detectable.

Jan 1, 2004

By Mohan K. Wali

This report, the first in a series of 13 reports, provides a summary of 11 major topics on which individual reports have been prepared. These major topics are: (a) Nature of coal mine spoils, topsoils, and unmined soils; (b) influence of macro- and microclimate on (c) plant production on spoils and topsoils; (d) prediction of aboveground biomass from plant cover; (c) mineral composition of plants; (f) controlled environment studies on plant growth response; (g) microbial communities (h) water chemistry and organism diversity of catchbasins; (i) vegetation and soil development on abandoned, and (j) topsoiled sites; and (k) viability and diversity of seed bank. Based on these investigations, general conclusions and some recommendations are presented.

Jan 1, 1982

By Stig Eriksson

In Switzerland two major railway systems as shown below in Figure 1 has recently been completed or is under construction: ¦Lötschberg, south of Bern which was commissioned in 2007 ¦Gotthard, south of Zurich which is scheduled to be commissioned in 2016The aim is to increase the transport capacity of the railway system and to transfer more transport of goods to the railway by offering transport of trailers and lorries on the new railway systems. It will have a positive environmental impact but also improve the congested traffic situation of the highways in north-south directionThe Gotthard tunnel is totally 57 km (35 mile) long and the Lötschberg tunnel is 35 km (22 mile) long. Both tunnel systems consist of two parallel single track tunnels connected with cross tunnels at every 333 m (1 093 ft). Additionally there are cross-over tunnels and caverns for installations and operation. In the Lötschberg tunnel, the majority of the excavation has been by Drill & Blast and in Gotthard tunnel the major part is being excavated by TBM.

By P J. Fourie, J R. Walklate

Gravity separation techniques have been in use in the mineral sands industry for decades; from the Reichert cone to Wilfley tables, Wright sluices and the Kelsey Jig, all attempting that elusive perfect gravity separation. Just as the gravity separation industry evolved, Richards Bay Minerals also evolved in their use and approach to gravity separation. This paper discusses the history of gravity separation at Richards Bay Minerals and briefly comments on future developments. History Primary Concentration Richards Bay Mineral?s (RBM) first mining concentrator and mineral separation plant commenced operation in 1977 to process ilmenite, rutile and zircon bearing dunal deposits along the northern Natal coast. The orebody contained a greater proportion of non-valuable magnetic heavy mineral in the SG range of 3 to 4 compared to West Australian and Florida USA deposits, making mineral separation more difficult(1). The deposit was mined using two dredges feeding a floating 2000 tph concentrator. Concentrator feed was screened and fed to two four-stage circuits consisting of primary, scavenger, cleaner and recleaner Reichert cones [see Figure 1]. The primary units were fed at a rate of 80 tph and a density of 60% solids by weight.

Jan 1, 2006

By Collin Stewart

Bowie Resources, LLC (Bowie) has been using the Stability Mapping System (SMS) developed by Dr. Keith Heasley, West Virginia University, since 2005. Seven three-entry longwall gateroads, four longwall panels and a five-entry set of mains have been mined in two different seams in areas originally analyzed with the SMS. This paper compares predictions of mining conditions based on the SMS with actual mining conditions. Specific comparisons include longwall and continuous miner (CM) productivity, longwall tailgate response and support and CM roof bolting requirements. The paper also discusses current thoughts at Bowie on the use of different weighting factors for CM development, longwall face conditions and longwall tailgate support requirements.

Jan 1, 2007

By Jérôme Boutin, Rémy Oddo, Sylvain Ouellette, Paul-Émile Boileau, Gilles LeBlanc, Pierre Marcotte

ackleg rock drills are widely used in the mining industry and are known to generate high levels of hand-arm vibration which contribute to the development of the hand-arm vibration syndrome for exposed miners.1-3 To reduce the vibration levels, a prototype of an antivibration handle was developed as part of a previous study.4 To provide some bench marking for this handle prototype and to follow the evolution of its performance over time, a test bench was developed to characterize the vibration emission values of jackleg drills under controlled operating conditions. As the current ISO 8662 series of standards could not apply directly to this type of tool, there was a need to design and validate a test bench to evaluate the vibration emission values of jackleg drills, while taking into account the conditions specific to the operation of this type of tool. Methods A test bench including an energy absorber, was developed for testing jackleg drills based on the ISO 8662-3 standard 5. The energy absorber was bolted to a 3300 kg concrete block to ensure tool stability. A pictorial view of the device is given in Figure 1. For validation purposes, acceleration measurements at the handle of a conventional jackleg drill were taken simultaneously along the three axes (xh, yh and zh) in an underground rock drilling operation as well as on the test bench. The handle accelerations were measured for three different jackleg angles (13º, 28º and 43º) determined with respect to the floor. Moreover, each measurement was repeated at least three times to asses the data repeatability. [ ] Results As a preliminary validation of the test bench, Figure 2 provides a comparison of the frequency weighted rms acceleration spectrum measured along the zh-axis, for both underground drilling and operation on the test bench (28º jackleg angle in both cases). It is shown that the vibration measured on the handle of a jackleg drill operating on the test bench is representative of that recorded during typical rock drilling operations, despite the fact that some harmonics of the percussion frequencies are generated with a higher amplitude on the test bench. Table 1 provides

Jan 6, 2006

By B. J. Sauer

Variable frequency drives (VFD’s), or adjustable frequency controls (AFC’s) as they are more precisely identified, have been available to the mining industry for over 20 years. However, in recent years as the push to cut production costs has become ever so crucial, AFC usage has become more widespread. This paper seeks to provide professionals in mineral processing plant design and operation with an introduction to AFC’s, insight as to why AFC control for AC induction motors can be advantageous, and specification and design considerations.

Jan 1, 2002

A regular general meeting of the Canadian Mining Institute will be held in Vancouver, B. C., on Nov. 26-28. The Council extends a cordial invitation to all members of the American Institute of Mining and Metallurgical Engineers to attend.

Jan 11, 1919

By Chris Sammon

The Block 75 portion of the City Creek redevelopment project in Salt Lake City required multiple shoring walls surrounding the 6 acre site constructed to depths ranging from sixty-five to ninety feet below original street grade. Shoring for the project was challenging due to site soils consisting of cobbles, sands and gravels, interlayered lakebed silty clay and fine sandy silt with incised stream deposits of silty/clayey sand and gravels combined with a high groundwater table. Moreover, several abutting structures each with a unique foundation system would be directly or indirectly supported by the shoring system. Three sections of interest are the shoring walls constructed at Main Street, Deseret Trust Building and Eagle Gate Tower. Main Street shoring extended to as much as sixty-five feet below street grade and utilized existing basement walls anchored in place in the upper zones with soil nail walls with pre-installed vertical elements for face stabilization below. Data are presented which illustrates the effect dewatering had on the settlement of the Main Street Shoring. The Deseret Trust Tower shoring supported a 12 story, historical masonry building. Site conditions dictated a separate design for the east side and the north side of the building allowing comparison of relative performance between these walls. Settlements of this structure were controlled by installing micropiles through the 90 year old structures spread footings. Shoring for the Eagle Gate Tower was to be constructed immediately adjacent to a mat supported 22 story high rise structure. This shoring system combined secant piles, ground anchors and incorporated existing abandoned-in-place pipe piles with infilling high pressure jet grouting to create a cutoff wall and eliminate the adverse impacts of dewatering below this sensitive foundation.

Jan 1, 2010