Search Documents

By J. F. Breedis

The stabilization of austenite in Fe-Ni alloys against martensitic transformation after reversion has been attributed' to the lattice imperfections remaining from previous transformation. More recently, however, such stabilization has been associatedzy3 with compositional changes which occur in martensite during slow heating. Dislocation arrangements in deformed austenitic stainless steels strongly influence transformation to martensite on quenching.4 Therefore, it is of interest to observe the transformation behavior of stainless steel after reversion, especially since previous studies have been confined to Fe-Ni alloys. The transformation-product morphology also differs in the two iron-alloy systems;6 plate martensite forms in the latter while stainless steel transforms to lath-type martensite. Samples of Fe-16 wt pct Cr-12 wt pct Ni (maximum C + N = 0.005 wt pct, 0 = 0.02 wt pct), prepared by vacuum melting and casting from high-purity components, were annealed at 900°C for 24 hr, after cold rolling to produce a 40-p grain diameter. The M, temperature of this alloy is -80°C and samples are fully austenitic after annealing. The amount of martensite present after quenching, annealing, and requenching was determined magnetically, to within 0.01 wt pct, using a vibrating specimen magnetometer. Nearly 14 pct of martensite forms during the initial quench in 1 min at -196°C. Two-min and 2-hr anneals were done in air and in evacuated quartz capsules, respectively. All specimens were electro-polished before making the magnetic measurements.

Jan 1, 1967

By Charles C. Dahl, Gordon C. Presley, Andrew E. Nevin, Bruce A. Kennedy

How does SME-AIME cope with profound changes in technology, markets - and most importantly - in employment patterns facing its membership today? This is the question that prompted the Society's Board of Directors to appoint a Long-Range Planning Commission (LRPC) (see ME, Feb. 1984, pp. 118 and 128). This is also the question addressed most particularly by the LRPC's Scope Committee. The Committee started its deliberations by asking such basic questions as "Who are we?" and "What is our business?" The Scope Committee then reviewed the findings and recommendations of other more specialized committees to develop and integrate their concepts of the Society's business for the next 10 years. The policy-making suggestions of the LRPC were reviewed and acted upon by the Board of Directors at its open meeting in Los Angeles on Feb. 26, 1984. At the Oct. 23-26, 1984 SME Fall Meeting in Denver, the Board will again review LRPC recommendations. In answer to the question "Who are we?" the Scope Committee proposed description, which was accepted by vote of the board of directors: . . A technical and professional organization that consists of individual members, namely those mining engineers, metallurgists, geologists, earth scientists, economists, managers, educators, and other professionals concerned with all facets of exploration, production, distribution, and using of mineral commodities. "These mineral commodities include all metals; industrial minerals, including construction materials and fertilizers; coal, oil shales, tar sands, and other mined fuels. Among the earth's mineral resources, only wellpumped oil and gas lie outside the Society's specific purview. "Traditionally, SME members work in the fields of engineering, technology, exploration and discovery, development, construction, mining, quarrying, beneficiation and processing, handling and transport, equipment manufacturing, sales and marketing, data processing, safety, land reclamation, environmental protection, taxation, administration, and management of these elements. "Members practice their professions in industry, in universities and research institutions, and in government. They may be operators, manufacturers, sales persons, contractors, consultants, analysts, researchers, educators, advisors, regulators, or members of supporting staffs. "The members of the Society are leaders in dedication to their crafts, in innovation, and in the pursuit of excellence. Among their numbers they count the most distinguished of engineers, applied scientists, and managers. "The Society is based in the United States, is active on a worldwide basis, and is open to nationals of any country. Certain qualifications must be met for attaining and maintaining membership." Purpose of the Society As to the question "What is our business?" the Scope Committee restated our purpose in light of current practice and the constitution of AIME and the bylaws of AIME and SME. The Board of Directors accepted the following proposed purpose of SME: "To further the professional development and well-being of its members by publishing and distributing technical writings, news, and information; by sponsoring meetings of members; by providing forums for discussions and for continuing education; and by fostering communication on the subjects within its purview. "The Society assists educa-

Jan 4, 1984

Water Balancing in Mineral Processing - Issues and Opportunities

Sep 13, 2010

By J. Mitchell Linne

In 1985, at the request of Bureau of Land Management, the U.S. Bureau of Mines studied a 54,480-acre portion of the 93,205-acre Dry Valley Rim Wilderness Study Area (CA-020-615), in order to evaluate its identified resources. The area studied is in Washoe County, NV, and Lassen County, CA, about 35 miles east of Susanville, CA. No metallic resources were identified. The Red Rock and Willow Springs areas contain 85 million tons of altered basalt with zeolite amygdules. This material, averaging more than 50 percent chabazite, constitutes a subeconomic zeolite resource. This zeolite-bearing material would require beneficiation to upgrade it for higher value uses. Natural zeolites have a small market in the United States, which is presently supplied by other higher grade material. There is low probability that these resources will be mined in the foreseeable future. The Capricorn claims, adjacent to the study area, are on alluvial sediments containing more than 30 percent montmorillonoid clays. The material is not usable as pozzolan and was not tested for other uses such as absorbency, oil clarification, or insecticide carrier. The term pozzolan refers to a number of siliceous materials which are combined with portland cement to enhance the physical properties of the resultant concrete. The area is remote from market and contains low value material. It is improbable that this occurrence will be mined in the foreseeable future.

Jan 1, 1987

By P. Hickey, J. Spenceley, T. J. DeMull

Development of the Batu Hijau Project was successfully completed in the fourth quarter of 1999 with the final handover and start-up of ore processing facilities. The development project had started more than three years earlier, in August 1996, when the Owner, PT. Newmont Nusa Tenggara (PTNNT), awarded an EPC contract to Fluor Daniel (FD) for design and construction of the project including: copper concentrator, port, power plant, town site, and infrastructure. PTNNT managed the development of the mine and procurement of mine equipment with its own forces. Bringing the Batu Hijau copper deposit into production was the largest mining project ever undertaken. Development of Batu Hijau was a complex project involving the work of tens of thousands of people in all parts of the world to complete engineering, manufacture and deliver equipment, supply materials, and build the plant. The ore deposit is located on the tropical island of Sumbawa in a remote and undeveloped section of Indonesia. The location and environment presented challenges for all phases and aspects of the project. To meet the challenges, the project team combined good planning and teamwork to best utilize the resources available. This approach assured continuity of personnel through construction to operations and minimized cost, resulting in completion of the project ahead of schedule and under budget.

Jan 1, 2001

Mining and the related extractive and processing industries are chiefly responsible for America's high standard of living. Enormous quantities of sand and gravel, limestone, copper, iron and a myriad of other mineral commodities are required to sustain our growing nation. However, the mineral deposits, both domestic and foreign, are becoming increasingly difficult to find. Adding substantially to the problem, is the fact that the conditions are worldwide. Foreign politics are increasingly affecting mineral commodity availability. Figure 1, taken from Bureau of Mines, "Status of the Mineral industries 1976" illustrates our dependency (in some cases total) on foreign sources for vital mineral commodities. While few nations are capable of exerting an OPEC-like influence on any one mineral commodity, the threat of cartel arrangements and related control strategies is evident. Nationalization of entire industries, once they become self-sufficient, is also exerting a disruptive influence on a large portion of the mineral industries.

Jan 1, 1977

By D. M. Loring

Radon progeny have been a health and safety concern for miners since the mining of radioactive minerals began. Through the ?nuclear age?, it has become better understood and the regulations have become more robust. Ventilation and control practices have improved, thus reducing miners? exposures. This paper provides an overview of radon in mining, the progress of the regulations, and discusses some of the uranium miner studies that contributed to the knowledge of the pathology of radon.

Jan 1, 2009

Council for 2003/2004 President T.R. Stacey President-elect F. M. G. Egerton Vice-presidents Senior W. H. van Niekerk Junior R.P.H. Willis Immediate Past-president S.J. Ramokgopa Honorary Treasurer J.A. Cruise

Jan 1, 2004

By Lisa A. McDonald

The environmental compliance process affects all aspects of hardrock-mining operations, from exploration through post-closure. The primary components of the environmental compliance process are requirements under the National Environmental Protection Act of 1969 (NEPA) and the permitting requirements associated with various other federal, state and local laws. This study considers the Greens Creek Mine and the development of two other projects (Alaska-Juneau & Kensington). These mines were used as the foundation for a case study of the impacts of the environmental compliance process on hardrock-mining activity in Southeast Alaska. The case study presents the institutional and legal requirements, followed by a discussion of the impact of this process on the production and timing of the three mines. The results of this preliminary study reveal some interesting findings, some expected and others unexpected, regarding the impact of the permitting process on the exploration, development and (proposed) operation of the three mining projects in the Juneau area. Determining the cost of compliance with these requirements is an important step in evaluating the appropriate course of action to protecting the environment while providing the necessary raw materials needed for society. This preliminary study highlights the initial starting point for such an analysis.

Jan 1, 1992

By M. E. Poad, M. M. McDonald, J. C. Johnson, W. G. Pariseau

A U.S. Bureau of Mines case study of pillar recovery in high-grade ore near the Ross shaft at the Homestake Mine, Lead, SD, has demonstrated the usefulness of the finite-element method for evaluating shaft pillar mining plans and shaft stability. This report focuses on mine measurements and calibration of the two-dimensional computer model and is the second in a series of three Reports of Investigations describing the Ross shaft study. In this study, borehole extensometers and other instruments were installed to provide data for model verification and to monitor the shaft. Results of the recalibrated two-dimensional model (UTAH2) confirmed the premining stability evaluation. However, after mining began, concern was expressed because cracks and other signs of ground motion appeared at considerable distances from the area of active pillar mining. In part 3 of the study, an intense three-dimensional modeling effort using UTAH3 was initiated. The results again showed that the observed effects were within expectations and that the shaft would remain safe. Three-dimensional analyses of alternative pillar mining scenarios indicated that more of the shaft pillar ore reserve could be recovered than previously thought.

Jan 1, 1995

By George T. Faust

The petrographer engaged in examining the products resulting from the beneficiation of ores, and rock minerals is constantly required to develop new means acid methods of assaying microscopically the results of such operations. From time to time investigators have published descriptions of apparatus that have aided in solving problems in processes of physical separation. Thus, in 1919, Coghill and Bonardi 3/ published a paper covering the application of the binocular microscope and camera lucida to the microscopic analysis of pulverized ores. Similar work has been published by Schneiderhohn 4/ Schwartz 5/, and Head and his associates 6/, 7/, 8/. The present paper goes further and considers application of the polarizing comparison-microscope to problems directly concerned with mineral dressing where it is desirable to compare analogous products, and in addition it suggests new uses in various related fields. This work was conducted under the cooperative agreements of the Southern Experiment Station of the Federal Bureau of Mines and the University of Alabama.

Jan 1, 1940

Objective: To identify and evaluate a permanent stopping to direct ventilation airflows in large-opening metal/nonmetal mines.

May 1, 2006

Based on X-ray phase analysis and exploratory experiments, a new technology was developed to recycle multiple valuable elements in spent Al2O3-based catalyst. The experimental results showed that after roasting at 750°C for 30 minutes at an Na2O:Al2O3 mol ratio of 1.2, the leaching recoveries of alumina, vanadium and molybdenum from the spent catalyst were 97.2%, 95.8% and 98.9%, respectively. Vanadium and molybdenum in sodium aluminate solution can be recovered by barium hydroxide and barium aluminate. The precipitation recovery of vanadium and molybdenum was 94.8% and 92.6%, respectively. Al(OH)3 is prepared from sodium aluminate solution using the carbonation decomposition process. The purity of Al2O3 is 99.9% after calcinations, and the recovery of alumina can reach 90.6% in the whole process. The Ni-Co concentrate was leached with sulfuric acid, and a nickel recovery of 98.2% and a cobalt recovery of more than 98.5% were obtained under the experimental condition of 30% (w/w) H2SO4, 80°C, a liquid: solid ratio of 8:1 (by weight), a reaction time of 4 hours and a stirring rate of 800 rpm.

Jan 1, 2007

By Roger M. Turpening

This study was performed to examine the feasibility of using seismic shear waves to detect the presence of abandoned coal mines. !he Antiquity Coal Mine near Antiquity, Ohio was used as a region of known voids. No attempt was made here to accurately locate the mine tunnels if detection was obtained. The results of this study were positive. Sharp changes in the amplitude of the received shear waves were clear indications of the presence of a fluid (gas or liquid) filled region between the source and receivers. When moving the source showed no change in the received signals it was concluded that the voids existed beneath the sensors. Prior to these tests drilling (SM-3) had determined that a void did exist in this area. This void was confirmed by this shear wave test and two additional voids were found.

Jan 1, 2012

This report summarizes the results of several field tests conducted by Collins for the Bureau of Mines under contract S0122076 and contract H0232056. The field projects represent a part of Collins continuing effort on a broad study of coal mine communications. These experiments analyze the propagation characteristics of radio signals in a working coal mine environment. The intent of the program is to provide basic propagation loss characteristics by which we may evaluate various approaches to an integrated mine communications system. The goal of such a system is to satisfy both operational and emergency communications needs in the mine.

Jan 1, 1974

By Jan Van Greunen, Mark Vanderzee, David Haug, Geoffrey Hughes, Yiming Sun, Roozbeh Geraili Mikola

"The Sanitation Districts of Los Angeles County is planning to construct a new, approximately 7-mile-long (11.3 km) effluent outfall tunnel to be excavated by TBM and lined with precast concrete segments. Anticipated net operating pressures within the tunnel are expected to approach 3 bar. To counteract joint opening and exfiltration leakage, an approach has been investigated to post-tension the precast concrete tunnel lining with steel tendons. The tunnel alignment crosses several seismically active fault zones, at which installation of steel pipe is proposed as a secondary inner lining to mitigate potential offset displacements. This paper discusses the tunnel lining design approach and methods used to address these unique challenges.INTRODUCTION The Sanitation Districts of Los Angeles County (Sanitation Districts) is planning to construct a new 18-foot-diameter (5.5 m), approximately 7-mile-long (11.3 km) tunnel from the Joint Water Pollution Control Plant (JWPCP), located in the City of Carson, to the existing White Point outfall manifold structure at Royal Palms State Beach (RPSB) (Figure 1). The project is part of the Sanitation Districts’ Clearwater Program, which will improve overall system reliability through the repair and replacement of the existing aging infrastructure. The existing system includes two 6-mile-long (9.7 km) tunnels, 8- and 12-feet in diameter (2.4 and 3.7 m), and four ocean outfall pipes with a maximum capacity of approximately 675 million gal/day (MGD) (2.6 billion L/day). Addition of the new parallel tunnel will increase overall capacity to accommodate peak wet weather wastewater flows of up to 1,262 MGD (4.8 billion L/day) and will allow inspection and repair of the existing tunnels. The new outfall tunnel will be excavated using a pressurized face tunnel boring machine (TBM). Shafts at the north (JWPCP Shaft) and south (RPSB Shaft) ends of the proposed alignment will connect the tunnel to the existing wastewater treatment plant and existing ocean outfalls manifold and during construction act as launch and receiving shafts for the TBM. The tunnel will be excavated from north to south as a single heading."

Jan 1, 2016

By Gary A. Kingston

Rolled steel, steel forgings, and steel castings in the Pacific Northwest (Washington and Oregon) are produced principally in the Seattle, Wash., and Portland, Oreg., metropolitan areas. Steel-mill products are rolled from carbon and some alloy &eels by three companies into shapes such as reinforcing bar, rods, rounds, squares, flats, and hot-rolled strips; structural shapes, - such as angles, channels, and I-beams, also are rolled. Carbon and alloy steel ingots are poured and forged at a Seattle plant into ship shafting, drive shafts, billets, slabs, bars, rings, hooks, and other items. Static, shell, investment, and centrifugal castings are produced at 19 steel foundries in a wide range of steel specifications. All Pacific Northwest steel output is based on remelting steel scrap. Local iron ore might be used in the future to supplement steel scrap as a metal source. Ore reduction would probably be achieved by methods other than the blast furnace. Current melt-shop practice and problems are basically the same in Pacific Northwest steel plants as in cold-melt shops in other parts of the country. Quality steel production is receiving more emphasis in this region with the installation of modern analytical equipment and vacuum pouring and melting facilities.

Jan 1, 1962

By E. C. Hoeman, W. C. Stoecker, R. C. Redfield

"INTRODUCTION Industrial sands, characterized by specific physical and chemical proportion, are,essential new materials for the manufacture of glass, sodium siliante and other products. Sands of suitable characteristics are used extensively for molds and cores in the casting of metals as a granular medium in municipal water filters, as abrasives, as traction sand to prevent the slipping of driving wheels of self-propelled vehicles on trucks and in various ceramic and other structural forms. In addition to the use of common silicon sands in concrete, cement, and mortar, special sands find use in sand-lime brick oxychloride cement, and flooring, for coating prepared roofing, and for placing ware in saggers although sand for sandpaper has been mostly displaced by other harder mineral or synthetic grains, other abrasive uses are numerous and include sandblasting stone sawing, glass burnishing and finishing."

Oct 1, 1945

By Seppo Lähteenmäki, Pertti Koivistoinen, Jaakko Levanaho

"This paper describes the benefits and disadvantages of fully autogenous grinding when compared to grinding with steel grinding media. The study is a real case study based on a low tonnage, high grade mining project in a remote location in a developing country. The study compares the capital and operating costs of using either SAG mill, Ball mill, Crusher (SABC) or fully autogenous (AG) grinding circuits and produces an economical analysis of the project for both options. The economics have been developed for the overall project, including mining, processing, environmental and the infrastructure as well as for the additional cost of constructing a fully autogenous grinding circuit instead of the original plan of a SAG Mill, Ball Mill circuit.The paper also describes the development of the autogenous grinding circuit at Outokumpu Oy, Pyhäsalmi mine. This experience was used to design the autogenous grinding circuit for the case study. Pyhäsalmi Concentrator has over 30 years of experience in operating autogenous grinding circuits and therefore provides a sound base for the new circuit design.INTRODUCTIONGrinding of ore using steel grinding media is currently the most commonly used method in the mining industry. Autogenous grinding, ore replaces iron media, is also common especially in Europe and Africa. Iron ore industry in North America uses autogenous grinding in primary and/or secondary stages extensively. In gold, copper and other base metal industries, autogenous grinding is not as common, although there are operations where pebble grinding is or has been used in the secondary grinding stage. There are many variations of autogenous grinding in use in the mining industry. These variations include different mill sizes, mill length to diameter ratios, ore lump sizes, screening and pebble crushing configurations."

Jan 1, 2000

By PW Meisel

An hydraulic-powered reel system to minimize peak tension transients in shuttle car trailing cables has been theoretically designed and analyzed using a computer. A single spring-loaded take-up sheave stores or gives up cable to maintain tension within specified limits. Controls have been incorporated to shut down the vehicle before all cable is removed from the reel and to de-energize the cable in the event of a reel/cable jam. Full-scale hardware configuration drawings sufficient for manufacture of a test system have been completed.

Jan 1, 1983