Search Documents

By D. R. Dolinar

The fall of small pieces of rock between roof bolts causes over 80 pct of the ground fall injuries in underground coal mines. Roof screen, if installed on the bolting cycle, can significantly reduce the number of these injuries. As the surface of the roof fails, the screen will have to retain the broken rock without failing or excessive deformation. Welded wire screen is the most common type of screen material used for roof surface control in underground coal mines. The load-deformation characteristics and the load capacity of welded wire screen were evaluated in the laboratory in a specially built test frame. In the frame, the square screen sections were held in place by bolts and bearing plates at the four corners while a center load was applied to the screen. The parameters evaluated included the wire gauge and configuration, the bearing plate loads and bolt spacing. The wire gauge of the tested screen was 4, 6, 8, 9 and 10. Maximum screen capacities for both load and displacement were developed for each of the wire gauge sizes along with the screen stiffness. This information can be used for screen selection and for the evaluation and determination of screen performance. DISCLAIMER: The findings and conclusions in this report have not been formally disseminated by the National Institute for Occupational Safety and Health and should not be construed to represent any agency determination or policy.

Jan 1, 2009

By R. Fuenzalida

Since 2007, a number of Multivariable Predictive Control (MPC) Applications have been implemented on SAG mills, among others, within the Kairos Mining Concentrator Automation Program using ?Profit Controller?? and other tools comprising the ?Profit Suite??. Along this journey, several interesting and challenging issues related to SAG mill operation and control have been faced, which are relevant to be shared with the Mineral Processing community. These advanced control applications have an operational objective whose goal is to increase marginal profit on the concentrator, together with increasing mill stability. In regard to this objective, the issues to be presented and described are in direct relationship with ?Profit Controller? features and the SAG role; they are also stated and linked to get the most of the mill. Some conclusions and findings are also presented, leading to recommended practices on how to use the controller. These findings have also lead us to decide further actions to be taken on new applications to deploy and also on devising and implementing some complementary components to increase robustness of the overall automation solution, as well as reducing the need for operator intervention.

Jan 1, 2012

By J L. Lett, I Brunton, T Thornhill

Block cave fragmentation has been documented in the literature to have a significant impact on mine design, performance and downstream material handling and comminution processes. Due to this impact, emphasis is placed on the premining prediction and subsequent quantification of primary and secondary fragmentation distribution. This paper discusses the fragmentation prediction and assessment methodology employed at the Ridgeway Deeps (RWD) and Cadia East PC1 (CEPC1) cave operations.Prediction of drawpoint fragmentation was based on an iterative process, which relied on an improved quantitative and qualitative understanding of the rock mass as the mining project developed. In particular, the collection of scanline mapping data provided detailed information in relation to discontinuity trace length, persistence, termination characteristics and large-scale planarity. This allowed an improved estimation of select modelling input parameters, in particular ‘block forming’ discontinuity orientation and strength characteristics.With the start of production, drawpoint fragmentation assessment was undertaken using digital image processing (DIP) techniques for drawpoint extracted tonnes up to 61 000 t. This technique provided a consistent methodology to estimate changes in fragmentation as the block cave matured. It can generally be concluded that the measured mean fragmentation distribution became finer as drawpoint tonnage increased. The incremental change in fragmentation distribution (per 10 000 t) was not uniform, with step changes evident. In addition, for a given geotechnical domain and drawpoint tonnage, the measured fragmentation distribution range was found to vary significantly. A possible explanation for these observations may relate to the disturbed flow behaviour noted from marker experiments at RWD and CEPC1. These experiments indicate that material reporting at the drawpoints (for any given tonnage extracted) may be sourced from highly variable heights within the cave, with finer material preferentially reporting.A comparison between predicted and measured drawpoint fragmentation distribution indicated two general findingsa close match between predicted and measured distributions for material greater than 1.0 m3an under prediction of finer material passing 0.5 m3 relative to measured.The findings would indicate that the fragmentation modelling frameworks utilised at both RWD and CEPC1 were deficient at predicting the percentage of finer material for both primary and secondary fragmentation.The wide range in fragmentation distributions observed in the measured results, and the discrepancy between modelled and measured fines should be considered in the design of mine (material flow, extraction level geometry and draw rate), material handling (crushing and material movement), and downstream milling (comminution and metal recovery) processes for future block cave mines at the Cadia Valley Operations (CVO). With respect to fragmentation distribution range, a sensitivity analysis should be undertaken for these design considerations, with a range in predicted fragmentation distributions investigated (for example, lower quartile, mean and upper quartile). For future mines with similar geotechnical and mining conditions, the calibration of fines should be considered in any fragmentation distribution prediction to match those measured previously.CITATION:Brunton, I, Lett, J L and Thornhill, T, 2016. Fragmentation prediction and assessment at the Ridgeway Deeps and Cadia East cave operations, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 151–160 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

With a price slowly rising above US$35 per ounce gold became a mineral worthy of prospecting and mining endeavour in the early to mid 1970s. Fortune therefore appeared to smile onNew Zealand with its favourable geological environment for gold and past record of major gold production from both hard rock and placer deposits. This was a particularly welcome development as the post war years, including both the base metal exploration boom of 1967/1971 (which produced major nickel, iron and bauxite mines in Australia) and the earlier period of uranium exploration failed to produce any mines in New Zealand with the exception of the small Tui Mine and iron sand mining. Whilst hard rock mining now appears imminent it is 15 years further along the track since the 1967/1971 exploration boom and eight years since the upsurge in prospecting for gold in 1978. New Zealand still has no hard rock base or precious metal mining. This is not for want of proven or potential gold mining situations for these clearly exist at Waihi, Monowai Reef, Golden Cross, MacRaes Flat and elsewhere.

Jan 1, 1986

By R. F. Chaiken

The Bureau of Mines has carried out experimental and theoretical studies with prilled and pulverized ammonium nitrate-fuel oil (AN-FO) mixtures containing varying amounts of fuel oil in an attempt to quantify the effects of stoichiometric composition, nonideal detonation behavior, and expansion volume on the production of CO, NO, and N02 fumes. Experimental fume measurements were obtained in the Bureau's large closed gallery facility (7.2 X 104 liter expansion chamber) and in the standard Crawshaw-Jones apparatus (90--liter expansion shamber) using a prepackaged charge configuration containing about 450 g of explosive.4 The theoretical calculation of toxic fumes was achieved with an equilibrium detonation code called "TIGER,," Contrary to initial expectations, the NOx (= NO + N02) fumes from the large gallery test were found to be in essential agreement with the Crawshaw-Jones results. It was also concluded that (1) "TIGER" calculations offer a good approach to the prediction of toxic fumes; (2) there is a basic problem in extrapolating laboratory measurements of CO fumes to mine conditions--this being due to postdetonation oxidation of CO to CO2; and (3) the detonation velocity decay rate of an explosive is a useful experimental parameter for correlating toxic fumes production with nonideal detonation behavior.

Jan 1, 1974

By Ronald P. Hollenbeck

The value of mineral production in Alabama reached a new high of more than $246 million. 4 percent above the previous record established in 1964. New high values were reported for bentonite, portland cement, fire day, kaolin, miscellaneous clay, lime, crushed limestone, crushed marble, mica. salt, and sand and gravel. Among the States, Alabama ranked second in the production of bauxite and scrap mica and third in the production of native asphalt. The mineral industry of Alabama was dominated by the mining and processing of coal and Slone, the manufacturing of cement, and the production of crude petroleum, which together comprised 85 percent of the total value of mineral output, compared with 84 percent in 1964. The iron ore industry continued to decline. Coal production continued to increase, resulting in the State's coal-mining best year since 1948.

Jan 1, 1967

Microorganisms are finding more use in the mineral industry, with extensive research efforts being reported in 1991. Most of these research efforts were presented in two major meetings, the SME Annual Meeting in Denver (February, 1991) and the Engineering Foundation Conference about Mineral Bioprocessing in Santa Barbara (June 1991). In addition, several articles were published in the IMM Transactions, Minerals and Metallurgical Processing and Water, Air. and Solid Pollution Journal. The literature can be categorized as: • Review articles presenting an overview of the activities in the use of biotechnology in mineral processing. • Research efforts into genetic manipulation of microorganisms to perform a specified job. • Studies in bioleaching of metals from different types of ores. • Biotreatment of wastes from the mineral industry including acidic mine waters, uranium tailings, cyanide destruction, etc. • Investigations into the role of microorganisms in the energy materials, such as oil, coal, tar sands, oil shales, etc. Smith (Mineral Bioprocessing Conference) presented a review of research efforts as well as practical applications of biotechnology in the mineral industry. In another article, Smith et al. (Minerals Engineering) emphasized that extensive fundamentals and applied research work should be pursued to explore the fundamentals, potential and practicality of the various possible uses of microorganisms in mineral engineering.

Jan 1, 1992

By William E. Lardner

Interlocking caisson walls developed from conventional "soldier pile and lagging" shoring. In the latter, the soldier piles receive directly most of the soil load. Natural arches form in the soil behind the shoring; the lagging supports little more than the segment of soil inside the arch. Fig. 1: A typical layout of a lagged wall [ ] Fig. 2: A typical layout of an interlocking caisson wall [ ]

Jan 1, 1987

What is the BC AMTA? ?What is an ASEP? ?Who are the partners? ?Critical Success Factors ?Questions/Answers Aboriginal Skills and Employment Program (ASEP) ?A collaborative partnership of industry, employers, post secondary, First Nations and government ?Working together to plan and implement training and education programs ?Demand-driven: targeted JOBS for participants

May 1, 2010

By P. K. Guerrero, N. Arbiter

The correlation of power consumed by a tumbling mill with the dimensions, speed, and load has been attempted by three principal methods. One of these, the torque formula, has been reviewed critically elsewhere.' This approach, while analytical, disregards the individual motion and speed of the tumbling bodies and assumes that the gross geometry of the entire load is sufficient to establish the power requirement. A more general approach, using dimensional analysis, has been applied in this laboratory by the present authors1'1, and more recently by Rose.3 This disregards the internal conditions within the mill entirely and in effect is an empirical procedure for correlating data. Finally, the complete analysis of tumbling mill dynamics as first made by Davis' attempts to develop the power requirement from individual ball and rod paths and velocities. Although Davis' result is applicable only at a single speed for a given size and load it could be useful, since his optimum speed is at the upper limits of conventional tumbling mill practice. Where power values predicted by the Davis equation were compared with actual mill requirements, they were found too low for small mills and much too high for the largest mills. This suggested that the agreement with actual intermediate range requirements might be fortuitous, and the development of the equation was examined critically. The probable source of error was found to lie in an erroneous assumption made by Davis in converting the energy of ball or rod motion to power. With the same approach, but with different assumptions, a modified equation has been obtained which predicts results that are usually consistently high. This is to be expected, since it is assumed that there is no slip between load and shell and no interference among tumbling bodies. Both these effects should account for the difference. Development of Equation: When a cylindrical shell charged with a substantial weight of rods or balls is slowly rotated about a horizontal axis, the load surface first assumes an inclination that gradually increases to a maximum. Continued rotation results in failure within the load, characterized by a sliding of the top layers down the slope and a reduction in the angle of inclination. Further rotation again increases the angle, and the cycle repeats. If the speed is increased, there is continuous load failure and build-up and a continuous stream of rods or balls descends over the upcoming mass, which moves in circular arcs. At higher speeds the up-

Jan 1, 1961

By Julian Prada

Tunneling requirements are presenting designers with greater challenges. The design and construction of the 2000-ft long unidirectional twin highway tunnels for the approach to one of two bridges of the Louisville-Southern Indiana Ohio River Bridges (LSIORB) Project is no exception. Excavation under low cover, beneath an historic site, with each tunnel of 70-feet wide and 50-feet high dimensions will set precedents for US highway tunnel excavation size. To investigate ground conditions to supplement final design of the highway tunnels, an exploratory tunnel excavated through karstic limestone and shale will be located within the confines of the proposed final alignment. With the LSIORB Project, Jefferson County, Kentucky and Clark County, Indiana will have improved cross-river mobility between them. The Indiana Department of Transportation (INDOT) and the Kentucky Transportation Cabinet (KYTC) are developing the LSIORB Project jointly, in coordination with the Federal Highway Administration (FHWA). Section 4, one of six sections, as shown in Figure 1 is the East End Kentucky Approach and Connections to I-265. Key elements of Section 4 are the twin three-lane highway tunnels under the historic Drumanard Estate. The property is located on the north side of US Highway 42 (US 42) at the intersection with the Gene Snyder Freeway (also KY841) as shown in Figure 2. One aspect of the project consists of the excavation of an Exploratory Tunnel along the southbound alignment tunnel. At the time of preparation of this paper, KYTC has not awarded the Exploratory Tunnel Contract. This paper will focus on the planned geotechnical investigation program that will occur during excavation of the exploratory tunnel and how the design of the twin highway tunnels will incorporate the findings to achieve an innovative and efficient configuration.

Jan 1, 2008

By S. Jayson Ripke, Shane Hoff

Cleveland-Cliffs’ Northshore Mining Company operates a magnetic iron ore (taconite) concentrator and pelletizer in Silver Bay, MN. These are two recent cost reduction projects: 1. Rougher Magnetic Separators were upgraded throughout the concentrator; throughput and recovery were simultaneously improved. 2. Green Ball Roll Screens on one agglomeration circuit were upgraded from 3.5-inch to 2.5-inch rolls. Throughput improved by 24% from 62 to 77 LTPH. Green ball size distribution improved as an added benefit.

Jan 1, 2005

By A. K. Bhattacharya

Cylindrical bridge piers are widely used and equations exist that can predict the maximum depth of local scour around such piers. Scour around piers is an undesirable phenomenon, as it requires the foundation to be placed to a greater depth resulting in increased cost, making it worthwhile to investigate scour-reducing measures. A number of scour-reducing measures have been tried out for cylindrical bridge piers including placing a concrete collar around the pier, having a delta-wing projecting upstream in front of the pier, placing riprap around the pier, using a group of piers instead of a single pier, having a slot in the pier aligned in the longitudinal direction. The objective of this study is to investigate the effect of upstream protective piles on reduction of maximum local scour depth around a cylindrical bridge pier. The upstream piles are placed at different radial distances in front of the pier and the scour depths are observed. The proposed equation of Dey (1997) for determining the maximum depth of scour around a cylindrical bridge pier is used. The reduction of local scour around the pier is compared with local scour around an unprotected pier.

Jan 1, 2009

By Stephen M. Smading

Unique onsite assembly of a 12.43 m Main Beam TBM and back-up system was completed on September 18, 2008 in the remote mountains of the Sichuan province of China. The equipment was assembled onsite, without previously having been assembled and tested in a factory, utilizing a method called Onsite First Time Assembly (OFTA). The Jinping-II hydroelectric project features four parallel headrace tunnels approximately 18 km long, two of which will be excavated by TBMs and two by drill and blast. A nearby fifth tunnel is being excavated by a 7.2 m TBM to draw down ground water in advance of excavating the headrace tunnels. This paper addresses the following topics: ¦Project description including geology and terrain; ¦The decision process leading to onsite first time assembly, the assembly process and logistics, and lessons learned; ¦Design features of the TBM and back-up system; and ¦Operational history from startup to the writing of the paper.

By K. Y. Haramy

Coal mine bumps involve the violent, rapid failure of coal and rock around a mine excavation. Deep coal mines with strong roof and floor rocks and high-stress conditions frequently experience face and rib bumps. The bump problem is becoming more severe as mining depth increases, prompting efforts to control high stress in advance of mining. This Bureau of Mines report presents a review of the most widely used methods to detect and destress high-stress zones along coal faces and an investigation of stress-related bump problems and destressing techniques at a cooperating mine. Geotechnical instrumentation and microseismic methods were used to better understand bump occurrences in underground coal mines. Laboratory tests of the drilling-yield method for high-stress detection were conducted to determine the correlation between the volume of cuttings obtained and the magnitude of the applied stress at various confining pressures. A three-dimensional, multiple-seam computer modeling program, MULSIM, was used to evaluate the effectiveness of stress-relief methods. Modeling results indicate that dangerously high-stress areas can be controlled by either proper planning or destressing. Proper mine planning guidelines and destressing methods such as volley firing, hydraulic fracturing, and auger drilling are discussed.

Jan 1, 1988

By John P. Borovsky

A 3-year study was conducted to evaluate the problems and benefits of using vegetation to stabilize tailing from a potential Minnesota copper-nickel milling operation. The project consisted of three separate investigations: a waste characterization study, a greenhouse study and a field study. With few exceptions, the physical and chemical characteristics of the tai ling were found to lie within the range of properties of Minnesota soils. The tailing lacks organic matter; is deficient in nitrogen, phosphorus and potassium; and may contain elevated levels of soluble salts and heavy metals, particularly copper and nickel. Numerous grasses, forbs and woody plants will tolerate the tailing as a rooting medium. Peat incorporation and topsoil dressing provided few benefits to the revegetation process which were not provided by a fertilizer application. With fertilization, grass/legume production in the tailing was comparable to local agricultural yields. Concentration of heavy metals in grasses grown in the tailing were generally below suggested tolerance limits for plants and animal forage. Legumes tended to accumulate higher concentrations of copper and nickel, and metal uptake of most plants was positively correlated with rate of fertilization. Tailing drainage water contained elevated levels of heavy metals, and establishment of vegetation had little effect on the quantity and quality of tailing drainage water. However, topsoil dressing significantly increased drainage water volume when compared to unvegetated control plots. Copper-nickel tailing revegetation recommendations were developed.

Jan 1, 1983

By Kimberley MacHardy, Ann Maest, Greg Lawson, James Kuipers

Although water quality predictions are often made in Environmental Impact Statements (EIS's) as part of the National Environmental Policy Act (NEPA), comparisons between predicted and actual water quality conditions are rarely reviewed. A comprehensive review of predicted and actual water quality conditions was conducted for a number of large U.S. hardrock mines with EIS’s. For mines with large differences between predicted and actual conditions, factors responsible for the deviations, such as characterization and modeling errors or engineering failures, were identified. Recommendations are made for how the NEPA process could be modified to better predict water quality at hardrock mine sites.

Jan 1, 2005

The Golden Cross mine is a Joint Venture between Coeur Gold New Zealand Limited, as Manager, and Viking Mining Limited. The mine is targeting Zero Lost Time Accidents as a goal.   The Golden Cross operation produces gold and silver from both underground and open pit. The mine is based on an epithermal gold-silver deposit. Treatment of ore is on a campaign basis for each ore type (i.e. underground or open pit). Milling is conventional SAG Mill and Ball Mill grinding circuit followed by carbon in pulp recovery of gold and silver. All tailing materials are treated through the Cyanisorb process to reduce cyanide levels prior to being discharged into the tailings dam.

Jan 1, 1995

By Pierre Lacombe

"The operation of the Louvicourt Mine will have to rely on stringent grade control and on the optimization of the amount of blocked ore made available per given development effort. All of the above being necessary to obtain the highest throughput at the lowest mining cost.To assist in achieving these objectives, the need for production of a competent fill with short curing time was recognized early by the project partners. As well, operating costs associated with the selected method should be as low as possible while meeting the technical criteria.A feasibility study comparing filling methods showed potential benefits in all aspects of the paste fill use, except for its higher capital costs and increased operational complexity. This last consideration was tackled by the conservative design approach adopted in the flowsheet development of the paste fill plant.Since commissioning of the plant has just been completed at this time, the paper will focus on the feasibility study and its background, the design of the plant and testwork results at pilot plant and plant scale.RésuméLe succès de l 'opération de Louvicourt Mine dépendra d' un contrôle serré des teneurs du minerai et de la maximisation de la quantité de minerai développée par effort uni ta ire. Ces critères devant etre respectés afin d'obtenir le taux de production le plus élevé au coût le plus bas.De façon à satisfaire ces contraintes, les partenaires du projet ont reconnu tôt la nécessité de produire un remblai de qualité tout en maintenant un temps de curage court. De plus, les coût d'opération associés a cette opération se devaient d'être des plus avantageux sans sacrifier l'atteinte des objectifs techniques.Une étude de faisabilité comparant différentes méthodes de remblayage a démontré que le remblai en pâte offre des aspects positifs sous taus les angles, si ce n'est de son coût en capital initial élevé et de sa complexité relative d'opération. Ce dernier point fut considéré de près par l'adoption d' une approche conservatrice lors de la conception de l'usine de rernblai.Puisque la mise en service de l'usine n'a été faite que les détails de l 'étude de faisabilité et ses fondements, 1 'usine et des résultats d' essais obtenus a l'échelle de l'usine seront discutés."

Jan 1, 1995

By P. Oyanader

"In 2001, the Catholic University of Chile undertook a maintenance benchmarking study of six open pit copper mines having mill capacities varying between 18,000 t/d and 156,000 t/d, and collectively responsible for 58% of Chilean copper production. This paper describes the methodology used to conduct the study, as well as the overall results. Key performance indices were selected to measure the effectiveness, efficiency, and development of the maintenance process. Using a balanced scorecard philosophy, these indicators were divided into client satisfaction, financial, internal process, and learning and growth indices.Maintenance was found, on average, to be responsible for 44% of mine production costs. Percentage planned maintenance of equipment fleets was found to be low by world standards, averaging 35%, 56%, and 44%, respectively, for blasthole drill, shovel, and haul truck fleets. Fleet availabilities were found to be significantly influenced by the percentage of planned maintenance achieved, while maintenance cost per equipment was found to decrease non-linearly with increases in percentage planned maintenance. Investment in technical training (including planned maintenance practice) was found to be low by global standards. The paper concludes that fleet availability and maintenance costs in Chilean open pit operations could be considerably improved by improving and/or developing maintenance planning standards, and investing in training personnel in planned maintenance techniques"

Jan 1, 2005