Search Documents

By Sandip K. Mukherjee

This report presents the results of the economic analysis of several applicable alternatives to increase airflow in four underground coal mines. Pressure-quantity surveys were conducted underground and measurements were also made at the main mine fan(s). The existing ventilation networks were modeled using the modified Penn State ventilation simulator. The applicable alternatives were simulated. Performance data obtained from these simulation runs were utilized to conduct the cost-effectiveness analysis. The costs for each of the alternatives included capital, operating and operating costs. These costs were expressed as annual ventilation costs per active section in terms of dollars per cfm taking into account the economic life associated with each of the alternatives. The benefits were expressed as increased airflow quantity in the critical sections. A section of this report also deals with comparison of simulator predicted air quantity values against air quantity values measured under-ground. This volume constitutes Volume II of the report and contains the outputs of the computer simulation runs.

Jan 1, 1983

By H. Y. Sohn, Hang Goo Kim

Computer simulations were carried out using calcium ferrite slags containing 25 wt% CaO, and the results compared with those obtained using fayalite slags. There was little difference in overall elimination of Pb and Bi, but elimination of Sb and As was much lower with calcium ferrite slag. When calcium ferrite slag is used only in the converting stage and fayalite slag in the smelting stage, as in the Mitsubishi process, the contents of Sb and As in the blister copper can be kept to reasonable levels. This allows advantage to be taken of the considerably higher iron oxide-holding capacity of calcium ferrite slag than of fayalite slag at the high oxygen potential under converting conditions, thus preventing precipitation of magnetite. Satisfactory agreement was obtained between predicted values and observed data from a Mitsubishi converter

Jun 18, 1905

By F. A. Camisani-Calzolari

The latter half of the 20th century has seen the proliferation of a series of codes to address commodity needs which were brought about by rapidly advancing technologies and the globalization of markets and consumerism. This paper addresses the specific needs and the origin of this surge and presents these codes in the context they were developed. It also compares the main codes or groups of codes and elaborates upon their strengths and weaknesses. Three main categories of codes are identified, namely: codes for reporting to international agencies, codes addressing government needs and, finally, codes for the investors and the stock market. Codes governed by international agencies usually relate to strategic commodities which have highly specialized fields of usage like nuclear power generation where international cooperation is eventually the only viable approach for both the development of technologies and their applications. Codes for reporting to governments address the necessity of each state to exploit their mineral potential profitably and to secure the preservation of wealth for future generations. Reporting to investors is experiencing a considerable popularity as of late because of globalization in mining and the growing need for outside financing of mining projects, whose capital requirements are getting out of reach for the average mid-cap mining company. All these codes have advantages and shortcomings dictated by the specific circumstances under which they were developed, therefore necessitating the definition and implementation of some kind of international standard whereby investments and the spread of information across political boundaries would be facilitated. Though none of these codes might ever become international in the true sense of the word because of significantly different legislations at national level, a step that would greatly contribute to the cross-border disclosure of information would be the reciprocal recognition of competent persons by the major mining countries, including China and Russia. It is also becoming essential that financial institutions and investors be properly advised on mining projects by reporting reserves and resources in a transparent and responsible way with the relevant public disclosures being compiled by professionals who take full responsibility for their submissions. Keywords: reporting codes, mineral resources, mineral reserves, competent person, UN Framework Classification, IAEA classification, JORC Code, SAMREC Code and CRIRSCO.

Jan 1, 2003

By Pravin Kumar

Goldcorp Inc.?s Red Lake Mine (RLM) is situated in the Red Lake Mining District, a history rich North Western Ontario mining community. Red Lake Mine formerly known as the Dickenson Mine has experienced various degree and type of bursting since the 1960?s. During the 1960?s burst were common in shrinkage stope box hole pillars. After discovering the High Grade Zone (HGZ) between its 30th and 39th levels, the mine has changed its mining method to mechanized cut and fill with cemented paste fill. The rock mass at RLM is mainly massive basalt-ultramafic and behaves in a manner consistent with massive brittle rock. This paper presents the use of empirical and numerical design techniques. The use of the Span versus RMR graph to determine critical stope spans at RLM and the use of numerical design techniques to determine the stability of the sills and post pillars. Selecting of a sill pillar dimension is illustrated using four different failure criteria?s. The four failure criteria are m & s failure criteria, the Pillar Stability Graph, deviatoric stress ???-?3), and induced stress level criteria ?1 /UCS, which are calibrated to RLM?s ground conditions. A wide range of case histories has been studied ranging from stable to highly burst prone ground conditions in order to calibrate the failure criteria to observed conditions and quantified to local micro seismic system.

May 1, 2002

By Rajib K. Mohapatra, K. Vizaya Kumar

In any manufacturing organization internal logistics plays a vital role in improving and maintaining the productivity. In Ferro Alloys manufacturing organization where there is huge input of raw material in terms of ore, reductants and variety of fluxes amounting to about four times of the mass of alloy produced need to be handled from yard to furnaces , internal logistics requires utmost attention. Any deviation or mismatch between stock and requirement will affect furnace operation. Though the activities are being outsourced by most of the organization, these require close monitoring. This communication presents an optimization model which can work as a ready reference for the manager to decide upon the material quantity and the furnace to be fed with an objective of minimizing the cost of handling and zero production loss.

Jan 1, 2007

By Luis Maldonado

El presente trabajo señala el desarrollo y aporte de la geotecnia en la minería subterránea, particularmente de la mina Ares, así como define algunos conceptos importantes empleados para determinar los diferentes tipos de refuerzo y/ o sostenimiento utilizados.También evalúa la estabilidad de las labores subterráneas y la elección de un sostenimiento apropiado por zonas delimitadas en los planos geotécnicos. En ese sentido, para la sistematización, cuantificación y calificación de las características geomecánicas de los macizos rocosos, se evalúa las propiedades del macizo como la combinación entre las características de las rocas y sus discontinuidades. De forma que se pueda determinar una cuantificación geomecánica que dilucide el sostenimiento y el método de excavación en base a la más adecuada clasificación requerida.

Sep 13, 2001

By Stephen D. Smith

The following tables summarize data on crude nonfuel mineral production for the United States, its island possessions, and the Commonwealth of Puerto Rico. Although crude mineral production may be measured at any of several stages of extraction and processing, the stage of measurement used in these tables is what is termed "mine output." It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the output from auxiliary processing at or near the mines. Because of inadequacies in the statistics available, some series deviate from the foregoing definition. For copper, gold, lead, silver, tin, and zinc, the quantities are recorded on a mine basis (as the recoverable content of ore sold or treated). However, the values assigned to these quantities are based on the average selling price of refined metal, not the mine value. Mercury is measured as recovered metal and valued at the average New York price for the metal. The values shown are in current dollars, with no adjustments made to compensate for changes in the purchasing power of the dollar.

Jan 1, 1995

By Forrest T. Moyer

To keep the mineral and allied industries informed of trend: in the causes of accidents and to point out the need for corrective measures, the Bureau of Mines collects, analyzes, and publishes, periodically health and safety statistics. This report includes data for 1961 on injury experience, with related employment statistics, at coal mines in the United States. These data are presented in tabular form under the following headings: General Injury Experience Tables 1 to 6: Current data on number of injuries, degree of injury, frequency and severity rates, average severity, and related employment and production data by work location.

Jan 1, 1963

By N. A. Pace

This is one of a series of papers being published by the Federal Bureau of Mines for the dissemination of information on methods and practices used in the mining and preparation of crushed stone for market requirements. Performance in terms of units of work or tons produced per machine and per operator man-hour are given whenever that information is available. Direct operating costs are useful for comparing different methods, and are, therefore, included if possible. In addition to the factual description of equipment and methods used, it is desirable to discuss the engineering reasons for the choices that have been made. This paper is particularly concerned with the opertions at the Columbia plant of Palmetto Quarries Co. of Columbia, S.C. The plant is about one-half mile east of the Congaree River and adjacent to the southwest corner of the city of Columbia. Rail access is by the Atlantic Coast Line Railroad, and by a spur strack of the Seaboard Airline Railroad.

Jan 1, 1962

By Helge Rosenberg

Up to now, Topsøe WSA (Wet gas Sulphuric Acid) plants have been in operation for almost 30 years, and close to 80 plants have been sold. In spite of its unique features and ability to treat gases without any prior drying, the WSA technology has had certain restrictions with regards to SO2 concentration in the feed gas, and the overall conversion of SO2 by catalytic means has been limited to approx. 99.7%. In commercial scale sulphuric acid production on the basis of elemental sulphur and metallurgical off-gases, there is a demand for higher SO2 conversion and treatment of gases with a higher content of SO2. Therefore Topsoe has further developed its WSA technology to cope with these demands. This paper will explain more about the principles of such new development and leave the delegate with a better understanding of the potentials of the new generation of the WSA technology from Topsoe.

Jan 1, 2009

By Norman Disley, David B. Counter, Lionel Hebert

Misfires in underground and surface production blasts can be costly. Costs can arise from loss of resource, production interruptions, having to redrill or otherwise refire the blast (a hazardous process at best), due to added secondary blasting or breakage, and/or from increased LHD maintenance costs attributable to poor fragmentation.

Jan 1, 1996

By E. Niehuis, J. Y. Kim, H. G. Cramer, S. L. Chryssoulis, K. G. Stowe, C. Bendel

TOF-SIMS was used to detect, identify from parent molecular ions and determine the relative concentrations of collectors sorbed on the surface of mineral particles in concentrate and tailings samples from three Canadian concentrators. In the Kidd Creek Zn circuit, sphalerite lost to tailings carried on average a quarter of the amount of isobutyl xanthate present on that recovered to Zn concentrate; amyl xanthate, which is not reported as added to the circuit, was also detected on floated sphalerite and pyrite. At Brunswick, sphalerite particles lost to the scavenger tailings had ten times less amyl xanthate and isobutyl xanthate than those recovered to the Zn final concentrate, while both xanthates were detected on sphalerite floated to the Cu-Pb cleaner circuit. At Matagami, significantly more isopropyl xanthate and isopropyl dithiophosphate were detected on sphalerite recovered to the final Zn concentrate than on that lost to the Zn rougher tailings

Dec 1, 1995

By D. J. Coolidge, H. L. Sheakley

THIS paper does not deal with all sands used in the glass industry in Missouri; it covers only that used in the plate-glass factory at Crystal City. However, it is probably safe to say that other sands, pro- [ ] duced throughout the state for this purpose, are of identical nature. The glass sand used in Missouri is commonly called the St. Peter deposit, which is ascribed to the Ordovician Rock series in the form of sandstone. This St. Peter deposit, aside from a few small outliers, covers a large area of eastern Missouri. It forms, through a broad curve, the northeast margin of the typical Ozark region between Cape Girardeau on the southeast and Mineola, Montgomery County, on the northwest. The belt is extremely irregular, varying from one to ten miles in width; its length is 150 miles in a straight line. [ ] The outcrop near the entrance to the Crystal City mine appears in the form of a sandstone bluff approximately 30 ft. high, running along Plattin Creek (Fig. , I). Above the sand rock an overburden of Joachim limestone appears, which, thickens to nearly 300 ft. and forms the hill commonly called Buck Knob. Test holes, where drilled at various points and the drillers' log indicate that the St. Peter deposit ranges in thickness from 63 to 71 feet. PROPERTIES OT THE ST. PETER SAND From an analysis of the glass sands of the St. Peter formation in Missouri, the follow-

Jan 1, 1942

By Scott A. Stebbins

Cost evaluation models constructed specifically to evaluate the economic potential of an individually motorized railcar system of ore and waste transport demonstrate that the approach may be considerably more cost effective than traditional rubber-tired haulage methods. The system design places a motorized drive unit on each railcar, as opposed to the more common configuration in which a series of un-motorized cars trail behind a single locomotive. These motorized railcars are directed to various load and dump points by a computerized dispatch system, and as such have the advantage of operating unmanned. In addition, the tractive effort of the rail-type drive system is noticeably more efficient than that of the rubber-tired mode of transport. The savings are realized primarily through comparative reductions in the requirements for labor and, to a lesser degree, energy.

Nov 1, 2011

By S. Erçayhan, B. Derin, O. Yücel

In the present study, the production of low carbon ferrochromium (LC-FeCr) from chromite concentrates containing 55.09% Cr2O3 and 13.06% Fe via metallothermic process was investigated. For this aim, in the experiments, the aluminothermic reduction method was applied in an open crucible. 10% CrO3 + 10% NaClO3, 15% CrO3 + 5% NaClO3 and 20% CrO3 by weight of concentrate were added to the charge, respectively and the charge was reduced with aluminium. The experiments were done with the additions of 90, 100, 110, 120 and 130% of stoichiometric requirement of aluminium. The highest Cr content in alloys was found as 71.7% at 120% of stoichiometric Al whereas the highest Cr recovery in alloys was found as 71.8% at 130% of stoichiometric Al when the both charge contained 15% CrO3 + 5% NaClO3 by weight of chromite concentrate.

Jan 1, 2004

Energy Savings and Technology Comparison Using Small Grinding Media Considering the complexity of minerals, the need for finer grinding is increasing along with the energy cost. However, energy is increasing exponentially when grinding finer with conventional grinding balls. The use of small grinding media represents the best potential to improve energy efficiency. Today, it is possible to use grinding media as small as 1 mm. How do they perform in industrial grinding mills? The use of small grinding media (5 - 12 mm), called Millpebs, in regrind mills proved that finer grinding can be achieved at lower energy consumption. In ball mills, energy savings vary from 10 per cent to 40 per cent compared to 25 mm media. A regrind ball mill with a mix of small grinding media can be as energy efficient as an Isa Mill charged with 2.5 and 3.5 mm beads. In vertical stirred mills, energy savings vary from 30 per cent to 60 per cent. To carry out the same final grind, a vertical stirred mill with Millpebs will consume at least 60 per cent less energy than a ball mill using 25 mm grinding media. More potential savings were identified. To achieve those improvements, some operating conditions must be met: 1) feed size should be less than 250 ¦m; 2) the pulp must be fluid enough; 3) finally, the slurry linear velocity should not be excessive. This paper talks about all those industrial results improvement and operating conditions.

Sep 13, 2010

By L. Nahai

THE OUTPUT ff the mineral industry in 1964 in both non-Communist and Communist Europe showed an upward trend for most countries in keeping with the higher index of overall industrial production. Comparable indexes of mineral industry production for non-Communist and Communist Europe (including the U.S.S.R. in Asia) are not available, primarily because the U.S.S.R. does not report details of its industrial production by industrial sectors. However, available data both in the form of index numbers on production published by the United Nations and based on data as reported to the United Nations by the various countries, and actual production data for selected major commodities published by the various European countries reflect generally expanded output by both the extractive sector and the processing sector of the mineral industry in most of the 26 nations of Europe.

Jan 1, 1966

Two concentrates from Palabora, in South Africa, containing 0.056-0.068% undesirable Cu and 0.8 or 2.2% Ti, were chlorinated with air:chlorine ratios of 10:1, 15:1 and 20:1 at temperatures between 1 200 and 1 329 K. The resulting volatile chlorides were condensed and the solutions analysed for Cu, Fe and Ti. Recovery of Cu was less than 25% at low temperatures and short reaction times, but at 1 258 K almost all Cu was removed from the magnetite at all ratios of chlorine to air. At higher temperatures, the increased carrying over of iron as FeCl3 could be minimised by decreasing the partial pressure of chlorine. No titanium was detected in the volatile products and the percentage of Cu recovered was independent of Ti concentration in the concentrates, though as a function of Cl2 vol%, more Cu was recovered at 1 200 K from the low-Ti than from the high-Ti concentrate. In a fluidised-bed reactor, Cu recovery was 58-90% and iron carry-over less than 10 ppm

Jun 21, 1905

The principle activities of the Explosives Research Laboratory from July 1, 1961 to June 30, 1962, are described briefly in part 1. Part 2 gives short abstracts of publications that appeared during fiscal year 1962; in general, the research reported in these publications antedates the report period. Part 3 gives the results of an investigation which, although too limited to warrant separate publication, merits presentation in some detail because of current interest in ammonium nitrate-fuel oil compositions.

Jan 1, 1964

By B. S. Fee, R. R. Klimpel

"Froth flotation is the most widely used and economic means of concentrating metal sulfide ores such as those containing copper, lead, zinc, nickel, molybdenum, and pyrite. Also recoverable are other metal species that are often associated with sulfide ores such as cobalt, platinum, gold, silver, etc. Most of the initial developments made with the process of froth flotation in the early 20th century were based on the processing of metal sulfide ores. It is the relative technical and economic ease of floating metal sulfide minerals with small amounts of appropriate frothers and sulfur containing (thio) collectors that has been a major economic driving force behind the rapid expansion in the supply of metals such as copper, lead, zinc, and nickel that has occurred in the world's economy in the last 50 years. This author estimates that 1.6 billion tons of sulfide ores are processed each year (1980) in the free world based on the froth flotation process.While there has been a tendency for the quality of metal sulfide ores in any one geographic location to deteriorate over time due to mining intensity, the overall global supply of sulfide minerals is still very large. Thus, the physical supply side of sulfide ore concentrates has not been under strong technology improvement pressure with increasing metal demands. Part of this is due to the ability of capital to consistently move to new geographic locations having suitable grade sulfide ores. In these moves, the actual froth flotation technology used (including collector chemicals) has had to change little. As an illustration of this trend, of the approximately 80,000 metric tons of thio collectors used commercially (1980) in the free world, almost 98% were known and manufactured in some form 25 years ago (1). This is clearly not typical of reagent development in other process related industries. In addition, the industrial scale practice of froth flotation applied to sulfide ores has proceeded since the 1920 s with often little direct (predictive) scientific explanation due to the extreme complexity of the flotation process. Empirical testing has been a mainstay of industrial flotation reagent development and use. Even today there is often strong disagreement between researchers as to the mechanisms of chemical flotation practices that have been performed successfully at an industrial scale for many years."

Jan 1, 1987