Search Documents

In September 2003, a test was conducted to see if a115-mm- (4.5-in.-) diam Mocap Vari-Stem blasthole plug could improve the pattern of explosives using different top stemming material. The test took place at the J.S. Faulkroad and Sonsstone quarry in McCalisterville, PA. The test consisted of a production stone blast. Half of the holes were stemmed with standard crushed stone. Two-thirds of the remaining half were stemmed with Vari-Stem plugs and crushed stone. And the remaining one-third of the second 50 percent was stemmed with Vari-Stem plugs and only drill cuttings.

Jan 1, 2004

By Brian Reid

"This paper studies the progress made by hydraulic shovel manufacturers over the last few years, particularly in the areas of productivity increase and operating cost reductions.Five years ago, it was widely considered that the unit production cost for a hydraulic shovel in a mining application was double that of a cable shovel in the same application. The hydraulic machine manufacturers have taken up this challenge, and modern improvements in design, coupled with changes in maintenance techniques, have narrowed the gap to the point where it is valid to ask the question ""will the cable shovel exist in ten years' time?"".Historical BackgroundThe history of the cable shovel goes back to the early 19th century and the industrial revolution. Early machines were steam-powered and ran on rails.The ""power shovel"" and the ""dragline"" were the only mechanical means of mass excavation until the early 1950s. Rail-mounted units gave way to crawlers, which increased flexibility considerably. Some shovels were redesigned as backhoes, and some became extremely large when designed as stripping shovels primarily used in North American coal mines.In the early 1950s growth in hydraulic technology spawned the introduction of the hydraulic excavator, which soon began to replace the smaller cable shovels and backhoes used in the construction industry. They were completely self-contained with either a gasoline or diesel engine and, being much lighter, were more readily transportable.As the excavators grew in size from its early models of 0.5 m3 or less, many of the cable shovel models were discontinued. This was not surprising for several reasons, but the most obvious is that both were often made by the same manufacturer."

Jan 1, 1988

By N F. Fraser

Seafield ResourcesÆ offshore placer gold project covers c.10 000 km2 of the Westland continental shelf between Karamea and Jacksons Head, from the low-water mark out to the 120 m isobath (Figure 1). De Beers Marine (DBM), the marine diamond subsidiary of the De Beers Group, will carry out the project with geological input from Placer Solutions (PSL). DBM bring a wealth of expertise and advanced technology to the project, developed during their 20 years of exploration and mining of diamond placers on the Atlantic shelf of southern Africa, where they have also maintained a strong environmental record.   Glaciers and high-energy rivers emanating from the Southern Alps have transported substantial quantities of gold bearing sediment onto the Westland continental shelf during Pleistocene glacial periods, when fluvial gradients are steeper, sea level is c.120 m lower and most of the shelf is exposed. These deposits have been extensively reworked by the advancing shoreline and marine processes during interglacial marine transgressions, and most are now buried beneath a variable thickness of post-glacial marine sand, silt and mud. DBM will use side-scan sonar, swath bathymetry, Chirp sub-bottom profiling and a magnetometer to map the sea floor and sediments beneath it, guided by PSLÆs predictive geological model for gold distribution on the shelf. Cactus grab and vibro-core samples will be used to ground-truth the geophysics and provide stratigraphic, sedimentological and gold distribution data for incorporation into the geological model. Areas of interest identified by the geophysical and sampling data will be investigated in more detail, with closer-spaced geophysics and Mega-drill sampling to a maximum sediment depth of 20 m beneath the sea floor. These samples will be raised to the ship with air-lift suction technology, processed onboard for mineralogical and grade information, then returned to the sea floor. Environmental baseline data will be gathered from Van Veen grab samples of seabed sediment taken throughout the area during the prospecting programme.

Jan 1, 2005

By H. L. Burmeister

This is one of a series of publications by the Bureau of Mines dealing with mining methods and costs at representative operations in the United States. The report describes all phases of the mining methods for the open-pit operation and milling practices employed at the Vermont Asbestos Mines in Lamoille and Orleans counties, Vermont. A brief history of discovery and development of these asbestos deposits is given, and the ore deposits are described. Methods employed in exploration, sampling, and estimation of tonnage and grade are outlined. A breakdown of available cost figures is summarized in the last section. All asbestos ore produced in this area has been won by the use of surface-mining methods. Two quarries, the Lowell and the "C" Area, are in operation. The quarries combined are producing and the mill is processing approximately 3,500 tons of ore per 3-shift day The average 40,000 tons of crysotile asbestos fiber produced at this plant annually accounted for 96 to 98 percent of the total fiber produced in the United States in 1958. The mine is located (fig. 1) approximately 4 miles north of Eden Mills village on the southeastern flank of Belvidere Mountain (fig. 2).

Jan 1, 1962

By J. J. Sammarco

Illumination is essential for mine safety because miners depend most heavily on visual cues to detect hazards associated with slips/trips/falls and powered haulage. The National Institute for Occupational Safety and Health (NIOSH) is conducting mine illumination research to improve miner safety by enhancing a miner?s ability to see mine hazards. Thus far, 16 papers have been published covering diverse topics such as cap lamps, machine-mounted lighting, glare, lighting maintenance, and light-emitting diode (LED) technology issues. NIOSH has also developed an LED cap lamp, LED area lighting, and a Visual Warning System (VWS). This paper provides an overview of the improvements from NIOSH-developed lighting that include: 94% faster trip hazard detection with the NIOSH LED cap lamp; 79% faster peripheral motion detection to detect pinning/striking hazards; no increase in glare; 71% faster machine movement hazard detection with the VWS. Current research is described concerning an LED cap lamp for metal/nonmetal miners, illumination for refuge alternative deployment and inspection, and whether lighting could be used to improve miner escape and rescue in smoke. Lastly, future possibilities of using lighting to improve miner safety are described.

Feb 27, 2013

By S. Shrivastava, R. G. Reddy

Spent potliner is generated in the electrolytic process of reducing alumina to make aluminum metal using molten fluoride electrolytes. Spent potliner (SPL), obtained at the end of the pots life contains a small amount of cyanide and fluoride which present environmental problems. SPL became a listed hazardous waste under RCRA (KO88) in July, 1990. One of the possible uses of spent potliner is as a substitute for Calcium Fluoride (CaF2) as a fluidizer in iron- and steelmaking and in the glass industry. A low viscosity and a low melting point are prime requirements for accomplishing the above. In the present study, viscosity measurements were performed. Effect of various additives, such as sand, limestone, dicalcium silicate dust, and MgO baghouse dust on the viscosity of SPL was studied. The results showed that with the addition of sand and limestone, very high fluidity of SPL melt can be obtained at significantly low temperatures. The results suggest that spent potliner mixed with additives could potentially be used as a substitute fluidizer.

Jan 1, 1999

By M Fahey

Large volumes of tailings are produced annually by the goldmining industry of Western Australia. This material ishydraulically discharged into large storage facilities usingsub-aerial deposition methods. Much of the gold comes fromhighly weathered rock, resulting in tailings with significant claycontents. Consolidation of these materials can be very slow,particularly if occurring under the effects of self-weight alone.To optimise the consolidation behaviour of the tailings, disposalstrategies can take advantage of the effects of evaporation byallowing each tailings layer to dry before the next layer isdeposited. In the last 20 years, much of the gold processing inWestern Australia has utilised saline groundwater. As the salinetailings dry, the surface will develop a thin salt crust. Laboratorytests have shown that these crusts can drastically reduce thesurface evaporation, adversely affecting the behaviour of thestorage. This problem has been the focus of an extensive researchprogramme, with the objective of obtaining a fullerunderstanding of the mechanisms controlling the coupledconsolidation and evaporation behaviour of saline gold tailings.Part of this study involved site investigations of a wide range ofstorages to ascertain their current states. Methods of gainingaccess to the tailings following deposition were developed.In situ testing and high quality sampling were conducted on each storage and samples returned to the laboratory for analysis. These investigations have enabled full characterisation of the storages to be accomplished. Examples of data are shown herein and the implications of the results are discussed.

Jan 1, 2001

By Carlos Maurício Fontes Vieira

In the present work a ceramic body, fabricated using a mixture of clays and sand, for roofing tiles, produced in Campos dos Goytacazes, north of the State of Rio de Janeiro in Brazil, was characterized. Characterization was performed by X-ray diffraction, thermo analysis, chemical analysis, particle size distribution determination and plasticity. In addition, technological properties related to water absorption, linear shrinkage and flexural rupture strength were determined in samples fired at 700, 900 and 1100oC. The results showed that the investigated ceramic body has satisfactory plasticity and presents a refractory behavior during firing due to the predominantly kaolinitic nature of the clays.

Jan 1, 2006

By V. B. Teffo

The aim of the project was to experimentally determine the coefficient of restitution, and static and rolling friction of Eskom-grade coal for discrete element modelling (DEM). These parameters will be used in further DEM studies to simulate the flow and behaviour of coal during conveyance. For the simulation to yield realistic results, the parameters for the different coal shapes identified in the samples were determined. DEM uses spherical particles, and it was found that the difference between the DEM default parameters and those measured is significantly different, by as much as 97%, which illustrates the importance of experimentally determining these parameters. The spherical particles in DEM can be used to construct the various coal shapes identified, and the parameters measured can be used to simulate realistic results. The conveyance system can then be optimized accordingly.

Jan 1, 2013

Core samples, which were collected by the author from the Busang prospect, East Kalimantan, reflect a progressive evolution of a large magmatic-related hydrothermal system that is comparable to that encountered in many similar systems elsewhere in the Pacific region. The initial, localized deposition of sheeted porphyry quartz-molybdenite veins took place at high temperatures and fluid salinities, and at relatively deep levels. This was followed by an extensive phase of phyllic (sericite-quartz-pyrite ¦ tourmaline-apatite) wallrock replacement and vein formation. Propylitic (epidote-chlorite-carbonate-quartz) alteration was formed marginal to the phyllic assemblages. These porphyry-related events were centred in the Southeast Zone, and are probably associated with the emplacement of a felsic intrusion at depth. This event contributed only trace gold to the system. The early stages of hydrothermal activity were followed by an episode of quartz (¦ adularia) û carbonate û base metal sulfide veining, which was accompanied by argillic (illitic-kaolin clay) wallrock alteration. This event was sulfide-rich in the Central Zone and carbonate-dominated in the Southeast Zone. Gold mineralisation was observed in Central Zone drillcore to be associated with both sulfide, as well as carbonate, deposition. A final stage of epithermal-style quartz ¦ stibnite û realgar veins are, in the Central Zone, locally gold-bearing. The latter two events are interpreted to be associated with the late-stage exsolution of metal-bearing brines from the felsic intrusion that formed the earlier porphyry quartz-molybdenite veins and widespread phyllic-propylitic alteration.

Jan 1, 2002

By R. Stefanko

This Final Report covers the work performed for Contract No. H0377043, "Cables for Face Equipment" from August 1, 1977 to April 1, 1981. It reports the findings in three areas of research: cable protection, circuit-breakers, and high-voltage cable couplers. Laboratory and analytical studies have been conducted in the three areas to determine proper circuit-breaker settings, cable sizes, and coupler performance. Also, an extensive field-monitoring program was established to relate in-mine epxerience to laboratory findings. Further, various pieces of equipment was designed for laboratory testing, particularly in the area of cable reeling and unreeling.

Jan 1, 1981

The stability of surfactant-free foam films was studied using the thin film pressure balance (TFPB) technique. In pure water, it was not possible to produce foam films due to weak film elasticity and strong hydrophobic force. In the presence of NaCl, however, the hydrophobic force was sufficiently dampened to allow metastable films to form. At 10-5 M NaCl, the equilibrium film thickness reached a maximum of approximately 130 nm at pH 6.0-7.3. The thinner films obtained on either side of this pH range was due to the increased ionic strengths associated with the HCl and NaOH additions for pH control.

Jan 1, 2009

To provide cooler air to miners working in hot areas of mines, particularly new deep hardrock mines. Approach Air supplied to hot working areas of mines is cooled by passing it through a series of water sprays. How It Works Water nozzles mounted inside a section of ventilation tubing release cooling sprays of water into the air being blown through the tube. The prototype of the water spray cooler consists of six evenly spaced water sprays located inside a 10-ft. long section of 16-inch-diameter fiberglass ventilation tubing. See diagram. This section of rigid tubing is installed into one of the positive pressure ventilation tubing lines that conduct fresh air into working stopes. The intake manifold to the six water sprays is connected to the mine?s cool water line, and the water valve on the manifold is opened. Warm ventilation air being supplied to the stope passes through the water sprays, and is cooled by the lower temperature water.

Jan 1, 1979

By V Barrera, A Brzovic, M Gaete, L Burgos, E Arancibia

Fragmentation is one of the most relevant parameters in the design and operation of a mine using the caving mining method. Fragmentation affects all subsequent operations, including extraction, comminution processes, secondary blasting and transportation.There are a number of different models in the literature to estimate the size of the ore fragments that report to the drawpoints; however, there is still no industry consensus about which one to use. This paper proposes a new model for predicting the fragmentation reporting to the drawpoints that is based on the geotechnical unit characteristics, extraction height and column of primary ore. The model is developed from observations of fragmentation measurements in different mine sectors of Codelco’s El Teniente mine in Chile.This work focuses on the following three steps:collecting fragmentation and hang-up data from several mine sectorsdeveloping a geotechnical block model using oriented core placed within the main geotechnical unitsanalysing the data and modelling the fragmentation process.The proposed model is used to discuss the mechanisms and the influence of preconditioning on the size of the ore fragments that report to the drawpoints.CITATION:Brzovic, A, Vallejos, J, Arancibia, E, Burgos, L, Delonca, A, Gaete, M and Barrera, V, 2016. Analysis and modelling of the fragmentation process – case studies at El Teniente Mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 305–310 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By A. M. Krzanowski, T. S. Golosinski

"This paper presents results of a study undertaken to determinethe feasibility of mining plains overburdens with bucket wheel excavators. Based on extensive geotechnical testing of overburdens under study, the relations between material geotechnical properties and its cuttability were defined. The properties with the highest correlations to the cuttability werethen used to develop the material diggability classification. This classification may be used for identification of overburdens and coals mineable by bucket wheel excavators.IntroductionLow cost of mining and high productivity can be achieved when mining unconsolidated soils and soft rocks with bucket wheel excavators. As a result this mining equipment will likely be introduced into plains coal mines. At present there are plans to use a bucketwheel excavator (BWE) in at least one mine by the end of this decade. Unfortunately, the performance of a BWE deteriorates rapidly with the increasing strength of mined material. To avoid costly misapplication, material diggability must be defined in advance of an application (i.e. the force required at the cutting edges of BWE buckets must be quantified). Correct definition of material diggability permits reliable selection of a BWE, or may indicate unsuitability of this equipment for a particular application.The reported studyu i was undertaken to investigate the diggability of typical prairie overburdens and thus provide a guidance for likely future applications of bucketwheel equipment. Investigations concentrated on the parts of overburden most likely to create problems for a BWE mining. These are defined in Table 1. At present, thin layers of the two investigated materials (samples K and L) are mined by a BWE in an oil sand mine, after being loosened by blasting."

Jan 1, 1987

By Willem Le Roux

Occupational health and safety is regulated by statute and common law. South Africa has, like many other countries, legislated extensively on occupational health and safety. Despite the body of legislation, the common law continues to play an important role as far as it concerns contractual, delictual and criminal liability. Two major Acts regulate occupational health and safety viz. the Occupational Health and Safety Act, No. 85 of 1993 (?OHASA?) and the Mine Health and Safety Act, No. 29 of 1996 (?MHSA?). The MHSA applies to mines and works as defined and related aspects. OHASA applies to other industries but does not apply to employers and workplaces to which the MHSA and certain matters covered by the Merchant Shipping Act, No. 57 of 1951 apply. See section 1(3) of OHASA. 2 The employer?s health and safety obligations in terms of the MHSA 2.1 Section 2(1) of the MHSA provides amongst others, as follows: ?The employer of every mine that is being worked must: (a) ensure, as far as reasonably practicable, that the mine is designed, constructed and equipped: (i) to provide conditions for safe operation and a healthy working environment (ii) ... (b) ensure, as far as reasonably practicable, that the mine is commissioned, operated, maintained and decommissioned in such away that employees can perform their work without endangering the health and safety of themselves or of any other person?.

Jan 1, 2011

By J. C. Edwards

The National Institute for Occupational Safety and Health (NIOSH) implemented a real-time neural network system which can discriminate mine fires from nuisance diesel emissions as part of an atmospheric mine monitoring system in NIOSH?s Safety Research Coal Mine. The real-time response of a neural network to fire sensor outputs was demonstrated for coal and belt combustion in the presence of diesel emissions. The fire sensors consisted of an optical path smoke sensor, a carbon monoxide (CO) sensor, and two types of metal oxide semiconductor (MOS) sensors. The real time neural network was trained with coal, wood, and belt fire experiments with and without diesel emissions background. The trained neural network successfully predicted mine fires with these combustibles in the smoldering stage prior to the onset of flames.

Jan 1, 2005

By H. Rossmanith

This contribution introduces the fundamental concepts of wave propagation and fracture mechanics which form the basis of electronic blasting, i.e. precise initiation timing using electronic detonators. The concept of Lagrange diagrams will be frequently used for the calculation of the delay time between blast-holes in a row and rows of blast-holes. The effect of burden and structural geology will be briefly touched. It is found that the advanced blasting technology based on the use of electronic detonators introduces a change of paradigm. It will be shown that knowledge in wave propagation and fracture mechanics is essential for the successful application of the new blasting technique in industry. In particular, the delay time, the wave speeds in the rock mass, the shape of the wave pulse and the acoustic impedance mismatch have become decisive parameters in advanced blasting. Utilizing the wave speed and wave shapes of detonations, large scale tests Utilizing the wave speed and wave shapes of detonations, large scale tests in various countries (Australia, Chile, etc.) have shown that optimal delay timing requires shorter delay times in conjunction with allowing for a wider drilling pattern and the use of a reduced amount of explosives, i.e. a lower powder factor. This seemingly contradictory arrangement is fully justified by using scientific principles in blasting, and converting blasting from an art to a scientific discipline.

Jan 1, 2003

By B. Gigas, M. Preston, M. Giralico

Optimized mixer settler designs will now handle total flows of over 6,000 m3/hr.Computational Fluid Dynamics (CFD) is a timely and predictable tool for design development. Lightnin has the capability of using numerical analysis methodology to evaluate flow patterns and phase separation. CFD can show performance differences between changes, in mix tanks, in settler geometry, and in liquid depth, against variable flow rates. Understanding the differences allows the development of optimized designs. This paper focuses on the major design components of the mixer settler and how technological advances will lead to further improvements, when designing for today’s largest flow plants.

Jan 1, 2004

By Richard Gertsch, Jack Eloranta, Leslie Gertsch

An ongoing research program is characterizing the ore qualities that most affect mine and mill processing of iron. Current practice uses assays of magnetic iron and silica, but additional qualities are needed for advanced process control. If additional qualities can be measured from core, blastholes, or process samples, they can be modeled and controlled similarly. What qualities, other than assays, hinder or facilitate beneficiation at each processing step, and how can they be measured in the mine/mill ore stream? This paper describes preliminary determinations of the effects of ore chemistry, hardness, blasthole drill performance, fragmentation control, and grindability on mill performance.

Jan 1, 2005